SPECIAL REPAIRS TO BLDG NO P28 AND P47 OF MSL REGT UNDER GE NARANGI

Amount

Dismantling timber boarding, any description, fixed in any position with nails as directed and removing rubbish off the premises complete all as specified and directed.

Dismantling of wall & celling boards (fiber pulp insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets and removing rubbish off the premises complete all as specified and directed.

Dismantling timber scantling 40 sq cm & over in section , any position in unframed work and removing rubbish off the premises complete all as specified and directed.

S & F aluminium Anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestor E-board, HSPC fixed to frame complete all as specified and directed.

M & L Preparing new ceiling and applying three coats of white wash complete as specified and as directed.

Taking up or down steel tubing & connections including clearing for refixing on removal to site of 15mm bore dia of pipe complete all as specified and directed.

Cutting chase, pinning in making good to faceing where required and pointing in cement mortar 1:3 to ends or edges of landing, and cutting chase for concealed water tubing or concealed conduit wiring etc and making good cutting exc 10cm but n exc 20cm and removing rubbish off the premises complete all as specified and directed.

Taking up or down steel tubing & connections including clearing for refixing on removal to site of 20mm bore dia of pipe complete all as specified and directed.

Dismantling water tanks and removing to site of capacity exc 250 but n exc 500 lt all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removing rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced) exc. 15 cm thickness above ground floor complete and removing rubbish off the premises complete all as specified and directed.

M & L for rendering 10mm thick in cement mortar (1:3) on fair faces of brick work and finishing the surface even and smooth with WPC without using extra cement as in sunken floor and wall complete all as specified and as directed.

Supply only integral water proofing compound

M & L for applying two coats of water proofing coating by using super latex manufactured by pidilite industries limited (or equivalent product manufactured by Sika/fosroc/choksey chemical), water and cement ratio 1:4:7 or the ratio as instructed by manufacturer on sunken floor and wall complete all as specified and as directed.

M & L plain cement concrete(1:3:6) type C-1(using 20mm graded stone aggregate) as in sunken floor complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n exc 15cm thick ness (below or above ground level) and removing rubbish off the premises complete all as specified and directed.

Demolition of brick work or stone boulder masonary built in cement morter and removing rubbish off the premises complete all as specified and directed.

Demolition of reinforcement cement concrete of any description and in any position not other wise as specified and removing rubbish off the premises complete all as specified and directed.

Dismantling of 100mm dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches if required and removing rubbish off the premises complete all as specified and directed.

S & F 20 mm thick, second class hard wood boarding clean sawn, planed one side with butt joints and fixed with nails in any situation as in eaves board, etc complete as specified and directed.

S & F 25 mm thick, second class hard wood boarding clean sawn, planed both side with butt joints and fixed with screw or nail in cupboard shelf, sutter etc complete as specified and directed.

M & L PCC typeC-1,1: 3:6 (20mm graded stone aggt) for cills,hold fast filling of hollow of pressed steel door frame etc complete all as specified and directed.

S & F solid PVC door frames of sizes 50mm x 47mm made out of 5mm but single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with MS Square tube complete all as specified and as directed.

S & F factory made solid panel PVC Moulded door shutter 28 to 30mm thick (styles), with 2,4, or 6 raised panel design with 2mm thick moulded PVC sheet on the frant face and 2mm plain coor PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing

S & F 75mm long butt hings medium weight cold rolled mild steel & fixed to pvc chowkats all as specified.

S & F 150mm long aluminium handle cast type anodised complete all as specified and directed.

S & F 150mm long aluminium anodised barrel towe bolt of extruded section complete all as specified and directed.

M & L 2nd class hard wood, solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put to gether with glue pinned at joints complete all as specified and directed.

Preparing surfaces of wood & wood based materials, new or old, of any description & girth, not otherwise described & treated with Raw linseed oil complete all as specified and directed.

S&F 18-19mm thick praticle board medicum desnsity, flat pressed single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work as in shelves complete all as specified and directed.

S&F pre laminated particle board interior grade prelaminated one side with decorative choice lamination & other side blancing white lamination fixed with screws to timber frame work as in shutter of cup board and other similar work (18/19 mm) complete all as specified and directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) Exc 1.5 Sqm but n. exc 4 Sqm Each complete all as specified and directed.

M&L for anodized aluminium push pull type partly panelled and partly glazed door shutter (single leaf / double leaf) having top rail of section 85.00 mm x 44.45 mm x 2.00 mm, bottom rail of section 85.00 mm x 44.45 mm x 2.00 mm thick, door verticals of section 44.45 mm x 44.45 mm x 2.00 mm thick and lock rail of section 85.00 mm x 44.45 mm x 2.00 mm thick with aluminium anodized chowkats of section 63.50 mm x 33.10 mm x 2.50 mm thick including necessary jointing cleats, glazing clips, rubber packing, snap beading, screws, handle and locking arrangement etc., including 12 mm thick pre laminated particle board, interior grade pre laminated with decorative face laminations both sides on bottom panel and 5.5 mm thick float glass tinted quality on top panel and including 1 No of aluminium door closer per leaf (Diecast) body hydraulically regulated, designation No. 3, universal type complete all as specified and as directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) not exc 1.5 Sqm Each complete all as specified and directed.

S&F aluminium anodised fixed /sliding type widow/ventilators frame section 32x92(three channels)mm all are made of from aluminium anodised section including necessary track jointing cleat glazing clips rubber packing anodised aluminium snap beading scres of suitable size including 4mm thick glasslocking arrangement including aluminium grill (6 mm dia minimum) of size 60x60mm complete all as specified and directed.

M & L two coat of synthetic enamel paint over one coat of pink primer,on wood surfaces of any description , not other wise described, over 10cm width or girth including preparation of new surfaces complete all as specified and directed.

M & L for applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surface & applying one coat of red oxide, zinc chrome complete all as specified and directed.

S&F Harrison rails,anodised aluminium alloy, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed.

S & F stainless steel wire cloath 0.36mm nominal dia and average width of aperature 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in Each panes complete all as specified and directed.

S & F 3.0mm thick figured glass, pin head type and glazing with oil putty in squqren exc 05Sqm Each pane complete all as specified and directed.

M&L 25mm thick PCC type B-1, (1:2:4) using 20mm graded stone aggregate complete all as specified and directed.

Dismantling floor, hearth wall tiling incld cement mortar bedding (but not backing) removing servicable tiles to store & rubbish off the premises complete all as specified and directed.

S&F Coloured Glazed ceramic tiles in vertical surfaces 350x250mmx7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick plaster in CM(1:4) complete all as specified and directed.

M & L for coloured ceramic tiles 7 mm thick (square/rectangular), area of Each tile exc. 0.18 Sqm but n. exc. 0.38 Sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

All as per item no 45 above as in vertical surface laid over and including 10 mm thick backing coat in CM 1:4.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded & jointed with grey cement slurry & pointed with white cement with admixure of pigment to match the shade of granite stone including cutting & polishing over and including 15mm thick screed in CM(1:4) complete all as specified and directed.

S & F 15mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed.

Fixing only tubes, 15mm bore galvanised with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and as directed.

S & F 20mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed.

Fixing only tubes, 20mm bore galvanised with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and as directed.

S&F in repairs Bib taps 15 mm bore, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair Stop valves 15 mm bore fancy type, CP, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair Stop valves 15 mm bore fancy type, CP with long shank & cup (conncelaed type), cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F vitreous china Semi pedestal pattern (Anglo Indian type) white connection to trap 'P' or 'S' and flush pipe etc seat cover and making good to disturbed surfaces of floor by filling with PCC 1:4:8 type D-2 to match with existing including taking down the existing old one all as specified and as directed.

S & F 110mm bore PVC branch pieces, single (Single Y) equal or un equal complete all as specified and directed.

Supply & Fixing in repairs 10 Litre capacity, PVC valves, syphonic action type, low level flushing cistern, white, with inlet ball valve, float and handle including brackets, complete all as specified and directed.

S & F PVC connection pipe 15mm size with PTMT nuts of 600 length including fixed in repairs complete all as specified and directed.

S & F towel rail 600mm long of PTMT fixed with and including chrominium plated brass screws and wooden/plastic cleats (Min wt 190 Gms) complete all as specified and directed.

S &F swivel shower of PTMT any colour for fixing with 15mm dia pipe (Min weight 40 gms) complete all as specified and as directed.

Supply & Fixing in repairs Vitreous china wash hand basin size 550x400mm (flat back or angle back type) including 32mm dia brass chromium plated waste fitting a pair if cast iron bracket duly painted /erecting stand including cutting and pinning in ends making good disturbed surfaces in CM 1:3 complete all as specified and as directed.

S&F CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and as directed.

S &F shower arm 15mm size 195mm long with bend of 45 degree with flange of PTMT any colour (Min weight 40 gms) complete All as specified and as directed.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers & wastes; including bedding in CM on to dwarf wall or including fixing cantilever brackets & connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed. Make : Nirali/Blustar/Prayag

Supply & Fixing Rotational moulded polyethene water storage tanks 500 litre capacity with lid (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part-I , complete all as directed by Engr-in- Charge

S & F Ball valves highpressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe complete all as specified and as directed.

M & L 10mm thick rendering on fair faces of brick work or concrete surface in cm 1:6 to be finished even and smooth with out suing extra cement.Including all as specified and directed

M & L 10mm thick rendering on fair faces of brick work or concrete surface in cm 1:4 to be finished even and smooth with out uing extra cement all as specified and directed.

M & L rendering 5mm thick in CM 1:3 and finish the surface even and smooth without using extra cement as in ceiling, soffits of slab complete all as specified and as directed.

M & L two coats of distermpering walls with distemper oil emulsion over white cement based wall care putty ( minimum 1 mm thick) on newly plastered wall surfaces including preparation of surfaces complete all as specified and as directed..

Complete removal of existing treatment on old surfaces on walls and applying two coats of distermpering on walls with distemper oil emulsion over white cement based wall care putty ( minimum 1 mm thick) complete all as specified

M & L one coats of white wash on old surfaces on ceiling including preparation of old surfaces.

M&L for preparation of new plastered surfaces of wall, any description, washing rubbing down and applying two coats external weather proof acrylic paints (Ist quality) over white cement based wall care putty (minimum 1.0mm thick) and primer etc all as specified and directed.

M&L for complete removal of existing old treatment of wall of any description and preparation of old surfaces ,washing rubbing down and applying two coats weather proof acrylic paints (Ist quality) over a coat of white cement based wall care putty(minimum 1.0mm thick) and primer etc all as specified and directed.

M & L PCC (1 : 2 : 4) type B-1, 40mm thick as in floor & finishing the surface even & smooth using extra cement etc complete all as specified and directed.

S & F 3mm thick 38mm width glass dividing strip and inserted in position to coform to design complete all as specified and directed.

M&L for 75 mm thick Cement concrete type C 1, 1:3:6 (using 20 mm graded stone aggregate) in plinth protection, finished even and smooth without using extra cement, including provision of joints and filling the same with bitumen mastic complete all as specified and as directed.

M & L PCC1:2:4 type B-2 (100 mm) thick ( 40mm graded aggregate) thick as in footpath & finishing the surface even & fair whtiout using extra cement complete all as specified and directed.

Forming Contraction (Dummy) joints 65mm deep x 10mmn wide,filled with sealing compoulld grade 'A' complete all as specified and directed.

M& L Chequered cement concrete tiles with grey cement and pigment of size 20cm x 20cm x 25 mm thick set, jointed and pointed in neat cement sluny in floors complete all as spercified over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for mild steel bars 10mm dia and over TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia

All as per item No 82 above but 5mm dia and over upto 10mm dia as in stirrups, spacers and binders

M & L precast cement concrete type A-1, 1:1.5:3 (20mm graded stone aggt) in landing, cover slabs(for man holes) and similar articles and set in CM 1:6 including necesarry formwork complete all as specified and directed.

M & L RCC type A-1, 1:1.5:3 (20mm greded aggregate) for slab supported on wall, beams, cantilevers and columns in floor, roofs, landing, balconies, etc complete all as specified and directed.

Formwork to soffits of suspended slab such as beams, lintels, cantillvers, shelves, pillars, posts, column , roof slab, floor slab, landing and similar work; flat rough finished surfaces of concrete.

Taking down of existing roof treatment from roof and Terrace, roughening surface of old concrete roof by picking, sweeping clean and washing down with water to remove dust, etc and applying roof treatment with the following specifications:- (a) Applying cement slurry over concrete surfaces @3kg/Sqm. (b) Rendering 20mm thick in cement mortar (1:4) mixed with water proofing compound as per manufactures instruction on cleaned concrete surfaces of roof and finishing the surfaces fair and even including curing the plastered surfaces for 7 days by ponding of water over the roof, (levelling course). (c) Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight). (d) Applying evenly one coat of cold bituminous primer conforming to [email protected] litre per square metre on the cleaned plastered surfaces. (e) Applying evenly one coat of blown hot bitumen of grade 85/25@ 1.20 Kg per square metre on primed surfaces. (f) Applying a layer of APP based polymeric membrane, 3mm thick (minimum) weighing 3.50 Kg per square metre reinforced) with polyester non woven fabric weighing not less than 160 gms per square metre by torch application. The overlap shall not to be less than 100mm on transverse direction and 75mm on longitudinal direction and sealing overlaps. (g) Applying evenly one coat of aluminium paint @ 0.10 litre per square metre over the APP based polymeric membrane.

M & L PCC 1:2:4, type B-0, (using 12.50 mm graded stone aggregate) as in under layer of roof treatment to provide gradient and slope finishing the surfaces rough to receive morter complete as specified and directed.

M & L brick work with sub class -B bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete as specified and directed.

S & F 110mm bore PVC Pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor complete as specified and directed.

S & F 75mm bore PVC Pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor complete as specified and directed.

S & F 110mm bore PVC Pipes single socketed, in any length with rubber ring joints, fixed to walls complete as specified and directed.

S & F 75 mm bore PVC Pipes single socketed, in any length with rubber ring joints, fixed to walls complete as specified and directed.

S & F 110 mm bore PVC (SWR) bends any radius complete as specified and directed.

S & F 75 mm bore PVC (SWR) bends any radius complete as specified and directed.

S & F 75mm bore PVC (SWR) floor trap,with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete as specified and directed.

S & F 110 mm bore PVC (SWR) vent cowl.

Cleaning of block drain pipe (SGSW/hume pipe) upto 150mm dia by rodding from manholes and well flushing with water after cleaning the same all as required and including disposing off the deposited sludge , etc inside pipes to a distance exc 50 m & n.exc 200 mtr burried under ground (minimum 30cm below ground level) including necessary excavating of pitsin soft/ioose soil and returning filling in including sprinkling of blEaching powder @ .20 Kg/Sqm and dressing of surplus soil around slope all complete as required and directed.

Cleaning of manholes including taking out accumulated Semi liquid, sludge and other deposits such as broken bricks, silt etc from manholes of depth n.exc. 1.5 mtr, cleaning as directed and removing the same to a distance n.exc 50 mtr and burried under ground(min 30 cm below ground level) including necessary excavation of pits in soft/loose soil and returning, filling in including , sprinkling of blEaching powder @ 0.20 Kg/Sqm and dressing of surplus soil around to slope, all complete as required and directed.

Cleaning blockage in nahani trap in bathroom kitchen or blocked gully trap by using rubber hand pump and opening the eye and making the line clear for smooth function al as directed.

Cleaning of open shaft of Md accn Bldg including gully trap, cleaning with wire brush including of grass, roots,bushes etc and taking out accumulated garbage etc, from shaft and removing the same to a distance n. exc 50m as specified and as directed.

S&F Framed work of steel fe 410 w grade 250 as in guard bars of windows purlins doors or gates of angle or other section with gusset plates rails braces complete drilledused in structural work all as specified and directed

S&F Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Dismantling timber scantling under 40sqcm in section in fillets, rails, rafter, purlins etc fixed with nails/screw etc complete all as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering etc complete all as directed.

M&L for PCC 1:3:6 type C2 (40mm graded stone aggregate) in foundation filling and mass concrete etc complete all as directed.

M&L for reinforced cement concrete 1:1½:3 type A1(20mm graded stone aggregate) nominal mix as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete etc complete all as directed.

Use and waste form work to to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work; vertical or to batterhorizontal or sloping flat rough finished surfaces of concrete

M&L for Brick work masonry using class 'B' old sized bricks straight or curved on plan exc 6m mean radius and built in CM 1:6 etc complete all as directed.

M&L for clean sawn 2nd class hardwood in scantlings etc complete all as specified and directed.

S&F Mild steel of conforming to Fe 290 grade E-165 as in wind ties fixed at eaves and ridge level etc complete all as directed.

S&F steel windows with side hung shutters glazed shutter including projecting type hinges with steel handle and steel peg stay with glazing bars and 12 mm square bar or ground bar of approved design welded to steel window frame dovetailed or welded complete all as directed.

S&F steel ventilator with top hung shutter glazed shutter including projecting type hinge with steel handle and steel peg stay complete with glazing bars and 12 mm square bar or ground bar of approved design welded to steel ventilator frame dovetailed or welded complete all as directed.

S&F, in position suspended false ceiling using E-Grid (exposed ceiling suspension system) of grid size 600mmx600mm with main runer 38x24mm, cross tee 27mmx24mm& wall angle 20mmx24mm. Using 4mm/6mm thick High pressure Steam cured Everest Non Asbestos Fibre cement Designer Board (E Board Classic) of M/S Everest Industries Ltd as per IS 14862 of M/S Everest Industires Ltd to be placed in a grid of GI system duly suspended with 4mm/6mm dia GI/MS bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip provided positions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of Each main runner should not be placed at more than 450mm from the adjacent wall, Flush fitting 1220mm cross tee to be interlocked between main runners @ 610mm c/c, so as to form 600mmx600mm/1200mmx600mm grid, all complete as per the drawing & directions of Engineer-in-charge.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screws, in roofs, walls etc with grade of zinc coating 120 etc complete all as directed.

S&F 0.63mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 120 etc complete all as directed.

M&L for 15 mm thick rendering in CM 1:4 on brick/concrete external surfaces and finishing the surfaces even and FAIR without using extra cement etc complete all as directed.

S&F Rolled mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lenghts i.e. within 20mm of the length indicated) GDE Fe 410-0 W (Gde E-250) quality A

S&F Rolled mild steel Plates (plain or chequered) channels. Square cut or notched (ordinary & counter sunk) forming holes, with riveted, bolted or welded attachment GDE Fe410-0 or Fe 310-O

S&F Mild steel screw bolts (machine made) with hexagonal / square heads at one end & screwed the other/ screwed both ends, Each screwed end to be fitted with washers & one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm long dia of shank 16 to 20 mm

Taking down carefully aluminium/ copper point wiring for light/fan/ socket/bell or power point incl. All fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. complete removing materials to store for keeping in safe custody site or handed over to contractor as schedule of credit and making good disturbed surfaces of walls, floors, etc complete all as directed by Engineer-in-Charge.

Taking down ceiling/exhaust/wall fan including connection wires carefully ,removal to store in safe custody and refixing the same in original position after repairing (rewinding if requre) ,painting with synthetic enamel paint by spraying incl. filling cavity complete all as directed by Engineer-in-Charge.

M&L for concealed point wiring for modular fittings with 1.5 Sqmm (nominal area) PVC insulated1100 volts grade, multistranded, copper conductor, single core, unsheathed cables (FRLSH quality) drawn through and including PVC conduits of suitable size but not less than 20 mm dia (medium grade) with all fittings and accessories concealed in walls/ceiling etc including cutting chases for conduits and including suitable module modular boxes ( 1.6 mm thick powder coated MS sheet or PVC) , cover plate with frame and making good to disturbed surfaces including PVC insulated and unsheathed, single core, multi-stranded, copper conductor cable of size 1.5 Sqmm green in colour as earth continuity conductor connected to common earth and earth dolly for one light point / fan point/ one call bell point controlled by one 5 Amps one way switch complete as specified and directed. Note : Quoted rate shall be inclusive for necessary chasing and cutting and making good .

All as per item serial No 123 here-in-before but One 3 pin socket outlet 5 amps on the same board with other switches

All as per item serial No 123 here-in-before but One socket outlet 3 pin 5 Amp on independent board.

All as per item no 123 here-in before but one light point controlled by 2-way switches.

All as per item serial No 123 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 2.5 Sqmm cable.

All as per item serial No 123 here-in-before but with 4 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 4 Sqmm cable.

Supply and fixing of modular switch, one way 6 amps, 1 module 240 Volts complete all as specified/directed. Make : Legrand/L&T/Schneider

Supply and fixing of modular switch two way 6 amps 1 module 240 Volts complete all as specified/directed. Make : Legrand/L&T/Schneider

Supply and fixing of modular socket outlet 2/3 pin 6 Amps 240 volts 2 module complete all as specified/ directed.Make : Legrand/L&T/Schneider

Supply & fixing of modular switch one way 16 Amps 1 module 240 Volts complete all as specified / directed.Make : Legrand/L&T/Schneider

Supply and fixing of modular socket 6/16 Amps, 2/3 pin combined, 2 module complete all as specified and directed.Make : Legrand/L&T/Schneider

Supply and fixing of modular bell push switch, one way 6 amps, 1 module 240 Volts complete all as specified/directed. Make : Legrand/L&T/Schneider

S&F ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as directed

Supply anf fix lamp holder ,PVC/Polycarbonate type with back plate suitable for batten fittings.

S&F decorative hexagonal bulk head fitting with LED luminaire 10Watt,6000K with IP 65 Protection including connection complete all as directed.

S&F electronic stepped type electronic fan regulator, two module size flush type complete all as directed. Make : Legrand/L&T/Schneider

S&F call bell Ding Dong AC, 230 volts single pole complete all as directed. Make : Legrand/Havells/L&T/Schneider

S&F Plug and socket DB with industrial socket suitable for 3P+1N+1E complete with MCB FP 63 A Model DX3 and plug in socket 5 pin suitable for 415 volts complete all as specified and directed .

Supply and fix LED box type fitting pre-wired including LED tube 1x10W connecting up with PVC insulated and sheathed 1100 volt grade flexible copper cable and fix on PVC block complete all as directed. Make:- Jaguar Model-LGLZ01X010XC/ LGLZ01X010XN/LGLZ01X010XW or Make:- Havells Model-LUMILINEPLUSBS10WLED865SPCSS or equivalent model of make Philips /GE/Cromptonor equivalent model of make Philips /GE/Crompton

Supply and fix LED box type fitting pre-wired including LED tube 1x20W connecting up with aluminium housing and sheathed 1100 volt grade flexible copper cable & fix on PVC block complete all as directed. Make:- Jaguar Model-LGLZ01X020XC/ LGLZ01X020XN/LGLZ01X020XW or Make:- Havells Model-LUMILINEPLUSBS20WLED865SPCSS or equivalent model of make Philips /GE/Crompton

S&F wall decorative fixture in durable plastic body &designer mesh in gold finish suitable for 9W LED lamp of B-22 ,including lamp of 9watt .Complete as directed as specified .Make -Havells cat no-LHFOECE1TZ1B014 or equivalent

S&F as in repair factory made, sheet steel distribnution boards, double door, protection class IP-42, SPN 8 Ways suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 200 Amp rating copper bus bar, complete all as directed.

S&F as in repair factory made, sheet steel distribnution boards, double door, protection class IP-42, DB TPN 4 Ways suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 200 Amp rating copper bus bar, complete all as directed.

S & F MCB SP 6- 32Amps, 240 V,50 HZ,C series breaking capacity 10KA all as specified and directed.

S & F MCB TPN 63Amps, 415V,50 HZ,C series breaking capacity 10KA all as specified and directed.

Supply MCBs, SPN 40 to 63 Amps, 10 KA , IS/IEC 60898-12002 marked fixing in DBs (DBs catered separately in this Schedule) Make:-Legrand ,cat part no-4086 09 to 17 or equivalent

Supply MCBs, SPN 6 to 32 Amps, 10 KA , IS/IEC 60898-12002 marked fixing in DBs (DBs catered separately in this Schedule) Make:-Legrand ,cat part no-4086 09 to 17 or equivalent

Taking down old unserviceable sub main wiring and M&L for Sub main wiring with Two runs of 6 Sqmm size main cable of single core PVC insulated but unsheathed FRLSH cable size with multi standed copper conductors, 1100 volts grade, IS-694 marked with the one run of 6 Sqmm size of earth continuity conductor of similar type cable all drawn through and including suitable size PVC conduit and fittings/accessories all fixed to the surface of wall/ceiling complete all as specified.

Supply,installing,connecting and testing AC single phase static energy meter of Accuracy class 1.0, 240V,50Hz with backlit LCD display,of rating 10 to 60 Amp(Measure and displays in kWhV,I,kW,PF Last month history of kWh & Md in kW) with special features like TOD, Tamper logging,Optical communication port & display in absence of power with transparent hinge type box including taking dowm old metre and depositing the same in MES store yard of AGE E/M complete all as specified and directed. Make- L&TCat part No-WM101BC7DDHBOX or equivalent .

S&F anticorrosive ,dust proof ,rust proof,shock proof ,self extinguishing property ,resistant to heat & water proof ,ultra voilet stabilized and pilfer resistant to accommodate 4 Nos single phase meter made from thermosetting plastic i.e glass reinforced polyester sheet moulding compound (smc) conforming IS : 13410 (1992) as per attached technical specification ,by the process of hot compression moulding drawing and IS 14772 : 2000 of minimum size of box from inside shall be 370x270x210 mm and making good disturbed surface using necessary plaster work complete all as specified and directed.

Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion including taking down old one all as specified and shown on plate No 3 of SSR Part-I 2009.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 4 core .

Excavation in trenches in soft/loose soil not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide for laying of cable and erection of poles all as specified and directed at site.

Removing excavated material not exceeding 50 m and depositing at a level n.exc 1.5 m above the starting point all as specified & directed by Engineer-in - Charge.

Returning, filling in including spreading, levelling, watering and well ramming excavated soft/loose soil in layers , all as specified and directed at site

M&L for sand cushioning to under ground cable using locally available fine clean dry river sand over, under ground UG cable laid in trenches and gently punning done complete all as directed by Engineer-in-Charge. Note : For the purpose of payment only punned thickness will be measured.

Material and labour for bricks for protection of underground cables with sub class ‘B’ over burnt brick, (locally available best quality), laid dry and flat abutting Each other with gaps not exceeding 10mm complete all as specified and as directed.

S&F in repairs 34 watt LED recessed mounted luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling and fixture size in mm (LxWxH) 595x595x70 complete all as specified and directed.Make : Havells Model-PLUTONEO2x2PLR34WLED840S/ PLUTONEO2x2PLR34WLED857S or equivalent model in make of Philips/ Crompton/Bajaj

Supply fix MCCB DB IP-43 of sheet metal enclosure double door VTPN 4 way with 250 Amps rated copper bus bar 415 volt and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and as directed.

S&F MCCBs 415 V, 16 KA, 4P, 100 Amps complete all as directed.

M&L LED building secruity luminaries 48 Watts WSPD epoxy powder coated pressure die cast aluminum housing with wheatherproof gasket for LED's and control gear compartments, pressure die cast aluminium frame with heat resistant toughened clear glass fixed with SS screws LED Specification: CREE LED/Equivalent, Colour temp - 5700 K +/- 300 K Lens,,IP-66,Lumen efficiancy >100 lm/w,surge protection 4kv internal (Built-in) with twin core conductor complete all as directed including testing on completion. Make: Havells CAT No. ENDURAPEARNEOSL48WLED757SASYTOPC or equivalent of Philips/Wipro/CG.Note-Driver of LED street light should be same as make approved.

M&L for building secruity light bracket made out of 40 mm bore medium grade GI Pipe with two sets clamps, with nuts and bolts, bend to shape for fixing street light luminaries all as directed, length of GI Pipe shall not be less than 2.0 mtrs complete all as specified and directed.

Earthing complete with copper earth plate electrode of size 60cm x 60cm x 3.15 mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including copper earth strip of size 20x3 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 25 mm dia GI pipe connected to main control board and GI pipe medium grade 20 mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion including taking down old one complete all as specified and shown on plate No 3 of SSR Part-I 2009

S & F as in repair for aluminium strip 25 x 3.15mm with saddles and fixing screws etc for roof conductors and down conductor above ground complete all as specified and directed by Engr-in-charge.

M & L as in repair for test point teminal block made of gun metal or phosphorus bronze size 75x75x25 mm ,drilled and screwed including 3 nos 8 mm 25 mm long hex. Head screw complete all as specified and directed by Engr-in-charge.

M & L as in repair for Lighting conductor of Air terminal , single pointed ,Aluminium rod 12mm dia and 300 mm long to be fixed on horizontal lighting conductor with suitable fixing arrangement complete all as specified and directed by Engr-in-charge.

M & L as in repair for fabrication of display board for earth pit nos,location and perodical test results for lightening arrestor earthing made of M S sheet 4.0 mm thick ,rectangular welding on 12 mm dia roof of height from ground level 30 cm including fixing in PCC 1:2:4 with 20 cm x 20 cm x 20 cm (below ground level ) grade aggregrate foundation .Dimension of board shall be 30 cm x 25 cm .The instruction shall be written black painted board in white letters not less than 2" size for all type of board complete all as specified and directed by Engr-in-charge. Note- All necessary MS sheet ,aluminium screws and PCC works etc are deemed to the rate quoted by the contractor.

S & F as in repair for thermoplastic (polycarbonate ) junction box for test point without terminal block of dimension 130x 180 x 77 mm IP 66 halogen free and water proof including four hexagonal anticorrosive screws for out door installation with suitable fixing arrangement complete all as specified and directed by Engr-in-charge.

LAXMI CONSTRUCTION

K Eswar Chandra

M/S MANOJ PAUL

M/S SEWAK SINGH

M/S RAJ RANI BUILDERS

M/s KRISHNA CONSTRUCTIONS

M/S Bharat Construction