Replacement of One motor for Lift Irrigation scheme Verinag

Design, Manufacture, Supply, Installation, Testing & Commissioning of Horizontal Centrifugal Pumping unit to be installed at the existing Lift Irrigation Scheme Verinag. The pumping unit shall have the following specifications: - PUMP: - Make Kirloskar, WPIL, M&P, Jyoti, SINTEH, Flowmore/or any equivalent make Discharge = 2.5 Cusec (0.07079 m3/sec) Dynamic Head = 56 m. Speed = 1480 RPM Type of pump = Horizontal Split Casing Centrifugal. NPSH A at site = 3.60 m MATERIAL OF CONSTRUCTION: Impeller = Bronze grade V of IS: 318/ CF-8M Wearing Ring = Bronze grade V of IS: 318/CF-8M Impeller Shaft = Stainless Steel AISI 410 Gland = Bronze grade V of IS: 318 Fasteners = High tensile Steel Shaft Sleeve = Stainless Steel AISI 410 Pump Casing = Close fine-grained Cast-Iron conforming to IS:210 Grade 20 Coupling = Tyre coupling of suitable size Base frame =M. S fabricated as per IS 2062 Motor Specifications: - Type---------------Horizontal Type Squirrel Cage Induction Motor No of phases-------------------------03 Horse Power----------------------as per design but not less than 85 HP Speed---------------------------------1480 RPM Enclosure-----------------------------TEFC Rated Voltage------------------------415 ±10% Rated Frequency--------------------50±3% Class of Insulation---------------------“F” Temperature Rise------------ Limited to class B Type of Duty--------------------------Continuous Motor efficiency .......... ≥IE2 Make: KEC/ABB/Siemens/Bhel/Crompton/Marathon/Jyoti/Havells The job includes coupling of the Motor with the Pump by way of providing and fitting of a suitable size tyre coupling with allied works and necessary modifications required, if any for fitment of the Pump Motor assembly to existing delivery and suction of diameter 150mm and 125mm respectively. The job includes costs on account of all duties, taxes, freight, transportation, transit insurance, handling, tools and tackles and consumables required for carrying out the said job and dismantling of old worn-out equipment. The Pumping unit shall have to be got predispatch inspection by the Third-Party Inspection Agency namely CEIL, RITES, NTH, TUV and the Certificate of the same shall be provided at the time of the supply of the equipment, for which the scope has been kept in the estimated cost. Note: The pump curves of the quoted pumping equipment need to be uploaded by the tenderer at the time of tendering. The Govt. Circular of Finance Department issued vide No. DGAT/PS/DR/7865508/86 Dated: 06-03-2026 shall be applicable

Design, Manufacture, Providing, Fitting, testing and commissioning of 100 HP 3 Phase Fully Automatic Star Delta Motor Starter. The Star Delta Motor Starter panel shall be fabricated out of 1.6 mm (minimum) CRCA sheets and shall be Modular, free standing, floor mounted or wall mounted for indoor use having removable bottom gland plates for incoming and outgoing cables, dust and vermin proof (IP 55 protection) with Three Phase Aluminium Bus Bars, complete with connections, internal wiring and other accessories with painting etc as per the details furnished below: - Rated voltage of the panel ------------------ 415±10%volts Frequency ------------------------- 50 ±3Hz No. of phases ----------------------- Three. Distribution Bus Bar: - Type ----- Electric Grade Aluminium insulated with Red, Blue, Yellow and Black Shrinkable Sleeves of adequate section. Size ----- Adequate section as per requirement Starters (FASD) 100 HP with minimum ratings as below: Power specifications --- 3 phase 415±10 %& 50 ±3Hz Contractors ------------ L&T/TC/BCH Make Line contactors -------- as per design but not less than AC3 95 A Star conductor --------- as per design but not less than AC3 80 A Delta contractor ------- as per design but not less than AC3 95 A Thermal over load relay ------- (66-110 A) or above as per requirement Timer -------------- Star Delta Electronic Protection: - Overload &Under load protection Single phase & Reverse phase protection Unbalance voltage protection Earth fault protection Metering Display Details shall display Parameters: Phase Voltage, Phase Current, Line voltage etc Accessories and wiring: - a) Pushbuttons & elements: - Quantity: As per requirement such as for Starter start & Starter stop etc b) Pilot Lamps: For Phase Indication, Motor ON/ OFF and Trip indication etc NOTE: - The panel should be powder coated with Siemens grey colour. The Govt. Circular of Finance Department issued vide No. DGAT/PS/DR/7865508/86 Dated: 06-03-2026 shall be applicable