Repair Maint of Auditorium Swimming Pool and other MES Installation OTM Accn and SPL Repair to UG Sumps at Ajmer Line and Provn of Water supply to pipe line Approx 525 Mtrs for perimeter GD Room of 156 LT AD Regt SP Under GE Army Utility in Army Area

Amount

Dismantiling of stone slabs and tiles (Kota stone etc.) of any description or any thickness in floors, aprons, skirting, dado etc. laid bedded and pointed in any mortar complete all as specified and directed.

Demolition of PCC Block of any description & in any position built in cement mortor including all quoins, arches, pillars etc. complete all as specified and directed.

Demolition of stone masonary of any description and in any position, built in cement mortar, including all quoins, arches and pillars etc. Complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping as specified

M&L for squared rubble walling Jodhpur type brought upto courses well bonded, bedded and solidly hearted built in cement mortar (1:6) complete all as specified and directed.

Extra over of hammer dressing to face stone with maximum depression on face from straight edge not exc 20mm and dressing face bed and joints as specified to squared rubble walling jodhpur type brought upto courses as directed

M&L for precast cement concrete block masonary with solid blocks of PCC (1:3:6) (using 20mm and 12.5 mm graded stone aggregate in the proportion as directed) exc 10cm in width and set and jointed in Cement Mortar (1:6) complete all as specified and directed.

Roughning sufaces of old concrete floor by picking , sweeping cleaning and washing down with water to remove dust etc.

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position , not otherwise specifically provided for as in roof treatment etc.complete all as specified and directed.

M&L for 75 mm thick PCC , (1:4:8) type D-2, (using 40mm graded stone aggregate) as in sub base for floor complete all as specified and directed.

M&L for Rubbersied Chequered cement concrete tiles 30 cmx30cmx22 to 25 mm thick, set jointed and pointed in neat cement slurry with grey cement and pigment, in floors, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

M&L vitrified ,coloured and printed tiles of size 600 mmx600 mm x 7 to 8 mm thick as in flooring over and including 15 mm thick cement screed in (1:6 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L vitrified ,coloured and printed tiles of width as directed and 7 to 8 mm thick as in skirting fixed over and including 10 mm thick cement screed in (1:4 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L non skid ceramic coloured tiles (300 x 300 mm) x 7mm thick in floors set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile including 10mm thick screed in cement mortor (1:6) complete all as specified and directed.

M&L for non skid ceramic tiles, joint free, coloured tiles 7mm to 8 mm thick (Square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile laid over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

M&L for Glazed ceramic tiles, joint free, coloured tiles 7mm to 8 mm thick (Square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in vertical faces i.e dado/skirting etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile laid over and including 10 mm thick screed bed or bedding layer of cement sand motar in( 1:4) complete all as specified and directed.

M&L for glazed ceramic tiles, coloured tiles, 247x122x8mm thick on floor etc set set & jointed with adhesive K2 unfix of Jai chemical industries limited or equivalent as approved by GE in swimming pool complete all as specified and directed.

M&L for glazed ceramic tiles, coloured tiles, 247x122x8mm thick on vertical faces ie. as in skirting/dado etc set set & jointed with adhesive K2 unfix of jai chemical industries limited or equivalent as approved by GE in swimming pool complete all as specified and directed.

M&L glazed ceramic coloured tiles (300 x 200 mm) x 7mm thick on vertical surfaces such as skirting, dados, & riser to steps, set & jointed in neat cement slurry & pointed in coloured cement to match the tile colour laid over and including 10 mm thick screed / rendering in CM (1:4) complete all as specified and directed.

Taking down existing wire mesh of any discription and in any position and supplying and fixing Stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm (weight not less than 600 gms/per sqm) and fixed with aluminium wire staples, wooden beads etc complete all as specified and directed

Supplying and fixing stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm (weight not less than 600 gms/per sqm) and fixed with aluminium wire staples, wooden beads etc complete all as specified and directed

Dismantling water tanks of any description in any position exceeding 250 & not exceeding 500 litre capacity complete all as specified and directed.

S&F Rotational moulded poly-ethylene 3 layer water storage tanks (cylinderical vertical with closed top) 500 litres capacity, white in colour hoisted and fixed in position with and including all fittings and fixtures complete all as specified and directed.

M & L for PVC ball valve, 20mm dia, high pressure with polythene float and fly nuts complete screwed/fixed to pipes/ferrules complete all as speified and directed.

S&F vitreous china squatting pan, Orissa pattern, size 580 x 440 mm white with integral foot rests and connection to trap and to flushing pipe, anti syphonege pipe etc complete including taking down existing WC and including making good the disturbed surfaces to match with existing surfaces complete all as specified and directed.

S&F as in repair Vitreous China, wash down water closet pan "Pedestal pattern" white including connection to drain and to flush pipe and anti syphonic pipe including all joints and making good the disturbed surfaces complete all as specified and as directed and as directed.

S&F in repair PVC valve-less, syphonic action type, flushing cistern, low level, 10 litre capacity white with inlet, ball valve, float and handle including brackets complete all as specified and directed.

M & L for Harrison rails, powder coated aluminum alloy of 25mm dia pipe decorative finish with and including supply and fixing powder coated decorated type brackets, stops, rollers etc. fixed on walls with brass screws with PVC rawl plugs as in curtain rods fixed as in repair complete all as specified and directed.

M&L for machine cut Kota stone slab 20 mm to 25 mm thick , as in flooring with border, laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to give granite finish, over and including screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:6 ) complete all as specified and directed.

M&L for machine cut kota stone slab 20-25 mm thick as in riser / steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick rendering in CM (1:4) complete all as specified and directed.

S & F vitreous china wash basin,white flat back , size 550mmx450mm with and including Waste fittings, brass, chromium plated for basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including Supplying and fixing cast copper alloy chromium plated, fancy type, pillar tap, 15mm bore, scrwed down high pressure with or without lettereed hot or cold with long shanks, screwed for iron pipe complete all as specified and directed as in repair.

S&F bib tap as in repair, cast copper alloy, screwed down high pressure with crutch of butter fly handle fancy type CP for 15 mm bore/dia GI tubing.

S&F Stop valves as in repair, cast copper alloy, screwed down high pressure for 15 mm bore/GI tubing pipe, high pressure, complete all as specified

S&F as in repair for Swivel shower rose of PTMT , any colour , for fixing with 15 mm dia pipe ,( minium weight 40 gm. ) with and including Shower arm 15 mm size, 195 mm long with bend of 45 degree with flange of PTMT any colour (Min wt 40gms) ,complete all as specified and directed .

S&F as in repair grating doom 100 mm dia of PTMT Min wt 25 grams etc all as specified.

Taking down existing chowkats or frames of any description and in any position exceeding 1.50 sqm but not exceeding 4 sqm each with shutter (w/o taking off shutter from the frames) complete all as specified and directed.

Taking down existing chowkats or frames of any description and in any position not exceeding 1.50 sqm each with shutter (w/o taking off shutter from the frames) complete all as specified and directed.

S&F 30 mm thick factory made Flush shutters , solid core construction , with block board core and plywood face panels commenrcialface on both sides with lipping/frame to match with and including preparation of the surfaces and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rai ; Panelling of plain colour PVC sheet 5 mm thickness to be fitted in MS frame welded/sealed to the style and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed.

S&F factory made solid panel PVC wire gauzed door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail with and including panels of stainless steel wire gauzed Supplying and fixing stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm (weight not less than 600 gms/per sqm) and fixed with aluminium wire staples, The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly complete all as specified and directed.

M&L mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces,etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S&F mild steel Butt hinges 100 mm, medium weight, cold rolled, mild steel complete all as specified and directed.

All as per item no 46 as above but 75 mm butt hinges -ditto-

S & F mild steel butt Hinges, medium weight, stainless steel,100 mm size complete all as specified.

S&F 200 mm long aluminium anodised , barrel tower bolt of extruded section and fixed all as specified and directed.

S&F aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

Hacking out old broken glass of any thickness and any description from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

S&F 3mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed.

S & F factory made steel windows with side hung glazed window including projecting type hinges with steel handles and steel peg stays , complete with glazing bars, dovetailed or welded and including mild steel grills/guard bars of approved design or pattern made of 12mm dia square bar including one shop coat of reoxide primer and applying two coats of synthetic enamel paint alround complete all as specified and directed.

S & F factory made steel windows with side hung glazed window including projecting type hinges with steel handles and steel peg stays , complete without glazing bars, dovetailed or welded including one shop coat of redoxide primer complete all as specified and directed with and including applying two coats of synthetic enamel paint alround complete all as specified and directed.

M&L for preparation of new steel surfaces and apply two coats of synthetic enamel paint over a coat of red oxide primer over 10 cm in width or girth of surfaces complete all as specified and directed.

Taking down cement plaster of any description and in any position of stone/ brick/concrete surfaces on walls/celing etc. including racking out joints, hacking for key, scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:4) on fair faces of brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers ie. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) and top layer mixed with water proofing compound as per manufacturer's instruction & finished even and smooth without using extra cement all as specified and directed. (Note:- Water proofing compound shall be measured and paid seperately under appropriate item of BOQ as "supply only")

Supply only water proofing compound all as specified and directed.

M&L for preparation of the newly plastered surfaces of walls & applying two coats of oil bound distemper over a coat of white wash on wall surfaces complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

M&L for applying two coats of cement base paint over a coat of cement primer on walls including preparation of newly plastered surface complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size 75mm to 110mm of any pattern) ,of any description and in any position, including all fittings , heads, shoes, bends, swan necks, etc., (measured overall as fixed along the centre line over fittings and accessories)complete all as specified.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed on walls complete all as specified and directed

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed on walls complete all as specified and directed

S&F PVC (SWR) bends, 110 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends, 75 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) Junction, single, (single T) equal or unequal with access door, 75 mm bore, complete all as specified and directed.

S&F PVC (SWR) Junction, single, (single T) equal or unequal with access door, 110 mm bore, complete all as specified and directed.

S&F for PVC (SWR) vent cowl, 110 mm bore complete all as specified and directed.

S&F for PVC (SWR) vent cowl, 75 mm bore complete all as specified and directed.

Taking up or down steel tubing and connection of 15 mm bore tube of any description & in any position complete all as specified and directed.

All as per item no 73 as above but 20 mm bore tubing.-ditto-

Supply and fixing unplastisized CPVC pipe, 15mm dia (nominal) of pressure rating 10 per centimeter square complete with fittings and fixed to walls/ ceiling/floors etc in required length complete all as specified and directed

Supply and fixing unplastisized CPVC pipe, 20mm dia (nominal) of pressure rating 10 per centimeter square complete with fittings and fixed to walls/ ceiling/floors etc in required length complete all as specified and directed

Taking out and removing old existing hinges of any discription and in any position from steel windows/ventilators from any location (Ground floor/1st floor etc) and supplying and fixing 50 mm size, box type heavy weight, mild steel hinge in position with spot welding and screwing as required and making good the disturb surfaces of window/ventilators to match with existing finish/painted surfaces all as specified and directed by Engineer -in-charge.

S&F as in repair Granite slab 20mm thick machine cut, bedded and joined with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing type as in cill and jamb/skirting, steps including rounding off the exposed edges all as specified and directed..

S&F stainless steel health faucet with 1 Mtr tube and hoock complete all as specified and directed ny Engr-in-charge. Confirming to Cat part No BEA- 41 of prayag /jaguar/HINDWARE/CERA completed all as specified

S&F as in sepair 60 mm thick, machine made ,1st quality, precast cement concrete rubber moulded coloured interlocking paver blocks / tiles , of triangular / Zigzag / Haxagone/ I , in shape or shap and designe as approved, with grey cement and pigment , having crushing strength not less than 300 Kg / Sqcm and conforming to IS specifications , laid over and including a layer of 25 mm thick sand cushion including filling the joints with sand , as in floors/ paths/ pavings etc, complete all as specified and directed.

Preparation of old decorated surface of wall and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and M&L applying one coat of white wash , complete all as specified and directed. by Engr-in-Charge

Preparation of old decorated surface of ceiling and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and applying one coat of white wash complete all as specified and directed.by Engr-in-Charge

Preparation of old decorated surface of wall and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and M&L for applying one coat of cement base paint including watering and curing of surface adeqautely before and after application of cement base paint complete all as specified and directed.

Preparation of old decorated plastered or unplastered surfaces of wall including washing , rubbing down and stopping of distempered surface M&L for applying one coat of distemper oil emulsion paint white or tinted complete all as specified

Complete removal of existing treatment on wall (any number of layers ) by scarping with steel scapers or any other mean including filling depessions of scapped surface with putty and pereparation of surface for further treatment and M&L for two coats of distemper oil emlusion white or tinted over two coat of wall care putty (Birla white) on walls complete all as specified and dircted by Engr-in -Charge

Preparation of old painted surface of wood and wood based material any description and in any position over 10 cm width or girth and M&L for applying one coat of synthetic enamel paint all as specified and directed by Engr-in-Charge.

Preparation of old painted surface of steel and iron surface of any description and in any position over 10 cm width or girth and M&L for applying one coat of synthetic enamel paint all as specified and directed by Engr-in-Charge.

Complete removal of exiting treatment from external wall preparation of old plastered surface and applying two coat of premium acrylic exterior anti algal fungal emulsion paint on wall all as direced by Engr-in-Charge.

Preparing of old painted concrete surfaces (Chequred Tiles) or plaster surface of any description and in any postion over 10 cm width or girth and M&L for applying one coat of Exterior Emulsion (Weather coat) complete all as directed by Engineer in Charge.

Demolition of Reinforced Cement concrete of any description and in any position not otherwise specially provided including revomoving debris to a place exe. 1.5km and n. exe. 5km outside MD land as directed

M&L for Use and waste Formwork to chajjas including edges for rough finished surfaces of concrete complete all as specified and directed

M&L for reinforced cement concrete (1:2:4) type B-1 ( using 20 mm graded stone aggregate ) as in beams , cantilevers bressummers , lintel over 1.5 m span etc. complete all as specified and directed.

M&L for reinforced cement concrete (1:2:4) type B-1 ( using 20 mm graded stone aggregate ) as in Chajjas complete all as specified and directed.

M&L for mild steel TMT bars ,10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars 5 mm and over upto and including 10 mm dia , as in stirrups , spacers , and binders , cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Taking down shutters of any description exc 1 sq. m and n exc 2 sq. m each.

Dismantling of RCC posts or struts of any section incl. taking out embedded portion and making good of disturbed ground (posts embedded in natural ground) etc complete all as specified.

All as per item No 98 here-in-before but posts embedded in concrete.

Dismantling chain link fencing of any type fixed in any situation including flat iron MS round bars, mounted on nuts & bolts etc complete all as specified.

Excavating in posts holes (or similar holes) in any type of soil each n.exc 0.50 cu.m getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm. Complete all as specified.

M&L for providing PCC 1:3:6 type C2 using (40mm graded stone aggregate) in foundation filling and mass concrete.

S & F Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work. Complete all as specified and directed.

Supply only, chain link fencing of MS galvanized fencing, any size or type.

Fixing only chain link fencing including line wires, any mesh , size and type fixed to any type of standards, rails, straining bolts, etc., incliding provision of binding wire complete all as specified and directed Note : Supply only chain link fencing and line wire will be measeured and paid separetly.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed to other, or screwed both ends, each screwed end to be fitted with washers and hexagonal or square nut length of bolt exc 10cm but n.exc 20cm long and dia of neck 11 to 15mm.

M&L Mild steel round bars, 10mm dia cut to length weared and securing chain link fencing to fencing posts, complete all as specified and as directed

S&F galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts including, securing and tying at crossings with and provisions of galvanised mild steel wire staples or steel pins etc as directed (each line wire to be measured).

M & L Providing precast cement concrete louvres and jallies, 40mm thick (measured solid) Type B0 (1:2:4 12.5mm graded aggregate set in CM 1:6, including all mouldings but excluding frame complete all as specified and directed

Dismantling plain or corrugated steel sheeting, any guage of any description and in any position as in roof coverings including connected ridge complete all as specified and directed.

M&L for PCC (1:3:6) type C2, (using 20mm graded stone aggregate) as in plinth protection, 50 mm thick, finishing the surface even and smooth w/o using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and directed.

S & F factory made steel vetilator with top hung glazed shutters, including projecting type hinges, with steel handles and steel peg stays , complete with glazing bars, dovetailed or welded and including mild steel grills/guard bars of existing design or pattern made of 12mm square bar as directed by Engr-in-Charge including one shop coat of redoxide primer. Complete all as specified.

S&F factory made steel ventilator with top hung glazed ventilator including projecting type hinges with steel handle and steel peg stay complete as per exiosting design pattern without glazing bar , dovetailed or welded and including one shop coat of redoxide complete all as specified.

S & F in repairs mild steel pressed handles left / right for steel window 125mm long including nut bolt and washer. Complete all as directed.

S & F in repairs mild steel pressed handles left / right for steel window 125mm long including nut bolt and washer. Complete all as directed.

S&F MS work in roof trusses (framed), trussed, rials and fastenings and heavy bracket. Framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc with Fe 410.0 or Fe-310.0 complete all as speciafied and directed.

Roughening of the existing surface of concrete including removing/demolition of loose/damaged cement concrete (unreinforecd) of any descrition and in any position not otherwiese specifically provided for with removing existing treatment(tarfelt)including removing of rubbish to t distance exc 250m but not exc 500m complete all as specified and directed.

Disconnecting existing tanks of any description & in any position any capacity settingaside(or lowering if required) for repairs, cleaning with detergent/detergent powder and finally disinfecte weith bleach wash etc, and hoisting, if rquired, reconnecting and re fixing in position including cleaning and removing all scale dirt etc. from tanks and from mouth of circulating pipes etc. and writing the date of cleaning and due date for cleaning of tank capacity of tanks exc 250 ltr and not exc 500 liter complete all as specified and as directed.

M & L for roof treatment with 3 mm thick APP modified water proffing membrane with 100mm overlaps sealed and bounded to the surface including finishing by applying aluminium paint @ 100 gram/sqm on roof or vertical surface complete all as specified and directed > (MAKE : SUPER THERMOLAY manufactured by M/s STP limited or MOPLY-FP manufactured by M/S Texsa India ltd or IWL (HYPERPLAS POLYSTER) manufactured by M/s IWL/Shivam TAR Products.

M & L Providing, cement concrete 1:2:4 type BO (using 12.5 mm stone aggregate) as in PCC padding to level the damaged roof surfaces and finishing the surface even and smmoth to required slope and gradient all as specified and directed.

M&L 25mm thick cement concrete 1:2:4 type BO using 12.5 mm stone aggregate in floor with using water proofing power(water proofing power paid seprately)

Applying evenly a tack coat of industrial Bitumen 85/25 at the rate of 1.5 kg per Sqm includingcleaning surface in sunken portion all as directed by Engineer in charge

S&F for swimming pool chromium plated Bib taps , fancy type long body with flange for 15mm dia bore GI Pipe or for brass ferrule and fixed in repair complete all as specified .Make Jaquar QQT-7037/ or eqvivalent of ROCA /Hindware/PARYAG.

S&F in auditorium chromium plated Bib taps , fancy type long body with flange for 15mm dia/ bore GI Pipe or for brass ferrule and fixed in repair complete all as specified .Make Jaquar code CON 47 KN ROCA /Hindware/PARYAG

S&F in repair Pillar taps, cast copper alloy , with capstan heads, chromium plated , Fancy type screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified .Make Jaquar code CON 127BKN/ROCA /Hindware/PRAYAG

S&F Stop valves, cast copper alloy, ISI marked ,concealed type chromium plated,with long shank and cup, screwed both ends for iron pipes or for union,for 15 mm bore,fixed in repair,complete all as specified and directed. Make Jaquar code CON 807 KN ROCA Hindware/PRAYAG

S&F in repair 10mm thick plain edge moulded cornor glass shelf fix with bracket of 300 mm wide all as specified and directed by Engr in charge

S&F tubular towel rail of brass chromium plated , 20 mm dia, D type, 60 cm long betweem flanges complete all as specified and directed.Make Jaquar code CAN/ 1111NM/ROCA /Hindware/PRAYAG

S&F in repair adjustable type concrete floor inlet nozzle made of white ABS plastic along with required fitted and jointed to main 350 mm dia UPVC pipe inside swimming pool wuth resin bonded fibre reinforced plastic as per manufacture instructions and as per directed by Engineer in charge . Nozel shall be as per item code No 00303 of make - Astral pool or eqvivalent as approved by GE , Nozel fitted in pool shall be tested for pressure & leakage for minimum 24 hours at pressure 6 Kg /Sqcm .

S&F as in sepair Powder coated (minimum thickness of powder coating 50 micron ) aluminium frame for doors , windows(Three track) , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified by Engr. In Charge. Note: thickness of powder coating should not be less than 50 micron.

M&L as in sepair for powder coated (minimum thickness of powder coating 50 micron ) three track Aluminium sliding window weighing 0.55 kg / m including h rubber packing / aluminium hardware complete all as specified and directed by Engineer-in-Charge Note :- Glass & Wiremesh should be measured and paid seprately

S&F as in repair powder coated anodised aluminium door shutters,aluminium section weighing0.55kg/m including necessary joining cleats,glazing clips,ruber neoprene packing, handles 2nos in each door,hinges anodised aluminium snap beading screws etc.complete all as directed by Engineer in charge.

S&F hydraulic door closer aluminum body fixed in repair design No 3 universal type, suitable for door shutter all as specified and approved sample

S&F powder coated aluminium grill of design No DG-104 7.5mm thick of decogrill or equivelent approved make with 1 mm thick 'F' sections of suitable size all as directed by Engg in Charge.

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof and wall complete all as specified and directed.

SPECIAL REPAIR TO UG SUMPS AT AJMER LINE (138 TO 145) Dewatering of existing water tank and cleaning the inside surfaces of the tank by scraping down walls & bottom surface using steel wire brushes to remove all disputation / fungus, other micro- organisms etc. . using light hammer & wire brushes, taking out and removing sediment loose dirt/ mud sludge, vegetation and other foreign materials completely from the tank disposal of all the waste / spoil to out of MD land at a place as specified by local bodies and washing repeatedly the inside surfaces of tank with water and washing with rebukes solution and clean water thoroughly all as directed by Engr-in- charge.

Dismantling / taking down old existing unserviceable cement plaster, loose / unsound weaken cement concrete of any description and in any position from existing external / internal surfaces of RCC OHT/sump/ wall / roof / beams / columns / RCC , average depth 25mm (at any staging) with power driven of pneumatic chisel and disposal of unservicable material debris and rubbish outside MD land at a place as specified by local bodies including cutting of all edges, making square shoulders of the cavities, roughening the smooth surfaces, scrapping out / removing corrosion all loose / scale / rust etc from the visible reinforcement by applying rust remover Reebaklens RR (3-4 Sqm per litre) equivalent of Chemco system/Webac chemicals and cleaning the steel reinforcement properly and then applying single component cementitious corrosion inhibiting primer for steel reinforcement two coat of two component Zinc rich epoxy anticorrosive primer of Nictozinc primer (4-5 Sqm per litre) or equivalent of Chemco system/Webac chemicals on visible reiforcement surfaces to form a contineous dry film not less than 80 micron thick all as specified and directed by Engineer in charge.

Applying Protective coating to inside of Tank- Providing and applying, the high – build, water based epoxy coating Nitocoat EP 405, two-component, water dispersed epoxy formulation. The product shall be of high-solids, not less then 100% by volume. The product shall be applied at 200 microns dry film thickness in two coats.The product shall exhibit adhesive bond strength to concrete of 1.0 Mpa minimum, when tested to ASTM D4541 test method etc complete as per FOSROC specification and as per the directions of the Engineer in charge.

M & L for providing and fixing welded MS wire mesh weighing not less than 1.5 kg/sqmt and applying - Mucis protezion Ferro mono primer (single component, comentitious corrosion inhibiting primer) of make Thermax Ltd or FOSROC equivalent of webac chemicals / chemco system on exposed steel reinforcement and wire mech having Mixed density of 2.01.2.05, Adhesive bond strength - 1 N/mm2 touch drying time of 10-15 minutes at 35 Degree Celcius and recoatable time 30 minutes and applying 25mm thick cement mortar with guniting machine/shotgun pressure not less than 5 kg per sqm in the ratio of 1:4 mixed with liquid water proofing admixture (Warep of make Thermax Ltd or equivalent of webac chemicals/chemco system 100/L Confirms to IS 2645-2003, having specific gravity 1.1-1.2 gm/cc, chloride content : Nil as per IS 2645-2003 & TM Bond ACB having specific gravity of 1.02) of thermax limited or equivalent of webac chemicals /chemco system in ratio s per recommendation of manufacturer, total chemical not less than 5% by weight of cement complete all as specified and directed by Engineer in Charge.

M & L rendering 20mm thick of cement mortar using (Single component thixotropic fibre reinforced polymer modified repair mortar) of Fosroc/equivalent to achieve Compressive strength of 15 N/mm2 in 1 Day, 25 N/mm2 in 3 Days, adhesion bond strength of >2N/mm2, furnished the surface even and smooth all as specified and directed by Engineer in Charge.

S&F CI bends of 100 mm bore of pipe any radius or tapers all as directed.

M&L for prepration of old painted steel surface and applying two coats of synthetic enamel paint

M & L for plain cement concrete (1:2:4), type -B1 (using 20 mm graded stone aggregate) as in flooring, 40 mm thick finished even and smooth without using extra cement complete all as specified and directed.

PROVN OF WATER SUPPLY TO PIPE LINE FOR PERIMETER G.D ROOM OF 156 LT AD REGT (SP) JOB NO : JODH/MW/29/20-21 (146 TO 157) Excavation in trenches not exc 1.5m width and n exc 1.5m in depth and getting out for laying of pipes etc in any type of soil, all as directed.

Returing filling in incl spreading levelling watering and well ramming in layers n exc 25cm in any type of soil all as directed

Removing excavated material n exc 50m and deposting where directed at a level n. Exc 1.5m above starting point all as directed

S&F High density polyethylene pipes (HDPE) of pressure rating 6kg/cm2 fixed complete to walls, ceiling or in floors, stable for hot & cold water supply with fittings of size 40mm dia. Complete all as directed by Engr-in-Charge.

S&F High density polyethylene pipes (HDPE) OF PRESSURE RATING 6 kg/cm2 fixed complete to trenches walls, ceilling or in floors and excavation, stable for hot & cold water supply with fittings of size 32 mm dia laid in trenches/all as directed by Engr-in-Charge.

Supply and laying GI tube Medium Grade complete including fittings of size 25 mm dia.

Supply and laying GI tube Medium Grade complete including fittings of size 20 mm dia.

S & PP-R ball ball valve (brass insert) of size 40mm dia as per requirement of the site and as directed by Engineer in Charge.

Stop valve cast copper alloy screwed down highpressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed or size 20mm bore pipe.

M & L for construction of valve chamber with PCC FOUNDATION 1:4:8 type D2 using 40mm grade stone aggreagate, stone masonry built-in cement mortor 1:6, cement plastering in CM 1:4, 10mm thick internally and 15mm thickness externally above and below ground level, cooping with PCC 1:2:4 type B1 using 20mm graded stone aggreagate, including frame made of angle iron of size 40X40X5mm to match with the internal size of the valve chamber and chamber cover made of solid PVC sheet 15mm thick, painting the surfaces with the two coasts of synthetic enamel paint over a coat of red oxide primer to steel surface including necessary earth work, excavation etc all as specified and directed by Engr-in-Charge

S & F self priming 1HP monoblock pump set, single phase rated voltage 220V, 50HZ, (impeller material-brass, copper winding, suction/delivery pipe size 25/25)

M & L Cutting of existing GI/DI pipe line for insertion of TEES, UNION, taking branch connection of size upto 80mm including all fittings & accessories required for connection, all as directed by Engineer -in-charge.

ELECTRIFICATION WORKS Taking down carefully point wiring from existing place (light/fan, socket or power points complete) with all fittings such as switches, sockets ceiling rose , pendant holder, fitting and fixtures , MCB DB’s , MCB, Main switches, call bell etc and making good to disturbed surface to wall ,floor etc to match with existing surface either by using same colour distemper or white colour wash all as required and directed by the Engr-in-Charge.

Taking down care fully by unscrewing from boards /out let boxes ,fittings and fixtures such as Tube light fitting /of any type / /MCB DB etc . Note : - This item to be operated only when item found serviceable for re –use in work.

M&L for point wiring PVC FRLS insulated and unsheathed multi stranded copper conductor cable of size 1.5 Sq mm , 1100 V drawn in and including PVC casing and capping complete including cast iron/pressed steel terminal box 1.6 mm thick of required size and Bakelite sheet 3mm thick for mounting switch , socket brass screws and washer including PVC insulated and unsheathed multi stranded copper wire of size 1.5 Sq mm as continuous earth wire for the following :- (a) One light /fan point controlled by one, one way switch

(b) One 5/6 Amp socket on the same board with other switch

(c) One 5/6 Amp socket on independent board.

(d) All as per item No 1 but for One 3 pin 15 Amp socket independent with 2.5 q mm PVC insulated unsheathed multi stranded copper conductor and earth wire with 1.5 Sqmm

(e) One bell point controlled by one, one way bell push button.

All as per item No. 160 Above but concealed drawn in and including non metallic PVC conduit 20mm medium grade for the following :- (a) One light fan point controlled by one way switch.

(b) One 3 pin 5 Amp socket on the same board

(c) One 3 pin 5 Amp socket on independent board.

(d) One 3pin 15 Amp socket independent but with 2.5 sq mm PVC insulated unsheathed multi stranded copper conductor and 1.5 Sq mm size PVC insulated soild copper conductor as earth continuity conductor.

(e) One bell point controlled by one push bottom switch.

Fixing only any type of Tube light fitting obtained from Item No. 159 Above Including making connection to ceiling rose /connector with copper flexible cable of size 1.5 sq mm all as specified and directed

S & F in replacement switch piano type 240 V, 5 Amp , SP one way flush type complete all as specified

S & F in replacement bell push 240 V, 5 Amp , SP one way flush type complete all as specified

S&F in replacement of sheet metal enclosure for MCB DB TPN double door, 4 way 200 Amps rated Bus bar complete all as specified and directed.

S & F in replacement of existing points socket outlet 5 pin 5 Amps flush type.

S&F in replacement of switch socket outlet combination 3 pin 15 Amp, 3 Pin 5 Amp out let flush type (non shuttered) for existing points complete all as specified.

S&F in replacement ceiling rose surface backelite, 65 x 20 mm three terminal complete all as specified and directed.

S&F in replacement of lamp holder PVC cased body with back plate complete.

S & F in replacement of modular switch 1 way 6 Amp, 1 module, 240 V flush type complete all as specified

S & F in replacement of modular switch 1 way 16 Amp, 1 module, 240 V flush type complete all as specified

S & F in replacement of modular bell push, flush type, 6 Amp, 1 module, 240 V complete all as specified

S & F in replacement of modular socket, 6A-2/3 pin combined, 2 module, 240 V complete all as specified

S & F in replacement of modular socket, 6Amp / 16Amp-2/3 pin combined, 2 module, 240 V complete all as specified

S & F in replacement of modular fan step regulator, 120 W, 2 module, 240 V complete all as specified

S & F in replacement of modular white cover plate with frame, 3 module, complete all as specified

S & F in replacement of modular white cover plate with frame, 4 module, complete all as specified

S & F in replacement of modular white cover plate with frame, 6 module, complete all as specified

S & F in replacement of modular white cover plate with frame, 8 module, complete all as specified

S&F as in replacement sheet metal enclosures for MCB distribution board SPN 8 way double door type with 200 amp rated bus bar and suitable for SPN Isolator as incomer complete all as specified

All as per item No. 180 here-in-before but SPN 4 way 240 Volt.

S&F Isolator TPN , 63 Amp 4 pole Isolator, 415 Volt complete all as specified in existing DB,S as in replacement .

S&F in replacement Isolator SPN , 63 Amp , 240 Volt complete

S&F in replacement MCB SP upto 40 Amp ,240 Volt complete

M&L for replacement of bell electric , 240 Volt , single pole complete

M&L for replacement of regulator Electronic type 240 Volt single phase suitable for ceiling fan step type complete as specified

S&F in replacement LED Bulb 15 Watt with lamp holder metal cased body of brass with back plate suitable for batten fittings. Make : Philips/Wipro/ Crompton/ Havell/C&S electric

Supply and fix in replacement of LED step lights complete all as specified and directed by Engr-in-Charge. Make : PHILIPS Cat Part No. BWG150 LED50/WW PSU 220-240V IP67 7043or equivalent in Wipro/Crompton/ C & S/Havell

Supply and fix in replacement of LED ceiling light recess mounting, LED luminaire 31 Watt and size of fitting 60 cm x 60 cm complete all as specified and directed by Engr -in-Charge. Make : Wipro Cat Part No CRCO10R038HP75SLAB or Philips/Crompton/Havell/C & S Electric.

Supply and fix in replacement of LED Down lighter recess mounting 5 Watt. Make : Philips cat No. MASTRER LED GU10 827 40D DIM or equivalent WIPRO/ Crompton/ Havell/C & S Electric.

Supply and fix in replacement of LED Down lighter recess mounting 8Watt. Make : Philips cat No. MASTRER LED GU10 2700K 25D KoD or equivalent WIPRO/Crompton/ Havell/C & S Electric.

Supply and fix replacement of LED luminaire 36/40 W 230 volts 50 HZ mounted with diffuser sie '1x4' approx with aceesscoires and connecting complete all as specified and directed bt Engr-in-Charge. Make : - Philips Cat No RC 869 BLED30S-6500 PSEW30L-120 D8GR.Crompton cat part No. LCPL 36 - CDL, Goldwyn Cat No. IC 0313, Wipro cat part No. CRCO 13RO38HP57G1/Havell/C&S Electric.

Supply and fixing in replacement of LED post top light with Die cast Aluminum housing in Pure Polyster UV resistant powder coated grey finish. HET PMMA diffuser, IP65 Protection, Maximum system wattage 45 watts, min. 3500 system lumens. 3 stage CCCV driver with 4kV surge protection voltage range of 150-270V AC, and connecting complete all as specified and directed at site by E.I.C. Make Wipro Cat part No: LP02-501-XXX-57-XX or equivalent in Philips/Crompton/Havell/C &S Electric.

Fixing only fluorescent tube light fitting complete energy efficient T-5 / T8 LED batten and integrated type single tube 18 / 20 Watt, 4 ft long white complete with LED rod, LED driver and LED batten etc and all accessories pre wire and connecting up with copper three core flexible cord of min size 0.5 Sqmm and PVC connector etc including provision of hanging and wall mounting as required complete light fitting including dismantling of old existing lihgt fitting complete all as specified and directed by Engr-in-Charge. Note : LED tube light fitting of any type will be issued by department free for fixing under Sch 'B'.

S & F as in replacement of existing porch light fitting any type with decorative surface mounted mirror optic with cross louvers and white engineering plastic end caps 2x36 watts CFL fitting complete with all accessories such as lamps ballast etc, all as specified and directed . Make: Crompton Greaves Cat No. TLLE 236 EB or equivalent model of Phililps/ wipro/Havells/C&S Electric/Cromption

S & Fix in replacement of existing bed light fitting with surface mounted decorative bed light fitting 1x18 watt FTL (T 8 ) complete with all accessories such as ballast , lamp holder , lamps etc including making connection with flexible copper wire twin core of size 23 /0076 all as specified and directed. Make WIPRO Cat No. WVF 90118 or equivalent model of Philips /Crompton Greaves/ Havells/C&S Electric/Cromption

S & F in replacement Mirror light fitting complete with Lamp 11 watt Make : Crompton Greaves / Model No. TLN 11 EB or equivalent model of Philips/wipro/Cromption/Havells/C&S Electric.

S & F in replacement spot light fitting angular type complete with 10 watt LED rod/lamp as per existing size complete all as specified and directed by Engr-in-Charge. Make : - Crompton Greaves/Philips / wipro/ Havells/C&S Electric.

M&L for sub main wiring with two runs of single core 4 Sqmm (nominal area) PVC insulated and unsheathed multi stranded copper conductor cable LT 1100 grade FRLS cable drawn and PVC rigid conduit 20 mm dia with all necessary fittings and accessories and run of PVC insulated and unsheathed single core cable with copper conductor of size 2.5 Sqmm as earth wire (green in colour ) run through PVC rigid conduit and connected to common earth dolly , including taking out the old sub main wiring all as specified. Note.. Two run of cable and one run of PVC conduit and one run of earth continuity wire shall be measured as one run complete all as specified

All as per item No. 200 here in before but 6 Sqmm, 2 single core with PVC FRLS insulated, unsheathed stranded copper conductor cable of size 4 Sqmm as earth lead -ditto-

S & F in replacement industrial type metal clad plug top & socket single pole and a natural link earth enclosure with MCB SP 20 Amp complete.

S & F in replacement of PVC insulated heavy duty electriic unarmoured cable with aluminium conductor, 1100 Volts grade, coroos sectional area 4 Sqmm.

Harsh Enterprises