COMPREHENSIVE MAINTENANCE TO CERTAIN OMQ, OFFICER MESS, SINGLE OFFICER ACCOMMODATIONS , CAMOUFLAGING TO BUILDINGS, ROOFING AT BOUNDARY WALL, BP ETC AND OTHER MISC WORKS UNDER GE (AF) SRINAGAR

Amount

Contractor’s special attention is invited that work will be executed for up to triple story building. Quoted rates shall be deem to include for provision & removal scaffolding and necessary safety arrangement for workers employed

Demolition of cement concrete (unreinforced) in ground floor and in paving n exc 15 cm thickness (below or above ground level), complete all as specified.

M&L for 75 mm thick PCC type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection laid in bays n. exc. 2 sqm each, finishing the surface of concrete topping even & fair, without using extra cement filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand (all by weight) complete all as specified and as directed by Engineer-in-Charge.

Demolition of Brickwork or stone/boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius with old size bricks built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

M & L for Brick work with sub class ‘B’ bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

Taking down cement plaster / cast in situ terrazo of any description on brick walls or concrete surfaces etc. including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed by the Engineer-In-Charge.

M&L for Rendering 15 mm thick in cement and sand mortar 1:6 on brick work or cement concrete surfaces of walls including finishing the surface even and smooth with using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for Rendering 15 mm thick in cement and sand mortar 1:4 on brick work or cement concrete surfaces of walls including finishing the surface even and smooth with using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for Rendering 5 mm thick in cement and sand mortar 1:3 on concrete surfaces of ceiling, including finishing the surface even and smooth without using extra cement complete all as specified.

Demolition of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including rubbish off the premises, all as specified..

M&L 15 mm thick screed or bedding layer in cement mortar (1:4) for laying floor finishes, complete all as specified.

M&L for 10 mm thick rendering / backing coat in cement mortar (1:4) to receive wall tiles, complete all as specified.

M&L for 25 mm thick PCC 1:2:4 type B0, using 12.5 mm graded stone aggregate) as in sub base floor complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surfaces of size 600 x 300 x 6-7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over screed bed.

M&L for double charged colour vitrified ceramic tiles 10 mm thick (square) polished, area of each tiles n.exc 0.36 sqm in floors etc laid over existing screed bed, set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for double charged colour vitrified ceramic tiles 10 mm thick (square) polished, area of each tiles n.exc 0.36 sqm for skirting / dado etc laid over existing backing coat, set and jointed in neat cement slurry and pointed in white or coloured cement to match.

Demolition of RCC selves / cooking platform (reinforcement cut as required to facilitate demolition) and similar suspended work and removing debris form site all as specified and directed.

M&L for RCC 1:2:4 using, type B0, using 12.5 mm graded stone aggregate as in selves / cooking platform and similar work complete all as specified & directed.

Use & waste form work to soffits & side of selves / cooking platform flat, fair finished surfaces of concrete not exceeding 100 mm thick complete all as specified & directed.

M&L for mild steel TMT bars 10 mm dia and over cut to length bent to shape including cranking bending spirally for hooping for columns hooking end and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including half round molding of exposed edge complete all as specified.

S&F in repair Stainless steel plate rack made of 0.8 mm thick sheet, overall size 600 x 750 mm, with partitions, fixed to wall with PVC gutties and screws of suitable sizes, , complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 75 mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete.

S&F in repairs stainless steel sink, 1.00 mm thick for kitchen or laboratory, with plug, washers, waste pipe including bedding in cement mortar on to draft wall or including fixing cantilever brackets, connecting union to pipe etc, overall size 495 mm x 420 mm, with bowl size 405 mm x 355 mm x 178 mm, including waste assembly, complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm including waste assembly, complete all as specified and directed.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed by Engineer-in-Charge.

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed by Engineer-in-Charge.

Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 15 mm bore after cleaning including provn of new fittings all as directed by Engineer-in-Charge (using old steel tubing retrieved from item No 27 above).

Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 20 mm bore after cleaning including provn of new fittings all as directed by Engineer-in-Charge (using old steel tubing retrieved from item No 28 above).

S&F 15 mm bore tubes, 'medium grade', galvanised, with all fitting; (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed to wall / ceiling with clips, wall hooks, wooden plugs or laid in floors, complete all as specified.

S&F 20 mm bore tubes, 'medium grade', galvanised, with all fitting; (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed to wall / ceiling with clips, wall hooks, wooden plugs or laid in floors, complete all as specified.

S&F in repairs, 125 mm dia stainless steel chromium plated grating, fixed in position with white cement Complete.

M&L for cutting chases pinning in making good to facing where required and pointing in cement mortar (1:3) for concealed water tubing in brick walls cutting n.exc 10 cm girth. complete all as specified and directed.

S & F in repairs 15 mm size sink mixer for mixing hot & cold water, cast copper alloy chromium plated with quarter turn capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 15 mm size central hole basin mixer for mixing hot & cold water, cast copper alloy chromium plated with quarter turn capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe including 450 mm long braided connection pipe complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 15 mm size wall mixer for mixing hot & cold water, cast copper alloy chromium plated with quarter turn capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 15 mm size wall mixer with L bend for shower for mixing hot & cold water, cast copper alloy chromium plated with quarter turn capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair brass chromium plated Jet Spray of Standard size for EWC along with CP connection and all fittings as fixed, complete all as specified and directed by Engineer-in-Charge.

S&F in repair ABS plastic chromium plated Health faucet fixed with spring action and lever along with Flexible hose with brass nut of length 1 m to 1.2 m fitted in the existing water connection in the toilets, Complete all as specified and directed by Engineer-in-Charge.

S&F in repairs for 15 mm size angle cock fancy type, cast copper alloy chromium plated, with capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed, all as specified.

S&F in repairs for 15 mm size two way angle cock fancy type, cast copper alloy chromium plated, with capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed, all as specified.

S&F in repairs for 15 mm size bib taps long body, fancy type, cast copper alloy chromium plated, with capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed, all as specified.

S&F in repair PVC connection 15 mm size, of length 600 mm, with PTMT nuts complete all as specified and as directed by Engineer-in-Charge

S&F in repair Glass Shelf of size 500 mm x 125 mm wide with stainless steel wire guard fixed on wall with and including bracket and brass screws and wooden / plastic cleats.

S & F in repair Corner Glass Shelf of size 300 mm with stainless steel wire guard fixed on wall with and including bracket and brass screws and wooden / plastic cleats.

S&F in repair brass chromium plated shower roses with swill joints, 80 mm size in square with CP long shank arm including fixing to steel pipe or union, complete all as specified and as directed.

S&F in repair Tubular towel rail stainless steel chromium plated 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs white vitreous china squatting pan ‘ORISSA’ pattern of size 580 mm x 440 mm white with integral foot rests with ‘P’ or ‘S’ trap, front or back inlet including all connection and provision of lime concrete base complete all as specified and as directed..

S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, brass chromium plated Jet shower with one meter long flexible pipe including all connection complete.

S&F in repair PVC low level flushing cistern, valve less, Syphonic action type, double push bottom, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 32 mm dia of required length and making connection complete all as specified.

Supply and fix in repair white vitreous China wash hand basin (Flat back) of size 550 x 400 mm fixed on and including new brackets complete including, 32 mm size brass chromium plated waste coupling, chain and plug and porcelain stopper, etc complete.

S&F in repair Toilet paper holder cast copper alloy chromium plated fixed to walls with chromium plated brass screws, complete all as specified and as directed by the Engr-in-Charge

S&F in repairs Stainless Steel Soap dish, fixed to plugs with chromium plated brass screws Complete all as specified and directed by Engineer-in-Charge.

S&F in repair 32 mm size & 750 mm long PVC waste pipe flexible type for WHB / sink complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair 500 litres capacity double layer, rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete

Supply and fix in repair 1000 litres capacity double layer, rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete

Supply and fix in repair 2000 litres capacity double layer, rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete

S & F in repairs 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

M&L for Cleaning of HDPE service water tank of capacity up to exc 1000 liters, and the connected circulating pipes at any position by removing sludge, mud, moss, moulds, efflorescent salts, oil spots etc or any other foreign material from the bottom, cover and internal surfaces by scraping using wire brush, draining out the water from the tank and washing internally with water & bleaching powder (0.10 Kg of bleaching powder will be mix in 1 liters water) and again draining out the water from the tank and writing the date of cleaning with white synthetic enamel paint on black background with synthetic enamel paint complete all as directed by Engineer-in-charge.

S & F in repair Plastic water closet seat cover, white, closed pattern with flat bottom, and cover with aluminium hinging device

S&F Magnetic type catch fixed with screws to door frame complete all as specified and directed by Engineer-In-Charge.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised., width of flaps when open in 30 mm, complete all as specified and directed by Engineer-in-Charge.

S&F 20 mm Stainless steel curtain rod with stainless steel bracket and stainless steel finils, fancy type as approved by GE, as in curtain rods including taking down the old curtains rods complete all as specified and directed by Engineer-In-Charge.

S&F 40 mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed.

S&F in repair 100 mm size hasp and staple, stainless steel including bolt to hinge plate and fixed with screws in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 18 / 19 mm thick Block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work as in Kitchen drawers etc. including 4 mm thick teak wood lipping on edges complete.

S&F 0.90 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete.

Resecuring or easing & adjusting old wooden shutters of any description area exc. 1 Sqm and not exc. 2 Sqm each without taking down shutters, complete all as directed by Engr-in-charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.50 Sqm each complete all as specified and as directed by the Engineer-in-Charge

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 Sqm but n exc 4.00 Sqm each complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description, area exceeding 1 sqm and not exceeding 2.00 sqm each complete all as specified and as directed by Engineer-in-Charge

M&L for Pressed steel frames 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, lock strike plates complete, providing mild steel 6 mm dia thresh old bar and filling hollow of frame with plain cement concrete Type C-0, 1:3:6 (using 12.5 mm graded crushed stone aggregate) complete, all as specified.

M&L for Pressed steel frames 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, lock strike plates complete, providing mild steel 6 mm dia thresh old bar, thickness of sheet 1.25 mm and filling hollow of frame with plain cement concrete Type C-0, 1:3:6 (using 12.5 mm graded crushed stone aggregate) complete, all as specified.

S&F Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2020 as specified and as directed by Engineer-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in drawing of relevant item in MES, schedule Part-II , 2020 as specified and as directed by Engineer-in-Charge.

S&F 35 mm thick, IInd class hard wood plain, framed, paneled shutters (two panel) with lock rail and panel of 12 mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified & as directed by Engineer-in-Charge.

S&F 35 mm thick, 2 nd class hard wood, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.24(a) complete all as specified and as directed by Engineer-in-Charge.

S&F 30 mm thick, 2nd class hard wood, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.24(b) complete all as specified and as directed by Engineer-in-Charge.

S&F in repair IInd class hard-wood, small fittings such as bracket of any sizes, hinge blocks, cleats, door / window stoppers and like articles not exceeding 200 cubic centimeters each complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new wooden surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of primer complete all as specified and as directed by Engineer-in-Charge.

S&F 03 mm thick sheet glass, ordinary quality and glazing with oil putty / wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed by Engineer-in-Charge.

S&F 03 mm thick sheet glass, figured glass, pin head type and glazing with oil putty / wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Figured glass 4 mm thick, ordinary quality and glazing with rubber neoprene packing and aluminium glazing clip, complete all as specified and directed by Engineer-in-Charge. Note:- Old rubber bead & old aluminium glazing clip retrieved from demolition of glass shall be reused for fixing of new glass.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-Charge.

S & F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-Charge.

S&F 100 mm size butt hinges, stainless steel medium weight, complete all as specified and as directed by Engineer-in-Charge.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed by Engineer-in-Charge.

S&F 150 mm size, aluminium anodized handles, cast type complete all as specified and directed by Engineer-In-Charge.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified and as directed by Engineer-in-Charge.

S&F in repairs Floor door stopper of aluminium alloy body, double legged with rubber shoe fixed to door, Overall length of cover plate 100 mm all as specified and directed by Engineer-in-Charge

S&F in repairs 300 mm long mild steel ordinary rat tail rod pattern, door spring including roller and roller plate complete all as specified and as directed by Engineer-in-Charge.

S&F door strip length exc 0.90 RM but n,exc 1.20 RM, comprising of aluminium holds & rubber strip fixed at bottom of door shutter with screws complete all as specified and as directed by Engineer-in-Charge

M&L for Lagging to pipes 15 mm bore used in external water supply or plumbing all around with 50 mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25 gauge 20 mm mesh complete including taking down of old lagging all as specified and directed by Engineer-in-Charge

M&L for Lagging to pipes 20 mm bore used in external water supply or plumbing all around with 50 mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25 gauge 20 mm mesh complete including taking down of old lagging all as specified and directed by Engineer-in-Charge

S&F in repair particle boards or tiles of size 600 mm x 600 mm 12 mm thick for insulation and acoustic purposes, fixed or laid / inserted to timber / GI / Aluminium framework with screws, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new wooden surface ceiling board of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-In-Charge.

S & F in repair Non asbestos fiber cement building boards, manufactured from homogeneous mixture of cement, quartz and cellulose and cured with high pressure steam using auto claving process confirming to IS-14862, of size 600 mm x 600 mm x 6 mm thick fixed or laid / inserted to timber / GI / Aluminium framework with screws complete all as specified and directed by Engineer-in-Charge.

Dismantling of Plain or corrugated steel sheeting any gauge, thickness, in roof coverings including ridges, hips, valleys and flashings etc complete all as specified and as directed by Engineer-in-Charge.

S&F 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, with L-type or J-type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating 275 complete.

All as per item No 103 but except Sheets using sheet retrieved vide item No 102 above

S&F 0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275

M&L for Preparation of new zinc (or galvanised) steel and iron roof surfaces of any description over 10 cm width or girth to receive painting, by coating with mordant solution including washing and cleaning, etc and applying two coat of synthetic enamel paint over one coat red oxide primer complete all as specified and directed by Engineer-in-Charge

M&L for Easing of Aluminium shutters of door / CB / Sliding windows shutters, area exceeding 1 Sqm but n. exe 2.5 Sqm each (One unit shall comprise of one window / CB / Showcase irrespective of number of leaves) for easing and adjusting by tightening of joints, adjustment of tower bolts, sliding bolt etc for smooth function / properly closing / opening, complete all as specified and directed.

S&F in repair Vitreous China urinal half stall type, white, with grating and union for discharge pipe and including waste pipe(excluding flushing cistern), complete including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinals to plugs including 60 mm long brass screws including brass chromium plated urinal spreader for fixing with 15 mm dia pipe all as specified and directed by Engineer-in Charge

Material and labour 1st quality vitrified parking tiles of approved shade, of 9 to 10 mm thick, polished area of each tiles exceeding 0..08 sqm but not exceeding 0.16 sqm, as in floors / path etc, set & jointed in neat cement slurry & pointed in matching coloured polymer cement based grout to match complete. Make :Johnson Endura meteor (Korneto Biege) or equivalent make mention in Appx A.

M&L for welding in repairs exc 2.5 cm but n.exc 5 cm in length thickness of metal to welded n.exc 6 mm complete.

S & F in repair white vitreous china floor mounted coupled EWC of size 380 mm x 725 mm x 690 mm including UF soft close slim seat cover, hinges, fixing accessories, accessories set and Cistern Fittings complete all as specified and directed. Make of Cistern & EWC: Jaquar model No-ONS-WHT-10853S300UFSM or equivalent cat No of make mention Appx A.

M&L for Preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls including sides and soffits of beams, fascias, parapets etc and applying two coats of cement base paint over one coat of primer, colour and tint as ordered, complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation of Old decorated surfaces of wall including cleaning brooming down or with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts cleaning oil and greasy spots, trading oil, greasy spots etc and applying one coat of white wash complete all as specified and as directed.

M&L for Preparation of Old decorated surfaces of ceiling including cleaning brooming down or with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts cleaning oil and greasy spots, trading oil, greasy spots etc and applying one coat of white wash complete all as specified and as directed.

M&L for Preparation of old decorated surfaces of walls, pillars, cornices by brooming down or steel brushing, scraping down smoke roots. moulds , moss and efflorescence salts, trading oil greasy spots etc. and applying one coat of oil bound distemper after removal of nails & filling nail hole with putty complete all as specified and directed by Engineer-in-charge.

M&L for Preparation of old decorated surfaces of ceiling including cornices etc by brooming down or steel brushing, scraping down smoke roots. moulds , moss and efflorescence salts, trading oil greasy spots etc. and applying one coat of oil bound distemper after removal of nails & filling nail hole with putty complete all as specified and directed by Engineer-in-charge.

M&L for Preparation of old decorated surfaces of ceiling including cornices etc by brooming down or steel brushing, scraping down smoke roots. moulds , moss and efflorescence salts, trading oil greasy spots etc. and applying two coat of oil bound distemper after removal of nails & filling nail hole with putty complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old painted wooden surfaces of any description not other wise described over 10cm width or girth and applying one coat synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old painted wooden surfaces of any description not other wise described over 10cm width or girth and applying two coat synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old painted steel surfaces of any description not other wise described over 10cm width or girth and applying one coat synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge

M&L for preparation of old painted steel surfaces of any description not other wise described over 10cm width or girth and applying two coat synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge

M&L for preparation of old polished wooden surfaces of any description, width or girth, filling of crack / cavity with wood filler and applying one coat French polish complete all as specified and directed by Engineer-in-Charge

Complete removal of existing treatment from wall surface including pilister & cornice etc of any description including cleaning brooming down or with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts etc complete all as specified and as directed.

M&L for applying 3 mm thick cement base wall care putty in two coats on new plastered surface of wall / surface obtained after complete removal existing treatment from wall, and making the surface even & smooth for receiving distemper / paint of any description all as specified & directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over one coat of primer all as specified and directed. Note:- Cement base wall care putty where ever directed will be applied and will be measured & paid separately

M&L for preparation of new plastered surface of walls / walls surface obtained after complete removal of treatment and application of water based primer suitable for weather proof exterior emulsion paint, applied as per manufacturer instruction on wall surface including pilister & cornice etc of any description complete. Note:- This item will be executed over new plaster surface / surface obtained after complete removal of existing treatment.

M&L for application of two coats of exterior emulsion paint in camouflage pattern applied as per manufacturer instruction on premiered surface of wall including pilister & cornice etc of any description complete. Note:- Application of primer will be measured & paid separately.

M&L for preparation of surface obtained after complete removal of treatment from walls including sides and soffits of beams, fascias, parapets etc and applying two coats of cement base paint over one coat of primer, in camouflage pattern colour and tint as ordered, complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation of new zinc (or galvanised) steel and iron roof surfaces of any description over 10 cm width or girth to receive painting, by coating with mordant solution including washing and cleaning, etc and applying two coat of synthetic enamel paint over one coat red oxide primer in camouflage pattern complete all as specified and directed by Engineer-in-Charge

M&L for Preparation of old painted steel and iron roof surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint in camouflage pattern all as specified and directed by Engineer-in-Charge

M&L for Preparation of old painted wooden surface of any description over 10 cm width or girth and applying one coat of synthetic enamel paint in camouflage pattern all as specified and directed by Engineer-in-Charge

M&L for preparation of old decorated surfaces of walls, pillars, cornices by brooming down or steel brushing, scraping down smoke roots. moulds, moss and efflorescence salts, trading oil greasy spots etc and applying one coats of cement base paint over one coat of primer, in camouflage pattern colour and tint as ordered, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old decorated surfaces of walls, pillars, cornices by brooming down or steel brushing, scraping down smoke roots. moulds, moss and efflorescence salts, trading oil greasy spots etc and applying two coats of cement base paint over one coat of primer, in camouflage pattern colour and tint as ordered, complete all as specified and directed by Engineer-in-Charge.

S&F in repair second class soft wood Weather boarding, clean sawn, thickness 20 mm to 25 mm and rebated on thick edge to give 20 mm laps and fixed in eaves board etc complete all as specified and directed by Engineer-in-Charge.

S&F in reair 03 mm thick sheet glass, figured glass, pin head type and glazing with oil putty / wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed by Engineer-in-Charge.

M/S WANI AND SONS

M/S Abdul Ahad Rather

M/S RATHER CONSTRUCTION CO

M/S LATIF AHMAD MIR

M/S Thakur & Sons

M/S MAQBOOL BHAT & SONS

M/S KHAN ENTERPRISES