PROVISION OF ROAD FROM AKSHAY VIHAR TO SANGAM GATE AT OD FORT CANTT UNDER GE (EAST) PRAYAGRAJ.

Amount

Surface excavation in soft/loose soil n.exc (not exceeding) 30 cm deep and averaging 15cm over area and getting out including cutting to required gradient and camber as for formation of roads or berms complete all as specified and directed.

Surface dressing n exc 15 cm deep complete all as specified and directed.

Rough excavation not exceeding 1.5 m deep and getting out as in hard/dense soil n exc 1.5 m deep and getting out complete all as specified and directed.

Excavating over areas, as in soft/loose soil n exc 1.5 m deep and getting out complete all as specified and directed.

M&L for Rolling and consolidating formation surfaces of road with 8 to 12 tonne power roller including filling depression which occur during the process of rolling of formation to required level,gradient,camber and super elevation including necessary watering & filling complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, laying of cable and foundation of poles stays etc. and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each complete all as specified and directed.

Removing excavated soil material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for Rolling and consolidating formation surfaces of road with 8 to 12 tonne power roller including filling depression which occur during the process of rolling of formation to required level,gradient,camber and super elevation including necessary watering & filling complete all as specified and directed.

M&L for Brick work with subclass ‘B’ bricks, old size burnt clay bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4 complete all as specified and directed.

M&L for PCC type D2, 1:4:8 using 40mm graded stone aggregate for foundation filling as mass concrete etc complete all as specified and as directed

M&L for providing plain cement concrete type B1, 1:2:4 using (20mm graded stone aggregate ) as in coping, string course etc complete all as specified and as directed

M&L for rendering 15 mm thick in cement mortar 1:4 on brick work or concrete surfaces for finishing the surface fair and even. without using extra cement complete all as specified and directed.

M&L for Preparing of new plastered or unplastered surfaces of walls and applying two coats of cement base paint in approved colour/shade over a coat of primer complete all as specified and directed.

M&L Continuous brick edging with With burnt clay bricks of sub class 'B ' old size brick width equal to the width of the brick; laid dry on end vertically complete all as specified and directed.

M&L for 150 mm thick soiling(spread thickness) with broken boulders or quarried stone,interstices filled,surface formed,rolled and consolidated to required gradient and camber with 8 to 10 tonne power roller complete all as specified.

M&L for 150 mm thick thick (compacted thickness) WBM, with coarse aggregates of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated with 8 to 12 tonne power roller to required gradient ,camber and super elevation required complete all as specified. Note:- Each layer shall be laid and rolled separately.

M&L for Bituminous Macadam with 100-120 TPH hot mix plant producing an average output of 75 ton per hour using crushed stone aggregate of specified grading premixed with bitminous binder binder VG-30 grade @ 4% by weight of total mix transporting the hot mix and filler to work site, spreading and laying with a hydrostatic mechanical paver and roller to required camber/ gradient rolled and compacted to smooth uniform surface with vibratory and tandem 8 to 12 ton power roller to achieve desired compaction (consolidated thickness 75 mm thick or less) complete all as specified and directed.

M&L Preparing black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc and applying evenly a priming/tack coat with bituminous VG30 @ 05 kg per 10 sq metre and laying bitumen premixed asphaltic semi dense concrete 40mm thick ( consolidated thicknes)premixed bituminous asphaltic dense concrete with crushed and graded aggre9ate mixed together with using paving bitumen Of VG30 (minimum 5.5% by weight of total mix ) to rneet desired requiremerts,mixing bituminous concrete in hot mix plant ,laying and spreading uniformly by means of mechanical paver and compacting to required camber and graüient using by power road roller h 8 to 12 tonne power roller to a uniform surface as required including cutting of edges of roads straight and site clearance complete all as specified and directed.

M&L for Moorum red Bajri (spread thickness 100mm) spread, rolled and consolidated to gradient and camber required using 8 to 12 ton power roller including surface dresssing/cleaning and removing grass, vegetation/scum complete all as specified and directed.

M&L for Reinforced concrete pipes of dia 300mm, class NP2, laid and jointed complete with collars complete all as specified and directed.

M&L for Concrete bed 1:3:6 type C-2 to drain pipes of bore 300 mm including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

S & F Cat eyes, solar reflective type of material body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972 fixed with ms stud of suitable size as per manufacturers instructions complete all as specified and directed.

S&F Cat eyes, 100mm x 100mm x 18.5mm size dynamically designed very high impact strength and fitted with 2 Nos highly reflective reflectors complete all as specified and directed.

Supply and fixing metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150mm x 150mm x 300mm) type B1 complete all as specified and directed

M&L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed

S&F modular rubber speed breaker/rumble strip having dimension 500mm x 400mm x 75mm compact high resistance to moiture, capacity to withstand severe impact and colour yellow black model No.GSB-75, acrelic reflective fixed on front and bace help in identifying the location of the speed breaker from a large distance fixed suitable size as per manufacturer instruction complete all as specified and directed.

Providing and fixing convex mirror of size 1000 mm made of PC materials provided with suitable MS pipe, duly powder coated as per site requirement complete all as specified and directed.

Dismantling posts or struts of wood/steel/RCC embedded in concrete/brickwork/ masonry/ground, any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

Dismantling of fencing wire mesh, any type, size, of any description and in any position complete all as specified and directed.

Excavating in post holes (or similar' holes), in soft/loose soil, each not exceeding 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and directed.

M&L for PCC (1:2:4), type B1 using (20mm graded stone aggregate) as in foundation, filling and mass concrete of fixed post complete all as specified and directed.

M&L for RCC (M-20) using (20mm graded stone aggregate) as foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC (M-20) using (20mm graded stone aggregate) as Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for Formwork as rough finished surfaces to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed .

M&L for Formwork as rough finished surfaces to sides of concrete to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed .

M&L for preparation of wall surfaces and apply two coat of cement base paint over a coat of Chalk whiting complete all as specified and directed.

M&L 15 mm thick rendering in cement mortar 1:4 on brick work or concrete surfaces for finishing the surface fair and even. without using extra cement complete all as specified and directed.

M&L for preparation of wall surfaces and apply two coat of cement base paint over a coat of Chalk whiting complete all as specified and directed.

S&F rolled mild steel of angle iron fencing posts and struts Fe-410 (Grade E-250) qualityB angle or tee section as in post, cut to length and bend to shape as directed, fixed independetly without connecting plate etc, including provision of 05 to 06 Nos gaps/cuts/holes in each post for providing/laying barbed wire& chail link fencing complete all as specified and as directed. (Note :- Supply and fix barbed wire shall be measured and paid separately)

S&F of Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing completFe-410W(GdeE-250) quality complete all as specified and directed.

Supply only mild steel galvanised chain link fencing of 4mm dia and mesh of any size & any type for fixing to standards, rails, straining bolts, etc. complete all as specified and as directed.

Fixing only chain link fencing of new/old as 4mm dia and mesh of any size including line wires, fixing to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips and complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not exceeding 10cm in width or girth and applying two coats of approved colour synthetic enamel paint, over a coat of red oxide zinc crome primer complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not exceeding 10cm in width or girth and applying two coats of approved colour synthetic enamel paint, over a coat of red oxide zinc crome primer complete all as specified and directed.

Supply and laying, joing and testing of XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 06 sqmm 4 core laid in trenches, ducts, pipes complete all as specified and directed.

Supply, laying, testing GI water tubing light grade, 40 mm bore for mechnical protection of cable complete all as specified and directed.

M&L for sand cushioning to underground cable, provided with a layer 8 cm before and 15 cm after laying and stretching jointing and testing the cable complete all as specified and directed. Note: Punned thickness of sand shall be measured.

Supply and laying brick covering with width equal to length of brick as mechanical protection to cable using sub class ‘B’ bricks laid flat, size 230mm x 115mm x 75mm, complete all as specified and directed.

Supply and fixing weather proof flat twin core wire with PVC pipe with stranded aluminum conductor of size 4 sqmm complete all as specified and directed.

S&F of steel tubular pole 410-SP 31 (9.0m long pole) complete with cast iron base plate, pole cap, mild steel bolt, nuts and screws complete all as specified including consisting of following works:- (a) Excavation in trenches not exceeding 1.5 mtr wide & 1.57 mtr deep for pole foundation & getting out in soft/loose soil, returning filling in the excavated of soil after fixing the pole in foundation ramming earth around in layer not exceeding 25 cm thick and disposal of surplus soil to a distance not exceeding 50 mtrs complete all as specified and directed. (b) M&L for PCC 1:4:8, type D2 (using 40mm graded crushed stone aggregate) in foundation 900mmx600mm cross section and planting depth 1.5 mtr for concrete encasing the pole upto GL complete all as specified and directed. (c) M&L for providing PCC 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) for plinth block/collar above GL 500mm high and 450mm dia complete all as specified and directed. (d) M&L for painting of pole externally with one coat of black bituminous paint (upto planting depth) and above plinth block concrete collar with two coat of aluminium paint over a coat of red oxide primer including preparation of surface including painting of 30 cm wide bands 3 Nos with synthetic enamel paint of appropriate colour in alternate layer upto the height of 1.5mm above plinth block. (e) M&L for writing letter or figures (Block Roman, Italic as Indian) with thick synthetic enamel paint of apprised shade not exceeding 5 cm height including numbering of pole complete all as specified and directed. NOTE : Manufacture's test certificate of pole will be produced before execution work.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete complete with connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 1.0 sqmm complete all as specified & as directed by Engr in Charge.

S&F street light bracket made out of 32 mm dia GI medium grade pipe 1.2 mtr long bend to shape 120 degree and fixing with 2 Nos of MS clamps of 50mm x 6mm thick flat iron including nuts, washers bolts complete fittings arrangement suitable for any type of poles.

M&L for junction box of size 30X25X15cm ( internal dimension) made out of 2mm thick MS sheet weather proof including one coat of red oxide primer and two coat of synthatic enameled paint and fixing arrangement etc using suitable clamps nuts, bolts etc for accommodating and including the following:- (a) Two strip aluminium bus bar of capacity 40 A, including and mounted on epoxy insulators-01 Se.t (b) MCB SP 6 Amps-01 No.

Replacement of wall mounted Distribution Board factory made of size 600mm x 450mm x 150mm made of MS sheet 2.0 mm thick CRCA sheet with powder coated paint ,dust and vermin proof with front openable door and locking arrangement consisting of following accessories: (a) MCCB 63A, 4 pole 25kA fixed magnetic and thermal release - 01 No (incoming) (b) 3 phase and neutral bus bar copper LT 440V, 200 A (outgoing) (c) Phase indication lamp LED type R,Y,B

S&F digital type 24 hrs astronimical type timer switches suitable for operation of street light luminarie with 4 pole Power contactor of 63 A capacity - 01 No suitable for 3 Phase, 4 wire system incl necessary MCB TPN 63 A capacity - 01 No as control the system, fixed in the Outdoor type LT junction box madeup of powder coated CRCA sheet steel enclosure 3 mm thick floor mounted of suitable size all as specified and as directed.

M&L for Earthing complete with steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel earthwire protected by provision of GI medium grade pipe 15mm bore including provision of concrete pit made from PCC (1:2:4) type B-1(using 20mm graded stone aggregates) with 17mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 Kg/Sqm) and frame of angle iron 25 x 25 x 6mm with lugs 02 No and with 6mm dia MS bar handle made to shape, GI medium grade 20mm bore pipe for watering perforated at bottom, 1.75 metre long placed on top edge of earth plate, common salt & charcoal filling, test point made out of 17mm x 8mm FI with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No.5 of SSR Part-I connected to earth test point all as specified or indicated including testing on completion all as specified and as directed.

M/s NSA Engineering Corporation (BID ID -3148745)

SAKSHAM BUILDERS AND ENGINEERS (BID ID -3143524)