SPL REPAIR OF OR GOVT MD ACCN BLDG NO P OR 668 01 06 AT SAITAN SINGH VIHAR IN SUKNA AND CERTAIN OTHER SANCTIONED WORKS IN SUKNA MIL STN UNDER GE SUKNA

Amount

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying of cable, erection of poles etc. not exc. 10 Sqm on plan and not exceeding 1.5 m in depth getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing Excavated soils not exc 50 M and depositing where directed at a level not exc1.5 M above the starting point complete all as specified and directed.

M&L for Plain Cement Concrete Type C2 1:2:4 (using 40 mm graded stone aggregate) in surface channels and drains including all necessary form work complete all as specified and directed.

M & L for plain Cement Concrete Type B0 1:2:4 (using 12.5 mm graded stone aggregate) in roof kerbs, rounded or chamfered on haunching in chajjas to prevent water seepage into brick walls, including necessory formwork (upto height of 8 mtr) rounded or chamfered on edges complete all as specified and directed.

M&L PCC 1:3:6 type B-1 (using 12.5 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L Precast Reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) in landing, cover slabs (for manholes etc), chullah hoods, chajja, water troughs, mangers, shelves and similar articles with plain faces and set in cement mortar 1:4 including necessary forms, moulds etc. complete all as specified and as directed.

M & L for providing Reinforced cement concrete (1:2:4) type B-1 Nominal Mix using 20 mm graded stone aggregate as in slab supported on walls ,beams and coloumns in floors,roofs,landings, kitchen slabs etc complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately.)

M & L for providing Reinforced cement concrete (1:2:4) type B-1 Nominal Mix using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately.)

M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified.

M&L for repair to broken/damaged RCC chajjas by making good with PCC 1:2:4 type B1 or rendering 15 mm thick in cement mortar 1:4 mixed with water proofing compound to top and sides and rendering 5 mm thick to soffits in cement mortar 1:3 including necessary formwork reinforcement duly welded if required including demolition of broken/loose PCC or taking down old plaster at any storey of building upto 12 mtr height complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like laid over and including screed bed 15 mm thick in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and complete all as specified and directed.

M&L 18 to 20 mm thick granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and complete all as specified and directed.

M&L for rough finished flat formwork to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc. 200 mm thick (horizontal or sloping) work as rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with MDF board exterior grade, commercial type on both side and covered on both side with decorative face veneer with liping/frame to match complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wire gauze in lieu of plain colour PVC sheet. The wire gauze shall be wrapped on an additional square 8mm MS Solid tube and this tube shall be welded to MS tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F factory made solid PVC Moulded door shutter with particle board core, 28 to 30 mm thick (style) with 2,4, or 6 raised panel design with 2mm thick Moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face suppling and fixing in the frame at site as per specification & drawing on SI page No. 161 of SSR Part-II complete all as specified and directed.

S & F factory made Solid PVC double door frame of size 50 mm X 95 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F Continuous (Piano) hinges, mild steel, bright finished or electro galvanized, width of flaps (When open) 30 mm complete all as specified and directed.

S & F 300 mm long ordinary rat tail pattern springs including roller and roller plate complete all as specified and directed.

S & F 125 mm long brass handles, cast type, polished bright fancy type fixed with brass screws complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repair stainless steel towel rail 600 mm long of brass chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S & F Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm complete all as specified and directed.

S&F in repairs stainless steel derocative curtain rod of 25 mm bore with wood fineshes including brackets 2 nos fiunnlel caps 2 Nos etc complete all as specified and directed.

S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F in repairs kitchen plate rack made out of stainless steel 0.63 mm thick sheet with partitions and size of rack 800 x 250 x 900 mm with shape and pattern as per sample kept in Sample room of GE Office complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tank and similar work confirming to Fe-290 Gde E-165 Complete all as specified and as directed by Engr-in-Charge.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5 mm to 10 mm dia.,cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S & F Hard drawn steel wire fabric weight exc 4Kg per Sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt complete all as specified and directed.

S & F Rolled Mild Steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe – 410 – W(Gde E - 250) quality 'A' complete all as specified and directed.

S & F of pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S & F of pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

M&L anodised Aluminium frame for door, window, Cup board and ventilator with bone or more rebates including jointing cleats for fixing etc complete all as specified and directed.

M&L anodised Aluminium door, window, Cup board and ventilator shutter and frame any type (Sliding or openable) with frame and other similar work, fabricated aluminium mesh etc. aluminium heavy section favricated incl all necessary roller wheels, cleats, handle, locking arrangement and arrangement to fix wire mesh with aluminium channel beading and stainless steel screw incl cost of rubber gasket ,beading roller wheel etc. complete Note-(a) the wt of rubber gasket beading, roller wheels, etc will not be measured with the wt of alumium shutters as only aluminium item shall be measured .(b)wire mesh shall be measured and paid saparately (c) Aluminium hinges shall be included in the unit rate

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F veneered decorative 12mm thick plywood, grade I (with BWR rasin) with decorative face veneers 0.9mm thick lamination on both face fixed with screws or adhesive to plywood surfaces as in cupboard, drawer, kitchen cabinet etc including taking down old one complete all as specified and directed.

S&F veneered decorative 19mm thick plywood, grade I (with BWR rasin) with decorative face veneers 0.9mm thick lamination on both face fixed with screws or adhesive to plywood surfaces as in cupboard, drawer, kitchen cabinet etc including taking down old one complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25 mm (minimum) thick as single piece in in treads, flooring etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab and including rubbing and polishing and laid over 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L machine cut kota stone slab 20-25 mm thick as in skirting, dado, riser of steps, plinth, etc, laid over and including 15 mm thick backing in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the stone complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) finished even and smooth without using extra cement as in plinth protection/path laid in alternate bays and construction joints to be given at every 3M interval and corners of buildings and filled with Sealing compound Grade ‘A’ complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type D-2 (using 40 mm graded crushed stone aggregate) as in sub floor, sub base of floor, paving, path etc complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in sub base of flooring etc complete all as specified and directed.

M&L Coloured glazed ceramic tiles 300x 450x 7 mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick backing with cm 1:4 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 finish even and rough complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm in cement mortar 1:6 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but n. Exc. 0.38 sqm, as in skirting/dado on vertical surfaces over etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including backing 10 mm in cement mortar 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and fair complete all as specified and directed.

M&L for rendering 15 mm thick in two layers 10mm and 5mm on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth using WPC compound in top layer complete all as specified and directed. Note:- WPC shall be measured and paid separatley.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick works or concrete surface finished even and smooth without using extra cement provided at the junction of RCC and brick work in plaster in internal surfaces shall be provided with stainless steel wire mesh (chicken mesh wire netting 25 gauge) in plaster etc complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on ceiling, chajja finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M & L for painting the new Ceiling surface complete all as specified and directed as follows :- (a) Surface Preperation- Preperation of new ceiling surface of ceiling. (b) Putty application- NIL. (c) Priming surface- NIL. (d) Painting- Applying three coats of white wash.

M & L for painting the old ceiling surface complete all as specified and directed as follows :- (a) Surface Preperation- Complete removal of existing old plastered or previously untreated surfaces of ceiling. (b) Putty application- NIL. (c) Priming surface- NIL. (d) Painting- Applying three coats of white wash.

M&L for complete removal of existing treatment of old decorated wall surfaces by Vacuum based sanding machine, removal of nails etc & filling cracks / hole with putty, applying one coat of primer using auto roller and applying a thin layer of wall care putty and sanding the same by Vacuum based sanding machine till obtaining even and smooth finish and applying two coats of oil bound distemper by auto roller complete all as specified and directed as per manufacturers instructions. Note:-Multipurpose mixer shall be used for uniform and proper mixing of putty.

M&L for preparation of newly plastered surfaces of wall by Vacuum based sanding machine, applying one coat of primer using auto roller and applying a thin layer of wall care putty and sanding the same by Vacuum based sanding machine till obtaining even and smooth finish and applying two coats of oil bound distemper by auto roller complete all as specified and directed as per manufacturers instructions. Note:-Multipurpose mixer shall be used for uniform and proper mixing of putty.

M&L for preparation of newly plastered surfaces of wall by Vacuum based sanding machine, applying one coat of primer using auto roller and applying a thin layer of wall care putty and sanding the same by Vacuum based sanding machine till obtaining even and smooth finish and applying two coats of exterior weather coat paint using auto roller complete all as specified and directed as per manufacturers instructions. Note:-Multipurpose mixer shall be used for uniform and proper mixing of putty.

M&L for complete removal of existing treatment of old decorated wall surfaces by washing with jet washer machine, removal of nails etc & filling cracks / hole with putty, applying one coat of primer using auto roller and applying a thin layer of wall care putty and sanding the same by Vacuum based sanding machine till obtaining even and smooth finish and applying two coats of exterior weather coat paint using auto roller complete all as specified and directed as per manufacturers instructions. Note:-Multipurpose mixer shall be used for uniform and proper mixing of putty.

S&F 4 mm thick obscured/ frosted / pin headed glass in ventilator shutters not exc 0.50 sqm in each pane complete all as specified and directed.

S&F 4 mm thick plain sheet glass ordinary quality fixed with aluminium frame work Not exc 0.50 sqm in each pane complete all as specified and directed.

M & L for painting the old steel surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of old steel surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- NIL (c) Painting- Applying one coats of synthetic enamel paint.

M & L for painting the new steel surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of new steel surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- Applying one coat of red oxide primer (c) Painting- Applying two coats of synthetic enamel paint.

Taking down any layer of existing water proofing treatment including plaster, PCC of any thickness complete all as specified and directed.

M & L for 15 mm thick screeding / rendering in cement mortar 1:3 on concrete roof surface, using water proofing compound @ 2% by weight of cement, surface finished even and smooth without using extra cement complete all as specified and directed. Note : Water Proofing Compound shall be measured and paid seperately completed all as specified and as directed.

M & L for cleaning the plastered / concrete surface with wire brush and applying water proofing treatment as under :- (a) Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning (b) Laying APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) land on primed surface by forced application complete all as specified. (c) Overlap for APP membrane shall be 75mm on longitudinal direction and 100 mm on transverse direction. (d) Finally applying a coat of solar reflective bituminious aluminium paint @ 0.15 complete all as specified and directed.

M&L Cleaning top surface of floor slab and vertical surface of wall and brushing with neat cement slurry @ 0.5 kgs of cement per sqm with acrylic based polymer modified cementitous composte at the rate of 0.25 kg/sqm and laying 50 mm thick (average) PCC of grade M-10 (Nominal mix) mixed with WPC as per manufacturer instruction laid in slops 1:20 towards spouts including covering corners. (ii) Rendering 15 mm thick in cement mortar 1:4 on wall / floor surfaces of sunken floor finished even and smooth with using WPC as per manufacturing instruction and brushing with neat cement slurry @ 0.25 kgs of cement per sqm with acrylic based polymer modified cementitous composite at the rate of 0.13 kg/sqm complete all as speciifed and direted. (iii) Applying a coat of paving bitumen 80/100 penetration @ 1.50kg/sqm on plastered & concrete surfaces. (iv) Laying a layer of 200 micron polythene film pasted with the help of suitable.

Taking up or down 15 mm dia steel tubing and connections, complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, complete all as specified and directed.

Taking up or down 25 mm bore steel tubing and connections, complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 25 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc.) and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

M&L in repairs High dencity polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to wall,ceiling or floors etc.40 mm bore pipe complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 500 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

S & F in repair 15 mm bore bib tap chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15 mm bore bib tap, two way, fancy type chromium plated, cast copper alloy, with crutch or butterfly handle and wall flange, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs central hole basin mixer, brass, chromium plated, for mixing hot and cold water, with 450 mm Long Braided Hoses, screwed down for 15 mm bore pipe complete all as specified and directed.

S&F in repair brass CP wall mixer chromium plated 15 mm bore with capstan head, screwed down high pressure with or without lettered “hot’ or “ cold” with long screwed shanks and fly nuts, connecting legs and wall flanges screwed for iron pipe as complete all as specified and directed.

S & F in repair 15 mm bore stop valve / angle valve fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S&F in replacement 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in replacement 25 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs Ball valves 25mm dia high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 25 mm - 455 gms) complete all as specified and directed.

S & F in repairs Grating doom 100 mm dia with waste hole of PTMT. (Minimum weight 25gms) complete all as specified and directed.

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipe complete all as specified and directed

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, incl bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe complete all as specified and directed

S & F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius, fixed with cement solvent, with oval access door complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius, fixed with cement solvent, with oval access door complete all as specified and directed.

S & F 75 mm bore PVC (SWR) branch piece single, (single Y) equal or unequal, with oval access door complete all as specified and directed.

S & F 110 mm bore PVC (SWR) branch piece single, (single Y) equal or unequal, with oval access door complete all as specified and directed.

S & F 75 mm bore PVC (SWR) junction single, (single T) equal or unequal, fixed with cement solvent, with oval access door complete all as specified and directed.

S & F 110 mm bore PVC (SWR) junction single, (single T) equal or unequal, fixed with cement solvent, with oval access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

M & L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 100 mm bore complete all as specified and direct

M & L for PCC 1:3:6 type c2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore pipe complete all as specified and directed.

M & L 100 mm dia Salt Glazed stone ware drain pipes laid in trenches and jointed in CM 1:1 complete all as specified and directed.

M & L 150 mm dia Salt Glazed stone ware drain pipes laid in trenches and jointed in CM 1:1 complete all as specified and directed.

S&F in repairs sink without drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495 x 420mm bowl size 410 x 330 x 160 mm and including 32 mm waste pipe & coupling complete all as specified and directed.

S&F in repairs vitreous china water closet pan (semi-pedestal pattern) anglo indian type white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs swivel shower rose size 125 mm of brass chromium plated any colour (minimum weight 40 gms) for fixing with 15mm dia steel pipe complete all as specified and directed.

S&F in repairs vitreous china wash basin white flat back size 550 x 400 mm excluding taps waste chain, plug and porcelain stopper but including brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed.

S&F in repairs soap dish, with metal dish brass chromium plated fixed to plugs complete all as specified and directed.

S & F for in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F Factory made 24mm thick 100% solid WPC (Wood polymer composite) JALI of required size comprising of virgin PVC resin of K value 58-60 (suspension grade) calcium carbonate and natural fibers (wood powders / rice husk/wheat husk) and non toxic additives, made from extrusion process WPC foam sheet single extruded (inner) with having miniumum density not less than 650 kg/cbm, having good screw holding capacity (screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum compissive of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category with property of being termite / borer free, water / moisture proof and fire retardant, WPC jali to be fixed with stainless steel butt higes (if required) of required size with necessary full body threaded star headed counter sunk SS screws or fixed with iron frame with screws all as per direction of Engineer-in-charge, For Interiors / Kitchen shutters / Balcony & Internal doors and partitions.

S&F Stainless steel zero crank hinges (auto) fancy type with mounting plates & cover caps fixed to shutters in cupboards of standard size and shape for modular kitchen complete all as specified and directed by Engr-in-charge.

S&F 500 mm deep black finish drawer channel including of rooler for moving drawer precision full extension runner with pull -out stop and roll-out guard, powder coated steel black complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided including padding concrete on roof all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling Unframed timber scantlings 40 Sqcm and over in section and in any position in framed work complete all as specified and directed.

Dismantling boarding of any description fixed in any position with nails complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Demolition and breaking up drain pipes AC 100 mm internal dia set in cement mortar complete all as specified nad directed.

Demolition and breaking up drain pipes AC 150 mm internal dia set in cement mortar complete all as specified nad directed.

Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed by Engr-in-Charge.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, modular plate and frame on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch, all necessary cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. Note :- (i) Making good to match with the adjoining surface shall be included in the unit rate. (ii) Cutting chases shall be included in the unit rate.

All as per Sl. item No. 135.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on independent board.

All as per Sl. item No. 135.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on same board.

All as per Sl. item No. 135.00 above but for one light point controlled by two, 2 - way switches complete all as specified and directed

All as per Sl. item No. 135.00 above but for one 16 Amps socket outlet point on independent board with 2.5 sqmm cable and 2.5 sqmm earth wire

M&L point wiring with 2.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including PVC casing caping (double lock pattern) and accessories on wall / ceiling surfaces etc. with and including 2.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc including all other fixing accessories for one light / fan / exhaust fan point controlled by one 5 / 6 Amps switch complete all as specified and directed.

M & L in replacement concealed sub main wiring with 2 runs of 4.00 sqmm main wire along with 1 run of 4.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories fixed on wall/ceiling surface, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

S&F switch piano modular type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano modular type one way, 15 /16 Amps independent, 240 volt complete all as specified and directed.

S&F switch piano modular type two way, 5 Amps independent, 240 volt complete all as specified and directed.

S&F modular type Bell push 6 A , 1 module complete all as specified and directed.

S&F socket outlet modular type 3 pin 5 / 6 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F socket outlet modular type 3 pin 15/16 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F in repair electronic modular fan regulator, stepped type( 4 step), white 120 W - 2 module complete all as specified and directed.

S&F switch socket combination 5 pin 16 Amp, flush type universal complete all as specified and directed.

S&F MCB SP 6 to 32 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB SPN 40 Amp , 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB TPN 63 Amp, 10 kA, 240V 'B' curve complete all as specified and as directed.

S&F MCB ,TPN DB, 04 ways double door,Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete including blanking plates as required & fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed

S&F MCB ,SPN DB, 12 ways double door,Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed

S&F ceiling rose, surface bakelite 65 x 50 mm three terminal complete all as specified and directed.

S&F angular type lamp holder, PVC/Polycarbonate type with back plate suitable for Led lamp complete all as directed.

S & F Bell, AC. 230 volts, single pole completed all as specified and directed.

M &L in replacement Earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick, buried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connected using galvanised iron earth lead wire 4 Sqmm as earthing electrode by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe (medium grade) and other end connected to earthing test point as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C both ways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth up to a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be made again by the contractor at no additional cost and including dimantling complete all as specified and directed.

S&F ventilation fan 250 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including self closing louvres, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed.

Supply and fix of energy saving 1200 mm sweep BLDC ceiling fan complete with all connected accessories as specified below: - Input Power :- 26 watts with full speed and reduced power consumption with reduced speed technology. Voltage :- 90-300 V AC, 50Hz, single Phase. RPM :- 340 to 375 rpm Blades :- Decorated Sweep :- 1200 mm. Air delivery :- Not less than 210 CFM Colour :- Glow white/Toast Brown/Gloss Black/or others as approved by Engr-in-Charge Speed/power contro :- Without Remote through existing regulator Star rating :- BEE 5 Star Rating Warranty: - As specified by the manufacturer, contractor shall produce original warranty and test certificate from the manufacturer.

S&F for Metal Plug Socket DB with sheet metal enclosures with two pin and earth plug and socket one double pole MCB 20 Amps,240V for Geysor connenction complete all as specified and as directed. Make-Legrend/Anchor or equivalent.

S & F in repairs LED Bulk Head fitting 10 watt with Injection molded polycarbonate housing IP66, IK10, 3.5kV inbuilt surge protection, PF =0.95, total System Lumens not less than 1100 lm, 6500k CRI = 80, Operating Voltage range 140 V - 270 V. complete all as specified and as directed. Make- Havells , Cat No- RUGBYGENXFTS10WLED865SSYMBOPC or equivalent Make of Philips / Crompton .

S & F in repairs of LED Light fittting 1 x 20 watt ,220 V AC PVC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper cableof suitable size complete all as specified and as directed.

S&F in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

M&L for painting of ceiling fans, any type size after taking down complete in situ with synthetic enamel paint by spraying, including filling cavities with filler, one coat after cleaning all dust etc and refixing the fan to its original positioing including providing suitable size clamps & down rods for hanging and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

Supply, installation commissioning of glass top deep freezer, swing door inbuilt lighting, single phse 240 volts 50 Hz of capacity 205/220 ltr complete all as specified and directed. Make :- Voltas, Bluestar, HITACHI, Godrej or equivelent.

Supply, installation, commissioning of refrigerator 260 Ltr, 3 star smart inverter frost-free double door refrigerator with stabilizer free operation complete all as specified and directed. Make :- VOLTAS / Whirlpool / LG / Blue star / samsung or equivelent.

R K UDYOG (BID ID -3421705)

ASHISH ROY (BID ID -3420622)

M/S EASTERN ENGINEERING (BID ID -3420471)

MS UNITY CONSTRUCTION CO (BID ID -3421405)

DAS AND GHOSH CONSTRUCTION (BID ID -3421202)

VICKY ENTERPRISES (BID ID -3420997)

SHIVALAYA ENTERPRISES (BID ID -3419684)

A K ENTERPRISES (BID ID -3420763)