CWE/Y-88/2021-22

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Demolition of reinforced cement concrete ((reinforcement cut as required to facilitate demolition) in ground floor and paving n.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Demolition of brick work or stonework built in cement mortar including all quoins, arches pillars etc but excluding ashlar facings ,dressed stonework and precast concrete articles and stacking the serviceable materials within 100m and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Taking down cement plaster including backing etc from brick/stone walls / concrete surfaces including raking out joints, hacking for key , scrubbing down with water etc complete all as specified and directed

Taking down and removing chowkats with shutters (without taking off shutters from chowkat) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down and removing chowkats with shutters (without taking off shutters from chowkat) exc 1.50 Sqm but not exc 4.00 Sqm each complete all as specified and directed. .

Taking down steel water tubing 15 mm bore including all fitting and connections complete all as specified and directed.

Taking down steel water tubing 20 mm bore including all fitting and connections complete all as specified and directed.

Dismantling boarding , any description ,fixed in any position with nails complete all as specified and directed.

Dismantling timber in scantling 40 sqcm and over in section, framed work complete all as specified and directed.

Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling plain or corrugated steel sheets any gauge thickness including Nanital or similar pattern roof covering including ridges complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises. complete all as specified and as directed.

Dismantling water storage tank of capacity exc 250 ltr but n.exc 500 ltr complete all as specified and directed. .

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Plain cement concrete 1:2:4 ( nominal mix ) type B-0 (using 12.5mm graded crushed stone aggregates) as in cement concrete in roof kerbs or mud stops, rounded or chamfered on edges, lintels upto 1.5m clear span, cills, steps; seismic and other similar ands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary formwork where required complete all as specified and directed.

PCC 1:3:6 (nominal mix) type C-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

PCC 1:2:4 (nominal mix) type B-2 (using 40mm graded crushed stone aggregates) as in surface channel and drains complete all as specified and directed.

RCC 1:2:4 ( nominal mix ) type B-1 (using 20 mm graded crushed stone aggregates ) as in slab and like complete all as specified and directed.

Extra for forming fair finished drain or channel n.exc 30 cm inner girth in cement concrete using extra cement including forms, moulds mitred / stopped ends etc complete all as specified and directed.

Use & waste of form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete, complete all as specified & directed.

Use & waste of form work to edges of concrete floor and roofs n. exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work n exc 10cm wide for rough finished surfaces of concrete, complete all as specified & directed.

Walling of random rubble stone masonry, uncoursed, well bonded, bedded and soilidly hearted built in CM 1:6, complete all as specified and directed.

All as per srl item no 24 above but except stone.

2nd class hardwood (Sal) plain solid straight chowkats and frames wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and directed.

Factory made solid PVC moulded door shutter 28mm - 30mm thick (stiles) with particle board core with 2,4,or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back ,supplying and fixing in frame at site complete all as specified and directed.

35mm thick second class hardwood (Sal/Hollock) factory made plain framed panelled shutter (two panel) with lock rails & panel of 9 mm B.W.P commercial ply wood or 12 mm thick veneered particle board with commercial veneering on both side. The size of rail and stile as per IS:1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

35 mm thick 2nd class hard wood (Sal/Hollock) glazed & skeleton factory made shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc, sizes of members of door shutters as specified in SSR- 2009 Part-I Section 8.24(a) complete all as specified and directed.

35 mm thick 2nd class hard wood (Sal/Hollock) glazed & skeleton factory made shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc, sizes of members of windows/ventilators shutters as specified in SSR- 2009 Part-I Section 8.24(b) complete all as specified and directed.

Aluminium handles cast type anodized of size 150 mm complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section of size 200 mm and fixed complete all as specified and directed.

Mild steel butt hinges of size 125mm medium weight cold rolled complete all as specified and directed.

250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

Mild steel ordinary rat tail rod pattern spring, 300mm including roller and roller plate complete complete all as specified and directed.

Hasp and staple, safety type, aluminium anodised with mild steel hinge pin size 100mm including bolt to hinge plate and fixed with screws complete all as specified and directed.

Brass handles 150mm polished bright complete all as specified and directed.

40mm Cupboard Knobs fixed with nut,screw and washer of brass polished complete all as specified and directed.

Galvanished mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanished wire staples complete all as specified and directed.

Sheet glass, 3 mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed.

Hi steel clip in false ceiling system with steel tile square or beveled edged (600mmx600mm) manufactured cut of 0.50mm thick polyster coil coated galvanized steel having 180 grams zinc coating. Coil coated steel tiles shall have 20 micron polyester coated finish on front side and back coat of 5 micron alkays primer. Two sides of each tile shall have raised and piped and stopped to ensure positive engagement in to the spring clip in profile allowing for demounting of individual tiles. The rigid suspension system consists to rows of 0.50mm galvanised steel clip in profile of size 38mm installed at 600mm centre to centre spacing to support the tiles. Wall suspension angles of size 24mmx24mm and 0.40mm thick are suspended from the roof structure by GI ceiling brackets. Wall suspension angle are made of coil coated steel matching the colour of the tile. They are jointed to the clip in-profile system by hold on clamps. The tiles/planks are held in place by pressure clips as per manufactures instructions for spacing. In the flexible system the hanger and butterfly clip replace the suspension angle. including necessary scaffolding all as per manufacturers specifications/instructions and specified and directed by Engr-in-charge/AGE(I).

10mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/ GI/ aluminium frame work fixed with nails, all as specified.

Extra for Non asbestos fibre cement board for external teak wood lipping complete all as specified and directed.

2nd class hard wood clean sawn timber, unframed and fixed as in scantling complete all as specified and directed.

Plain fillets of 2nd class soft wood (Kail), square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc 6 & not exc 13sq.cm, complete all as specified & directed.

40mm thick boarding in floors and skirting, hardwood 2nd class, planed one side & edges tongued and grooved or rebated with butt joints and fixed with screws complete all as specified and directed.

40mm thick boarding in floors and skirting, hardwood 2nd class, planed one side & edges tongued and grooved or rebated with butt joints and fixed with screws including repairs to existing floors in patches, including cutting out, piecing, heading joints etc complete all as specified and directed.

18/19mm block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work complete all as specified and directed.

0.63 mm thick CGI sheeting with nominal grade of zinc coating 275 gms per sqm with two corrugation side lap fixed with 'J' or 'L ' hooks as in roof covering,walls etc complete all as specified and directed.

0.63 mm thick plain, galvanised, mild steel sheeting as in ridges, hipe, valley gutters, drip and straight flashing (length and girth as fixed) with grade of zinc coating 275 gms per sqm complete all as specified and directed.

Rolled mild steel work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed.

Rolled mild steel framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in floor finish, surface finished even and fair to receive top finish complete all as specified and directed.

Plain cement concrete 1:3:6, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Chequered cement concrete coloured tiles, homogenious texture glossy finished , chemically coated machine pressed 30 cm x 30cm x 25mm thick set, jointed and pointed in near cement slurry in floor with gray cement and pigment and including 20 mm thick cement screed in cement mortar 1:4 over and including 75mm thick PCC 1:3:6 (nominal mix) type C-2 (using 40mm graded crushed stone aggregates) complete all as specified and directed. Shade/Colour of tile shall be approved by the GE.

Mat finish, premium quality, joint free (edge cut), coloured/ printed Non -Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

Glazed ceramic coloured tiles of size 450mm x 300 mm x 7mm / 350mm x 250 mm x 7mm thick as in skirting/vertical surfaces etc , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the GE.

20mm thick, Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. complete all as specified and directed.

Cutting, rubbing/grinding & mirror finish ,rounding of edges of marble/ kota stone/ granite stone complete all as specified and directed.

Rendering cement plaster 20mm thick in cement mortar 1:6 on stone masonry or surface other than fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 20mm thick in cement mortar 1:4 on stone masonry or surface other than fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Preparation of steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of old steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of old wooden surfaces of any description, over 10cm in width or girth,not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of old wooden ceiling surfaces of any description, over 10cm in width or girth,not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of wooden surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over and including 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

Preparation of old surfaces of wall by Complete removal of existing treatment and applying two coats of oil bound distemper over a coat of primer over and including 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

Preparation of new plastered surfaces or un plastered, previously undecorated wall surfaces and applying two coats of cement base paint, complete all as specified and directed.

Preparation of plastered or un-plastered, old surfaces of walls and applying two coats of cement base paint, complete all as specified and directed.

French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats of french polishing, complete all as specified and directed.

French polishing on old polished surfaces of any description, width or girth including cleaning and preparing the old surface with two or more coats of french polishing, complete all as specified and directed.

G I tubing medium grade of 15 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor/trenches complete all as specified and directed.

All as per ser item No 75 above but except pipe including new fittings as per requirement .

GI tubing medium grade of 20 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor /trenches complete all as specified and directed.

All as per ser item No 77 above but except pipe including new fittings as per requirement .

Cutting chases, pinning in. making good to facings here required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good complete all as specified.

Harrison rail (Curtain rail), mild steel, chromium plated with and including fixing brackets, stops, rollers etc. complete all as specified

Soap dish, SS, approximate size 160x 160x90mm, any type, fixed to plugs with chromium plated brass screws, fixed in repair complete all as specified.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Sink made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Wash basins, Vitreous China (Flat white type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete all as specified. Make: Cat Part No. 1008 of Cera or equivalent in makes mentioned in Appx

Stop valves/ angle valve/ concealed valve, cast copper alloy, chromium plated, fancy type, screwed down, high pressure , screwed both ends for 15mm bore iron pipe or for unions fixed in repair complete all as specified. Type of valve approved by the GE.

Stop valves cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 20mm bore iron pipe or for unions and fixed in repairs complete, all as specified.

Bib tap, cast copper alloy ,chromium plated, fancy type , screwed for iron pipe or for brass ferrule of 15 mm bore, fixed in repair complete all as specified and directed.

Chromium plated shower roses with or without swivel joints, 125mm size, including fixing to steel pipe or union complete all as specified

PVC connections 15 mm size with PTMT nuts of length 600mm fixed in repair complete all as specified and directed.

Brass chromium plated tubular towel rail 20 mm dia, "D" type, 60 cms long between flanges fixed in repairs with and including chromium plated brass brackets, brass screws complete all as specified

S&F in repairs, self cleaning water jet, chromium plated, Fancey Type high qualitey (HEALTHFUSET)15 mm bore ABC Body mild steel CP with 1.25 mtr ong flexible tube and ABS wall hook including making connections and fixied complete all as specified

Toilet papar holder Toilet paper holder Coloured, vitreous China, box type complete all as specified.

Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified.

Sensor type vitreous china urinal (including Sensor type flushing cistern ,Flush pipe, and waste pipe) , half stall type,white, PVC waste pipe including providing and fixing plugs,bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws,pointing around urinal back in cement mortar ,fixing flush pipe with grating and union complete fixed in repair all as specified and directed. .

S & F in repair Vitreous china urinal partion white of size 310 x 700mm and Urinal partions slabs terminating about 40cm above floor line complete all as specified

Vitreous China wash down water closet (pedestal pattern), white including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC white seat cover and chromium plated jet including PVC connection, fixed complete including demolition of old unservicable WC and provision of plain cement concrete M-15, type B-I, using 20mm graded crushed stone aggregate, fixed in repairs all as specified. Make: Cat Part No. 2008 for EWC, 2308 for seat cover, 2201/B for internal fittings of 'Cera' or equivalent makes mentioned in PS.

PVC valve less, crystal white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, all as specified. Make: Cat Part No. 2602 of Cera or equivalent in makes mentioned in Appx .

600x450 mm bevelled edge mirror of slected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screwed and cup washers.

PVC (SWR) 110mm bore (dia) soil, waste and ventilating pipe, singe socketed, in any length with Rubber Ring Joints fixed to walls, including taking down unserviceable pipe, fittings, etc, complete all as directed and all as specified.

PVC (SWR) 75mm bore (dia) soil, waste and ventilating pipe, singe socketed, in any length with Rubber Ring Joints fixed to walls, including taking down unserviceable pipe, fittings, etc, complete all as directed and all as specified.

PVC (SWR) 110mm bore (dia), Bends any type, with disminishing pieces or tapers and Jointing with Solvent Cement, complete all as specified and as directed.

PVC (SWR) 75mm bore (dia), Bends any type, with disminishing pieces or tapers and Jointing with Solvent Cement, complete all as specified and as directed.

Rotational moulded polyethylene water storage tank 1000 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete all as specified.

Taking down point wiring with aluminium/ copper conductor for light point, socket point/ power point etc. in PVC casing and caping, surface pvc/ steel conduits, wood batten with clips including taking down board any type and size complete with any type of switches, sockets, holders, (batten or pendent type), ceiling rose etc. The light fittings (any type), main switches, distribution board with MCB’s of any capacity and make are to be removed/ replaced if required and all as specified and directed. NOTE: - Existing fan regulator any type (Where required) and electric meters are to be refixed and connected properly where required.

Point wiring with copper conductor cable multistrand, PVC sheathed 1.5 Sqmm size(two run with colour code RYB) for one light point ,fan point, exhaust fan point,or bell point controlled by one switch including one run of 1.5 Sqmm (as continous earth wire Green)multistrand PVC concealed conduit of approved size and quality ISI marked,including all other required accessories as specified in preamable 1(a) to (q) of section 19 of SSR Part-II under heading 'point wiring' fixedon wall/ceiling including sunk cast iron terminal boxes grouting/flushing on wall for mounting fittings like switch,sockets etc covered with 3.00 mm thick plastic laminated sheet top cover of brick masonary/Stone masonary wall complete including cutting,chasing,pinning and making good the disturbed surface by using cement mortar 1:3 complete all as specified and directed by Engr-in-charge.,(Note:-the rate for concealed type point wiring shall deemed to include the cost of cutting,chasing in wall by using electric cutter and making good the disturbed surface of wall by providing cement plasterand matching the surface by white wash/colour wash all as per existing finishes complete).

All as per serial item No '105' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.

All as per serial item No '105' above, but for one 3 pin 5 Amps socket outlet, independent all as specified and directed.

All as per serial item No '105' above, but for one light point controlled by two way switch all as specified and directed.

All as per serial item No. '105' above but for 3 pin 15 Amps socket out let independent with 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Modular switch 1 way 6A, 1 module complete all as specified and directed.

Modular Socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.

Modular switch 1 way 16A,1 module complete all as specified and directed.

Modular Socket 6A/16A - 2/3 pin combined 2 module, complete all as specified and directed.

Modular white cover plate with frame, 3 module, complete all as specified and directed.

Modular white cover plate with frame, 4 module, complete all as specified and directed.

Modular white cover plate with frame, 6 module, complete all as specified and directed.

Modular metal flush box 3 module complete all as specified and directed.

Modular metal flush box 4 module complete all as specified and directed.

Modular metal flush box 6 module complete all as specified and directed.

Disconnection and taking down of fency/wall light fitting any type and securely placed at store and refixing on wall at existing/new places including all accessories and making good the disturbed surface complete all as specified and as directed.

Lamp holder, PVC/Polycarbonate type with back plate suitable for angular/ batten fittings including LED lamp, 10 watts complete all as specified & directed.

Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified.

LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Basic all purpose surface and wall mounted LED tube light fitting integral type 1 x 10W, 230V, connector block etc complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable tube light all as specified and directed. Havells Cat Part No LUMILINEPLUSBS10WLED865SPCS or equivalent in Bajaj/ CG/ Philips.

Basic all purpose surface and wall mounted LED tube light fitting integral type 1 x 20W, 230V, connector block etc complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable tube light all as specified and directed. Havells Cat Part No LUMILINEPLUSBS20WLED865SPCS or equivalent in Bajaj/ CG/ Philips.

S & F in repairs concealed sheet metal enclosure with socket plug top and MCBs having single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp 240V complete all as specified and as directed.

LED light fitting 1x 10W bulkhead luminaire including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

M & L for semi/complete flushing/grouting of existing factory made sheet metal enclosure dust and vermin proof made out of 2mm thick MS sheet of size 90cm x 90cm x 20cm depth with double door hinged shutter and locking arrangement for fixing DBs , KWH meteretc; complete all as directed Note:- The unit rateshall be inclusive of the making good the area not exceeding 2 sqm and not exceeding 0.125m depth for filling the hollow existing surface with half brick in CM(1:4) complete all as specified and as directed

MCCB, SPN, 125Amps, 240 Volts, 25 KA complete all as specified.

MCB SPN 32-40 Amp, 240 Volts, 10 KA all as specified.

MCB SP 6 to 32 Amp, 240 Volts, 10 KA all as specified.

Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 8 way, double door, 240 volts with 200 Amp rated bus bar completed all as specified.

Renewal of sheet metal enclosures for DBs when MCBs to be used, triple pole and neutral, 4 way, double door, 415 volts with 200 Amp rated bus bar including taking down ICDP/ DB's any type, kit kat fuse, MCB's any type, all as specified.

Renewal of sheet metal enclosures for DBs when MCBs to be used, triple pole and neutral, 12 way, double door, 415 volts with 200 Amp rated bus bar including taking down ICDP/ DB's any type, kit kat fuse, MCB's any type, all as specified.

LED 35 W, Energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP66 protection and Impact resistance of IK07 complete fixed on pole/ wall with and including bracket made out of galvanised iron pipe 40mm dia, medium grade of length 1.50 metres with two clamps made out of mild steel flat 25x4 mm with nuts, bolts and washers complete accesseries including two coats of aluminium paint after preparation of surfaces including making connection with aluminium PVC insulated copper wire 2.5 sqmm as required at site and connecting the same to the cable with the help of the connector all as specfied and directed . Make:- Havells Cat Part No LHETBXU7PAIS035 or equivalent in makes mentioned in PS.

Cutting/ grooving on plinth/ wall/ verandah in any condition for laying of cable through pipe and making good the disturbed surface by using cement concrete 1:2:4 type B-0, using 12.50graded crushed stone aggregate as required complete all as directed.

Taking down/ dismantling from pole/ wall/ floor/ trench XLPE/ service cable aluminium conductor of any size complete all as directed.

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in any type of soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm, complete all as specified and directed.

Removing excavated materials/ soils, not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed.

Sand cushioning to under ground cables provided with a layer of sand 8 cms thick before laying the cable and 15 cms thick after laying the cable complete all as specified and directed. Note: Punned thickness shall be measured.

Sub class "B" bricks for covering to cable laid dry flat, with width equal to length of bricks all as specified and directed.

GI pipe light grade of size 40 mm dia laid in trenches/ walls including clamps, screws etc, complete all as specified and directed.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 25 Sqmm, 4 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 6 Sqmm, 2 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed.

Removal of existing burnt winding of exhaust fans AC single phase230/240V of size 450mm sweep with louver by taking out from the wall frame, cleaning thoroughly with suitable cleaning agent, applying slot insulation and rewinding with new super enameled insulated 30 to 38 SWG copper wire of appropriate size including all winding, insulating material and impregnation of insulating varnish of any make, type, model, applying air drying the winding thoroughly complete, replacement of condenser of 3.5mfd with alonwith minor nut, bolts, lead wire, broken blade/MS frame and fixing to wall after paint and making good and fixed by anchor bolts and testing on completion, complete all as specified and directed.

Disconnecting/ taking down electric water heater for complete servicing and making funcitional, capacity 50 litre, removing and cleaning the dust properly, painting with two coats of synthetic enamel paint of same colour using spray gun after preparing surface for painting including refixing duly grouting nuts, bolts, washers and making plumbing connections and making the conections with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light and testing complete all as specified.

Renewal of sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded RLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 6 Sqmm and drawn into PVC conduit/ casing & capping with all fittings/ accessories, junction boxes 1 to 4 way 20mm dia, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and connected to common earth dolly including taking down old unservicable submain wiring, complete and as directed. Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor and one RM of earth wire of 6 Sqmm, shall be measured as one RM).

Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm, drilled and screwed including 3 nos. 8mm dia 25mm long hex head screw, complete all as specified.

Aluminum strip 25x3.15mm with saddles and fixing screws etc for roof conductors and down conductors above ground, complete all as specified.

Air termination single pointed aluminum rod 12mm dia and 300mm long, complete all as specified.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC (1:2:4), type B-I using 20mm graded crushed stone aggregates with 40mm thick precast cover of size 550 mm X 550 mm X 75 mm of RCC (1:2:4), type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6.3mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron strip 25mm x 4mm (as earth lead strip), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC M-15, type B-I using 20mm graded crushed stone aggregates with 40mm thick precast cover of size 550 mm X 550 mm X 75 mm of RCC M-15, type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

Deduct Credit Amount as per Schedule of credit as details given on Srl Page No 33 of tender doucments.

malghotra construction co

m/S Varun Gupta

Havish Construction

M/s Joginder Paul Bhatia

Substantial Const. Co.

M/S BISHAN DASS AND SONS

M/s Shakti Electric Works