Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹49.4 LAccepted-AOC | L1 | Accepted-AOC First lowest | |
| 2 | L2₹50.2 L+₹18,822.10 (0.38%)Rejected-Finance | L2 | Rejected-Finance Higher bid value | |
| 3 | L3₹50.6 L+₹58,451.85 (1.17%)Rejected-Finance HOUSE NO 59 THILIXU VILLAGE BLOCK V PS POST DIMAPUR NAGALAND 797 112 | DIMAPUR | DIMAPUR | NAGALAND | 797112 | L3 | Rejected-Finance Higher bid value | |
| 4 | L4₹51.3 L+₹1.2 L (2.49%)Rejected-Finance OLD DAILY MARKET DIMAPUR 797 112 NAGALAND | PEREN | NAGALAND | 797112 | L4 | Rejected-Finance Higher bid value | |
| 5 | L5₹52.4 L+₹2.4 L (4.72%)Rejected-Finance H NO 400 FLAT NO 13 A SEMATILLA DIMAPUR 797112 NAGALAND | DIMAPUR | DIMAPUR | NAGALAND | 797112 | L5 | Rejected-Finance Higher bid value |
Tender Value
₹48.5 L
EMD Value
₹97,000
Closing Date
10 Dec 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE 868 EWS
GE 868 EWS PIN- 913 868 C/o 99 APO
SPL REPAIR TO BLDG NO T17 AND OPT431 OF 3 CIB ADDN ALTN TO BLDG NO T4 TRIVENI COMPLEX BLDG NO T5 IN C ZONE PROVN OF FLOOR TILING OF BLDG NO T6 AND T8 AT SPEAR COMPLEX AND PARKING SHED WITH HARD STANDING NEAR BLDG NO OPT240 BCC HALL AT CORPS HQ AT RMS
2022_MES_551526_4
8492/C/E8
Open Tender
Civil Works
Item Rate
180 days
RANGAPAHAR
Class D, Category a(i)
3 documents required · 3 mandatory
₹500
GE 868 EWS
₹97,000
1 Feb 2023
21 Nov 2022
12 Dec 2022
21 Nov 2022
10 Dec 2022
28 Nov 2022
21 Nov 2022 - 26 Nov 2022
Amount
B/R Portion Demolition of brick work built in cement mortar incl all quions, arches pillars etc but excl ashalar facing complete all as specified and directed.
Demolition of reed, lathing single or double, including battens and plaster or chicken wire lathing complete all as specified and directed.
Dismantling timber scantlings unframed work 40 sqcm and over in section in any position complete all as specified and directed.
Demolition of plain cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.
Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.
Dismantling wall and ceiling board fibre, pulp insulation etc or insulation boards any thickness including cover fillets complete all as specified .
Dismantling, floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed.
Taking down Chowkhat or frames not exceeding 1.5 Sqm each with shutters(Without taking off shutters from the frames complete all as specified and directed.
All as per item 8 above but exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.
Taking down shutters of any description not exceeding 1 Sqm each complete all as specified and directed.
Taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed.
M&L for surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.
Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for fdn, n.exc 10 sq m on plan and n.exc 1.5m in depth and getting out in soft/loose soil.
Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil complete all as specified and directed.
M & L PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation etc and mass concrete complete all as specified and directed.
M&L for PCC 1:4:8 type D-2 (using 40mm graded stone)as in fdn filling mass concrete complete all as specified and directed.
M&L Brick work with sub class B brick straight or curved on plan exc 6.00 m mean radious built in CM 1:6 complete all as specified and directed.
M&L brick work with sub class "B" bricks straight or curved in plan exceeding 6 mtr mean radius built in CM(1:4) using old size bricks complete all as specified and as directed.
M&L brick work with sub class B bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4
M&L roughening surface of old concrete floor/Dado, skirting by picking ,sweeping clean and washing down with water to remove dust etc.
M & L 40mm thick PCC 1:2:4 B0 (12.5mm graded crushed stone aggregate ) as in Damp proof course to horizontal or vertical surfaces including necessary form work complete all as specified and directed.
M&L for hardcore of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammmed to a true surface complete all as specified and directed.
M & L for 100 mm thick PCC 1:4:8 type D-2, (using 40 mm graded stone aggregate) as in sub base over polythene sheet complete all as specified and directed.
M&L for PCC 1:3:6 type B2 (40mm graded stone agg) 100mm thick as in base/ sub base complete all as specified and directed.
M & L 25mm thick PCC 1:2:4 , B1 (20mm graded crushed stone aggregate ) as in floor for level coarse complete all as specified and directed.
M&L for 15 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor complete all as specified and directed.
M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and directed.
M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick CM (1:4) backing coat complete all as specified and directed.
S&F Non skid ceramic floor Colour tiles of 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.36 sqm in floors etc with 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:6), set and jointed in neat cement slurry and pointed in coloured cement complete all as specified and directed.
Same as per ser No 29 but on vertical surfaces such as skirting , dado risers to steps over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed.
S&F Non skid ceramic floor Colour tiles of 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc with 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:6), set and jointed in neat cement slurry and pointed in coloured cement complete all as specified and directed.
M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid, jointed with grey cement and no pigment complete all as specified including preperation of formation bed over 25 mm thick sand cusion and pointed in colour cement mortar 1:3 complete all as specified and directed.
S&F steel work in tubular trusses, post, purlins including special shaped washer etc. Complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 complete all as specified and directed.
S & F for bands, straps, supports or stays for rainwater, ventilating pipes, incl bolts, if reqd : hooks (say), heavy, for large gates, hook and pintle hinges : large hasps and staples; chains; hand made sliding bolts ; clamps; hold fasts; waal ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts,; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde E-165 complete all as specified and directed.
S&F mild steel framed work such as post, grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.
S/F 2nd class hard wood scantling as in purlins rafters & framed work etc clean sawn complete all as specified and directed.
Taking down cement plaster and raking out joints, hacking for key,scrubbing down with water built in cement mortar.
M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished fair and even without using extra cement.
M&L for 15 mm thick rendering on fair faces of brick/concrete surfaces in CM (1:4) and finished even and smooth without using extra cement all as specified & directed.
M & L rendering 10 mm thick in cement mortar 1:6 on fair faces of brick or concrete work even and smooth without using extra cement.
S&F for pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as complete all as specified and directed.
M & L for RCC M-20 (Nominal Mix) Type A1, 1:1 1/2:3 (20 mm agg) in lintel, beams, cantilivers complete all as specified.
M & L formwork to sides and soffits of floor or roof beams,beam haunchings, girders, bressumers, lintels, cantilever, shelves including supports, overhangs, etc also splys between floors and beams etc compete all as specified directed.
M&L for TMT steel bars 10 mm dia and over, cut tro length, bent to shape required, including cranking, bending spirally or hooping for coloum hooking end stand binding with miuld steel wire less than 0.9 mm dia complete all as specified and dierected.
All as per item No 44 here-in-before but 5 mm dia and over upto and including 10 mm dia TMT bars as in stirrups, spacers and binders, conferming to geraded IS -432 (Part-I) complete all as specified and directed.
Mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape reqired including cranking, bending spirally for hooping ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to TMT bars
Returning, filling in trenches including shearing , leveling, watering in layers n.exc 25cm thick soft loose soil complete all as specified and directed.
Removal of excavated soil n.exc 50mtr distance and depositing where directed n.exc 1.5m above the starting point complete all as specified and directed.
M&L PCC 1:3:6 Type C-2 (using 40mm graded stone aggregate) as in plinth protection, foot path, paved area, etc finished even and fair without using extra cement 75mm thick complete all as specified and directed.
M & L for PCC (1:3:6) type C-1 using 20mm graded aggregate as in coping including necessary form work all as specified and directed
Material & labour 2nd class hardwood plain, solid straight chowkhats and frames, wrought, framed rebated on the solid,rounded or chamfered, put together with glue pinned at joints, 2nd class HW.
M&L for 35 mm thick 2nd class hardwood plain framed pannelled shutter (any number of panels) with panels of timber flat on both sides or of veneered particle board medium density , wood particle board with commercial face veneers , supplied and fitted to chowkats complete all as specified and directed.
Refixing of Shutter of any description exc 1 sqm and n exc 2 sqm each in same opening complete all as specified and directed.
S &F 35mm thick 2nd class hardwood glazed and skeleton shutters open rebated and prepared to receive glass gauze etc divided into squares, with plain, chamfered or rounded mitred and rebated sash bars any number edges of framing plain, chamfered or rounded, fitted with cut and metered beads for securing glass etc size of members of shutters as specified in SSR Part I Sec 8 clause 8.23 (a) complete all as specified and directed.
S&F 30 mm thick 2nd hardwood glazed and skeleton window and ventilator shutters, 30mm thick, open rebated and prepared to receive glass, gauze, etc. ( with and without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (b); supplied and fitted to chowkats. all as specified.
Refixing of Shutter of any description n exc 1 sqm each in same opening complete all as specified and directed.
S&F factory made 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels, both face is covered with decorative choice sunmica lamination 0.9mm thick type I with lipping to match fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.
M&L for sheet glass 3mm thick ordinary quality, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane.
S&F mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 18mm, fixed with tinned tacks or galvanized wire staples.
S&F Solid PVC Door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube,supplying and fixing in opening as per specification and drawing.
M&L for factory made solid panel PVC door shutter, 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frames shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles plain colour PVC sheets for top rail, lock rail and bootom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame, welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site with three nos of MS higes medium grade complete all as specified and directed.
S&F 150 mm long aluminium anodised tower bolts.
S&F 100mm long aluminium anodised handles cast copper.
S & F 100 size stainless steel butt hinges complete all as specified and directed
S & F 75 size stainless steel butt hinges complete all as specified and directed
Supply & Fixing 150 mm Aluminium handles, cast type, anodised
S & F 200 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed
S & F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed
S&F mild steel 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete
S & F floor door stopper of aluminium alloy body and tongue, anodised wit hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified and directed
M&L for rendering 15 mm thick in CM 1:4 on one side of lathing finished even and smooth without using extra cement.
M&L for rendering 12 mm thick in CM 1:6 on other side of lathing finished even and smooth without using extra cement.
S & F 0.71 mm dia wire netting of galvanised steel wire of size 12 mm mesh fixed with tinned tack of wire staple.
S&F for steel ventilator with top hung shutter including hinges steel peg stay, complete all as specified and directed.
M/L sheet glass, obscured or frosted 3mm thick and glazing with oil putty in squares. nexc 0.5 Sqm each
Material and labour RCC (Nominal Mix) in cement concrete 1:1 1/2:3 type A1 using 20mm graded stone aggregate as in slab supported on walls ,beams and columns in floors, roofs, landings, cover slabs of drains, manholes, septic tanks, soakage wells etc. complete all as specified & as directed by Engineer-in-charge. Note: - Reinforcement shall be measured and paid for separately.
Formwork to soffits of suspended slab such as roof slab, floors slabs landings and similar work not exc 200 mm thick
Formwork to edges of concrete flats, treads breaks in floors, window cills, concrete railings openings in concrete walls, floors and roofs not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but not exc 20 cm
S&F rotational moulded polyethylene 1000 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia all as specified and directed.
S&F 20mm gun metal, globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed.
M/L for PCC (1:2:4) type B1 using 20mm aggregate in plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed.
RCC (1:2:4) type B-1 in manhole/soack well/septic tanks slabs/covers etc including necessary form work complete set in cement mortar 1:4 complete. Note: - Reinforcement shall be measured and paid for separately.
Cutting into existing manhole/soakwell/septic tank making good to pipe and benching cutting out existing benching for and forming branch channel (half round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required for internal dia size 150mm.
M & L rendering 15mm thick in cement mortar 1:3 mixed with water proofing compound @ 3% by wt of cement finished fair faces of brick/concrete surfaces even and fair without using extra cement .WPC will be measured and paid separately.
Supply only integral water proofing compound ( ISI marked )
M & L cement concerte in surface channels and drains type C-2 1:3:6 using 20mm graded aggregate
Extra for forming fair finished surfaces of drain or channels, inner girth 30 cms, using extra cement including forms, moulds mitred/ stopped ends etc.
Taking up or down steel tubing 15mm bore and connection including cleaning for refixing or removal to store.
All as per item No 88 hereinbefore but 20mm dia .
Refixing 15mm dia old GI tubing and connection in new or old position (wall ceiling floor etc including cutting altering the size or changing the new fittings etc complete all as specified .
All as per item No 90 hereinbefore but 20mm dia.
S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 15 mm bore.
S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 20 mm bore.
S&F in repairs vitreous china water closet Padestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe and including EWC Sheet cover complete all as directed.
S&F in repairs10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and handle complete all as specified .
S&F 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and dual flush type complete all as specified (Make Cera, F1020106) complete all as specified and directed.
S&F vitreous china water closet Padestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe and including EWC Seat cover complete all as directed.
Supply only flush pipe of polyethylene of low or high density of PVC 32mm dia for low level cistern.
S&F CP Health Faucet with 1 mtr metalic Expandable tube & hook complete all as specified and directed and as approved by GE
S& F cast iron P or S trap of 100mm dia
S&F 15mm dia stop cock fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed .
S&F CP wall mixer (3 in 1) complete all as specified and direcated and as approved by GE.
S&F for 15mm dia of pipe bib taps cast copper alloy, fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed.
S&F brass CP mixer for basin mixing hot & cold water screwed down for iron pipe and fixed 15mm dia pipe complete all as specified and direcated and as approved by GE.
S/F Fancy type brass chromium plated shower rose 125 mm in size with or without swivel joints any size incl fixing to steel pipe or union, complete all as spd & directed
S&F soap dish chromium plated stell/stainless steel, approx size 160x160mm x 1mm thick , fixed to walls with plugs & CP brass screws complete all as specified and directed.
S&F 600mm long tubular tower rail brass chromium plated 20mm dia, D type 60cm longfixedwith two plugs (Gutties) of 2nd class hard woodembeded in cement mortor 1:3 with MS screws complete all as specified.
S&F Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.
S&F corner glass shelf assembly 250mm radius made of 6mm thick craaylic glass, with CP railing, fixed with suitable rowal plug & screws complete all as specified and directed.
S&F vitreous china wash basin, size 550 x 400mm white including brackets, and waste coupling & pipe of 32mm dia, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed.
M&L for DWCPE (SN8) 150 mm (ID) diameter Pipes laid in trenches complete all as specified and directed.
M&L for Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:3:6 type C2.
S&F PVC (SWR) 110mm dia single socketed in any length with rubber ring joints laid in trenches or in floor all as per specified.
S&F PVC (SWR) 110mm dia single socketed in any length with rubber ring joints fixed to walls.
S&F PVC (SWR) 110mm dia bends in any radius.
S&F of PVC (SWR) 75 mm dia pipe as per specification.
S & F 75mm bore PVC (SWR) bends any radius complete all as specified and directed.
S&F PVC (SWR) 110mm dia junction single T equal or un equalwith an floor
S&F PVC (SWR) 75mm dia vent cowl
S & F in repairs for 75mm bore dia pipe stack clamps out of 50 mm by 5mm flat iron & 16 mm dia round iron stays, including bolts & nuts & secuirng ends of stay to wall or roof
S&F for PVC Connection pipe 15mm size with PTMT nuts of length 450 mm complete all as specified and directed.
M & L for bib cock CP with wall flange, fancy type 15 mm dia bore.
M & L for angular stop cock CP with wall flange, fancy type 15 mm bore dia.
S&F CP grating 100mm dia PTMT with waste hole (Min wt 25 Gms).
S & F in repairs for Draperly rod/Harrison rails of CP of 20 mm dia with fixing brackets, Stops rollers and rings etc
M & L for cement concrete type C-2, 1:3:6 (40mm graded stone aggregates) as in surface channels and drains
M & L for Extra forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement
S & F second class hardwood weather boarding, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps.
M&L for preparation of old surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint in any tint complete all as specified.
M&L for Preparation of old decorated surfaces and appplying one coat of white wash on walls, cornices etc. complete all as specified and directed.
M & L for preparation of new surfaces of wall including scrapping down, smoke soot, efflorescent salts trading oil and greasy spots etc by applying two coat of white wash on walls
M & L for preparation of newly surfaces of walls and applying two coats of oil bound distemper (oil emulsion) over one coat of chalk whiting all as specified and as directed.
M&L for applying two coats of oil bound distemper over one coat of primer over a coat of 3mm thick wall care putty on new plastered surfaces of walls including preparation of new surface complete all as specified and directed.
M &L for preparation of old decorated surfaces of walls by washing, rubbing down and stopping of distempered surfaces and applying one coat of oil bound distemper of approved shade/tint all as specified
Material and labour for preparation of new external surfaces of walls including cornices, plasters etc (Plastered or un plastered surfaces) and applying two coats of cement paint over one coat of primer complete all as per manufacture instructions all as specified and as diredted by Engineer-in-Charge .
Material and labour for preparation of old external surfaces of walls including cornices, plasters etc (Plastered or un plastered surfaces) and applying one coats of cement paint including complete removal of existing surfaces all as per manufacture instructions all as specified and as diredted by Engineer-in-Charge .
M&L for preparation of new surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of redoxide on new surfaces in any tint complete all as specified.
M&L for preparation of new wall surfaces plastered or unplastered and applying three coat white wash on undecorated surfaces complete all as specified and directed.
M&L for preparation of preparation of new plastered or un- plastered surfaces and walls including cornices, pilasters etc and applying two coats of cement base paint over a coat of primer complete all as specified and as directed.
M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.
S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-painted self embossed, textured designer board E-Board Classic to be fixed or laid with GI frame grid/section size 600mm x 600mm with main runner 38x24x0.9 mm thick, cross tee 8.6x24x0.9mm and wall angle 19 x19x0.9mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size complete all as specified.
S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed.
M&L for Solid PVC Wall Lining consisting of 5mm thick Plain or coloured with wood grains printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame all as specified and directed.
M&L second class hardwood plain fillets exc 13sqcm and not exc. 25sqcm, square or rectangular in section, wrought, secured with nails or brads.
M&L for preparation of new wooden fillets surfaces and wood based surfaces of any description not exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pint wood primer. in tint as directed.
M&L for preparation of old painted wood and wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint in any tint all as specified and directed
M&L for preparing surface of wood and wood based matreials, new or old, of any description and girth and treated with tar or coal tar black paint and sanding newly tarred surfaces with clean sharp sand.
S&F anodised aluminium colour frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified
S & F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.
S & F for aluminium Window and ventilator shutters, without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified.
M&L for fixing 4 mm thick anodised aluminium composite panel fixed in aluminium frame including necessary rubber beading, jointing cleats complete all necessary items to fix with frame and all as specified and directed by Engineer-in Charge.
S&F Sheet glass 5.5mm thick, Clear/ Sun shade colour glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5sqm in each pane.
S&F Sheet glass 4mm thick clear/sun shade colour glass, ordinary quality and glazing with oil putty in squares exceeding 0.5sqm in each pane.
S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and fixed with tinned tacks or galvanised wire staples all as directed by Engineer- in -Charge.
S&F aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.
S&F in Mortice lock,vertical type Aluminium 2 levers, size 100 mm
M&L butt hinges medium grade cold rolled mild steel and fixed size of hinges 100 mm long size
S/F Aluminium anodised barrel tower bolt of extruded section and fixed 200 mm long
S&F 40 mm flap width of Continuous (piano) hinges, mild steel, bright finish or electrogalvanised.
M&L for 19mm thick Block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on one face fixed with screws to timber framework
M & L for 20 mm thick 2nd class hardwood Boarding clean sawan with butt jointed, fixed in shelves; Par titions and shelves of built-in cupboards, almirahs, book cases, toilet boxes, racks, pelmets and similar work fixed with nails in any situation (except flooring and skirting)
S&F 40 mm cupboards knobs fixed with nut screw and washer of brass polished complete as specified and directed.
S&F magnet Catcher for cub board complete all as specified and directed.
E/M Portion Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and as directed.
M&L for Point wiring complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site complete all as specified and as directed.Make:- Richa/KEI/Polycab/Havells /RR Kabel Make of caping/casing :- Prestoplast/Finolex/supreme/Richa
All as per item No. 167 but for One light/ Bell Point controlled by one way switch .
All as per item No. 167 but for One Exh/Ceiling fan point controlled by one, one way switch.
All as per item No. 167 but forOne 3 pin socket outlet 5 Amps on the same board with other switches.
All as per item No. 167 but forOne 3 pin socket outlet 5 Amps on the Independent board.
All as per item No-167 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed. Make:- Richa/KEI/Polycab/Havells /RR Kabel Make of caping/casing :- Prestoplast/Finolex/supreme/Richa
M&L for Switch piano flush type single pole, one way 5A Make:- Havells/Legrand/Anchor
M&L for Socket outlet, 2 in 1, 3 pin 5A flush type Make:- Havells/Legrand/Anchor
M&L for Switch Socket combination, 2 in 1, 5 pin 5A flush type Make:- Havells/Legrand/Anchor
M&L Switch socket combination 2 in 1, 5A/16A, 5 in 1 flush type Make:- Havells/Legrand/Anchor
M&L for stepped type electronic fan regulator 100/120 Watt socket size flush type on the existing phenolic laminated sheet etc. Make:- Havells/Legrand/Achor
M&L for bell push switch 5 amp flush type. Make:- Havells/Legrand/Anchor
M&L for Bell, AC, 230 Volts, single pole Make:- Havells/Legrand/Anchor
M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body complete all as specified and directed. Make:- Havells/Legrand/Achor
M&L for sub main wiring with two runs of 4 Sq mm and one run of 4 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn through and including PVC double locked Casing & caping including complete all as specified and as directed. NOTE:- two runs of 4 Sq mm + one run of 4 Sq mm and one run of PVC casing & capping and its accessories of suitable size shall be measured as one unit length. Make:- Richa/Finolex/RR Kabel Make of caping/casing :- Prestoplast/Finolex/supreme
S&F for , IP>= 20, Class-I, LED Light fitting 1 x 20 watt (4 Ft), 240 V, PF-0.9, CRI >= 80, CT>= 6000 K, Wall/ Surface mounted, intergrated type with all accessories internally prewired and incl connecting up with and incl twin/ three core twisted flexible copper conductor cable of suitable size in and incl flexible hose from ceiling rose to fitting complete all as specified and as directed. Make : Crompton Geaves/ Bajaj/ Philips/Havells.
All as per item No 178 here-in-before but 9 watt LED, 2' batten, Wall mounted with polycarbonate housing/ batten. Make : Crompton Geaves/ Bajaj/ Philips/Havells.
All as per item No 178 here-in-before but 10 watt LED, 2' batten. Make : Crompton/Bajaj/Havells/Philips
M&L in replacement for Decorative wall mounted light fitting made up of polycarbonate including 9 watt LED lamp with B-22 base including taking down old unsv light fitting complete all as specified and as directed. Make : Crompton Geaves/ Bajaj/ Philips/Havells.
Supply and fixing LED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. Make : Havells/Bajaj/crompton/Philips
Supply , fixing and testing in replacement of LED bldg Street light fitting of capacity 20 watts, CRI > 70, Power factor > 1.95, colour temp 5700 K, Luminous effieciency not less than 100 lumen/watt, 6000 Lumens output, IP-66 protection including electronic driver (SMPS based constant current supply with < 10% THD, output open/short circuit protection, phase to phase protection, over voltage protection, surge voltage protection etc) unit suitable for working volt 140-270 V AC, 50 Hz, pressure die cast aluminium housing and finishing epoxy white powder coated grey colur after phospho chromate treatment with all accessories and connecting up complete and all as specified and directed by Engr-in-Charge.Make : Crompton Geaves/ Bajaj/ Philips/Havells.
Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300 mm complete all as specified and as directed. Make : Crompton/Bajaj/Havells
Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and as directed.Make : Crompton/Bajaj/Havells
Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m complete all as specified and directed. Make : Bajaj/Crompton/Havells
M&L for metal clad AC socket point single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and as directed. Make : Legrand /Havells/Siemens
Supply and fix electric water heater storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed. Make : Havells/Bajaj/Crompton
Taking down Exh/Ceiling fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, painting of fans complete with superior quality synthetic enamel paint by spraying including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades, hanging/ fixing the fan in its original position and testing on completion complete all as specified and as directed.
M&L for MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with copper bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed. Make:- Legrand or equivalent in ABB/Siemens
M&L for MCB SPN 40-63 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed. Make:- Legrand or equivalent in ABB/Siemens
M&L for MCB SP 6-32 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed. Make:- Legrand or equivalent in ABB/Siemens
Taking down burnt unsv LT UG cable of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 25 sq mm, 2 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items. Make of Cable Havells/Polycab/Finolex
Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft/ loose soil complete all as specified and as directed.
Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all complete all as specified and as directed.
Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all complete all as specified and as directed.
M&L for spread fine river sand in trenches complete all as specified and as directed. NOTE: For measurement purpose, punned down thickness shall only be taken.
M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed
Supply & laying tubes ' Light grade' galvanised, with all fittings, fixed complete to walls, poles, ceilings for protection of cables of size 40 mm dia bore including taking out unsv GI tubing complete all as specified and as directed. Make:- Jindal/TATA/Prakash surya
M&L for point wiring with 1.5 Sqmm (nominal area) pvc insulated and un-sheathed single core FR-LSH copper cable 1100 Volts grade with multistranded copper conductor in and including PVC rigid concealed conduit (medium grade) and conduit accessories and sunk modular MS box for mounting of fitting alongwith continuous earth wire 1.5 sqmm PVC insulated and un-sheathed single core FRLSH cable 1100 volts grade with multistraded copper conductor and connected to common earth dolly including necessaru cutting chase of wall and making good to match with existing surface complete for Make of wire : Richa/RR Kabel/Finolex Make of PVC Conduit: Supreme/ Ori-Plast/ finolex/Richa
One light/Fan/Exhaust point controlled by one, one way switch .
One Call Bell point controlled by one, one way switch .
One 3 pin socket outlet 5 Amps on the same board with other switches.
One 3 pin socket outlet 5 Amps on the Independent board.
All as per item No- 200 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed.
All as per item No- 200 here-in-before but with 4.0 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 4.0 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed.
M&L for Modular Switch 1 way 6A,1 module Make : Havells/Legrand/Anchor
M&L for modular switch 1 way 16A, 1 module Make : Havells/Legrand/Anchor
M&L for Modular Socket ,6A/2/3 pin combined 2 module Make : Havells/Legrand/Anchor
M&L Modular Socket ,6A/16A-2/3 pin combined 2 module Make : Havells/Legrand/Anchor
M&L for Modular Bell push 6A 1 module Make : Havells/Legrand/Anchor
M&L for Bell Multi Music type Make : Havells/Legrand/Anchor
M&L for stepped type electronic fan regulator,120 W-2 module Make : Havells/Legrand/Anchor
S&F for White cover plate with frame 2 Module complete all as specified and directed.
S&F for White cover plate with frame 3 Module complete all as specified and directed.
S&F for White cover plate with frame 4 Module complete all as specified and directed.
S&F for White cover plate with frame 6 Module complete all as specified and directed.
M&L for MCB Distribution board double door type SPN 12 way, sheet steel, powder painted, with neutral link & earth bar etc. and fixing MCBs of various rating capacity MCB DBs complete all as specified and as directed. Make : Legrand /Havells/Siemens
Supply and fixing MCB SPN 63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed. Make : Legrand /Havells/Siemens
Supply and fixing MCB SP 6-32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed. Make : Legrand /Havells/Siemens
M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed.
S&F installation and testing and commissioning of Split type inverter Air conditioner of capacity 1.5 ton rating 5 star with cordless remote operated on 230 Volt AC supply complete to wall with suitable bracket for indoor outdoor unit and connected with electric suply, testing on full load complete all as specified and directed. Make : Voltas/Blue star/Godrej/LG
Supply and ffixing Voltage stablizer for automatic operation single phase indoor type and designed for input variation between 90-300 volts with digital disply out put voltage stabliser at 230 Volts with energy of± 2.5 % and of capacity for 2 Ton. Make : Microtek/V-gurad/Voltas.
VIHUTO YEPTHO
Shri Atoshe Tuccu
M/S MUNGA LAL PRASAD
M/S ARVIND GROUP OF CONSTRUCTION & INFRASTRUCTURE
M/s MATRI ENTERPRISES
commercial enterprises
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .