SPECIAL REPAIR TO BLDG NO 32 RA LINE (OR LIVING ACCN) OF 409 FD HOSP AND PROVN OF TEMPORARY GUN SHED FOR 06 X GUN 130MM FD M-46 (L-23.4M W-15.5M and H-4.60M) FOR 75 MED REGT UNDER GE (NORTH) MEERUT CANTT

Amount

Taking down cement plaster from brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of brick work or stone boulders masonary built in cement mortar including all arches, pillars etc complete all as specified and directed.

Demolition cement concrete (unreinforced) in ground floor and pavings not exc 15cm thickness (below or above ground level) complete as specified and directed.

Dismantling single layer mangalore attern or similar tiles in roofing complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section, in any position unfraned work complete as specified and directed.

M&L for brick work with fly ash old size bricks straight or curved on plain exc. 6m mean radius built in CM 1:6 complete all as specified and directed. Make - PBC, ECO and EXPERT.

M&L pre-painted Galvalume aluminium zinc coating (AZ-150) GI based corrugated steel sheet 0.5mm thick of Green colour having a tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

M&L pre-painted Galvalume aluminium zinc coating (AZ-150) GI based plain steel sheet 0.5mm thick of Green colour having a tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified and directed.

Supplied and fixed Tee grid suspension system of size 600 mm x600 mm type-1 made out of rolled framed hot dipped galvanised steel zinc coated of not less than 120 gm/sqm ,main runner shall be 0.3 mm thick of section 24 mmX33 mm cross runner 0.3 mm thickof section 24 mmx25 mm,wall angle shall be 0.63 mm thick of section 24 mmx24 mm grid shall be suspended by 4 mm dia adjustable quick fit hanger rod ,system exposed portion shall be pre painted polyster coated in off white/white in colour complete with material,fixing, jointing etc all as per manufactures instructions complete all as specified and directed. (Make:- Armstrong or of equivalent make as approved by GE).

Supplied and fixed fibre cement coloured textured designer ceiling board 4mm thick of size 595x595 mm conforming to IS : 14862 & IS : 2380 Part-XIV fixed to timber / GI / Aluminium frame work with screws/clips complete all as per manufactures instructions and as directed. (Make:- Armstrong or of equivalent make as approved by GE).

S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected commom rafters and running rails and guides for sliding doors, fixed with single cleats or other connecting plates conforming to Fe-400 Gde E-165 complete all as specified and directed.

M&L for preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide complete all as specified and directed.

M&L stone slab (Red stone) 50 mm thick cement mortar 1:4 dressed true and square, in one length not less than 60 cm and n.exc 120cm in copings, window cills, chajjas, sunshades, etc, punched dressed on exposed faces and self faced on the embedded unexposed beds and joints; exposed edges round or chamfered and making good in cement mortar 1:4 filling of edges of walls and joints of stone all as directed, set, jointed and pointed in mortar as in plinth protection complete all as specified and directed.

M&L cement concrete 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in coping including weathering, slightly rounded or chamfered angle and throating complete all as specified and directed.

M&L rendering 15mm thick on fair faces of brick work or concrete surface in CM 1:6, surface finsihed even and smooth without using extra cement complete all as specified and directed.

M&L for applying 15mm thick rendering using ready mix plaster bags in CM 1:4 on brick/concrete surfaces of external walls finished even and fair, using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, complete all as specified. Make: Ultratechrediplast, Brila Aerocon. Note:- Supply only water proofing compound shall be measured and paid separately. (Note: Contractor is required to deposit ready mix bags for 100% CA quantity to the Engr-in-Charge, within 15 days of acceptance of contract.

M&L for preparation of new plastered surface of wall by applying 2mm thick wall care putty (JK/Birla White) and making the surface smooth and applying two coats of Acrylic Exterior Emulsion paint over one coat of primer using roller for painting complete all as specified and directed.

M&L for preparation of complete removal of existing treatment from old plastered surfaces of wall by applying 2mm thick wall care putty (JK/ Birla White) and making the surface smooth and applying two coats of Acrylic Exterior Emulsion paint over one coat of primer using roller for painting complete all as specified and directed.

M&L for preparation of new plastered surface of wall by applying 2mm thick wall care putty (JK/Birla White) and making the surface smooth and applying two coats of oil emulsion distemper over one coat of primer using roller for painting complete all as specified and directed.

M&L for preparation of old surface after complete removal of existing treatment by mechanical means and applying 2mm thick wall care putty (JK/ Birla White) over one coat of primer and making the surface smooth and applying two coats of oil emulsion distemper using roller for painting complete all as specified and directed.

M&L PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate, 40mm thick, and applying layer of doctor fixit over the PCC surface complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) exc 1.5 Sqm & not exceeding 4 Sqm each complete all as specified and directed.

S&F for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges and door fittings necessary rivetting/welding cutting up complete steel conf to Fe-410-0 or gde E-250 complete all as specified and directed.

S&F for factory made 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, length of bolt in mm 300. complete all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F stainless steel butt hinges, medium weight, cold rolled, mild steel of size 100 mm including necessary stainless steel screws complete all as specified and directed.

S&F 200mm mild steel barrel tower bolts, stove enamelled black with bright bolt and nut complete all as specified and directed.

S&F 150mm mild steel pressed handles, oval type stove enamelled black complete all as specified and directed.

S&F 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel spring complete all as specified and directed.

Supply only liquid integral water proofing compound.

S&F 35mm thick, second class hard wood in glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

Eco- 4000 Series Ventilators/ Windows : M&L for Providing and fixing Windows, Ventilators fabricated from roll formed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality,Galvanized as per IS 277 with Zinc of 120 grams/ Sqr. Mtr.) with total coated thickness of 0.60 mm Paint specifications : Coated Sections should be coated with Primer Coat of Epoxy Primer of 5-7 microns thick, finish painted with Polyester paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns, or Powder Coated with pure Polyester Powder up to 50-60 microns thick. Dimensions of Sections : Sections for Frame should be of 72mm X 50mm, Section for Mullion should be of 72mmX50mm, Section for Shutter Frame should be of 47mm X 20mm, Section for Fixed Glass Bead should be of 12mmX12mm, and Section for Fly mesh should be of 40mm X 20mm. Fixing Details : Section for Frame Glazed Shutters and Mesh Shutters should be cut to length and miter joined with Polypropylene Corner Brackets, Mullion Section should be joined to the Frame/ Mullion using Nylon cap. Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass in shutter and Fixed Glass. Rubber Gasket should be used around Fly mesh to fix Mesh in Mesh Shutter. Accessories : Each Glazed Shutter should be provided with S.S. Pivot Hinges-1set, Seccolor Handle &Seccolor Stay. Glass : Glazed Shutter and Fixed Glass portions should be provided with a glass of 4/5mm Plain Float Glass.

Mesh : Mesh Shutter should be provided with a Stainless Steel 32 gauge Fly mesh of 304 grade with 144 holes per sq. Inch. Windows should be provided with Grill made of 10mm sq. MS Bars welded to at 150mm centre-to-centre, 6mm X 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws. Window Frame should be fixed to brick/concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames. Note. The item includes everything as, painting the surfaces, fixing, all necessary accessories, glass, mesh, etc, all as per given specifications, complete all as specified and directed by GE. Make - Bharat Win Solutions or equivalent makes as approved by GE.

S&F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dove-tailed or welded complete all as specified and directed.

S&F framed work such as grill framed for fixing arrangement for wire cloth etc complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staple complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Taking down chowkats or frame (without taking off shutters from the frame) area not exceeding 1.50 Sqm each complete all as specified and directed.

M&L screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 complete all as specified and directed.

M&L screed bed or bedding layer of mortar 10mm thick for laying floor finishes in CM 1:4 as backing coat complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurrty mixed with pigment to match the shade of slab including rubbing and beeswax polishing to receive granite finish complete all as specified and directed.

M&L kota stone slab 20-25 mm thick in riser of steps/skirting/dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed.

M&L machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658- 2006 of 80mm thickness, M-35 grade with grey cement and pigment over and including 50mm thick river sand cusion and apcking the edges/sides of the blocks with PCC 1:2:4 complete all as specified and directed.

M&L 75mm thick cement concrete type C-2, 1:3:6 (40mm grade agg) as in sub base complete all as specified and directed.

All as per item No 45.00 above but 150mm thick complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks of capacity 500 Litres (Cylendrical vertical with closed top), triple layer, white reflective colour, hoisted and fixed in position all as specified in SSR-Part-I including disconnecting and removal of old U/S PVC tank, complete all as specified and directed. Make:- Tuff, Sintex neo, Plasto.

S&F in repairs 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) complete all as specified and directed.

S&F in repairs, 15mm brass chromium plated fancy type bib cock with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make – PRAYAG CASA - Cat Part No-9206, CERA OCEAN Cat Part No – QTF2006151 HTF3001151, Pearl Cat Part No TTS-1060.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

S&F CPVC water tubes, medium grade, incl all necessary CPVC fittings, as per site requirement like elbow, tee, nipple, socket, union etc and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed. Make - PRAYAG, Finolex, Kisan.

S&F CPVC water tubes, medium grade, including all necessary CPVC fittings, as per site requirement like elbow, tee, nipple, socket, union etc and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed. Make - PRAYAG, Finolex, Kisan.

S&F 25mm dia, powder coated, fancy type, aluminium decorative tubular curtain rod with decorative ball type side brackets, complete all as specified and directed.

Excavation in trenches, not exc1.5m wide and not exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) in foundation filling and mass concrete complete all as specified and directed.

Removing excavated soil n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and directed.

M&L flat form work to sides of concrete foundations , footing bases of columns, raft and raft beams, sides and soofits (if any) of foundation and plinth beams and similar work, vertical or to batter rough finished surface of concrete complete all as specified and directed.

M&L form work to sides of pillars posts, struts piers, columns & stanchions square rectangular or polygnal fair finished surfaces in shape complete all as specified and directed.

M&L mild steel TMT bars 10mm dia & over cut to length, bent to shape required including cranking bending spirally for hooping for column, hooking ends & binding with & including mild steel wire (annealed) (not less than 0.9 mm dia) or securing with clips quality conforming complete all as specified and directed.

M&L TMT bars 6mm dia to 8mm dia in stirrups spacers & binders complete all as specified and directed.

M&L RCC M-25 (20mm graded aggregate) for founadtion including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed.

M&L RCC M-25 (20mm graded aggregate) for columns, pillars, pierrs, posts & struts etc complete all as specified and directed.

M&L moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L hardcore of gauge exc 63mm but not exc 100mm, depositd, soread and levelled in layers not exc 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

S&F rolled mil steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc including notching, drilling, fittings, riveting and or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing fittings angle cleats fish plates , gusset plates etc, also for wedging, plumbing , truing up and fixing conforming to Fe-400 Gde E-165 quality A complete all as specified and directed.

M&L 75mm thick cement concrete type C-2, 1:3:6 type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and directed.

Taking down carefully any type, battens or conduit point wiring with or except conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, pendent light fittings, MCBs / isolators, fan regulators, tube light fittings etc removing material from site and making good disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as specified & directed.

M&L for point wiring with 1.5 Sq mm (nominal cross section area) single core, 1100 volts grade, stranded, FRLS PVC insulated, unsheathed copper conductor in and including in PVC concealed conduit of any size/dia complete with all accessories/fittings, brass screws, washers etc sunk zinc coated pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover concealed in wall with and including continous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded copper conductor cable, unsheathed and connected to common earth and earth dolly and making good the disturbed area to match with the existing surfaces complete all as specified and directed for the following :- Make for conduit:- AKG/Plaza/Polycab/Kalinga

One light/tube light/bulb/fan/Bell point controlled by one, one way switch 05/06 Amps.

One 3 pin 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 amp switch.

One 3 pin 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 amp switch.

All as per serial item No 70.02 above but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15/16 Amps socket outlet point on independent board.

S&F switch piano flush button type, 5/6 Amps single pole, one way 240 volts complete all as specified and directed.

S&F in socket outlet 5 pin, 05/06 Amps flush type 240 volts complete all as specified and directed.

S&F in socket outlet 3 pin, 05/06 Amps and 3 pin 15/16 Amps (2 in 1 multipurpose) 240 volts complete all as specified and directed.

S&F switch piano flush button type, 15/16 Amps single pole, one way 240 volts complete all as specified and directed.

S&F bell push flush type, 5 Amps, 240 volts complete all as specified and directed.

S&F bell , AC, 230 volts, single poler Cona/Anchor complete all as specified and directed.

S&F stepped type electronic fan regulator flush type 230volts complete all as specified and directed.

S&F lamp holder (Angular/Striaght), insulated body, with back plate complete all as specified and directed.

S&F LED lamp 9/10 watt complete all as specified and directed.

S&F LED light fiting 1x22/25 watt 220V, AC decorative box typ with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing 1x36/40W LED Building security light energy saving & environmental friendly long life luminaire with high power LEDs as light source and electronic driver including security brackets of 32 mm dia GI pipe medium grade upto 1.2m long bend or shape at 100-200 degree including flat iron clamps and suitable nuts and bolts grouted in wall including all material required for fitting complete all as specified and directed. Make cat ref - SLE UL 40W IP66 (LXN) of Surya or equivalent in Philips/Havells/Crompton.

S&F luminaire 600mmx600mm 35/36 watt, 220V AC recessed type suitable for false ceiling complete all as specified and directed.

Supply & fixing of ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified and directed.

M&L for sub main wiring with 06 Sq mm (nominal cross section area) two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed copper conductor cable with and including continuous earth wire of size 6 Sqmm nominal roll cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25mm dia, medium grade with all conduit accessories/ fittings, brass screws, washers etc and connected to common earth dolly including all cutting/chases etc in wall, making good to walls etc including two coats of white/ colour washing/ distempering etc to the disturbed surfaces to match the exisiting complete all as specified and directed.

S&F sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amps rated copper bus bar and IP-43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempring etc to match the existing disturbed surfaces complete all as specified and directed.

S&F sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 4 way, with 200 Amps rated copper bus bar and IP-43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempring etc to match the existing disturbed surfaces complete all as specified and directed.

S&F MCB, SP, AC, 240 volts 'C' curve capacity of 06 to 32 Amps, 10kA and making connections complete all as specified and directed.

S&F MCB, SPN, AC, 240 volts 'C' curve capacity of 40 to 63 Amps, 10kA and making connections complete all as specified and directed.

S&F 415 V, 25KA, 4 pole MCCB, capacity 100 Amps and making connections complete all as specified and directed.

S&F exhaust fan steel body AC single phase 230V of size 300mm sweep with blades and frame and louvers complete all as specified and directed.

S&F vertical loadline sheet metal enclosure double door, triple pole and neutral (TP&N vertical loadline) AC, 415 volts, 04 way, with 200 Amps rated copper bus bar and IP - 43 & IK 09 protection, with provision of 25kA 100 Amp GI frame MCCB. Make - Legrand/Schneider/ABB/Indoaisian/Havells/C&S with the inbuilt provision for fixing of 1 No MCCB and 12 Nos MCB's inside of DB, with metal door and flush to wall including grouting and cutting in existing wall and making good disturbed surface with two coats of white/colour washing/distempering etc to match the existing one complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No 03 of SSR part-I connecting to main switch board/ Main DB's including exacavtion, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm centre to centre both way with suitable lifting handle and pit/ chamber in PCC 1:3:6 type C1, Angle iron 40x40x5mm frame for pit cover including testing on completion, complete all as specified and directed.

Supply, laying in trenches or fixed to wall/pole, XLPE insulator, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts, grade laid in trenches/fixed in wall/pole of cross sectional area of cable 50 Sqmm 3.5 core complete all as specified and directed.

Excavation in trenches, not exc 1.5m wide and not exc 1.5m in depth for foundations etc or for laying of cable or Pipe, electric pole, stay assembly etc not exc 10 sqm on plan and not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exc 25 cm thick in soft/loose soil complete all as specified and directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Supply and spreading clean fine dry river sand in trenches for cushioning of under ground cable/cable duct or inside the premises of transformer yard complete all as specified and directed. (Note: Only Punned thickness shall be measured for the purpose of paymnet).

M&L for laying burnt clay fly ash old size bricks, straight or curved on plan, laid flat with width equal to length of brick, laid dry over under ground cable for protection complete all as specified and directed.

M&L for galvanised steel tubing, light grade with all fittings for protection of cable including taking own old, rusted & corroded unsv Galvanized steel tubing and 40mm size complete all as specified and directed.

Arun Construction Co.

MOHAN LAL GUPTA

Shikhar ji Enterprises

SA construction co.