CONSTRUCTION OF ADDITIONAL GUEST ROOM/SUITE IN THE CAMPUS OF CIRCUIT HOUSE , PATNA (TWO BLOCK G+4).

Earth work in excavation over areas (exceeding 30 cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m; disposal earth to be levelled and neatly dressed. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth : consolidating each deposited layer by ramming and watering lead.

Extra for every additional lift of 1.5m or part thereof in: All kinds of soil

Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.. All kinds of soil

Close timbering over areas including strutting, shoring and packing, cavities (wherever required) etc. complete (Measurements to be taken of the face area timbered): Depth exceeding 1.5 m but not exceeding 3 m

Supplying and filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing designation 100 A one brickedge soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Boring, providing and installing bored cast-in-situ reinforced of grade M-25 of specified diameter and length below the pile cap, to carry a safe cement concrete piles working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc.(By Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap). 600 mm dia piles

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loadingplatform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level. 1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level. 1:3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level. 1:3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in the proportion recommended by the manufactures.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering , finishing and reinforcement-All work puto plinth level.1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping, etc. and removal of form etc. all complete jobs.

Extra for additional height in centring, shuttering where ever required with adequate bracing, propping etc, including cost of de-shutering and de centring at all levels over a height of 3.5 m, for every additional height of 1 meter of part thereof (plan area to be measured) Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Reinforcement to RCC work etc all complete jobs.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M-25 grade with minimum cement content of 330 kg/cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M-25 grade with minimum cement content of 330 kg/cum

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete All work upto plinth level etc all complete jobs.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete Walls, columns, pillars, posts and struts.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete Beams, plinth beams, girder, bressumers, cantilevers, Suspended floors, lintels, roofs and staircase including spiral staircase, shelves etc.

Add or deduct for providing richer or leaner mixes respectively at all floor levels. Proiding M-30 grade R.C.C. instead of M-20 grade R.C.C

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :(1:6) in F/P level etc all complete jobs.

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :Cement mortar 1:4 (1 cement: 4 coarse sand ) etc all complete jobs.

Providing Extra tor Brick work in superstructure above plinth level upto floor V cum etc all complete jobs. 250 mm th Brick work in C.M (1:6), 125 mm th Brick work in C.M (1:4)

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), including ISI marked M.S.pressed butt hinges bright finished of required size with necessery screws, all complete as per directions of Engineer-inCharge and panelling with panels of: 12 mm thick prelaminated (with decorative lamination on one side and balancing lamination on other side) particle board Grade -1 medium density flat pressed, three layer and graded (FPT-1) conforming to IS :3087 bonded with BWP type synthetic resin adhesive as per IS :848 and prelamination conforming to IS :12823 Grade-1 Type II

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - incharge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per direction of Engineer-in- charge. The glass shall be clear, toughened, interlayered, non-wired fire resistant having 11 mm thickness of approved brand with 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 15 min of insulation (EI15) and having a sound reduction of ?37dB and LT of 86%. Glass shall be compliant to class 2(B)2 category of Impact Resistance as per EN 12600. The glass should be manufactured in UL & TUV audited Facility and including UL-EU Certification.The maximum glazing size cannot be more than 1100 mm x 2200 mm (w x h) or 2.42 sq mts in total area. The test report for the complete system (Glazed Door or Partition) will be considered valid only if it contains the stamp and signature of the authorized signatory from the glass manufacturer. (Actual glass size is to be measured at site for payments).

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length.Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal-sash putty of approved make complete including applying a priming coat of approved steel primer; xcluding the cost of metal beading and other fitting except necessary hinges or pivots as required Doors

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer. Using M.S. angle 40x40x6 mm for diagonal braces

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:profile c Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing M.S.fan clamp type I or II of 16 mm dia.M.S. bar bent to shape with hooked ends in R.C.C slabs during laying including painting the exposed portion of loop,all as per standard design complete.

Extra for providing and fixing steel beading of approved shape and section with screws instead of glaxing clips and met. Sash putty in steel doors, windows, Ventilators and comosite units. Steel windows

Steel work welded in built up sections/framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel prime

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.)

"Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as pr IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the erimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding ,other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Providing and fixing oxidised M.S. double acting spring hinges with necessary screws etc. complete 150 mm

Providing designation Fly ash brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l, etc all complete jobs.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete. Size of Tile 60x60 cm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600 x 600 mm.

Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength,thickness & size/shape, made by table vibratory method , to attain superior smooth finish using PU or equivalent moulds, laid in required Grey colour & pattern over 50mm thick compacted bed of coarse sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath,parks,lawns, drive ways or light traffic parking etc. all complete as per manufacturer’s specifications & direction of Engineer -in-Charge:(a) 80 mm thick c.c. paver block of M-35 grade with approved colour design and pattern.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Rajnagar plain white marble /Udaipur green marble/ Zebra block marble Area of slab over 0.50 sqm

Providing and fixing 10 mm thick acid and / or alkali resistant tiles of approved make and colour using acid and / or alkali resisting mortar bedding, and joints filled with acid and / or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in-Charge. In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile.

Extra for Kota stone / sand stone in treads of steps and risers using single up to 1.05 metre.length

Extra for pre finished nosing in treads of steps of Kota stone / sand stone slab.

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having water absorption less than 0.5% and conforming to IS: 15622, of approved make in all colours and shades in outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge 350*0.3*2=210

Providing 12 mm. thick cement plaster in C.M. (1:6) with coarse sand etc. all complete jobs.

Providing 15 mm. thick cement plaster in CM (1:4) with coarse sand etc. all complete jobs.

Providing 15 mm cement plaster on rough side . (1:3) with coarse sand etc. all complete jobs.

Providing 12 mm thick plaster (1:3) with a floating coat of neat cement

Providing 15mm cement plaster 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall

Providing 6 mm. thick cement plaster in C.M. (1:4) in ceiling with coarse sand etc. all complete jobs.

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality. Circular shape 560 mm internal diameter

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal\ size) as per standard design With 20 mm diameter round bar

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Distempering with oil bound washa ble distemper of approved brand and manufacture to give an even shade . New work (two or more coats ) over and including priming coat with cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

With ready mixed red oxide zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shed. Two or more coats on new work

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Stone work (machine cut edge) for wall lining etc. (veneer work ) over 12 mm thick bed of cement lime mortar 1:1:6 (1 cement: 1 lime putty : 6 fine sand ) including pointing in white cement mortar 1:2(1 white cement: 2 stone dust) with an admixture of pigment matching the stone shade: (To be secured to the backing by means of cramps which shall be paid for seperately) Red sand stone- exposed face fine dressed with rough backing 40 mm thick

Extra for plastering walls of height more than 10 m. from ground level for every add it rate height of 3 or part there of etc. all complete jobs.

Extra for plastering : Spherical ceiling

Finishing walls with Premium Acrylic smooth exterior paint with silicone additives of required shade. New work (Two or more coats applied @ 1.43 ltr / 10 sqm. Over and including base coat of water proofing cement paint applied @ 2.20 kg / 10 sqm).

Finishing walls with textured exterior of required shade : New work (Two or more coats applied @ 3.28 ltr/ 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i)1st course of applying cement [email protected]/sqm mixed with water proofing compound conforming tc IS 2645 in recommended proportions. (ii) 2nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii)3rd course of applying blownor/residual bitumen aplied hotat1.7kg. per sqm of area, (iv)4th course of 400 micron thick PVC sheet.(Overlap sat joints of PVC shetshould be100 mm wide and pasted to each other with bitumen @1.7kg/sqni) etc, compete.

Grading roof for water proofing treatment with Cement concrete 1:2:4(1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water -proofing compound cleaning the surface before treatment With average thickness of 120 mm and minimum thickness at khurras point to be 65 .

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Making khurras 45 x 45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1cement:3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of Engineer-in-Charge all complete.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Providing and fixing in true horizontal level Armstrong Cellio Open cell Aluminium lay-in (Grey ) ceiling tiles with border panels forming flush-tegular edge of size 600x600x38mm having Fire Performance CLASS A as per GB 8624-2012. The tile shall be powder coated to White color having powder coat thickness ranging from 60-80 microns. The tile with cell size of 100x100mm shall be laid on Armstrong Suprafine 38 with 15 mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm &amp; 600 mm Cross Tees with a web height of 38mm and a load carrying capacity of 12.5 Kgs/M2 &amp; pull out strength of 100Kgs.The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system of Armstrong make( False ceiling in passage service room waiting looung etc)

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand ) to match the existing floor. With chlorpyriphos / Lindane E.C. 20% with 1% concentration.

Providing well burnt brick bats or Jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/I.

WIRE MESH

Add for plaster drip course/groove in plastered surface or moulding to R.C.C. projections.

Signage

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick bolts and nutts complete Sand cast iron S&S as per IS - 3989

Providing and fixing plain bend of required degree Sand cast iron S&S as per IS : 3989

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts & nuts complete. Sand cast iron S&S as per IS - 3989 100 x 100 x 100 x 100 mm

Providing and fixing single equal plain junction of required degree. 100 x 100 x 75 Sand cast iron S&S as per IS 3989

Providing and fixing single unequal plain junction of required degree.. 100 x 100 x 75 Sand cast iron S&S as per IS 3989

Providing and fixing double equal plain inverted branch of required degree. 100 x 100 x 75 Sand cast iron S&S as per IS 3989

Providing and fixing terminal guard Sand cast iron S&S as per IS - 3989 100 mm

Providing and fixing collar.Sand cast iron S&S as per IS - 3989 100 mm

Providing lead caulked joints to sand cast iron/ centrifugally cast (spun) iron pipes and fittings of diameter 100 mm

Providing and fixing M.S stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diametre. 100 mm

Providing and fixing trap of self cleaning design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors. Sand Cast Iron S&S as per IS: 3989

Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 100 mm diameter pipe

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Providing and fixing on wall face unplasticised PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

Providing and fixing brass stop cock of approved quality :

Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete.

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end).

Providing and fixing gun metal non-return valve of approved quality (screwed end).

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore

Providing and fixing PTMT pillar cock of approved quality and colour 15 mm nominal bore, 125 mm long foam flow, weighing not less than 120 gms

Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid. 150mm nominal size square 100mm diameter of the inner hinged round grating.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy aluminium rod with L.P / H.P.H.D plastic ball. 40mm nominal bore, 206mm long. Weighing not less than 690 gms

Providing and fixing PTMT Soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

Cutting holes up to 30 x 30 cm in walls including making good the same:With common burnt clay F.P.S. (non modular) bricks

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 15 mm nominal dia

Excavating trenches of required width for pipes, cables etc. Including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5M including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering, etc.And disposing of surplus excavated soil as directed within a lead of 50 m Hard/dense soil. Ordinary rock : Pipes, cables etc, exceeding 80mm dia but not exceeding 300 mm dia

Providing, laying Non pressure NP2 class (light duty) RCC Pipes with collars jointed with stiff mixture of cement mortar in the propoertion of 1:2 (1 cement : 2 fine sand) including testing and jointing etc complete .150mm dia RCC pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

Extra for depth for manholes Size 90 x 80 cm

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required : White Vitreous china Orissa Pattern W.C pan of size 580x440mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type)Wall hung WC White matt

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern,with fittings, standard size C.P. brass lush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS :2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C.automatic flushing cistern, with fittings, standard size G.I. / PVCflush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : Range of two squatting plates with 5 litre white P.V.C. automatic flushing cistern.

Providing and fixing white Table top basin of approved make

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required :White glazed fire clay kitchen sink of size 600x450x250 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers comelete.

Providing and fixing toilet paper holder: C P brass

Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm,effective length of tail pipe 260mm from the centre of the waste coupling,77mm breadth with 25mm minimum water seal, weighing not less than 260 gms

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

Providing and fixing soil, waste and vent pipes: 100mm dia Centrifugally cast (spun) iron socket & spigot (S&S) pipe as/IS: 3989

Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc. For 100mm dia pipe

Boring and drilling bore well of required dia for casing/ strainer pipe etc all complete job 300 mm.

Boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer - in-Charge, beyond 90 metre & upto 150 metre depth below ground level. 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges,fittings&accessories etc. all complete, for all depths,as per direction of Engineer -incharge.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

Supplying and filling spreading levelling m stone boulders of size range 5cm to 20 cm in recharge pit etc. Recharge pit - 1x ∏/4x1.2x1.2x0.5=0.56m3 Recharge pit - 1x 0.786x1.24x1.24x0.5=0.604m3

Supplying and filling spreading levelling stone gravel of size range 5mm to 10 mm in recharge pit etc. Recharge pit - 1x 0.786x1.24x1.24x0.5=0.604m3

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. Recharge pit - 1x 0.786x1.24x1.24x0.5=0.604m3

Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 150 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 150 mm dia

inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with mframe (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 455x610 mm and 45 cm deep for single pipe line :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

S/F/F Submersible 1.5H.P pump

Supplying and fixing C.I. cover without frame for manholes :560 mm diameter C.I. over (heavy duty) the weight of the cover to be not less than 108 kg.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.80 mm dia. Nominal bore

Providing and fixing vent pipes :100 mm dia Sand cast iron S&S pipe as per IS : 1729

Providing and fixing in position 25mm diameter mosquito proof coupling of approved municipal design

Providing and fixing C.I. sluice valves (with cap) complete with bolts,nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :100 mm diameter Class I

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

Providing and fixing cast iron dual plate wafer type non return valves of PN1.6 including nuts, bolts,1.5mm thick compressed asbestos gasket including matching flanges as per table "E" complete

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

Providing and fixing brass ball valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/ cm2 of approved quality as specified. 25 mm dia.

Providing and fixing dial type pressure gauge with isolation cock and copper pipe at hydrant station. Dial diameter 100 mm calibration 0-15 kg/ sq.cm.

Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia..

Single headed stainless Gunmetal

Providing and fixing first aid fire hose reel drum wall mounting & swinging type fitted with 20 mm dia 30 m long high pressure hose as per IS : 5132 with 5 mm outlet SS nozzle with shut off valve ( IS: 884-1969). Make :OMEX / NEWTECH / EQV.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :Stainless steel (Grade 304)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless steel (Grade 304

Providing and fixing fire hose cabinet fabricated from 16 gauge M.S. sheet with single glazed front door and pad locking arrangement, painted Fire Red with stove enameled paint and FIRE HOSE written on front including necessary supports ( to house TWO lengths of canvas hose with couplings, branch pipe and nozzle).

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 3 way - 150 mm dia M.S. Pipe Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle,bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 150 mm dia Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm dia

Providing and fixing Carbon-di-oxide fire extinguishers consisting of welded M.S cylindrical body, squeeze lever discharge valve fitted with internal discharge tube, 30cms long high pressure discharge hose, discharge nozzle, suspension bracket, confirming to IS : 15683 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge. Capacity 4.5 kg. ISI Marked.( Contractor should submit test certificate form manufacturer along with serial number of every extinguishers supplied.)

Providing and fixing ABC powder type fire extinguisher with Mono Ammonium Phosphate as extinguishing agent and pressurized with nitrogen as per IS : 15683, ISI marked complete with discharge hose, etc.Capacity 6 Kg.(IS:15683)

Supply & Installation of 5 Kg. Modular Automatic ABC Dry Chemical Powder

Supply & Installation of 22.5 Kg. CO2 Fire Extinguisher (trolley mounted)

AFFF Mechanical Foam Type Fire Extinguisher as Per IS : 15683, ISI marked complete with discharge hose & hanging bracket of 9 Ltrs. Capacity. For Genset.

Supply & Installation of Fire Buckets having 4 buckets and one stand for hanging the four buckets.

Providing and fixing of self illuminated / auto glow "EXIT" signs printed on photoluminescent sheet containing self illuminated base chemical, of appropriate size not less than 400 x 150 mm, suspended from ceiling or fixed to the walls with accessories as required and as directed at site.

Supply, installation, testing and commissioning of Fire Alarm Control Panel with LCD display having capacity of 6-ZONES.

SITC of optical type smoke detectors.

SITC of manual call point in ABS body complete with mounting base.

Supply and Installation of Wall Mounted Horn cum Strobe Lights in ABS body.

Supplying & laying of 2x1.5 sq.mm. ISI marked copper armored conductor cable with gland socket and other wiring accessories on the existing surface/tray/shaft etc as reqd.

Supplying, installation, testing & commisioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, asrequired ( Terrace Pimp ) a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body, bronze impeller, stainless steel shaft, mechanical seal conforming to IS : 1520. b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horizontal foot mounted type with Class - F insulation, conforming to IS - 325. c) M. S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. d) Suitable RC.C Pump-Foundations as per manufacturer's design and 4 nos. Dunlop (cushy foot) heavy duty Antivibration mounting pads. 900 lpm at 35 m Head.

(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft,mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation,conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. Main fire Pump ,Type : Split casting ,Speed (rpm) : 2965,2280 lpm at 70 m Head

Diesel Engine Driven Fire Pumping set suitable for automatic operation consisting of the following as per specifications: a) Horizontally mounted, centrifugal type single stage/ multi-stage fire pump having cast iron body, bronze impeller, stainless steel shaft & capable of delivering 2280 lpm against a total head of 70 m complete with necessary 'Y' strainer on the suction side and pressure gauge with stop cocks etc, on the delivery side including bypass arrangement (with 50 mm dia G.M. stop valve and upto 5M G.I. stop valve and upto 5M G.I. Medium pipes) for periodical testing of the pumping set of the pumping set as per TAC rules b) Water cooled TAC approved Diesel Engine suitable for developing at least 115 BHP at 1800 RPM) for above pump complete with automatic starting mechanism, batteries, automatic battery charger unit, flexible coupling with the pump, coupling with the pump, fuel tank, silencer, exhaust pipe with insulation appro.25m length & all standard accessories as required as per TAC rules including earthing, mandatory spares and tool kit. c) Common bed plate for mounting Pump and Engine fabricated of suitable M.S.Channel as per manufacturer's recommendations. d) Suitable RCC Pump foundations as per manufacturer ' s design 8 Nos Dunlop Anti-vibration (cushy foot) heavy duty mounting pads.

a) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) b) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. c) SuitableHP squirell cage induction motor TEFC type suitablefor operation on 415 volts, 3 phase 50 Hz AC supply with IP55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. d) M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. e) Suitable cement concrete foundation duly plastered and with anti vibration pads.Type : Split casting ,Speed (rpm) : 2965,Capacity : 180 lpm,Head : 70 mtr.,180 lpm at 70 m Head

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required

Supplying & fixing air vessel made of 250 mm dia., 8 mm thick MS sheet, 1200 mm in height with air relaese valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

Providing and fixing heavy duty aluminium armored cables 1.1 KVA grade including necessary support clamps at ceiling

Providing and fixing M.S. structural work fabricated from standard sections, (MS rounds, angles, channels ,slotted angle, etc.) including cutting to size, drilling ,welding or insert plates including cost of (Hilti) fasteners, clamp in RCC structural members as directed, including two or more coats of synthetic enamel paint over one coat of primer after surface preparation including cutting and making good walls.

Supplying & fixing of 150 mm Foot Valve for suction end.

Supply & Installation of Pendant type Sprinkler 15 mm dia. Quartzoid bulb type of rating 68 degree centigrade with required accessories.

Providing and fixing Steel Almirah - Steel Almirah Size 1830H x 900W x 450D with four adjustable shelves, Construction & Material- Prime Quality CRCA** Steel - Panels from 0.6 mm thick (±0.07mm) & Front frame, Shelf 0.8 mm thick (±0.08mm). Full height Steel Hinged Door, Plastic Recessed Handle cum Cam Lock, 3 way locking mechanism with shooting bolt arrangement. The Materials/Organization shall be certified ISO-9001, ISO-14001, ISO-50001, ISO-45001, all ISO Certificates should be Issued from NABCB Accelerated Agency, BIFMA LEVEL 1, BIFMA Membership and BIFMA Compliant product base , Indian Design Mark certified, Trade Mark Certified, GREEN GUARD by UL,GREEN PRO, SEFA, SEDEX, AIOTA, FSC should be Issued from SCS Global Services USA , PEFC, GRIHA & IGBC.

Providing and fixing Visitor Chair - Chair Size (W)590mm X (D)490mm X (H)980mm. Its moulded seat and indented back provide exceptional all-day support. Premium virgin foam sits atop a 14mm thick boiling waterproof plywood forming the moulded seat. This is then encased in deep. The Materials/Organization shall be certified ISO-9001, ISO-14001, ISO-50001, ISO-45001, all ISO Certificates should be Issued from NABCB Accelerated Agency, BIFMA LEVEL 1, BIFMA Membership and BIFMA Compliant product base , Indian Design Mark certified, Trade Mark Certified, GREEN GUARD by UL,GREEN PRO, SEFA, SEDEX, AIOTA, FSC should be Issued from SCS Global Services USA , PEFC, GRIHA & IGBC.

Providing and fixing 3 Seater Sofa Size (W)1905MM X (D)890MM X (H)870MM,Seat Height 400mm. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed. all plywood used in M R Garde and are made by Durian. .The Manufacturer OEM must have ISO-9001-2015, ISO-14001-2015, ISO-45001-2015, ISO-5001-2018 certificates & ISO-13485:2016 issued by NABCB Accelerated Agency, BIFMA Membership Certificate, SEFA, BIFMALevel1/Level 2 Certificate with Screen Shot from BIFMA Website. The Manufacturer/OEM must have indoor Advantage Gold issued by SCS Global Service USA Green Co Certiificate issued by CII.

Providing and fixing 2 Seater Sofa - Size 2 Seater1410MM L X890MM DX 870MM H Seat Height 400mm. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed. all plywood used in M R Garde and are made by Durian. .The Manufacturer OEM must have ISO-9001-2015, ISO-14001-2015, ISO-45001-2015, ISO-5001-2018 certificates & ISO-13485:2016 issued by NABCB Accelerated Agency, BIFMA Membership Certificate, SEFA, BIFMALevel1/Level 2 Certificate with Screen Shot from BIFMA Website. The Manufacturer/OEM must have indoor Advantage Gold issued by SCS Global Service USA Green Co Certiificate issued by CII.

Supply & Installation of Centre Table - Material & Subtype Solid Wood - Beech Wood Table Top Material Clear Glass Frame Material Solid Wood Leg Material Solid Wood Finish Matte Colour & Colour Family Brown -Walnut Dimension (W)1200mm X (D)600mm X (H)460mm Number Of Recliners 1 Number Of Reclining Positions 3 Size Standard Assembly TypeK&nock Down .The Materials/Organization shall be certified ISO-9001, ISO-14001, ISO-50001, ISO-45001, all ISO Certificates should be Issued from NABCB Accelerated Agency, BIFMA LEVEL 1, BIFMA Membership and BIFMA Compliant product base , Indian Design Mark certified, Trade Mark Certified, GREEN GUARD by UL,GREEN PRO, SEFA, SEDEX, AIOTA, FSC should be Issued from SCS Global Services USA , PEFC, GRIHA & IGBC.

SSide Table - Table Size (W)650mm X (D)500mm X (H)460mm. Table Top Thickness 36mm. erching on solid wood trestle legs, the veneer tabletop is tastefully adorned with brick pattern, crafted to perfection by skilled Marquetry artisans. The Materials/Organization shall be certified ISO-9001, ISO-14001, ISO-50001, ISO-45001, all ISO Certificates should be Issued from NABCB Accelerated Agency, BIFMA LEVEL 1, BIFMA Membership and BIFMA Compliant product base , Indian Design Mark certified, Trade Mark Certified, GREEN GUARD by UL,GREEN PRO, SEFA, SEDEX, AIOTA, FSC should be Issued from SCS Global Services USA , PEFC, GRIHA & IGBC.

Supply & InstallationHigh Back Chair - Chair Size (W)580mm X (D)670mm X (H)1255mm. Contemporary Style With A Stately Charm, Bring In The Classy Maestro Office Chair To Suit Your Every Need. Its Classic All-Black Look With Soft Black Fabric Upholstery Makes It An Irresistible Chair. The Deep-Cushioned Back And Seat Conform To The Natural Curvature Of The Spine For Optimum Ergonomics And Lumbar Support. The Synchro-Single Locking Mechanism Along With The Tilt Tension Control, Lets You Find Your Ergonomic Position With Ease. The Pneumatic Height Adjustment Along With The Adjustable Headrest And Adjustable Armrest Further Work To Provide Optimum Ergonomic Comfort. A Strong Chrome Base With A 5-Star Cover Supports The Structure, While The 55Mm Castor Wheels And A 360-Degree Swivel Provide Swift Yet Stable Movement. Get The Maestro Chair And Tackle Your Tasks With Charming Looks And All-Day Support. The Materials/Organization shall be certified ISO-9001, ISO-14001, ISO-50001, ISO-45001, all ISO Certificates should be Issued from NABCB Accelerated Agency, BIFMA LEVEL 1, BIFMA Membership and BIFMA Compliant product base , Indian Design Mark certified, Trade Mark Certified, GREEN GUARD by UL,GREEN PRO, SEFA, SEDEX, AIOTA, FSC should be Issued from SCS Global Services USA , PEFC, GRIHA & IGBC. The mechanism housing should be made up of HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT : Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT: The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY: The pedestal should be High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter. Overall Dimensions of Chair Seat Height -43.1-53.1cm Height -112.7-130.2cm. Width & Depth of Chair as measured from base - Width-76.1 cm and Depth-76.1 cm

Supply & Placing 1 Seater Sofa Size (W)960MM X (D)890MM X (H)870MM. Seat Height 400mm. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed. all plywood used in M R Garde and are made by Durian. The Materials/Organization shall be certified ISO-9001, ISO-14001, ISO-50001, ISO-45001, all ISO Certificates should be Issued from NABCB Accelerated Agency, BIFMA LEVEL 1, BIFMA Membership and BIFMA Compliant product base , Indian Design Mark certified, Trade Mark Certified, GREEN GUARD by UL,GREEN PRO, SEFA, SEDEX, AIOTA, FSC should be Issued from SCS Global Services USA , PEFC, GRIHA & IGBC.

Supply & Installation ofOffice Table with Side Unit Return - Table Top Size (L)2200mm X (D)900mm X (H)755mm and with Side Unit Table Size (2200x1800x750)mm. The Table made of PLPB with matt finish. Made with a combination of engineered wood, this gorgeous desk has contrasting panels in black for a contemporary look. Coupled with a runner and storage for your files and cabinets, the Clint is a desk meant for the discerning tycoon. With a warm walnut finish, the dual tone finish of the desk adds to its overall style and finish. With an option of regular drawers and shuttered glass storage units you can take a pick of which unit suits you the best. The Materials/Organization shall be certified ISO-9001, ISO-14001, ISO-50001, ISO-45001, all ISO Certificates should be Issued from NABCB Accelerated Agency, BIFMA LEVEL 1, BIFMA Membership and BIFMA Compliant product base , Indian Design Mark certified, Trade Mark Certified, GREEN GUARD by UL,GREEN PRO, SEFA, SEDEX, AIOTA, FSC should be Issued from SCS Global Services USA , PEFC, GRIHA & IGBC.

Single Bed Mattress - Mattress Size (W) 915mm X (D) 1980mm X (H) 150mm. our Ortho mattress is ideal for sleepers who prefer complete orthopedic support with a firm yet gentle feel. This single bed mattress feature 5-layer construction that offers targeted comfort and support, all you need for a restful night's sleep. The Materials/Organization shall be certified ISO-9001, ISO-14001, ISO-50001, ISO-45001, all ISO Certificates should be Issued from NABCB Accelerated Agency, BIFMA LEVEL 1, BIFMA Membership and BIFMA Compliant product base , Indian Design Mark certified, Trade Mark Certified, GREEN GUARD by UL,GREEN PRO, SEFA, SEDEX, AIOTA, FSC should be Issued from SCS Global Services USA , PEFC, GRIHA & IGBC.

Pllow-Pillow Size (W) 61 Omm X (D) 406mm X (H) 100mm. Classic pillow strikes a perfect balance betuween soft and supportive,etc. as per direction of Engineer IN Charge.

Bed Sheet- Bed Sheet Size 90cm x 190cm. Best premium quality of make of Bombay Dyeing,etc. as per direction of Engineer IN Charge. First to fourth Floor, SDO Building ,DBO Building

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modular plate, suitable size G.I. box etc as required.

Supplying and fixing suitable size G.I. Box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps. modular socket outlet and 5/6 amps. modular switch, connections etc. As required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. As reqd.

Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/submain wiring along with earth wire with the following size of FRLS PVC insulated copper conducter SC cable in surface / recessed medium class PVC conduit as required.

Supplying and fixing stepped type electronic fan regulator on the existing modular plate/switch box including connections but excluding modular plate etc. As required.

Supplying and fixing 2 pin, 5/6 amps ceiling rose on the existing junction box / wooden block including connection etc as required.

Supplying and fixing batten/angle holder including connection etc as required.

S/F electronic musical call bell suitable for single phase 230 volts complete bell as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 4 nos. 5 pin 5/6 amps modular socket outlet and 4 nos. 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 amps modular socket outlet and 25 amp modular SP MCB 'C' curve, including connections, painting etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box along with modular base and cover plate for modular switches in recess etc as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing recess mounted following types LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing 2'X9 watt LED batten with minimum efficacy 100 lm/w in polycarbonate housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required.

Supplying and fixing 10/12 watt LED type Bulk-head luminaire with minimum efficacy 100 lm/w in comprising of pressure die cast housing, acrylic diffuser,IP 65 protection and complete with integrated electronic driver etc directly on wall/ceiling including connections with 1.5 sq. mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing wall mounted light bracket/ fixture made with polycarbonate suitable for single 9/10 watt LED lamp directly on wall including connections etc as required. ( But without lamp )

Supplying & fixing of following types lamp in the existing electrical fitting/fixtures etc. As reqd.

Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 210 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required.

Supply and fixing of following sweep/ sizes PVC/ABS square body Exhaust Fan with automatic openable louvre shutter in existing opening including making connection, testing etc as required.

Supply and installation of 400 mm, 230 V A.C. wall/cabin fan including fixing the bracket, making connection, testing, commissioning etc as required.

Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required .(but without MCB/RCCB/Isolator)

S/F following rating, 240/415 volts, 'C' curve circuit breaket suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commossioning etc. as reqd.

Supplying & fixing of following types lamp in the existing electrical fitting/fixtures etc. As reqd.

Supplying and fixing following ways, surface/recess mounting, Vertical three phase distribution board ( VTPN DB's ) of CRCA sheet steel, dust protected, duly powder painted suitable for upto 160 amp, four pole MCCB as Incomer and SP/TP MCB's as outgoing inclusive of tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's etc as required. (but without MCCB & MCBs)

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as reqd.

Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following types LED Flood light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Supplying, installation on wall, testing andcommissioning of following capacity Air InsulatedCompact Type Rising Mains for use on 3 phase 4wire 415 volts, 50Hz A.C. supply with enclosurehaving IP-54 rating after fixing the tap off boxes andall accessories, made of 1.6mm thick steel sheet dulypowder coated in convenient sections complete with 4Nos aluminium bus bars having current density of 130A/ sq cm at nominal current rating, necessary joints &expansion joints, fire barrier at each floor, provision oftapping at every metre, continuous earthing with 2Nos aluminium strip of suitable size (one on eachside) including, G.I. clamping brackets, angle ironbracket, steel fasteners, connecting to earthingsystem etc. as required.

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Sandwich Type rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required.

Supplying, installation, testing & commissioning offollowing capacity Plug In/ tap off box on the existingAir Insulated Compact Type bus trunking/ risingmains for use on 3 phase 4 wire 415 volts, 50Hz A.C.supply made with 1.6mm thick sheet steel enclosure(IP54) duly powder coated with provision ofMCCB/ACB (but without MCCB/ACB) complete etc.as required

P/F following capacity rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubical panel board including drilling holes in cubical panel, making connections etc. as required.

Providing and fixing following capacity four pole ON-load/ panel mounted changeover switches inside the existing cubical panel board including drilling holes in cubicle panel, making connections etc. as required.

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as reqd.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing & fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required.

P/F following capacity rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubical panel board including drilling holes in cubical panel, making connections etc. as required.

Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears etc.

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Supplying of copper strip of all sizes for busbar strip/ interconnection including drilling holes etc as reqd.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing & fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required.

Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Jointing copper/ G.I. tape ( with another copper/ G I tape, base of the finial or any other metallic object ) by riverting/ nut bolting sweating and soldering etc. as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of tinned G.I. bolts, nuts, chuk nuts and spring washers etc. complete as required.

Earthing with G.I. earth pipe 4.5 mtr long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. With charcoal and salt as required.

Providing and fixing 25 mmX 5 mm G.I. strip on surface or in recess for connection etc. as required.

Supplying and fixing following size/ modules, GI box along with modular base and cover plate for modular switches in recess etc as required.

Supplying, Installation, Testing & Commisioning of 3 Mtrs long factory made CAT6A UTP RJ 45 patch cord ( Make - Legrand/D-Link/Molex )

Supplying, Installation, Testing & Commisioning of 1 Mtrs long factory made CAT6A UTP RJ 45 patch cord ( Make - Legrand/D-Link/Molex )

S/Fof I/O Module with Face Plate with Copper Earth Tape ( Make - Molex/D-Link )

Supplying fitting fixing 9U Network Rack CRCA 'D' Grade thickness (mm) 1.2, RAL 9017 (Matt Black). Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230VA/C 90 CFM)-2 Nos, PDU 230VAC - 1 No. Cable Manager Metai. 1 No, Mounting Hardware (20 sets of M6 screws,washer,cage nuts (nickel coated)) 1 No, Wall Screws (4 sets of 2" screws,washer,rubber grommet (nickel coated)) 1 No, Door Lock 1 No. Front Metal Band -1 No. In the rack there must be maintained 1 U = 1.75 inches space. complete etc as required. (Make - Legrand/ Netrack/ Rittal)

Supplying Fitting fixing Cat6a U/UTP 24 Port 19" Modular Type Paech Panel Loded with 48x Toolless RJ 45 which is 6 in a block complete etc as required. ( Make - CommScope )

Supply, Installation, Testing & Commissioning of Cisco Business CBS350-24T-4G Managed Switch | 24 Port GE | 4x1G SFP+ | Limited Lifetime Protection (CBS350-24T-4G) SWITCH PORTS: 24 -Port 10/100/1000 + 4 x 1GE SFP+ENHANCED SECURITY: IP-MAC port biding detects and blocks deliberate network attacks. IPv6 First Hop Security provides unparalleled protection against a vast range of address spoofing and man-in-the-middle attacks on IPv6 networks INNOVATIVE DESIGN: Elegant and compact design, ideal for installation outside of wiring closet such as retail stores, open plan offices, and classrooms ( Make - CISCO )

Supplying and drawing of UTP 4 pair CAT 6A LAN cable in the existing surface/ recessed PVC conduit as required.

Metre

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of tooless RJ 45 information for CAT6A U/UTP white colour Arteor Modules 1 along with built in crimping handfree min 5 times reconnection possible and shutter protection etc as required. ( Make - Legrand/Honeywell/ Eqv. )

Supplying and fixing following size/ modules, GI box along with modular base and cover plate for modular switches in recess etc as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and drawing following pair 0.5 sq. mm FR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/ recessed PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

SITC of 4 MP IR Bullet Fixed lens Camera -1/2.8"ProgressiveScan CMOS, 1920 × 1080 at 25fps, 0.01 Lux at F1.2, 0 Lux withIR, ICR, ONVIF (PROFILE S), support H.265, H.264, MJPEG,DWDR, 3D Digital Noise Reduction, Three individuallyconfigurable stream, 12 VDC & PoE, IR range: 40m, IP67, EdgeAnlalytics- Line crossing detection, Intrusion detection, Motiondetection, Scene change detection, Video tampering, UL, CE,FCC certified. (Approved Makes: Hikvision/ Honeywell/Bosch/Panasonic)

SITC of 4 MP IR Bullet Fixed lens Camera -1/2.8"ProgressiveScan CMOS, 1920 × 1080 at 25fps, 0.01 Lux at F1.2, 0 Lux withIR, ICR, ONVIF (PROFILE S), support H.265, H.264, MJPEG,DWDR, 3D Digital Noise Reduction, Three individuallyconfigurable stream, 12 VDC & PoE, IR range: 40m, IP67, EdgeAnlalytics- Line crossing detection, Intrusion detection, Motiondetection, Scene change detection, Video tampering, UL, CE,FCC certified. (Approved Makes: Hikvision/ Honeywell/Bosch/Panasonic)

SITC of 4 MP PTZ Camera1/2" sensor with 31x optical zoomForensic WDR, Lightfinder, and OptimizedIRNext-generation AI-powered analyticsAxis Zipstream with AV1, H.264, H.265Built-in cybersecurity with Axis Edge Vault, LightfinderLightfinder 2.0, Min illumination/ light sensitivity (Color) 0.06lux, Min illumination/ light sensitivity (B/W) 0.001 lux, Imagesensor CMOS, Image sensor size 1/1.7", Wide dynamic rangeForensic WDRPan, Tilt, ZoomProperty description Property value Optical zoom 31Pan range 360 endless Tilt range +20 to -90Guard tour preset position tour Digital zoom 12. (ApprovedMakes: Hikvision/ Honeywell/ Bosch/Panasonic)

SITC of 32ch Network Video Recorder - Connect Up to 64 IPCameras, Dual OS, Up to 12 Megapixels Resolution, Twoindependent HDMI outputs, one HDMI output of 4Kresolution,1 VGA output with output upto 1920 × 1080, SupportH.265, MJPEG, Supports N+1 hot spare system,Supports RAID0,RAID1, RAID5, RAID6 and RAID10 ,Supports HDD hot swap,Supports Dual Power-Redundant, Incoming Bandwidth 320Mbps, 8 SATA Hard Disks, ANR Technology, 8 SATA interfacesfor 8 HDDs and capacity of each HDD upto 6TB, 3 × USB at least1 × USB with 3.0, Alarm I/O 16/4, RS-485, RS-232, 2 RJ-45 10/100/1000 Mbps self-adaptive Ethernet interface, Multiplenetwork monitoring: Web viewer, CE, FCC, UL certified.(Approved Makes: Hikvision/ Honeywell/ Bosch/Panasonic)

SITC of 6TB Surveillance Hard Disk Custom-built for surveillanceapplications with Image Perfect firmware for crisp, clear, 24×7video workloadsMaximum 180TB/year workload rating—3× the workload ratingof desktop drives—for reliable performance in write-intensivesurveillance systems Rotational vibration (RV) sensors helpmaintain performance in RAID and multi-drive systems (4TB orhigher) Up to 10TB of capacity to store up to 10,000 hours of HDvideo (Approved Makes:Seagate/WD/Toshiba)

SITC of SWITCH PORTS: 24-Port POE 10/100/1000 + 2 x 1GEcopper/SFP combo. Fixed-configuration 1RU x 1/2, half-rackwidth chassis24 x RJ45 10/100/1000 BaseT PoE+ ports2 x SFP/RJ45 combo ports2 x SFP ports1 x USB port (type A, USB 2.0)1 x Console port (RS232 RJ45)IEEE 1588v2 capable ports 12MACsec capable ports 12Switch capacity 24 Gb/sPoE power budget 115WIncludes power cord & manuals/software access cardsIncludes RJ45 to DB9 adaptorOperating temperature: -10°C to 60°C (14°F to 140°F)Storage temperature -40°C to 85°C (-40°F to 185°F)(Approved Makes: Cisco/Alcatel/HP/Dlink)

SITC OF 43” Professional display rated for 24/7 operation withessential professional functionsScreen Size 43Brightness (cd/m²) 350Contrast Ratio 1200:1Dynamic ContrastRatio 400,000:1Response Time (ms) 8.0Display Resolution (H x V, pixels) 3840 x 2160HDR (High Dynamic Range)compatibility Yes (HDR10, HLG) MAKE -PANASONIC/SONY/SAMSUNG

Supplying and drawing of UTP 4 pair CAT 6A LAN cable in the existing surface/ recessed PVC conduit as required.

Metre

Supply , Installation , Testing and Commissioning of 15U(600W/1000D) floor mount rack with fans , 2 cable managers ,satationary shelf , 2 Nos. of hardware pkts.Approved Makes: Netrack/MTS/Rittal/APC/APW

Supply , Installation , Testing and Commissioning of 04U(600W/1000D) floor mount rack with fans , 2 cable managers ,satationary shelf , 2 Nos. of hardware pkts.Approved Makes: Netrack/MTS/Rittal/APC/APW

Supply , Installation , Testing and Commissioning of CAT6Ainformation outlet (I/O) for Data, Voice, Camera & Wi-Fi at userend Approved Makes: Belden/Siemon/Dlink/Legrand

Supply , Installation , Testing and Commissioning of loaded 24port CAT6A jack panel for CAT6A cable termination at rack end.Approved Makes: Belden/Siemon/Dlink/Legrand

Supply , Installation , Testing and Commissioning of CAT6Apatch cord 3 feet for rack side switch to jack panel connectivity.Approved Makes: Belden/Siemon/Dlink/Legrand

Supply , Installation , Testing and Commissioning of CAT6Apatch cord 7 feet for information outlet (I/O) to end userdevice connectivity. Approved Makes: Belden/Siemon/Dlink/Legrand

Supply , Installation , Testing and Commissioning of 1, 2 and 4port face plate white for I/O fixing at user side.Approved Makes: Belden/Siemon/Dlink/Legrand

SITC of PVC box for camera mounting. Make -Finolex/malhotra/Anchor

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

SITC of 5 Mtrs HDMI CableCable Type HDMI with Ethernet 10.2 Gbps SpeedConnector 1 USB Type AConnector 2 HDMIConnector Material Gold PlatedCable FlatEthernet Channel HDMIModel High Speed with Ethernet 5 MtrCompatible Devices Gaming Console, TV, Computer, Camera,Color Black, Suitable For Mobile, Laptop, Tablet, Mp3, GamingDevice, Cable Length 5 m. Make - Honeywell, Kramer, Eqv

h) DC Distribution Board And AC Distribution Panel Board: IP65, free standing, metal cladded, having copper bus bar, having required protection and control gears, connection-interconnection, etc. as required.

Supplying, installation, testing and commissioning of microprocessor based intelligent addressable main fire alarmpanel, central processing unit with the following loopmodules and capable of supporting not less than 240devices (including detectors) and minimum 120 detectors perloop and loop length up to 2 km, network communicationcard, minimum 320 character graphics/ LCD display withtouch screen or other keypad and minimum 4000 eventshistory log in the non volatile memory (EPROM), powersupply unit (230 ± 5 % V, 50 hz), 48 hrs back-up with 24 voltsealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout logand facility to have seamless integration with analog/digitalvoice evacuation system (which is part of the schedule ofwork under SH: PA System) and shall be complete with allaccessories . The panel shall be compatible for IBMS systemwith open protocol BACnet/ Modbus over IP complete as per

Supplying, installation, testing & commissioning of centralgraphical fire alarm management system to centrally monitorand operate the fire alarm system complete as required.

Supplying, installation, testing & commissioning of intelligentanalog addressable photothermal detector complete withmounting base complete as required.

Supplying, installation, testing & commissioning of responseindicator on surface/recessed MS Box having two LED,metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of faultisolator complete with base as required.

Supplying, installation, testing & commissioning of intelligentaddressable thermal detector with rate of rise cum fixedtemperature thermistor complete with base as required.

Supplying, installation, testing & commissioning ofaddressable fire control module complete as required.

Supplying, installation, testing & commissioning ofaddressable manual call point complete as required.

Supplying, installation, testing & commissioning ofaddressable horn cum strobe complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable,600/1000V rated with annealed copper conductor havingXLPE insulation, steel wire armouring & FRLS/HFFR outersheath complete as required.

Supply, installation, testing, commissioning, and final testing of automatic lift complete in the shaft well and pit already constructed as per CPWD specification including automatic rescue device (ARD). All standard equipments, accessories and control equipments as per manufacturer's design and as per CPWD specification (Part III LIFTS) on turnkey basis. Conforming to NBC/statutory norms and fulfilling following requirements

P/Year

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

Fixing for laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Providing chemical/ mineral maintenance free aerthing system comprising of copper earth electrode 3 metre length and 17.2 mm outer dia along with 25 Kg earth electrode conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth inspection pit etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required.

VRV/VRF outdoor AC unit:- Supply installation testing and commissioning of VRV /VRF /MRV outdoor units with following multiple inverter based scroll type compressors, electronic expansion valve, R 410A/ecofriendly green refrigerant, cooling & heating mode both options, special pre-coated fin type heat exchanger, low noise direct driven propeller condenser fans in each module with top discharge including internal wiring, microprocessor controls, safety. The condensing unit should be capable of providing cooling between +/- 5deg. C. to 48 deg. C & heating within 0 deg. C to 15 deg. C, COP not less than 3.3. complete as per specification. Outdoor/indoor units should be of same make (brand). (Single phase/three phase)

VRF/VRV indoor AC unit (wall mounted):- Supply installation testing and commissioning of wall mounted indoor split unit comprising of copper evaporator, electronic expansion valve, blower, motor, filter pad, auto air swing louvers, and temperature & on/off display with provision of discharge angle setting by wireless remote controller including internal wiring, controls complete as per specification. (Single phase/three phase)

VRF/VRV indoor AC unit (ceiling mounted 4 way):- Supply installation testing and commissioning of 4 way round flow ceiling suspended/mounted cassette type unit comprising of copper evaporator, electronic expansion valve, blower, motor, filter pad, auto air swing louvers, temperature &on/off display with inbuilt drain pump & decorative panels including internal wiring, controls. Dimension in terms of length & width should not be more than 950mmX950mm with wireless remote controller. (Single phase/three phase)

Refrigerant:- Supply and additional refrigerant charge of refrigerant R410/410A & equivalent Eco friendly green gas to compensate the additional piping done at site for all systems including testing commissioning as required.

Drain piping :- Providing and fixing of CPVC, 6Kg/cm2 drain water piping with fittings, support and insulated with 6 mm thick closed cell elastomeric nitrile rubber insulation complete as per specification.

Copper piping: - Supply, installation, testing and commissioning of interconnecting copper refrigerant pipe work (19mm/13mm thick) duly insulated with elastomeric nitrile rubber type tubular insulation between indoor & outdoor units as per specifications. And exposed piping should be wrapped with glass woven cloth and lag coating for vapour barrier and weather protection. Joints shall be covered with nitrile rubber tape of 3 mm thick complete as per specification.

Y joints:- Supply, installation, testing & commissioning of ref nut/Y-joints brass for indoor and outdoor units of suitable size as per requirement,

Control cable: - Supply and laying, testing & commissioning of following sizes of shielded copper conductor Communication cables on existing tray including fixing clamps & proper connections to equipment etc. complete as required.

Meter

Outdoor stand fabrication :- Supply, fabrication and erection of angle/channel/flat iron stand, hanging arrangement for air conditioning machines & ducts etc, back /support clamps or other similar work etc. including nut bolts of required size, making holes, fabrication, welding, cutting, etc. and painting with one coat of red oxide paint & two coat of enamel paint as required as per specification.

AIR FILTERATION : Purifying Panel for Cassette indoors to keep the indoor air fresh & clean. The 4way cassette Panel should consist of 2 types of filters - a prefilter and PM1.0 filter. The PM1.0 Filter and Pre-Filter should be washable and reusable type. So that customer can continue enjoying clean, fresh air, while also saving on maintenance costs, as no new purification filters are to be bought. The PM1.0 filters should be able to sterlize up to 99% of the microorganisms that are collected on the filters. The filters shall be certified by Intertek & same shall be mentioned in the catalog of the OEM

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Main Distribution Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing floor /wall mounted, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying & fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc as reqd.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and laying in position cement concrete 1: 3: 6 (1 : cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc. as required. (for Sub-Station Foundation)