Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹20.9 CrAccepted-AOC | ₹20.9 Cr | L1 | Accepted-AOC L1 |
| 2 | L2₹21.9 CrRejected-AOC | ₹21.9 Cr | L2 | Rejected-AOC L2 |
| 3 | L3₹2.5 CrRejected-AOC A 177 OKHLA INDUSTRIAL AREA PHASE I NEW DELHI 110020 | NEW DELHI | SOUTH EAST DELHI | DELHI | 110020 | ₹2.5 Cr | L3 | Rejected-AOC L3 |
| 4 | L4₹27.1 CrRejected-AOC DADRA AND NAGAR HAVELI DN | DADRA AND NAGAR HAVELI | THE DADRA AND NAGAR HAVELI AND DAMAN AND DIU | 396193 | ₹27.1 Cr | L4 | Rejected-AOC L4 |
Tender Value
₹22.8 Cr
EMD Value
₹32.8 L
Closing Date
17 Dec 2021, 12:00 pmClosed
Executive Engineer-I(Bldg),DNH,Silvassa
PWD Campus Block No.I(B),DNH, Silvassa
Interior Design/furnishing for District Secretariat Silvassa.(2nd Call)
2021_UTDNH_5674_1
E-TENDER NOTICE NO.32 OF 2021-22 (Bldg)
Open Tender
Civil Works - Buildings
180 days
UT OF DNH
As per NIT refer
3 documents required · 3 mandatory
₹3,000
Executive Engineer-I(Bldg),DNH,Silvassa
₹32.8 L
6 Jan 2022
4 Dec 2021
17 Dec 2021
4 Dec 2021
17 Dec 2021
4 Dec 2021
Amount
Providing and fixing foam based PVC sheet for protection of Vitrified Tile and any other type of flooring complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Providing and fixing in position Aluminum pipe framing of 50 x 50 mm, weighing 0.88 kg/mt of required square aluminum pipe dimension at 600 x 600 mm center to center both ways, with required aluminum pipe cleats and aluminum studs / brackets of aluminum pipe of required length provided at 600 mm center to center to keep framing away from wall and ceiling at required angle including cost of scaffolding as per detail. Architectural / Acoustic design and drawings complete in all aspects. (Make : TATA, JINDAL )
Providing and fixing wooden paneling with 19mm waterproof ply over existing framework including all the sundaries. (Make : Archidply, Greenlam, Century, merino)
Providing and fixing wooden paneling with 12mm waterproof ply over existing framework including all the sundaries. Make : Archidply, Greenlam, Century, merino)
Providing and fixing wooden paneling with 4mm waterproof ply over existing framework including all the sundaries. Make : Archidply, Greenlam, Century, merino)
Providing and installing storage units made out of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 9mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units should be assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges should be of Hettich/Ebco. PVC edge banding should be of Rehau or Dolken of Germany.
Providing and fixing paneling with 12.5 mm thick fire rated Gypsum board conforming to IS: 2095: part I fixed to existing framework including all the sundaries.
Providing and Fixing 4 mm thick Veneer with adhesive over existing base as per the pattern given in the drawing including all the sundaries complete in all respect to the entire satisfaction of the engineer incharge.
Providing & Fixing decorative 1.5mm thick high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality, complete in all respect to the entire satisfaction of the engineer incharge.
Providing and fixing wood Based HDF panels with lineal perforations of approved make as approved by Engineeer-in-Charge at all heights including scaffolding. The panels shall be Non FR grade with melamine laminate panels 2440mm x 128mm x18mm with 2mm slats at 15 mm pitch, Toungue and Groove edges for seamless mounting. The back of the panels fixed wtih acoustical fleece for Sound Absorption. Panel is to be fixed on armstron framework or equvelent with screw fixed horizontal or vertical to wall at every 600mm with centre & edge bracket in tongue & groove system on framework. The cavity of framework should be inserted with rock wool with 48 kg density and 25mm thickness and alongwith all accessories complete in all respect and to the entire satisfaction of Engineer in charge.
Providing and supplying Acoustical Wall Panelling with square edges made of fibre glass substrate 25mm thick and wrapped on the front side with an acoustically transparent and classified for Fire reaction Class A, as per ASTM E‐84, fabric with an option of colors – Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell as per the choice of the Architect of size 600x600mm, 600x1200mm providing a minimum sound absorption level of 0.85 NRC to be affixed to wall using Wall panel Impalers supplied by Ceiling Solutions and construction adhesives as per the instructions laid down by the manufacturer. INSTALLATION: In order to fix the panels to the wall, the Impalers shall be fixed to the wall surface using self tapping screws. 3 nos. in case of 600x600mm and 4 nos in case of 600x1200mm wall panel Impalers to be used for the installation purpose. Silica based construction adhesive to be dabbed on to the projecting elements (spikes) of the impalers. Optra wall panels shall be pierced through the spikes of the impalers ensuring the line and level of the panels are maintained. Installation to be carried out by Trained Installation team & Installation should be carried out as per recommended procedure.
Providing and Fixing Channeled Woodworks perforated panels of width 192mm, thickness of 15mm and length 2400 mm or as required by the Architect/ approving engineer, made of a Moisture Resistant fibre board with minimum 595 Kg/M3 density substrate with a laminated facing as per the approved shade & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a “Helmholtz” fluted perforation of 3mm width and 13mm of visible panel each. The edges of the panels shall be “tongue‐and grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non‐woven acoustical fleece having NRC of 0.50. The panels shall be mounted on special aluminium splines (keel) using clips provided by and approved by the Architect/ Engineer‐in‐Charge. INSTALLATION: Install wooden battens (provided by others) of section 50x50mm or as approved by the Architect on the solid wall horizontally using screws and plugs at spacing of 600mm centre‐to‐centre. Screw the aluminium extruded keel for channelled woodworks provided by over the lowest and second wooden batten at an on‐entre distance of 600mm. Install the Skirting (provided by others) of width 50mm or more as required by the Architect/ Engineer‐in‐Charge and insert the tongue end of the panel in the skirting. Place the inside clip on the groove end of the panel along the Al keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Finish off the edges using wooden moulding of matching colour (provided by others). Installation to be carried out by Trained Installation team & Installation should be carried out as per recommended procedure.
Providing and fixing of 6mm thick annealed SGG Planilaque Evolution (premium GRIHA rated lacquered glass from Saint-Gobain) of approved color by Architect/ Client / Customer, fixed with SGG Glassmate Ultrafix (compatible neutral core silicon / double sided tape) on a perfectly leveled 12mm thick water proof marine plywood / MDF / Mineral fibre board which is mounted on the RCC wall/any other structure. Lacquered glass must be made industrially (via curtain coating process); opaque (if viewed against a support wall), coated with PU lacquer ; color consistency (measured by Minolta spectrophotometer CM5081); highly durable (passes PERSOZ hardness test for minimum 220 oscillatios); humid resistant (conforms to BS EN 1036 1999); environmentally friendly (no lead, no arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial / 6% post consumer); compressive strenght (1000 MPa) & tensile strenght (40 MPa),same as float glass. all complete as per direction of Engineer-in-Charge.
Providing & Fixing 3M Etching LUMAR FILM including Plotter cutting. (Scotchcal™ ElectroCut™ Graphic Film Series 7725SE-400, Fluorescent Film) . Complete as per entire satisfaction of engineer-in-charge.
Providing & Fixing fasara glass film constructed from flexible polyester material of thickness 50 micron backing contains Acrylic pressure sensitive adhesive with Class A fire classification
Providing & Fixing 3M Controltac opaque printable vinyl with advance repositionability and Comply adhesive for bubble free application as per design approved by E.I.C
Providing & Fixing 5mm thick with bevelled edge Looking glass fix with SS studs & screws on 6mm ply panellled surface of . The looking glass shall be duly polished, grinded with smooth edges.
Providing and fixing vinyl or Polyster Textile wallpaper coverings with approved adhesive on existing plastered surface finished with putty , to give bubble free uniform surface. Any unevenness of the base surface shall be removed before fixing the wallcovering, all complete as per direction of Engineer-in-charge.
Providing and fixing 12mm thick HDF board of make GREEN, or CENTURY, or Merino including router cutting in required pattern and as per green building by-laws (as per drawing jali ) with PU( polyutherane) Finish and fixed to ply board base with C.P brass srews and washers etc all complete. as per direction of Engineer-in-charge.
Providing and fixing in position aluminium composite panel cladding in metalic colour of approved shades made out of 4mm thick material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be of approved colour and shade specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant filling in grooves in sheets, backer rods etc. complete in all respect to entire satisfaction of Engineer-in-charge.
Providing and fixing white Corian board of 12 mm thickness or equivalent with AVONITE or WILSONART with special adhesives on premium counter tops over existing RCC slabs, edges to be round and smooth complete in all respect as per Direction of of Enginee-in-Charge.
Providing and fixing of BIOFELT PLANTERS - LifeWall's patented planters made with indestructible nylon felt of 350 GSM which is UV protected. Framed on PVC backing board of 8 MM. Allows uniform watering. HSN: 8432 and DRIP IRRIGATION SYSTEM FOR VERTICAL GARDEN - Supply of suitable HDPE lateral, drip emitters, filter, joiners, etc as per the approved drawings. With automation. - Brand: Jain Irrigation HSN: 8424 and INDOOR/SEMI INDOOR PLANTS IN BIOBAGS - Suitable plants in LifeWall special growing media in Biobags. Fully trained and grown ideally for vertical garden. 1 Sqft = 4 Plants Plantation as per the approved design. Tax exempted. HSN: 0602 MS STRUCTURE - For creating a structure to hold the vertical garden. Made with Powder Coated MS Iron Rectangular Pipes. As per approved design. HSN: 7304 including transprotation and installation. as per direction by Engineering in-charge.
Providing and fixing pelmets of upto 150mm/200 mm x 150 to 300 mm L shape made of 19 mm thick ply as per drawing. Rate to be inclusive of lipping, cutting, wastages, necessary fixtures, nails, adhesives, necessary scaffolding, fixing at all heights and for all floors as per drawing and approved sample etc should also take load of all the all roller blinds.
Providing and Fixing of 100 mm thick Vertical blinds with Dust guard coated fabric complete in all respects to the entire satisfaction of the Engineer-in Charge.
Providing and fixing Sheer Dimout Blinds Blackout (Zebra blinds) construction100% Polyester fabric weight 197 GSM with repeated fabric size:Solid11.5cm/Mesh 7.5cm fabric is fixed on Anodized extruded grooved tube size 40mm O.D, the control unit is made of high strength reinforced plastic with a clutch of wrap spring design and high carbonsteel spring design . The control unit and idler should be mounted in in cassette type powder coated Headrail (As per approved sample to the entire satisfaction of Engineer-in-Charge)
Providing and fixing Roller blinds 100% Blackout , construction 3 ply PVC and1 ply Glass fibre fabric thickness 0.36 mm and weight +-520 GSM, Fire resistance NFPA 701, AATCC 16-2003 4.5 and Green guard certified with Anti fungal and Anti bacterial fabric The control unit is made of high strength reinforced plastic with a clutch of wrap spring design and high carbon steel spring design provided to transmit motion from driving to driven members of clutch The control unit and idler should be mounted on powder coated aluminium Headrail with M.S bracket to keep the fabric in Tension and straight (As per approved sample to the entire satisfaction of Engineer-in-Charge)
Providing and fixing of Somfy Premium RTS motor including remote with minimum torque 4 mm and capacity to operate single roller blinds upto 10 Sq mtr As per approved sample to the entire satisfaction of Engineer-in-Charge.
Providing and fixing of Pergo 8mm thick AC-4( average 4550 cycles) Domestic Extra series Laminate wooden flooring with Titan X Coating, impact resistance 9N, and resistance to cigarette burn with a rating of 4 (EN 438-2.05) material should be installed on Pergo combi foam and polythene complete as directed by the Engineer in-charge.
Providing and fixing artificial grass carpet made up of nylon fixed over floor or walls as per pattern given in drawing all complete as per direction of Engineer-in-charge.
Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panelssupported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of: (a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. (b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. (c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product. 11.54.2 - 450 mm Finished Floor Height (FFH).
P/F of floor carpet Mat heavy duty of superior grade and quality with 3years warranty etc. complete
Providing wood work in frames of Doors, windows cleare story windows and othersimilar works wrought, framede and fixed in position. (A) Indian Teak Wood
Providing and fixing of factory manufactured laminated doors 35mm thick including 1mm laminate on both sides. The rates also includes wooden lipping of 35mm x 5mm on all sides of the doors. The rates also incudes grooving pattern if any as per the drawing complete in all respect and the entire satisfaction of engineer in charge
P/ F of folowing hardware set complete in all respects : Two ball bearing flat button button hinge with screws for wooden doors Size : 4"x3"x3mm Material : Stainless Steel Finish: Satin, Two ball bearing flat button button hinge with screws for wooden doors Size : 4"x3"x3mm Material : Stainless Steel Finish: Satin GEZE 19mm dia Lever handle sprung loaded on with 8mm rose. Supplied with bolt through fixing. Suitable for 40 to 50mm door thickness Grub screw fixing onto 8mm x 100mm spindle. longer spindle available for thicker door. Material: Stainless Steel 304 Finish : Satin Size: 130mm x 60mm projection from door surface. ESCUTCHEON INCLUDED 55mm Backset Sash lock with strike plate. Forend : Stainless Steel 304 Finish : Satin 5 pin Euro profile key & Knob cylinder with 3 keys, 70mm
Providing & Fixing of Fixed glass partition - SG - Base Profile - 100mm - 10mm glass 3M Stock Length for 10mm Glass Black Finish as per manufacturer's specifications and complete in all respects and the entire satisfaction of Engineer-in-charge.
P/ F of specialised Aluminium Door frames i.c all the hardwares complete in all respects. The details of the frame and hardware will be as below: The door frame should be made out of SG 100mm Aluminium frame, black/silver finish including 5 no BB 4330, 5 Knuckle, 2 BB butt Hinges, Size 4" x 3" x 3mm with wooden screws-Matt Black Finish, 01 No. 7210 Lever Handle with round roses and Escutcheons, 8mm Spindle with suitable fixing screws- matt Black Finish, 01 No DL 971 Sash lock with 55mm Backset, 72mm CTC, 20 mm Square forend with Strike plate - Matt Black finish, 01 No 3515 Europrofile Cylinder on side thumb turn and other side key operation Length-70mm- Matt Black Finish 01 No TS71 Door Closure with slide channel-Black finish etc. complete in all respects to the entire satisfaction of Engineer-in-Charge. (NOTE: The above hardware is per door)
Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and makingnecessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).
Providing and fixing 150L Water Cooler: The SDLX 15150 model is a 150 liter water cooler which has a cooling capacity of 150 liter and storage capacity of 150 liter. It has two faucets. Both of them give cold water. The dimensions of the water cooler are 33 inch width, 28 inch depth and 49 inch height.
Providing & fixing of FRP Outdoor planters as per approved make & sample by Architect. Work complete including all type of material,hardware, loading,unloading,transporation, accessories etc complete as per detailed drawings, specifications & instruction, size and make as per Architect approval /EIC.
Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board.
Providing and fixing CLASSIC LITE RH 99 (Silhautte grid) 16mm false ceiling system manufactured by Armstrong using hot dipped galvanized steel section, rotary stitched main tee of size 15mm x 45 mm web height, having 0.36 mm gauge at every 600 mm centre to centre maximum and rotary stitched cross tee of size 15 mm x 45 mm, having 0.33 mm gauge at every 600 mm. c/c. and wall angle of size 19 x 19 mm., having 0.35 mm gauge fixed to the periphery of the wall. The above grid is suspended at every 600mm c/c. in both directions using 2.0 mm. thick pre-straightened GI wire laying CLASSIC LITE RH 99 ceiling tiles with Silhautte grid manufactured by Armstrong , having Humidity Resistance of 99%, RH and size 600mmx600mmx16mm over the formed grid complete. including light fixtures cutting gala in ceiling.
Providing & Fixing of Mineral Fibre Acoustical Suspended Ceiling System with 19mm thick Ultima Microlook 90 Edge Tiles with Silhouette 15mm face exposed grid in Techzone layout. The tiles shall have smooth bright laminated surface which is wipeable with dry/moist cloth with Humidity Resistance (RH) of 95%, NRC 0.70 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 40db as per ASTM E1414, Light Reflectance ≥88% as per ASTM E-1477, Thermal Conductivity k = 0.060 W/mK, Colour Global White, Fire Performance of class A2-s1, d0 according to EN 13501-1 with 19mm Microlook 90˚ edge and 8mm drop in Techzone module size of 300 x 1200mm/600X1200 (Tile) and 150/100 X 1200 mm. The 150/100X1200mm of module can be covered by AC Grille or light fixture of size which could fit in the module or 150/100 X 1200 X 0.5mm Plain GI Metal Tile. The scrim on the face of the tile shall be cleanable, soil and scratch resistant and having superior scrub-ability (Gardner Test). The tiles shall be classified as ISO 3 cleanroom class 1 with A+ VOC emissions (French). The tile shall have a rating of 8 or above for tests conducted for Resistance to growth of Mold in accordance to ASTM D3273. It shall be suitable for Green Building application, with Recycled content of 36%. The tile shall have certifications from GRIHA and GreenPro thereby confirming that it is an environment friendly product. The Silhouette Grid should have a web height of 38mm with black or white reveal. The grid should have rotary stiching and hardened steel locks on the cross tees. The layout of the grid shall have main tees at maximum 1200m apart from each other and 600mm maximum from the wall. The wall angle should be shadow moulding. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls using screws at 450mm centre to centre maximum. Installation shall be carried out as per recommended procedure. SUSPENSION SYSTEM accessories supplied by consisting of M6 Anchor Fasteners with hanger hole, pre-straightened hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs. (Optionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners).
Providing & fixing Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade 6063. The baffle blade shall be in size of 100x50x3600mm in powder coated to Woodgrain finish – Red Oak & Cherry. The baffle blade shall be suspended using Slotted U-profile of 20 x 30mm at on-center spacing 100mm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fInstallation of U-Grid: The U profile to be suspended at every 1200mm on-centre using 6mm threaded rod from the structural soffit using U-profile hanger. U-profile splice to be used to join more than one U profiles of length 3.75M. 1st U-Grid Channel must be no more than 400mm from the perimeter.ixed with End caps. Installation of Baffles: Locate the slot for Baffle Hangers in U Profile section at 1200mm centres. Hangers are inserted into the slot, and then inserted in the provision in the Al baffle. Two baffle hangers are required one on each side of the U-profile to hold the Al baffle in its place. Each Hanger to be secured into position by inserting the Locking Clip. When doing continuous installation, Baffles blades are to be connected at ends with Baffle Joiner, which are inserted into the top and bottom slots of the Baffle closed profile for alignment only. The bottom Joiner to be located first and fastened on one side only. The top Joiner to be fitted then and secured with grub screws on one side. Then the two Baffle sections shall be joined and the top Joiner isscrew fastened on the 2nd Baffle profile. End Caps to be located by pushing the End Cap tongues into open Baffle slots. Installation to be carried out by Trained Installation team & Installation should be carried out as per recommended procedure.
Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete
Providing and applying plaster of paris putty of 12 mm thickness over plastered surface to prepare the surface even and smooth complete
Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre
Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour -Two coats
Providing & applying Texture Paint including base preparation and 2 coats of acrylic emulsion as per manufacturer's specification and Complete in all respects and the entire satisfaction of engineer-in-charge.
Providing & applying polyurthene polish including rubbing, laquer filling, base preparation, Polyurthene polishing and finishing as per manufacturer's recommendation and complete in all respect to the entire satisfaction of the engineer incharge.
Providing & Installing Pictogrames & Signages for Locating the area as per design & drawings to the entire satisfaction of Engineer-in-Charge.
Providing and fixing EXECUTIVE TABLE - Signature Series with Glass top with Back Storage Unit Size : Main Table 2300 L X 1000 W x 750 H mm Size : Side Table 1400 L X 600 W x 750 H mm Table Top: 25mm thick pre laminated particle board with 2mm PVC edge lipping with sides covered with aluminium beeding in anodised finish Support: End Legs: 25mm thick pre laminated particle board with 2mm PVC edge lipping & 3 equal drawer pedetal with aluminium die cast arms.Modesty Panel: 18mm thk pre lam board with 2mm PVC edge lipping of 450mm Ht. Wire Management: 65mm dia wire manager grommet on table, flip up and provision to place CPU in side extension drawer. Back Unit - Size 1500 L x 600 W x 750 H mm Specifications Table Top: 25mm thick pre laminated particle board with 2mm PVC edge lipping with sides covered with aluminium beeding in anodised finish mounted on aluminium die cast arms Sides: 25mm thick pre laminated particle board with 2mm PVC edge lipping Back: 25mm thick pre laminated particle board with 2mm PVC edge lipping with aluminium die cast arms Shutters: 25mm thick pre laminated particle board with 2mm PVC edge lipping with brush steel handles and softclose drawer slides and hinges. approved by an Engineer in charge.
Providing and fixing EXECUTIVE TABLE - Signature Series with Glass top without Back storage unit Size : Main Table 2300 L X 1000 W x 750 H mm Size : Side Table 1400 L X 600 W x 750 H mm Table Top: 25mm thick pre laminated particle board with 2mm PVC edge lipping with sides covered with aluminium beeding in anodised finish Support: End Legs: 25mm thick pre laminated particle board with 2mm PVC edge lipping & 3 equal drawer pedetal with aluminium die cast arms. Modesty Panel: 18mm thk pre lam board with 2mm PVC edge lipping of 450mm Ht. Wire Management: 65mm dia wire manager grommet on table, flip up and provision to place CPU in side extension drawer. approved by an Engineer in charge.
Main Table PRODUCT : Connect Cabin Table Size : Main Table 2400 L X 900 W x 750 H mm Size : Side Table 1200 L X 450 W x 750 H mm SYSTEM : CONNECT, Specification : Table top : 25mm thick Pre-laminate particle board with 2mm pvc edge banding on all expossed edges. Under-structure : Supported on MS powdercoated CONNECT leg with supporting beams. Modesty Panel : 18mm thick prelam particle board Modesty panel considered on main side of front table. Wire management : 65Dia grommet. Side / Back Storage : Storages are made of 25mm Thk Table Top, 18mm Thk Openable Shutters with finger groove handle. approved by an Engineer in charge.
Common Table - 2100 PRODUCT : CABIN TABLE Size : Main Table 2100 L X 600 W x 750 H mm SYSTEM : CONNECT, Specification : Table top : 25mm thick Pre-laminate particle board with 2mm pvc edge banding on all expossed edges. Under-structure : Supported on MS powdercoated CONNECT leg with supporting beams. Modesty Panel : 18mm thick prelam particle board Modesty panel considered on main side of front table. Wire management : 65Dia grommet. Side / Back
For CEO Manager Cabin PRODUCT : DISCUSSION TABLE SIZE - 1050Dia X 750HT SYSTEM : CONNECT Specification : Table top : 25mm thick Pre-laminate particle board with 2mm pvc edge banding on all expossed edges.Under-structure : Supported on MS powdercoated CONNECT leg with supporting beams. Wire management : 350L flipup with vertical wire enry cover box.
Back Storage - 3600 L x 450 D x 750 H mm Storage : Storages are made of 25mm Thk Table Top, 18mm Thk Openable Shutters with V groove handel.
Main Table PRODUCT : Connect Cabin Table with Side Table and Mobile Pedestal Size : Main Table 2100 L X 800 W x 750 H mm Size : Side Table 1200 L X 450 W x 750 H mm SYSTEM : CONNECT, Specification : Table top : 25mm thick Pre-laminate particle board with 2mm pvc edge banding on all expossed edges. Under-structure : Supported on MS powdercoated CONNECT leg with supporting beams. Modesty Panel : 18mm thick prelam particle board Modesty panel considered on main side of front table. Wire management : 65Dia grommet. Side / Back Storage : Storages are made of 25mm Thk Table Top, 18mm Thk Openable Shutters with finger groove handle. Mobile Pedestal -PRELAM PEDESTAL 2D+ 1F SIZE : 400L X 450D X 600HT DESCRIPTION : TABLE TOP : Made of 18mm thick Pre-laminated particle board finished with 2mm PVC edge lipping. Back - 9 mm thick pre laminate particle board Edge - All exposed area with 2mm thick PVC EDGE Lipping. Handle - New finger groove handle.
PRODUCT : Connect Cabin Table with Side Table and Mobile Pedestal Size : Main Table 1800 L X 750 W x 750 H mm Size : Side Table 1200 L X 450 W x 750 H mm SYSTEM : CONNECT, Specification : Table top : 25mm thick Pre-laminate particle board with 2mm pvc edge banding on all expossed edges. Under-structure : Supported on MS powdercoated CONNECT leg with supporting beams. Modesty Panel : 18mm thick prelam particle board Modesty panel considered on main side of front table. Wire management : 65Dia grommet. Side / Back Storage : Storages are made of 25mm Thk Table Top, 18mm Thk Openable Shutters with finger groove handle. Mobile Pedestal -PRELAM PEDESTAL 2D+ 1F SIZE : 400L X 450D X 600HT DESCRIPTION : TABLE TOP : Made of 18mm thick Pre-laminated particle board finished with 2mm PVC edge lipping. Back - 9 mm thick pre laminate particle board Edge - All exposed area with 2mm thick PVC EDGE Lipping. Handle - New finger groove handle.
Back Storage 4700 Size - 4500 L x 450 D x 750 H mm PRODUCT - STORAGE Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: New finger groove handle Lock: Regular lock
Back Storage 3500 Size - 3000 L x 450 D x 750 H mm PRODUCT - STORAGE Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: New finger groove handle Lock: Regular lock
Back Storage 2800 & 2600 SIZE - 2700 L X 450 D X 750HT mm PRODUCT - STORAGE Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: New finger groove handle Lock: Regular lock
Back Storage 2100 SIZE - 2100 L X 450 D X 750HT mm PRODUCT - STORAGE Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: New finger groove handle Lock: Regular lock
Back Storage 1800 SIZE - 1800 L X 450 D X 750HT mm PRODUCT - STORAGE Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: New finger groove handle Lock: Regular lock
Back Storage 1500 SIZE - 1500 L X 450 D X 750HT mm PRODUCT - STORAGE Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: New finger groove handle Lock: Regular lock
Main Table, Return Table and Back Storage CUBICAL CABIN TABLE WITH SIDE STORAGE AND BACK STORAGE System: Neo 50 Partition 1200HT SIZE - MT1650 L X 700D, SS900L, BS2300 Specification : Table top : 25mm thick Pre-laminate particle board with 2mm pvc edge banding on all expossed edges. Partition : Neo 50 1200Ht Partition finished with Fabric tile above table top and Laminte tile below table top Return Spine Partition : Neo 50 1200Ht Partition finished with Fabric tile above table top and Laminate tile below table top Special Tiles : Each person will have one Fabric megnatic and one Glass marker tile Under-structure : 25mm thick pre particle board with matching PVC edge lipping Wire management : 65mm Dia grommet and Below Table Top 250 mm ht laminate fascia Raceway & separator for power & data cable management. MS vertical cover for wire entry. side and back storage : Made up of 18mm thick prelam particle board with sliding door & regular Cylindrical lock
Main Table & Mobile Pedestal PRODUCT : LINEAR WORKSTATION Size: 1400LX700DX1100HT SYSTEM : CONNECT Specification : Table top : 25mm thick Pre-laminate particle board E1 norms finished with 2mm pvc edge banding on all expossed edges. Screen : 18mm thick fabric magnetic screen on studs (1250LX350HT) Under-structure : Supported on MS powdercoated CONNECT leg with supporting beams. Wire management : 65mm Dia grommet and Below Table Top 250 mm HT laminate fascia Raceway & separator for power & data cable management. MS vertical cover for wire entry. Pedestal : 400LX450DX600HT PLB Pedestal (2d+1F) With Center Locking & finger GROOVE Handle
PRODUCT : LINEAR WORKSTATION Size: 1200 L X 700 D X 750 HT mm SYSTEM : CONNECT Specification : Table top : 25mm thick Pre-laminate particle board E1 norms finished with 2mm pvc edge banding on all expossed edges. Under-structure : Supported on MS powdercoated CONNECT leg with supporting beams. Wire management : 65mm Dia grommet and Below Table Top 250 mm ht laminate fascia Raceway & separator for power & data cable management. MS vertical cover for wire entry.
PRODUCT : CONFERENCE TABLE SYSTEM : PERFORM - Size 5400 L X 1500 W X 750 HT mm Specification : Table Top : 25mm Thk Table Top prelam partical board with PVC 2mm Edge Banding. Under Structure : Supported on MS Powder Coated PERFORM LEG. Wire Management : 450mm Aluminium Flip Up with soft closure and provision to mount switches and sockets on PVC Cable Dump,Vertical wire entry cover considered for Power and Data Management.
PRODUCT : CONFERENCE TABLE SYSTEM : PERFORM - Size 6000 L X 1500 W X 750 HT mm Specification : Table Top : 25mm Thk Table Top prelam partical board with PVC 2mm Edge Banding. Under Structure : Supported on MS Powder Coated PERFORM LEG. Wire Management : 450mm Aluminium Flip Up with soft closure and provision to mount switches and sockets on PVC Cable Dump,Vertical wire entry cover considered for Power and Data Management.
PRODUCT : LINEAR WORKSTATION Size: 1350 L X 750 D X 750 HT mm SYSTEM : CONNECT Specification : Table top : 25mm thick Pre-laminate particle board E1 norms finished with 2mm pvc edge banding on all expossed edges. Screen : 18mm thick fabric magnetic screen on studs(1250LX350HT) Under-structure : Supported on MS powdercoated CONNECT leg with supporting beams. Wire management : 65mm Dia grommet and Below Table Top 250 mm ht laminate fascia Raceway & separator for power & data cable management. MS vertical cover for wire entry. Pedestal : 400LX450DX600HT PLB Pedestal (2d+1F) With Center Locking & GROOVE Handel
Product - BOARD ROOM TABLE - V SHAPE SIZE : 15 SEATER DESCRIPTION : Table top : Made of 25mm thick Pre-laminated particle board finished with 2mm PVC edge lipping. Understructure : 50X50 MS PERFORM LEGS WITH MS BEAM UNDERSTRUCTURE Modesty Panel : 450 ht Prelam modesty panel Wire Manager : 450 Length Fliptop box
Product - BOARD ROOM TABLE - V SHAPE SIZE : 19 SEATER DESCRIPTION : Table top : Made of 25mm thick Pre-laminated particle board finished with 2mm PVC edge lipping. Understructure : 50X50 MS PERFORM LEGS WITH MS BEAM UNDERSTRUCTURE Modesty Panel : 450 ht Prelam modesty panel Wire Manager : 450 Length Fliptop box
For Medium Storages Size - 1500 L x 450 D x 1200 H mm PRODUCT - STORAGE Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: New finger groove - handleless Lock: Regular lock
For Medium HT Storages Size - 1200 L x 450 D x 1200 H mm PRODUCT - STORAGE Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: New finger groove - handleless Lock: Regular lock
For Medium HT Storages Size - 1050 L x 450 D x 1200 H mm PRODUCT - STORAGE Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: New finger groove - handleless Lock: Regular lock
For Medium HT Storages Size - 750 L x 450 D x 1200 H mm PRODUCT - STORAGE Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: New finger groove - handleless Lock: Regular lock
For Medium HT Storages Size - 600 L x 450 D x 1200 H mm PRODUCT - STORAGE Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: New finger groove - handleless Lock: Regular lock
Supply Leatherette Seat & Back * Liberate High Back Chair * With Head Rest * Leatherette Seat & Back * Multilock Mechanism * One Way Adjustable Arms ( Height ) * Nylon Base
Supply VISITOR CHAIR * Bravo Low Back Visitor * Leatherette Seat & Back * Fixed Arms * Powdercoated Sledge Base
Supply of 3 SEATER SOFA Leatherette upholster with chrome finish frame and legs
Supply of - 2 SEATER SOFA Leatherette upholster with chrome finish frame and legs
Supply of 1 SEATER SOFA Leatherette upholster with chrome finish frame and legs
Supply of ROUND MEETING CHAIR -
Supply of CORNER TABLE - 600 X 600 X 450 HT mm
Supply of CENTRE TABLE - 750 X 450 X 450HT
Model - ANATOM HBGS ADJ ARMS WITH HEADREST * Anatom Medium Back Mesh Chair * With Headrest * AC 60 Mesh * Fabric Upholstered Cushion Seat * Single Lock Synchro Mechanism * Adjustable Lumbar Support * One Way Adjustable Arms (Height) * Nylon Base
Model : ANATOM MBGS ADJ ARMS ( With Castors) * Anatom Medium Back Mesh Chair * AC 60 Mesh * Fabric Upholstered Cushion Seat * Single Lock Synchro Mechanism * Adjustable Lumbar Support * One Way Adjustable Arms (Height) * Nylon Base
Model : ANATOM MBGS ADJ ARMS ( Without Castors) * Anatom Medium Back Mesh Chair * AC 60 Mesh * Fabric Upholstered Cushion Seat * Single Lock Synchro Mechanism * Adjustable Lumbar Support * One Way Adjustable Arms (Height) * Nylon Base
Providing and fixing of 3 SEATER chair WITH CUSHION - FOR WAITING AREA THREE SEATER SOFA : METAL POWDERCOATED UNDERSTRUCTURE METAL POWDERCOATED SEAT & BACK WITH CUSHION FINISH IN LEATHERITE
Providing and fixing of 2 SEATER chair WITH CUSHION - FOR WAITING AREA THREE SEATER SOFA : METAL POWDERCOATED UNDERSTRUCTURE METAL POWDERCOATED SEAT & BACK WITH CUSHION FINISH IN LEATHERITE
CAFÉ CHAIRS Model : Tang Robustic Plastic moulded chair with greater durability, with multi colours options
Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) - Three phase 8 way SS Double door for horizontal single phase outgoing
Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) - (D) Single phase 6 way SS Double door
Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark - SP MCB
Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 6 to 32 Amp. - DP MCB
Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 40Amp. - DP MCB
Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 6 to 32 Amp.
Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 40 Amp.
Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 63 Amp.
Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 25 Amps.DP
Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 40 Amps.DP
Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 63 Amps.DP
Supplying & erecting approved make RCCB + MCB (Electro magnetic type only) working on residual current device having 6 KA short circuit breaking capacity and 30 mAmp. Sensitivity & 30 mili sec. tripping time conforming to IS 12640 test knob facility trip free mechanism operating for rated leakage at nominal ten volt, complete erected including all materials lugs screws etc. completed. 32A DP
Sheets steel powder coated enclosure suitable for incorporating One/Two nos. MCB.
Surge Protection Devices (SPD) Supplying, Assembling, levelling, connecting & testing following VSPs etc in boards as specified in 8.1, 8.2 & 8.3 1.4KV Protection level FP ,Class 'I', (Imax-40KA, 8/20µS) LEGRAND Cat no. 3938 or Equivalent
1.2KV Protection level FP, Class 's', (Imax-15KA, 8/20µS) LEGRAND Cat no.3943 or Equivalent
1.2KV Protection level DP, Class 's', (Imax-15KA, 8/20µS) LEGRAND Cat no. 3941 or Equivalent
Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. at 415 V. having normal current rating up to 125A. with Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only with Sheet metal Enclosure
Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. at 415 V . having normal current rating up to 250A. with variable thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only Cat III
Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 50 KA at 415 V having Normal current rating up to 400A. with variable Thermal & magnetic release suitable to work on A.C.supply 50 c/s. With all internal connections & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only Cat III
Providing and erecting metallic vitrified danger notice board for MEDIUM VOLTAGE installation to be erected as per IS.
Providing and erecting metallic vitrified danger notice board for HIGH VOLTAGE installation to be erected as per IS.
Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof thermoplastic enclosure & transparent cover erected as required with necessary connection erected as directed.
Providing and erecting approved make light control unit suitable to operate on 230V +20% having ON/OFF delay time of 30-50 seconds and having facility for Auto/manual system having two LDR lens to intensity light having capacity of 5A complete erected on section pillar with pipe and stand. Supplying & erecting power contactor for time switch complete erected as per direction Cat III 4 pole 440V 40 Amp.
Making trench in soft soil of suitable width of 90 cms deep for laying cable or locating the fault all over the run and backfilling the same and making the surface as normal ground.
Covering of cable with second class bricks or cement tiles laid cover the cable crosswise & also on both sides with covering of 7. 5 Cms. layer of sand above & below cable (16 bricks per meter)
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.(a) 4 core 2.5 Sq. mm
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.(a-1) 4 core 4 Sq. mm
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.(B) 4 core 6 Sq. mm
Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables(c) 4 core 10 Sq. mm
Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables(d) 4 core 16 Sq. mm
Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Copper lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (E) 4 core 4 Sq. mm / 4 core 2.5 Sq. mm
Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Copper lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (E) 4 core 6 Sq. mm
Supplying & laying under floor pregalvanised corrosion proof rectangular sheet steel cable trunking of 1.6 mm thick having with stand point load up to 1.33 Ton & free from seepage of concrete of screed water having following size of dimensions and No of compartments (W x D x T) : 150mm x 38mm x 1.6mm with Three Compartments
[C] G.I. Junction cross over box for metal / Al. trunking with duct entry 25mm x 38mm size having epoxy powder coated trap lead with corrosion & rust free having load bearing capacity of 3.6 TONS with adjustable levelling screw of following size.150mm x 150mm x 60/75 mm depth
[C] G.I. Junction cross over box for metal / Al. trunking with duct entry 25mm x 38mm size having epoxy powder coated trap lead with corrosion & rust free having load bearing capacity of 3.6 TONS with adjustable levelling screw of following size.300mm x 300mm x 60/75 mm depth
Supplying and erecting approved make GRP Ladder type Cable Tray Material – Corrosion Resistant Polyester Flame Retardant U.V. Stabilized Resin System - Manufactured from Pultruded Sections - Polyester Resin System, Glass Content : 55 – 60 % - Thickness- Rung Sq. Hollow Tube 25mm x 25mm - Fixing of Rung to Side Rail with Thermoplastic Pin & Epoxy Adhesive, Assembly Single Stroke 3 Mtr. Length- Rung Spacing – 300mm - Length of Tray: 3000mm- Support Span – 2500mm, Deflection L/200 or < 10mm whichever is less - Specification Followed NEMA FG1 1993- UV Resistant - Flame Retardant – IS 6746 - Appendix K/UL 94, Very Low Flammability - Oxygen Index – Minimum 30% as per ASTM D 2863 Flame Spread (Extent of Burning) – 20mm as per Standard ASTM D 635 - Tensile Strength – 4000 – 8000 Kg/Cm2 as per Standard ASTM D 638 - Flexural Strength – 2500 – 10000 Kg/Cm2 as per Standard ASTM D 790- Izod Impact Strength – 130 Kg/Cm2 as per Standard ASTM D 256- Compressive Strength – 2500 – 5000 Kg/Cm2 as per Standard ASTM D 695- Barcol Hardness – 50 – 65 (A) Width 150 mm, Side Member “C” Section : 75 x 25 x 25mm with 4mm Thickness, Loading 30Kg./Mtr. With Concentrated Load 70Kg. at center of the span
Supplying and erecting approved make GRP Ladder type Cable Tray Material – Corrosion Resistant Polyester Flame Retardant U.V. Stabilized Resin System - Manufactured from Pultruded Sections - Polyester Resin System, Glass Content : 55 – 60 % - Thickness- Rung Sq. Hollow Tube 25mm x 25mm - Fixing of Rung to Side Rail with Thermoplastic Pin & Epoxy Adhesive, Assembly Single Stroke 3 Mtr. Length- Rung Spacing – 300mm - Length of Tray: 3000mm- Support Span – 2500mm, Deflection L/200 or < 10mm whichever is less - Specification Followed NEMA FG1 1993- UV Resistant - Flame Retardant – IS 6746 - Appendix K/UL 94, Very Low Flammability - Oxygen Index – Minimum 30% as per ASTM D 2863 Flame Spread (Extent of Burning) – 20mm as per Standard ASTM D 635 - Tensile Strength – 4000 – 8000 Kg/Cm2 as per Standard ASTM D 638 - Flexural Strength – 2500 – 10000 Kg/Cm2 as per Standard ASTM D 790- Izod Impact Strength – 130 Kg/Cm2 as per Standard ASTM D 256- Compressive Strength – 2500 – 5000 Kg/Cm2 as per Standard ASTM D 695- Barcol Hardness – 50 – 65 (B) Width 300 mm, Side Member “C” Section : 100 x 35 x 35mm with 4mm Thickness, Loading 60Kg./Mtr. With Concentrated Load 70Kg. at center of the span
Supplying and erecting approved make GRP Ladder type Cable Tray Material – Corrosion Resistant Polyester Flame Retardant U.V. Stabilized Resin System - Manufactured from Pultruded Sections - Polyester Resin System, Glass Content : 55 – 60 % - Thickness- Rung Sq. Hollow Tube 25mm x 25mm - Fixing of Rung to Side Rail with Thermoplastic Pin & Epoxy Adhesive, Assembly Single Stroke 3 Mtr. Length- Rung Spacing – 300mm - Length of Tray: 3000mm- Support Span – 2500mm, Deflection L/200 or < 10mm whichever is less - Specification Followed NEMA FG1 1993- UV Resistant - Flame Retardant – IS 6746 - Appendix K/UL 94, Very Low Flammability - Oxygen Index – Minimum 30% as per ASTM D 2863 Flame Spread (Extent of Burning) – 20mm as per Standard ASTM D 635 - Tensile Strength – 4000 – 8000 Kg/Cm2 as per Standard ASTM D 638 - Flexural Strength – 2500 – 10000 Kg/Cm2 as per Standard ASTM D 790- Izod Impact Strength – 130 Kg/Cm2 as per Standard ASTM D 256- Compressive Strength – 2500 – 5000 Kg/Cm2 as per Standard ASTM D 695- Barcol Hardness – 50 – 65 (C) Width 450 mm, Side Member “C” Section : 100 x 35 x 35mm with 4mm Thickness, Loading 75Kg./Mtr. With Concentrated Load 70Kg. at center of the span
Supplying and erecting approved make GRP Ladder type Cable Tray Material – Corrosion Resistant Polyester Flame Retardant U.V. Stabilized Resin System - Manufactured from Pultruded Sections - Polyester Resin System, Glass Content : 55 – 60 % - Thickness- Rung Sq. Hollow Tube 25mm x 25mm - Fixing of Rung to Side Rail with Thermoplastic Pin & Epoxy Adhesive, Assembly Single Stroke 3 Mtr. Length- Rung Spacing – 300mm - Length of Tray: 3000mm- Support Span – 2500mm, Deflection L/200 or < 10mm whichever is less - Specification Followed NEMA FG1 1993- UV Resistant - Flame Retardant – IS 6746 - Appendix K/UL 94, Very Low Flammability - Oxygen Index – Minimum 30% as per ASTM D 2863 Flame Spread (Extent of Burning) – 20mm as per Standard ASTM D 635 - Tensile Strength – 4000 – 8000 Kg/Cm2 as per Standard ASTM D 638 - Flexural Strength – 2500 – 10000 Kg/Cm2 as per Standard ASTM D 790- Izod Impact Strength – 130 Kg/Cm2 as per Standard ASTM D 256- Compressive Strength – 2500 – 5000 Kg/Cm2 as per Standard ASTM D 695- Barcol Hardness – 50 – 65 (D) Width 600 mm, Side Member “C” Section : 100 x 35 x 35mm with 4mm Thickness, Loading 90Kg./Mtr. With Concentrated Load 70Kg. at center of the span
Supplying and erecting approved make GRP Perforated type Cable Tray Material – Corrosion Resistant Polyester Flame Retardant U.V. Stabilized Resin System - Manufactured from Pultruded Sections- Polyester Resin System, Glass Content : 55 – 60 % - - Standard Length : 3000mm- Support Span – 1500mm, Deflection L/200 - Specification NEMA FG1 1993- UV Resistant - Flame Retardant – IS 6746 - Appendix K/UL 94, Very Low Flammability - Specification Followed NEMA FG1 1993 Oxygen Index – Minimum 30% as per ASTM D 2863 - Flame Spread (Extent of Burning) – 20mm as per Standard ASTM D 635 - Tensile Strength – 4000 – 8000 Kg/Cm2 as per Standard ASTM D 638 - Flexural Strength – 2500 – 10000 Kg/Cm2 as per Standard ASTM D 790- Izod Impact Strength – 130 Kg/Cm2 as per Standard ASTM D 256- Compressive Strength – 2500 – 5000 Kg/Cm2 as per Standard ASTM D 695- Barcol Hardness – 50 – 65 (D) Width - 150mm, Pultruded “C” Channel with 30mm Sides 3mm Thickness, Loading 15 Kg./Mtr.
Supplying and erecting approved make GRP Perforated type Cable Tray Material – Corrosion Resistant Polyester Flame Retardant U.V. Stabilized Resin System - Manufactured from Pultruded Sections- Polyester Resin System, Glass Content : 55 – 60 % - - Standard Length : 3000mm- Support Span – 1500mm, Deflection L/200 - Specification NEMA FG1 1993- UV Resistant - Flame Retardant – IS 6746 - Appendix K/UL 94, Very Low Flammability - Specification Followed NEMA FG1 1993 Oxygen Index – Minimum 30% as per ASTM D 2863 - Flame Spread (Extent of Burning) – 20mm as per Standard ASTM D 635 - Tensile Strength – 4000 – 8000 Kg/Cm2 as per Standard ASTM D 638 - Flexural Strength – 2500 – 10000 Kg/Cm2 as per Standard ASTM D 790- Izod Impact Strength – 130 Kg/Cm2 as per Standard ASTM D 256- Compressive Strength – 2500 – 5000 Kg/Cm2 as per Standard ASTM D 695- Barcol Hardness – 50 – 65 (E) Width - 200mm, Pultruded “C” Channel with 40mm Sides 4mm Thickness, Loading 25 Kg./Mtr.
Supplying and erecting approved make GRP Perforated type Cable Tray Material – Corrosion Resistant Polyester Flame Retardant U.V. Stabilized Resin System - Manufactured from Pultruded Sections- Polyester Resin System, Glass Content : 55 – 60 % - - Standard Length : 3000mm- Support Span – 1500mm, Deflection L/200 - Specification NEMA FG1 1993- UV Resistant - Flame Retardant – IS 6746 - Appendix K/UL 94, Very Low Flammability - Specification Followed NEMA FG1 1993 Oxygen Index – Minimum 30% as per ASTM D 2863 - Flame Spread (Extent of Burning) – 20mm as per Standard ASTM D 635 - Tensile Strength – 4000 – 8000 Kg/Cm2 as per Standard ASTM D 638 - Flexural Strength – 2500 – 10000 Kg/Cm2 as per Standard ASTM D 790- Izod Impact Strength – 130 Kg/Cm2 as per Standard ASTM D 256- Compressive Strength – 2500 – 5000 Kg/Cm2 as per Standard ASTM D 695- Barcol Hardness – 50 – 65 (F) Width - 300mm, Pultruded “C” Channel with 50mm Sides 4mm Thickness, Loading 30 Kg./Mtr.
Fabrication : Supplying , fabricating and installation of various sizes clamps for cable tray supports using available M.S. sections & rod as per drawings or instructions of engineer in charge or consultant including applying zinc chromate yellow oxide and two to three coats of required enamel paints with anchor fasteners etc.
HEAT / FIRE RESISTANT COATING OF CABLE Supply and application of intumescent based coating on cables/ cable tray using CP 678 firestop cable coating of HILTI make or equivalent. The coating shall have a density in the range of 1.2 to 1.4 Kg/ L. The coating shall be non-toxic, asbestos and halogen free and shall have good mechanical strength. The coating shall comply with IEC 332 part 3 (1992).
Point wiring for Light Point / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.with medium class Rigid PVC pipe and accessories
Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in (a) with medium class Rigid PVC pipe and accessories Wire : (a) 2 wire 1.5 sq. mm
Additional Wire : Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in (a) with medium class Rigid PVC pipe and accessories Wire : (b) 2 wire 2.5 sq. mm
Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with primary light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories
Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling ,complete with 6A Modular type switches and following type of accessories erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary batten/angle holder or ceiling rose or H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories
Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type electronic fan regulator with separately mounted and accessories with earth continuity of following type erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories
Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories Cat. III
Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories Cat. III but for 6 A x 5 pin 250 Volt switched socket outlet point at convenient location. ( Plug & Switch can be together or at different location )
Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [II] For 6/16A Plug with 2-2.5 sq.mm Cu. Wire (a) with medium class Rigid PVC pipe and accessories
Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or Open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness
Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or Open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 32 mm rigid PVC pipe of 1.6-1.8 mm thickness
Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or Open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 40 mm rigid PVC pipe of 1.6-1.8 mm thickness
Providing & laying ISI marked Rigid PVC pipe having 6Kg / cm2 (Class-3) to be erected at road crossing on or floor as directed for laying of cable. The pipes as following size of dia & weight per 6 mtr. (B) 50 mm Dia. (2.5Kg/6RMT)
Providing & laying ISI marked Rigid PVC pipe having 6Kg / cm2 (Class-3) to be erected at road crossing on or floor as directed for laying of cable. The pipes as following size of dia & weight per 6 mtr. (D) 75 mm Dia (5.5 Kg / 6RMT)
Providing & laying ISI marked Rigid PVC pipe having 6Kg / cm2 (Class-3) to be erected at road crossing on or floor as directed for laying of cable. The pipes as following size of dia & weight per 6 mtr. (E) 90 mm Dia (8.0 Kg / 6RMT)
Supplying & erecting Electronic Type Cordless Call Bell erected on PVC/Metal board having portable bell push working on D.C. & bell on 230V A.C. supply with cells / battery
Computer : Power Plugs 1 no. universal plug-switch combined + 1 Nos swithc for Below table 2 nos. 6A 5 pin Plug as below Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories Cat. III + Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [I] For 6A Plug with 2-1.5 sq.mm Cu. Wire (Car.iii) + [II] For 16A Plug with 2-2.5 sq.mm Cu. Wire (Car.iii)
Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with following sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size ( c) with oval conduit /pvc casing capping double lock type : 4 wire 4 sq. mm
Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with following sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (e) in existing pipe (e) In existing Pipe : 4 wire 6 sq. mm
Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (e) In existing Pipe : 4 wire 10 sq. mm
Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt A.C.50 Hz 1200 mm sweep complete having 3 blades aluminium body and blade sets having ornamental design shanks , canopy & 30 cms. down rod erected with 24/0.2, 3 core flexible wire with earthing. It should be BLDC motor -5, 320RPM, 30-35W 5-Star rating Power saving Fan
Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with necessary 24/ O.20, 3 core flexible wire with earthing.
Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with square frame ABS body with inbuilt lowers & square frame.
Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM [C] 380 mm dia 1400 RPM
Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM [D] 450 mm dia 900 RPM
Supply,installation, testing and commisioning of Recccesed light fixtures suitable for Tech Zone ceiling size of 150wide x 1200mm long LED Tube light (28W) with Micro Prismatic Diffuser,4kv SPD Matt Steel Grey Extruded Aluminum Body with system luman output minimum 2800 lm. Make : Trilux, Wipro, Philips, Havells
Supply,installation, testing and commisioning of Internal light fixtures of 1200mm long LED Tube light (20W) with 110LPW white color Aluminum extruded body and milky white diffuser.Make : Trilux, Wipro, Philips, Havells
Supply,installation, testing and commisioning of Internal light fixtures of 600mm long LED Tube light (14W) with 110LPW white color Aluminum extruded body and milky white diffuser.Make : Trilux, Wipro, Philips, Havells
Supply,installation, testing and commisioning of Recessed Mounted 10W LED down light with White Aluminum dia cast, powder coated housing, reflector, PMMA Deep Down LG7 Diffuser with LED lamp and driver.LUMEN EFFICACY >90lm/W / 110lm/W, PF >0.90, THD <20%, CCT 6000K, Make : Trilux, Wipro, Philips, Havells
Supply,installation, testing and commisioning of Recessed Mounted 18W LED down light with White Aluminum dia cast , powder coated housing, reflector, PMMA Deep Down LG7 Diffuser cover with LED lamp and driver.LUMEN EFFICACY >110lm/w, PF >0.90, THD <20%, CCT 6000K, Make : Trilux, Wipro, Philips, Havells
Supply,installation, testing and commisioning of IP-65 Surface Mounted 16W LED down light with White Aluminum dia cast, powder coated housing, reflector, PMMA Deep Down LG7 Diffuser cover with LED lamp with inbuilt driver and driver. LUMEN EFFICACY >110lm/w, PF >0.90, THD <20%, CCT 6000K, Make : Trilux, Wipro, Philips, Havells
Supply,installation, testing and commisioning of Wall Mounted IP-65 2x6W LED up-down light with die cast construction, Double reflector, toughened glass cover with LED lamp and driver.-PF>0.9 ,THD <20% , Make : Trilux, Wipro, Philips, Havells
Supply,installation, testing and commisioning of Recessed Mounted 20W/Mtr LED Profile light with Aluminium die cast construction, with Micro prisamatic diffuser . LED lamp and driver.PF >0.90.THD<20 %, Make : Trilux, Wipro, Philips, Havells
Supply,installation, testing and commisioning of Recessed Mounted 3x18W LED COB light with die cast construction, Double reflector, toughened glass cover with LED lamp and driver. Make : Trilux, Wipro, Philips,, Havells
Supply,installation, testing and commisioning of 4W/Mtr LED strip light with indoor application with All require accessiers and Drivers LUMEN EFFICACY >90lm/W, PF >0.90, THD <20%, CCT 4000K, Make : Trilux, Wipro, Philips, Havells
Supply,installation, testing and commisioning of Surface Mounted IP-65 35-40W LED light with Aluminum Die cast/Extruded housng with LED lamp and driver.LUMEN EFFICACY >100lm/W, PF >0.90, THD <20%, CCT 6000K, Make : Trilux, Wipro, Philips, Havells
Supply,installation, testing and commisioning of 20W LED WALL WASHER LIGHT WITH ip-67 /IK 07protection, Aluminum dia cast BODY, 15'/55' LENSE DIFFUSER, LUMEN EFFICACY > 90lm/W, PF >0.90, THD <20%, CCT 4000K, powder coated adjustable housing, with LED Panel and driver. Make : Trilux, Wipro, Philips, Havells
Supply,installation, testing and commisioning of 600x600mm LED Panel Light of 42W LED Lamp White CRCA Luminaire Body and Micro prismatic diffuser, LUMEN EFFICACY > 120lm/w, PF >0.90, THD <20%,SPD 4kv CCT 6000K, powder coated housing, reflector, Diffuced PC cover with LED Panel and driver. Make : Trilux, Wipro, Philips, , Havells
Supply,installation, testing and commisioning of Suspended Hi-Bay IP-65 45-65W LED light with Aluminum Die cast/Extruded housng with LED lamp and driver.LUMEN EFFICACY >100lm/W, PF >0.90, THD <20%, CCT 6000K, with Liquid Cool technology Make : Trilux, Wipro, Philips, Tucana, , Havells
Supply,installation, testing and commisioning of Surface Mounted IP-65 100W LED light with Aluminum Die cast/Extruded housng with LED lamp and driver.LUMEN EFFICACY >100lm/W, PF >0.90, THD <20%, CCT 6000K, Make : Trilux, Wipro, Philips,, Havells
Supply,installation, testing and commisioning of IP-65 -IK 07 ,10-12W LED Bollard light with die cast aluminum die cast powder coated housing, reflector,with LED lamp and driver. Make : Trilux, Wipro, Philips,, Havells
Supply,installation, testing and commisioning of Wall Mounted IP-65 2x6W LED up-down light with die cast construction, Double reflector, toughened glass cover with LED lamp and driver.-PF>0.9 ,THD <20% ,Make : Trilux, Wipro, Philips, Havells
Supply,installation, testing and commisioning of IP-65 3-6W LED foot light with die cast aluminum 150-200 mm long Recessed / surfaced, IP-65 powder coated housing, reflector, toughened glass cover with LED lamp and driver. Make : Trilux, Wipro, Philips, , Havells
Supply,installation, testing and commisioning of IP-65 3-6W LED Spike light with die cast aluminum 300 mm long spike, powder coated housing, reflector, toughened glass cover with LED lamp and driver. Make : Trilux, Wipro, Philips, Havells
Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. (c) For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e independent Earthing in normal soil. Length of Pipe : 3.00 mtrs Back filling Compound :2 nos Bags of 25 Kg.
Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. (b)For Electrical installation up to 11 KV in normal soil. Length of Pipe : 2.00 mtrs Back filling Compound :1 no. Bag of 25 Kg.
Supplying & erecting of Conventional Lightening arrestor with Test loop and Counter as per IS standard
Providing and erecting required size Copper strip for earthing of H.T. OCB / ACB/ Transformer, LT panel board, Motors etc. using copper clamp.
Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG.
Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or Open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness .
Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. (8) Modem Jack for Computer Open RJ-45 - cat-III
Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. (3) Two Pin/RJ-11 Telephone Socket for One Gong Bell - cat-iii
Supplying & erecting Push button type telephone instrument (A)BEETEL Secure / BPL/, SONY / PANASONIC or equivalent make
Supplying & erecting approved make LAN cable of following size in existing pipe as per direction : [C] CAT - 6
Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of pairs. With necessary connections. (b) Armoured [Jelly Filled] - 10 Pair
Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of pairs. With necessary connections. (b) Armoured [Jelly Filled] - 20 Pair
Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of pairs. With necessary connections. (b) Armoured [Jelly Filled] - 50 Pair
Supplying, erecting, commissioning and testing EPABX CMOS microprocessor based system having common features With remote programming & remote dialling having following other common features. (Accord Matrix or equivalent approved make)- Auto Call Disconnector- (Incoming - Local- STD) with programmable timing- External Call forward with DOSA- Walk in Class of service & trunk reservation- Boss ring & call back on No Reply last caller recall CLI- Hot Line with Delay & with No.- Unsupervised Conference- Serial DISA ( DISA with option to dial another No. if Extn. is No Reply)- Programming Flexibility of all features related to timer( 41 Timer)-10 Different group of out going call restriction like 95, 97, 98 etc.Having following capacity. [E] No. Extension - 128 , No. of Junction -24 , No. of expandable ports -512 , Operators Console -01 Compatible - ISDN & Networking
Providing and erecting 1.6 - 1.8 mm thick FIA approved and ISI mark (embossed) RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following type of erection.2) For erecting concealed in RCC / Brick wall/slab or Open along with continuous fish wire to draw mains, laid in approved manner with plastering by cement mortar & finishing the surface to match the wall/ceiling. Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness .
Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. RG-6 Cable
Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. RG-11 Cable
Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. for (4) TV Co-axial Socket outlet
Supply, Installation, Testing and Commissioning of 5 Megapixel HD Dome Camera, HD1080p,1/2.7" CMOS, 24 pcs LEDs, 20m IR, Indoor IR Eyeball, ICR, 0.1 Lux/F1.2, 12 VDC, Smart IR, DNR, DWDR, 3.6mm lens, 4 IN 1
Supply, Installation, Testing & Commissioning of 2 Megapixel HD Dome Camera, HD1080p,1/2.7" CMOS, 24 pcs LEDs, 20m IR, Outdoor IR Bullet, ICR, 0.1 Lux/F1.2, 12 VDC, Smart IR, DNR, DWDR, IP66, 3.6mm lens, 4 IN 1 OUTPUT
Supply, Installation, Testing and Commissioning of 16-Channel Digital Video Recorder recording with 4TB HDD with all require installation and integration with all camera system, 16 Turbo HD input, 16-ch video&1-ch audio input, 2 SATA interface, 1280×720P: 25(P)/30(N) fps/ch, 380 1U caseW/O HDD with all require software
Supply, Installation, Testing and Commissioning of 8-Channel Digital Video Recorder recording with 4TB HDD with all require installation and integration with all camera system, 8 Turbo HD input, 8-ch video&1-ch audio input, 2 SATA interface, 1280×720P: 25(P)/30(N) fps/ch, 380 1U caseW/O HDD with all require software
Installation, Testing and Commissioning of 32" Full HD LED monitor with Power Cord complete as required & necessary video cards complete as required (if required). Make - Sony, Samsung, Philips
Supply, Installation, Testing and Commissioning Power Supply for Camera
Supplying & Laying 42U Wall mounted Rack for the CCTV DVR installation with all require power ports fixed wall rack has a tempered glass door and removable locking side panels. Included with this rack is one set of fully adjustable cage-nut style rails and removable top and bottom cable slot panels, allowing easy installation of CAT5 or fiber optic cables.
Supplying & Laying 24 port rack mounted switch for the following specfiication Approved by cUL Listed, CE, EN 60950, FCC Part 15 Class A, TUV, UL Listed 24 10/100/1000Mbps RJ45 ports
Supply Bio metric Access Control with face detection and having a memory storage of 35 days for 200 members
Supplying & erecting recess speaker with 5W rated input power 3.3 K. Ohms / 3W impedance, 100 - 10000 Hz frequency response with 6 inch dia. cone type 8 ohms speakers duly fitted in ABS plastic cabinet of colour match with wall or ceiling of following size. (a)Round Shaped, 230mm dia. Speaker Make - JBL, Harman, Yamaha
Supplying & erecting wall mounting speaker with 5W rated input power 3.3 K. Ohms / 3W impedance, 100 - 10000 Hz frequency response with 6 inch dia. cone type 8 ohms speakers duly fitted in ABS plastic cabinet of colour match with wall or ceiling of following size. (a)Round Shaped, 230mm dia. Speaker - Make - JBL, Harman, Yamaha
Supplying & erecting of Amplifier having following specification: Power Output :250W (RMS) (300W Max.), inputs : 6 Misc. & 2 Aux. frequency Response :50-1500HZ I3db, Tone Controls :Cut & Boost type LED Meter:5 LED Arrays, The amplifier suitable to operate 240V A.C.& 24volt D.C. (Battery) with automatic changeover from AC to Battery operation, duly protected by wrong Battery Polarity connections.Make - JBL, Harman, Yamaha
Supplying & erecting of Amplifier having following specification: Power Output :400W (RMS) (300W Max.) inputs : 6 Misc. & 2 Aux., frequency Response :50-1500HZ I3db, Tone Controls :Cut & Boost type LED Meter :5 LED Arrays, The amplifier suitable to operate 240V A.C.& 24volt D.C. (Battery) with automatic changeover from AC to Battery operation, duly protected by wrong Battery Polarity connections.Make - JBL, Harman, Yamaha
Supplying & erecting, Philips / Ahuja make Secretary unit comprising - 63 dBV, 7.5 mv/pa gooseneck microphone, Talk switch, Priority switch, Talk Switch LED, Ring LED indicator, connecting cable 6 core shielded, 2.5mtr long with female plug, 300 mw 8 ohms impedance speaker, connector for Delegate unit, volume control device fitted in heavy cast aluminium housing
Supplying & erecting, of 2cx1.5 Sq. mm Cu Flexible Speaker cable
Supply installation testing and commissioning High Speed quick power charging station for Trucks & Car for Electrical vehicle as per standard voltage rating with 40A FP MCB and 2 Nos 6A power plugs, it should have digital screen and all parameter recorders.
Conference Bus Cable 2M
Conference Bus Cable 20M
4K HDR TV with 4K HDR processor X1™, 4K X-Reality™ PRO and clear multi-dimensional sound 75"
Mount/ Hanging arrangement for above display.
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design TBUS-1N(B)
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design T1AF-16
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design KRT-4-H
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design KRT-4-VGA
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design KRT-4-A
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design KRT-4-USBC
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design WCP(B)
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design TS-1U
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design W-2UC (B)
Central Matrix Switcher - 6x2 4K60 4:2:0 HDMI/Audio Automatic Matrix Switcher Max Data Rate — 8.91Gbps Max Resolution — 4K Supports 4K@60Hz (4:2:0) Kramer reKlocking™ & Equalization Technology Supports Programmable Step–In over HDMI Functionality 3D Pass Through. EDID Capture Internal Pattern Generator Control — IR, RS–232, Ethernet, Contact Closure Advanced Auto Switching Embedded Web Pages Remote Button/LED Ports Independent (breakaway) Audio Routing of Digital and Analog Audio
HDMI Distribution Amplifier - 1:2 4K HDR HDMI DA 1:2 HDMI distributor Resolution — Up to 4K@60Hz (4:4:4) Bandwidth — Up to 17.82Gbps Compliance — HDR10, HDCP 2.2 Simple, intelligent EDID operation Force RGB HDCP authorization control
Wireless Presentation :Simultaneous Wired and Wireless Presentation and Collaboration Solution HDMI Input for hardwiring a computer or other HDMI compatible device Login using conventional Wi–Fi or LAN connections Powerful security features: user authentication, 1024–bit encryption, dynamic room code Supports Windows laptops and MAC, as well as iOS and Android mobile operating systems High quality video streaming, supports full HD 1080p/60 (using the VIA app Multimedia feature) Connect & collaborate with industry leading, Zoom™, BlueJeans™ and Teams™ apps Optimized for video conferencing Managed by VSM
Transmitter -4K60 4:2:0 HDMI HDCP 2.2 Transmitter with RS–232 & IR over Long–Reach HDBaseT HDBaseT 1.0 transmitter Up to 70m (230ft) at 1080p Up to 40m (130ft) at 4K@60Hz (4:2:0) Up to 4K@60Hz (4:2:0) 24bpp video resolution Control extension
Receiver -4K60 4:2:0 HDMI HDCP 2.2 Receiver with RS–232 & IR over Long–Reach HDBaseT HDBaseT 1.0 receiver Up to 70m (230ft) at 1080p Up to 40m (130ft) at 4K@60Hz (4:2:0) Up to 4K@60Hz (4:2:0) 24bpp video resolution Control extension
Controller 32–Port Master / Room Controller Supported by Kramer Control Scalable & flexible control Bidirectional RS–232 & IR with learning capability GPI/O & relay control
STREAMING SOLUTION - Encoder -4K60 4:2:0 HDCP 2.2 Video Encoder Analog audio embedding/de–embedding RS–232/IR/USB extension 16x16 video wall Reliable KVM–over IP Control via OSD menu, embedded web UI, and open API Over standard 1G network
STREAMING SOLUTION - Decoder -4K60 4:2:0 HDCP 2.2 Video Decoder Analog audio embedding/de–embedding RS–232/IR/USB extension 16x16 video wall Reliable KVM–over IP Control via OSD menu, embedded web UI, and open API Over standard 1G network
Ultra–Slim Flexible High–Speed HDMI Cable with Ethernet
USB 3.1 GEN–2 Cable USB–C (M) to USB–C (M)
Ultra–Slim Flexible High–Speed HDMI Cable with Ethernet
VGA PATCH CABLE
Ultra–Slim Flexible High–Speed HDMI Cable with Ethernet
HDBT Cable
Speaker Cable
Audio Cable/Control Cable
16U Equipment Rack for housing all rack mountable equipments with internal wiring, front glass door; heat dessipation fans; movement wheels, power distribution units etc.
Display 86 Inches Interactive DisplayDiagonal Display having 500nits brightness, 3840x2160 (UHD) resolution, Inputs port-HDMI (3), DP, DVI-D,
Conference Bus Cable 2M
Conference Bus Cable 20M
Ceiling Speakers : Full range ceiling Loudspeaker with 1 x 2.25" Driver, Freqency Response: 95 Hz to 16 kHz, Nominal Dispersion : 150˚ conical, Long Term Power Handling : 16W, Nominal Impedance: 16 Ω or 70/100V, Max SPL: 98 dB, Sensitivity: 86 dB, EN54-24 & UL compliant Installation Indoor only.
Power Amplifier : 4 channel power amplifier provides 4 x 300 W at, 4-8 Ω & 70/100V; Input Channels: 4 balanced, 2 unbalanced; Audio Output : 4; Gain : 38dB.
Digital Signal Processor : AEC capable Digital signal Processor with at least 12 AEC Mic/Line inputs & 8 analog outputs, 24 Bit A-D and D-A Convertors; Sampling Rate : 48 kHz; THD : < 0.002 % ; Channel Separation (Crosstalk) : < 108 dB ; Frequency Response 20 Hz - 20 kHz or better ; Dynamic Range > 115 dB; 5 Control Inputs and Outputs; RS-232 and Ethernet Port for third party Control and Monitoring; 64x64 Bidirectional DANTE Audio Networking ports, Shall include standard Connectivity features like VOIP, POTS, USB.
Mounting / Installation with necessary Fabrication 600 nits, cabinate material Die-Casting Aluminium, Refresh 3840 Hz
Video Conferencing includes (A) with 4-way SIP/H.323 video conferencing (B) Wireless presentation (1-User) Upgradeable to 6-users (C) Recording and streaming (D) Dual Display support (E) PTZ Camera - 12x optical zoom and (F) Speakerphones. Skype for Business client activation can be purchased separately. Two years warranty fro hardware. Extended warranty also available for purchase and Multipoint upgrade (4- way to 9-way).
Display : 65" Diagonal Trident Backlight Type LED with 400 cd/m² brightness, 3840 x 2160 (4K UHD), Built in Speaker(10W + 10W), HDMI 2.0 (2) input, HDCP2.0, USB 2.0 inputs, RS- 232.
Mount/ Hanging arrangement for above display.
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design TBUS-1N(B)
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design T1AF-16
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design KRT-4-H
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design KRT-4-VGA
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design KRT-4-A
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design KRT-4-USBC
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design WCP(B)
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design TS-1U
Table Mount Modular Multi–Connection Solution — Retractable Lid Rectangular Retractable Lid Modular Design W-2UC (B)
Central Matrix Switcher -8x8 4K HDR HDCP 2.2 Matrix Switcher with Analog & Digital Audio Routing Resolutions up to 4K@60Hz (4:4:4) Independent analog and digital audio routing Step–In over HDMI Active source detection for priority, last–connected automatic and manual switching
Transmitter -4K60 4:2:0 HDMI HDCP 2.2 Transmitter with RS–232 & IR over Long–Reach HDBaseT HDBaseT 1.0 transmitter Up to 70m (230ft) at 1080p Up to 40m (130ft) at 4K@60Hz (4:2:0) Up to 4K@60Hz (4:2:0) 24bpp video resolution Control extension
Receiver -4K60 4:2:0 HDMI HDCP 2.2 Receiver with RS–232 & IR over Long–Reach HDBaseT HDBaseT 1.0 receiver Up to 70m (230ft) at 1080p Up to 40m (130ft) at 4K@60Hz (4:2:0)
Wireless Presentation :Simultaneous Wired and Wireless Presentation and Collaboration Solution HDMI Input for hardwiring a computer or other HDMI compatible device Login using conventional Wi–Fi or LAN connections Powerful security features: user authentication, 1024–bit encryption, dynamic room code Supports Windows laptops and MAC, as well as iOS and Android mobile operating systems High quality video streaming, supports full HD 1080p/60 (using the VIA app Multimedia feature) Connect & collaborate with industry leading, Zoom™, BlueJeans™ and Teams™ apps Optimized for video conferencing Managed by VSM
Controller 32–Port Master / Room Controller Supported by Kramer Control Scalable & flexible control Bidirectional RS–232 & IR with learning capability GPI/O & relay control Supported by: Kramer Control Only
Encoder -4K60 4:2:0 HDCP 2.2 Video Encoder Analog audio embedding/de–embedding RS–232/IR/USB extension 16x16 video wall Reliable KVM–over IP Control via OSD menu, embedded web UI, and open API Over standard 1G network
Decoder:Analog audio embedding/de–embedding RS–232/IR/USB extension 16x16 video wall Reliable KVM–over IP Control via OSD menu, embedded web UI, and open API Over standard 1G network
Ultra–Slim Flexible High–Speed HDMI Cable with Ethernet
USB 3.1 GEN–2 Cable USB–C (M) to USB–C (M)
Ultra–Slim Flexible High–Speed HDMI Cable with Ethernet
VGA PATCH CABLE
Ultra–Slim Flexible High–Speed HDMI Cable with Ethernet
HDBT Cable
Speaker Cable
Audio Cable/Control Cable
22 U Equipment Rack for housing all rack mountable equipments with internal wiring, front glass door; heat dessipation fans; movement wheels, power distribution units etc.
4K HDR TV with 4K HDR processor X1™, 4K X-Reality™ PRO and clear multi-dimensional sound 75"
Mounting / Installation
Mixing Console : 10 Channel analog mixer with 4 Mic/Line Inputs ; 3 Stereo line Inputs ; 1 Aux Send ; 2 Stereo Out; 1 Monitor Out; 1 Phones; THD : 0.02%; Crosstalk : -83dB.
Central Matrix Switcher - 6x2 4K60 4:2:0 HDMI/Audio Automatic Matrix Switcher Max Data Rate — 8.91Gbps Max Resolution — 4K Supports 4K@60Hz (4:2:0) Kramer reKlocking™ & Equalization Technology Supports Programmable Step–In over HDMI Functionality 3D Pass Through. EDID Capture Internal Pattern Generator Control — IR, RS–232, Ethernet, Contact Closure Advanced Auto Switching Embedded Web Pages Remote Button/LED Ports Independent (breakaway) Audio Routing of Digital and Analog Audio
Wireless Presentation :Simultaneous Wired and Wireless Presentation and Collaboration Solution HDMI Input for hardwiring a computer or other HDMI compatible device Login using conventional Wi–Fi or LAN connections Powerful security features: user authentication, 1024–bit encryption, dynamic room code Supports Windows laptops and MAC, as well as iOS and Android mobile operating systems High quality video streaming, supports full HD 1080p/60 (using the VIA app Multimedia feature) Connect & collaborate with industry leading, Zoom™, BlueJeans™ and Teams™ apps Optimized for video conferencing Managed by VSM
Transmitter -4K60 4:2:0 HDMI HDCP 2.2 Transmitter with RS–232 & IR over Long–Reach HDBaseT HDBaseT 1.0 transmitter Up to 70m (230ft) at 1080p Up to 40m (130ft) at 4K@60Hz (4:2:0) Up to 4K@60Hz (4:2:0) 24bpp video resolution Control extension
Receiver -4K60 4:2:0 HDMI HDCP 2.2 Receiver with RS–232 & IR over Long–Reach HDBaseT HDBaseT 1.0 receiver Up to 70m (230ft) at 1080p Up to 40m (130ft) at 4K@60Hz (4:2:0) Up to 4K@60Hz (4:2:0) 24bpp video resolution Control extension
Controller 32–Port Master / Room Controller Supported by Kramer Control Scalable & flexible control Bidirectional RS–232 & IR with learning capability GPI/O & relay control Supported by: Kramer Control Only
Encoder -4K60 4:2:0 HDCP 2.2 Video Encoder Analog audio embedding/de–embedding RS–232/IR/USB extension 16x16 video wall Reliable KVM–over IP Control via OSD menu, embedded web UI, and open API Over standard 1G network
Decoder -4K60 4:2:0 HDCP 2.2 Video Decoder Analog audio embedding/de–embedding RS–232/IR/USB extension 16x16 video wall Reliable KVM–over IP Control via OSD menu, embedded web UI, and open API Over standard 1G network
Ultra–Slim Flexible High–Speed HDMI Cable with Ethernet
USB 3.1 GEN–2 Cable USB–C (M) to USB–C (M)
Ultra–Slim Flexible High–Speed HDMI Cable with Ethernet
VGA PATCH CABLE
Ultra–Slim Flexible High–Speed HDMI Cable with Ethernet
HDBT Cable
Speaker Cable
Audio Cable/Control Cable
12 U Equipment Rack for housing all rack mountable equipments with internal wiring, front glass door; heat dessipation fans; movement wheels, power distribution units etc.
Adarsh Infrainterio Pvt Ltd
Ahluwalia Contracts (India) Ltd.
SHANTI PROCON LLP
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid