Special repair and improvement works to the Ground floor, First floor and Second floor at Government Tourist Home in Uppalam, Puducherry.

Amount

Supplying chemical emulsion in sealed containers including delivery as specified - Chlorpyriphos / lindane emulsifiable concentrate of 20%.

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - tratment of soil under existing flooors using chemical emulsion @ one litre per hole, 300mm apart including drilling 12mm diametre holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor - with Chlorpyriphos / lindane E.C. 20% with 1% concentration.

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - Treatment of existing masonry using chemical emulsion @ one litre per hole at 300mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 ( 1 cement : 2 coarse sand) to the full depth of the hole - with chlorpyriphos / lindane E.C. 20% with 1% concentration.

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - treatment at points of contact of wood work by chemical emulsion Chlorpyriphos / Lindane ( in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6mm dia holes at downward angle of 45 degree at 150mm centre to centre and sealing the same.

Centering and shuttering including strutting, propping etc and removal of form for - Lintels, beams, plinth beams, girders, bressumers and catilevers.

Steel reinforcement for R.C.C.work including straightening, cutting, bending, placing in position and binding all complete above plinth level - Thermo - Mechanically Treated bars (ISI BRAND OF APPROVED MAKE) Fe - 415 or more.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level upto floor V level - cement mortar 1:3 (1 cement : 3 coarse sand)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part 1) decorative type, core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing plywood 4mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with - Decorative veneer facings of approved manufacture.

Providing and fixing 18 mm thick, 150mm wide pelmet of coir Veneer board ISI marked IS : 14842, including top cover of 6mm coir veneer board, nickle plated M.S.Pipe 20mm dia (heavy type) curtain rod with nickel plated brackets, including fixing with 25 X 3 mm M.S. flat 10 cm long fixed to pelmet with Padak wood cleats of size 100 mm X 40 mm X 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc, all complete.

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P.brass screws and wooden plugs, etc., wherever necessary complete - 20mm dia.

Providing 40 X 5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30 x10 x 15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing M.S.Piano hinges ISI marked IS : 3818 finished with nickel plating and fixing with necessary screws etc.complete - Overall width 65 mm.

Providing and fixing ISI marked powder coating sliding door bolts with nuts and screws etc.complte - 250 X 16 mm.

Providing and fixing ISI marked powder coating tower bolt black finish (Barrel type) with necessary screws etc.complete - 150x10mm.

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc complete - 40mm.

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc.complete - 125 X 64 x 2.50 mm.

Providing and fixing bright / matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete - 125 mm.

Providing and fixing bright / matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete - 100 mm.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) , of approved make (Jhonson / Asian / Somany / Nitco) in all colours, shades of size 300 x 450 mm as approved in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 300x450 mm.

Providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of first quality conforming to IS: 15622 of approved make (Nitco / Kajaria ) in all colours, shades, except white, ivory, grey, fume red brown laid on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying fully vitrified floor tiles of size 600 x600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make (Nitco / Rak / Johnson /Asian ) in all colours and shades , laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete - size of tile 600 x600 mm.

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes - 110 mm diameter.

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - Single tee with door - 110x110x110mm.

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - bend 87.5 degree - 110 mm bend.

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe.

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm.

6mm cement plaster of mix 1:3 (1 cement : 3 fine sand).

Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer.

Finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade - New work (two or more coats applied @1.43 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10sqm)

Wall painting with plastic emulsion paint - Royal of approved brand and manufacture to give an even shade - two or more coats on new work.

Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc complete.

Repair to plaster of thickness 12mm to 20mm in patches of area 2.5sqm and under including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead - of area 3 sqm and below.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - for thickness of tiles 10mm to 25mm.

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead - thickness above 25mm upto 40mm.

Dismantling aluminium / gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 metres lead.

Acid cleaning for the existing Mosaic floors , glazed tiles work and removing the stains and decays to give a glassy look etc complte (The Acid used shall be 32% concentrated hydrochloric acid after taking on the precautionary measures).

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32mm C.P.brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required - white vitreous china anglet back wash basin size 600x480 mm with single 15mm C.P. brass pillar tap.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved a) 15 mm nominal dia.

Providing and fixing 600x120x5 mm glass shelf with edges round off supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs etc., complete.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing - rectangular shape 453 x 357 mm.

Providing and fixing toilet paper holder - C.P.brass.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour - 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88mm, weighing not less than 170 gms.

Providing and fixing CP brass health faucet of approved quality - 15mm nominal bore

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand / make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flusing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect .

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall) - 20mm nominal outer dia pipes.

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall) - 25mm nominal outer dia pipes.

Providing and fixing G.I.pipes complete with G.I.fittings and clamps, including cutting and making good the walls etc - internal work -exposed on wall - 25mm dia nominal bore.

Providing and fixing brass bib cock of approved quality - 15mm nominal bore.

Providing and fixing ball valve (brass) of approved quality, high or low pressure, with plastic floats complete - 25mm nominal bore.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings (Glazing, paneling and dash fasteners to be paid for separately) - for fixed portion - anodised aluminium (anodised transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC 15).

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of : i) Ist course of applying cement slurry @ 4.4 kg /sqm mixed with water proofing compound conforming to IS : 2645 in recommended proportions including rounding off junction of vertical and horizontal surface - ii) II nd course of 20mm cement plaster 1:3 ( 1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface - iii) III rd course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area - iv) IV th course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100mm wide and pasted to each other with bitumen @1.7 kg/sqm).

Providing and fixing factory made single extruded WPC (Wood Polymer composite) solid door / window / Ceosetory windows and Other frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade) calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frames density of 750 kg / cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compresssive strength of 58N/sq.mm, modulus of elasticity 900 N/sq.mm and resistance to spread of flame of class A category with property of being termite / borer proof, water / moisture proof and fire retardant and fixed in position of with M.S hold fast/lugs /SS dash fasteners of required dia and length complete as per direction of Engineer-in-charge (M.S hold fast/lugs or SS dash fastners shall be paid for separately) Note: For WPC solid door / window frames, minus 5mm tolerance in dimensions i.e. depth and width of profile shall be acceptable. Variation in profile dimension on plus side shall be acceptable but no extra payments on this account shall be made. - Frame size 50 x 100 mm.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawl strength of 1800 N (Face) and 900 N (Edge), minimum compressive strength 50N/sq.mm, modulus of elasticity 850 N/sq.mm and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S.screws, all as per direction of Engineer-in-charge. (Note: Stainless steel butt hinges and necessary S.S.screws shall be paid separately) - 30mm thick.

Supplying of 3 star rated wall mountable Split type 1.5 ton capacity Air Conditioner unit (as per IS 1391 part 2) with following specification. Material for body for indoor unit ABS. Normal cooling capacity (K.cal./Hr): 5000 - 5500 power consumption max (watts): 1400 - 1500 watts, Min room discharge Air flow (CFM/Hr): 550 - 600. Air conditioner shall be suitable for 230V 50hz operation and capable of performing the function as cooling, air circulating and filtering and confirm to IS: 10617 part Carrier split A/C unit Model: NX series. The rate is inclusive of all taxes.

Supplying and fixing of 4 KVA Valtage stabilizer. Make: Microtek (Double booster) The rate is inclusive of all taxes.

Providing and fixing wall paneling to the required design and pattern with 18mm thick solid wood panel board (Rubber wood or equilvalent) with finger joint construction. The board with adhesive (Fevicol or equivalent) applied shall be fixed over the BWR grade plywood which is mounted over the frames of aluminium box and angle sections. The rate shall include the cost of solid wood panel board, labour charges, adhesives, transportation but excluding the cost as plywood, aluminium sections which will be paid separately all as directed by the Engineer-in-charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral staircases upto floor five level excluding cost of centering, shuttering, finishing and reinforcement with - 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).

Supply of 25 ltrs. Storage water heater Horizontal Make: Venus.

Providing cutting and fixing to required shape and design 19mm thick plywood (BWR) For cupboard & shutters/table top/ bottom/ sides/ furniture/ partitions and the like. The rate is inclusive of cost of materials, all taxes, wastages, screws, nails, fevicol SH, special labour charges for making cupboard & shutters/ furnitures and finishing the surface neat after fixing in required position as directed by the Engineer-in-charge.

Providing and fixing flat teak wood - I class reepers of size 20 x 6mm alround the edges of plywood. The rate is inclusive of cost of materials, watages, labour charges for fixing screws, nails, Fevicol SH and finishing the surface neat after fixing etc., complete as directed by the Engineer-in-charge.

Applying two coats of water proof acrylic modifier and bonding agent SETCRETE SB in the ratio 1:1 (1 setcrete SB : 1 water) including mixing with power mixer. Labour etc., complete.

Providing a layer of trowel applied cementitious water proofing membrane of 5mm thick nominal SETSEAL TANKING-A pre packed water proofing single part system over the SETSEAL APPLIED primer surface after wetting the surface including all complete.

Rectifying cracks in the brick panel wall of the existing building using ECOFIL -GP (crack filling mortar) @ 4.752 Kg/10RM mixed with water in the required proportion as per manufacturer recommendation . The rate inclusive of all costs for materials, labour for enlarging the crack using power cutter for 6mm width and 20mm deep grooves, cleaning the groove surface applying the crack filler and neatly finishing, scaffolding charges etc. complete as directed by the Engineer- in - charge.

Plastering the wall surface with cement mortar of mix 1:4 (One part of cement : 4 fine sand) mixed with rubber latex polymer classic acryfix SBR, a Primadon product or its equivalent at the rate of 1kg for 1 bag the specification of M/s Primadon Construction Products Pvt., Ltd and as directed by the Engineer-in-charge.

Naidu Engineering Works

B Akbar

D. PRITHIVIRAJ

E Gengadaran