SPECIAL REPAIR TO BLDG NO S AND T 49 LPG SHED AT 304 (I) SUP PL ASC AND HARD STANDING WITH FIXING OF INTERLOCKING TILES AT THE REAR SIDE OF BLDG NO MH 1 HOSP WARDS OF MH AND PROVN OF CERTAIN MINOR AND REVENUE WORKS AT JUTOGH CANTT UNDER GE JUTOGH

Amount

Excavation in trenches not exc 1.5 m wide and n.exc 1.5m in depth in Hard/dense soil complete all as specified and as directed.

Excavating over areas, n exc 1.5 m deep and getting out in Hard/ dense soil complete all as specified and as directed.

Returning , filling in spreading and levelling and well ramming in layers not exc 25cm including watering for filling under floor complete all as specified and as directed.

Removing of excavated material (soils, etc) outside MoD land and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and as directed.

Excavating in post holes in hard/dense soil (or similar holes) each n. exc 0.50 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25cm, watering and removing surplus soil to a distance n exc 50m and making good surface complete all as specified and directed.

M&L for PCC 1:2:4, type B-2, using 40mm graded crushed stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for 25mm thick, PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in flooring, finish rough to receive floor finishes etc. complete all as specified and directed.

M&L for 100mm thick, PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in flooring / base etc. complete all as specified and directed.

S & F structrual steel rolled sections as in main and cross beams, hip and jack rafters; purlins, post, gusset plate, (angle, channel, beam, flat, tubes) where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe-410W ( Gde E-250) Quality B, complete all as specified and directed.

M&L for coloured Non - skid Ceramic tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and incl 15mm thick screed bed in CM 1:6, finished even and rough to receive tile complete all as specified and directed. Note : Colour of tile will be approved by GE.

M&L for coloured Non - skid Ceramic tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and incl 15mm thick screed bed in CM 1:6, finished even and rough to receive tile complete all as specified and directed. Note : Colour of tile will be approved by GE.

M&L for coloured Non - skid Ceramic tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, on vertical surface as in dado/ skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, fixed over and incl 10mm thick rendering in CM 1:4, finished even and rough to receive tile complete all as specified and directed. Note : Colour of tile will be approved by GE.

M&L for 300 x200 x 6 to 7 mm thick glazed ceramic tiles, coloured, in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles, laid over and incl 10 mm thick rendering in CM 1:4, finished even and rough to receive the tiles complete all as specified and directed. Note: Colour and shade of tiles will be approved by GE.

S&F in repairs bib tap, fency type cast copper alloy, with crutch or butterfly handle screwed down for iron pipe or for brass ferrule, of size 15 mm bore complete all as specified and directed.

S&F in repairs stop valve cast copper alloy, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union of size 15 mm bore complete all as specified and directed.

S&F cast iron soil, 75 mm bore, (spun pipe) waste and vent pipes in any length with or without ears, with cement joints, fixed to wall complete all as specified and directed.

S&F cast iron cowl, 75mm complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8, type D2 (using 40 mm graded crushed stone aggregate) as in sub base under floors, finished even and fair to receive top finish complete all as specified and directed.

S&F in repairs vitreous china water closet squatting, Orissa pattern, white, size 580 x 440mm with integral foot rest with cast iron P or S trap including 32mm dia polyethylene flush pipe complete all as specified including provn of lime concrete bedding and connecting to outlet and flush pipe complete all as specified and directed.

S & F in repairs 10 Ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, flush pipe including brackets complete all as specified and directed.

S&F vitreous china wash hand basin, white, flat back size 550 x 400mm with pedestal incl 32mm dia CP waste coupling, 600 mm long 32mm bore HDPE waste down pipe, CI brackets complete all as specified and directed.

S & F 15mm bore steel water tubes, `medium grade', galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S & F 20mm bore steel water tubes, `medium grade', galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Taking down cement or cement lime plaster of any description on brick or stone walls etc incl raking out joints, hacking for key, scrubbing down with water etc in patches at any height complete all as specified and directed

M & L for rendering 10mm thick in CM 1:6 on fair faces of brick work or stone or concrete surfaces, finishing surface even and smooth without using extra cement complete all as specified and directed

M & L for rendering 15mm thick in CM 1:4 on other than fair faces of brick work or concrete surfaces, finishing surface even and smooth without using extra cement mixed with water proofing compound complete all as specified and directed. Note : WPC shall be measured and paid separately.

Taking down shutter n exc 1.00 sqm each and removing from site, making good the dismantled portion complete all as specified and directed.

S&F factory made solid PVC panel door shutter 30mm thick(style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain clour PVC sheets for top rail ,lock rail and bottom rail either side and as gap inserted for top rail and bottom rail .Panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and nails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47 mm, made out of 5mm plain colour PVC sheet, reinforced with MS Square tube supplying and fixing in opening as per specification and drawing complete all as specified and directed

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed. Note:-Colour and shade shade will be approved by GE.

M & L for preparation of newly plastered surfaces of walls etc and applying two coats of weather proof paint over one coat of alkali resistant primer complete all as specified and directed. Note : Tint and shade as approved by GE.

M&L for preparation of newly plastered surface of wall and applying two coats of white wash complete all as specified and directed.

M & L for mild steel framed work such as in grills, framed guard bars, hold fasts, framed doors and gates and similar works, doors drilled to fix sheet, prepared to hanging confirming to Fe-290, Gde-E-165 complete all as specified and directed.

S&F metal welded steel wire fabric n.exc 4 kg per sqm fixed to wood or steel members with welding or rivetting complete all as specified and directed.

S&F Expanded metal, n. exc 4 kg per Sqm, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples complete to wood or steel members, complete all as specified and directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces of any description, over 10Cm width or girth including preparation of new steel or steel based surfaces, complete all as specified and directed.

Excavation in trenches, n. exc. 1.5 m wide and n.exc 1.5 m in depth, for foundation, etc or for shaft, well, cesspit, manhole, pier holes etc.n. exc. 10 sq m on plan and n. exc. 1.5 m in depth and getting out soft/disintregated rock complete all as specified and directed.

M & L for PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation fillings and mass concrete complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, hooking including binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M & L for brick work with old size kiln burnt sub class 'B' bricks, straight or curved on plan exc 6 m in mean radius, built in CM 1:6 complete all as specified and directed.

M & L for PCC 1:2:4 type B1, using 20 mm graded crushed stone aggregate as in surface channels and drains etc including necessary form work and finishing cement concrete surface even and smooth with using extra cement, complete all as specified and directed

M & L sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

M&L for 40mm thick, PCC, 1:2:4, type B2, using 40mm graded crushed stone aggregate as in sub base, sub floors and pavings, etc. complete all as specified and directed.

M&L for 75mm thick, PCC 1:3:6 type C2, using 40mm graded crushed stone aggregate as in sub base, complete all as specified and directed

M&L for 75mm thick, PCC 1:3:6 type C1, using 20mm graded crushed stone aggregate as in plinth protection finish the surface even and smooth without using extra cement, complete all as specified and directed

S&F for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F second class hard-wood clean swan as in scantlings complete all as specified and directed

S&F solid PVC wall lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical type with closed top) of 500 litres capacity, ISI marked, triple layer, marked embosed, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical type with closed top) of 1000 litres capacity, ISI marked, triple layer, marked embosed, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

S&F 20mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

M&L for concrete bed to drain pipes of 100 mm bore, in PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

S&F steel rolling shutter made with 1.25mm thick laths, gear operated type with bevel gear box and crank handle, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed.

M&L for PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate, as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed

M&L for Precast concrete 1:2:4, type B-1, using 20mm graded crushed stone aggregate, as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in CM 1:4 complete all as specified and directed

M&L for 30mm thick bitumen mastic flooring as per IS-13026, complete all as specified and directed.

S & F anodised aluminium frame for doors, windows, ventilators etc with one or more rebates including joining cleat for fixing etc. powder coated (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F 110 mm, PVC (SWR) bends, complete all as specified and directed.

S&F 20mm bore, ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. Minimum weight 2 1 0 g m s, complete all as specified and directed.

S&F 20mm bore, nipple suitable for HDPE water tank Minimum weight 45gms complete all as specified and directed.

S&F 20mm bore, gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Demolition of brick or stone masonary built in cement mortar including all quoins arches pillars etc but excluding ashlars facing dressed stone work and precast concrete block, complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness below or above ground level complete all as specified and directed.

Demolition of reinforced cement concrete in ground floors and pavings n exc 15 cm thickness below or above ground level (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Supply only water proofing compound, as approved complete all as specified and directed.

M&L for rubber moulding machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with gray cement and pigment set over 25mm sand cushioning complete all as specified and directed.

M & L for cutting holes into or through brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime concrete, superficial area exc. 100 sqcm but n exc 250 sq cm and making good in CM 1:4 or PCC 1:2:4 type B-1,complete all as specified and directed.

M & L for mild steel framed work for ornamental and intricate design such as in grills, framed guard bars, hold fasts, framed doors and gates and similar works, doors drilled to fix sheet, prepared to hanging confirming to Fe-290, Gde-E-165 complete all as specified and directed.

S&F 1mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete all as specified and directed.

M/S JASWANT SINGH ANAND

M/S Jaswant Kumar Aggarwal

M/S Meera Builders

M/S J.S.ENTERPRISES