Renovation of Civil Works, Fixtures and Gas Distribution In District Food Laboratory, Karnal Sector-16 Karnal

Amount

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar (HSR 5.7.4)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1: 1.5:3 or richer mix (i/c equivalent design mix) (HSR 5.23.1)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm ( HSR-10.63.2) (Tiles will be supplied by the department.)

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1 :4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete (HSR-10.57)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to ISI15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1 :3 (1 cement : 3 coarse sand) and jointing with grey cement slurry@ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete ( HSR-10.62)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : For fixed portion. Anodised aluminium (anodised transparent or kg dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) (HSR-12.157.1.1)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or kg dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) (HSR-12.157.2.1)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides ( HSR-12.158.2)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item).With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) ( HSR-12.159.2)

Providing and fixing ISi marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete 75x63x4 mm (HSR 12.97.6) (Labour Rate)

Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm (HSR 12.98.1) (Labour Rate)

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete. 150x10 mm (HSR 12.99.4) (Labour Rate)

Providing and fixing 50 cm long aluminium kicking plate of size 100x3.15 mm, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc.complete. (HSR 12.101)

Providing fixing aluminium round shape handle of outer dia 100mm with screws etc. complete. Powder coated minimum thickness 50 micron. (HSR 12.108.2) (Labour Rate)

Providing and fixing aluminium hanging floor door stopper, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc.complete. Single rubber stopper (HSR 12.103.1 )

Providing Aluminium Jali of thickness 7mm thick with openings - 75mm X sqm 75mm of including anodizing and fixing in frame with cost of screws etc ( HSR-12.107)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight up to 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness (HSR-12.160.1)

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance i!: 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main 'T'. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. With 16 mm thick bevelled tegular mineral fibre Antimicrobial false ceiling tile confirming to ISO 5 (class 1 00 ) specifications ( HSR-32.47.3)

Replacing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete ( HSR-30.64)

Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. Complete (HSR-12.81)

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 356 4, embossed on the body, door weight up to 35 kg and door width up to 700 mm), with necessary accessories and screws etc. complete (HSR-12.88)

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS: 3564 ,embossed on the body, door weight up to 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete (HSR-12.89)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or Strap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous chinaware Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests ( HSR-22.22.1) (Labour Rate)

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.10 litre capacity - White ( HSR-22.39.1)

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete: White solid plastic seat with lid ( HSR-22.36.1)

Providing and fixing white vitreous chinaware flat back or wall comer type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. One urinal basin with 5 litre white P.V.C. automatic flushing cistern (HSR-22.25.1) (Labour Rate)

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) including Rack Bolt Screw Pair 115mm long without CP fittings complete in all respect. Size 450mmx300mm (HSR-22.221.1) (Labour Rate)

Providing and fixing white vitreous chinaware pedestal for wash basin completely recessed at the back for the reception of pipes and fittings ( HSR-22.5) (Labour Rate)

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet. 150 mm diameter ( HSR-22.102.2) (Labour Rate)

Providing and fixing toilet paper holder. C.P. brass ( HSR-22.42.1) (Labour Rate)

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. ( HSR-22.119) (Labour Rate) 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. ( HSR-22.119.2)

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms ( HSR-22.119.1)

Providing and fixing PTMT stop cock of approved quality and colour (HSR-22.112.1.1) Labour Rate

Providing and fixing PTMT soap Dish Holder having length of 138mm breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms (HSR-22.127) Labour Rate

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (ofapproved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete (HSR-22.209)

Fixing C.P. brass bib cock of approved quality conforming to IS:8931( HSR-22.104.1 ) Labour Rate

Fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms (HSR-22.106.1) Labour Rate

Fixing brass stop cock of approved quality. 15 mm nominal bore (HSR 22.97.1) Labour Rate

Fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of Engineer-in-charge). Two way (HSR 22.8.2) Labour Rate

Fixing in position best Indian make C.P. brass Tooth Brush cum Tooth Paste Holder fixed in with rawl plugs with C.P. brass screws complete including cutting and making good the walls etc. Tooth Brush-cum-Tooth Paste holder ( HSR 22.213.1) Labour Rate

Providing and fixing kitchen sink including making all connections excluding cost of fittings.White glazed fire clay sink of size 600x450x250 mm ( HSR-22.13.1)

Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISi : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately ( HSR-22.182)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. (HSR 22.88) 15mm dia (HSR 22.88.1)

20mm dia (HSR 22.88.2)

Laboratory Module 750 with C-Frame complete in all aspects :- Providing and Fixing Complete set C-Frame based Modular Under benchs suspended storage Unit of Double door and single drawer with Cam lock Size should be width 750mm x depth 530mm x height 635mm, The whole unit must be fabricated in 0.9mm 120 GSM GPSP/GI sheet metal with adjustable shelf. The whole unit must pure epoxy powder coated with 70-800micron thickness. The must consist of SS/PP hinges, Drawer should be fitted with Hettich/Hafele/godrej sliding channels and SS Door handles. 'C" Frames should have D-700 x W-30 mm H-780 (Sitting) & H-890mm (Standing) Vertical Legs depending on as actual site requirements. Connecting Sets member arms should be made GPSP/GI 120GSM in 1.2mm thickness and 5mm end profile conectin to C frames. Worktop should be Z Black Granite 17 (±1) mm thick with pre moulded and polished edges. The overhang of granite should be 30 mm – 50mm. at front side of under storage cabinets, Neoprene Strip (2.5'' wide & 6 mm thick) backing material for granite should be NEOPRENE fixing with SR-998 glue, As required the cover Panel End side panel for main unit, 600mm D, 900mm Ht. The whole unit must be complying to SEFA 8M standards. Test report must be submitted. Bidder should have ISO 18001:2007, ISO 13485:2016, ISO 14001:2015, ISO 9001:2015, OHSAS, BIFMA. The bidder must submit work order copy of similar work in any Govt. institute/Establishment. (NS)

Laboratory Leg Space 750mm with Back Cover Panel as arequired complete unit : Providing & Fixing with SITC of Leg Space of L-750 with Back Cover panels. The whole unit should be made from 0.9mm GPSP/GI sheet metal with pure epoxy powder coating 70-80 micron. Worktop should be be et black Granite (Acid/Chemical Resistance)17 (±1) mm thick with high quality granite in jet black colour with pre moulded, pre polished edges abd shamphering. The overhang of granite should be 30 mm – 50mm. at front side of under storage cabinets, Neoprene Strip (2.5'' wide & 6 mm thick) backing material for granite should be NEOPRENE fixing with SR-998 glue. Complete in all respect as directed and upto the entire satisfaction of Engineer in Charge. The whole unit must be complying to SEFA 8M standards. Test report must be submitted. Bidder should have ISO 18001:2007, ISO 13485:2016, ISO 14001:2015, ISO 9001:2015, OHSAS, BIFMA. The bidder must submit work order copy of similar work in any Govt. institute /Establishment. (NS)

Laboratory 600mm PP Sink Module with acessories complete : Providing and fixing of 600mm under bench suspended sink storage unit of width 600mm, Depth 530 mm, ht of unit 635 mm with two shutters. The whole unit must be pure epoxy powder coated 70-80micron coated 0.9mm metal sheet GPSP, Cabinet shutter must be fitted with SS/PP hinges, SS Door handles of approved make. The Polypropylene Sinks (Drop-in) of overall size 500L x 398W x 235D (mm) or as per site black color classic timeless appearance in matt finish, non rusting and easy to maintain with bottle trap. Waste Coupling For PP/Ceramic. Anti-Siphon bottle trap, Size : 38mm dia. (Black color) Serated Flexible connector to connect sink to the waste line, length 1mt. and 38mm dia. Brass epoxy coated water faucets for Sink unit shall have 3 way (2 straight+1 swan neck) turn type water faucets. It should be PH and rust resistant with PP regulators, has detachable hose nozzles, allay pressure, changeable high-pressure outlet constructed or normal clean outlet control of water flow faucet immediately. Worktop should be be et black Granite (Acid/Chemical Resistance)17 (±1) mm thick with high quality granite in jet black colour with pre moulded, pre polished edges abd shamphering. The overhang of granite should be 30 mm – 50mm. at front side of under storage cabinets, Neoprene Strip (2.5'' wide & 6 mm thick) backing material for granite should be NEOPRENE fixing with SR-998 glue. Complete in all respect as directed and upto the entire satisfaction of Engineer in Charge. The whole unit must be complying to SEFA 8M standards. Test report must be submitted. Bidder should have ISO 18001:2007, ISO 13485:2016, ISO 14001:2015, ISO 9001:2015, OHSAS, BIFMA. The bidder must submit work order copy of similar work in any Govt. institute/Establishment. (NS)

Laboratory Module 600 with C-Frame complete in all aspects :- Providing and Fixing Complete set C-Frame based Modular Under benchs suspended storage Unit of Double door and single drawer with Cam lock Size should be width 600mm x depth 530mm x height 635mm, The whole unit must be fabricated in 0.9mm 120 GSM GPSP/GI sheet metal with adjustable shelf. The whole unit must pure epoxy powder coated with 70-800micron thickness. The must consist of SS/PP hinges, Drawer should be fitted with Hettich/Hafele/godrej sliding channels and SS Door handles. 'C" Frames should have D-700 x W-30 mm H-780 (Sitting) & H-890mm (Standing) Vertical Legs depending on as actual site requirements. Connecting Sets member arms should be made GPSP/GI 120GSM in 1.2mm thickness and 5mm end profile conectin to C frames. Worktop should be Z Black Granite 17 (±1) mm thick with pre moulded and polished edges. The overhang of granite should be 30 mm – 50mm. at front side of under storage cabinets, Neoprene Strip (2.5'' wide & 6 mm thick) backing material for granite should be NEOPRENE fixing with SR-998 glue, As required the cover Panel End side panel for main unit, 600mm D, 900mm Ht. The whole unit must be complying to SEFA 8M standards. Test report must be submitted. Bidder should have ISO 18001:2007, ISO 13485:2016, ISO 14001:2015, ISO 9001:2015, OHSAS, BIFMA. The bidder must submit work order copy of similar work in any Govt. institute/Establishment. (NS)

Providing and Fixing Laboratory Corner Unit with accessories Complete Unit : Corner Modular Floor Unit corner module main unit, 850mm x depth 530mm x height 635mm Epoxy powerder coated 0.9mm metal sheet/1.2mm verticle leg support in virgin steel GPSP/GI 120GSM. Worktop should be Z Black Granite 17 (±1) mm thick with pre moulded and polished edges. The overhang of granite should be 30 mm – 50mm. at front side of under storage cabinets, Neoprene Strip (2.5'' wide & 6 mm thick) backing material for granite should be NEOPRENE fixing with SR-998 glue, As required the cover Panel End side panel for main unit, 600mm D, 900mm Ht. The whole unit must be complying to SEFA 8M standards. Test report must be submitted. Bidder should have ISO 18001:2007, ISO 13485:2016, ISO 14001:2015, ISO 9001:2015, OHSAS, BIFMA. The bidder must submit work order copy of similar work in any Govt. institute/Establishment. .(NS)

Providing and Fixing Laboratory Corner Sink Module with accessories Complete Unit : Corner Modular Floor Unit corner module main unit, 850mm x depth 530mm x height 635mm or as per the site dimensions. Whole unit must be made from GPSP/GI 0.9mm sheet metal with two shutters fitted with 2 sets of SS/PP hinges, and SS Door handles. The whole unit must be pure epoxy powder coated 70-80micron coated 0.9mm metal sheet GPSP, Cabinet shutter must be fitted with SS/PP hinges, SS Door handles of approved make. The Polypropylene Sinks (Drop-in) of overall size 500L x 398W x 235D (mm) or as per site black color classic timeless appearance in matt finish, non rusting and easy to maintain with bottle trap. Waste Coupling For PP/Ceramic. Anti-Siphon bottle trap, Size : 38mm dia. (Black color) Serated Flexible connector to connect sink to the waste line, length 1mt. and 38mm dia. Brass epoxy coated water faucets for Sink unit shall have 3 way (2 straight+1 swan neck) turn type water faucets. It should be PH and rust resistant with PP regulators, has detachable hose nozzles, allay pressure, changeable high-pressure outlet constructed or normal clean outlet control of water flow faucet immediately. Worktop should be be et black Granite (Acid/Chemical Resistance)17 (±1) mm thick with high quality granite in jet black colour with pre moulded, pre polished edges abd shamphering. The overhang of granite should be 30 mm – 50mm. at front side of under storage cabinets, Neoprene Strip (2.5'' wide & 6 mm thick) backing material for granite should be NEOPRENE fixing with SR-998 glue. Complete in all respect as directed and upto the entire satisfaction of Engineer in Charge. The whole unit must be complying to SEFA 8M standards. Test report must be submitted. Bidder should have ISO 18001:2007, ISO 13485:2016, ISO 14001:2015, ISO 9001:2015, OHSAS, BIFMA. The bidder must submit work order copy of similar work in any Govt. institute/Establishment. (NS)

Laboratory Single Reagent Shelf for Acids & Chemicals Single Sided Reagent Shelf 2-tier size 150mm wide shelf size should be complete modular design with adjustable shelves. Each reagent rack pillar should be of 700mm (H) x 120mm(D) x 50mm(W) size made from 100 x 50 Rectangular Sheet metal Slotted section of 1.2mm thickness on both sides of the pillar. Shelves of the reagent shelf should habe brackets fitted in the pillar slots for adjustments. It should have provision for removable Cover for easy access during repair of hidden parts. Shelves frame should be made from 1mm thick Sheet metal fitted on angle profile to rest the Granite/PRL/Glass Sheet/1mm GPSP sheet. Electrical trunking should made from 0.8mm thick GPSP Sheet with cutouts for Switch/Sockets and other accessories and provision for gas line to pass through. Each component should have 70-80 micron epoxy powder coating resistant to corrosion. Provision for gas distribution should be made in the reagent trunking.(NS)

Laboratory Double Reagent Shelf for Acids & Chemicals Single Sided Reagent Shelf 2-tier size 150mm wide shelf size should be complete modular design with adjustable shelves. Each reagent rack pillar should be of 700mm (H) x 120mm(D) x 50mm(W) size made from 100 x 50 Rectangular Sheet metal Slotted section of 1.2mm thickness on both sides of the pillar. Shelves of the reagent shelf should habe brackets fitted in the pillar slots for adjustments. It should have provision for removable Cover for easy access during repair of hidden parts. Shelves frame should be made from 1mm thick Sheet metal fitted on angle profile to rest the Granite/PRL/Glass Sheet/1mm GPSP sheet. Electrical trunking should made from 0.8mm thick GPSP Sheet with cutouts for Switch/Sockets and other accessories and provision for gas line to pass through. Each component should have 70-80 micron epoxy powder coating resistant to corrosion. Provision for gas distribution should be made in the reagent trunking.(NS)

Fume Hood Body: System should be single body type design constructed from GI sheet metal only. The main body of the system should not in two piece design i.e upper structure and lower structure. Both lateral sides of the system should have provision for two open able panels for easy maintenance of gas and water utilities. The back panel should also be possible to remove and open. Reaction Monitoring Interface Device- The fume hood must include an in built interface with devices which are capable of controlling the heating process of at least four reactions simultaneously within a specified time frame. The temperature range should be (ambient to 250°C) and the time should be from 0 to 999 minutes with a precision of ±1 oc. The heating process will stop automatically upon process completion. Sash System: Fume hood should have an electronically controlled sash system which should work in synchronization with the air flow monitoring of the system. Sash should have sliding mechanism on front pillars. Lubrication free sash system should be vertically sliding on the front pillars pulley system with linear dry bearings on anodized aluminum profile having 30-40mm width and 700 N static load rating along with belts/wire driven with counter weight balance. The counter weight must not be visible at the back side of the system. The back panel should be open able for maintenance. The frame of Sash should be 1mm GPSP/GI sheet metal with 50mm wide frame rim size fitted with 5-6 mm thick toughened glass. Sash should not be visible on the top of the fume hood system when open. Sash moving mechanism should have provision to upgrade to automatic sensor based opening and closing at site by the manufacturer/supplier. Sash handles must be rust resistant. Minimum Inside chamber dimension and design: Free-standing rigid frame structure of steel (GPSP/GI only) 1.2mm and 1.6mm respectively shall be provided to support exterior panels and interior liners & baffle panels. The inner chamber should be having off white color backalite/HPL 12mm sheet duly sealed with epoxy at the joints. Inner Liner: Interior liner panels must have minimum 12 thick phenolic resin high pressure laminate or 12mm backalite fixed on GPSP/GI sheet metal frame from outer side panels using stainless steel screws with plastic covered heads. Front Utilities Pillars & Facia: Fume hood system should have continuous front facia pillars with 4 cut-out with removable cover on each side for hosing the gas, water and electrical and other utilities. Baffle: A stable, non-adjustable baffle shall be provided to aid in distributing the flow of air into and through the hood. The design of the baffle should be ergonomic. The baffle shall be spaced out 3-4 inches from the back wall of hood. The baffle shall be removable for cleaning. Air foil: A streamlined airfoil shall be integral at the bottom of the hood opening on bench and distillation hoods. This foil shall provide a nominal 1” open space between the foil and the top front edge of the work surface to direct an air stream across the work surface to prevent back flow of air. The air foil mist have slotted cutouts for smooth flow of air when sash is closed. Air Volume: System should be having Constant Air Volume at 100 fpm (feet per min.) is 630 cfm (cubic feet per minute) or better. Air Velocity Monitoring System: System should be having TEL/Siemens or equivalent air flow monitoring system, make Tel/Siemens. (NS)

FUME HOOD COMPLETE UNIT WITH ACCESSORIES Fume Hood (with base) Extra Heavy Structure made of 1.6 mm frame & 1.2 mm GPSP body Over all Size L=1200mm, D=900mm, H=2300 mm consisting of following: 1. Should complied to ASHRAE110:2016 AM or equivalent 2. Fume Hood Upper Unit should be Epoxy Polyester Powder Coated and dimensions should be L=1500mm, D=940mm, H=1450mm. 3. Fume Hood (Upper Unit) should have internal lining suitable for Acidic Fumes of Internal size L=1180mm, D=810mm, H=1220mm 4. System should have Baffle at the back with 3 point suction system (for light, normal & heavy gases/ Fumes) for smooth exhaust of fumes. 5. Should have Sash-vertical sliding 5 - 6mm thick toughened glass in a 50mm wide frame. Sash should slide on a pulley system and Sash should also have SS handles for operation. 6. Should have for 6/16 amps single phase socket with 16 amps MCB, internal wiring, LED light, On-Off switch for Blower, tube light switch, ELCB for Safety Purpose 7. Worktop should be Jet black Granite: 16-17mm dished work surface with 12mm thick ply backing having provision to fix Drip cup. 8. UTILITY SERVICES – Should have remote valves on front fascia and spout on the inside wall. (All utility line shall be terminated at rear side on top /bottom of fume hood for further connection). 9. Wet and Dry Service Utilities (as per DIN 12920 norms) 10. Panel Mounting for Water, Gas, Vacuum, Nitrogen supplies in the fume hood should be standard along with gas valves and water faucet. 11. Fume Hood Base cabinets should be C-Frame design with dimensions as L=1500mm, H=850mm x D-570mm + Frame of depth 900 mm 12. Fume should be quoted with suitable blower wit branded motor drive system with 1400CFM to 1800CFM, body of fume Hood should be PP or FRP. 13. Required chemical resistant ducting should be quoted with the system. 14. Fume Hood must be quoted with apparatus holding grid. 15. Base storage cabinets should be having the internal PP+FRP lining to avoid the corrosion. 16. Door handles should be made of SS304/316. The manufacturer must be ISO, BIFMA, OHSAS and SEFA-10 compliant. (NS)

Ducted Chemical Storage Unit Complete with all accessories Providing and Fixing CHEMICAL STORAGE CABINETS as per following specifications:- MS Chemical Storage Cabinet 1000 x 486 x 1800mm : 1.2mm thick made of GPSP with epoxy coating (60-70 micron). Four Door Cabinet with glass MOC : MS GPSP 1000mm W x 486mm D x 1800mm Ht. Inside must be polyprylene + Fiber reinforced plastic coatong 3mm quoting (NS)

DUCT PP+FRP (polypropylene+ Fiber reinforced plastic) Complete PPFRP 14” Rigid duct with acessories for Fume Hoods: PP+FPR ducting with 3mm PP inner side and 3mm FRP outer side. Ducts should be 25 mm x 25 mm Stitch welding is done on inner surface and continuous welding on outer surface. While making the lining, there should not be any air pockets or any sort of uneven finish. The flange thickness should be 8mm. All flanges are to be matched with M8, GI fasteners and flat washers on both the sides. 90 degrees bend of 14 inches, U-clamps for Rigid Duct 14 inches, Flange 10mm thick round with fasteners PP+FRP for 14” duct, Hanging MS Support for Rigid Duct 14", Flexible Bellow for the blower, Raincowl for blower system, Inlet Transition for blower system, per Running meter cost should be mentioned. (NS)

Providing and Fixing of GPSP epoxy powder coated electrical raceways for with the provision for face plate housing for one 5Amp and one 16 Amp socket and two 5Amo ad 15amp switches each. Raceways should be made of 1 mm thick GPSP (NS)

SS 316 1/2" Gas Fittings complete Providing and fixing of SS 316 ¼” size gas tubing with hanging clamp support complete as directed and up to the satisfaction of engineer incharge (NS)

SS 304 Cylinder Manofold Gas Fittings Providing and fixing of SS 304 Cylinder Manifold with pigtail, MS cylinder mounting bracket complete (NS)

SS 316 T-Joint connectors Gas Fittings Providing & Fixing SS 316 T-Joint connectors complete as directed and up to the satisfaction of Engineer in Charge (NS)

Control Valve Box with pressure gauge meter Gas Fittings Providing & Fixing Control Valve Box with pressure gauge meter complete as directed and up to the satisfaction of Engineer in Charge.(NS)

SS 316 Needle Valves for 1/2” with SS connector and fitting Gas Fittings Providing & Fixing SS 316 Needle Valves for 1/2” with SS connector and fitting complete (NS)

3 Stage Purification Panel Gas Fittings complete Providing & Fixing purification panel with control valves with pressure gauge (for N2, Argon, Helium, Hydrogen gas) complete as directed and up to the entire satisfaction of Engineer in charge (NS)

LPG line SS 1/2" with connector & Bunsen burner assembly Providing and fixing of LPG line with with SS 316 1/2" tubing, Hangin clamp support, Argon welding of joints, parallel line for each lab from cylinder bank, LPG Gas regulartor manifold, bunsen Burners with flame control and on –off facility with brass construction and powder coated base 13mm brass pipe, LPG brass manifold for cylinders (NS)

Gas Cylinder Filled Gas Cylinder 47lt capacity ea with valve of analytical grade purity 99.999& pure for H2, He, N2, O2, Zero Air, Argon, MS cylinder bank with priming coat and water proof paint dual coat. Firesaftey certificate, Purity certificate must be attached (NS)

Providing and fixing of (L) 450mm and W 450mm SS304 exhaust hood with tube and connector for the chemical and fume exhaust along with PP/GI blower, 1 HP Motor with 1000CFM capacity. (NS)

Providing and fixing of PP/GI blower with 1 HP 1000CFM motor with fan impeller unit for ducted storage along with damper (NS)

providing fixing and installation of Sport Fume extractors roof mounted. The arm pipe should be of anodized aluminium material. Air volumes: 45-85 m3/h. Working in -5' C+90'c. Rings, samper and Joints should be made of poloypropylene material, movable in one direction. Thread screw should be SS material. Should handle small amount of chemical fumes, pollutants in chemical and physical science laboratories. Suitable blower of 1 HP motor for 2 nos. of spot fume extractor should be quoted. (NS)

Providing and fixing of Antivibration table for analytical balance with 0.001 and 0.01mg (NS)

Providing and fixing of double head eye wash (NS)

Providing and fixing of SS 304 Body wash with foot/hand control switch with fittings and acessories. Unit must be chemical resistant (NS) Note:- 1. In case of any difference in the unit & nomenclature of any of the HSR Items of Civil, P.H. work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable.

Advent Technologies