Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹42.8 LAccepted-AOC 18TH FLOOR FL NO 1801 PANCHASHEEL HEIGHT MAHAVEER NAGAR KANDIVALI WEST MUMBAI 400067 | MUMBAI | MUMBAI SUBURBAN | MAHARASHTRA | 400067 | ₹42.8 L | L1 | Accepted-AOC Admitted Found Reasonable for acceptance |
| 2 | L2₹44.0 LAccepted-AOC 301 CHAMUNDA ENCLAVE PLOT NO 89 AIROLI SECTOR 8A NAVI MUMBAI 400 708 | THANE | MAHARASHTRA | 400708 | ₹44.0 L | L2 | Accepted-AOC Rejected
L1 being accepted |
| Sl No | Description | Qty | Unit | KAJAL CONSTRUCTION L1 | S K ENTERPRISES L2 |
|---|---|---|---|---|---|
| 1.00 | Taking down cement plaster of any description on stone /PCC block /brick wall / top of chajja etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris to outside of INS Mandovi Area including filling of open joints in cement mortar 1:6 complete all as specified and directed. | 400 | Sqm | 45 ₹18,000 | 33 ₹13,200 |
| 2.00 | M & L for rendering 15 mm (10+5) thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 in two layers i.e first layer 10 mm thick and 5 mm thick outer layer mixed with WPC as per manufacturer's instruction and surfaces finished even and smooth without using extra cement complete all as specified and directed.
Note : Quoted rate shall be deemed to be inclusive of cost of WPC. | 150 | Sqm | 400 ₹60,000 | 350 ₹52,500 |
| 3.00 | M & L for preparation of newly plastered wall surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. | 150 | Sqm | 250 ₹37,500 | 200 ₹30,000 |
| 4.00 | M & L for dubbing out average 15 mm thick on irregular face of external and internal wall surfaces (when specifically ordered in writing) in CM 1:6 complete all as specified and as directed. | 30 | Sqm | 300 ₹9,000 | 210 ₹6,300 |
| 5.00 | M & L for rendering 10 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces and surface finished even and smooth without using extra cement complete all as specified and directed.. | 150 | Sqm | 350 ₹52,500 | 250 ₹37,500 |
| 6.00 | M & L for preparation of newly plastered wall surfaces, providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth, priming with alkali resistant priming paint and distempering with two coats of distemper oil emulsion, white or tinted, complete all as specified and directed. | 150 | Sqm | 300 ₹45,000 | 150 ₹22,500 |
| 7.00 | M & L for rendering 5 mm thick in cement mortar 1:3 on fair faces of brick work or concrete soffit of chajja and roof projection or other similar works and surface finished even and smooth without using extra cement complete all as specified and directed. | 100 | Sqm | 300 ₹30,000 | 300 ₹30,000 |
| 8.00 | M & L for preparation of newly plastered ceiling surfaces, providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth, priming with alkali resistant priming paint and distempering with two coats of distemper oil emulsion, white or tinted, complete all as specified and directed. | 100 | Sqm | 250 ₹25,000 | 200 ₹20,000 |
| 9.00 | M & L for preparation of old plastered wall surface including washing down, rubbing down and stopping of distempered wall surfaces, making surface smooth by applying ready mix putty where ever required and distempering with two coats of distemper oil emulsion, any tint, complete all as specified and directed. | 500 | Sqm | 250 ₹1.3 L | 200 ₹1 L |
| 10.00 | M & L for preparation of old plastered wall surface including washing down, rubbing down and stopping of distempered wall surfaces, making surface smooth by applying ready mix putty where ever required and distempering with one coat of distemper oil emulsion, any tint, complete all as specified and directed. | 500 | Sqm | 250 ₹1.3 L | 200 ₹1 L |
Updated dates
Tender Value
₹44.9 L
EMD Value
₹89,800
Closing Date
15 Dec 2025, 6:00 pmClosed
GE (P) Navy Mandovi
GE (P) Navy Mandovi Military Engineer Services INS Mandovi
As per tender documents
2025_MES_739642_1
8661/E8 GE (P) NAVY MANDOVI
Open Tender
Civil Works
180 days
INS Mandovi
Please refer Tender documents.
8 documents required · 8 mandatory
₹500
GE (P) Navy Mandovi
₹89,800
Yes
20 Jan 2026
13 Nov 2025
17 Dec 2025
13 Nov 2025
15 Dec 2025
27 Nov 2025
13 Nov 2025 - 26 Nov 2025
Amount
Taking down cement plaster of any description on stone /PCC block /brick wall / top of chajja etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris to outside of INS Mandovi Area including filling of open joints in cement mortar 1:6 complete all as specified and directed.
M & L for preparation of newly plastered wall surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.
M & L for dubbing out average 15 mm thick on irregular face of external and internal wall surfaces (when specifically ordered in writing) in CM 1:6 complete all as specified and as directed.
M & L for rendering 10 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces and surface finished even and smooth without using extra cement complete all as specified and directed..
M & L for preparation of newly plastered wall surfaces, providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth, priming with alkali resistant priming paint and distempering with two coats of distemper oil emulsion, white or tinted, complete all as specified and directed.
M & L for rendering 5 mm thick in cement mortar 1:3 on fair faces of brick work or concrete soffit of chajja and roof projection or other similar works and surface finished even and smooth without using extra cement complete all as specified and directed.
M & L for preparation of newly plastered ceiling surfaces, providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth, priming with alkali resistant priming paint and distempering with two coats of distemper oil emulsion, white or tinted, complete all as specified and directed.
M & L for preparation of old plastered wall surface including washing down, rubbing down and stopping of distempered wall surfaces, making surface smooth by applying ready mix putty where ever required and distempering with two coats of distemper oil emulsion, any tint, complete all as specified and directed.
M & L for preparation of old plastered wall surface including washing down, rubbing down and stopping of distempered wall surfaces, making surface smooth by applying ready mix putty where ever required and distempering with one coat of distemper oil emulsion, any tint, complete all as specified and directed.
M & L for washing down, rubbing down and stopping of old plastered wall surface and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces complete all as specified and directed.
M & L for washing down, rubbing down and stopping of old plastered wall surface and applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces complete all as specified and directed.
M & L for complete removal of existing treatment and preparation of old ceiling surfaces and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.
M & L for preparation of old plastered wall surfaces and applying two coats of white wash complete all as specified and directed.
M & L for preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.
M & L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.
M & L for chipping, removing carefully concrete work using low impact hammer, breaking without damaging the structure, cleaning and disposing debris outside the premises complete all as specified and directed. Note: Hard concrete shall not be removed by force.
M & L for chipping off existing loose, damaged concrete from all affected RCC structural elements (columns, beams, slabs chajjas etc), on external and internal facades etc beyond main reinforcement (as per recommendation in Structural Audit Report), carefully with chisel and hammer, applying rust remover (“Rusticide SS” or equivalent) and cleaning washing etc of existing reinforcement bars using wire brush, applying two coats of rust preventor slurry made out of rust passivator (“Polyalk Fixoprime” or equivalent) and cement in proportion 1:1.5 to reinforcement bars; applying a bonding coat of slurry made out of acrylic polymer (“Polyalk EP” or equivalent) and cement in proportion 1:1 to concrete and reinforcement substrate; and providing Ready mix Polymer modified cement mortar of minimum M40 grade to RCC members including hand packing, curing and making the surface rough for plastering complete all as manufacturer's instructions and as specified and directed.
S & F wire netting of stainless steel wire 1.4 mm dia (size of mesh 25 mm) fixed with tinned tacks of stainless steel wire staples, including necessary frame of steel complete all as specified and directed.
M & L for injecting low viscosity MONOPOL (3-5cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories, till nozzles refuse to accept the grout, including mixing of material components (Part a & b) in quantities as per manufacturer's instruction by weigh batching, grouting by maintaining the pressure at exit (0.5 to 1.0 kg/cm2) by monitoring pressure guage at exit, grouting the material through prefixed nozzles in the structural elements @ 100ml per nozzle and repeating the process for all the nozzles (beam and columns) complete all as specified and directed.
Removing plant growth including its roots and upto 1.00m of plant height at any location/at any storey and of any description and treating the surfaces with hydrocholic acid (HCl) and making good surfaces with cement mortar 1:4, complete all as specified and directed.
M & L for opening the separation cracks and providing “V’’ grooves, 2’’ to 3’’ from the either side of the cracks by carefully marking the areas to be opened, at junctions of RCC and masonry wherever directed and instructed, using cutting machine and by skillful and /careful chiseling with a well sharpened chisel and hammer as directed, including wire brushing and washing of concrete substrata and masonry walls with water jet to the surfaces thus prepared to the entire satisfaction of the Engineer-in-charge, complete all as specified and directed.
M & L for moistening cracks/ grooves provided here-in-before under Item No. 23 applying to the prepared surfaces priming/ bonding coat of slurry made out of acrylic polymer (“Polyalk EP” or equivalent) and cement in proportion 1:1, filling the cracks/ grooves by Providing and applying ready mix Polymer modified cement mortar in 1:5:15 ratio of acrylic polymer (“Polyalk EP” or equivalent), cement and graded sand/ quartz sand, respectively, on the prepared surfaces and finishing it in level with the existing plaster, including handpacking, curing and making the surface similar to the external plastering using wooden floats/ punch etc. complete all as specified and directed.
M & L for providing TMT bars mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.
Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.
M & L for providing 75mm thick PCC 1:3:6 type C2, using 40mm graded stone aggregate as in plinth protection, finished even and smooth without using extra cement including joint filling by mastic asphalt complete all as specified and directed.
Demolition of precast concrete articles and precast concrete block walling built in cement mortar or cement lime mortar complete all as specified and directed.
M & L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type C1 using 20 mm graded trap aggregate, exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.
M & L for preparation of new plastered wall surfaces and applying two coats of white wash complete all as specified and directed.
Disconnecting existing tanks of capacity exc. 250 ltr and n.exc. 500 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required, reconnecting and re-fixing in position complete all as specified and directed.
Disconnecting existing tanks of capacity exc. 500 ltr and n.exc. 1000 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required, reconnecting and re-fixing in position complete all as specified and directed.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.
M & L for 15mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed.
M & L for rendering 10 mm thick on fair faces of brick work or concrete vertical surfaces in cement mortar 1:4 complete all as specified and directed.
M & L for granite tile flooring using granite (of any type) tiles, 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.
Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and directed.
M & L for glazed ceramic coloured tiles in vertical surface, 350 x 250 x 7 mm/ 450 x 350 x 7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.
M & L for non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.
M & L for non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.
M & L for non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.
M & L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments complete all as specified and directed.
Taking down steel tubing and connections of 15 mm dia bore complete all as specified and directed.
Taking down steel tubing and connections of 20 mm dia bore complete all as specified and directed.
Dismantling water tanks of capacity exc 250 ltr & n exc 500 ltr and removing to store complete all as specified and directed.
Dismantling water tanks of capacity exc 500 ltr & n exc 1000 ltr and removing to store complete all as specified and directed.
Supplying and laying of CPVC pipes of 20 mm outer dia, SDR 11 & plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and directed.
Supplying and laying of CPVC pipes of 25 mm outer dia, SDR 11 & plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and directed.
S & F in repairs bib taps (long body), cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15mm dia bore complete all as specified and directed.
S & F in repairs stop valves, copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends, for iron pipes or for unions of 15 mm dia bore complete all as specified and directed.
S & F in repairs pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with fly nuts screwed for iron pipes of 15 mm dia bore complete all as specified and directed.
S & F in repairs brass chromium plated shower rose, 125 mm size with shower arm of 15 mm size, 195mm long with 45 degree bend and flange complete all as specified and directed.
S & F PTMT bathroom mirror cabinet of size 600mm x 450mm x 200mm with all necessary arrangements for fixing to wall complete all as specified and directed. Make: Shakthi Cat Pt No SB-155 or Water Tec or equivalent
S & F in repairs plastic water closet seat, white, closed pattern with flat bottom, cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.
S & F stainless steel toilet paper holder, flat recessed type complete all as specified and directed.
S & F in repairs brass, tubular towel rail, chromium plated, 20mm dia, including all fittings complete all as specified and directed.
S & F in repairs grating doom 100mm dia of PTMT (Minimum weight 40 gms) including jointing with solvent cement complete all as specified and directed.
S & F in repairs 32 mm dia waste pipe, 800 mm long complete all as specified and directed.
S & F in repairs 2 in 1 health faucet with hook, chromium plated, with 1.5 m tube complete all as specified and directed.
S & F in repairs vitreous China wash down water closet pan (pedestal pattern), white, excluding flushing cistern, but including plastic water closet seat, black/ white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.
S & F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm, white, with integral foot rests complete all as specified and directed.
S & F Vitreous China Urinal, full stall wall hung type, white (excluding flushing cistern, flush pipe and waste pipe) white, including securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing union for discharge pipe and bedding urinal against wall in CM 1:2 complete all as specified and directed.
S & F PVC valveless, syphonic action type, flushing cistern of 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets and 32 mm dia flush pipe of polyethylene of low or high density or PVC, and making connections to pipes and fixing of chain and pull, or lever, if any complete all as specified and directed.
S & F PVC connections of 15 mm size and 450 mm long with PTMT nuts complete all as specified and directed.
S & F PVC connections of 15 mm size and 600 mm long with PTMT nuts complete all as specified and directed.
S & F in repairs wash basins, Vitreous China, flat back or angle back type, 550mm x 400mm size, including brackets and cutting for and pinning in ends of brackets or erecting stand including supply and fixing of 32 mm dia polyethylene of low or high density or PVC waste pipe complete all as specified and directed.
S & F in repairs sinks with drainage board made of stainless steel 1 mm thick, kitchen with plugs, washers and wastes; includding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, of overall size 915mm x 460 mm and of bowl size 410mm x 330mm x160mm complete all as specified and directed.
S & F 500 litre capacity rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and directed.
S & F 1000 litre capacity rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and directed.
S & F in repairs ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 25 mm dia bore complete all as specified and directed. (minimum weight 25 mm - 455 gm)
S & F in repairs CPVC ball valves of 25 mm dia bore complete all as specified and directed.
S & F in repairs CPVC tank adaptor 25 mm dia bore complete all as specified and directed.
M & L for providing PVC (SWR) floor trap of 75 mm dia outlet, plain with grating including jointing with solvent cement, fixed in repairs, complete all as specified and directed.
Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.
S & F PVC (SWR) pipes of 160 mm dia bore, single socketed in any length with rubber ring joints, fixed to walls/ columns complete all as specified and directed.
S & F PVC (SWR) bends, any radius, 160 mm bore with access door complete all as specified and directed.
S & F PVC (SWR) pipes of 110 mm dia bore, single socketed in any length with rubber ring joints, fixed to walls/ columns complete all as specified and directed.
S & F PVC (SWR) bends, any radius, 110 mm bore with access door complete all as specified and directed.
Taking down shutters of any descrption not exceeding 1.0 sqm each from chowkhats, complete all as specified and directed.
Taking down shutters of any description, exceeding 1.0 sqm but not exceeding 2 sqm each, from chowkhats, complete all as specified and directed.
Taking down chowkats or frames not exceeding 1.5 sqm each, with shutters (without taking off shutters from the frames) complete all as specified and directed.
Taking down chowkats or frames exceeding 1.5 sqm but not exceeding 4.0 sqm each, with shutters (without taking off shutters from the frames) complete all as specified and directed.
Taking down shutters of any description n exc 1 sqm each and refixing in same opening complete all as specified and directed.
Taking down chowkats or frames exceeding 1.5 sqm but not exceeding 4.0 sqm each complete all as specified and directed.
Taking down shutters of any description exc 1 sqm and n exc 2 sqm each and refixing in same opening complete all as specified and directed.
S & F 2nd class hard wood, 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); and fitted to chowkats complete all as specified and directed.
M & L for forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, in CM 1:6 complete all as specified and directed.
S & F mild steel ordinary rat tail door springs (capsule type), 300 mm long, including roller and roller plate complete all as specified and directed.
S & F in repairs mild steel ordinary rat tail door springs (capsule type), 300 mm long, including roller and roller plate complete all as specified and directed.
S & F extruded aluminium alloy handles, 150 mm long, fabricated type, anodised complete all as specified and directed.
S & F in repairs extruded aluminium alloy handles, 150 mm long, fabricated type, anodised complete all as specified and directed.
S & F extruded aluminium alloy handles, 100 mm long, fabricated type, anodised complete all as specified and directed.
S & F in repairs extruded aluminium alloy handles, 100 mm long, fabricated type, anodised complete all as specified and directed.
S & F aluminium anodised, barrel tower bolts of extruded section and 150 mm length complete all as specified and directed.
S & F in repairs aluminium anodised, barrel tower bolts of extruded section and 150 mm length complete all as specified and directed.
S & F aluminium anodised, barrel tower bolts of extruded section and 100 mm length complete all as specified and directed.
S & F in repairs aluminium anodised, barrel tower bolts of extruded section and 100 mm length complete all as specified and directed.
S & F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.
S & F in repairs 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.
S & F in repairs aluminium plate type II, gate and shutter, hooks and eyes of size 150 mm complete all as specified and directed.
S & F in repairs 125 mm long hasp and staple, safety type, aluminium anodised hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.
S & F 100 mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.
S & F 75 mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.
S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty / beeding in squares not exceeding 0.5 sqm in each pane complete all as specified and directed.
Hacking out old broken glass (any thickness, size, quality or description) from wooden/ steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.
S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty / beeding in squares exceeding 0.5 sqm in each pane complete all as specified and directed.
S & F 4 mm thick figured glass, pin head type and glazing with oil putty/ beeding in squares exc 0.5 sqm in each pane complete all as specified and directed.
S & F aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with aluminium wire staples complete all as specified and directed.
S & F in repairs aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with aluminium wire staples complete all as specified and directed.
S & F mild steel clamps; hold fasts; wall ties and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.
M & L for providing PCC 1:3:6 type C1 using 20mm garded stone aggregate, for fixing hold fast complete all as specified and directed.
S & F in repairs door closer, hydraulically regulated, designation No. 3, universal type, aluminium (die cast) body, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.
S & F in repairs 40 mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed.
S & F in repairs snake guards on bottom sides of doors (door sealing strip) of aluminium plate and nylon bristles for weather stripping, air and sound blocking complete all as specified and directed.
S& F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of Frame size 65x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with and including MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge, as per specification & drawing Note: 1. For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. 2. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.
S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: Stainless steel butt hinges and necessary S S screws shall be paid separately under relevant item of this schedule.
S & F in repairs floor door stopper of aluminium alloy body and tongue, anodised with hard draw steel spring, 140mm overall length of cover plate complete all as specified and directed.
M & L for providing 18/19 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed in repiars with screws to timber frame work in cup board shelves complete all as specified and directed.
S & F continuous (piano) hinges, mild steel, bright finish or electrogalvanised, of 30mm wide flaps (when open) complete all as specified and directed.
S & F in repairs continuous (piano) hinges, mild steel, bright finish or electrogalvanised, of 30mm wide flaps (when open) complete all as specified and directed.
S & F hasp and staple, 100mm long, safety type, aluminium anodised including bolt to hinge plate and fixed with screws complete all as specified and directed.
Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required, depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall exc. half brick but not exc.one brick complete all as specified and directed.
S & F in repairs mild steel mortice lock, 4 lever, vertical type, size 65 mm complete all as specified and directed.
S & F in repairs 100 mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.
S & F in repairs 75 mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.
M & L for greasing and easing only to existing rolling shutters, area of shutter exc 5.0 Sqm and not n exc 10 Sqm each complete all as specified and directed.
S & F in repairs curtain rails of anodised aluminium alloy with fixing brackets, stops, rollers etc complete all as specified and directed.
S & F aluminum powder coated window/ ventilator shutter including frame, any type (sliding or open-able) and other similar work etc, fabricated, with approved standard sections, including necessary arrangement to receive 4mm thick sheet glass or wire mesh with aluminium channel beading, stainless steel screws, rollers, maruti lock including the cost of rubber gasket / rubber beading, rollers, maruti lock etc, fixing frames complete all as specified and directed. Note: Weight of rubber gasket / beading rollers, maruti lock will not be measured with weight of aluminium shutter. Note: Sheet glass & wire mesh shall be measured and paid separately.
S & F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement complete all as specified and directed.
Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.
S & F structural steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; confirming to Fe 290 (Gde E-165), also fastening and fixing complete all as specified and directed.
M & L for providing cement concrete 1:2:4 type B2 using 40 mm graded stone aggregate as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) including necessary formwork complete all as specified and directed.
M & L for providing cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in lintels upto 1.5m clear span, cills, steps; copings, kneelers, apex stones, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary formwork complete all as specified and directed.
M & L for providing 100 mm thick cement concrete 1:3:6, type C-2, using 40mm graded aggregate, finished even and smooth without using extra cement as in sub-floors, sub-bases, floors and pavings complete all as specified and directed.
M & L for sand filling under floors or in foundations including watering and consoildation complete all as specified and directed.
M & L for machine pressed precast conctete interlocking paver block, any shape and size, of 60 mm thickness, M-35 grade, confirming to IS 15658-2006, fixed with grey cement & pigments complete all as specified and directed.
Dismantling fencing wire mesh, any type complete all as specified and directed.
Dismantling steel post or struts, any section, embedded in concrete/ brick work/ masonry including taking out embedded portion and making good disturbed ground complete all as specified and directed.
S & F mild steel for posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.
S & F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm long and diameter of neck 5 to 10 mm complete all as specified and directed.
M & L for providing TMT bars mild steel bars 6 mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as stiffner of chainlink fencing complete all as specified and directed.
Supply only chain link fencing with 3mm dia galvanised steel wire, size of mesh 75mm x 75mm, weight exc 2.0 kg per sqm but n.exc 2.50 kg per sqm complete all as specified and directed.
Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed.
M & L for preperation of old decorative wall surfaces, ceiling cornices etc by using bio wash of approved make with jet spray; brooming and scrapping down dust particle, smoke soot, moulds, moss and efforescent salts etc, making surface smooth by applying ready mix putty where ever required and applying one coat of acrylic emulsion exterior paint of approved shade over a coat of primer including necessary scaffolding complete all as specified and directed.
M & L for preparation of new or previously untreated steel surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.
M & L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.
M & L for welding in repairs n. exc. 2.5 cm in length on metal of thickness exc. 6mm but n. exc 9mm complete all as specified and directed.
S & F in repairs galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. (each line wire to be measured) complete all as specified and directed.
Note: An amount of Rs 43555.05 on account of Credit Schedule for Schedule A Part II shall be deducted from the total amount of BOQ to arrive at Contract Sum.
S K ENTERPRISES (BID ID -3492982)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.24 MB
BOQ_828189.xls
BOQ • 0.45 MB
TenderPages.pdf
Tender Documents • 0.87 MB
Download all tender documents and submit your bid