CREATION OF HIGH EXPLOSIVE TEST CENTER (HETC) AT HEMRL PUNE

Amount

SUBHEAD- I- SITE DEVELOPMENT

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

SUBHEAD - II EARTH WORK AND EXCAVATION

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

Ordinary rock

Hard rock (blasting prohibited)

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 1Km and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto1Km and lift upto 1.5 m, as directed by Engineer-incharge.

Ordinary rock

Hard rock (blasting prohibited)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 1km and lift upto 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

All kinds of soil

Ordinary or hard rock

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete

Extra for levelling & neatly dressing of disposed soil completely as directed by Engineer-in-charge.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for Pre & Post -CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Treatment of soil under floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor. With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

SUBHEAD- III PLAIN AND REINFORCED CEMENT CONCRETE WORK.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Extra for providing and mixing water proofing material in cement concrete work @ 1 kg per 50kg of cement.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.

Extra for addition of synthetic Polyester triangular fibre of length 12mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 in cement concrete/RCC/Flooring/water retaining structures by using 125gms of synthetic Polyester triangular fibre for 50 Kg cement used as per directions of Engineer-in-Charge.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all height & level.. Thermo-Mechanically Treated bars. Fe-500D

Centering and shuttering including strutting, propping etc. and removal of form for . Design of Shuttering will be approved by engineer in charge.

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Extra for shuttering in circular work (20% of respective centering and shuttering items)

Edges of slabs and breaks in floors and walls Under 20 cm wide

Weather shade, Chajjas, corbels etc., including edges

Modular formwork : Centering and shuttering including strutting, propping etc. and removal of form for walls of any thickness, level and height / depth etc. complete using modular form work of approved make for Retainning wall / slab etc. all complete as per directed by Engineer-in-charge. The surface shall be exposed and no plaster shall be done over the RCC surface.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

SUBHEAD - IV BRICK MASONRY WORK .

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar of thickness specified by manufacturer all complete as per direction of Engineerin- Charge. ( RCC band and reinforcement all including ).

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. Cement mortar 1:6 (1 cement : 6 coarse sand)

Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : Flush/ Ruled pointing

SUBHEAD - V : PLASTERING AND SURFACE TREATMENT

Providing of 6mm cement plaster of mix in all surface with cement mortar 1:3 (1 cement : 3 fine sand) at all levels

Providing of 12 mm cement plaster of mix in all surface with cement mortar 1:6 (1 cement : 6 fine sand) at all levels.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers:

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing GI plaster mesh of nominal thickness 0.35 to 0.40 mm with zinc coating of 120 gms per sq m of all as directed.

SUBHEAD - VI : FLOORING

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and polished machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 Cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment. epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all level Granite of any colour and shade Area of slab over 0.50sqm

Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work / Marble Work

Extra for fixing marble / granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with expoxy resin based adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size

Size of Tile 600X600 mm.

Size of Tile 1000 x 1000 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Double charge vitrified tile polished finish of any size

SUBHEAD -VII : DOOR WINDOW & WOOD WORK

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile C Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality . 1.0 mm thick

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete. 2nd class teak wood 50x12 mm

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of Approved Quality)

Supplying, fitting and fixing fully glazed steel windows and ventilators of approved manufacture in single or composite units, both openable and fixied type as per IS:1038 and IS:1361 with all joints finished and butt welded including providing mullions, using 6 mm thick wired glass fixed with aluminium beading and PVC gaskets etc complete with steel oxidised handles and peg stays as specified and approved, and a shop coat of primer.

a) Openable side hung glazed shutters

b) Fixed glazed panels

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: a) 125 mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper

Providing and fixing of rubber nylon door buffer (dia of 40mm and 50mm long) on wall with rowl plug and screw.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Providing and fixing to existing door frames. 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.

SUBHEAD -VIII : STEEL WORK

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube

SUBHEAD - IX : ROOFING & WATER PROOFING

Providing and fixing on wall face unplasticised Rigid Single socketed PVC rain water pipes conforming to IS : 13592 Type A, along with injection moulded fittings as required e.g., bends on any angle, sockets, junction, cowls, offsets, access pieces, including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, providing and fixing MS stays & clamps and cutting & making good the holes in floors and walls wherever required etc. all complete. (For Rain water pipe). a) 110 mm diameter

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diametre and weighing not less than 440 grams.

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete :Serrated with central bulb (225 mm wide, 8-11 mm thick)

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS:2645 and approved by Engineer - in- charge over the RCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment.

Laying cement concrete using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer - in- charge over 20mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to IS2645 and approved by Engineer - in- charge to required slope and treating similarly the adjoining walls up to 300 mm height including rounding of junctions of walls and slabs. After two days of proper curing applying a second coat of cement slurry admixed with proprietary water proofing compound conforming to IS:2645 and approved by Engineer - in- charge .

Finishing the surface with 20 mm thick joint less cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS:2645 and approved by Engineer - in- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making of 300x300 mm square 3mm deep. The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge. a) With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Supplying and fixing of precoated Zincalume/Galvalume sheet roofing of 0.5mm TCT -AZ-150, 550 mpa (Alumunium Zinc Alloy couting of 150 gms, per sqm total on both sides) as per AS: 1397 in cover width of 1000-1020 mm, (size, shape and pitch of corrugation as approved by Engineer-in-charge).The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap.The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness (BMT), Hi-strength steel with min. 550 MPa yield strength.The raw material shall be of Tata BlueScope ,Kirby .The steel sheet shall be fastened with 25 μm zinc-tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners of approved make with EPDM washer as per the requirement considering the profile shape and design load.Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportaion and should be suppplied in single length upto 12meter or as directed by Engineer-in-charge.

SUBHEAD - X SANITARY INSTALLATIONS

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Supplying and fixing approved quality European water closet with FRP cistern set comprising of : ( a ) Star White glazed European water closet with wash down pattern of approved make with P or S trap fixed to floor with necessary teak wood plugs, CP brass screws, etc. ( b ) 10 ltrs. capacity PVC low level flushing cistern made of corrosive resistant materials fixed to wall with necessary brackets and screws, and plugs with matching chromium plated flush bend with float valve and flushing arrangements of slimline or equivalent. ( c ) 15 mm heavy quality flexible PVC inlet connection with brass hexagonal check nuts with washer at both ends. ( d ) Approved make plastic seat and cover (Commander or equivalent make) to match the colour of water closet and CP hinges fixed to water closet. ( e ) 15 mm CP brass Angular stop cock fixed between GI outlet and PVC inlet. Hindware Cat No. 20012 or equivalent.

Providing and fixing wash basin with CI brackets,32mm CP brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever required. W.B Hindware model 10080 /Parryware or Equivalent White vitreous china wash basin(round/oval under counter) size 580 mm x 430 mm with 15mm C.P. brass pillar tap Jaguar Model No CON-359KN & Bottle trap-Jaquar model no. ALD 769/CERA or approved equivalent, 15mm PVC connection pipe with angle valve and CP waste-Jaquar model no. ALD 709/CERA orapproved equivalent).

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar tap Jaguar Model No CON-123BKN, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require with White vitreous china flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap, 15mm PVC connection pipe with angle valve , waste coupling & 2 CI brackets (Parryware indus C0471 (CTH)/72 (SP) or equivalent).

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with fittings, standard size C.P. brass flush pipe, CP Angle stop cock along with Urinal Spreader, 32mm dia waste fitting,waste pipe, including cutting and making good the walls and floors wherever required : Urinal : Hindware Cat No. 96007 or equivalent.

Providing and fixing 16mm thick stone slab with table rubbed, edges rounded and polished, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. in Granite Stone of approved shade

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. With Flexible pipe 32 mm dia

Providing and fixing beveled edge mirror of superior glass of approved quality complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing soap dish of approved quality including fixing with C.P. brass screws etc. complete. (Jaquar CAT NO - ACN - 1131N)

Providing and fixing C.P. Brass towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality colour and make. 600mm x 20mm size (Jaquar CAT NO - ACN - 1111N)

Providing and fixing C.P. Brass towel ring 200 dia size complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality colour and make. (Jaquar Cat No. ACN - 1121NR)

Providing and fixing C.P. brass toilet paper holder with concealed fitting arrangement of approved quality colour and make. (Jaquar Cat No. ACN - 1151N)

Providing and fixing Health faucet with concealed fitting arrangement of approved quality colour and make. (Jaquar ALD-565)

Providing and fixing approved type SS Double coat hooks with concealed type screws. Jaquar 1161 or equivalent approved make.

Providing and fixing 15 mm nominal bore C.P. brass short body two way bib cock 15 mm nominal bore - Jaquar cat no-23041 N/equivalent .

Providing and fixing C.P.brass long body bib cock of approved quality conforming to IS standard and Weighing not less than 690 gms. (Jaquar model no. CON-107kn/approved equivalent). 15 mm nominal bore.

Providing & fixing in position CP Soap dispenser.(Jaquar model no. ACN- 1135/approved equivalent).

SUBHEAD - XI - INTERNAL WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing this includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-charge. Concealed work, including cutting chases and making good the walls etc.

a) 15 mm nominal dia Pipes

b) 20 mm nominal dia Pipes

c) 25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

25 mm nominal outer dia Pipes

32mm nominal outer dia Pipes

40mm nominal outer dia Pipes

50mm nominal outer dia Pipes

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 15 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.

a) 20 mm dia

b) 25 mm dia

c) 32 mm dia

Providing and fixing Butterfly valve (upto 150mm dia with band lever operation & above with gear box operation) with SS-304 disc. Tested to a pressure not less than 15 Kg/sq.cm including rubber gaskets, flanges, nuts, bolts, washers & painting complete as required.

a) 65 mm dia

b) 80 mm dia

Providing and fixing unplasticised P.V.C connection pipe with PTMT Nuts coller and bush of approved quality and colour. With 15mm nominal bore with 45cm length

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

(a) 500 Ltrs

(b) 1000 Ltrs

Providing and fixing Storage type Water Cooler with inbuilt RO water purification system including necessary inlet/outlets, CP angle stop cock & making drain connection etc. complete including all required fittings as required. Purified water production capacity - 60 LPH, Storage capacity -60 LPH

SUBHEAD - XII - EXTERNAL WATER SUPPLY

Supply erection testing and commissioning in position the following heavy class G.I. pipes conforming to IS:1239 cut to required lengths including all necessary fittings (conforming to IS:1879) and specials such as bends, tees, unions, reducers, flanges & plugs etc. fixing at wall/ceiling level supported by clamps, hangers etc,cutting hole in wall/floor/slab and making good the same good with cement concrete 1:2:4 / fire sealant complete as required.

a) 32 mm dia

b) 40 mm dia

c) 50 mm dia

d) 65 mm dia

e) 80 mm dia

Supply, installation, testing and commissioning of tanker inlet connection complete with 80 mm dia GI inlet piping, hose inlet connection, M.S. cabinet enclosure (epoxy painted after fabrication), pad locking arrangement, inlet flexible hose complete with all necessary arrangement.

Supply, installation, testing and commissioning of CI Butter fly valve of class PN 1.0 suitable for fixing between two flanges, including bolts, nuts, rubber insertions complete and of following sizes etc complete.

a) 50 mm dia

b) 65 mm dia

c) 80 mm dia

Supply, installation, testing and commissioning of C.I. dual plate type check valve tested to a pressure of 15Kg/sqcm. Including rubber gasket, flanges, union, nuts, bolts, washers & painting complete as required.

a) 50 mm dia

b) 65 mm dia

c) 80 mm dia

Constructing masonry chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants, with C.I. surface box 350x350 mm top and 165 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand :10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design. With common burnt clay F.P.S. (non modular ) bricks of class designation 7.5.

SUBHEAD - XIII - SEWERAGE DISPOSAL INTERNAL AND EXTERNAL

Internal Drainage

Providing, fixing and jointing UV stabilized SWR (Type - B) pipes conforming to IS:13592 including all fittings such as bends, clamps, tees, cowls, clean out plugs, offsets, Y-tees, tees, door fittings, clips, clamps, stays etc. conforming to IS-14735, including jointing with rubber gasket fixing in sunk areas, Fixing at wall / ceiling level supported by steel clamps & hangers etc. including Cutting, chases/ holes in floors / walls / slab and making good the same after pipe have been duly laid and testing complete in all respects.

a) 75 mm dia.

b) 110 mm dia.

Providing, fixing,and jointing UV stabilized SWR (Type - B) pipes conforming to IS:13592 including all fittings such as bends as required lengths including all necessary fittings (conforming to IS:1879) and specials such as bends, tees, reducers, flanges & plugs etc. fixing at floor level with cement concrete 1:2:4 complete as per direction engineer in charge. a) 160 mm dia.

Providing, fixing, jointing and testing in position the following uPVC pipes conforming to IS : 4985 of 6 kg/cm2 pressure rating including all fittings like T - bend , elbow , reducer, clamps etc .with solvent joint and cement concrete around the pipe complete and making good the same complete as required. for internal toilet a) 32 mm dia.

Providing and fixing in position uPVC SWR floor trap conforming to IS:13592 including providing necessary steel support and as per Specification. Making proper connection cutting chase / hole in floors / slabs and bringing the same in proper condition and shape after placing the trap in right position complete as required. The hopper and trap shall be set in cement concrete mix 1:2:4 complete as required. a) 110 mm inlet and 110 mm outlet

Providing and fixing CP brass grating with frame of approved design including setting in floor with cement motor to match with floor finish as per architect requirement. a) Size 100 mm X 100 mm

Providing and fixing floor drain of size -100 mm x 50 mm of approved quality .

Providing and fixing Heavy Class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and FT. a) Size 100 mm X 100 mm

External Sewerage Excavating trenches of required width for pipe, cables etc including excavation for sockets ,& dressing of sides ,ramming of bottoms ,depth upto 1.5m including getting out the excavated soil,& then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming ,watering, etc and disposing of surplus excavated soil as directed, within lead of 50m. All kinds of soil

a) Pipes, cables etc not exceeding 80 mm dia

b) Pipes, cables etc exceeding 80 mm dia but not exceeding 300 mm dia.

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m :

Ordinary rock : a) Pipes, cables etc not exceeding 80 mm dia

b) Pipes, cables etc exceeding 80 mm dia but not exceeding 300 mm dia.

Hard rock (blasting prohibited) a) Pipes, cables etc exceeding 80 mm dia but not exceeding 300 mm dia.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of RCC pipes including bed concrete as per standard design :

a) 150 mm dia

b) 250 mm Dia

c) 300 mm Dia

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete

a) 100 mm diameter

b) 150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipe including bed concrete as per standard design:

a) 100 mm diameter

b) 150 mm diameter

Providing and fixing square mouth SW gully trap class SP-1 complete with CI grating brick masonry chamber and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg. as per standard design. 150x100mm size P type with common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregrate 40mm nominal size ) inside plastering 12 mm thick with cement mortar 1:3 (1 Cement : 3 coarse sand) finished with floating coat of neat cement & making channels in cement concrete 1:2:4 mix (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design: Inside size 90x80cm and 45cm deep including C.I. cover with frame (light duty) 455x610mm internal dimensions total weight of cover and frame to be not less than 38kg (weight of cover 23kg and weight of frame 15 kg) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Extra for depth for manholes Size 90x80 cm Withcommon burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Construction of Septic tank in R.C.C. including excavation in all kind of soil, P.C.C. in 1:3:6 / 1:2:4 R.C.C. M25 work in foundation walls and slabs, Reinforcement steel grade Fe-500, PVC encapsulated orange colour footrest, pre-cast RCC manhole cover and frame of Heavy duty (HD 20) circular shape 560 mm internal diameter, sludge chambers etc. complete with waterproof plaster inside & outside. 25 Users.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

SUBHEAD - XIV : Road and Hardstanding

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Supplying and stacking at site.

63 mm to 45 mm size stone aggregate.

Moorum

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineerin- charge.

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)

Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. Using grade 'A' sealing compound conforming to IS: 1834.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking paint conforming to IS : 164, on bituminous/RCC surface in white/yellow shade, including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete. New work (Two or more coats)

Providing and fixing road stud reflectors complete with nuts, bolts and washers as required as per the direction of Engineer-in-charge.

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete

450 mm dia RCC pipes.

600 mm dia RCC pipes.

900 mm dia RCC pipes.

Providing and laying Polythene sheet (125 micron thick) confirming to IS :2508 antifriction layer on the sub base course complete as per specifications.( Overlaps atjoints of pvc sheet should be 100 mm wide )

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete.

SUBHEAD - XV : Arboriculture, Landscaping work

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Trees Plant

Supply and stacking of Bottle palm plant of ht. 210-240 cm bottom girth 30-35 cm well developed in big HDPE bags.

Supply and stacking of Plumeria alba plant of height 120-135 cm. with 2-3 branches in bags of size 30 cm as per direction of the officer-in-charge

Supply and stacking of Ficus religiosa (Peepal) plant of height 150-165 cm. in big poly bags of size 30 cm as per direction of the officer-in-charge.

Supply and stacking of Azadirachta indica ( Neem ) plant of height 120- 130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Delonix regia (Gulmohar) plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Supply and stacking of Magnolia grandiflora plant of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.v

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) :

a) Screened through sieve of I.S. designation 4.75 mm

Providing and applying anti termite treatment of infected trees i/c all branches/leaves by spraying chemical emulsion 0.5% (Chlorpyriphos 20% EC) concentration through power spray machine (@ 100 ml Chlorpyriphos per tree i/c cost of chemical) and as per direction of officer-in-charge.

Making tree guard 53 cm dia and 1.3 m high as per design from empty coal tar drums, supplied free by the department, including providing and fixing 2 nos M.S. sheet rings 50 x 0.5 mm fixed with rivets complete in all respects including painting inside and outside of tree guard with:

Complete maintenance of trees(out side of lawn area), jobs like making of basin at regular interval i/c watering,weeding,prunning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge. a)Trees for 250 no/(up to 4 & up to 3 year Slow & Fast growing group =11113.25/250=44.45 Cost for per tree per month.

Hedge Plantation Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Providing and applying anti termite treatment of infected trees i/c all branches/leaves by spraying chemical emulsion 0.5% (Chlorpyriphos 20% EC) concentration through power spray machine (@ 100 ml Chlorpyriphos per tree i/c cost of chemical) and as per direction of officer-in-charge.

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) : a) Screened through sieve of I.S. designation 4.75 mm

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)

Hedge Plant Supply and stacking of plant Dombeya mastersii of height 60-75 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of plant Ficus panda of height 45-60 cm. with 6-7 branches and healthy foliage in p.bag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of plant Euphorbia pulcherrima (dark red double bracts) well branched of height 60-75 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge

Supply and stacking of plant Thuja compacta of height 75-90 cm., conical shaped, well formed with healthy foliage in earthen pots of size 30 cm as per direction of the officer-in-charge.

Cutting of designer hedge/edge removing of cut materials, cleaning, hoeing of hedge/edge bed watering manure and applying insecticides and fungicides etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide , lawn mover and brush cutter with fuel will be provided by the Department & other T & P material/articles shall be provided by the contractor.) a) Prestigious works / H.M. house & officers entitled to free Per Sqm accommodation.(as per yard stick 1Mali =1.00Acre)

SUBHEAD - XVI : Furniture

Supply of Computer chair with arms with specification as under :- Overall height - 775mm, Type of chair- central tilt synchronic, Seat Height (Min) - 432mm, Backrest height & width- 490mm & 500mm respectively, Seat width & Depth - 500mm & 465mm respectively, Type of backrest - Cushion, Material of fabric of Seat & backrest - Upholstered with 100% polyester fabric, Density of polyurethane Foam used in seat & backrest - 45±2kg/Cum, Colour - as per approved by engineer-in Charge, etc. All complete. make: Godrej/Equivalent

Supply of Computer Table size 1200x600x750 mm made out of 19 mm thick commercial board with 1 mm thick laminate on sides & front. Top to have 25mm thick postformed board, having drawer, key board and provision of CPU trolley, all drawer ride on telescopic sliding channel and back covered with 6mm thick commercial ply all exposed edges covered with teak wood lipping or PVC lipping (as required) and finish with melamine polish etc., all complete.

Supply of Officer Table made out of 19mm thick commercial board with 1mm lamination on sides and front, top with 25 mm thick postformed board, having 1 Nos drawers ride on telescopic channels & 1 Cupboard with shelf, (Left/Right hand side as required) with locking arrangement and foot rest of size 75x30mm, all exposed edges to have teak wood/rubber wood lipping with melamine polish and inner sides with sprit polish etc., all complete. (a) Table of size 1800x900x750mm

Supply of Standard steel Almirah of Medium size 1266x750x430mm with 3 Nos of adjustable shelf.Made of M.S Sheet conforming to CR-2 Grade Sheet thickness of side, top, bottom & back of Almirah is 0.8mm minimum and sheet thickness of door 1mm. . Three way bolting & Locking arrangement with Powder coating. Colour of paint as per approved by Engineer-In-Charge. Etc. all complete.Make : Godrej /Equivalent.

Slotted angle metal storking perfectly in upright and straight position mild steel sheet 1mm thick and kick mild sheet 1.25mm thick with screw and nuts metric hexagon head black steel 4.6M6x14mm long of overall ht 17mmx915mm wide overall depth 410mm distance between bottom hselves and floor 130mm (Overall +/- 3mm) with red oxide prime and two coat of synthetic paint upto deserve level complete

SUBHEAD - XVII : Dismentling and Demolishing

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :

Of area 3 sq. metres and below

Of area beyond 3 sq. metres

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

Taking down unserviceable submain wiring of any size.

M& L for disconnecting and taking down copper/aluminium point wiring (light Fan, Socket or Power) Complete Including fixtures and fittings such as switches, coiling roses, pendants, regulator, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit complete

Taking down carefully by unscrewing from bords/outlet boxes, fittings & fixtures such as switches, coiling roses, brackets, regulator, sockets, tube light fitting etc. carrying to store & taking credit

Taking down fan, sealing cable end, dismantling blades and removing fan & blades to MES Store complete

Taking down regulator, sealing cable ends & removing regulator to store for keeping in safe custody or for taking credit complete

Disconnecting & taking down carefully old unserviceable DB SPN 4 Way to store for keeping in safe custody or for taking credit complete

Taking down/dismantling existing perished GI Strip of Size 32x6mm from on walls/buried into complete

Taking down U/G Cable any size.

Credit Civil

Old brick

Wooden Door Window

Concrete Debris

Steel

Credit E & M

Old Unserviceable point wiring casing /conduit any type

Old Unserviceable submain wiring any type any description

Old Unserviceable switch socket combination 6/16Amps

Old Unserviceable ceiling rose three terminals

Old Unserviceable ceiling fan regulator any type

Old Unserviceable tube light fitting any type

Old Unserviceable MCBs any type any capacity

Old Unserviceable DBs SPN 4/8 way

Old Unserviceable fuse box

Old Unserviceable AC power socket 20Apms

Old Unserviceable GI earthing material retrieved from earthing

Old Unserviceable GI pipe medium grade 25mm dia

Old Unserviceable LT UG cable any size

Old Unserviceable GI pipe light grade 40mm dia

Old Unserviceable GI funnel wire mesh

SUBHEAD - XVIII : Internal Electrification Work & Power Wiring:

Point Wiring for Light/ Fan/ exhaust fan with 2 runs of 1100V grade 1.5 Sq.mm & 1 run of 1.5 Sq.mm FRLS insulated multistranded Copper wires, run in & including 25mm dia, 2mm thickness FRLS PVC ISI mark conduits concealed in wall after necessary chase cutting with finishing/surface in wall / ceiling conforming to IS 732 including all accessories such as junction boxes, conduit bends, elbows and ceiling rose, anodised GI Switch box with modular switch and the box covered with front plate.

a) One Lights point controlled by one 6A switch.

b) Two Lights point controlled by one 6A switch.

c) One ceiling fan point controlled by one 6A switch With 100W step type Electronic regulator including Concealed MS fan hook box.

d) Exhaust fan point controlled by one 6A switch including ceiling Rose.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed heavy FRLS PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supply and wiring for 6A socket outlet with 2 runs of 2.5 sq. mm FRLS insulated multistranded Copper wire and 1 run of 1.5 sq. mm FRLS insulated multistranded Copper earth wire in existing raceway/conduit. supply and fixing of 6A 5 Pin socket with 6A modular switch in anodized GI box and front plate complete with fixing accessories etc. as required. (Independent)

Supply and wiring with the following size 1100V grade FRLS insulated multistranded Copper wires in and including suitable size heavy duty PVC conduit concealed in wall after necessary chase cutting with finishing / surface on wall / ceiling including all accessories such as junction boxes, bends elbows and end termination with suitable lugs. a) 2 Runs of 2.5 sq.mm wires with 1 Run of 1.5 sq.mm in 25 mm dia PVC conduit ( For circuit wirings)

Supply, installation, testing and commissioning of the single phase heavy duty grease filled double ball bearing, aerodynamically designed heavy gauge aluminium blades, copper wounded, required length down rod, capacitor and impregnated silicon stamping motor etc.a 1400 mm sweep, brilliant white/As directed by Engineer-In-Charge (without regulator)

Exhaust Fans Supply, Installation & Testing of following Suitable RPM exhaust fan suitable for single phase, 240V, AC supply complete with motor, MS louvers, mounting brackets all accessories etc complete. a) 300mm Sweep (Metallic)

Light/Fan Fixtures Supply, Installation, Testing & Commissioning of the following Light Fixture with lamp, Control Gear & All necessary accessories. Luminaries with all electrical accessories & it should be energy efficient, etc are prewired up to the terminal block & mounted on a removable control gear module for ease of maintenance. All electrical connections of the control gear module with the rest of the luminaries should be click fix & require use of no tools. Mounting options should be for both lateral as well as pole top mounting with Lamp Control Gear & Fixing Accessories. All fixtures shall be white colour & supplied with white lamps. All the light fixtures will be finally approved by Architect / Consultant/ Department. Architect / Consultant / Department reserves the right to reject the fittings suggested by the contractor.

a) 10W BULKHEAD LIGHT MAKE-PHILLIPS CAT NO. WT202W LED6S NW PSU S2 PC SJHDJFJ

b)Surface/Suspended Mounted waterproof (IP65) luminiare suitable for single and twin T8 TLED lamps.

c)38W LED

d) 11W LED Mirror wall Light Fixture.

Power Wiring Supply, installation, testing and commissioning of 6 / 16A, 5 pin shuttered type socket controlled by one 16A modular switch of combination type with indication lamp including wiring with 2runs of 2.5sq.mm & 1run of 1.5sq.mm FRLS insulated multistranded copper conductor wire of 1100V grade laid in heavy gauge 25mm dia FRLS PVC conduit concealed in wall / ceiling including all accessories such as junction boxes, conduit bends, elbows and ceiling rose, anodised GI switch box of adequate size with modular switch, socket and the box covered with front plate. Cutting, chases in wall and making them good after fixing modular type switches as per requirement in sheet steel boxes of adequate sizes to accommodate switches, sockets, etc. complete as required. (Wiring from DB to Socket)

Supply, installation, testing and commissioning of factory made 20A, metal clad socket outlet controlled by 20A, 10kA, SP MCB, in and including MS painted box in concealed manner of adequate sizes including plug top with necessary accessories including wiring with 2runs of 4.0sq.mm & 1run of 2.5sq.mm FRLS insulated multistranded copper conductor wire of 1100V grade in heavy gauge 25mm dia FRLS PVC conduit concealed in wall / ceiling along with required accessories including all accessories such as junction boxes, conduit bends, elbows and ceiling rose. Cutting, chases in wall and making them good after fixing of metal clad socket outlet as per requirement etc. complete as required. (Wiring from DB to metal clad socket outlet)

Supply, installation, testing and commissioning of following rating socket / switch Fuse units in enclosure and plug top on angel iron frame work & other MS support structure complete with all fixing accessories, hardware etc. complete as required .

a) 16A ,415V ,4P, socket outlet with plug top and metal chained cover in sheet steel enclosure,4P MCB,complete etc as required.

b) 25A ,415V ,4P+Earth, socket outlet with plug top and metal chained cover in sheet steel enclosure,4P MCB,complete etc as required.

c) 32A ,415V ,4P+Earth,socket outlet with plug top and metal chained cover in sheet steel enclosure,4P MCB,complete etc as required.

d) 63A ,415V ,4P+Earth, socket outlet with plug top and metal chained cover in sheet steel enclosure,4P MCB,complete etc as required.

Supply Installation Testing and commissioning of SPN/TPN MCB Double door Distribution boards dust and vermin protected and rated for 230/415V Single/Three Phase AC supply operation including incoming MCB /ELCB as per specifications and required capacity Neutral bar and Earth terminal complete as required and installed in concealed in wall after necessary chase cutting with finishing / surface in wall including all fixing materials required. MCBs shall conform to IS : 8828 and ELCB shall conform to IS :12640. All MCBs shall be 'C' Curve. DBs shall be provided along with required wire adopter boxes around the DB as required and dummys for spare ways in the DB (No claim shall be allowed for the same).

a) 8Way SPN MCB DB with 40A, 100mA 2Pole RCBO as incomer and 6nos 6-32A SPMCBs as outgoings.

b) 6Way TPNMCBDB with 63A, 100mA 4Pole RCBO as incomer and 18nos 6-32A SPMCBs as outgoings.

Supply installation testing and commissioning of Vertical type MCB Double door Distribution boards dust and vermin protected and AC supply operation including incoming MCCB/ MCB/ ELCB / RCBO as per specifications and required capacity Neutral bar and Earth Terminal complete as required and installed in concealed in wall after necessary chase cutting with finishing / surface on wall including all fixing materials required. All MCBs shall be "C" Curve. a)8 Way VTPN MCBDB with 160A, 25kA 4 Pole MCCB as incomer and 8Nos 63A TP MCBs as outgoing..

Wiring for FLP Fixtures Supply and Wiring with the following size 1100V grade XLPE insulated Copper armoured conductor cables conforming to IS 7098 Part II with Flame proof junction boxes on existing surface/ recessed steel/ PVC conduit/cable tray as required. including all accessories complete. GTP approved by the Engineer-in-Charge.

(a) 3 Core 2.5 sq.mm armoured (Copper) 2XWY

(b) 3C x 4 sq.mm armoured (Copper) 2XWY

(c) 4C x 6 sq.mm armoured (Copper) 2XWY

(d) 4C x 10 sq.mm armoured (Copper) 2XWY

(e) 4C x 16. sq.mm armoured (Copper) 2XWY

Providing end terminations with Copper lugs, using Insulation tape, crimping tool etc complete as required.

(a) 3/4 Core 2.5/4 sq.mm armoured (Copper) 2XWY

(b) 4 Core 6/10 sq.mm armoured (Copper) 2XWY

(c) 4C x 16sq.mm FRLS armoured Copper conductor cable

Supply, installation, testing and commissioning of following rating FLP socket / switch Fuse units in FLP enclosure and plug top on angel iron frame work & other MS support structure complete with all fixing accessories, hardware etc. complete as required The FLP Sockets / SFUs shall be confirming to IP-65.

a) 16A ,250V ,2P+Earth,FLP socket outlet with plug top and metal chained cover in sheet steel enclosure.,complete.

b) 16A ,415V ,4P,FLP socket outlet with plug top and metal chained cover in sheet steel enclosure.,complete.

c) 25A ,415V ,4P+Earth,FLP socket outlet with plug top and metal chained cover in sheet steel enclosure.,complete.

d) 32A ,415V ,4P+Earth,FLP socket outlet with plug top and metal chained cover in sheet steel enclosure.,complete.

e) 63A ,415V ,4P+Earth,FLP socket outlet with plug top and metal chained cover in sheet steel enclosure.,complete.

FLP Fixtures Supply and Installation of following FLP/Well Glass fixtures made out of Cast Aluminium alloy, toughened clear glass cemented into a bazel ring which is bolted to the body, and lamp holder with Insulator mounted on a bush plate and secured with screws. The body shall be finished with epoxy Grey stove enamelled outside and White inside. The fixture shall be inclusive of all accessories including lamp & control gear box containing Choke, condencer & igniter suitable for Lamp

a) FLP-WP Fluorescent fixture for power saving lamps with wire guard internal reflector, Twinx36 Wpl lamp

b) 2X20W LED FLP fixtures

c) 2X36W LED FLP fixtures

Supply installation testing and commissioning of following rating FLP socket/ switch units in FLP enclosure installed on angle iron frame work complete with all fixing accessories a) 10A FLP Switch

Supply, installation, testing and commissioning of following rating FLP socket / switch Fuse units in FLP enclosure and plug top on angel iron frame work & other MS support structure complete with all fixing accessories, hardware etc. complete as required The FLP Sockets / SFUs shall be confirming to IP-65.

(a) FLP-WP multiplr entry junction box in LM6 or Cast Iron of size 125mm dia 75mm ,

(b) FLP-WP multiplr entry junction box in LM6 or Cast Iron of size 200x250x110,

(c) FLP 4way Junction box of size 125 dia x 100mm depth

(d) FLP 4way Junction box of size 200 dia x 150mm depth

(e) S.P. 16 amps, FLP Switch Rotary Type

Supply, installation, testing and commissioning of 380mm sweep FLP Grade Wall Mounted fans with louvers, including electrical connection, all fixing accessories/ installation materials as required, complete.

Supply, installation, testing and commissioning of 380mm sweep FLP Grade Exhaust fans with louvers, including electrical connection, all fixing accessories/ installation materials as required, complete.

Supply, installation, testing and commissioning of TPN MCB Distribution boards FLP Grade, dust and vermin protected and rated for 415V Three Phase AC supply operation including incoming MCB /ELCB as per specifications and required capacity Neutral bar and Earth terminal complete as required and installed in flush with wall including all fixing materials required. MCBs shall conform to IS : 8828 and ELCB shall conform to IS :12640. All MCBs shall be 'C' Curve. (FLP Grade Distribution Boards with FLP Enclosure). a) 6 Way TPN FLP MCB DB with 100A, 4P RCBO, 100mA as incomer and 12nos 6-32A SP MCBs or 4nos. 6-40A TP MCBs or any combination as outgoings.

Supply, installation of 8 mm dia, MS hook in the slab for mounting light fixtures

Supply and installation of FLP 4 way Junction box of size ( 160x160x110) depth suitable for 3/4" dia cable entries

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required ).

Telephone & Lan Wiring- Supply & fixing of RJ - 11 modular type telephone sockets with shutter in a GI box with front plate and in concealed manner by cutting chasing in walls and making them good after fixing socket, etc., complete as required.

Supply & fixing of RJ - 45 modular type LAN sockets with shutter in a GI box with front plate and in concealed manner by cutting chasing in walls and making them good after fixing socket, etc., complete as required.

Supplying and laying of 2 Pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone wire in the surface/ recessed 25mm dia. heavy gauge FRLS PVC conduit as required. (Telephone cable conforming to DOT specification)

Supplying and laying of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed 25mm dia. heavy gauge FRLS PVC conduit as required.

Supplying and laying of 20 Pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, armored telephone cable in the surface/ recessed Suitable dia. heavy gauge FRLS PVC conduit as required. (Telephone cable conforming to DOT specification)

Supplying and fixing of 8-way spliters in die cast Al. casing etc complete.

Supply and installation of following size Krone connectors in MS box in concealed manner by cutting chasing in walls and making them good etc complete as required. a) 20 Pair

Supply and laying of following pair 0.5mm dia Jelly filled armoured copper conductor Telephone cable in ground at 600mm below ground level including excavation, all kinds of soil, SDR & Hard Rock and refilling of earth, laying of cables, providing protection with sand and brics on top and side and cable route markers at every 15 mtrs interval and also at the turnings. complete as required and as directed by Engr-in-charge. (Telephone cable conforming to DOT specification) a) 20 Pair

SUBHEAD - XIX : Shop Electricals:

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required. (80 mm dia)

Supply and laying of 80mm dia. Class B G.I. pipes surface mounted on ceiling & embedded in wall including all fixing accessories, complete as required.

Supply and fixing of following size Powder Coated Cable Trunking made out of 2mm thick base and cover, couplers & anchor fasteners for fixing the cable trunking, complete as required.

a) 100mm wide x 40mm deep powder coated trunking with cover

b) 150mm wide x 40mm deep powder coated trunking with cover

c) 300mm wide x 40mm deep powder coated trunking with cover

Supplying and laying of following size HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS code complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required a)90 mm dia HDPE Pipe

SUBHEAD - XX : Lightning Protection:

Earth Stations for Lightning Protection Providing Chemical type maintenance free Earth station with consisting of 65 mm dia, standard length (as per equipment supplier) electrode capsule, filled with earth enhancing compound, seald at both ends and brazed lead for connection at one end, suitable for direct installation at site, at a depth of 2.5mtrs. Earth Enhanced compound upto a depth of 2.0meters arround the electrode capsule. Brick chamber & CI Cover complete

Supply and laying of following size earth strips with including connection/ terminating to Earth Station with G.I. nut-bolts, spring washer, bi-metallic strip, exothermic welding etc. as required.

a) 32 X 6mm Aluminium strip conductor with DMC Insulated Supports on 150x150x100mm PCC blocks at Building's Terrace Level

b) 32 X 6mm Aluminium strip conductor with DMC Insulated Supports without PCC blocks

c) 50 X 5mm hot dip GI Strip laid in Ground

Supply and fixing of weather proof 14 SWG GI test link box of size 150 x 100 x 100 mm along with bi-metallic strip and all fixing accessories etc., complete.

Supply and fixing of vertical air terminals comprising of 1.5 Mtr. long 25mm dia copper thick pipe with copper sphere on top and 5 Nos. 6mm dia. 90mm long copper spikes fixed by threading arrangements to copper sphere, 150x150x5mm aluminium base plate including and fixing of suitable mounting arrangements for air terminal on the top of the buildings/ high mast/ tower as required and as per standards, complete as required.

SUBHEAD - XXI: Earthing System:

Earth Stations for Body Earthing, Special Earthing- a) Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

b) Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

c) Providing Chemical type maintenance free Earth station with consisting of 65 mm dia, standard length (as per equipment supplier) electrode capsule, filled with earth enhancing compound, seald at both ends and brazed lead for connection at one end, suitable for direct installation at site, at a depth of 2.5mtrs. Earth Enhanced compound upto a depth of 2.0meters arround the electrode capsule. Brick chamber & CI Cover complete suitable to achive 1 ohm or less then 1ohm.

d)Supply, laying and testing of earth conductor with 28mm dia MS rods in ground at 300mm below ground level in a grid of 1000X1000mm including cutting, welding with 75X6mm MS strip at junctions etc as required. Including Back filling fine soil /clay without stone or cement material

Supply and laying of following size earth strips at 0.5 Mtr below ground including excavation and refilling of earth when laid in ground and with all fixing accessories when laid in trench with including connection/ terminating to Earth Station with G.I. nut-bolts, spring washer, bi-metallic strip, exothermic welding etc. as required.

a) 25 X 5mm hot dip GI strip laid in ground

b) 25 X 5mm hot dip GI strip on cable trays/ walls without excavation

c) 50 X 5mm hot dip GI strip on cable trays/ walls without excavation

d) 25 X 5mm Electrolytic Grade Copper strip in ground

e) 25 X 5mm Electrolytic Grade Copper strip on cable trays/ walls without excavation

f) 50 X 5mm Electrolytic Grade Copper strip in ground

g) Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

h) 25 X 5mm Electrolytic Grade Copper strip with DMC insulated supports

i) 10.0 sq. mm. Copper green PVC insulated wire on cable trays/ walls without excavation

j) Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

k) Providing and fixing of earth bus of 25 x 5mm Electrolytic Grade Copper strip & 500mm overall length with drill of M8 at every 25mm interval mounted on insulators

l) Supply and fixing of Static Discharge Handles made out of 20mm dia and 600mm length Copper Rod fixed on wall with brass spacers and connected to copper strip

Providing Spiral coil earthing with 8 SWG GI wire including spreading of salt and charcoal as per IS 3043/87 with latest amendments.

SUBHEAD - XXII : CCTV System:

Supply Installation testing and commissioning of 3 MP Dome Camera - SITC of 3Mpx Indoor dome 2048 x 1536 at 30fps, Autofocus Motorized remote zoom lens 2.8 - 12mm, H.265, H.264 compression, 50mtr Adaptive IR, 120dB true WDR as per IEC 62676. Minimum Illuminator @F1.4 0.016lux color; 0.007lux Mono, 3D noise filtering, Bi directional Full Duplex Audio, inbuilt mic, 1 Alarm In, 1 Alarm out, 3 independant stream, 8nos of configurable privacy mask, Supported protocol - TCP/IP, Ipv4 & IPv6,UDP/IP, DNS, DDNS,ARP, ICMP, IGMP, RTCP, SFTP, SIP, TLS/TTLS, ARP.802.1x (EAP-MD5, EAPTLS, EAP-TTLS, EAP-PEAP and EAP FAST). Edge based analytics -Object Counting, Adaptive Motion, Object Removal, Motion Detection, Camera Sabotage, Audio Detection, and Directional Motion. Camera shall features of Corridor mode, Mirror mode, having SD

card provision of 2TB, Operating temperature -10 to +55deg C,IP64, IK10,Works on PoE, 24 VAC & 12VDC, Power consumption 12W, ONVIF profile S,G & T,Cybersecrutiy Cert:UL/NDAA, CE - EN 55032 (Class A), EN 50130-4, EN 60950-1,FCC (Class A) - 47 CFR Part 15,UL and cUL Listed - UL 60950-1, CAN/CSA-C22.2 No. 60950-1-07, BIS certified.to ruggedized performace camera should meet Shock & Vibration Certifcation:IEC 60068:2-6 and 2-27 The Camera to be provided by OEM should not be complying to GB28181, GB/T28181-2011 standards and there should be no option to activate or deactivate GB/T 28181 standards in the camera web page/Settings.

Supply INstallation testing and commissioning of 3 MP Bullet Camera - SITC of 3Mpx Indoor dome 2048 x 1536 at 30fps, Autofocus Motorized remote zoom lens 2.8 - 12mm, H.265, H.264 compression, 50mtr Adaptive IR, 120dB true WDR as per IEC 62676. Minimum Illuminator @F1.4 0.016lux color; 0.007lux Mono, 3D noise filtering, Bi directional Full Duplex Audio, inbuilt mic, 1 Alarm In, 1 Alarm out, 3 independant stream, 8nos of configurable privacy mask, Supported protocol - TCP/IP, Ipv4 & IPv6,UDP/IP, DNS, DDNS,ARP, ICMP, IGMP, RTCP, SFTP, SIP, TLS/TTLS, ARP.802.1x (EAP-MD5, EAPTLS, EAP-TTLS, EAP-PEAP and EAP FAST). Edge based analytics -Object Counting, Adaptive Motion, Object Removal, Motion Detection, Camera Sabotage, Audio Detection, and Directional Motion. Camera shall features of

Corridor mode, Mirror mode, having SD card provision of 2TB, Operating temperature -10 to +55deg C,IP64, IK10,Works on PoE, 24 VAC & 12VDC, Power consumption 12W, ONVIF profile S,G & T,Cybersecrutiy Cert:UL/NDAA, CE - EN 55032 (Class A), EN 50130-4, EN 60950-1,FCC (Class A) - 47 CFR Part 15,UL and cUL Listed - UL 60950-1, CAN/CSA-C22.2 No. 60950-1-07, BIS certified.to ruggedized performace camera should meet Shock & Vibration Certifcation:IEC 60068:2-6 and 2-27 The Camera to be provided by OEM should not be complying to GB28181, GB/T28181-2011 standards and there should be no option to activate or deactivate GB/T 28181 standards in the camera web page/Settings.

Supply Installation testing and commissioning of 2 MP PTZ Camera - SITC of 1/2.8", 2Mpx IR PTZ dome 1920 x 1080 at 60fps, Focal length 4.5 - 135mm, Horizontal angle of view: 58.3° (wide) ~ 2.34° (tele); 150mtr Adaptive IR, 100dB WDR,0.1 lux at color, Shutter range: 1 ~ 1/10,000 sec, Electronic image stabilization, Edge based analytics - Motion Detection, Camera Sabotage, BLC, protocol support -IPv4 & Ipv6,802.1x (EAP), TLS1.2, ARP, ICMP, IGMP, DNS, DHCP, TCP/IP. Pan 360deg continuous, Tilt range: +15 to - 90deg, Pan preset speed: 300°/sec; Tilt preset speed: 145°/sec, 256presets, having SD

card provision of 2TB, Aluminum construction, 16 configurable privacy masks, Operating temperature -40 to +60deg C, IP66, Type 4X Certification, IK10 Enclosure, Works on (802.3bt), 24 VAC & 48 VDC, ONVIF profile S,G, & T, UL, CE, FCC, BIS certified. With require accessories wall mount, pole bracket etc.. The Camera to be provided by OEM should not be complying to GB28181, GB/T28181-2011 standards and there should be no option to activate or deactivate GB/T 28181 standards in the camera web page/Settings. if required Fabrication work for Pole Mounting arrangement of PTZ camera

Supply INstallation testing and commissioning of 64 Chanel NVR - Supply installation Testing and Commissioing of Video Management Recording servers .it should supports upto 64 cameras for future upgradation .It should have Intel® Core i5- 9500 or better with 16 GB DDR4 ECC RAM or better. It should run on Windows® 10 IoT Enterprise 64-bit (LTSB) or latest.It should have M2. NVMe 256 GB for operating system.Shall support Dynamic Host Communication Protocol ( DHCP ) and Network Time Syncronisation Protocol ( NTP ) functionality. It shall have Mapping function. it should have in built plugins to integrate third party systems. Each Box should have Thoughput should be 200 Mbps. ,*Video Outputs- 4x Mini Display port 1.4 ,*VMS Should support ONVIF S,G & T ,Should have NVIDIA Quadro P620 (2 GB memory) ,Should have 1xGigabit Ethernet (1000Base-T) ports,1x 10 Gigabit Ethernet (10 G Base-T)

Supply , Installation,testing and commissioning of 24 port L3 Managed core Switch - 24 x 100/1G , 4 x 1G/10G SFP+ Ports , 4 x 10/25G SFP28 Ports with a slot for optional module, Redundant Hot Swappable Power Supply - AC/DC , Virtual stack Upto 8 Switch , 4GB or better, 16 GB Flash, SFP Should be from the same OEM . , 960Gbs or better , 540 Mpps or better , support for 64k Mac addess, 144k Ipv4 and 72 Ipv6 routes , Support for Egress rate limiting, Eight egress queues per port, IEEE 802.1Q, 802.3x, DiffServ, Jumbo frame Ipv4/ IPv6, MACSEC on 10G uplink ports , IGMP Snooping V1, V2, V3, MLD, PIM SM/PIMSSM/PIM-DM/PIM-Bidirectional, DVMRP, OSPF, RIP, BGP, IS-IS, ITU-T G.8032, IEEE 802.1s,

IEEE 802.3ad/802.1AX Link Aggregation Control Protocol (LACP), Ipv4/Ipv6, DHCP Option 82, BPDU, STP Root Guard, SIP detection, SPB or MPLS, IEEE 802.1ae, MIB, NTP, Macsec , SNMP V1,V2,V3, Web GUI, CLI, USB or equivalentmemory card, IP v6 management feature on openstandards, IEEE 802.1ag, TDM or equivalent standards , Should support Access Control Lists (ACLs), DHCP snooping, IEEE802.1x based port authentication, RADIUS/ TACACS+, SSL, SSH, port mirroring,NTP, IEEE 1588, AES, Syslog, MD5, LLDP-MED , IEEE802.1q, IEEE802.1d, IEEE802.1s, IEEE802.1w, ITU-T G.8032 ring resilience/ring protection, VRRP , Working memory/ Recovery memory , '0 to 45Deg ,CE, EN 55032, RoHS US UL 60950, CSA22.2 FIPS 140-2, EAL2 or equivalentEN 60825-1/2 Laser

Supply Installation Testing & Commissioning of Switch 24 Port POE Giga Port Switch - GigE fixed chassis 24 RJ-45 PoE 10/100/1G BaseT, 2 fixed RJ45/SFP combo (1G), 2 fixed SFP+ (1G) uplink or 10G stacking ports. 1RU size, internal 600W AC power supply. Includes United States power cord, guides, and 19" rack mount hardware.

Supply installation Testing and Commissioing of Video Management Softwarwe VMS should have smart motion Search for server side motion detection and quick retrieval of events *Edge Storage Auto Gap Fill functionality detects when a gap in local camera recording occurs, and automatically downloads video and audio (if present) to fill the gap *web based client allows viewing and exporting video without installing any software.*Imports users and roles from existing LDAP servers to reduce administrative overhead, and enables single sign-on (SSO) *Capable of listening for ASCII

commands on a serial and Ethernet port simultaneously *Supports shared displays so operators can send video to surveillance personnel who need it most *Check on VMS and camera health using SNMP *Supports IPv4 and IPv6 cameras *Enables and supports Risk Management Framework (RMF) *TLS-based encryption over HTTPS *Extensible through mapping and plugins, including video information overlays and license plate recognition *should include feature, which is capable of polling for alarms from devices and performing specified actions when an alarm state change occurs *Incorporates FIPS 140-2 validated cryptographic modules. To ensure seamless deep integration VMS should be of same camera OEM

Supply, Installation, Testing & Commissioning of 6TB HD

Supply, Installation , testing and commissioning of 12 V SMPS DC Power Supply Unit, highly regulated and spikes free terminal voltage and heavy sourcing current for regulated terminal voltage

Supply, Installation , testing and commissioning of 55 inches UHD 3840 x 2160 (16:9) Direct-lit LED Display with brightness of 500 nits, viewing angle of 178° h/v. Display should be supplied with necessary mounting bracket as required

Supply, Installation, testing and commissioning of UTP 4 pair 23 AWG CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 4 Pair CAT6 Unshielded, Twisted Pair (U/UTP) Cable 305 mtr per Box. Blue/Orange/White/Green in colour conforming to the following standards like ANSI EIA/TIA 568 C.2, EN50173, IEC 11801 3rd ED, frequency tested upto 700Mhz with Third Party Certificate etc. Cable Dia 6.1 ± 0.3, Cross-member (+) fluted Spine/isolator for uniform separation for all pairs.

Supply, Installation, testing and commissioning of Cat6 Tool less Information outlet for Data & Voice. Cat6 U/UTP RJ45 socket with built in crimping mechanism with capability of retermination without refreshing the wires. Toolless RJ45 Information outlet with insertion cycle (in & out) should be 2500 times (I/O) along with front side Label holder and transparent shutter. The Information Outlet connector shall be of gold/nickel, thickness of gold > 0.8 μm. The connectors shall be compatible as per IEEE 802.3bt standard for POE++ application

Supply , Installation , Testing and commissioning of CAT 6 jack panel

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); Memory: 4GB, NON-ECC, 1600MHZ; RAM: 4GB (1x4GB) Non-ECC DDR3 1600MHz SDRAM Memory; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; 20" TFT Monitor; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit.

Supply and laying of 25mm dia, 2.00mm thikness heavy duty FRLS PVC conduit concealed in wall / ceiling / floor including all accessories such as Junction boxes, conduit bends, etc. completed as required.

Supply, installation, testing and commisioning of 19" rack 32 U floor mount rack with all standard aceessories that include cable manager, fan, power bar with sockets etc. as per requirement

Supply, installation, testing and commisioning of 19" rack 9 U wall mount rack with all standard aceessories that include cable manager, fan, power bar with sockets etc. as per requirement

CAT6 UTP 24 AWG Patch Cord - 1 mtr with cross separator , Manufactured from stranded wires for longer flex-life , Minimum length of 1m, and maximum length of 5m Conforming to the following standards like EN 50173, ISO/IEC 60603-7 & 11801/IEC 60332-1, UL VW-1 with tensile strength >50N, number of insertion is 750

Supply, Installation, testing and commissioning of 24 port Cat 6 19" Modular Toolless Patch Panel (loaded) enable all possible combinations of the various types of cable (UTP, FTP, SFTP) mounted on the same panel by using various toolless connector blocks/modules. Have a metal structure enabling them to be durably fixed to the uprights of the 19” chassis and assuring automatic grounding between toolless RJ-45 connectors, the panel, and the 19” uprights of the enclosure. Include rear cable support with plastic cable guides to hold cable without need for cable ties. Include quick mounting system to mount the panel into the 19” rails without use of cage-nuts.

These may be used to secure the connections of wifi access points, IP cameras, servers, or other critical devices. Front Removal IO's option for maintenance and trouble shooting with 6 Different Colours Labels for Labelling & Identification of Individual Ports. Tested and guaranteed under dual circuit IEEE PoE++ up to 90W for up to 2500 on-load connections / disconnections.

SUBHEAD - XXIII : External Power Supply & Area Lighting:

Supply of following size 1.1KV grade XLPE insulated armoured aluminium/copper conductor cables. When the cable is to be laid in ground, the same shall be laid at a depth of 750mm below ground level including excavation in all kind of soil, SDR, refilling of earth after cables are laid, providing protection with sand cushioning at bottom and PCC blocks/ bricks at sides & top, cable route markers at every 15mtr. interval also at the turnings & joints and identification tag at both the ends etc., complete. The cable shall conform to IS: 7098 Part 1/1988.

a) 3.5C X 300 Sq.mm A2XFY

b) 3.5C X 95 Sq.mm A2XFY

c) 3.5C X 70 Sq.mm A2XFY

d) 4C X 25 Sq.mm A2XFY

e) 4Core 16 sq.mm A2XFY

f) 4Core 10 sq.mm A2XFY

g) 3Core 4 sq.mm 2XWY

h) 3C X 6 sq. mm. 2XWY

i) 19C X 2.5 sq.mm 2XWY

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

a) Upto 35 Sq.mm

b) Above 35 Sq.mm. and upto 95 Sq.mm.

c) Above 185 Sq.mm. and upto 400 Sq.mm.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

a) Upto 35 Sq.mm.

b) Above 35 Sq.mm. and upto 95 Sq.mm.

c) Above 185 Sq.mm. and upto 400 Sq.mm.

CABLE END TERMINATIONS Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

a) 3.5C X 300 Sq.mm

b) 3.5C X 95 Sq.mm

c) 3.5C X 70 Sq.mm

d) 4C X 25 Sq.mm

e) 4Core 16 sq.mm

f) 4Core 10 sq.mm

g) 3/4C X 4/6 sq. mm. (Copper)

h) 19C X 2.5 sq. mm. (Copper)

Supply, erection, testing and commissioning of Garden Lighting Pole of 4.50 Mtr. high (above ground), 100mm bottom dia and 3mm thick including 45W LED Post Top Latern Light fitting, designed Galvanised pole shall be structurally sound, built-in control box with service door including lock and safety chain consisting suitable connector for termination box including necessary fixing arrangement, the control gear tray is prewired with suitable rating of MCB, terminal connectors for loop-in loop-out arrangement, Pole Finish : Coated with epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint, Installation : Surface mounted with 10mm thick GI base plate and fitted on a pre-formed foundation, J type foundation nut-bolts, suitable PVC/ HDPE sleeves for incoming and outgoing cable,

including earthing arrangement, excavation & back filling, bedding, PCC foundations 1:2:4, coping, PCC Pedestal, The wiring from Junction box to Light fixture shall be carried out with 3core 1.5sq.mm multistranded copper flexible cable. Suitable bracket/ reducer with accessories shall be provided to suit the fixture mounting.

The pole shall be fixed with 1no. 45W (-5% without affecting lumens output) LED post top lantern light fitting, lumens output greater than or equal to 4950 lumens, integrated design, mounting on pole. Post top fixture made of die-cast aluminum spigot for mounting LED driver and spun aluminum canopy which is painted white inside and epoxy powder coated matt black finish. High quality polycarbonate cover diffuser. Totally weather proof (IP-54 protection), bottom entry type. Prewired with LED driver and suitable for operation on 240V, 50Hz single phase ac supply.

The driver shall be constant current/ constant voltage output, power factor more than 0.95, THD less than 10%, 5kV over voltage protection/ surge protection and radio frequency noise suppression circuit as per IEC 61000-4-5, Driver safety requirement standards: IS 15885-2-13, Driver performance standards : IS 16104. Short circuit & over load protection auto recovery. Certification: LM 79 for LED luminaire and LM 80 for LED source. The CRI shall be greater than 70%. Test certificates to be submitted. The Lumens output of the system/ luminaire shall be greater than 110 Lumens/ Watt.

Supply and erection of hot dip GI octagonal street light pole of 8 Mtr. Long, bottom dia – 130mm, top dia – 70mm, hot dip galvanized 80-100 microns, thickness 3 mm, 300x300x12mm GI base plate, J type foundation nut-bolts, earthing studs/terminals, 1.5 Mtr out reach single arm bracket, built-in control box with service door including lock and safety chain consisting suitable connector for termination of 3.5C- 35 sq. mm aluminium cable (2 terminations : 1 Incoming and 1 Outgoing) including necessary fixing arrangement, the control gear tray is prewired with suitable rating of MCB, terminal connectors for loop-in loop-out arrangement,

2nos 40mm dia HDPE Pipes of 1.5mtr. Long for incoming and outgoing cables, including earthing arrangement, excavation & back filling, bedding, PCC foundations 1:2:4, coping, PCC Pedestal complete as required. The wiring from Junction box to Light fixture shall be carried out with 3core 2.5sq.mm multistranded copper conductor cable. Installation: Surface mounted with GI base plate and fitted on a pre-formed foundation.

The pole shall be fixed with 1no. 90W (-5% without affecting lumens output) LED Street light fittings,lumens output greater than or equal to 11250 lumens, integrated design, mounting on single pole arm. Pressure die-cast aluminium alloy for housing (heat sink) for effective thermal management, corrosion resistant integral model, totally weather proof (IP-54 protection), side entry type. Prewired with LED driver and suitable for operation on 240V, 50Hz single phase ac supply.

The driver shall be constant current/ constant voltage output, power factor more than 0.95, THD less than 10%, 10kV over voltage protection/ surge protection and radio frequency noise suppression circuit as per IEC 61000-4-5 housed within the fixture, Driver safety requirement standards: IS 15885-2-13, Driver performance standards : IS 16104. Short circuit & over load protection auto recovery. Certification: LM 79 for LED luminaire and LM 80 for LED source. The CRI shall be greater than 70%. Test certificates to be submitted. The Lumens output of the system/ luminaire shall be greater than or equal to 125 Lumens/ Watt.

Supply, erection, testing and commissioning of 40W (-5% without affecting lumens output) LED street light fitting, weatherproof terminal/ junction box (IP-65) similar to Make : Hensel, Cat No. KF 0402 B/ equivalent including terminal connectors for loop-in loop-out arrangement, wiring from terminal box to the fixture with 3 core 1.5sq.mm multi strand copper flexible cable, wall mounted 2.0M long pole arm (class B GI pipe of suitable size for fixing the light fitting) including necessary fixing & mounting accessories, complete as required.

The LED light fittings shall have lumens output greater than or equal to 5,000 lumens, integrated design, mounting on GI pipe of suitable dia, pressure die-cast aluminium alloy for housing (heat sink) for effective thermal management, corrosion resistant integral model, totally weather proof (IP-54 protection), side entry type. Prewired with LED driver and suitable for operation on 240V, 50Hz single phase ac supply. The driver shall be constant current/ constant voltage output, power factor more than 0.95, THD less than 10%, 10kV over voltage protection/ surge protection and radio frequency noise suppression circuit as per IEC 61000-4-5 housed within the fixture, Driver safety requirement standards: IS 15885-2-13, Driver performance standards : IS 16104. Short circuit & over load protection auto recovery. Certification: LM 79 for LED luminaire and LM 80 for LED source. The CRI shall be greater than 70%. Test certificates to be submitted. The Lumens output of the system/ luminaire shall be greater than or equal to 125 Lumens/ Watt.

SUB HEAD -XXIV : Fire Fighting Work

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

a) 25 mm dia nominal bore

b) 50 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

a) 25 mm nominal bore.

b) 50 mm nominal bore.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

50 mm Dia

150 mm Dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

a) 80 NB Class C

b) 100 NB Class C

c) 150 NB Class C

Supplying and fixing Single headed yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30Metre

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal

Supply, installation, testing and commissioning of weather proof lockable cabinet of made out of M.S. sheet having central opening and 4 mm thick glazed glass doors (Two nos.) suitably marked on the outside with the letters "FIRE HOSE" including necessary locking arrangement and shall be painted as per approved shade. The cabinet shall be suitable to accommodate 2 nos. 30 mtr long Hose pipe & 1 Nos branch pipe nozzle. Including mounting on wall with anchor fastener or on Angle frame where wall is not available. The sign, \" YARD HYDRANT\" BRIGADE INLET\" etc. shall be painted in \"CAPITAL LETTERS in white synthetic paint. Size - 1150 x 800 x 250 (For Yard Hydrant)

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80 mm dia

Providing and fixing Carbon-di-oxide type fire extinguishers consisting of seamless M.S. cylindrical body, internal discharge tube, discharge nozzle, suspension bracket, conforming to IS:2878, finished externally with red enamel paint and fixed to wall with brackets complete with internal charges. a) Capacity 4.5kg

Providing and fixing Foam type fire extinguishers consisting of welded M.S. Cylindrical body, discharge nozzle, suspension bracket, conforming to IS:10204 finished externally with red enamel paint and fixed to wall brackets complete with internal charges a) Capacity 9 litres

Providing and fixing ABC powder type fire extinguishers consisting of welded M.S. Cylindrical body, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube, 30cms long high pressure discharge hose(for only 5Kgs), discharge nozzle,, suspension bracket, conforming to IS:2171 finished externally with red enamel paint and fixed to wall brackets complete with internal charges.

a) Capacity 2 Kg.

b) Capacity 5 Kg.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : a) Pendant type

SUBHEAD - XXV : Air Conditioning Work

Supply, Installation, Testing, commissioning of following capacity Hiwall inverter type 5star Split Units including proper mounting arrangement comprising of angle base frame, along with anchoring and finishing, initial charge of refrigerant, Thermostat, supply and laying of Control cables with end terminations between the Condenser, Evaporator units and Remote including 5 KVA Capacity, wall mounted Stabilizers, and drain pipe & Copper pipe etc all complete as per direction of engineer in charge. 2 TR capacity

QUICK BUILDERS

VISHAL BUILDERS

Surendra Infrastructure Pvt. Ltd.

AMARANTTOSS INFRATECH PRIVATE LIMITED

RIC Projects Pvt. Ltd.