SPECIAL REPAIR OF BLDG NO T-5 UNDER GE (SOUTH) MAMUN AT MAMUN MIL

Amount

Taking down chowkhats or frames of any description not exc 1.50 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware , complete all as specified and directed.

Taking down chowkats or frames of any description exc. 1.50 Sqm and n.exc 4.00 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware , complete all as specified and directed.

Taking down shutter of any description exceeding 1 sqm and not exceeding 2 sqm each including builders hardware etc, complete all as specified and directed.

M&L for 30mm thick "Rajshri / Accucel / Plasopan " brand factory made wire mesh solid PVC door shutter consisting of frame made out of M.S. tube of 19 gauge thickness and size of 19mm x 19mm of stiles and 15 x 15mm for top, lock & bottom rails, MS frames shall have a coat of metal primer of approved make and manufacturer. 19mm x 19mm M.S. square tubes shall be covered with heat moulded plain sheet 'C' channel made from 5mm (+ 0.25) thick PVC sheet of density 600 kg/Cbm manufactured by as ISO 9001-2008 certified company., of size 30mm thickness, 90mm width out of which 75mm shall be flat and 15mm shall be bent in 90° angle on either side forming stile, one of the 90° bent edge is cute from stile as well as rails to nail from inner side of door to hide wiremesh fixing steel screw. 5mm (+0.25) thick 115mm wide PVC sheet out of which 100mm shall be flat and 15mm shall be bent 90° on the inner side to form top and bottom strip of 20mm width is to be stuck on the interior side of the 'C' channel using PVC solvent cement adhesive. Panel will be of GI / SS wire mesh of 24 gauge to be fitted inside area of stiles & rails. The wire mesh in top and bottom & lock rail is sealed with 15mm x 15mm tube with steel wire 13/6 mm. 10mm (5mm x 2Nos) wide cross PVC sheet as gap insert for top rail & bottom rail door to be fixed to frame with 3Nos. M.S. powder coated hinges size 100mm x 20mm x 2mm and 32mm long steel screw drilled suitable to pass through both the walls of the M.S. tube other hardware should be fixed with 19 x 6mm size steel screw, wire mesh double (one of stainless sleel and one of XPM aluminium) complete all as specified and directed.

M&L for 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated, fitted to chowkhats complete all as specified and directed.

M&L for preparation of new wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

M&L for pressed steel frames 125mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for pressed steel frames 105mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for "Rajshri / Accucel / Plasopan " brand factory made PVC door frame (plain) (Chawkhat) - of size 50mm width, 47mm height with a wall thickness of 5mm, made by of extruded 5mm PVC sheet density 600kg/Cbm manufactured by ISO 9001-2008 certified company having pattern width of 50mm and thickness of 10mm. All threeAll three frame length reinforced with 19mm x 19mm MS square tube of 19 gauge. mitre cut at two corner and joining with 2 Nos of 150mm long brackets of 15mm x 15mm MS tube or joint by fusion heat welding. The door frame shall be fixed to the wall using 8/100 mm long MS screws through the frame by using PVC fasterner. A minimum of 4 Nos of screws to be provided for each vertical member & minimum 2Nos for horizontal member complete all as specified and directed & as per manufacturer specification & drawings.

M&L for 250 mm aluminium alloy sliding door bolt with hasp & staple (bolt type) and fixing clip of sheets cast or extruded section and fixing sliding bolt of extruded section complete all as specified and directed.

M&L for Aluminium anodised barrel tower bolt, extruded section 200mm long , complete all as specified and directed.

M&L for Aluminium anodised handle, extruded section of size 100mm complete all as specified and directed.

Preparation of new or previously untreated Steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer all as spd and directed complete all as specified and directed.

M&L for Box type Steel windows and ventilators comprised of tubular frame and shutters made out of 1.25mm thick M S sheet tube factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes only shall be measured and paid separately) with steel handle and steel peg stay dovetailed or welded incl 2 Nos. tower bolts 150mm long for each leaf and 10mm square bar grills at spacing as shown on drg, welded to F I frame work, including other fittings; hinges, handles, tarred hold fasts fixed in PCC blocks all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty or fixed with beads/ glazing pins not .exc 0.5sqm in each pane complete all as specified and directed.

M&L for 3mm thick figured glass, pin head type and glazing with oil putty or fixed with beads/ glazing pins not .exc 0.5sqm in each pane complete all as specified and directed.

M&L for galvanized MS wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple complete all as specified and directed.

Removing old lime wash or colour wall and prepared old unplastered surface of wall to received plaster etc including raking out joints, hacking for key, scrubbing down with water etc all as specified and directed.

Taking down cement plaster on brick walls or stone walls any descrition etc including raking out joints, hacking for key, scrubbing down with water & removal of debris as directed complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges joints free tiles 8mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in skirting/dado/riser of steps etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) including dismantling existing tiles of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises, etc complete all as specified and directed.

M&L for Glazed ceramic (coloured) tiles 7mm thick, of size 450mmx300mm on vertical surfaces such as dado etc, set and jointed in neat cement slurry and pointed in coloured epoxy grout to match tiles over and including 10mm thick backing coat in cement mortar (1:3), surface finished even and rough to receive tiles, including dismantling existing tiles of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises, etc complete all as specified and directed.

M&L for 18-20mm thick machine cut Kota stone slab in single piece in treads etc, set and jointed in neat cement slurry and pointed in coloured epoxy grout to match including rounding the edges and cuttting two grooves (serration) of kota stone over and including 20mm thick screed bed in CM 1:4, surfaces finished even and rough to receive kota stone including dismantling existing tiles/stone of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises, etc complete all as specified and directed. complete all as specified and directed.

M&L for 15-18mm thick machine cut kota stone in skirting to match in size and pattern with kota stone riser and like set and jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 10mm thick backing coat in cement mortar 1:3 (surface finished even and rough to receive kota stone) including rubbing and polishing including dismantling existing tiles/stone of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises, etc complete all as specified and directed. complete all as specified and directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard & railing 60cm long complete all as specified and directed. Make : Cat part No AKS - 35771P of Jaquar or equivalent model in Crabtree/Marc.

S&F in repair for single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Cat part No AQN-7711 of Jaquar or equivalent model in Hindware/Marc.

S&F in repair Brass Chromium Plated shower rose with arms fancy type with swivel joints 75 mm face dia of appoved make and cat part for 15mm bore iron pipes complete all as specified and directed. Make : Prayag Cat part No BS-73 or equivalent model in Hindware/Marc.

S&F 15 mm bore Stop valves/Angle valve cast copper alloy, chromium plated (ISI marked) , screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

S&F in repair for 15mm bore bib taps fancy type with wall flange, chromium plated cast copper alloy long body with capstan heads, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair for PVC connection 15mm size with PTMT nuts of length 450mm long of appoved make complete all as specified and directed.

S&F in repair for Rotational moulded polyethylene water storage tanks three layer of capacity 1000 litre, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm ball valve high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and dismantling of existing PVC tank of any capacity, complete all as specified & directed.

Taking up or down GI water tubing and connections including cleaning for refixing including all new fittings for 15mm bore complete all as specified & as directed.

M&L for GI water tubing surface/concealed, 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Refixing of old steel tubing 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) fixed to wall , floor etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Taking up or down 20mm bore pipe and connections including cleaning for refixing including all new fittings for 15mm bore complete all as specified & as directed.

M&L for GI water tubing surface/concealed, 20mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Refixing of old steel tubing 20 mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) fixed to wall , floor etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Cutting chases not exceeding 10cm in width/girth for concealed water tubing or concealed conduit wiring etc and making good in cement mortar 1:3 to match existing surface etc complete all as specified and directed.

S&F GI pipe 50mm dia medium grade (in short length) as spout pipe laid in brick wall, complete all as specified and directed.

S&F Cast iron Traps ‘P’ or ‘S’ traps 100mm bore complete all as specified and directed.

M&L for rendering or plastering work 10mm thick in CM (1:3) in fascia / edging / ceiling of Chajjas, roof projections and making the line in true shape and finishing the surface without using extra cement, complete all as specified and directed

M&L for Rendering 15mm thick in two layers [base layer 10mm thick in CM (1:6) & finishing layer 5mm thick in cement mortar (1:4)] using liquid water proofing compound on IInd layer on brick work or concrete surfaces of wall, surfaces finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and raking out joints, hacking for key, scrubbing down with water and removal of rubbish, out off the premises, etc complete all as specified & directed. (Note : WPC shall be measured and paid separately)

M&L for rendering 10mm thick on brick work or concrete surface in CM (1:6) on wall surfaces finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and raking out joints, hacking for key, scrubbing down with water and removal of rubbish, out off the premises complete all as specified & directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of distemper oil emulsion (OBD) over a coat of primer as per manufacturer instructions (from same manufacturer of OBD) over a layer of wall care putty 2mm thick complete all as specified and directed.

Complete removal of existing treatment & preparation of plastered surface of walls applying two coats of distemper oil emulsion (OBD) over a coat of primer as per manufacturer instructions (from same manufacturer of OBD) over a layer of wall care putty not less than 2mm thick complete all as specified and directed.

M&L for Preparation of new plastered surface of external wall and chajjas and making the surface smooth with sand paper and priming the surface with primer as per recommendation of manufacturer for external surface, over primed surface and applying two coat of cement base paint complete all as specified & directed.

M&L for preparation of new plastered surfaces of ceiling and apply three coats of white wash on plastered surfaces complete all as specified and directed.

M&L for APP modified roof treatment over existing non-accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification complete all as directed :- (a) Cleaning existing surface properly. (b) Applying oil bound bitumen primer @ 0.30 liter/Sqm manufactured by the same agency as that of APP with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying not less than 3mm thick APP modified water proofing membrane weighing not less than 3.60 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Laying of membrane, Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.60 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gsm/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650/Sqcm and transverse not less than 450/sqcm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Top of membrane shall be provide with solar reflective bituminous aluminum paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane.

M&L for Vitreous china wash hand basin, white, flat back, size 550x400mm (Make : Jaquar Cat part No CNS-WHT-801 or equivalent model in Hindware/Parryware/Somany) including 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated (Make : Jaquar Cat part No FLR-5011N or equivalent model in Hindware/Marc.) brackets, CP waste coupling, (Make : Jaquar cat Pt No ALD 709 or equivalent model in Hindware/Marc) 32mm bore PVC waste pipe of min 600mm long & 15 mm bore PVC connections, including cutting for and pinning in end of brackets or erecting stand fixed in repairs complete all as specified and directed.

S&F for Vitreous china White Squatting Orissa Pattern pan (Make : Somany Cat part No 121115 or equivalent model in Hindware/Parryware) of size 580x440mm, including cast iron ‘P’ or ‘S’ trap, front or back inlet and integral foot rests and making connection to trap and to flushing pipe, anti syphonic pipe, fixed in repair including dismantling existing squatting pan and making good to disturbed floor, complete all as specified and directed.

S&F in repair for Vitreous china white wash down water closet pan (pedestal pattern) with normal closing seat cover S-trap (Make : Jaquar Cat part No CNS-WHT-553SN or equivalent Cat Part/Model of Hindware/Parryware/ Somany) & hand shower (Health foucet) 8mm dia 1m long flex tube in chrome finish and wall hook with NRV (Back flow preventer) and connection to drain (or out going pipe) (Make : Jaquar Cat Part No ALD-577 or equivalent Cat Part/Model of Hindware/Parryware) and to flush pipe, antisyphonic pipe etc complete all as specified and directed

Supply and fix PVC flushing cistern dual flush type 10 Ltr capacity, valve-less syphonic action type, low level, complete with inlet, ball valve, handle, including brackets/pins, PVC flush pipe 32mm bore and PVC connection 15mm bore 450mm long complete all as specified and directed.

S&F in repair 20mm bore gun metal gate valve, with cast iron wheel head, screwed both ends for GI pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butterfly screwed down for GI pipe 20 mm dia complete all as specified and directed.

S&F in repair for 100 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified and directed.

S&F in repair for 75 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified and directed.

S&F in repair for 100 mm bore, cast iron branch pieces or Tee, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access doors complete all as specified and directed.

S&F in repair for 75 mm bore, cast iron branch pieces or Tee, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access doors complete all as specified and directed.

S&F in repair for 100 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with stack clamp made out of 25mm x 3mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair for 75 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with stack clamp made out of 25mm x 3mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair for 50 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with stack clamp made out of 25mm x 3mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair for 100 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with or without ears , fixed to floor cement joint complete all as specified and directed.

S&F in repair for 75 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with or without ears, fixed to floor cement joint complete all as specified and directed.

S&F cast iron cowl for 50mm dia complete all as specified and directed.

S&F in repair for 75 mm Cast iron floor trap, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

M&L broken brick aggregate coarse 40 mm nominal size filled under sunken portion after treatment and compacted to laying floor finising complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregate as leveling course/padding using water proofing compound laid over existing roof, surface finished rough to receive cement mortar including necessary formwork including demolition of existing concrete of any description and removal of debris out off the premises complete all as specified and directed. (WPC shall measured and paid separately)

M&L for rendering 15mm thick on fair faces of roof surface and sunken portion in cm 1:3 finsihed even and smooth (with out using extra cement ) using water proofing admixture complete all as specified & directed. (Note : WPC shall be measured and paid separately)

Supply only Polymer liquid water proofing compound of make Pidilite/Bauchemic/Fosrock, all as specified and directed.

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of existing sheets of any type complete all as speecified and directed. [Note : The colour sheet shall be as approved by GE]

M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick having tensile strength of 550 Mpa as in ridge, fixed with self tapping screws including dismantling of existing sheets of any type complete all as speecified and directed. [Note : The colour sheet shall be as approved by GE]

Dismantling wooden scantling in fillets, rail posts, rafters, purlins etc under 40sq cm in section (framed work) complete all as speecified and directed.

M&L for Suspended false ceiling system using E Grid system Grid size 600mm x 600mm with and including G.I frame work of main runners 38mm x 24mm, cross Tee 28mm x 24mm and wall angle 24mm x 24mm hot diped galvanized steel with zinc coating not less than 120gm/Sqm using 9.5mm thick high tile front side PVC and back side foil paper pressure stream cured fibre cement pre primered disingner board , ISI Marked ISI marked IS-14862 -2000 to be placed in grid of E grid suspended ceiling grid system duly suspended by 4mm dia GI bar hangers from existing purlins to roof with butterfly clips including dismantling of wall and ceiling boards any description complete all as specified and directed. Note :- Invoice from company’s authorized dealer shall be submitted with material by the contractor along with dealership certificate. Certificate of genuineness from the manufacturer shall also be submitted by the contractor before getting the material passed from the department.

M&L for 75mm thick PCC (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in plinth protection laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio (1:2) by weight including dismantling existing floor of any type and pattern and removal of rubbish out off the premises complete all as specified and directed.

S&F factory made 18mm(+ 0.7mm) thick PVC sheet one side prelam sheet for cupboard shutter of density 600kg/Cbm bent 90° and finish at all edges at level for making edges at level for making edge lipping/bending or 0.5mm thick PVC sheet lipping at 4 edges using bonding tape complete all as specified and directed.

S&F continous (Piano) hinges, mild steel,bright finish or elcetrogalvanished size of flap 40mm complete all as specified and directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4) including rounding off exposed edge, complete all as specified and directed.

Cutting holes into brick walls built in cement mortar superficial area n exc 150 sqcmcomplete all as specified and directed.

Cutting opening through brick wall built in cement mortar for exhaust fan and making good disturbed surface with CM (1:3) removing the rubbish to a distance not exc 50mm complete all as specified and directed.

S&F Hasp and staple aluminium anodized 100mm long including bolt to hinge plate and fixed with screws complete all as specified and directed.

Demolition of brick or stone / concrete block/ stone boulder masonry built in cement mortar including all quions, arches, pillars etc but excluding ashlar facings dressed stonework and pre cast concrete articles complete all as specified and directed.

M&L for Brick work with Fly Ash Brick (Non-Modular) Class 7.5, straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and directed.

Labour only (except bricks) for brick work (with serviceable bricks retrieved from dismantling straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and directed. [ Note: Serviceable brick retrieved from Srl. Item No. 82 will be reused for this work]

M&L for Brick work with Fly Ash Brick (Non-Modular) straight or curved on plan to any radius in half brick thick walls built in (1:4) etc including dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, and removal of rubbish out off the premises, complete all as specified and directed.

Demoltion of cement concrete (unreinforced) of any description and in any position not specifically provided for complete all as specified and as directed .

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5mm dia & over but upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, including cranking, bending, spirally for hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 Nominal Mix using 20mm graded crushed stone aggregate as in as in beams, cantilevers, bressummers, lintels and the like including demolition of existing RCC of any type and removal of rubbish out off the premises complete all as specified and directed. [Note: Formwork & reinforcement shall be measured and paid separately]

Form work to sides of soffits and floors or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhanges etc also splays between floors and beams for fair finished concrete surface of concrete complete all as specified and directed.

Form work to chullah hoods, chajjas, toughs & similar items including edges rough finished surface of concrete complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over and including 15mm thick screed base in CM 1:4 as screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and roughening of exisitng concretecomplete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone in skirting/dado to match in size and pattern with kota stone set and jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 10mm thick backing coat in cement mortar 1:3 (surface finished even and rough to receive kota stone) including rubbing and polishing including dismantling existing plastering and removal of debris out off premises etc complete all as specified and directed.

S&F Mild steel powder coated door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate including necessary welding etc complete all as specified and directed.

S&F in repair for Vitreous china Urinal, Half stall type white including 32mmm bore PVC waste pipe, PVC spreader, CP grating, providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screw, pointing around urinal back in coloured epoxy grout to match complete all as specified and directed. (Make : Jaquar Cat part No URS-WHT-13261 or equivalent model in Hindware/Parryware)

S&F in repair 15mm bore Stop valves fancy type, chromium plated cast copper alloy long shank and exposed part kit with fitting sleeve, operarting lever & adjustable wall flange (concealed type) screwed both ends for iron pipe or for unions complete all as specified and directed. Make : Jaquar Cat part No CON-083FT & CON-083FTK or equivalent of Hindware/Marc.

S&F in repair for 25mm bore Mild steel powder coated, single curtain rod (wall thickness not less than 1mm) including fancy type PVC brackets of approved design/pattern, funnels etc suitable for single curtain rod complete all as specified and directed.

M&L for Marble Green/Bhaislana Zebra 18 to 20mm thick (table rubbed and premirror polished) in single piece in steps, jambs, pillars, window-cills, and like set and jointed in neat cement slurry including pointing in epoxy grout to match marble shade, including making hole for gas pipe including rounding the edges of marble stone , laid over and including 15mm thick screed bed in CM 1:4 including dismantling of existing tiles/stone etc complete all as specified and directed.

Dismantling cast iron work of any description complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessoriescomplete all as specified and directed.

S&F 110 mm PVC (SWR) pipes single socketed in any length with rubber joints including bends and necessary fittings complete all as specified and directed.

S&F in repair 110 mm bore, PVC ( SWR) bend complete all as specified and directed.

Dismantling mild steel framed work of hollow pipe joists angle or other section of any description as in roof rafters and purlins, trusses with gusset plates of any descripation complete all as specified and directed.

S&F MS flat of required section in wind ties including fixing with self drilling machine screws on roof sheeting complete all as specified and directed.

Taking down carefully unserviciable/ damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets, Bracket /sketch fitting etc ) and removing material from site and making good to the disturbed surface to match with existing finish complete all as specified and directed.

M&L for Modular Point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box and approved make sunken modular metal flush gang box and suitable support frame and cover plate (inner/outer) of required modules for mounting modular switches/ sockets etc, connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/bell point complete all as specified and directed. (Note : Modular switch/bell push/fan regulator etc shall be measured and paid separately under respective items.)

All as per Srl item No. 106 above but two point controlled by two Nos switch 06 Amp one way, complete all as specified and directed.

All as per Srl item No. 106 above but for 5 pin 5 Amp socket outlet point on independent gang box and suitable support frame and cover plate (inner/outer) controlled by one switch 5Amp one way, etc complete all as specified and directed.

All as per Srl item No. 106 above but for 5 Pin 5 Amp socket outlet point on same board controlled by one switch 5 Amps one way on same gang box support frame and cover plate etc complete all as specified and directed.

All as per Srl item No. 106 above but for one 15Amp socket outlet point concealed using 2.5Sqmm FRLS PVC insulated multi-strand copper conductor wire including 2.5Sqmm FRLS PVC insulated unsheathed copper conductor earth wire and making good to disturbed surfaces of wall floor to match existing finishes complete all as specified and directed.

S&F Modular Socket outlet, 5 pin, multi purpose 2 module 6 Amps, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKSWW065 /Legrand Cat Part No 673452/ Schenider Cat Part No P2005.

S&F Modular Socket outlet, 5 pin, multi purpose, 2 module 6/16 Amp, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKCWW163 Legrand Cat Part No 673455 / Schenider Cat Part No P2106.

S&F Modular Switch 1 way 6/10 Amps , 1 module etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVSXXW101, Legrand Cat Part No 673401, Anchor Roma Cat Par No 289101, Schenider Cat Part No P1001.

S&F Modular Switch 1 way 16 Amps , 1 module etc complete , all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVSXXW161 /Legrand Cat Part No 673411/ Schenider Cat Part No P1101.

S&F Modular Switch 2 way 6/10 Amps , 1 module etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVSXXW101 or equivalent of Legrand/Siemens/Schenider.

S&F Ceiling rose polycarbonate isolated body surface Bakelite, not less than 65 x 50 mm, three terminals, AC 230 volts etc, complete all as specified and directed. Make : Havells Cat Part No Reo/Cona Cat Part No 9246/GM Cat Part No 8224

S & F Fan regulator modular step type suitable for 1200/1400mm sweep ceiling fan hum free, 120W- 2 module including necessary connections complete all as specified and directed. Make : Legrand Cat Part No 673028/Crabtree Cat Part No ACARFHW005/Anchor Roma Cat Part No 66502.

S&F Lamp holder insulated body with back plate suitable for batten fitting including 7 W LED lamp of approved make and cat part and PVC Round/Square block etc complete all as specifeid and directed.

S &F the Bulk head light fitting LED type 10 watt complete with 10 watt LED and having IP-63 protection and fixing on wall/ceiling complete with all accessories and including connecting up with ceiling rose with & including PVC insulated and overall sheathed flexible copper conductor cable and including 3 core 0.50 Sqmm complete all as specified and directed.

M&L for Surface mounted 1x20 watt LED tube light fittings (4 feet long), prewired, decorative luminaire with inbuilt LED tube rod and acrylic end covers with all accessories and PVC Round/Square block for fixing of fittings and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed.

M&L for Surface mounted 1x11 watt LED mirror light fittings , prewired, decorative luminaire with inbuilt LED tube rod and acrylic end covers with all accessories and PVC Round/Square block for fixing of fittings and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed. Notes for Srl Item Nos 119 to 121:- 1. Driver shall be potted antivibration type. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be povided. 3. CRI (Colou Rendring Index) of fixture shall be > 70. 4. CCT (Colout Correlated Temprature of fixture shall be 5700K ± 300 K. 5. System Lumen Efficacy shall be > 100Lm/W 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years gurantee shall be provided by contractor suppoted by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the Contractor shall replace / repair the defective fitting within 07 Days after handing over to Contractor for replacement / repair 11. CA No shall be written on each fitting before installation.

M &L for Double door MCB DB VTPN, 415 Volts, 04 Way made out of CRCA powder coated sheets, IP43 protection with copper bus bar with & incl MCCB TPN 415 volts 63 Amps including taking out old unserviciable MCB DB any size/type, complete all as specified and directed. Make: Legrand Cat Part No 6077-50 or equivalent model in Legrand/Hager/SCHNEIDER

M &L for sheet metal enclosure (Factory made) double door for distribution board (When MCB's are to be used) single pole and neutral 240 Volts 8 way with 200 Amp rated busbar complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole (SP) 240 volts, 6 to 32 Amps, 10KA (C-series) , complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole (SP) 240 volts, 40 to 63 Amps, 10KA (C-series) , complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole neutral (SPN) 240 volts, 40 to 63 Amps, 10KA (C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

M&L for Sub main wiring with FRLS PVC insulated unsheathed 2X6 sqmm multistranded copper conductor cable 1100 V with 1X6 sqmm FRLS PVC insulated green multistranded copper cable for continuous earth drawn through & including concealed PVC conduit of appropriate size not less than 20 mm dia & 1.8mm wall thickness with all accessories including cutting grooves and making good disturbed surface to match existing including taking down existing surface sub main wiring complete all as specified and directed. (Note: Two runs of FRLS PVC cable with one run of earth conductor and conduit shall be measured as one RM.) Make for wiring : Polycab/Anchor/Finolex

M&L for earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, HDPE pipe 15mm bore as protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre is deemed included in unit rate quoted by the contractor. 2. Earth filling shall be done by vegitable soil. 3. Soil shall be free from stone, boulders, aggregate, gravels .

Taking down ceiling fan of any sweep & size and refix in same position after overhauling including minor repairs by replacement of capacitor, safety pin, cap, nuts & bolts etc and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning including application of one coat of synthetic enamel paint by spray painting & rewriting number complete all as specified and directed.

Supply , laying, testing and commissioning for 1100 volt grade XLPE insulated heavy duty cable, 25sqmm 4 core, strip armoured with aluminium stranded conductor overall PVC sheathed laid in trenches including taking down existing cable & bricks complete all as specified and directed. Note : Excavation & Earthwork shall be measured and paid separately.

M & L for sand filling in trenches dry and and clean sand unwashed including punning around cable for protection of under ground cable complete all as specified and directed. [Note : Punned thickness shall be measured and paid]

M & L for well burnt bricks , laid flat ( old size) sub class B designation 75 for cable protection complete all as specifed and directed.

S&F for GI tubing 40 mm bore light grade laid in trenches/floors/ fixed to wall/poles for protection of cable with necessary fittings and FI clamps duly painted complete all as specified and directed.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc (for cable, pole stay manhole etc), in any type of soil and getting out, complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25cm thick, etc complete all as specified and directed.

Removing excavation material n exc. 50m & deposited where directed at a level n exc. 1.5m above the starting point etc complete all as specified and directed.

dadwal engineers

M/s. Nishchal Mahajan

surjit enterprises

M/S J N TRADERS

M/S BHOTO AND CO

M/S DUGGAL CONSTRUCTION CO

Shiva Builders