8155/21-22/E8PROVN OF CHAIN LINK FENCE 650 M AT KIARI AND OTHER SANCTIONED WORKS AT NYOMA UNDER GE 860 EWS

Amount

Excavating in post holes (or similar holes) in hard/dense soil each n.exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n. exc 50m and making good surface compete all as specified and directed by Engr-in-Charge.

M&L Cement Concrete type C2 1:3:6 (40mm graded aggregate) in foundations, post hole, filling and mass concrete etc complete all as specified and directed by Engr-in-Charge.

S&F of mild steel work in angle iron or other stock section or core for wooden hand - rail straight portioon, drilled and countersunk for balusters, nosing of steps, including embeding in concrete and screwing etc. wind ties for foof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe – 290 Gde E -165 complete all as specified and directed by Engr-in-Charge.

S&F 4mm dia galvanised steel wire, 100x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position including closing after filling complete all as specified and directed by Engr-in-Charge.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed by Engr-in-Charge.

M & L for MS round bars Fe-410-W (Gde E-250) quality A or Fe 290 (Gde-E-165) 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

Preparation of new steel and iron surfaces of any description over 10cm in width or girth , priming with a coat of red oxide primer and applying two coats of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

S&F for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm and n.exc 10cm long with dia of the neck 5 to 10mm complete all as specified and as directed by Engineer-in-Charge.

M&L framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks complete all as specified and directed by Engr-in-Charge.

Rendering 15mm thick in cement mortar 1:4 using water proofing compound as per manufacturer's instruction in two layers, finished even and smooth surface without using extra cement - External Plaster (WPC measured and paid separately) complete all as specified and directed.

Supply only liquid water proofing compound for external plaster complete all as specified and directed by Engr-in-Charge.

M&L for preparing new surfaces including priming plastered and other surfaces with priming paint and applying two coat of cement base paint complete all as specified and directed by Engr-in-Charge.

Excavation in trenches n.exc 1.5mtr wide and n.exc 1.5m depth and n.exc 10 Sqm on plan and getting out in any kind of soil complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (Nominal mix) using 40mm graded stone aggregate as in foundation filling and similar work complete all as specified and directed by Engr-in-Charge.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete etc complete.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M & L for TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

Formwork to sides of rough finished surface of concrete square, rectangular or polygonal pillars, posts, struts, piers, columns and stanchions complete all as specified and directed by Engr-in-Charge.

M&L for providing RCC 1:1.5:3 type B-1 using 20mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns and similar work complete all as specified and directed.

M&L for providing RCC 1:1.5:3 type B-1 using 20mm graded crushed stone aggregate as in columns, pillars, piers, post and struts or similar work complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of concrete surfaces and finished even and smooth without using extra cement complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm.complete all as specified and directed.

Removing excavated material n.exc. 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M & L for Preparing new plastered surfaces of walls and applying two coats of cement base paint, all as specified .

M&L framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks complete all as specified and directed.

Preparation of new steel and iron surfaces of any description over 10cm in width or girth , priming with a coat of red oxide primer and applying two coats of synthetic enamel paint complete all as spd

M&L for walling of randowm rubble, uncoursed, well bonded, bedded and solidly hearted, built in Cement mortar 1:6 complete all as spd & directed.

M&L for Pre-cast cement concrete block masonry Type C-1 (1:3:6) 20 mm graded aggregate with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L 75 mm thick Cement concrete type D- 2, 1:4:8 (40mm graded crushed stone aggregate) as in sub base as specified and directed.

M&L for 40mm thick Cement concrete type B-1, 1:2:4 (20mm graded crushed stone aggregate) as top layer finishing cement concrete surface even and smooth using extra cement as specified and directed.

M&L for colour Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick rendering in cement mortar 1:4 as specified and directed.

M & L for coloured non-skid ceramic tiles 400x400x7 mm thick in flooring set & jointed in neat cement slurry and pointed in cloured cement to match the shade of tiles over and including 15 mm thick cement mortar screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed by Engr-in-charge.

M&L for preparing newly plastered surface of wall and applying two coat of white wash complete all as specified and directed.

S&F 0.56 mm Galvanised, Plain Aluminium sheeting Alloy 31000 H4 in sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 . fixed with L-type or J-type or cranked hook bolts in lieu of screw as spd and directed.

M&L for preparation of new or previously untreated wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as spd.

Surface dressing n.exc 15 cm deep in soft/loose soil complete all as specified and directed.

Hardcore of gauge n exc. 63mm deposited spread and levelled in layers not exc 15cm thick watered and rammed to a true surface with brick stone boulders complete all as specified and directed.

S&F 2nd class hardwood , plain, solid, straight chowkats and frames, wrought , framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints & fixing with shutter, etc complete all spd & directed.

S&F 2 class clean swan timber hardwood in scantling fixed as specified and directed.

S&F factory made 30mm thick second class hard wood plain framed paneled shutters (two panels) with lock rail and panels of 9mm BWP commercial ply or 12 mm veneered particle board for others with commercial veneering on both faces and size of members of doors shutter as per IS 1003(part-I) as specified in SSR part -I section 3 clause 8.20 (a) fitted to chowkats, kiln seasoned and chemically pressure treated complete all as specified and directed by Engr-in-Charge

S & F 4 mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F 200 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed by Engr-in-Charge.

S&F 150 mm size aluminium handle cast type complete all as specified and directed by Engr-in-Charge.

S&F 150 mm size aluminium anodised barrel tower bolt complete all as specified and directed by Engr-in-Charge.

S&F 125 mm long butt hinges medium weight , cold rolled mild steel and fixed as spd and directed.

M&L for 75 mm thick cement concrete type C2, 1:3:6 (40 mm graded aggregate) as in plinth protection complete all as specified and directed by Engr-in-Charge.

S&F Vitreous China wash down water closet pan (pedestal pattern) white and trap, including connection to drain (or outgoing pipe) and to flushing pipe complete all as specified and directed by Engr-in-Charge.

S&F 500 Ltrs capacity Rotaional moulded, polythene water storage tanks (cylindrical shape with vertical threaded top closed) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 20mm bore all as specified in SSR Part I complete all as specified and directed by Engr-in-Charge.

S&F 15 mm dia bib tap chromium plated with cruth butterfly handle, screw down , screwed for iron pipe or brass ferrule complete all as specified and directed by Engr-in-Charge.

S&F 75 mm dia PVC (SWR) pipe single socketed in any length with rubber ring joints, laid in trenches or fixed to wall complete as spd and directed.

S&F 75 mm dia PVC (SWR) bends any radius complete as spd and directed.

S&F 75 mm dia PVC floor trap , plain with grating including jointing with solvent cement complete all as spd and directed.

S&F Wash basins, Vitreous China size 550 x 400mm (flat back or angle back type)any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply including brackets, as spd and directed.

S&F 32 mm bore waste pipe Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls,or in floors, as spd and directed.

S&F Pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15 mm bore and fixed, as spd and directed.

S&FStop valves 15 mm chromium plated fancy type caste copper alloy,screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed , as spd and directed.

S &F 16 mm dia 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN-16) UN stablized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches etc. complete all as specified and directed.

S&F15 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed as spd and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm as spd and directed.

S&F PVC (SWR) pipes of 110mm bore single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed by Engr-in-Charge.

M & L Plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 110 mm bore PVC pipe complete all as specified.

Excavation over areas n.exc 1.5m deep and and getting out in hard/dense soil complete all as specified and directed.

Excavation over areas exc 1.5m deep and n.exc 3.00 m deep and getting out in hard/dense soil complete all as specified and directed.

M&L for walling of randowm rubble, uncoursed, well bonded, laid dry in retaining walls, abutments and similar work complete all as specified and directed by Engr-in-Charge.

Supply only integral water proofing compound complete all as specified and directed.

M&L for PCC (1:3:6) type C1 (using 20 mm graded crushed stone aggregate) as in coping including necessary form work complete all as specified and directed.

M & L for Reinforced cement concrete (design mix) M-25 in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete, all as spd.

M&L for precast RCC type B-1, 1:2:4 using (20 mm graded aggtrgate) as in cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces all as specified and directed.

M & L for Mild steel round bars 10mm dia and over, cut to length, bent to shape required, as in MS rungs complete all as specified and directed.

Formwork to flat soffits of suspended slabs such as roof slabs, floors slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surfaces complete all as specified and directed .

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roof n.exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20 cm wide complete all as specified and directed.

M & L for PCC Type B-1 1:2:4 using 20 mm graded stone aggregate) as in haunching benching and PCC coping incl necessary formwork and set in cement motar 1:4 complete all as specified and directed.

M & L for broken boulder stone n.exc 63 mm of gauge in loose filling complete all as specified and directed.

M&L for point wiring (Concealed type) for one light point or one fan point controlled by one way, single pole switch complete with PVC insulated, unsheathed stranded copper conductor (multistrand) of size 1.5 sqmm, 1100 volts grade conforming to IS 694 /90, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly and supply and fixing rigid non matalic ISI marked PVC conduit pipe medium grade of size not less than 20 mm dia alongwith all accessories and fittings such as bends, tees, elbow etc, juction boxes incluidng sunk terminal boxes, new 3 mm thick laminated sheet cover with brass screw and cup washers with all accessoires and incl cutting and chasing work on brick walll not exceeding 10 cm girth and making good to distrubed surfaces with cement mortar 1:3 and treated surface with wihte/colour wash/OBD/plastic paint to match with existing surface complete all as specified and directed

S&F switch piano flush button single pole one way 5 Amps complete all as specified and directed by Engineer-in-Charge

S&F angular lamp holder, PVC/Polycaronate type with back plate suitable for 9 watt LED bulb for batten fittings complete all as specified and directed by Engineer-in-Charge

S&F LED 9 Watt complete all as specified and directed by Engineer-in-Charge

S&F celing rose, surface back light, 65 x 50 mm three terminals complete all as specified and directed by Engineer-in-Charge

S&F 20W 6000K LED batten with suitable LED tube light fitting and making connection to ceiling rose by 23/0.0076 copper flexible wire complete all as specified and directed by Engineer-in-Charge

S&F in replacement of Distribution Board, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed.

S&F MCB single pole and neutral 35 to 60 Amps, 240 Volt, 10 KA complete all as specified and directed by Engineer-in-Charge

S&F MCB single pole 5 to 30 Amps, 240 Volt, 10 KA complete all as specified and directed by Engineer-in-Charge

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore (7.5 m long) including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR 2009 Part-I and connecting to CBDB’s as specified or indicated including testing on completion.

Supply and fix exhaust fan made of study Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed.

Supply and laying XLPE insulated armoured heavy duty electric cable with aluminium conductor (Stranded) 1100V grade cross-sectional area 16 Sqmm 2 core laid in trenches or passing through pipe or fixed on pole etc complete all as specified and directed by Engr-in-Charge

M&L for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40 mm thick complete all as specified and directed by Engineer-in-Charge

M & L sand cushioning to underground cable complete all as specified in clause 19.75 of SSR Part - I.

M/S MA CONSTRUCTION Co

M/S GEE AAR and SONS ENTERPRISES

M/S LIBE & CO

M/S Behl Sons

Rampal Singh Contractor

BETONG BUILDERS

M/S STANZIN NOBROO