NIT NO: 465/TC/2026-27

Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits. 1.1.1 ) In all types of soil

Extra for every additional lift of 1.5 m or part thereof. 1.6.1) In all types of soil 1.5 meter TO 3 meter

Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

Carriage by mechanical transport upto 5 km lead: 1.26.1) Earth

Supplying chlorpyriphos/ Lindane emulsifiable concentrate of 20% in sealed containers including delivery as specified.

Surface treatment by spreading emulsion under floor, over the plinth area before laying base concrete @ 5 litres / sqm.

Providing and fixing fometerwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: 2.1.1) Foundations, footings, base of columns and plinth beam in any shape and size.

Beams, lintels, cantilevers & walls

ii) Columns, rectangular or square in shape

Stair cases of all types excluding spiral and folded plate type, including risers and landings

ix) Suspended floors, roofs and balconies (plain surfaces)

Weather shade, chhajja, Cornices and mouldings

Extra for additional height every 1m or part thereof where height of staging for fometer work exceeds 4.0 metre with adequate bracing, propping etc at all levels, for suspended floor, roof, landing, beam and balcony. (only plan area is to be measured):

Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of fometer work. 3.3.2) M-25 (using minimum cement 410 kg/cum concrete)

Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: Ground Floor

Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluding cost of fometer work. 3.1.3) 1 cement :3 coursed sand : 6 gradedstone aggregate 40mm nominal size )

Applying a coat of hot bitumen VG-10 using @ 1.7kg/ sqm on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of fometer work. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size).

Providing and placing in position themetero-mechanically treated(TMT)steel reinforcement for RCC work including cutting, bending, binding etc. complete as per drawings including cost of binding wire and including all wastages etc. complete 3.12.2) Themetero-Mechanically treated bars FE 500D

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of WC, kitchen and the like consisting of: i) 1st course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound confometering to IS 2645 including rounding off junction of vertical and horizontal surface. ii) 2nd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound including rounding off junction of vertical and horizontal surface. iii) 3rd course of applying blown or residual bitumen applied hot @ 1.7 Kg. per sqm of area. iv) 4th course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg. per sqm of area.

Providing Water proofing treatment over Roof, Wall, Chhajjas, Balcony with Diamond Shield and Sealer coat or equivalent at leakage/ seepage area consisting of the operation: (i) Surface preparation roughening of surface, opening of cracks in ‘V’ groove in size of 5mm x 10m (WxD), filling of cracks with putty of Diamond shield with laying fiber glass mesh, Cleaning of surface by scrubbing with steel wire/ Nylon brush. Removing all dust particles and washing with adequate water to clean completely. (ii) Providing and applying 1st coat of diamond shield or equivalent compound (having two component dry powder 80% Chemical 20% (chemical having 30% solid contents) making flexible waterproof and protective modified mortar with minimum thickness 70-80 micron after proper mixing of both the parts of compound along with laying of fiber glass mesh (of weaving size of 10x10 yarn/inch duly coated with alkaline resistant polymer). Allow the coating to set in natural air for minimum 2 Hrs. After 1st coat apply 2nd coat with minimum thickness 100 micron of the same compound. Allow the 2nd coat to set in natural air for minimum 4 Hrs. Total consumption of the diamond shield or equivalent in both coat should be @ 17.90 kg for 10sqm area. (iii) Over the above layers providing and applying 1st coat of sealer compound (Single component High Build elastomeric, flexible, pure acrylic waterproofing membranes having solid content of 65%) minimum 50-60 micron and allow it to set in natural air for minimum 2 Hrs. After 1st coat apply 2nd and final coat 120-140 micron of sealer compound and allow it to set in natural air for minimum 4 Hrs. Consumption of Sealer compound should be @ 5.40 kg per 10 sqm area. The final area appearance of the coating will be milky white (iv) The treated area should be cure with water for 48 hrs by flooding the surface. All above operations to be done in order.The application shall be got done through the authorised applicator of the manufacturer.

Brick work with modular fly-ash lime bricks (FALG Bricks) confimetering to IS:12894-2002 of class designation 40 in foundation and plinth in: 7.5.4) Cement Mortar 1:6 (1 cement : 6 coarse sand)

Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: G.F.

Extra for brick work, where height of work exceeds 4.0 metre from immediate below floor level.

Extra for brick work curved on plan upto mean radius not exceeding 6 m including fometer work.

Half brick thick brick masonry with fly-ash lime bricks (FaLG Bricks) confimetering to IS:12894-2002 of class designation 4.0 in superstructure above plinth level upto plinth level: 7.11.2) Cement Mortar 1:4 (1 cement : 4 coarse sand)

Extra for half brick work in superstructure above plinth level for every story or part thereof in addition to rate for upto plinth level: G.F.

Extra for providing and placing in position hopping 25x1.60 mm or 2 no 6mm dia MS bars reinforcement at every third course of half brick masonry.

Providing and fixing in position doors, windows and ventilators frames made of cold rolled pressed steel sheet framed profiles made from commercial M.S. Sheets confometering to I.S. 513 of 1973 and as per general specifications of I.S 4351 including hinges jamb, lock jamb, steel butt hinges, base tie, joints mitred and welded with 10cm long legs of size 15x3mm M.S. flat, embedded in cement concrete blocks 15x10x10cm size of grade M-10 or rawl plugs and screws or with fixing clips or with bolts and nuts including neatly compacted filling M-10 cement concrete in profile section applying a priming coat of red oxide zinc chromate primer. 9.18.5) Double rebate 115mmx50mm size, 1.6mm thick sheet

Providing and fixing flush door shutters, confometering to IS 2202 (Part 1), interior grade, commercial type, core of block board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains, cross bands and face veneers on both faces of shutters excluding hinges. 8.13.1) 40 mm. thick (single leaf)

35 mm. thick (single leaf)

Extra for double leaf shutter instead of single leaf.

Providing and fixing stainless steel butt hinges IS : 12817 marked with necessary stainless steel screws etc complete. 100x2.5mm (heavy)

Providing and fixing stainless steel sliding door bolts with 16mm rod, 2.5mm thick flap, necessary stainless steel nuts bolts and screws etc complete. 8.137.1) 300 mm

Providing and fixing stainless steel tower bolts (Barrel type) with necessary stainless steel screws etc complete. 8.139.1) 250 x10mm

Providing and fixing stainless steel door handles having flap thickness 2.5mm, necessary stainless steel screws etc complete. 8.140.1) 150 mm

Providing and fixing stainless steel door latch with 12mm rod, 2.5mm thick flap, necessary stainless steel screws etc complete. 8.138.1) 300mm

Providing and fixing stainless steel hanging door stopper with necessary stainless steel screws complete. 8.143.2) Double

Providing and fixing stainless steel fixed stopper with necessary stainless steel screws complete. 8.144.3) 60 mm long

Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat of red oxide zinc chromate primer

Providing stainless steel railing/ grill made of S.S. flats, hollow S.S. pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and stainless steel bolts etc complete. 9.57.2) SS Grade 304

Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) confometering to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing and panelling to be paid for separately. 9.47.1) For fixed portion

For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately).

Extra for powder coated (minimum 50 micron) aluminium sections instead of anodized.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete. (Cost of aluminium snap beading shall be paid in basic item): 9.51.1) With float glass panes of 4 mm thickness

Providing and fixing stainless steel wire mesh of average width of aperture 1.56mm with wire of dia 0.45mm to doors, windows and clerestory windows including 19x12mm teak wood beading etc. complete.

Supplying and fixing rolling shutter of approved makes made of M.S. laths interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and out side locking with push and pull arrangement complete but excluding the cost of top cover and spring. 9.27.1) 80x1.25mm M.S. Laths

Providing and fixing 27.5cm long wire spring for rolling shutters.

Providing and fixing M.S. sheet top cover for rolling shutter 9.29.1) 1.25mm thick

Providing and fixing ball bearing for rolling shutters.

Providing and fixing mechanical device chain and crank operation for operating rolling shutters.

12mm thick cement plaster in cement mortar 1:5 (1cement:5sand)

15mm thick cement plaster on the rough side of single or half brick wall in cement mortar 1:5 (1cement:5sand)

6mm thick cement plaster In cement mortar 1:4

Neat cement punning

18 mm thick plain cement mortar band in cement mortar 1:4 (1 cement : 4 fine sand) per cm width: 11.32.1) Flush band

meter

meter

Add extra for plastering done on moulding cornices or architaves i/c neat finish to line& level

Providing and fixing chicken mesh weighting not less than 250 gms/ sqm as per IS : specification in the required width with 10mm long steel nails on vertical and horizontal surface near R.C.C. and brick walls junctions including scaffolding and all lead and lifts etc. complete before plastering upto 10mts in height.

Extra for plastering of exterior walls when height exceeds 10m above ground level for every additional height of 3.0m or part thereof.

Providing and laying ceramic glazed floor tiles confometering to IS : 15622 of approved size, make, colour, shade laid on 20 mm thick Cement Mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement mixed with matching pigment etc., complete. 12.9.2) Size above 300x300mm

Providing and fixing ceramic glazed wall tiles confometering to IS : 15622 of approved make, colours, shades and size on wall and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete. 12.7.2) Size above 200x300mm

15 mm thick Table rubbed polished Granite stone slab flooring laid over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing etc. complete. (Area of slab should be 0.50 sqm and above) 12.45.2) Granite stone black

15 mm thick Table rubbed polished Granite stone slab in risers and treads of steps skirting dado and pillars laid on 12mm (average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing etc. complete (single stone is to be used for risers and treads of steps and width of stone for skirting and dado shall be equal to the height of skirting & dado and length of 1.0 m). 12.46.2) Granite stone black

Granite stone lakha red/ shahi red

15mm thick Granite work (machine cut, table rubbed & mirror polished) for kitchen platfometer, vanity counters, window sills and similar locations of required size laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) including joints treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish. 13.6.1) Granite stone grey/pink

Extra for noing in Granite stone for treads.

Extra for providing edge moulding to 15mm thick stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 13.19.2) Granite work

Extra for making opening of required size & shape for wash basins/ kitchen sink in kitchen platfometer, vanity counters and similar location in marble/Granite/stone work including making necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

15mm thick Granite work (machine cut, table rubbed & mirror polished) for wall lining (veneer work) in cement mortar 1:3 (1 cement : 3 coarse sand) including pointing with cement mortar 1:2 (1 white cement: 2 marble dust) mixed with matching pigment. (Area of slab should be over 0.5 sqm). 13.4.3) Granite stone lakha red/ shahi red

Providing and laying vitrified floor tiles with double charge/ multi charge printing with water absorption less than 0.5% and confometering to IS : 15622 of approved make in all colours and shades and size mentioned below (+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete: Size 600x600mm

25 mm thick KOTA stone slab flooring over 20mm (average) thick base of cement mortar 1:4 laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding rubbing and polishing etc. complete (Area of slab to be over 0.20 sqm and upto 0.50 sqm)

KOTA stone slab 25mm thick in risers and treads of steps, skirting dado and pillar laid in 12mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. (single stone is to be used for riser and treads of steps and the width of stone for skirting and dado shall be equal to the height of skirting/ dado with a minimum length of 1.0 M.)

Chequered terrazzo tiles 22 mm thick with graded marble chips of size upto 6mm in floors on 25mm thick bed of cement mortar 1:6 (1 cement : 6 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles including grinding rubbing and polishing complete. 13.36.1) Light shade using white cement

Providing & laying 60mm thick precast interlocking concrete blocks of approved size (approx 305 sqcm) and shape/ pattern, over 40 mm thick average complete coarse sand bed with joints of 3mm thick filled by fine sand including leveling with surface vibrator, temping and sweeping etc. complete of minimum compressive strength of 250 kg/sq.cm 12.65.2) Pigment Coloured (rubber mould) precast interlock concrete blocks

Painting on new work (two or more coats) to give an even shade with: 14.22.1) Satin synthetic enamel paint (top most approved branded quality)

Wall painting with acrylic luxury emulsion (plastic) paint (top most approved branded quality) to give an even shade. 14.11.1) On new work (two or more coats)

Applying one coat of cement primer on wall surface.

Providing and applying 2mm thick ready mix exterior grade putty (Birla wall care, Alltek Superfine W/R of (NCL), J.K. wall putty) on walls to make the surface smooth and even.

Painting exterior surface with PREMIUM ACRYLIC SMOOTH exterior paint of required shade as per manufacturer's specifications to give protective and decorative finish including cleaning washing of surface etc. complete with: On new work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Providing and fixing on wall face UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness confometering to IS : 13592 (4kg/sqcm) including jointing with seal ring confometering to IS : 5382 leaving 10 mm gap for themeteral expansion. 18.76.2) 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes confometering to IS : 13592 (heavy) jointing with seal ring confometering to IS : 5382 leaving 10 mm gap for themeteral expansion. 18.77.1) Tee/ Tee with door/ Bend 45°/ Bend 90° 18.77.1.2) 110 mm

Access door cap 110 mm

Vent covel 110 mm

Nahani trap 110x75mm

"P" trap 110mmx110mm long

Providing and fixing UV stabilized Unplasticised - PVC pipe clips of approved design to Rigid PVC pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 18.78.2) 110 mm

Providing and fixing water closet squatting pan (Indian type W.C. pan), 100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (same colour) confometering to IS : 7231, with flush bend and other fittings and fixtures complete including cutting and making good the walls and floors wherever required : 18.1.3) White Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), confometering to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : 18.4.1) White pedestal type

Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required : 18.17.5) White Oval or round size 550x400mm.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 18.30.1) 5mm thick mirror

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and confometering to IS:8931 including C.P. brass extension if required: 19.14.3) Long body bib cock (500 grams)

Bib cock (400 grams)

Piller Cock (400 grams)

Stop cock (concealed) (600 grams)

Angle valve for basin mixer and geyser points (450 grams)

Bottle trap set with extension pipes

Toilet paper holder

Soap dish plate

Shower rose (revolving type) (150mm)

Towel rail (600mm long x 20mm dia)

Health foscet (hand jet) with flexible connection pipe (for WC)

CP brass water jet to be fixed in seat cover of WC with flexible connection pipe

Providing and fixing on wall surface G.I. pipes medium class complete with G.I. fittings and clamps, including cutting, making good the walls etc. and testing of joints complete: 19.7.3) 25mm nominal bore

32mm nominal bore

40mm nominal bore

50mm nominal bore

Providing and fixing concealed in wall G.I. pipes medium class complete with G.I. fittings and clamps, including painting with anti corrosive bitumastic paint, cutting chases, making good the walls etc. and testing of joints complete: 19.8.1) 15mm nominal bore

20mm nominal bore

Providing and laying in trenches G.I. pipes medium class complete with G.I. fittings including excavation of trenches, refilling the same and testing of joints complete: 19.9.6) 50 mm dia. nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 19.17.3) 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 19.16.1) 25mm

Providing and fixing gun metal non- return valve (horizontal type) of approved quality (screwed end) : 19.18.1) 25mm nominal bore

32mm nominal bore

Providing and fixing gun metal non- return valve (vertical type) of approved quality (screwed end) : 19.19.2) 32mm dia

40mm dia

Providing and fixing stainless steel drain jali of approved make/quality.

Making connection of G.I. distribution branch in G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: (dia of main line to be measured) 19.10.1) 25 mm nominal bore

32 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe (New work) including cutting and threading the pipe and making long screws etc. complete: 19.11.1) 15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal

40 mm nominal bore

50mm nominal bore

Providing and fixing white vitreous china urinal basin with waste fitting as per IS : 2556, and other couplings in C.P. brass complete: 18.13.1) Flat back half stall urinal of size 460x380x250mmFlat back half stall urinal of size 460x380x250mm

Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof.

Making chases upto 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality: 25mm nb

Providing and placing on terrace (at all levels) polyethylene water storage tank ISI marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing, lowering, laying, aligning, fixing in position at and jointing at all level/ depths ISI marked HDPE pipes of PE-100 grade and PN 6 for sewer application as per IS 14333-1996 (amended upto date) in trenches in complete including all material, labour, testing and commissioning as per direction of Engineer. Note : E/w to be measured and paid separately. 20.6.1) 100 mm dia

150 mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete 150mm thick as per standard design: 20.2.1) 100mm dia

150mm dia

Constructing brick masonry manhole with well burnt modular clay bricks crushing strength not less than 35kg/ cm² in cement mortar 1:4 ( 1 cement : 4 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation in cement concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : 20.7.1) Inside size 90x80cm and 45cm deep including CI cover with frame light duty, 455x610mm internal dimensions total weight of cover and frame to be not less than 38kg & weight of frame 15kg

Providing and constructing brick masonry chamber for . underground C.I. inspection chamber and bends with well burnt modular clay bricks crushing strength not less than 35kg/cm² in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C top slab with 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design. 20.28.1) Inside dimensions 455x610 mm and 45 cm deep for single pipe line :

2)Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :

Providing and constructing soak pit 1.20x1.20x1.20m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

Providing and fixing filter of minimum 100 litre capacity for roof top rain water harvesting through tube well consisting of two layered HDPE tank with five layers (each layers of minimum 100 mm) consist of coarse sand, 4mm, 6mm, 8mm & 12 mm gravels with stainless steel wire mesh fixed between each layer with suitable length and sufficient numbers of 110 mm dia PVC pipe pieces in the bottom of tank to support the above layer including fixing of inlet and out let P.V.C. pipe of required diameter upto 2 metre length on each side, Cement Concrete platefometer of required size complete as directed by Engineer in charge. (excluding cost of tubewell and inlet and outlet pipe beyond 2 metre)

Providing and fixing 80-100 mm dia PVC ball valve for inlet/ outlet of rain water harvesting pipe and filter.

Extra for precast PCC/ RCC work of any mix including fometer work, hoisting and fixing in Cement Mortar. 1:2 (1 Cement : 2 coarse sand) and finishing with cement plaster in Cement Mortar 1:3 (1 Cement : 3 coarse sand) but excluding reinforcement.

Designing, providing and fixing aluminium frame work made of special aluminium section on building face with M.S. angle iron brackets fixed on RCC structure with S.S. hold fasteners, including providing and fixing two sided structural adhesive tape of appropriate grade (NORTON or equilent), on aluminium sections for fixing aluminium/ glass panel, sealing on periphery of frame work, by providing EPDM gasket, silicon weather sealant between aluminium frame and building structure including hire charges of double scaffolding complete.

Providing and fixing aluminium composite panels in approved panel sizes, thickness and shape on aluminium frame work on face of building. (Frame to be paid for separately) 9.61.2) 4mm thick

Extra for cutting rebate in flush door shutter (total area of door shutter to be measured).

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down grade) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design.

Supplying and fixing C.I. cover without frame for manholes : 20.14.3) 560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg.

Providing and fixing aluminium strip 1.60 mm thick on expansion joints with iron screws as per design to match the colour, shade of wall treatment .

Providing and fixing in position impregnated fibre board confimetering to IS: 1838 in expansion joints, including cost of primer, sealing compound all complete. 3.21.2) 25mm thick

Providing and fixing one piece construction white vitreous china squatting plate urinal with an integral rim longitudinal flushing pipe, standard size G.I. flush pipe for back and front flush, C.P. brass coupling complete including cutting and making good the walls and floors etc. wherever required :

Supply and fixing of precoated TILE PATTERN profile sheets of approved make, colour, over all size, corrugation shape and pitch, having total coated thickness (TCT) 0.45 mm (approx weight 4.9 kg/sqm) with Zn-Al coating and superior paint and having yeild strength of 550 MPa. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymercoated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I.limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Supply, erection, jointing, testing & xommisioning of "C" Class MS pipes (as per IS:1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/angle irons including painting of metal part except pipe line. 23.1.5) 150 mm dia.

80 mm dia.

50 mm dia.

Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade includign surface preparation. 23.2.5) 150 mm dia.

80 mm dia.

50 mm dia.

Providing, installation, testing and commisioning of dual plate non return valve of folloeing sizes confimetering to IS:5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required. 23.4.1) 80 mm dia

Providing, installation, testing and commissioning of ci body buttefly valve os following to IS:5312 complete with rubber gasket, GI bolts, nuts, 23.5.1) 800 mm dia

Providing, fixing, testing and commissioning 250mm dia air vessele with required valves, pressure guages, drain system, constructed from ms pipe thickness should be min. 5mm

Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia and with necessary G.I. coupling, valve to be fitted on top of Air vessel of on wet riser as per specification.

Providing and fixing pressure switch with suitable for 1-10Kg/cm2 including 12/15 mm Ø isolation valve, G.I. nipple, elbow, electrical connection setting of Cut-in and cut-off pressure complete in all respects and in an approved manner.

Supplying and installing pressure gauge of 100 Ø ., 0-300 PSI or 0-21 kg per cm square fitted with 12/15 mm Ø . Pad cock valve, and G.I. pipe, elbow etc. as per requirement in approved manner.

Supplying and fixing swinging type First-Aid Hose Reel drum with Ms construction spray painted in post offece red colour, confometering to IS:884 with upto date amendments, complete with brackets for dixing on wall, connections from riser with 25mm dia MS/GI pipe and GM gate valve but excluding noe reel.

Supplying and fixing 19mm dia 30 metre long high pressure polypropylene First-Aid Hose Reel.

Supplying and fixing single headed internal hydrant valve with instantaneous Gun metal couplings of 63 mm ida with cast iron wheel ISI marked confometering to IS:5290 (Type -A) with blank Gunmeetal cap and chain as required.

Supplying and fixing single headed internal hydrant valve with instantaneous Gun metal couplings of 63 mm ida with cast iron wheel ISI marked confometering to IS:5290 (Type -A) with blank Gunmeetal cap and chain as required.

Supplying and fixing 63mm dia, 15 mtr long Flax canvas hose pipe with 63mm dia Male and Female Stainless Steel-IS:3444 Grade-I couplings duly binded with GI wire, rivets etc. confometering to IS:636 (Type-A) as required.

Supplying and fixing 63mm dia Stainless Steel IS:3444 Grade-1 branch pipe with 20 mm dia (nominal internal) Gun Metal nozzel confometering to IS:903, suitable for instantaneous coupling connection to connect hose pipe coupling as required.

Supplying and fixing of MS hose cabinet vox of made of 2mm thick MS sheet with front openable cover having 6 mm thick glazed glass viewing window i/c necessary locking arrangement, on existing wall/brick platfometer etc complete as required. Size 750mmX600mmX250mm

Supplying and fixing 4 way Fire Brigade Connection of cast iron body with 4 no.Gun metal male instantaneous intel couplings complete with cap and chain confometering to IS:904 including connection to existing MS pipe line complete as required.

Providing and fixing ms structural work fabricated from standard section.

Supply, erection, jointing, testing & commissioning of "C" Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/ angle irons including painting of metal part except pipe line. 23.1.4) 100mm dia.

80mm dia.

65mm dia.

50mm dia.

Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 23.2.4) 100mm dia.

80mm dia.

65mm dia.

50mm dia.

Supplying, fixing, testing and commissioning of flanged butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, confometering to IS: 13095 of following sizes as required. 23.5.2) 100mm dia.

80mm dia.

Providing and fixing 15 mm dia, Quartzoid bulb type G.M. Sprinkler Head set to operate at 680C of approved make chrome plated complete in all respect as required.

Providing and fixing M.S. structural work fabricated from standard sections, (MS rounds, angles, channels etc.) including cutting to size, drilling welding including cost of steel fasteners, clamp in RCC structural members as directed, including two coat of enamel painting over one coat of red oxide primer complete.

Wiring for light/ fan/ exhaust fan / call bell point with 1.5 sqmm FR PVC insulated stranded copper conductor single core cable in concealed PVC conduit, with 5 amp modular switch, modular base and cover plate, suitable size G.I. box and earthing the point with same size cable as required. Short Point

Medium Point

Long Point

Wiring for twin control light point with 1.5 sqmm FR PVC insulated stranded copper conductor single core cable in concealed PVC conduit, with 5 amp modular switch, modular base and cover plate, suitable size G.I. box and earthing the point with same size cable as required.

Extra for providing and fixing light plug point on board in concealed PVC conduit point wiring with modular type 3 pin 5 amp socket outlet and 5 amp switch including cost of base and cover plate and G. I. box etc. as required.

Wiring for light plug point with 2x2.5 sq mm FR PVC insulated stranded copper conductor cable in concealed PVC conduit along with modular type 6 Amp switch and 3 pin 6 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size cable etc. as required. Long Point

Extra Long Point I

Extra Long Point II

Extra Long Point III

Wiring for power plug point with 2x4 sq mm FR PVC insulated stranded copper conductor cable in concealed PVC conduit along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size cable etc. as required. Long Point

Extra Long Point I

Extra Long Point II

Extra Long Point III

Wiring for power plug point with 2x6 sq mm FR PVC insulated stranded copper conductor cable in concealed PVC conduit along with modular type 32 Amp SPMCB "C" curve and 6 pin 20 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size cable etc. as required. Extra Long Point I

Extra Long Point II

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in concealed PVC conduit as required. 3 X 1.5 sq. mm in 20mm conduit

3 X 2.5 sq. mm in 20mm conduit

6 X 2.5 sq. mm in 25mm conduit

9 X 2.5 sq. mm in 32mm conduit

12 X 2.5 sq. mm in 32mm conduit

3 X 6 sq. mm in 25mm conduit

Supplying and fixing of following sizes PVC conduit along with accessories in concealed complete as required. 3 X 10 sq. mm in 25mm conduit

3 X 16 sq. mm in 32mm conduit

4 X 25 sq. mm + 2 X 16 sq. mm in 50mm conduit

4 X 35 sq. mm + 2 X 16 sq. mm in 50mm conduit

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ concealed, steel/ PVC conduit/ PVC casing caping as required. 3 x 1.5 sq. mm

Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Fan regulator (two module size) electronic stepped type moving all rounds

Telephone socket outlet

Computer Outlet Jack

25/32 amp A.C. Starter switch

Ceiling rose 3 pin 5 amp

Batten/ angle holder

Providing and fixing composite unit for computer points having modular type 1 NO 6 pin 16 amp socket outlet, 1 NO 16 amp switch, 3 no 3 pin 6 amp socket outlets, 3 no 6 amp switches, suitable G.I. box, base and cover plates, earthing the sockets and switch box including etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts A.C. supply, complete as required. Deluxe

Providing and fixing round/ hexagonal fan box (125mm dia) depth 75mm (max.) with 12mm dia steel bar hook, 1.6mm thick MS sheet cover, in RCC slab etc. as required.

Supplying, installation, testing and commissioning of following sizes ceiling fan including wiring the down rods of standard length up to 30 cm with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable, earthing etc. complete as required. 1200 mm sweep

Supplying and fixing following sizes of down rod of 15/20mm dia M.S. pipe of thickness 1.6mm to ceiling fan including painting with matching colour etc. as required. 60 cm long

Providing and fixing pheNOlic laminated sheet cover of 180 mm dia 3 mm thick on the fan box etc. as required. (If provided at the time of installation of ceiling fan)

Supplying and fixing of wall/ cabin fan of 400mm sweep including connection etc. as required.

Supplying, installation, testing and commissioning of following sizes heavy duty (continuous running) 1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as required. 300 mm sweep

Supplying, installation, testing and commissioning of following sizes fancy exhaust fan having built in lovers in existing opening in wall including earthing etc. complete as required. 225 mm sweep

Supplying, installation, testing and commissioning of following surface/ concealed type fluorescent fitting (luminaries) complete with electronic ballast/ copper ballast glow type starter but without fluorescent lamp, on ceiling/ wall surface, earthing the fitting etc. as required. 4' x 40 W single box type

Supplying, fixing, testing and commissioning of following 230/250 volts fluorescent lamp (tube) in existing lighting luminaries as required. 4' x 36/40 watt

Supplying, installation, testing and commissioning of following LED fitting (luminaries) down lighters in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as required and furnishing 2 Yrs Guarantee certificate from manufacturer. 6 Watt

Supplying, installation, testing and commissioning of following sleek LED panel down lighters (luminaries) in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as required and furnishing 2 Yrs Guarantee certificate from manufacturer. 24 watt, size 300 x 300mm

36 watt, size 600 x 600mm

Supplying, installation, testing and commissioning of following 230/250 volts LED Post Top Lantern fitting with perplex cover, electronic driver, heat sink, capacitor and all other accessories on existing gate column/ pole bracket complete as required and furnishing 2 Yrs Guarantee certificate from manufacturer. 20 watt

Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 5 KV surge protection on pole bracket complete as required and furnishing 2 Yrs Guarantee certificate from manufacturer 90 watt

Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of NOt less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as required. (Only face area is to be measured) Upto 300 mm deep

Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of NOt less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as required. (Only face area is to be measured) Above 450 mm and upto 600 mm deep

Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) copper (electric grade) bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as required. 100 amp (20x3mm)

Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) copper (electric grade) bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as required. 400 amp (50x5mm)

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 3 pole MCCB, 100A, Adjustable Themetreal - Magnetic Release, 25KA

3 pole MCCB, 125A, Adjustable Themetreal - Magnetic Release, 25KA

4 pole MCCB, 400A, Adjustable Themetreal - Magnetic Release, 50KA

Supplying and fixing on surface/ recess vertical type following way, 415 volts, TPN MCB distribution board of sheet steel phosphatized and powder painted, with 200 amps tinned copper busbar, common neutral link, earth bar, din bar, detachable gland/ kNOck out plate, provision for 63/100 amp MCCB as incomer including interconnection between incomer MCCB and busbars, earthing etc. as required. (But without MCCB and MCB) (NOte : Vertical type MCB TPDB is NOmetreally used where 3 phase outlets are required.) 8 way (4 + 24), Double door with provision for 100 amps MCCB as incomer

12 way (4 + 36), Double door with provision for 100 amps MCCB as incomer

Supplying and fixing SP MCB, 240 volts, 'C' curve, suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as required. 6 amps to 32 amps

Supplying and fixing DP MCB, 240 volts, 'D' curve, suitable for inductive/ motor load in the existing MCB DB complete with connections, testing and commissioning etc. as required. 50 amps

Supplying and fixing TP MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Providing and fixing approved make, Manually Operated, draw out type, 415/500 volts, air circuit breaker complete with all standard accessories as per manufacturers specifications including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as required. 800 amps, 4 pole, 50 KA

Providing and fixing metal clad, 4 pole, on load change over switch unit (with sheet steel enclosure), 415/500 volts, in cubicle panel including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as required. (Connecting lead if required shall be paid separately) 800 amps

Providing and fixing metal clad, TP&N 4 pole automatic change over switch unit, 415/500 volts, including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as required. 400 amps

Providing and fixing following rating motor starter on metal board including, connections, testing and commissioning etc. as required. DOL three phase 32 amps

Providing and fixing 3 pole, 415/500 volts following rating (AC-1 Duty) power contactor in existing starter/ cubical panel including, connections, testing and commissioning etc. as required. 100 amps

Providing and fixing 4 pole, 415/500 volts following rating (AC-1 Duty) power contactor in existing starter/ cubical panel including, connections, testing and commissioning etc. as required. 400 amps

Providing and fixing following rating current transfometreer in existing cubical panel including, connections, testing and commissioning etc. as required. 100/5 amps

Providing and fixing following rating current transfometreer in existing cubical panel including, connections, testing and commissioning etc. as required. 400/5 amps

Providing and fixing single phasing preventer in existing panel including connection, testing and commissioning as required.

Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as required.

Providing and fixing penal mounting following rating digital type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as required. 0-100 amps

Providing and fixing penal mounting following rating digital type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as required. 0-500 amps

Providing and fixing penal mounting 0-500 volt voltmeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as required. Digital type

For ammeter

Providing and fixing following Time switch (timer) in existing panel including connection, testing and commissioning as required. AstroNOmical type with year programmed

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe, with charcoal and salt as required.

Supplying and laying 8 SWG copper wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ concealed conduit/ submain wiring/ cable as required.

Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth NOt less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 63 mm outer dia

Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth NOt less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 75 mm outer dia

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel ametreoured, aluminium conductor power cable of 1.1 KV grade direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. 3.5 x 35 sq. mm.

3.5 x 50 sq. mm.

3.5 x 120 sq. mm.

3.5 x 400 sq. mm.

4 x 10 sq. mm.

4 x 16 sq. mm.

4 x 25 sq. mm.

Supplying and making end temetreination with brass compression gland and aluminum lugs for following size ametreoured aluminum conductor power cable of 1.1 KV grade as required. 3½ X 35 sq. mm (28 mm)

3½ X 50 sq. mm (32 mm)

Supplying and making end temetreination with brass compression gland and aluminum lugs for following size ametreoured aluminum conductor power cable of 1.1 KV grade as required. 3½ X 120 sq. mm (45 mm)

4 X 10 sq. mm (22 mm)

4 X 16 sq. mm (22 mm)

4 X 25 sq. mm (25 mm)

Supplying, fixing and cramping suitable size and all type aluminium ferule/ lugs to following size 1.1 KV grade power cable core / lead, pressed with high pressure cramping tool including connection to switch gear/ MCCB etc as required. 10 sq. mm

Supply of hot dipped galvanized (in single dip to average 65 micron) octoganal pole made of 3mm thick steel sheet having window and flush cover with locking arrangement at suitable height from base for cable temetreination block, pole suitably reinforced with welded steel section at window cut section to make the strength of pole unaffected, with following minimum specifications including 3mm thick anchor plate, 4 no 20mm dia foundation bolts of EN8 grade. (designed for wind speed upto 150km/hr) 7 metre high, dia 130mm at bottom and 70mm at top, base plate size 220x220x12mm, foundation bolts 700mm long

Supply and fixing following street light pole bracket on existing pole made out of 50 mm dia MS "B" class pipe welded to 300 mm long MS pole caNOpy of suitable dia at a angle of 102.50 including having MS triangular stiffner of size 150 X 50 X 5 mm thick, making arrangement for tightening the bracket with pole by providing suitable size heavy duty nuts and bolts in caNOpy, painting with one coat of approved steel primer etc. as required. Single Over Hang 1.50 metre Long

Designing and providing suitable RCC foundation in Cement Concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm NOminal size) for 3 mere to 12 metre high GI octagonal pole including steel reinforcement (minimum 90kg per cum), fometre work, embeding 2 no 50mm dia PVC pipe for cable entry in each foundation, excavation disposal of surplus soil and curing etc. as required.

Painting of following height steel tubular poles with two coat of approved colour and shade synthetic enamel paint including cleaning the surface as required: Above 6 metre and upto 8 metre

Supplying, installation, testing and commissioning of submersible pump set for water supply system with submersible motor directly coupled to multi-stage submersible pump of specified discharge capacity, head, delivery size in existing bore well including 2 sets of suitable size holding clamps made out of 50 mm X 6 mm MS flat, connection with suitable submersible cable of standard length etc. as required. 3.0 HP, three phase

5.0 HP, three phase

Supplying and fixing following dia HDPE pipe PE-80 Grade (8kg/sqcm) in single length in the suction/ delivery line of water supply pump etc. as required. 50 mm outer dia

63 mm outer dia

Supply, installation, testing and commissioning of 1-3 HP 1 phase submersible motor starter cum control wall/ floor mounted type made out of NOt less than 1.6 mm thick MS sheet and comprising of following panel mounting switchgears there in including connection inter-connection etc. as required. a) Phase indicating lamps with fuses and toggle switches 1 set b) 1/2/3 HP 1 phase DOL starter with over load and NO volt relay 1 NO c) 25 A "C" curve DPMCB 1 NO d) Voltmeter 0-250 V 1 set e) Ammeter 0-10 A 1 set

Supplying and fixing 300 mm dia 2 mm thick M.S. sheet cover with 3 cm edge in two past on tube well bore pipe as required

Supplying, laying and fixing following size submersible cable along with GI/PVC/HDFC pipe line or laid in ground etc as required 3x4.0 sqmm

3x6.0 sqmm

Supplying and laying of approved make stainless steel wire rope of 6 mm dia for support of submersible pump set complete with tying to pump set and pump holding clamp.

Supplying of approved make split type Air Conditioner unit with cooling unit and condensing unit with standard length of upto 3 metre of copper piping with insulation etc complete as required: 1.5 ton split type capacity 4500 kcal / hr (3 star).

2.0 ton split type capacity 6000 kcal / hr (3 star).

Installation of split type Air Conditioner unit, cooling unit on wall inside and condensing unit on out side wall/ ceiling/ floor at desired locations with existing standard length of copper piping with insulation and power cable including providing and fixing necessary good quality powder coated MS frame etc complete as required. (Extra length of copper piping and power cable shall be paid extra on linear basis)

Supply, connecting and fixing extra length of copper piping for split type air conditioners of following dia and approved quality with insulation sleave etc complete as required 5/8 "

Supplying and fixing good quality powder coated MS frame for installation of out door unit of split type Air Conditioner at desired location with atleast 6 no steel fastners etc complete as required

Earth work in hard rock (without blasting) with all lead and 1.5 metre lift, dressing, stacking excavated strata including refilling with excavated soil in trench / pit to ground level complete as required

UOM Name

Percentage

Per mile

Siemens Per meter

Activity unit