PROVN OF SECURITY FENCING AROUND BLDG NO 25 MALL ROAD PROVN OF CHAIN LINK FENCING AROUND STORE BLDG OF RKT REGT PROVN OF CATTLE FENCING AT OFFICERS MESS OF 132 SATA REGT PROVN OF GUARD ROOM NEAR RP GATE OF 625 SATA BTY AND CERTAIN MINOR WORKS AT NASI

Amount

Excavation in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes etc not exc 10 Sqm on plan and getting out in any type of soil, complete, all as specified & directed.

All as per item No. 1.00 above but exc 1.5 m and not exc 3.0 m in depth.

Excavation in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes etc not exc 10 Sqm on plan and getting out in soft/disintigrated rock, complete, all as specified & directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil, complete, all as specified & directed.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point, complete, all as specified & directed.

M&L for PCC 1:4:8, type D2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete, all as specified & directed.

M&L for PCC 1:3:6, type C2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete, all as specified & directed.

M&L for PCC 1:2:4, type B2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete, all as specified & directed.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete, all as specified & directed.

All as per description of serial item No. 9.00 here-in-before but 8mm dia bar.

All as per description of serial item No. 9.00 here-in-before but 6 to 10mm dia in stirrups, spacers and binders.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like, complete, all as specified & directed. .

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete, complete, all as specified & directed.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like, complete, all as specified & directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete, complete, all as specified & directed.

M&L for reinforced cement concrete M-25 (Design Mix) using 20mm graded crushed stone aggregate in lintels over 1.5m clear span, seismic and other similar bands, lintel bands, plinth bands, roof bands and the like, complete, all as specified & directed.

Formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete, complete, all as specified & directed.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like, complete, all as specified & directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete, complete, all as specified & directed.

Formwork to edges of concrete flats, roofs, floors etc and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces, complete, all as specified & directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted stone masonry built in cement mortar 1:6 complete all as specified & as directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6, complete, all as specified & directed.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls , built in cement mortar 1:4, complete, all as specified & directed.

Supply only integral water proofing compound (ISI marked).

M&L for APP modified polymeric water proofing membrane, 2 mm thick having centre core not less than 100 micron high molecular high density polythelene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3 Kg/Sqm applied with bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.2 Kg/Sqm over bitumen primer conforming to IS-3384 @ 0.40 Kg/Sqm with final coat of bonding bitumen grade 85/25 @ 1.2 Kg/Sqm over APP membrane with all overlaps, complete, all as specified & directed.

M&L for rendering 10mm thick in cement mortar 1:4 on roof top surfaces, mixed with water proofing compound as per manufacturer's instruction, finished even & smooth without using extra cement, complete, all as specified & directed.

M&L for 40mm thick (average consolidated thickness) type B0 using 12.5mm graded stone aggregate as in padding even and smooth without using extra cement with existing slope with 'V' shaped grooves 6mm wide and 10mm deep @ 1.2m interval or part thereof, both ways on top of padding and filled with mastic bitumen of 1:1 proportion, complete, all as specified & directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete, all as specified & directed.

All as per description of serial item No. 28.00 above but in cement mortar 1:6

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of primer, complete, all as specified & directed.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete, all as specified & directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete, all as specified & directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1 mm thick finished coat of white wall care putty, complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of ceilings & applying three coats of white wash, complete, all as specified & directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete, complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of ceiling & applying two coats of cement base paint of approved shade/tint, complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of walls & applying three coats of white wash, complete, all as specified & directed.

M&L for glazed ceramic tiles (coloured) 7mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.16 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete, all as specified and directed.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 ,complete, all as specified and directed.

M&L for machine cut Kota stone slab flooring 20 to 25mm thick as in shelving/window cills or steps in single piece laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 including necessary bull nosing, fixed to wall and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete, all as specified & directed.

M&L for machine cut Kota stone slab flooring 20 to 25mm thick & 550x550mm size, laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete, all as specified & directed.

M&L for 75 mm thick PCC (1:4:8), type D2 using 40 mm graded crushed stone aggregate as in sub base of floor, surface finished fair and even,complete, all as specified & directed.

M&L for machine cut Kota stone slab 20 to 25mm thick on vertical surfaces such as dado, skirting, cills etc. laid over & including screed bed or bedding layer of 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete, all as specified & directed.

M&L for 20mm thick black granite slab of approved shade, as in kitchen platform etc, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing as per local trade practice, complete, all as specified & directed.

S & F Pressed steel frames of size 125 x 60x1.25 mm thick mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified & approved by Engr-In-Charge.

S&F second class hard wood (Hollock/Bonsum/Sal) factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

S&F factory made 35mm thick glazed and skeleton shutters (three panels) made of second class hard wood, open rebated and prepared to receive glass, gauze etc (witht sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete, all as specified & directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications.

S&F factory made solid panel PVC moulded door shutter with particle board core, 28 to 30mm thick (styles) with 2 raised panel design with 2 mm thick moulded PVC sheet on front face & 2mm thick plain colour PVC frame sheet on back face and fixing in frame at site, complete, all as specified & directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked), complete, all as specified & directed.

S&F extruded aluminium alloy handle, 150mm size, cast type, anodized (ISI marked), complete, all as specified & directed.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete, all as specified.

S&F butt hinges of size 100 mm medium weight, cold rolled mild steel ISI marked, complete, all as specified & directed.

S&F small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, articles of 2nd class hardwood, articles not exc 200 cucm each.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer, complete, all as specified & directed.

S&F factory made steel window/ ventilator factory made made out of MS hollow section 79 mm x39 mm x 1.6 mm thick frame with double shutter (glazed & wire gauzed shutter) made out of 'Z' section using flush butt welding and tennon riveting, all as per IS 1038/83, dobby hinges shall be provided to both shutters, locking arrangements, 25mm aluminium knobs to shutter, aluminium hook & eye, 10mm MS square bars in grill, 04 Nos lugs welded to frame 'Z' section handle, 100 mm including necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4, type B1 including two coat of synthetic enamel paint over a coat of zinc crome/red oxide primer, complete, all as specified & directed. Note:- Wire mesh and sheet glass shall be measured and paid separately. with top hung shutter including hinges, steel peg stay, handle complete all as specified.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete, all as specified & directed.

Supply and fixing stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete, all as specified & directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, treating back of chowkats etc area tarred exc 0.10 Sqm but not exc 0.50 Sqm each and treated with tar or coal tar black paint complete, all as specified & directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer, complete, all as specified & directed.

M&L for preparation of new untreated steel and iron surfaces of any description, not exc. 10 cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of zinc chrome primer complete all as specified.

S&F plain, solid, straight chowkats and frames of second class hardwood, wrought, framed rebated on the solid rounded or chamfered, put together with glue, pinned at joints, complete all as specified & directed.

M&L for prelaminated MDF board, exterior grade,prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete, all as specified & directed.

Extra over rates of block board or veneered particle board for 6mm thick external teak wood lipping, complete, all as specified & directed.

S&F magnetic striking plate as per sample approved and directed by Engr-In-Charge.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screwscomplete, all as specified & directed.

Supply & fixing hasp and staple of size 100mm aluminium anodized safety type with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified.

S&F aluminium handle, 100mm size, cast type, anodized (ISI marked) complete all as specified.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors or fixed to wall with clamps, complete, all as specified & directed. .Note :- Excavation, earthwork and wall clamps shall be measured & paid for separately.

All as per description of serial item No. 69.00 above but 75mm bore pipe.

S&F 110 mm bore PVC (SWR) junction single (single ‘T’), equal or unequal with oval access door.

S&F 110mm bore PVC (SWR) bend, any radius with access door.

S&F 75mm bore PVC (SWR) bend, any radius with access door.

S&F 110 mm bore PVC (SWR) vent cowl.

S&F 75 mm bore PVC (SWR) vent cowl.

S&F PVC (SWR) Gully trap 125/110mm, setting and jointing with solvent cement, complete, all as specified & directed.

S&F PVC (SWR) floor trap plain with PTMT grating including jointing with solvent cement, diameter of outlet 75mm, complete, all as specified & directed.

S&F vitreous china wash hand basin, white, flat back of size 580mm x 450mm with including 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete, all as specified & directed.

All as per description of serial item No. 79.00 here-in-before but fixed in repairs.

S&F vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc and, making good to floor, complete all as specified & directed.

S&F PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle, complete, all as specified & directed.

All as per description of serial item No.82.00 above but fixed in repairs

S&F vitreous china urinal, flat back, half stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia, complete, all as specified & directed.

S&F PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides, complete, all as specified & directed.

All as per serial item No. 85.00 here-in-above but fixed in repairs.

S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) of 1000 litre capacity, triple layered, hoisted and fixed in position, complete, all as specified in SSR Part - I and as directed. Note :- (i) The unit rate quoted by tenderer shall be deemed to insulate water tank with GI pipe medium grade 10cm long projected inside and outside of tank with bore suitable for inlet and outlet, GI pipe 20mm bore medium grade projecting 10cm inside and outside of the tank for over flow, GI pipe 20mm bore medium grade projected 10cm inside and outside of tank for vent & mosquito cover for vent/overflow pipe.

Dismantling existing unserviceable, PVC / RCC water tank of capacity n.exc 500 litre each & removing from site complete all as specified and directed.

S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms), complete, all as specified and directed.

Taking up or down steel tubing and connection 15 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

All as per above item No. 89.00 but 20 mm bore pipe.

All as per above item No. 89.00 but 25 mm bore pipe.

M&L for galvanized steel water tubing medium grade of 25 mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors, complete, all as specified & directed.

All as per serial item No. 92.00 here-in-above but of 20 mm bore pipe.

All as per serial item No. 92.00 here-in-above but of 20 mm bore pipe, laid in trenches.

All as per serial item No. 92.00 here-in-above but of 15 mm bore pipe.

S&F 25 mm bore gun metal gate valve with iron wheel head, screwed both ends for iron pipecomplete, all as specified & directed. .

S&F 20 mm bore gun metal gate valve with iron wheel head, screwed both ends for iron pipecomplete, all as specified & directed. .

Cutting existing steel tubing for addition and alteration, screwing the existing steel tubing in position and insertion of required size of GI fittings. (i.e. union, nipple, reducing tee) for branch connection of internal dia 25/20mm dia.

S&F 15 mm bore bib tap, cast copper alloy, fancy type,chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete, all as specified & directed.

All as per description of serial item No. 99.00 here-in-before but fixed in repairs.

S&F 15mm bore angle stop valve fancy type of cast copper alloy chromium plated screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union, complete, all as specified & directed.

All as per description of serial item No. 101.00 here-in-before but fixed in repairs.

S&F 15mm bore Stop valve, fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union, complete, all as specified & directed.

All as per description of serial item No. 103.00 here-in-before but fixed in repairs.

S&F brass chromium plated shower rose 125 mm size with swivel joint including fixing to steel pipe of 15mm bore or union, complete, all as specified & directed.

S&F tubular towel rail, aluminium anodized, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete, all as specified & directed.

All as per description of serial item No. 106.00 here-in-before but fixed in repairs.

S&F soap dish holder (Cat Part No ACN-1131N of make - Jaquar or equivalent of Marc/Parryware/Somany/Parko/Gem/Prayag) complete all as specified & as directed.

All as per description of serial item No. 108.00 here-in-before but fixed in repairs.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface, complete, all as specified & directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection, surface finished fair and even, complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 2 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:1).

S&F mild steel framed work such as grills, gratings, guard bars, barred iron doors, cooler stand, framework of water tanks and similar works, conforming to Grade E-165 (Fe 290), including welding etc. complete all as specified & as directed.

M&L for factory made 60mm thick machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment laid over & including 50 mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

S&F butt hinges of size 100mm extruded aluminium alloy with galvanized mild steel hinge pin, anodized type B-21, complete, all as specified.

M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe, complete, all as specified and directed.

S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc.

Add or deduct for each 25mm girth or part over or under 30cm

M&L for 50mm thick sand stone slab in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc not exc 2m in length, punched dressed on face and along exposed edges, self faced on the other side and set and pointed in cement mortar 1:4 complete.

M&L for cement concrete (1:2:4) type B1 using 20 mm graded crushed stone aggregate as in surface channels, drains & copings, rounded or chamfered on edges all as specified & directed.

Supply & laying FRP septic tank package type waste water treatment system (PWTS) Model No. PWTS-AM-180-01 of Sintex or equivalent approved make of size 1490 mm dia and 1615 mm height including necessary inlet & outlet pipe designed to carry sewage and salvage water, with upflow filter including media including necessary excavation, PCC (1:4:8) below foundation bed, vent pipe, inlet and outlet connection pipe upto 2.00m length etc, complete all as specified and directed. Make :- Sintex or Equivalent MES approved make.

M & L for soakage wells including excavation in any type of soil, foundation in PCC (1:4:8), walls of honey combed fly ash brick masonry with top ring of RCC 1:1.5:3 type A-1 concrete including intercepting chamber and screen chamber made of fly ash brick masonry in CM (1:6), RCC cover slab in1:1.5:3 type A-1 & SFRC MH cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.80m dia & 2.0m effective depth all as per drg No. CEBZ/TD/78 /2011 sh No 1/2 & 2/2 complete all as specified and directed.

Surface excavation in any type of soil not exceeding 30cm deep and averaging 15cm deep and getting out, complete all as specified

M & L for Providing precast cement concrete type C1 1:3:6 (20 mm graded aggregate) in kerbs stone, window or door cills lintels bressumers, steps quoin blocks etc. of any section with plane fair faces including chamfers, weatherings, throating and necessary excavation etc. and setting jointed in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M & L for precast cement concrete 1:2:4 type B1, using 20mm graded stone aggregates as in covers slabs, complete all as specified and directed by the Engineer-in-Charge.

Excavation in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface in soft/ loose soil.

S&F mild steel work as in angle iron in posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) and similar works conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

Supply only mild steel galvanized chain link fencing 3 mm dia of mesh wire, mesh size 75x75 mm complete all as specified and as directed.

Supply only mild steel galvanized chain link fencing 3 mm dia of mesh wire, mesh size 100x100 mm complete all as specified and as directed.

Fixing only mild steel galvanized chain link fencing, any mesh, size and type to any type of standards, rails, straining bolts etc. including provision of binding wire.Note :- Supply only chain link fencing shall be measured and paid for separately.

Supply and fixing 3.00 mm dia galvanised medium coated as per IS 4826 steel wire as required for fixing chain link fencing etc all as specified and dircted by Engr-In-Charge.

Supply and fixing 4.00 mm dia galvanised medium coated as per IS 4826 steel wire as required for fixing chain link fencing etc all as specified and dircted by Engr-In-Charge.

M&L for cement concrete1:2:4 type B1 (20mm graded aggre) as in fixing of vertical post/copping including necessary form work etc complete all as specified and directed ..

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5 cm long and dia of neck 5 to 10 mm complete all as specified.

Surface dressing not exc 15cm deep in soft/loose soil.

S&F galvanized 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossing with and provision of galvanized mild steel wire, staples or steel pins etc as directed.Note :- Each line of horizontal / vertical / diagonal wire to be measured for the purpose of payment.

S&F stainless steel pipe of 50/40/25 mm bore of grade SS-304 as in railing including necessary fittings, complete, all as specified and directed by Engr-In-Charge

S&F powder coated aluminium partition with frame made of standard aluminium section as per IS including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc and fitted with 5 mm thick ACP board in fixed glazed panel, complete, all as specified in clause 10.37 of SSR Part I & directed by Engr-in-Charge.

S&F aluminium door shutters with frame of aluminium section weighing not less than 0.55 Kg/RM including necessary joining cleats, glazing clips, rubber neoprene packing, brass handle and brass tower bolts of size 150mmx 02 Nos in each door, hinges, anodised aluminium snap beading screws, hydraulically regulated double action floor spring made up of 1.25 mm thick aluminium alloy sheet, foundation box for each shutter etc and including fitted with 5 mm thick tinned glass in glazed shutter with brass mortice lock of 100mm , 2 levers, vertical type, complete, all as specified in clause 10.37 of SSR Part I & directed by Engr-in-Charge.

Providing & fixing false ceiling with fibre cement designer tile Ivory painted (High pressure steam cured) of 4mm thickness (As per IS: 14862) of size 595x595mm and any one of the design (Oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (Galvanised @ 120 Gms, both side inclusive) consisting of Main ‘T’ runner with suitably spaced joints to get required length and 15x32mm made from 0.3mm thick sheet, spaced at 1200mm C/C and cross ‘T’ of size 15x32 mm made of 0.30 mm sheet, 1200 mm long spaced between main ‘T’ at 600 mm C/C to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600mm and size 15x32mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 15x20mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including, required cutting/making, opening of services like diffusers, grills, light fittings, fixtures, smoke detectors etc main ‘T’ runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rod of 3mm dia with galvanised butterfly level clips, spaced at 1200 mm C/C along main ‘T’ bottom exposed width of 15mm of all ‘T’ sections shall be centra black pre-painted with polyester paint and having a load bearing capacity of 12 Kg/Sqm, complete at all heights as directed by Engr-In_charge. MAKE :- Everest / Aramstrong

M&L for rolled mild steel angle, or tee sections, fixed independently, without connecting plates, etc. Or welding existing steel or iron surfaces, complete, all as directed by Engr-In-Charge.

Taking down cement or cement lime plaster on stone/brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for preparation old decorated surfaces of walls and providing one coat of cement base paint, complete, all as specified and directed.

M & L for complete removal of existing treatment and preparation wall surfaces and applying two coats of oil bound distemper over a coat of 1 mm thick wall care of putty, complete all as specified and directed.

Demolition of cement concrete (unreinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

M&L for 20mm thick black granite on kitchen platform and similar work (size not less than 900 x 450mm) over & including 15mm thick screed bed in CM 1:6, laid over sand stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified & directed.

M&L for PCC 1:2:4 type B-1 (using 20mm stone crushed agg.) as in edging, rounded or chamfered on edges in any description complete all as specified.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises. complete all as specified and directed.

M&L for ceramic coloured tiles, matt finish 400 x 400 x 7mm thick coloured/Jointless tiles in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with tile, laid over and including screed bed or bedding layer of 15mm thick in CM (1:6) laid over and including 25mm thick PCC (1:2:4) type B-0 using 12.5 graded stone aggregate complete all as speciied and directed.

M&L for ceramic coloured tiles, matt finish 400 x 400 x 7mm thick coloured/Jointless tiles as in skirting/dado, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with tile, laid over and including screed backing of 10mm thick in CM (1:4), complete all as speciied and directed.

Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion as ordered and directed.

S & F in repair 150 mm overhead shower with arm flange for fixing with 15mm pipe complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including plastic white cover closed pattern with flat bottom and mild steel chromium plated hinge device including connections to drain (or outgoing pipe ) and to flushing pipe anti syphonage pipe etc complete all as specified and directed

S&F in repairs sink with drainage board made of stainless steel 1.00 mm thick, kitchen with plugs, washers and waste including fixing cantilever brackets and connecting union overall size not less than 1145mm x 510mm, bowl size 560 x 410 x 200mm complete all as specified and directed..

S&F in repairs stainless steel plate rack made of 0.50mm thick of over all size 920mm x 785 mm x 255 mm and weight not less than 7.00 Kg each of approved quality complete all as specified and directed..

S&F CI Nahani/floor trap 75 mm outlet with grating including jointing to waste pipe fixed in cement concrete, type B1(1:2:4) as in repairs.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each and removing from site and making good disturbed surface of walls in cement mortar (1:3), complete all as specified & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and not exc 4 Sqm each and removing from site and making good disturbed surface of walls in cement mortar (1:3), complete all as specified & directed.

S & F factory made solid pannel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawings on page 146 of SSR Part - II 2004 complete all as specified and directed.

S & F 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F in repair fancy type 20mm dia aluminium curtain rods powder coated fixed to bracket completed all as specified & directed.

S&F decorative type knobs with bracket of MS powder coated for fixing at end of pelmet rod complete al as specified & directed.

M&L for 40 mm thick sand stone slabs; set and jointed over joists etc. in CM 1:4 as in base of water tank & other similar work over and including 25 mm thick PCC 1:2:4 type B-0 (using 12.5mm stone crushed agg.) base, finished concrete surfaces even & smooth complete all as specified and directed

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks etc, including removal to store complete all as specified and directed.

Supply only stack clamp made out of 50x3mm flat iron and 16 mm dia round iron stays fixed to pipe of bore 110mm complete all as specified.

Dismantling of ceiling board/lathing any thickness including frame work complete all as specified and directed.

Dismantling Asbestos Cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified & directed.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ 'L' or 'J' type hook complete all as specified & directed. Make :- Durashine of Tata Blue Scope and Dura Steel of Everest.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ 'L' or 'J' type hook complete all as specified & directed.

S&F steel work in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St -240 complete all as specified and directed.

Dismantling of timber framed scantlings rails, posts, rafters, purlins, etc. under 40 sq. cm in section , in any position complete all as specified and directed

M&L for 50 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone agg as in flooring etc, finished even and smooth, complete all as specified and directed.

M&L for rough cast plaster over 15 mm thick rendering in cement mortar (1:4), as baking coat on stone masonry surfaces complete all as specified & directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, multi stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick( Make - Hylem/Anchor) ISI Marked, brass screws and cup washers including 1.5 Sqmm multi stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed for:- Make of wire- Havells/Polycab/Anchor/Finolex. Make of PVC conduit -AKG/Plaza/Kalinga

One light point/bell point controlled by one, one way switch.

One ceiling fan/exhaust fan point controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One 3 pin 5 Amp socket on independent board.

All as per item No. 175.00 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm Multi stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F Switch piano, flush type, single pole, one way, 5 Amps, 240 volt, 50Hz, AC, complete all as specified and as directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F switch piano flush type 15 Amps, single pole one way 240 volts complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F bell push flush type 5 Amp complete all as specified and directed.

S&F Socket outlet 3 Pin 5/6 Amp flush type complete all as speciied and directed by engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F socket out let 2 in 1, multipurpose 3 pin 15/16 Amp flush type complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F ceiling fan regulator electronic flush , steped type (four step) 230 Volts AC complete all as specified and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F ceiling rose surface bakelite 3 terminals complete all as speciied and directed by Engr-in-Charge .MAKE:-Havells/Anchor/Legrand

S&F bell ding dong type, AC, 230 volt, single pole complete all as specified and directed. .MAKE:-Havells/Anchor/Legrand

S&F LED tube light fitting box type in acrylic linear tube (1x 18 watt),230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as speciied and directed by Engr-in-Charge. Make Havells Cat part No PHOTON ULTRA1213 T8SSTL 18WLED 865SPC (for tube) REGALBATTENT8UPTO1X22WDSBSWH (for batten) Bajaj Cat Part No BLRB 18W CWC for tube , BLRB - DB 118 for batten or equivalent model of Philips/Crompton

S&F aesthetically designed linear LED mirror light fitting 10 Watt provided with a high output PMMA diffuser for glare free light complete with all accessories pre-wired and including connecting flexible copper conductor cable with suitable size. Make :Bajaj / Havells / Crompton

S&F lamp holder PVC/polycarbonate type with back plate complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F of LED lamp 9/11 watt complete all as specified and directed.. MAKE:-Havells/Anchor/Legrand

-BLANK-

Supply & fixing, testing and commissioning energy saving street light luminaire 15 watt LED , aluminium pressure die cast housing with tughened glass cover with individual LED lence , IP 66 protection complete all as specified and directed by Engr-in-Charge. Make- Havells Cat Part No ENDURAPEARLS 15WLED757SASYTOPC, or equivalent model of Surya/C & S.

S&F street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

S&F ceiling fan of 1200 mm sweep, 230 Volts, AC 50 Hz, copper winded, high speed, BEE star rated as per latest norms with motor, blades (03 Nos), down rod, canopy & shackle assembly including 0.5 sq mm three core PVC insulated flexible wire with mulitstranded copper conductor from ceiling rose to connector of ceiling fan and writing of MES No, complete, all as specified and directed by Engr-in-Charge. Make: Havells ES 50 or equivalent from Crompton/ Usha/Orient as approved by the GE.

S&F ventilating fan 230 mm sweep suitable for 230 Volts, Single phase 50 Hz AC supply, metal body with bird guard including connecting with three core flexibale copper cable. Make Bajaj/Usha / Crompton/Havells

S&Ff MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed. Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S & F MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge by Engr-in-Charge. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F of MCB SP, 240 volt, 3 Amp to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge. . Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh, PCC chamber in cement concrete 1:3:6 type C-2 and RCC 1:2:4 type B1 cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing, complete, all as specified & directed.

Supply and, laying, including jointing, testing or fixing or passing through pipe, trench or duct, commissioning and testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 Volt grade size 10 Sqmm, 2 core complete all as specified and directed by Engineer-in-Charge. Make Polycab/Asian/Gloster/Finolex

Supply and laying dry river sand for cable cushioning in trenches to required width at bottom and top cable including spreading, levelling, watering and consolidation, complete all as specified and directed by Engineer-in-charge. Note: Punned thickness only shall be measured and paid.

Supply and laying of bricks of old class ‘B’ as protection cover to UG cable, laid flat adjoining to each other width wise, complete, all as specified.

Supply and laying GI tubing 40 mm bore, light grade with all fittings, laid in trenches/under floor or fixed on pole/on wall for cable protection.

S&F street light Engineering plastic one piece moulding control box with locking arrangement made out of HDPE and FI clamp 25x3mm complete including one MCB SP 6 Amp 240 Volt complete with 02 Nos aluminium busbar of rating 63 Amp for single phase and neutral on porcelain based insulators and fixing clamps to pole for street lights, complete all specified & directed. Make Sintex/ Hensel /SHI/BRITE

Supply, errecting and fixing in true vertical position, steel tubular swaged pole (410 SP-31), 09 metre long, complete with cast iron base plate, pole cap/final taper plug ,bolts, nuts and washers, welded reduced section and longitudinal weld throughout entire lenght of pole, including two coats of black bituminous paint externally upto planting depth and remaining exterior portion of pole shall be provided with one coat of red oxide primer and two coats of aluminium paint, complete all as specified and directed.(Numbering of the poles shall be done with synthetic enameled painted letter of shape & size as directed. Note:- (a) Cost of numbering of pole shall be deemed to included in unit rate. (b) Excavation, Earth work and PCC foundation will be measured and paid for separately.

S&F PVC insulated sheathed copper conductor cable 1.5 sqmm multi-stranded 1100 volt grade, three core for connecting street light fitting, complete, all specified and directed.

S & F LED street light luminaries 72 Watt made of single piece Aluminium Die cast with powder coated in RAL-7032 shade with heat distribution fins onhousing with UV stabilized toughned flass cover and should have secondary lens on each LED for better light distribution .The system luminaire efficiancy should be > 110 LM/W with high power LED's. LED driver should be potted and BIS certified with efficiency > 85 % frequency 50 HZ,Operating voltage range 120V-270V, current not more than 0.320 Amp, PF 0.95, THD (I) < 10 %, supported with 5 KV internal and 10 KV external SPD, Humidity 10% to 90 % RH, working temperature - 20⁰ C to 50⁰ C lige expectancy of LED should be 50000 burning houres with minimum 70 % initial lumene maintained, CRI >70, complete, all as directed. Make:- Cat Part No LSTP-72-CDL-M OF Crompton or equivalent from Philips/Wipro

M&L for carrying out boring under the black top road for crossing of LT cable/protection pipe by mechanical boring machine or otherwise without damaging black top surface of road for fixing of GI pipe 80 mm bore under the road complete all as specified and directed.

Supply, fixing and testing Street light automatic Nature switch of capacity 3 KW single phase complete with using infrared sensor based NATURE SWITCH for automatic switching of street lights. Nature Switch operation should be based on Nautral Light Lux* level. Required illuminance level for switching ON is ≤ 30 Lux and for swiching OFF ≥ 10 Lux. The sensor should also have part night operation facility of min.4 hrs to max 12 hrs. The sensor along with suitable power contactor(s) and incoming-outgoing MCBs should be enclosed in a pole/wall/panel mountable Rust proof, Electric Shock Proof, Termite proof and FR grade thermoplastic polycarbonate Enclosure ( with Hinged LID) conforming to IP66 protection class 2. The circuit should also have provision for Manual Operation(i.e Sensor By-Pass option) Make - Kakatiya Energy system Model SWADEEP-66-3KW 1P or equivalent from Havells .

S&F recess mounted 2'x2' luminaire with white powder coated CRCA housing with LEDs 36 Watt, square shaped complete, all asspecified & directed. Make: Bajaj Cat Part No. BZRSQL 36 W GZ WH, Jaquar Cat Part No. LULT01S36XC or equivalent model of Havells..

Taking down existing ceiling fan/exhaust fan, dismantling blades and refixing after cleaning incl connecting up with three core flexible cable from ceiling rose to fan complete all as specified and directed.

M/s SUNIL ENTERPRISES

M/S Nexus Projects

M/S AL ASMA ENTERPRISES

M/s Jai Jinendra Constructions