KNMT 2023-24-Construction of Weekly Market Survey No 96 in Chinnamanur Municipality, Theni Dist

Amount

Earth work excavation for foundation and depositing on bank with in the initial lead of 10m and a lift of 2m in hard stiff clay, stiff block cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders etc. complete. complying with std. specifications.SS 20 B TNDSS No 23 & 24VI(S2) VII 9,10.Data-2023-24

Footing

Plinth Beam

Earth work excavation in all class of soils except hard rocks requiring blasting such as hard stift clay cotton hard earth shales murrams gravel stoney earth and earth mixed with small size with initial lead and lift including all incidential charges such as removing boulders sharing, strutting, watering bailing out water it necessary including all labour charges etc., Complete for foundation. .Data-23-24

Supplying and filling in foundation and basement with filling sand in layers of not more than 15 cm thick well rammed consolidated etc. complete complying with standard specification and as directed.Data-23-24

Cement Concrete 1:4:8 Mix (one part cement, four part sand and Eight part of aggrigate) using 40 mm size ISS HBG metal from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing. Laying and curing etc. complete. Complying with std. specifications.TNDSS NO 28 V, VI(S2) V, VI(S5A) VII.Data-2023-24

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.29mm height for plane surfaces in all floors with cross bracings using mild steel sheets of size 30cm x 55cm and 10 gauge stiffened welded with mild steel sheets of size 25mm x 25mm x 3mm for boarding and laid over silver oak (country wood). Joists of size 10cm x 6.5 cm dia spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre to centre etc complete complying with standard specification TNDSS No. 30 &86.Data-2023-24

A). For footing and Beam Work

b). For Column Below GL

c). For Slab

Drain

Vibrated Reinforced Cement Concrete 1:1½:3 Mix (One part cement, one and half part sand and three part of aggregate)using 20mm size ISS HBG metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing but excluding cost of reinforcement etc. Complete with std. Specifications.(using vibrater)(TNDSS No.30 V,VI (S3) VII-3.Data-2023-24

Up to GL

First Floor

Supplying fabricating and placing in position of TMT steel rods including cost of binding wire, cost of labour charges for fabrication and placing in position etc. Complete. Complying with std. specifications. TNDSS No,97 V,VI (S6) VII (S6) VII-3.Data-2023-24

Plain Cement Concrete 1:2:4 Mix (one part cement, Two part sand and Four part of aggrigate) using 20mm size ISS HBG metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications. TNDSS No.24.Data-2023-24

Brick Work in Cement Mortor 1:5 Mix (one cement, five sand) using best II Class Bricks of size 9 ” x 4 3/8 “x 2 3/4 ” from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.Data-2023-24

Supply and fixing of ISA equal angle for truss including cost of Material conveyance of all material, fabrication and fixing charges etc.Complete as per ISI with rust preventive primer & ready to assemble condition for easy installation at site including dismantling making necessary with power drill to the accessories such as supplying and fixing holdfasts, plastic bush inserts receiver runner bottom shock absorbers etc. Complete as Directed by the Departmental Officer. Data-2023-24

Plastering with cement mortar 1:5 mix to 12mm thick including cost and conveyance of all materials to site including curing etc.,complete as per standard specification.Data-2023-24

Plastering with cement mortar (1:4) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications (S.I.309).Data-23-24

Painting the new walls two coats over one coat of priming with best Emulsion paint of approved colour and quality including preparation of surface and finishing neatly etc., complete complying with standard specification and as directed by the department officers etc., complete complying with standard specifications. Data-2023-24

Painting Two coats for new iron work over existing priming coat using departmental approved colour & quality of ready mixed synthetic enamel paint, including cost of all materials, all labore charges, etc., complete. Data-2023-24

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers. Data-2023-24

Fabricating supplying and fixing of Polycarbonite sheets with the following specification. The materials should be of PGS tile profile with a Transperant colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dip+B307ped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.(Sor-2023-2024:Morth No:M-0718) Page No:34.

Supplying and erecting pull and push type rolling shutter with I.S.I. make of approved size and section using 18 gauge G.I.sheet with manually operated type. The Shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc, complete as per standard specification. .(Sor-2023-2024:Morth No:M-0401) Page No:58.

Supplying and fixing UPVC (Un-Plasticized PolyvinylChloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work.(Sor-2023-2024:Morth No:M-0675) Page No:80.

Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.Data-2023-24

Rubberised Interlocking Paver Block M40 grade providing and laying of 83 mm thick heigh strength type confiriming IS 15658 - 2006 of Rubberised Interlocking Paver Block in required size of mininmum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flumying bore pattern with approved nin - sticking surface in the top and the rate including levelling the base Stone dust cushion 100mm thick laying out the pavement cut the pieus to fit edge, vibrating pavers, sweeping transporting leading unloading as per standard specification.Data-2023-24

Supply and fixing of Horizontal Three Phase Distribution Board with MCBS AC supply suitable for both lighting and Motor Circuits including cost of conveyance of all materials to working site and all labour charge etc, complete complying with STD specification. SD 167

Wiring with 2 x 22/0.3mm PVC insulated multistrand copper conductor cable of 1100V grade in suitable PVC rigid pipe Open in wall and ceiling with PVC accessories in flush with wall and covered with hylum sheet of 3mm thick with TW switch box of 150mm x 100mm x 113mm for5 5A 3 pin nin-interlocking flush type CS plug with continuous earthwire connection of 14 SWG TC wire and making good of the Open portion with suitable colour for cealed plug point.SD 38

Supply and fixing of 3 Nos. 5A (3 pin and 2 pin) combined flush type wall socket with control switches Open in suitable TW box covered with hylem sheet in flush with wall with earth connection (for computer plug socket) (SD 139)

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable heavy gauge MS conduit pipe Open in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the Open portion with suitable colour (SD - 43)

Provision for 25W LED Focus Light for Outer Passage Which includes all cost and Conveyance and Labour Charges etc,. Complete.(Sor-2023-24M-1295)Page No:131.

Supply and fixing of GI steel tubular pole for street light of 6 Metre Length Single Bracket Pole with Base Plate (250 x 250 x 6mm) 76.10mm OD x 3.65mm Thick x 6000mm Length etc., complete.(Sor-2023-24M-M-2118)Page No:168.

Supply and fixing of 30 watts LED out door street light fitting with LED etc., complete(Sor-2023-24M-M-1296)Page No:131.

Drilling of New Borewell (150mm dia) in hardrock area etc complete as per standard specifications.

Drilling of 150 mm dia borewell up to casing pipe.

Drilling of 150mm dia bore well beyond casing pipe

Supply and delivery of PVC (ISI) Casing pipe suitable for 150 mm dia bore well including cost and labour charges etc. complete as per standard specifications.

supply and delivery of PVC (ISI) Casing

Labour charges for inserting casing pipes assembly (With slot or without slot) in the drilled hole including welding the joint etc., complete and supplying and packing the annular space with pebbles of size and quality as approved by the Executive Enginee

Labour charges for inserting casing pipes

Supply and delivery of 10 HP (50 lpm x 275 m ) 3 phase submersible pumpset suitable for 150mm dia borewell of accessories as per standard specifications.

10 HP (50 lpm x 250 m )

Supply and delivery of 10 HP III-Phase panel board D.O.L.with two level guard and auto start as per standard specifications.

10 HP III-Phase panel board

Supply and delivery of 11/2" (40mm) GI Pipe including cost, conveyance labour charges for erection etc., complete.(inside the bore)

11/2"(40mm) GI Pipe

Supply and delivery of 4 sqmm. cable PVC insulated and sheathed 3 core flat type copper cable confirming to IS 694/1990 including labour charges etc., complete and as directed by the departmental officers.SOR 2023-24-17 Pg-120.

4 sq.mm cable (Double layer)

Labour charges for the erection of Horizontal shaft, centrifugal pumpset (coupled/Monoblock) in bore well / Open well including fixing of suction pipe and foot valve upto a maximum depth of 7 meters and delivery pipes to the required length with valves,

10HP Submersibe motor

Supply and delivery of following G.I.Pipe and specials including cost and conveyance etc., complete as per standard specifications.

11/2" (40mm) GI Elbow

11/2" (40mm) GI Coupling

8" MS bore end cap

2" MS Clamp set

Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Supply of water supply materials including cost and conveyance etc, complete.

4" PVC Pipe

4" PVC Bend

4" PVC Elbow

4" PVC Tee

4" PVC Coupling

Lowering PVC rigid pipes, specails to trench and laying to proper grade and alignment jointing with PVC couplers with cement paste and testing to the required pressure including conveyance of water for filling during testing.

4" PVC Pipe

Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the Departmental Officers. (Sor-2023-24M-0774)Page No:95.