Office Furniture to be installed at DRC Gladni Narwal and SCADA Panama Chowk Jammu.

Amount

Workstation table in completely knock down conditions with an overall size 750mm X900mm X 1200mm that is to be assembled at site. The worktop shall have the size 1200mm X 600mm for individual seating system made up of 25mm thick medium density fibre board of IS 14587-1998 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. A pullout keyboard trey shall be provided of 18mm thick medium density fibre board having size 525mm X 350mm. The trey shall be operated on keyboard channel. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in the front side of user as well as on the both sides of the user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with 40-60µ thick. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways & 4 ways (L-cover for corner, T-cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) and marker board provided at front of the user. Laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. Fixed type pedestal shall be provided with an overall size 400mm X 450mm X 725mm. The pedestal shall be made up of medium density fibre board of IS 15512(2004)pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized lock with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A nylon castor based CPU unit shall be provided with an overall size 468mm X 284mm with 18mm thick medium density fibre boardd.The work station shall have 6 no.s socket 5/13 amp universal socket with 10 amp DP MCB,ethernet communication socket(RJ 45),Telephone jack(RJ11),Fan 90 CFM 4"X4" wire as per rating. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015; ISO-45001:2018, ISO-50001:2011; BIFMA membership and AIOTA certification.

Mid back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood upholstered with high resilience moulded polyurethane foam 50mm thick having density 50kg/m³ with fabric tapestry 0.6mm thick and 235 GSM and the back shall be made of metal bright bar upholstered with breathable mesh tapestry. The backrest of the chair shall be made by keeping the natural curvature of the spine with cushion base lumbar support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used injection moulded polypropylene loop arm completely joint with seat. For seating durability the chair shall have push back 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged injection moulded in 30% glass filled black nylon having pitch circle Dia. 650 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 460±10 mm(W) X 455±10 mm(D) and back size shall be 550±10 mm(H) from seat & overall height = 990±10 mm.

Printer table in completely knock down conditions with an overall size 750mm X 750mm X 600mm that is to be assembled at site. The worktop shall be made up of25mm thick medium density fibre board of IS 14587-1998 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on 18mm thick curve shape cut gable end with shelf and bottom made ofmedium density fibre board of IS 14587-1998. The table shall consists of 2 no.s socket 5/13 amp universal socket with 10 amp DP MCB,ethernet communication socket(RJ 45),Telephone jack(RJ11), wire as per ratingThe manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015; ISO 45001:2018; ISO 50001:2011; BIFMA membership and AIOTA certification.

Steel almirah. The overall size of the Almirah shall be 900mm (W) X 450mm (D) X 1830mm (H). The Almirah shall be supplied with 2 nos. of glass door and 2 nos. of steel door with adjustable shelves. The door shall be operated with aesthetically appealing snap fit ABS plastic handle and concealed crank hinge. The glass shall be used 4mm thick clear. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength. The entire body panel, shelf shall be made of high yield strength 0.8mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. To protect the ball from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-60µ thick.

Conference table in completely knock down conditions with an overall size 3000mm X 1200mm X 750mm that is to be assembled at site. The table top shall be made up of back to back 25mm thick medium density fibre board of IS 14587-1998 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The worktop shall be supplied with flapper box which have several components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. The raceway or metal wire carrier shall be situated below the worktop as per requirement of inlaying the electrical management and carrying the wire horizontally. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 25mm thick medium density fibre board of IS 14587-1998 and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. The modesty panel shall be 18mm thick medium density fibre board of IS 14587-1998 with appropriate PVC edge banding connected with both end. The table shall be supported over SS pipe leg of 202 grade. Table with 2 nos. pop-up box for electrical and data point access. It shall have cross-section area 80mm X 20mm. There shall be buffers provided to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015; ISO 45001:2018; ISO 50001:2011; BIFMA membership and AIOTA certification.

Mid back chair. The seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam having density 40kg/m³ and the back shall be made of metal insert MS frame padded with high resilience polyurethane foam having density 32kg/m³. The same shall be upholstered with leatherite tapestry 1mm thick and 571 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine with lumbar support. The seat and back shall be arrested together with powder coated HR steel spine and the armrest shall be used fixed PP arm completely joint with seat. For seating duraility the chair shall have synchro tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged injection moulded in 30% glass filled black nylon having pitch circle Dia. 700 mm fitted with 5 nos. twin wheel castor. The castor of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 440±10 mm (D) X 465±10 mm (W) and back size shall be 440±10 mm (W) X 480±10 mm (H) from seat. Overall height shall be = 950±10 mm, base width/ depth = 760±10 mm.

Modular table in completely knock down conditions with an overall size 1650mm X 1650mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall have the size 1800mm X 750mm made up of 25mmmedium density fibre board of IS 14587-1998with approved laminate and finish as per approved shade. The profile shall be in rectangle shape with front and back full round post form edges and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The table top shall be supported over medium density fibre board of IS 14587-1998 base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick medium density fibre board of IS 14587-1998with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table shall have side unit for storage purpose with an overall size 900mm X 450mm X 750mm. The side unit shall be made up of medium density fibre board of IS 14587-1998 with top 25mm thick and other parts 18mm thick like shutter, back, side panel etc. It shall have 2 sliding shutter which slides over sliding rail track. The shutter shall be operated with SS handle and Multi-purpose (MP) locking mechanism. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 680mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. A movable type CPU unit shall be provided with an overall size 468mm X 284mm. The CPU unit shall be made up of 18mm thick Pre-laminated particle board and mounted over 65mm injection moulded nylon castor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015; ISO 45001:2018; ISO 50001:2011; BIFMA membership and AIOTA certification.

High back chair. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ and 25mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine as well as head support. Moulded PP arm shall be used with cushion and leatherite upholstery. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suite them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged made up of injection moulded in 30% glass filled black nylon having pitch circle Dia. 700 mm fitted with 5 nos. twin wheel castors, the castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 515±10mm(W) X 490±10mm(D) and back size shall be 510±10 (W) X 650±10mm(H) from seat & overall height = 1110±10mm.

Modular table in completely knock down conditions with an overall size 1500mm X 1650mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The worktop shall have the size 1500mm X 750mm made up of 25mm thick medium density fibre board of IS 14587-1998 with approved laminate and finish as per approved shade. The side top shall have the size 900mm X 450mm X 750mm with 25mm thickmedium density fibre board of IS 14587-1998. The table top profile shall be in rectangle shape with one side round and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board. The trey shall be operated on keyboard channel. The table top and side top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick medium density fibre board of IS 14587-1998 with appropriate PVC edge banding connected with both end. There shall be buffers provided at the bottom to avoid scratches on the floor. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 680mm. The pedestal shall be made up of medium density fibre board of IS 14587-1998. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. A movable type CPU unit shall be provided. It should be made up of 18mm thick particle board. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Conference table in completely knock down conditions with an overall size 3600mm X 1200mm X 750mm that is to be assembled at site. The table top shall be made up of back to back 25mm thick medium density fibre board of IS 14587-1998 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The worktop shall be supplied with flapper box which have several components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. The raceway or metal wire carrier shall be situated below the worktop as per requirement of inlaying the electrical management and carrying the wire horizontally. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 25mm thick medium density fibre board of IS 14587-1998 and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. The modesty panel shall be 18mm thick medium density fibre board of IS 14587-1998 with appropriate PVC edge banding connected with both end. The table shall be supported over SS pipe leg of 202 grade. Table with 2 nos. pop-up box for electrical and data point access. It shall have cross-section area 80mm X 20mm. There shall be buffers provided to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015; ISO 45001:2018; ISO 50001:2011; BIFMA membership and AIOTA certification.

Steel almirah in perfectly upright and straight position. The overall size of the almirah shall be 915mm (W) X 485mm (D) X 1980mm (H) including legs. It should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. Door shall be made of 1mm thick and all other components shall be made of 0.8mm thick high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. Stiffeners shall be provided in shelf & door. The steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity per each shelf shall be 40kg maximum. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 40-60µ.

Reception table in completely knock down conditions with an overall size 2400mm X 700mm X 1000mm that is to be assembled at site. The worktop shall have the combination of 18mm thick medium density fibre board of IS 14587-1998 with approved laminate and shade as top and and 25mm thick Medium density fibre-board with deco painted as base top with aesthetically grooves. The upper top shelf shall be made up of 25mm thick medium density fibre board of IS 14587-1998. It should be supported on 25mm thick medium density fibre board of IS 14587-1998 base vertical panel. The table profile shall be in curved shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick medium density fibre board of IS 14587-1998 having size 550mm X 280mm. The trey shall be operated on sliding channel. The table shall be clad with 1mm thick modesty panel which provide structural support for the table. It should be 1mm thick CRCA with perforated sheet duly powder coated connected with both end. The main top shall be supported on SS peg at front which mounted on the fixed pedestal and 4 nos. of legs made up of MDF board having cross-section area 100mm X 100mm. Fixed pedestal shall be provided with an overall size 400mm X 500mm X 610mm. The pedestal shall be made up ofmedium density fibre board of IS 14587-1998. Pedestal side, back, facia shall be 18mm thick & drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer having same size. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel to enable smooth movement. The drawer shall be synchronized locked with central locking mechanism by one single key. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The structure shall be upholstered with leatherite tapestry 1±0.2 mm thick. The understructure shall consist of pipe frame leg of SS having cross-section area 30mm X 30mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 1540±10 mm(W), seat height = 420±10 mm, overall width = 1800±10 mm, overall depth = 760±10 mm & overall height = 800±10 mm.

Center table with an overall size 600mm X 600mm X 450mm. The top shall be made up of 12mm thick toughened glass. The top profile shall be in square shape with bevelled edges. The understructure shall consist of MS/CRCA rectangle pipe frame having cross-section area 30mm X 15mm with 1.6mm thick duly powder coated with 40-60µ dry film thickness.

Center table with an overall size 1200mm X 600mm X 450mm. The top of the table shall be made up of 12mm thick toughened glass. The top profile shall be in rectangle shape and the edges shall be in chamfer shape. The top shall be supported on 50mm dia. Aluminium round spacer with 15mm thick situated over SS 202 grade pipe frame. The under structure shall consist of SS with shiny chrome finish pipe frame having cross-section area 67mm X 13.5mm. There shall be PPCP shoe provided to avoid scratches on the floor.

HXWXD=385mmx507mmx491mm,designed to with stand fire for upto 90 minutes,2 key locks,tongue and groove construction to prevent hot gases/smoke from seeping in,locking option,one electronic combination lock,certified and listed at SP,Sweden and UL,USA,flexibility of horizontal/vertical models in FR safes 30 ltr.

International Gas Agency

urban interiors