Spl repair to STP No 1,2,3 under AGE B/R (P-1) at Faridkot Mil Stn

Amount

Dismantling posts or struts (wood, steel or RCC) of any section, including taking out embedded portion in concrete, brick work etc and making good the disturbed ground complete all as specified and directed .

Dismantling fencing wire mesh, barbed wire ,any type complete all as specified and directed .

Excavation in trenches in soft/loose soil not exceeding 1.5m deep and 1.5m wide, for foundation etc or manholes,piers,shafts etc not exceeding 10 Sqm on plan and getting out complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in foundations, filling and mass concrete complete all as specified and directed .

M&L for Reinforced cement concrete M 25 (Design Mix) (using 20 mm graded crushed stone aggregates) as in foundation including rafts, footings, foundation beams, plinth beams, bases of columns etc complete all as specified and directed .

M&L for Reinforced cement concrete M 25 (Design Mix) (using 20 mm graded crushed stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed .

M&L for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter, for rough finished surfaces of concrete all as specified and directed.

M&L for use and waste of form work to sides of pillars,struts,piers and columns square/rectangular for rough finished surfaces complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape as required, including cranking, bending and binding with & including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed ..

M&L for brick work with fly ash bricks, straight or curved on plan exceeding 6 metre mean radius, built in cement mortar 1:6 complete all as specified and directed .

M&L for 5mm thick rough cast plaster over and including 10mm thick rendering in cement mortar 1:4 on fair faces of brick or concrete surface complete all as specified and directed Note : The rough cast mixture shall consist of crushed stone / fine gravel aggregate, coarse sand & cement in the ratio of 1:1:1 over the rendering coat.

S&F mild steel work for making Y at the top of brick wall including cutting tops to shape as directed, drilling holes, notching for wire etc,including all necessary drilling, bolting or riveting,welding etc and similar works conforming to Fe-290 Gde E-165 quality complete all as specified and directed

S&F mild steel work as in angle iron post using angle iron as per existing size for making Y in the existing swan neck post including cutting tops to shape as directed, drilling holes, notching for wire etc,including all necessary drilling, bolting or riveting,welding etc and similar works conforming to Fe-290 Gde E-165 quality complete all as specified and directed

S&F galvanised,2strand,steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossings with and provision of galvanised mild steel wire,staples or steel pins etc. complete all as specified and directed .

M&L for punched tape concertina coil, 450mm diameter ,06 metre openable length,having 50 Nos round per 06 metre, tied with angle iron post with necessary bolts,concertina coil of core wire diameter 2.5mm,blade thickness 0.5mm,blade length 12mm,width of blade 15mm and spacing of blade 26mm complete all as manufacturer and directed . Note: The weight of concertina coil shall be ascertained by BOO as ordered by GE and payment shall be made accordingly and contractor shall have no claim on this account.

M&L for preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed .

M&L for Framed work as in doors or gates etc of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing using Fe 290 (Gde-E-165) complete. complete all as specified and directed .

Dismantling of plain or corrugated steel/fibre glass sheeting, any gauge in roof covering complete all as specified and directed .

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as specified and directed .

S&F Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as specified and directed .

M&L for hard core of gauge not exceeding 63mm using broken stone or boulders, deposited, spread and leveled in layers not exc 15cm thick, watered and rolled/rammed to a true surfaces complete all as specified and directed .

M&L for sand filling under floor 25mm thick with washed and screened dry fine river sand including watering, well ramming and consolidation complete all as specified and directed .

S&F Machine pressed precast concrete interlocking paver blocks,any shape and size, confirming to IS-15658-2006 of 60mm thickness,M-35 grade, laid with grey cement and pigment complete all as specified and directed .

All as per Ser item No 23 here-in-before but except paver blocks complete all as specified and directed .

Dismantling of stone slabs and tiles of any description or thickness in floors,aprons etc,laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for taking down cement plaster on brick or stone walls/ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed .

M&L for preparation of newly plastered or unplastered surfaces of wall and applying two coat of cement base paint complete all as specified and directed

M&L for preparation of newly rough cast plastered surfaces of wall and applying two coat of cement base paint complete all as specified and directed

M&L for complete removal of existing treatment of old decorated surfaces of wall etc by brooming down and scrapping down smoke soot, moulds, moss and efflorescent salts , treating oil and greasy spots and applying one coat of cement base paint complete all as specified and directed.

Dismantling bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons etc (each layer) laid bedded and pointed in any mortar complete all as specified and directed .

M&L Pre-cast cement concrete 1:2:4, type B1 (using 20mm graded crushed stone aggregates ) as in kerb stone, set in cement mortar 1:4. including necessary form work , excavation for embedding blocks in ground to depth as directed and finishing exposed surface even and smooth complete all as specified and directed .

All as per Ser item No 32 here-in-before but except kerb stones complete all as specified and directed .

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed .

S&F Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying finishes complete all as specified and directed .

S&F Glazed ceramic coloured tiles 300mmx200mmx7mm thick (colour and shade as approved) as in vertical surfaces such as skirting/dados etc, set and jointed in neat cement slurry & pointed in white cement with pigment to match the colour of tiles over & including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed .

M&L for 20mm thick Granite (of approved type and colour) work (table rubbed and polished) fixed in any position in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with approved shade of granite including cutting over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6 type C2( using 40mm graded crushed stone aggregates) as in plinth protection/path finishing surfaces even and fair complete all as specified and directed .

Taking down shutter of any description exc 1 sqm but n.exc 2sqm each complete all as specified and directed

S&F Solid PVC door frame of size 50mmx47mm, made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed

S&F Factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail .MS frame shall be covered with heat moulded plain/coloured PVC "C"channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the style & rail with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed .

S&F aluminium alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminium alloy and fixed complete all as specified and directed .

S&F aluminium anodised barrel tower bolts,150 mm long of extruded section, fixed to doors with screws complete all as specified and directed .

S&F Aluminium anodised, fabricated type, handle 125 mm size complete all as specified and directed.

S&F 100mm mild steel butt hinges, medium weight,cold rolled complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads and fixed complete all as specified and directed

M&L for 3 mm thick, plain sheet glass, ordinary quality and glazing with oil putty or with wooden beads (supplied alongwith shutters) in squares n.exc 0.5 sqm each pane complete all as specified and directed .

S&F in repair Vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white, with integral foot rests, CI 'P' or 'S' traps 100mm & PVC flush pipes 32mm dia including connecting to trap and to flushing pipe, anti-syphonage pipe etc including all joints and making good to floor complete all as specified and directed.

S&F in repair 10 litres PVC,valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair flush pipe of polythene of low or high density or PVC, 32mm dia, for low level flushing cistern and fixed complete all as specified and directed .

S&F in repair PVC connection, 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed .

S&F in repair Stop valve, cast copper alloy,chromium plated, screwed down for high pressure with crutch or butter fly handle, screwed both ends for iron pipe of 15mm bore complete all as specified and directed .

Dismantling CI 75mm/100mm bore pipes including fittings jointed in cement mortar and taking out from below or above GL or laid in floos or fixed to walls complete all as specified & directed .

S&F 100mm dia cast iron soil, waste and vent pipe, in any length with or without ears with cement joints, laid in trenches/in floors or fixed to walls complete all as specified and directed.

Returning, filling in,including spreading, leveling, watering and well ramming in layers not exceeding 25cm complete all as specified and directed .

Removal of surplus soil to a distance not exceeding. 50 m & depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed .

Taking down carefully existing MCCB,MCB,DB TPN/SPN & making good the disturbed surfaces of walls, matching the colour with existing surface complete all as specified and directed. Note : Rate for making good shall be deemed to be included in above item rate.

Taking down carefully existing aluminium/copper point wiring for light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells & making good the disturbed surfaces of walls, matching the colour with existing surface complete all as specified and directed. Note : Rate for making good shall be deemed to be included in above item rate.

Taking down carefully existing submain wiring 2/4 run with earthing cable & making good the disturbed surfaces of walls, matching the colour with existing surface complete all as specified and directed. Note : Rate for making good shall be deemed to be included in above item rate.

Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLS with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed conduit of suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes, 2mm thick galvanised steel pressed sunken terminal boxes of suitable sizes for mounting of switches, sockets, fan regulator etc, covered with 2.8mm thick plastic laminate Hylem / Anchor top cover sheet of required colour, fixed with brass screws and cup washers, painting terminal boxes inside and outside with one coat of red oxide primer including continuous earth wire of size 1.5 Sqmm PVC stranded copper conductor unsheathed, insulated, stranded (Green colour) connected to common earth point dolly for for one light point/fan point/call bell point, 230 volts controlled by one switch complete all as specified and directed .

All as per Ser item No 61 here-in-before but for switch socket combination 5 Amp 5 Pin socket outlet 230 volts on same board with other switches complete all as specified and directed .

All as per Ser item No 61 here-in-before but for switch socket combination 5 Amp 5 Pin socket outlet 230 volts on independent board complete all as specified and directed .

All as per Srl item No. 61 here-in-before for Switch socket combination (multi purpose) 6 Pin 15 Amps 230 volts point to be controlled by one switch and wiring with 2.5Sqmm FRLS PVC unsheathed copper conductor and FRLS cable 2.5 Sqmm PVC insulated earth wire on independent board.complete all as specified and directed

S&F PVC Lamp holder with back plate suitable for batten fittings complete all as specified and directed .

S&F LED bulb 1 x 10 watt Lamp having luminous efficiency warranty 2 years complete all as specified and directed .

S&F complete set of tube light fitting, 1x20 watt LED (4 feet long), 230 volt, decorative ultra slim linear LED lighting fixture with environment friendly, energy efficient ready to use pack etc with all acessories such as LED adopter, LED tube, internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. Havells Cat Part No LUMILINEBS20WLED865SPCWH/Bajaj Cat Part no 830379 20WCDL/Crompton Cat Part No LDLL20-CDL

S&F complete set of tube light fitting, 1x10 watt LED (2 feet long), 230 volt, decorative ultra slim linear LED lighting fixture with environment friendly, energy efficient ready to use pack etc with all acessories such as LED adopter, LED tube, internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. Havells Cat Part No LHEXACP7IN1W010/Bajaj Cat Part no BCLSB 10W/Crompton Cat Part No LDLL10-CDL

S&F ceiling rose, three terminals, PVC polycarbonate, isolated body with bakalite 20mm back plate complete all as specified and directed .

S&F Sub main wiring with two runs of single core PVC FRLS sheathed, insulated, copper cable of 6Sqmm size, multi stranded, 1100 volts grade with PVC insulated FRLS copper wire 6Sqmm for continous earth wire drawn into and including PVC concealed conduit of suitable size complete all as specified and directed . Note :- Two runs of 6 Sqmm copper cable and one run of 6 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length)

S&F switch piano, flush type, single pole, one way, 5 /6 Amp,230 V,AC supply complete all as specified and directed .

S&F socket outlet, two in one, 5 Pin 5 Amps, 230 Volt, AC supply, complete all as specified and directed .

S&F switch piano, flush type, single pole, one way, 15/16 Amps, 230 volts AC supply complete all as specified and directed.

S&F socket outlet ,2 in 1, 5/6 pin, 15/16 Amps, 230 volts ,AC supply complete all as specified & directed.

S&F Sheet metal enclosure for DBs,TPN, double door, 415 Volts, 4 ways, vertical type and space for MCCB complete all as specified and directed .

S&F Sheet metal enclosure for DBs,SPN, double door, 230 Volts,8 ways with 200 amps rated bus bar complete all as specified and directed .

S&F MCB SP 5 to 32 Amp, 230 volts, B Curve with breaking capacity 10 KA complete all as specified and directed

S&F MCB, SPN, 32 amps, 230V, B Series with breaking capacity 10 KA complete all as specified and directed

S&F MCCB 3 Pole,adjustable type ,415 V, 100 Amps with breaking capacity 16 KA complete all as specified and directed.

M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment.

Supplying and laying, factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, laid flat and dry in trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, buried directly in ground vertically (depth of pit not less than 2.25m below normal ground level), with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to electrical equipment/GOD/LA and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI medium grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of precast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Schedule Part-I (2009), complete all as specified and directed. Note(s):- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with TMT bar 8mm dia both ways @100c/c. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m, excess beyond 7.5m length required at site shall be measured and paid separately. (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) Quoted lump sum / rate shall be inclusive of above all provisions.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 16 Sqmm, 4 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, including taking out existing one complete all as specified and as directed. Note: (i) Returning filling, earth work, sand cushioning and cable cover for protection of cable shall be measured and paid separately.

M&L for Steel water tubing of 25 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etc complete all as specified and directed .

S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed for 25 mm dia of pipe complete all as specified and directed.

S&F GI pipe, light grade, 40mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavement complete all as specified and directed. Note : (i) Excavation and earth work shall be measured and paid separately.

Supply, fixing and testing LED street / security light fitting of 25 Watt fitted on 4 to 9 meter high octagonal pole / wall/Swan neck pole including LED lamps complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminium alloy. The luminaries shall be monolithic construction, totally enclosed, dust and water proof with minimum IP-65 protection as per IS-10322-1982 (Part-I) with latest amendments and input voltage range 140-300V, AC, frequency 50-60 Hz, PF should be more than 0.9 with total harmonic distoration. THD (I) less than 15%, cool white colour and lamp starting time should not be more than 10 second, Fittings should be provided with 10 KV surge protection. Driver should be constant current constant voltage driver. Driver should have high voltage withstanding capacity upto 300V, AC. Driver should also have double phase protection, no load, open circuit and short circuit protection. LED light fittings should be suitable for ambient temperature from - 10 degree centrigrade to 50 degree centigrade and humidity level 10% to 90% RH. Covers should be polycarbonate/ toughened glass to ensure minimum IP 65 degree protection. Cover should not degrade due to heating and ageing. The efficient of LED luminaries system shall be more than 85 lumens per watt and must be certified by LM-79 test report fixed on and including bracket of 40mm dia,light grade ,GI pipe ,1.20 m and connecting with twin core twisted flexible copper conductor cable 1.5 Sqmm complete all as specified and directed. Note :- (a) Bidder shall submit test report of LED street light fitting from accredited test laboratory for LM-79 (b)Bidder has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of CA. The product will be replaced free of cost in the following cases : - (i) Manufacturing defects (ii) Failure due to mechanical and electrical impact, (iii) Drop in lumen (or lux at 1m) below 90% of claimed values of lumen (or lux at 1m) of the LED/ luminairies. (c) All LED light luminaire must meet the provision laid down in IS-16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part-II/ Section 13 (d) Scope of work shall include supply and fixing street light fittings on poles which includes required T & P and accessories etc if any, making connection, testing etc complete. No extra payment is admissible on these account.

S&F 1X10 watt LED retrofit type bulk head fitting luminaries, die cast, aluminium alloy body, heat resistant, prismatic glass cover with specially designed gasket, lamp holder etc complete with all accessories and including connecting up with twin core twisted flexible copper coductor cable with suitable size of 230 volt,50 HZ complete all as specified and directed.

Supply & fixing Energy efficient Ceiling fan complete with blades, down rods, electronic type regulator & accessories, 230 V,1400mm sweep, minimum air delivery 210 CFM with service value 6.00 BEE, 5 star rated with brushless direct current motor (BLDC) including writing of MES number (Black, Roman, Italic or Indian) n. exc 30cm height complete all as specified and directed

Supply and fix electric water heater, storage type, steel body with copper inner tank and heating element upto 2 KW capacity, 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc with nut bolts, inlet and outlet connection with PVC tube for cold water inlet and PVC reinforced tube for hot water outlet complete all as specified and directed

S & F exhaust fan ,steel body, AC single phase, 4 blades with louver shutter suitable for operation on 220/230 volts of 300mm sweep and all fixing arrangements like wall hole, material etc complete all as specified & directed Note :- A Sum of Rs. 25,712.00 will be deducted on account of credit for dismantling/ demolished/ taking down material. Please refer detail on srl page No. 28 (Schedule of credit) of Tender Documents.

SHIV SHAKTI BUILDERS

NEW AMRITSAR CONSTRUCTION COMPANY

BANSAL BUILDERS

N.G BUILDERS