SPL REPAIR TO BLDG NO P-368(SINGLE OFFRS ACCN) AND PROVN OF 01 X TOILET BLOCK UNDER AGE B/R- V AND AGE E/M -V OF GE (N) BATHINDA AT BATHINDA MIL STN

Amount

B/R Works

Dismantling brick/PCC terracing tiles single layer in roof laid and pointed in cement mortar and removing/disposal off from the site complete all as specified and as directed by Engineer-in-charge.

Demolition of mud in roofs, any thickness, including plastering and leaping (whether full thickness removed or only a part there of) including removing/cutting uprooting grass, vegetations and roots of small plants etc on roof floor and surrounding/parapit wall etc, including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for Roughening surfaces of existing concrete surfaces of roof by picking , sweeping , clean and washing down with water to remove dust etc and brushing with neat cement slurry @ 3.0 Kg of cement per Sqm complete all as specified and directed by Engineer-in-charge. Note: The rate of neat cement slurry @ 3.0 Kg of cement per Sqm is included in this item and nothing shall be paid extra on this account.

Material and labou for cement concrete (1:2:4) type B-0, using 12.50 mm graded stone aggregates as in roof padding including mixing with Water Proof Compound as per manufacturer's instructions and finished even and fair complete all as specified and as directed by Engineeer-in-charge. Note :- Water Proof Compound shall be measured and paid for separately under respective item of Schedule'A' BoQ.

Material and Labour for 15 mm thick screed bed or bedding layer in cement mortar (1:4) on roof surfaces, parapet or vertical beam surface (horizontal or vertical) finishing the surfaces even and fair complete all as specified and as directed by Engineer-in- charge.

Supply only liquid water prrofing compound ISI marked

Material and labour for tack coat layer of blown grade bitumen of any penetration applied hot @ 1.70 Kg per Sqm and priming the surface @ 0.30 Kg per Sqm and with and including material and labour for laying 3mm thick APP based polymer membrane of weighing not less than 3.5 Kg per Sqm reinforced with polyster non woven fabric (weight not less than 150 Gm per Sqm) laid on primed surface at by torch application with side overlap 75mm and end overlap 100mm and tucked into the chasesas a treatment for moderate condition complete all as specified and as directed by the Engineer-in-Charge. Note: The rate of 3mm thick APP based polymer membrane is included in this item and nothing shall be paid extra on this account.

Material and labour for PCC (1:2:4) Type B0 using 12.5mm graded stone aggregate as in roof kerb (golla) or mud stops, side of roof sheet & similar work etc rounded or chamfered on edges including necessary form work etc complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, in any description including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by Engineer-in-charge.

Material and labour for brick work with sub class ‘B’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge.

Taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for rendering/plastering appx 10mm thick (matching with existing plaster thickness) in cement mortar (1:3) on any face of ceiling in patches matching with existing, finished fair and even and smooth without using extra cement, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering/plastering appx 15mm thick (matching with existing plaster thickness) in cement mortar (1:6) on old brick or concrete surfaces of walls/pillars /cornices in patches matching with existing, finished even and smooth without using extra cement, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering/plastering 15mm thick in cement mortar (1:4) on any face of Brick walls or concrete surfaces (external surface), finished even and smooth without using extra cement, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparing newly plastered or concrete surface of ceiling by sand papering or by the other mean and after preparing the surfaces and applying two coat of olil bound distemper with (paint brush /with roller ) complete all as specified & directed by Engineer-in- charge

Material and labour for Preparation of old decorated surfaces (plastered/unplastered) of ceiling by remove / scraping down all loose particle, smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean including applying 2mm thick wall care putty to make the surface smooth and glossy upto the entire satisfaction of Engineer -in-Charge and after reparing the surface smooth applying two coat of olil bound distemper with roller only complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of New plastered/ concrete surface of wall/Pillars/cornices by brooming down with using broom/sand papering or by other means, and preparing the surfaces smooth by applying 2mm thick wall care putty to make the surface smooth by using sander machine (with provision of dust sucking) upto entire satisfaction of Engr-in-Charge and after preparing the surface applying two coats of plastic emulsion paint (with roller brush ) complete all as specified and as directed by Engineer-in-Charge.

Matterial and labour for complete removal of existing treatment (any layers of existing treatment) and efflorescence from Old decorated surface of wall/ pillars/ cornices by scraping down with using Mechanical sander machine (including provision of dust sucking) upto entire satisfaction of Engineer-in-Charge brooming down and preparing the surfaces smooth and make good by applying 2mm thick wall care puty with white cement based and make the surface even and smooth upto entire satisfaction of Engineer -in-Charge and after that appplying two coat of plastic emulsion paint (with roller brush only) complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of Newly plastered/ concrete surface of wall/Pillars/cornices by brooming down with using broom/sand preparing or by tany other means, and preparing the surfaces smooth by appling one coat of primer and applying one coat of 2mm thick wall care putty to make the surface even and smooth by using sander Machine (With provision of dust sucking) upto entire satisfaction of Engineer-in-Charge and after preparing the surface applying three coats of acrylic smooth exterior emulsion paint, as approved tint/colour by using paint roller brush complete all as specified and directed by Engineer-in-Charge.

Material and labour for complete removal of existing treatment (any layers of existing treatment ) effloresence from old decorated surface of wall/pillars/cormices by scraping down with using Mechanical sander machine( including provision of dust sucking) upto entire satisfaction of Engineer-in-Charge brooming down and preparing the surfaces and after that applying two coats of acrylic smooth exterior emulsion paint as approved tint/colour by using paint roller brush only complete all as specified and directed by Engineer-in-Charge.

Dismantling of floor hearth or wall tilling including cement mortar bedding but not backing including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for vitrified ceramic coloured tiles (light shade) 10 mm thick square or rectangular area of each tile not exceeding 0.36 sqm, as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for vitrified ceramic coloured tiles (light shade) 10mm thick square or rectangular (same as floor tile, as per above item ), as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick bedding layer (rendering) in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Material and labour for Non Skid ceramic coloured tiles 7 to 8 mm thick square or rectangular area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for Glazed ceramic coloured tiles of size 350mmx 250mm / 450mmX 350mm/ 450mmX 300mm, 7mm to 8mm thick, as in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick (Av thickness) bedding layer (rendering) in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge.

Demolition stone/marble slabs of any description or thickness as in floors/ cooking platform/steps etc. laid bedded and pointed in any mortar including removing rubbish material from the site complete all as specified and as directed by Engineer-in-charge.

Material and labour 18-20mm thick machine cut, granite duly factory grinding and polished (table rubbed and polished) of approved colour for counter sunk wash basin, plateform/cooking plateform or as directed, including screed bed 15mm thick in cement mortar (1:4) (grey cement slurry) including pointing in white cement (1:2) using marble dust with admiture of pigment to match with shade of granite stone slab including cutting as required including cleaning and extra polishing if required complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 18-20mm thick any of black/mahroon colour of marble work other than (table rubbed and polished) as in counter sunk wash basin, steps, jambs, pillars, windowcills, cooking platforms and like, set and including screed bed 15mm thick in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admiture of pigment to match with shade of marble slab, including machine cutting to make it square or rectangular or as per site requirement including cleaning and extra polishing if required, complete all as specified and as directed by Engineer-in-Charge.

All as per item No 28 above but as in skirting/dado/riser etc including 10mm thick rendering in Cement mortar (1:4) all as specified and directed by Engr-in-Charge

Material and labour for moulding the edges half round on exposed side (Rounding to edges of stone slabs one edge) of granite/marble as in kitchen shelf, cooking platform WHB counter, steps and other similar situations etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:3:6) type C0 using 12.5mm graded aggregate as in back filling of chowkats and for hold fast complete all as specified and directed by Engineer-in-Charge.

Material and labour cutting holes in brick walls in cement mortar for inserting holdfast and making good dismantled portion in cement mortar 1:3 or cement mortar 1:2:4 type B1 using not exc half brick walls depth embeddded portion of holdfast or lugs for coller stand, measured from the faces jamb into walls complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floor and above ground floors and paving not exceeding 15cm thickness below or above ground level of any description and in any position including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and directed by Engineer-in-Charge.

Material and labour for 75mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in flooring, hard standing, sub base, plinth protection/path etc. finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for machine pressed precast interlocking paver block 60 mm thick with grey cement and no pigment, factory made, any shape and size, conforming to IS 15658-2006, made out of M-35 grade concrete laid over and including 25 mm thick layer of sand cushioning complete all as specified and as directed by Engineer-in- charge. Note: The rate of 25mm thick layer of sand cushioning is included in this item and nothing shall be paid extra on this account.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames, wooden/PVC doors/steel ventilator) area not exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4 Sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge.

Supply and fixing factory made 105 x 60mm pressed steel frames, thickness of sheet 1.25mm for doors with one or more rebates including supply and fixing necessary lugs and lock strike plate, etc. , including fixing butt hinges suitable Nos as directed for each leaf, complete all as specified and as directed by Engineer-in- charge. Note : - (i) Butt hinges shall be measured and paid separately under appropriate item of BOQ.

Supply & fixing factory made plain framed panelled shutters (two panels as approved), 35mm thick of 2nd class hard wood with lock rail and panel inserts of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I), kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401, including 2nd class soft wood kail beading 20mm wide tapering from 10mm to 5mm on one side and also fitted to chowkhat complete all as specified and as directed by Engineer-in- charge. Note : - (i) The sutters shall be brought at site without primer and same shall be applying at site as per direction of Engineer-in-charge. Primer shall be measured paid separately under appropriate item (painting) of BOQ.

Supply & fixing factory made glazed and skeleton shutter, 35mm thick of 2nd class hard wood open rebated (two panels as approved) and prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc. Sizes of members as specified in SSR Part-I, Section 8 and fitted to chowkhats, menbers shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and as directed by Engineer-in- charge. Note : - (i) The sutters shall be brought at site without primer and same shall be applying at site as per direction of Engineer-in-charge. Primer shall be measured paid separately under appropriate item of BOQ.

Supply and fixed solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed by Engineer-in-Charge.

Supply and fixed factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 100mm long powder coated mild steel butt hinges medium weight cold rolled complete all as specified & directed by Engineer-in-charge.

Supply and fixing anodised aluminium handle cast type 125mm long complete all as specified & directed by Engineer-in-charge.

Supply and fixing anodised aluminium handle cast type 150mm long complete all as specified & directed by Engineer-in-charge.

Supply and fixing aluminium anodised barrel tower bolt of extruded section, 200mm long complete all as specified & directed by Engineer-in-charge.

Supply and fixing aluminium anodised barrel tower bolt of extruded section, 150mm long complete all as specified & directed by Engineer-in-charge.

Supply & fixing aluminium anodised sliding door bolts 250mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed by Engineer-in- charge.

Supply & fixing powder coated aluminium anodised frame, made out of aluminium section / aluminium chanel, powder coated (minimum thickness of powder coating not less than 50 micron), for doors, windows, ventilators with one or more rebate including jointing cleat for fixing etc. including taking down old unserviceable frame complete all as specified and as directed by Engineer-in-Charge. Note :- Weight of aluminium section/aluminium channel shall be physically ascertained through a board of officers convened by Accepting officer and payment shall be made only after the actual weight at site.

Supply & fixing anodised powder coated aluminium shutter for window /Ventilator/ door made out of aluminium section weighing 0.55 Kg/mtr, powder coated (minimum thickness of powder coating not less than 50 micron) including aluminium hardware i.e. necessary joining cleats, glazing clips, rubber neoprene packing, suitable size of aluminium handles 2 Nos and aluminium hinges 04 Nos in each leaf (size of handle and hinge as directed), anodised aluminium snap beading, screws etc including fixing of glass, complete all as specified and directed by Engineer-in-Charge. Note :- (i) Aluminium chowkhat frame shall be measured and paid separately under appropriate item of BOQ as supply and fixing. (ii) Glass and other filling material in panels shall be measured and paid separately under appropriate item of BOQ.

Material and labour for mild steel work conforming to Fe-290 (Gde E-165) as in grills, gratings etc. with ends of bars shouldered and/ or rivetted or forged into spikes; framed guard bars, walkways, railing, framed work of water tanks and similar works complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 5.5mm thick tinted sheet glass ordinary quality/figured glass pin head in squares not exceeding 0.5sqm in each pane and fixed with oil putty etc. as required or as directed complete all as specified & directed by Engineer-in- charge.

Supply & fixing aluminium (extruded section) body door closer hydraulically regulated, designation No 3, universal type suitable for door shutter of 851 to 1000mm in width and weight between 61 to 80 Kg, ISI marked complete all as specified & directed by Engineer-in-charge.

S&F mild steel 300mm long rat tail rod pattern spring including roller and roller plate and fixing to wooden frame with screw complete all as specified and directed by Engineer-in-Charge.

S&F Floor door stoper (150mm) of aluminiuk alloy body and tngue, anodised , with hard drawn steel spring fixed in floor complete all as specified and directed by Engineer-in-Charge.

Supply & fixing galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tack or galvanised wire staples complete all as specified & directed by Engineer-in- charge.

Material and labour for Preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed by Engineer-in- charge.

Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed by Engineer-in- charge.

Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in first floor, ground floor, sunken portion and paving at any thickness below or above floor level of any description and in any position including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for sunken treatment to sunken floor, cleaning the surface by wire brush, rendering to floor and sides with 10mm thick in cement mortar (1:3) including mixing of liquid WPC in mortar @ 200ml per bag of cement of 50kg, finished even and smooth without using extra cement, after that material & labour providing two coat of two components (one part liquid two part powder) ready to use cementitious water proofing coating on properly prepared surface by brushing having elongation of > 50% for the applying water proofing treatment on horizontal and vertical surfaces of sunken floor, complete all as specified and as directed by Engineer-in-charge. NOTE:- (i) Applying 1st coat of two components modified polymer coating. (ii) Provn of glass fiber mess of 2mm x 2mm immediately on alone coating. (iii) Apply 2nd coat of two components modified polymer coating after 72 Hrs on horizontal and vertical surfaces.

Material and labour for 25mm thick cement concrete (1:2:4), type B-0 using 12.5 mm graded stone aggregate as in floor, sunken floor etc, finished rough to receive tiles, including mixing of liquid WPC in mortar @ 200ml per bag of cement of 50kg, complete all as specified and as directed by the Engineer-in-Charge. (Note :- WPC shall be measured & paid separately as Supply only)

Material and labour for rendering/plastering 15mm thick in cement mortar (1:4) on any face of Brick walls or concrete surfaces including mixing of liquid WPC in mortar @ 200ml per bag of cement of 50kg, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. Note :- Water proofing compound shall be measured & paid separately as Supply only

Material and labour for applying one coats of Dr fixit pidecrte in sunken floor portion of toilets and bathrooms chajja stair case etc by using of 1 to 2 Sqm and applying by brush etc, complete all as specified and directed by Engr-in-Charge.

Material & Labour for PCC (1:5:10) type E-2 using 40mm graded stone aggregate as loose filling of sunken floors complete all as specified and as directed by Engineer-in-charge.

Material & Labour for 100 mm bore cast iron soil waste and vent pipe (spun pipe ) in any length with or without ears, fixed to wall with stack clamps (interval of 1m) made out of FI 50x5mm and 16mm dia round iron stay and jointing with cement mortar including dismantling/taking down/out old pipe complete all as specified and as directed by Engineer-in- charge.

Material & Labour for 100 mm bore cast iron soil waste and vent pipe (spun pipe ) in any length with or without ears, laid on floor/trenches and jointing with cement mortar including dismantling/taking down/out old pipe complete all as specified and as directed by Engineer-in- charge.

Material & Labour for 75 mm bore cast iron soil waste and vent pipe (spun pipe ) in any length with or without ears, fixed to wall with stack clamps (interval of 1m) made out of FI 50x5mm and 16mm dia round iron stay and jointing with cement mortar including dismantling/taking down/out old pipe complete all as specified and as directed by Engineer-in- charge.

Material & Labour for 75 mm bore cast iron soil waste and vent pipe (spun pipe ) in any length with or without ears, laid on floor and jointing with cement mortar including dismantling/taking down/out old pipe complete all as specified and as directed by Engineer-in- charge.

Material & Labour for 100 mm dia cast iron floor trap with CP grating including jointing to waste pipe with solvent fixed in cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate including taking out old floor trap complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 75 mm dia cast iron floor trap with CP grating including jointing to waste pipe with solvent fixed in cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate including taking out old floor trap complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement 100mm bore cast iron bends (any radius)/elbo, diminishing pieces or tapers (larger bore measured) with oval access door fixed with cement joints complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in replacement 75mm bore cast iron bends (any radius)/elbo, diminishing pieces or tapers (larger bore measured) with oval access door fixed with cement joints complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in replacement 100mm bore CI branch pieces single (equal or unequal), ordinary or inverted (Spigot or socket type) or with parallel branch fitted with oval access door as specified & directed by Engineer-in- charge.

Supply & fixing in replacement 75mm bore CI branch pieces single (equal or unequal), ordinary or inverted (Spigot or socket type) or with parallel branch fitted with oval access door as specified & directed by Engineer-in- charge.

Supply and fixing 100mm bore cast iron traps, 'P' & 'S' complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 100mm bore cast iron cowl complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 75mm bore cast iron cowl complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints for drain or rain water fixed along walls with stack clamps made out of FI 50x5mm and 16mm dia round iron stay (interval of 1m) including nut bolt and PCC work, including dismantling/taking down old pipe complete all as specified and as directed by Engineer-in- charge.

Supply & fixing PVC (SWR) bends (any radius) suitable for 110mm bore pipe fixed to walls or laid in floor complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 110mm bore PVC (SWR) 'Y'/'T' junction (double/ single ), equal or unequal (any radius) suitable pipe fixed to walls or laid in floor complete all as specified and as directed by Engineer-in- charge.

Supply and fixing stainless steel plate rack standred of min size 750mm x900mm fixing with steel screw and complete all as necessary items complete all as specified.

Taking up or down existing galvanised steel water tubing (GI pipe) 15mm bore including fitting/connection from wall/ceiling/floor/concealed etc. including removing from site/keeping aside for reuse (serviceable as good condition as directed) complete all as specified and as directed by Engineer-in-charge.

Taking up or down existing galvanised steel water tubing (GI pipe) 20mm bore including fitting/connection from wall/ceiling/floor/concealed etc. including removing from site/keeping aside for reuse (serviceable as good condition as directed) complete all as specified and as directed by Engineer-in-charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 15mm bore with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor or concealed in walls including cutting chases in wall (as required) and making good disturbed surfaces of walls including cutting and threading of existing pipe any dia for insertaion of tee branch including hole in wall to pass the pipe out side for connection as per site requirment complete all as specified and as directed by Engineer-in- charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 20mm bore with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor or concealed in walls including cutting chases in wall (as required) and making good disturbed surfaces of walls including cutting and threading of existing pipe any dia for insertaion of tee branch including hole in wall to pass the pipe out side for connection as per site requirment complete all as specified and as directed by Engineer-in- charge.

Supply and fixing in repair vitreous china Wash down water closet (One piece EWC ) including flushing cistern, seat cover, jet spray, PVC connection and with all necessary assembly/fittings and connection to drain (or outgoing pipe) complete all as specified and directed by Engineer-in-Charge

Supply and fixing vitreous china (white) wash hand basin (WHB) Oval type table top fancy type including 32mm dia CP waste coupling, waste pipe, PVC connection and all necessary fittings complete all as specified and directed by Engr-in-Charge

Supply & fixing stainless steel sink made out of 1.00mm thick sheet, overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm, kitchen or laboratory with plugs, washers, waste pipe including bedding in cement mortar, fixing in existing space or fixing with cast iron cantilever brackets and connecting union to waste pipe, including taking down old unserviceable sink including fixing to granite/marble stone complete all as specified and directed by Engineer-in-Charge.

Dismantling/taking down of existing unserviceable PVC water storage tanks capacity exc. 500 litre but not exc. 1000 litre complete all as specified and as directed by Engineer-in-charge.

Supply & fixing rotational moulded polyethylene water storage tank white colour of capacity 1000 litres (cylindrical vertical, triple layered with closed top), hoisted and fixed in position including making inlet and out let connection and including ball valve and gate valve, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing chromium plated toilet paper holder complete fixed to wall complete all as specified.

Supply & fixing in replacement 600 mm long PVC connection 15mm size with PTMT nuts complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement bib tap long body cast copper alloy, chromium plated fancy type, with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply & fixing CP Mixer valve 15mm bore, brass (cast copper alloy) chromium plated, mixer for mixing hot & cold water suitable for WHB/Wall/Sink , screwed down for iron pipe 15mm bore complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of mixer valve shall be as given in SSR or in relevant IS.

Supply & fixing in replacement hand shower (health faucet) ABS body including 1 meter long 8mm dia flexible tube and including wall hook including taking down old any type shower complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Glass sheet assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement stop valve/angle valve cast copper alloy, chromium plated fancy type screwed down high pressure with crutch or butterfly handle, screwed both ends suitable for 15mm bore iron pipe complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve/stop cock/angle valve shall be as given in SSR or in relevant IS.

Supply and fixing in replacement concealed stop cock cast copper alloy, chromium plated, fancy type, long shank and cup, screwed both ends suitable for 15mm bore iron pipe complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve/stop cock shall be as given in SSR or in relevant IS.

Supply & fixing in replacement cromium plated shower rose 125mm size, with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed by Engineer-in-charge.

Supply & fixing in replacement gun metal, globe or gate valve (ISI marked), brass cast copper alloy, with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of gate valve shall be as given in SSR or in relevant IS.

Supply & fixing in replacement gun metal, globe or gate valve (ISI marked), brass cast copper alloy, with iron wheel head, screwed both ends suitable for 15mm bore iron pipes complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of gate valve shall be as given in SSR or in relevant IS.

Supply and fixing CP grating doom 125mm dia with/without waste hole (min weight 40gms) complete all as specified and directed by Engineer-in-Charge.

Supply & fixing 19mm internal dia MS pipe with PVC coated drapery rod (Curtain Rod) of approved make including fenials and brackets for door and window including taking down old curtain rod and palmet box complete all as specified and directed by Engineer-in-Charge.

Supply & fixing MS cromium plated, soap tray approximate 160mm, including fixing to wall with CP screws and PVC plug complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches in soft / loose soil not exceeding 1.5 metre wide & not exceeding 1.5 metre in depth for foundations of manholes, sewerage pipe lines etc including getting out complete all as specified and as directed by Engineer-in-Charge .

Demolition and breaking up drain pipes SGSW, AC or reinforced concrete pipe upto and including 150 mm bore pipes, complete all as specified and directed by Engineer-in-Charge.

Material & labour for PCC 1:3:6 type C-2 using 40 mm graded stone aggregate to drain pipe including packing under & haunching against the sides of pipe 250 mm dia ( internal) after they are laid and tested in trenches, complete all as specified and directed by Engineer-in-Charge.

Material & labour for 250 mm dia ( internal) Reinforced concrete pipes, class NP2, laid and jointed complete with collars laid in trenches & jointed, complete all as specified and as directed by Engineer-in-Charge .

Material & labour for cement concrete 1:3:6 type C-2 using 40 mm graded crushed stone aggregate for foundations, fillings & mass concrete, sub base, plinth protection, complete all as specified and as directed by Engineer-in-charge.

Material & labour for cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate for manhole benching, flooring and coping, complete all as specified and as directed by Engineer-in-charge.

Supply & fixing SFRC (Steel fibre reinforced concrete) cover and frame (heavy duty HD-20 grade designation) size of cover 0.70 x 0.70 conferming to IS 12592, fixed in cement cocrete 1:2:4, complete all as specified and directed by Engineer-inCharge.

Returning and filling including spreading, leveling watering and well ramming in layers not exceeding 25cm thick in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Removing excavated material (surplus soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-charge.

Material and labour cutting into existing Manholes/septic tank for connecting new drain upto 150mm internal dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round to 3/4 section) in cement concrete (1:2:4) type B1 using finished and reforming benching as required complete all as specified and directed by Engineer-in-Charge.

Material and labour for 18 mm thick MDF board prelaminated MDF board , exterier grade (grade-1) confirming IS 14587, fixed with screws for kitchen cupboard and cabinet ,self for cupboard including cut edges of prelaminated board to be sealed with 6mm teak lipping and all necessary fittings including dismantling of board of any description and type complete all as specified and directed by Engineer-in-Charge.

Material and labour for 12 mm thick prelaminated partical board interior grade prelaminated both side with decorative choice lamination fixed with screw to timber frame work/aluminium frame work including dismantling of board of any size and type complete all as specified and directed by Engineer-in-Charge.

S&F 30mm wide Continuous (piano) hinges, mild steel, bright finish or electrogalvanised fixing to wooden frame complete all as specified and directed by Engineer-in-Charge.

S&F 100mm long fency type Stainless steel handles, cast type, polished bright complete all as specified and directed by Engineer-in-Charge.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of Brass, bright finished complete all as specified and directed by Engineer-in-Charge.

Demolition of RCC as in roof slabs (other than ground floors), beams, stair case, landing, chajjas, and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engineer-in-Charge.

M & L for RCC 1:2:4 Type B0 (12.5mm graded stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge. Note:- (Reinforcement will be measured and paid for separately)

M & L for RCC 1:2:4 Type B0 (12.5mm graded stone aggregates) as in fins, fascias, louvers, parapets, and railings exc. 60cm in height, balustrade, and the like complete all as specified and directed by Engineer-in-Charge. Note :- (Reinforcement will be measured and paid for separately)

Material and Labour for Use and waste of form work to sides and soffits of floor or roof beams, roof slabs, cantilevers, shelves etc and similar items rough finished surface complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Use and waste of form work to sides and soffits of fins, louvers, fascia and similar items rough finished surface complete all as specified complete all as specified and directed by Engineer-in-Charge.

Supply and fixing mild steel TMT bars 10 mm dia , and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to Fe 410-W, Gde E-250 complete all as specified and directed by Engineer-in-Charge.

All as per ser item No.128 here-in-before but 6 to 8mm dia complete all as specified and directed by Engr-in-Charge.

All as per ser item No.128 here-in-before but 5mm and upto and including 10 mm dia in stirrups, spacess and binders complete all as specified.

M&L for rough cast plastering including 15 mm thick rendering in cement plaster 1 :4 complete as specified in SSR Part-I clause 14.22 as given .Note : Rough cast finish : After applying under coat of cement mortar 1:3 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg. which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1 shall be applied complete including taking down cement lime plaster and applying two coats of cement based paint over a coat of primerall as specified and as directed by the Engineer-in-Charge.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/ loose soil including cutting of grass, roots, bushes if any and filling of lower portion with soil obtained from cutting and dressing complete all as specified and as directed by Engineer-in-charge.

Material and labour for PCC ( 1:4:8), type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed by Engineer-in-charge.

Material and labour for brick work with sub class ‘B’ old size burnt clay bricks, straight or curved on plan to any radius in half brick walls built in CM (1:4), etc; complete all as specified and as directed by Engineer-in-charge.

Material and labour for 40 mm thick damp proof course in cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate) to horizontal or vertical surfaces including necessary form work and including mixing of liquid WPC in mortar @ 200ml per bag of cement of 50kg, complete all as specified and as directed by Engineer-in- charge. Note :- WPC shall be measured & paid separately as Supply only)

Material and labour for reinforced cement concrete (1:2:4) (nominal mix) type B-1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns landing, balconies, canopies, deck slabs and in shelves, lintel over 1.5m and the like complete all as specified and as directed by Engineer-in-Charge. Note:- Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and Labour for mild steel work in tubular trusses, tubular/rectangular MS pipe such as vertical post, trusses, rafter, purlins etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws complete all as specified and as directed by Engineer-in-charge.

Supply and fixing anodised aluminium snap grid frame work of size of grid 605mm x 605mm for false ceiling including necessary notching and prepared holes, the snap grid shall consist of anodised aluminium main tee of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/RM, cross and Intermediate tee of size 23.5mm x 26.4mm x 1.4mm weighing 0.191 Kg/RM. The main and cross tee shall be jointed at junction with steel screws or MS bolts, nuts and washers, the snap grid (main / cross tee sections) shall be supported at ends all along the wall with anodised aluminium angle of size 35mm x25mmx 2mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and duly suspended with 4mm GI wire hangers (upto 1200 mm length) adjusting level fixed to roof slab by means of ceiling cleats made of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including providing 12mm thick gypsum board in grid fixed in false ceiling grid made of aluminium as per above specifications complete all as specified and as directed by Engineer-in-charge.

Supply & fixing, factory made steel window confirming to IS 1038 with side hung shutters including projecting type hinges, with steel handle, steel peg stay, complete, dovetailed welded, with one shop coat of zinc chromate primer with glazing bars including fixing of lugs in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) complete all as specified & as directed by Engineer-in- charge.

Supply and fixing 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed by Engineer-in-charge.

Material and labour for 75mm thick cement concrete ( 1:4:8), type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 10 litres capacity PVC valveless syphonic action type low level flushing cistern (white colour) with inlet, ball valve, float, handle including brackets and 32mm dia PVC flush pipe, PVC Connection 450 mm long with PTMT nuts suitable for 15mm bore pipe complete all as specified and directed by Engineer-in-Charge.

Supply and fixing vitreous china (white) squatting pan 'Orissa' pattern, white, size 580 x 440 mm, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flush pipe, anti-syphonic pipe etc including making good to floor and including trap set, in and including material and labour for lime concrete with 40mm graded stone aggregate with lime mortar 1:3 complete all as specified and as directed by Engineer-in-charge.

Supply & fixing vitreous china wash basin, white, oval type 550mm x 400mm, including 32mm chromium plated waste coupling and PVC waste pipe including bracket and cutting for and pinning in end of bracket or erecting including fixing only pillar tap (new or serviceable old pillar tap as per site condition ) complete all as specified and as directed by Engineer-in-Charge. (Note :- Pillar tap if required in replacement, shall be measured & paid separately as Supply only under appropriate item of BOQ.)

Supply and fixing vitreous china bowl type Urinal, flat back type of size 465 mm x 355mm x 265mm, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and pointing around urinal back in cement, grating and union for discharge etc. complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement incuding waste pipe and coupling and angle valve complete all as specified and as directed by Engineer-in-charge.

Material and labour for preparation of new plastered surfaces of walls/pillars /cornices by brooming down with using broom/sand papering or by any other mean, washing down with water and applying two coats of cement base paint as per approved tint/colour by using paint brush complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing bib tap cast copper alloy, chromium plated with crutch or butterfly handle with capstan head, wall flange, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing stop valve/angle valve cast copper alloy, fancy type, chromium plated with crutch or butterfly handle, screwed down, screwed both end for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixed pillar tap cast copper alloy with capstan head, chromium plated, fancy type, high pressure with or without letter 'Hot' or 'Cold' with long shank and fly nuts screwed for iron pipe or for brass ferrule 15mm bore complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS

Supply and fixing low density polythene (LDPE) pipe of pressure rating 6kg/Sqcm, 32 mm bore for waste pipe of wash basin etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Salt-glazed stoneware gully traps of size 150mm x150mm, square or round mouthed, type 'S' including squre chromium plated 150 mm dia grating complete all as specified and directed by Engineer-in-Charge.

Material and labour for Hardcore of gauge n exc. 63 mm of Broken stone or boulders , deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surfacecomplete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing tubular towel rail brass chromium plated 20 mm dia ‘D’ type 60 cm long including end brackets complete all as specified and as directed by Engineer-in-charge.

Supply & fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints for drain or rain water fixed along walls with stack clamps made out of FI 50x5mm and 16mm dia round iron stay (interval of 1m) including nut bolt and PCC work, complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 110mm bore PVC (SWR) P traps laid in trenches or in floors complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 110mm bore PVC (SWR) vent cowl complete all as specified and as directed by Engineer-in- charge.

Material and labour for cement concrete (1:4:8), type D2 using 40mm graded stone aggregate as in bed of drain pipe of size upto 150mm bore (internal) including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed by Engineer-in- charge.

Material and labour for 150mm bore (internal dia) salt glazed stone ware (SGSW) drain pipe, grade ‘A’, laid on concrete bed to required slope in trenches, jointing with packed spun yarn and in cement and sand mortar (1:1) and tested complete all as specified and directed by Engineer-in-Charge. (Note : Excavation, earrh work and concrete bed shall be measured and paid separately under appropriate item of BOQ.)

E/M Works

Taking down old unsv copper/ aluminium point/ submain wiring concealed / batten (light, fan, socket or power/submain) complete, including fixture and fittings such as switches, sockets, ceiling roses,bell push,bell electric,lamp holder,bulk head fitting, pendants, regulators, sockets, light fitting and any type switch board wooden/iron,round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

Taking down old and unserviceable, distribution board any type including , MCBs etc after removing all connection and make good the disturbed surface all as directed by Engr-in-charge.

M&L in replacement for Sub main wiring with proper colour coding , insulated , unsheathed , multistranded ,copper conductor FRLS, cable of 2 run 6 Sqrmm for phase and neutral and one run of 4.0 Sqrmm for earth wire unsheathed , miltistranded , copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length. Note : Wiring shall be done in proper colour coding.

M&L for point wiring for one light/fan/5 Amps independent socket point/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into an including new concealed PVC rigid/steel conduit 1.8mm wall thickness ISI marked terminated into CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified. Note : (a) wiring shall be done by using proper colour coding (b) Earth wire shall be of green colour (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clips all as directed by Engr-in-Charge.

All as per item No 166.00 above but for multi 5 pin 5 amp socket outlet on same board

All as per item No 166.00 above but for multi 5 pin socket outlet 5 amp socket on independent board

All as per item No 166.00 above but for One bell/buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5 Sq. mm size.

All as per item No 166.00 above but for multi 6 pin 15 7mp socket outlet independent controlled by 15 Amp switch with 2.5 sqmm copper conductor multistrand cable pvc insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 20/25 mm dia and unsteathed copper conductor multistrand cable 1.5 sqmm as earth wire FRLS pvc insulated in green color all as directed by engr-in-charge.complete with new CI/pressed steel sunken black with hylum top sheet cover 3mm thick.

S & F Socket outlet 5 Pin, 5A, flush type complete all as directed

S&F angle/batten lamp holder on PVC square Blocks with PVC insulated body complete all as directed

M& L in replacement Self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K Complete all as directed.

S&F for switch piano, flush type single pole one way 5 Amp, 240 volts all as specified .

S&F for switch piano, flush type single pole two way 5 Amp, 240 volts all as specified .

S & F for bell push , flush type single pole , 5 Amp, 240 volts all as specified .

M&L switch piano flush button single pole one way 15 Amp all as specified

M&L socket outlet 6 pin 15 Amp 240 volt multi purpose flush typeall as specified

S&F of calling bell Ding Dong/buzzer AC 230 Volts, single pole.

S&F of stepped type electronic fan regulator flush type on the existing phenolic laminated sheet.

Supply and fixing in provision of BLDC (Brushless direct current motor) ceiling fan 5 star rated, complete with blades, down rods, and accessories, 230 Volts, 1200mm sweep, Min air delivery 210 CFM with service value 6.00 BEE, including electrical connection providing twin core round copper conductor cable of suitable size, complete all as specified and as directed by Engineer-in-Charge. Note :- (i) Srl Number of ceiling fan and 'GE North BTD' shall also be writing on fan with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account, Srl number will be issued by Engineer-in-Charge. (ii) Ceiling fan installed/hanging at site as directed by Engineer-in-charge (from market to AGE E/M store/AGE E/M store to sites /Location, all conditions will be the responsibility of contractor and nothing extra will be admissible on this account

M&L distribution board sheet steel phosphatised powder coated for MCB with copper bus bar and neutral link earthing stud SPN 12 way 240 volts double door complete all as directed by Engr-in-Charge.

S&F ceiling rose, 3 Phase/PVC/polycarbonate isolated body

S&F in replacement new generation energy saving ,wall mounted LED Tube light batten fittings , extruded aluminum heat sink provided for efficient heat dissipation & integrated electronic driver 20 Watt LED duly fitted on pvc square block 6500K (4' ft long ) with LED rod 20 watt, 230 Volts 50 Hz.

S&F MCB single pole and Neutral 32 Amp suitable for 240 volt.

S&F MCB single pole and Neutral 40-50 Amp suitable for 240 volt.

S&F MCB single pole 5-32 Amp suitable for 240 volt.

S&F in replacement MCCB 4 pole, 415 Volt fixed thermal and fixed maganatic setting of cap 125 Amps 16 KA

S&F of Vertical Distribution Board (TP&N) 4 way double door suitable for MCCB 125 Amp 16 KA four pole as incomer and out going MCBs and should be IP 43 protected with Copper BusBars, Neutral Links, Earthing bar all as specified and directed.

Material and labour for Earthing complete with galvanised iron earth plate electrode of size 60cm x 60cm x 6.3mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including earth continuity GI wire 4 mm (upto test point from earth plate i.e. 7.5m min) by means of GI bolts/nuts/washers and including protected by 15mm dia GI light grade protection pipe from earth plate to test point, including making of test point. Earth plate shall be surrounded by packed layer of char coal/coke & salt all around bottom and top with alternative layer. 20mm GI light grade pipe for watering (should be 10cm above GL) and including socket, plug, funnel, wire mesh, RCC cover and (including steel for cover) PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in earthing pit including necessary form work, excavation & earth work, all as specified & shown in electrical plate No. 3 of SSR (Part – I) including taking out/dismantling old unserviceable earthing system complete all as directed by Engineer-in-charge. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner.

Material and labour for Earthing complete with galvanised iron earth plate electrode of size 60cm x 60cm x 6.3mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including earth continuity GI wire 4 mm (upto test point from earth plate i.e. 7.5m min) by means of GI bolts/nuts/washers and including protected by 15mm dia GI light grade protection pipe from earth plate to test point, including making of test point. Earth plate shall be surrounded by packed layer of char coal/coke & salt all around bottom and top with alternative layer. 20mm GI light grade pipe for watering (should be 10cm above GL) and including socket, plug, funnel, wire mesh, RCC cover and (including steel for cover) PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in earthing pit including necessary form work, excavation & earth work, all as specified & shown in electrical plate No. 3 of SSR (Part – I) complete all as directed by Engineer-in-charge. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete

M & L for LED Mirror light fitting of 9/10 watt, 6000 K , lineer & compact with decorative grey end caps,polycarbonate body and ribbed opal diffuser complete with lamp and all other accessories fitting arrangement including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector all as specified and directed.

Making holes for 300 mm dia exhaust fan of suitable shape & size into or through brick walls at groung/First/Scond floor including plastering for making good to the original surfaces of any description disturbed including painting /distemper matching with the existing colour. Note : Rates are deems to be including charges of any type of T&P, Insurance of staff deployed at site.

Supply and fixing of exhaust fan steel body 300 mm sweep (BEE, 5 star rated) with louvres, 230V, single phase AC supply, hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface as per existing surfaces, and connection to fan with suitable flexible twin core round copper wire complete all as specified and directed by Engineer-in-Charge. Note :- (i) Srl Number of exhaust fan and 'GE North BTD' shall also be writing on fan with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account, Srl number will be issued by Engineer-in-Charge. (ii) Exhaust fan installed/hanging at site as directed by Engineer-in-charge (from market to AGE E/M store/AGE E/M store to sites /Location, all conditions will be the responsibility of contractor and nothing extra will be admissible on this account

Supply and fixing in provision of storage type water heater (Geyser) electrical operated 230/240 Volts 25 ltr capacity, BEE 5 star rated complete with all safety equipment and accessories such as safety valve, thermostat, plug top, etc. required for proper functionality & including electric/earth connections complete all as specified and directed by Engineer-in-Charge. Note :- (i) Srl Number of Gyeser and 'GE North BTD' shall also be writing on Gyeser with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account, Srl number will be issued by Engineer-in-Charge. (ii) Gyeser installed at site as directed by Engineer-in-charge (from market to AGE E/M store/AGE E/M store to sites /Location, all conditions will be the responsibility of contractor and nothing extra will be admissible on this account.

Labor for fixing of 4 Nos rawl plug of suitable size (4"-6") nuts & bolts, grouting work in RCC/Brick wall, cemented works labour charges for cutting to exisiting GI pipe line of size 15 mm dia in position for insertion of tee or branch connection jointing complete with necessary GI fittngs, plumbing work all as per site requirement.

Supply and fixing (concealed in wall or as directed) single pole and neutral sheet metal enclosure (Geyser Box) with a two pin and earth plug and socket complete with one single pole MCB of capacity 25 Amps, 240 volts, AC supply complete all as specified and directed by Engineer-in-Charge.

M & L for replacement of tubing GI "Medium grade" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 15 mm dia complete all as specified and directed.

S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed for 15 mm dia of pipe.

S&F PVC connection of size 15 mm dia with PTMT nuts of length 450 mm long (hot series braded, threaded and cold series) complete all as directed by Engr-in-Charge.

S&F Bib tape cast copper alloy with crutch or butterfly handle screwed down , screwed for iron pipe for brass ferrule of size 15 mm bore.

Labor for cutting to existing GI pipe of size 25/20 mm dia in position for addition/alteration or insertion of TEE for branch connection complete with cutting, threading and jointing/fixing including GI fitting as per site requirement.

S&L and testing cable XLPE Insulated screened PVC bedded galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 V grade cross sectional area 16 Sqmm, 2 core in and incl taking out old one all as specified and directed.

S&L and testing cable XLPE Insulated screened PVC bedded galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 V grade cross sectional area 70 Sqmm, 3.5 core in and incl taking out old one all as specified and directed.

M&LSand filling in cushing bed of cable and consolidation complete as specified

Supply and laying comman burnt clay building sub class `B' bricks, laid over sand Cushioning laid at right angle along with cable, all as specified and as directed.

S&L GI tubing light grade, 40 mm bore incl all accessories for encasing cables for mechanical protection, laid under plinth/floors/path culverts with complete accessories such as bends/sockets/reducers/saddles incl necessary threading/drilling works all as specified and directed of sizes (MS work will be measured under separate item in schedule).

S&F Lamp holder PVC/polycarbonate type with back plate suitable for batten fitting with LED bulb 9W

S & F wall mounted LED fitting 1 x 20 watt,6000k, 4 ft complete with retro LED tube and batten, environment friendly , energy efficient complete with all fittings connections all as specified and directed.

S &F New generation energy saving & environmental friendly long life versatile pressure die -cast aluminium IP 66 roadway luminaire with high power LED of 25/35 watt with toughened glass complete with suitable GI for security light fitting fixing to wall/column & electrical connection to the light fitting providing 1.5 mtr long twin core round copper conductor cable of suitable size and testing complete all as specified and directed.

S&F in replacement of sheet metal encousers made out of CRCA mild steel sheet, double door, powder coated DB SPN 8 way 240 Volt, 200 AMP rated bus bar, dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified.

M&L for sub main wiring complete with two single core 6 sqmm, 1100 volts grade PVC insulated, multistranded copper conductor FRLSH cable (ISI marked) in and including PVC concealed conduit (medium quality ISI marked) and cutting of chases in wall including 6 sqmm single core copper earth wire to common earth and connecting to earth dolly complete all as specified.

M/s DHEERAJ JAIN CONSTRUCTION COMPANY

M K Enterprises

Singla Enterprises

K L JINDAL AND CO.

SAPNA BUILDERS

V K CONTRACTOR

Ajay Enterprises