CONSTRUCTION OF PT SHED FOR JL WING, THE INF SCHOOL UNDER GE BELGAUM

Amount

Surface dressing n. exc. 15cm deep in hard/ dense soil all as specified and directed.

Excavation over areas n. exc. 1.5 m depth for foundation, levelling, etc. and getting out in any type of soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in soft/ loose soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in hard/dense soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in soft/ disintegrated rock all as specified and directed.

Returning filling in including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for hard core with broken stone or boulders of gauge n.exc 63mm, deposited, spread, levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces all as specified and directed.

M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for plain cement concrete 1:4:8 type D2, using 40mm graded stone aggregate in foundation, filling, mass concrete, levelling courses and sub bases all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10cm width, blocks cast in PCC 1:3:6 type C0, using 12.5mm graded stone aggregate, set in CM 1:6 complete all as specified and directed.

M&L 40mm thick plain cement concrete 1:2:4, type B0, using 12.5mm graded stone aggregate as in damp proof course to horizontal or vertical surfaces over a coat of blown type bitumen applied ebenly at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m including use of necessary formwork all as specified and as directed.

M&L for pre-cast plain cement concrete 1:2:4, type B1, using 20mm graded stone aggregate as in kerbs provided on edges of pathways including all necessary forms and moulds with plain fair faces and chamferred edges all as specified and directed

M&L for Reinforced cement concrete M-25 grade (Design mix), using 20mm graded stone aggregate as in foundation, column footings, plinth beams, etc all as specified and directed.

M&L for Reinforced cement concrete M-25 grade (Design mix), using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels, bands and the like all as specified and directed.

M&L for Reinforced cement concrete M-25 grade (Design mix), using 20mm graded stone aggregate as in Columns, pillars, piers, posts and strutsand the like all as specified and directed.

Supply only approved integral water proofing compound all as specified and as directed.

M&L for use of form work to sides of concrete foundations, column footings, plinth beams and similar works for rough finished flat concrete surfaces, vertical or to batter, all as specified and directed.

M&L for use of form work to sides of pillars, posts, struts, columns, etc. for fair finished concrete surfaces, square, rectangular or polygonal all as specified and directed.

M&L for use of form work to sides and soffits of roof beams, tie beams, lintels, bands and similar works for rough finished flat concrete surfaces all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

All as descrbed in item No. 21 but 6mm to 10mm dia as in stirrups, spacers and binders all as specified and directed.

M&L for main and cross beams, hip and jack rafters, purlins where connected to common rafters, with rolled mild steel beams, tees, angles, channels or flat sections fixed with angle cleats or other connecting plates, complete conforming to Fe 410W (Gde E-250) quality B all as specified and as directed.

M&L for framed roof trusses, trussed, purlins, with rolled mild steel beams, tees, angles, channels or flat sections including distance pieces, cleats etc. complete conforming to Fe 410W (Gde E-250) quality B all as specified and as directed.

M&L for mild steel flats as in wind ties for roof including securing bolts and necessary drilling, conforming to Fe-290 Gde E-165 all as specified and as directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 all as specified and as directed.

S&F Mild steel screw bolts (machine made), n exc 30cm long and 16 to 20mm dia neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, all as specified and as directed

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in ridges, valleys, hips, claddings, etc. fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for 100mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base for flooring including finishing the surface even and fair all as specified and directed.

M&L for 40 mm thick plain cement concrete 1:2:4 type B1 using 20mm graded aggregate as in floor, finished even and smooth with using extra cement all as specified and directed.

M&L for 3mm thick glass dividing strips, 38mm wide, inserted in position, conforming to design all asspecified and as directed.

M&L for coloured decorative cement concrete tiles 30cm x 30cm x 25mm thick, with glossy/ rubber boulded finish on top, set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. complete all as specified and directed.

M&L for 80mm thick machine pressed precast concrete interlocking paver blocks with glossy/ rubber moulded finish on top, M-40 grade, any shape and size confirming to IS 15658-2006 all as specified and directed.

M&L for crushed stone sand (M-sand/ Robo sand/ I-sand) as in cushioning for interlocking paver blocks including watering and consolidating complete all as specified and as directed.

M&L for plain cement concrete 1:3:6, type C1, using 20 mm graded stone aggregate, 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar etc. complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for three coats of white wash, on newly plastered surfaces of walls, beams, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and directed.

M&L for two coats of cement based paint, any colour, on newly plastered surfaces of walls, beams, pilasters, cornices, etc., over a coat of primer including necessary preparation of surfaces all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC conduit/ PVC casing capping of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including 1/2 module PVC surface mounting box with standard white modular cover plate & frames for mounting modular type switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed.

All as described in item No. 42 but for one fan point controlled by one switch and regulator.

All as described in item No. 42 but for one 05 Amps socket outlet on independent board.

All as described in item No. 42 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 42 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC conduits/ PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Two runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

S&F modular switch, 1 module, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular switch, 1 module, 1 way, 16 Amps, 230 volts, AC, all as specified and directed.

S&F modular socket outlet, 2 module, 6 Amps 2 cum 3 pin multipurpose all as specified and directed.

S&F modular socket outlet, 2 module, 16 Amps 3 pin 16 Amps cum 3 pin 5 Amps multipurpose all as specified and directed.

S&F in ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F modular fan regulator, step type, 2 module, 120 Watts, 230 volts, AC, all as specified and directed.

S&F MCCB DB VTPN 4 Way, vertical type, suitable for MCCB as incomer 415 volts rated bus bars double door type including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCCB DB on board complete all as specified and directed.

S&F MCB DB SPN 8Way without bus bars single door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCCB TPN 125 Amps, 25KA, 415 Volts, AC supply, fixed thermal magnetic settings, all as specified and as directed.

S&F MCB SPN 6-32A 10KA 50Hz 240 Volts AC supply all as specified and as directed.

S&F MCB SP 6-32A 10KA 50Hz 240 Volts AC supply all as specified and as directed.

S&F surface mounting LED light fitting, 1x 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 20W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP65 protection, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F ceiling fan, 230 volts, single phase, 1200mm sweep, 3 blades, with all accessories complete all as specified and as directed. Make: HAVELLS Model No. ES-50 or equivalent model in makes CG/ ORIENT

M&L for XLPE insulated, armoured, heavy duty electric LT UG cable with multi-stranded aluminium conductor, 1100 Volts grade, cross sectional area 16 Sqmm x 4 core, laid in trenches/ passing through pipe/ duct or fixed to wall including provision of necessary lugs/ thimbles/ ferrules, connecting up , testing and commissioning complete all as specified and as directed. Note: Excavation, earth work, cable cushioning, bricks/ GI pipe for protection shall be measured and paid separately under relevant items of this schedule.

M&L for double wall corrugated HDPE pipes, conforming to IS 14930-2001, ISI marked, 63mm outer dia, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches/ under roads/ crossing etc. all as specified and as directed.

M&L for GI tubes, light grade, 40mm bore, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches / under roads/ crossing etc. all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

M/s B C CHOUGULE

RAJENDRA KRISHNA SARAF

M/s. N D KALING

Shri Sai Associates, Laxmiwadi

Vinod Enterprises

A. N. Kalbhavi

M/S MAHADEV M PATIL

ASHIRWAD ELECTRICALS