Special Repair To OR Md Accn Bldg No. P-58/1 To 10 And Offrs Mess Kitchen Bldg No P- 213 In KLP II At Military Station Fazilka

Amount

SCHEDULE 'A' SECTION I (B&R Portion)

Taking down chowkats with shutters (without taking off shutters from the frame exceeding 1.50 sqm each but not exceeding 4 sqm) removing to store

Taking down chowkats or frame with shutters(without taking off shutters from the frame not exceeding 1.50 sqm each & removing to store all as specified.

S&F PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification and designs

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S & F 125 mm long aluminium handle cast type anodized.

S & F 125 mm long aluminium anodised barrel tower bolt of extended section and fixed.

S & F 100 mm long butt hinges extruded alumiunium alloy with galvanised mild steel hinges pin, anodised and fixed.

Taking down shutters and Refixing of shutters of any description exceeding 1.00 Sqm and n. exc.2.00 sqm each in the same opening complete all as specified and directed by Engineer-in-Charge.

M & L for Pieces, small let in for making good where hinges, etc. have been removed from chowkhals or frames, joinery, etc. including painting or oiling to match, if required complete all as specified and directed by Engineer-in-Charge.

S & F pressed steel door frames with one or more rebates including necessary fixing lungs hinges lock strike plate etc complete all as specified size of frame 125 x 60mm all as specified.

S & F pressed steel door frames with one or more rebates including necessary fixing lungs hinges lock strike plate etc complete all as specified size of frame 105 x 60mm all as specified.

All as per above here in before but for size 75x60mm as in cup board frames complete all as specified and directed by Engineer-in-Charge.d.

M&L Cement concrete 1:2:4 type B–1 filling of pressed steel frame and hold fast blocks etc all as specified.

M & L block boards 19 / 20mm thick, grade 2 quality, interior grade, decorative type with decorative face veneer on one face, fixed with screws to timber as in pelmet/shelves frame work with teakwood lipping 6 mm thick or fixed with screws to Pressed steel frame work complete all as specified and directed .

S & F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats complete all as specified and directed

S & F Flush shutters,35mm thick,solid core construction,with block board core and plywood face panels,commercial type on both sides as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats complete all as specified and directed by Engineer-in-Charge.

S & F Aluminium, anodised, barrel tower bolts 150mm long of extruded section all as specified and directed.

S&F Aluminium handles 150mm size, cast type, anodised all as specified and directed.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixe.

S & F in repair MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,150 mm fixed in floor all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, anodised aluminium frame for doors, window, ventilators with one or more rebate including joining cleat for fixing etc complete all as specified and directed

S&F in repairs, anodised aluminium window/ventilator shutter side hug type without sash bar aluminium section wt 0.55 kg/mtr including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screw anodised aluminium fitting such as peg complete all as specified and directed

S&F aluminum anodized grill diamond shape 100mm x 100mm aperture of 6 mm dia round bars including necessary joining cleats, clips anodised complete all as specified

S & F in repair aluminium window rescuring or easing and adjusting without taking down shutter any description exc 1.00 sqm but not exc 2.00 sqm each complete all as specified and directed

Taking down and refixing of aluminium window shutter of any size insame opening incl repairs/replacement of rubber packing glass clips & aluminium section ect complete all as specified and directed by Engineer-in-Charge. Note : The item glass glazing clip & aluminium section will be measured separately

S&F galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width or aperture 1.18mm all as specified and directed.

M & L for preparation of new wooden of wooden based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

M & L for preparation of old painted wooden surfaces of any description over 10 cm width of girth not otherwise described and applying one coat of synthetic enamel paint all as specified.

Taking down cement or cement lime plaster from brick walls etc including raking out joints, hacking for key scrubbing down with water etc.

M & L for rendering 15mm thik on fair faces of brick work in cement mortar 1:6 finished even & smooth without using extra cement.

M & L for rendering 15mm thik on fair faces of brick work in cement mortar 1:4 finished even & smooth without using extra cement.

M&L rendering 10 mm thick in cement mortar 1:3 om fair faces of concrete surfaces of ceiling finishing even and smooth without using extra cement.

Supply only liqid water proofing compound.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L glazed ceramic tiles 450X 300X 7mm colour tiles on walls etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the work over 10 mm rendering in CM 1:4.all as specified.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry to match the work using colour tiles over screed bed on bedding layer of mortar 15mm thick is CM 1:6.all as specified.

M&L Granite (of any type) tiles 18mm - 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 20mm thick rendering in CM 1:4, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L marble work 18 to 20 mm thick in single piece (table rubbed and polished) in steps, jams, pillars, windowcills,cooking platforms and like in cement mortor (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade as approved complete all as specified and directed

M&L marble work 18 to 20 mm thick in single piece in riser of steps, skirting , dado, and pillar laid and jointed in cement mortor (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade as approved complete all as specified and directed

Dismantling of brick wk built in cement mortar

M&L brick work with fly ash modular bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6

Formwork to chullah hoods, chajjas, troughs and similar items including edges all as specified and directed.

M & L RCC 1:1½:3, (nominal mix), type A-1, using 20mm graded aggregates as in Chajjas including TMT bars welded with existing steel complete all as specified and directed

Demolation of cement concrete ( Re-inforced) of any description in ground floor and pavings Nexc15 cm thickness (below or above GL)

M&L for reinforcement 10mm and over, cut to length , bent to shape required , including cranking , benching sprirally for hooping for columns , hooking ends and binding witjh and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quantity confirming to IS all as specified.

Formwork to soffits of suspended slabs such as roof slabs , floor slabs , landing and similar work exceeding 200mm thick all as specified

M&L for RCC (nominal mix) 1:2:4 using 20mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landing , balconies, canopies, deck slabs and in shelves and the like all as specified and directed.

Dismantling water tanks and removing to store of 500 ltr capacity

S & F rotational moulded polythene three layered white coloured water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 500 Litres all as specified.

S&F 20 mm float ball valve high pressire of PTMT with epoxy coated aluminium rod & high density platic ball screwed for iron pipe and fixed. ( Min weight 15 mm - 142 gms/20 mm 210 gms/25 mm 455gms/40mm 690 gms)

S & F Vitreous china white, flat back, wash basin of size 550 x 400 mm including brackets, waste pipe and waste fitting 40 mm brass chromium plated and waste pipe and 15 mm dia PVC connection with brass nuts as in repairs complete all as specified and as directed.

S&F Vitreous china squatting pan, Orissa Pattern size 580mm x 440 white with integral foot rest and ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe including placing in position and embedded lean/lime concrete bedding, all as specified.

S&F PVC 10 ltr syphonic action type flushing cistern, loe level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32 mm bore and connection to WC pan complted all as specified.

S&F grating square 100 mm dize of PTMT (minimum weight 25 gms)

Taking up or down steel tubing of 15 mm bore and connections, including cleaning for re-fixing or removal to store

Supplying and laying of CPVC pipes 20mm OD SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

Taking up or down steel tubing of 20 mm bore and connections, including cleaning for re-fixing or removal to store

Supply & fixing mild steel tubes of size 20 mm bore (medium grade) galvanised with all fittingsand fixed complete to wall all as specified.

Taking up or down steel tubing of 25 mm bore and connections, including cleaning for re-fixing or removal to store

Supply & fixing mild steel tubes of size 25 mm bore (medium grade) galvanised with all fittingsand fixed complete to wall all as specified.

S&F in repair stop cock/gate valve cast copper alloy screwed down, high pressure, with crutch of butterfly handle screwed both ends to iron pipe of size 20mm.

S&F in repair stop cock/gate valve cast copper alloy screwed down, high pressure, with crutch of butterfly handle screwed both ends to iron pipe of size 25mm.

Demolation of ashlar facings, dressed stone work, stone slabs or tiles from paving and precast concrete blocks and articles complete all as specified and directed

M&L for PCC (1:5:10) using 40 mm grageded burn brick aggregate as in foundation, filling & mass concrete or filling in sunken floor complete all as specified and directed.

M&L for Water proofing treatment to RCC sunken slab (not exceeding 45cm depth of sunken) as specified below complete all as specified and directed by Engineer-in-Charge. :- (a) applying 15 mm plaster in CM 1:3 with WPC on raised verticle surface (b) Cleaning the surface with wire brush/coir brush, removing lose material like dust particles, dirt etc. (c) Creating fillet coving of 50x50 mm with polymer modified mortar on the junction of slab and walls (d) Apply first coat of two component modified polymer coating on the horizontal and verticle surface (e) Provision of glass fiber mesh of 2 x 2 mm immediately on above coating (f) Apply second coat of two component modified polymer coating after 72 hrs (g) Cement concrete 1:4:8 over the coating as per requirment (h) Joining the saintary pipes with the water proofing tape having bridging ability of more than 1.5 mm (j) Filling the gap between the wall opening and saintary pipe with non shrink cementatious grout complete as specified.Plan area shall be measured

Tacking down eaves gutters and ran water pipes

Dismantling of CI pips or reinforced concrete pipes 100 mm dia fixed to wall etc complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall all as specified and directed.

S&F PVC (SWR) bends 110 radius complete all specified and directed.

S&F PVC (SWR) branch piece,single (single Y) 110 mm redius complete all specified and directed.

S&F PVC (SWR) branch piece,Single (sngle Y) 110 mm redius complete all specified and directed.

Dismantling of CI pips or reinforced concrete pipes 75 mm dia fixed to wall etc complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall all as specified and directed.

S&F PVC (SWR) bends 75 radius complete all specified and directed.

S&F PVC (SWR) floor trap 100 mm bore with grating including jointing to waste pipe and fixed with PCC 1:2:4 complete.

S&F PVC (SWR) branch piece,single (single Y) 75 mm redius complete all specified and directed.

S&F PVC (SWR) vent cowl 75 mm redius complete all specified and directed.

S&F PVC (SWR) floor trap 75 mm bore with grating including jointing to waste pipe and fixed with PCC 1:2:4

S&F in repair bib taps cast copper alloy screwed down crutch or buttefly handle screwed both ends for iron pipe brass ferrrule of size 15mm bore.

S&F in repairs 15mm stop valves fancy type, chromium plated with long shank and cup (concealed type) , cast copper alloy complete.

S&F 15 mm bore CP angle cock one way chromium plated, high pressure with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified.

S & F in repair brass chromium plated central hole basin mixer with regular spout , popup waste system and 450mm long braided hoses with connection and nuts complete all as specified and directed by Engr-in-charge.

S & F brass chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe and fixed. Make : Prayag.Essco and equivalent.

S & F stainless steel sink made of 1 mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortor on dwarf wall or including fixing in counter and connecteing union to pipe overall size 495 mm x 420 mm boel size 410 x 330mm x 160 mm complete all as specified and directed

S & F in repairs, Sink mixer with swinging spout ( wall mounted model) Chromium plated brass with connection and nuts complete all as specified and directed by Engineer-in-Charge. Make - ESSESS Cat part No- DE-12 or equivalent to Parryware / Nirali / Prayag.

S & F in repair stainless steel plate rack of size of 900 mm x 775 mm x 250 mm made out of 1 mm thick stainless steel of first quality complete all as specified and directed by Engineer-in-Charge. Make Anupam international Model No KPR - 311 or Equivalent make and model approved by GE.

S&F in repair towel rail 20mm dia, D type 60cm long between flanges brass bran chromium plated. Make -hindware. Esser etc equialant.

S & F in repairs, soap dish chromium plated brass complete all as specified and directed by Engineer-in-Charge.

S&F PVC waste pipe 32mm dia & 90 cm long Complete all as specified and directed.

S&F PVC connection both side brass unions internal for size 15mm dia and 450mm long all as specified.

S & F Waste coupling for 40 mm bore dia. of discharge pipe PTMT (half or full threaded) . Minimum weight 45 gms.

M&L 50mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in plinth protection, surface finished even smooth without using extra cement.

Preparation of newly plastered surface of wall and applying two coats of cement base paint. Complete all as specified and directed.

Complete removal of old existing treatment on walls and applying two coat of cement base paint including preparation of surface complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new plastered surfaces applying three coats of white wash on Wall Surfaces complete all as specified and directed.

M&L preparation of old plastered surfaces applying three coats of white wash on Wall Surfaces complete all as specified and directed.

M&L preparation of New plastered surfaces applying three coats of white wash on ceiling. Complete all as specified and directed.

M&L preparation of old plastered surfaces applying two coats of white wash on ceiling. Complete all as specified and directed.

M & L Preparation of newly plastered surfaces by applying two coats of interior grade wall putty and making it smooth with sand paper by mechanical method i.e. with hand electric grinder and applying two coats of oil bound distemper over one coat of cement primer including all as specified by mechanical method i.e. spray gun complete all as specified and directed

M & L Preparation of Old plastered surfaces by removing old treatment and applying two coats of interior grade wall putty and making it smooth with sand paper by mechanical method i.e. with hand electric grinder then applying two coats of oil bound distemper over one coat of cement primer including all as specified by mechanical method i.e. spray gun complete all as specified and directed by Engineer-in-Charge.

Dismantling of brick tiles or terracing tiles,single layer on roofs including cement motor complete all as specified and directed by Engineer-in-Charge.

Dismantling of mud in roofs,any thickness,including plastering and leeping (Whether full thickness removed or only a part thereof) complete all as specified and directed by Engineer-in-Charge.

Removal of mud to a distance exceeding 250m and n exc. 500m and depositing where directed complete all as specified and directed by Engineer-in-Charge.

M&L cement concrete flooring type B0 1:2:4 using 12.5mm graded aggregate on roof slab.

M & L rendering 15mm thick water proofing plaster in CM 1:3 on slab / roof admixed including and with Dr. Fixit pidilite LW+@ 200 ml per bag of cement complete all as specified and directed

Providing and applying microfiber reinforced UV resistant acrylic polymer coating three coats having solid contents 69% polymer content 35% & tensile strength 2.6 N/mm2 of Dr. Fixit newcoat /stat/parex/Asianpaints or equivalent with a paint brush over existing roof surface after removal of all loose material lime dust etc with wire brushes from roof surfaces to get absolutely cleaned surface free of foreign contaiminantf flling of cracks wherever found with polymer based mortar, and after refairing the surface apply primer coat with Dr. Fixit prime seal polyester reinforced fiber net laid on the surface repair before executing the water proofing treatment complete all as specified and as directed by Engineer-in-charge. Note : The treatment shall be carried out by authorised applicator approved by CWE as per the manufacturer instructions complete all as specified and directed by Engineer-in-Charge.

M & L Endura Cool roof tiles 300 x 300 x 10 mm white vitrified water absorption < 0.5% SRI >90 (ASTME 1980, EN673 and En 411) BEPL (Building energy performance laboratory ) certified laid over screed bed or bedding layer of mortar 15 mm thick CM (1:4) complete all as specified and directed by Engineer-in-Charge.

Excavation in post holes n exc 0.50m and getting out soft / loose soil complete all as specified and directed by Engineer-in-Charge.

S & F for framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') complete all as specified and directed by Engineer-in-Charge.

S & F for 4 mm dia GI wire fitted with nut and bolt complete all as specified and directed by Engineer-in-Charge.

M & L for preparationof new steel surface over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M & L for preparation of old painted steel surfaces of any description over 10 cm width of girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

S&F in repairs drapry curtain rod 25mm dia, fancy type, fabricated out of mild steel sheet not less than 20 guage, including brackets and pair of decorated end knobs (finials), stop roller etc, pretreated powder coated natural color complete all as specified and directed by Engineer-in-Charge.

M & L 75mm thick PCC 1:4:8 , type D- 2, using 40mm graded aggregate as in sub base all as specified and as directed.

S&F machine pressed precast concrete interlocking paver block with grey cement & no pigment, any shape and size confirming to IS 15658-2006 of 60mm thick M-40 grade including and over 25mm thick sand cushion.

M & L PCC 1:2:4, type B-1 , using 20mm graded stone aggregate as in kerbs or mud stops, rounded or chamfered on edges and similar work all as specified and as directed.

S & F Flush shutters, 25mm thick, solid core construction, with block board core and plywood face panels on both sides as per SSR Part – I all as specified.

M&L 18-20 mm thick block board ,grade 2 quality ,interior grade ,decorative type with decorative face veneer on one faces including wooden beeding around the edges of board ,fixed with screws on wall as racking work all as specified and directed by GE.

S & F continous (Piano)type hinges mild steel bright finish or lectro galvanised with wide of flaps 30mm complete all as spd and directed.

Providing kitchen cabinet in required sizes at site made out of 18 mm thick one sided decorative lamination & other side balancing lamination sheet consisting of carcass 18 mm thick PVC sheet & provision of shutters made out of 18mm thick one sided decorative laminated PVC sheet all required brackets SS screws etc. the panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as per drawing and specification approved by GE. Make : Rajshri & Equivalent

S & F 75mm size stainless steel bright finish handle, fancy type for cupboard shutter all as specified and directed by Engineer-in-Charge.

S&F Stainless steel tower bolt 150mm long heavy duty all as specified and directed by Engineer - in - Charge.

S&F aluminium anodised barrel tower bolt 200mm long

S&F Aluminium pressed handles oval type 150mm size

M&L preparation of new steel surface over 10 cm width or girth and applying two coat of synthetic enamel paint.

M & L applying three coat of white wash on newly plastered or unplastered ceiling surfaces including preperation of surfaces, complete all as specified.

M & L Preparation of newly plastered surfaces by applying two coats of interior grade wall putty and making it smooth with sand paper or with hand electric grinder then applying two coats of oil bound distemper over one coat of cement primer all as specified and directed.

M & L Preparation of Old plastered surfaces by removing old treatment with sand paper or hand electric grinder and applying two coats of interior grade wall putty and making it smooth with sand paper or with hand electric grinder then applying two coats of oil bound distemper over one coat of cement primer all as specified and directed.

M & L for complete removal of existing treatment and applying two coats of white wash on old decorated plastered or unplastered surfaces of ceiling including preparation of surfaces complete all as specified and directed by Engineer - in - Charge .

M & L for complete removal of existing treatment and applying two coats of white wash on old decorated plastered or unplastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in - Charge .

M & L applying three coat of white wash on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified.

M & L Complete removal of old existing treatment on walls and applying two coat of cement base paint including preparation of surface complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete in ground floor and paving n.exc 15 cm below or above ground level.

M&L cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate as in floors 25 mm thick for tiles all as specified.& directed by Engineer -in-charge..

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement mixed with pgment to match the shade of the slab including rubbing and polishing complete inculding screed bed or bedding layer of mortar 15 mm thick CM (1:6)all as directed by Engineer-in-Charge.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base in riser of steps, skirting, dado and pillar laid and jointed with grey cement mixed with pgment to match the shade of the slab including rubbing and polishing complete inculding screed bed or bedding layer of mortar 15 mm thick CM (1:6)all as directed by Engineer-in-Charge.

Dismantling water tanks and removing to store of 1000 ltr capacity.

S & F rotational moulded polythene three layered white coloured water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 1000 Litres all as specified.Make -

Disconnecting existing tank setting aside or lowering if required for repairs, cleaning etc and hoisting if required reconnecting and refixing in position (cleaning repairing etc measured separately), exc 250 Ltrs and n.exc. 500 Ltrs capacity.

Disconnecting existing tank setting aside or lowering if required for repairs, cleaning etc and hoisting if required reconnecting and refixing in position (cleaning repairing etc measured separately), exc 500 Ltrs and n.exc. 1000 Ltrs capacity.

S&F in repairs 20 mm float ball valve high pressire of PTMT with epoxy coated aluminium rod & high density platic ball screwed for iron pipe and fixed. ( Min weight 15 mm - 142 gms/20 mm 210 gms/25 mm 455gms/40mm 690 gms)

S&F 15 mm bore CP angle cock one way chromium plated, high pressure with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified.

Taking up or down steel tubing of 15 mm bore and connections, including cleaning for re-fixing or removal to store

Taking up or down steel tubing of 20 mm bore and connections, including cleaning for re-fixing or removal to store

S&F chlorinated PVC (CPVC) pipes 20 mm outer dia, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.0 m spacing . this includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete all as specified and directed. Make : Supreme/Vectus

S & F in repairs for brass chromium plated shower rose 125 mm size with swivel joint including fixing to 15 mm dia steel pipe or union.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in loose / soft soil.

S&F in repairs door closer hydraulically regulated, aluminium (Die cast) body, designation No. 3, universal type suitable for door shutter upto 1000mm in width complete all as specified and as directed by Engineer-in-Charge.

S&F anodized aluminium frame with Powder Coating (minimum thickness of powder coating 50 micron) for doors, windows, ventilators, partitions etc., with one or more rebates including joining cleat for fixing etc complete all as specified and as directed

S & F in repair powder coated aluminum sliding window three track with frame & two glass shutter using 4 mm thick glass tinted modi guard and one shutter with stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperture 1.61 mm using aluminum powder coated section aluminum cleat , PVC track, bearing, handle lock rubber beading etc complete fittings as approved. Note :- Size of aluminum section shall be under – (i) three track top and vertical – jindal main 2010. Section No 20621 or equivalent as approved by GE. (ii) Three track bottom – Jindal main – 2010 section 20620 or equivalent as approved by GE. (iii) Shutter Vertical Section - Jindal main – 2010 section 20604 or equivalent as approved by GE. (iv) Shutter top and bottom - Jindal main – 2010 section 20604 or equivalent as approved by GE. (v) Shutter vertical middle ( interlock) - Jindal main – 2010 section 20605 or equivalent as approved by GE.

S&F powder coated aluminum windows and ventilators shutter side hung type without sash, aluminum section weighing glazed clips, rubber packing anodized aluminum fittings such as peg stays 150 mm long (1 nos) hinges type B-21 100 mm long (2 Nos) suitable handle (1 Nos) complete all as specified.

S&F aluminum anodized grill diamond shape 100mm x 100mm aperture of 6 mm dia round bars including necessary joining cleats, clips anodised complete all as specified

S&F in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanesed wire stapels complete all as specifed and directed.

S&F PVC connection both side brass unions internal for size 15mm dia and 450mm long all as specified.

S & F in repair brass chromium plated central hole basin mixer with regular spout , popup waste system and 450mm long braided hoses with connection and nuts complete all as specified and directed by Engr-in-charge.

S&F in repairs gun metal globe or gate valve with crutch or butterfly handle screwed both ends for iron pipe of 15 mm dia all as directed.

S&F in reapirs gun metal globe or gate valve with crutch or butterfly handle screwed both ends for iron pipe of 20 mm dia all as directed.

S&F gun metal globe or gate valve with crutch or butterfly handle screwed both ends for iron pipe of 15 mm dia all as directed.

S&F gun metal globe or gate valve with crutch or butterfly handle screwed both ends for iron pipe of 20 mm dia all as directed.

S&F Cast iron floor trap 100 mm bore with grating including jointing to waste pipe and fixed with PCC 1:2:4 all as specified and directed by engineer-in-charge.

Taking down eves and gutter and rain water of any size all as specified and directed by Engineer - in - Charge .

Hacking out old broken glass (any size,thickness,quality or description from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified & directed by Engineer -in-charge.

S & F in repairs 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane all as specified and directed by Engineer - in-Charge.

S&F 100 mm size hasp and staple,safety type,Stainless steel bright finish ,including bolt to hinge plate and fixed with screws,complete all as directed.

Resecuring the aluminium door shutter after tightening of members, refixing of glass panes, adjusting of door closure etc. of any description exc 1.00 sqm but not exc 2.0 Sqm each complete all as specified and directed by Engineer - in - Charge.

Refixing of shutter,in same opening of any description exc 1 Sqm and n exc 2 sqm each

M&L cement concrete flooring type B0 1:2:4 using 12.5mm graded aggregate on roof slab.

Preparation of roof top surfaces, providing and applying UV stable single component smart care damp proof ultra is a fibre reinforced elastomeric liquid applied water proofing membrane formulated with PU hybrid polymers and reinforcing acrylics fibres and having SRI of 106 on top of concrete roof surface in three coats including self primer at ratio pf damp proof and water 3:1 and coverage @ 1 Ltr /10 sqm with a thickness of 650micron Note: 6 Hrs interval between two coats will be maintain& the work will be carried out through company applcator duly got approved from Accepting officer in writing before incorporation and paid only after receiving of the warrenty certificate from the company. Make : Asian paint or equivalent as approved by GE

SCHEDULE 'A' SECTION-II (E&M PORTION)

Taking down carefully existing aluminium/Copper point wiring light, fan socket or power bell complete with fitting such as sockets, ceiling roses, pendants batten holders regulators socket, call bells & making good to the disturbed surfaces of walls, matching the colour with existing Surface all as spd and directed by Engr-in-Charge. Note: Rate for making good shall be deemed to be included in above item rate.

Taking down unserviceable main switches and MCB distribution boards single phase complete all as spd

M & L for point wiring complete with 1.5 Sqmm (Nominal area) PVC insulated multustranded fire retardant (low smoke unsheathed and multicore copper conductor cable with colour code ISI marked and including PVC concealed conduict ISI marked and conduit fittings for one light point/fan point/exhaust fan controlled by one switch including PVC insulated 1.5 Sqmm single core copper earth wire to common earth and connecting to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified (Cost of MS sunken box and bakelite sheet included in the rate).

All as above here-in-before but one three pin socket outlet 5 Amps on the independent board complete all as specified.

All asabove here-in-before but one three pin socket outlet 5 Amps on the same board complete all as specified.

M&L for point wiring complete with 2.5 Sqmm (Nominal area) PVC insulated multistranded fire retardant low smoke unsheated and stranded copper conductor cable ISI marked in and including PVC concealed conduit medium quality and conduit fitting for 3 pin 15 amp multicore switch socket combination including PVC insulated 2.5 Sqmm single core copper earth wire to common earth and connected to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified.

S&F switch Piano type single pole one way 5 Amp,230 VAC supply.

S&F socket two in one ,3 Pin 5 Amps 230 VAC supply, .

S&F switch Piano type single pole one way 15 Amp on laminated sheet top cover complete to all as spd (Sheet top cover incl in point wiring) .

S&F socket Pinao type 6 Pin 16 amp,230 VAC .

Supply & fixing PVC Lamp holder suitable for and including batten fittings ,LED Electric lamp 9 Watt with backalite 20mm back plate complete all as specified & directed, .

M&L for Ceiling Rose, surface bakelite 12 to 3 terminal, 240 volts, 5 Amp ISI marked complete all as specified and directed.

S&F of fan regulator step down electronic type heavy duly flush type 230 volts AC single phase fixed on laminated sheet top cover (laminated top cover is included in point wiring) and connecting up complete all as specified and directed. (Laminated sheet top cover and sunken box is included in point wiring).

S & F of MCB suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA and 6 to 32 Amps all as specified and directed.

S & F of MCB suitable for 240 volts AC supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA and 16 to 40 Amps all as specified and directed.

S&F Distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting SPN 8 way 240 volts with bus bar rating 200 Amps dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and directed..

S&F and testing LED light fitting 1x18watt 4 feet long including LED tube with driver complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any cracks or through h oles. The system wattage of fitting should not be more than 18 watt= 10%, surge protection of minimum 2 KV power factor should be more than 0.90 cool while colour, total hormonic distoration (THD) should not be more than 15% lumen output should not be less than 1700 lumens, total input voltage range 140-280V AC, colour rendering index should not be less than 80, Corelated colour should be minimum 6000 degree Kelvin.

M & L for Sub main wiring with 2 single core 6 Sqmm PVC insulated FRLS cable with multicore copper conductor drawn into and including PVC conduit rigid non metallic of suitable dia with and including independent PVC insulated one run 6 Sqmm single core copper earth wire complete all as specified. (Note:- Three lengths of 6 sqmm cable and will be measured as one length).

Taking down carefully, dismantling ceiling fan of any make sweep and size and reassembling after necessary repairs overhauling,greasing, oiling and replacement of worn out spares, sealing cable ends, dismantling blades, opening up for inspection and transportation to contractor’s workshop and back including hanging, fixing and connecting up and testing complete all as directed by Engineer-in-Charge. Note 1. Material and labour required for rewinding of fan motor shall be measured and paid for separately. 2. Spare parts where ever required for replacement shall be measured and paid for separately as supply only and fixing is including under this item.

Material & labour for rewinding of ceiling fan motor 1200/1400mm sweep with super enameled copper wire of existing specification, gauge and weight including insulating etc complete all as specified and as directed by Engineer-in-charge. Brand of copper wire -: Atlas / Devi Dyal/BPL

Supply and fixing only ball bearing of existing No. and size suitable for ceiling fan 1200 / 1400 mm sweep of any make including necessary greasing etc complete all as specified and as directed by Engineer-in-charge. Make: SKF/NBC

Supply and fixingonly Ceiling Fan Capacitor 3.15 MFD including necessary connections complete all as specified and as directed by Engineer-in-charge. Make : KELTRON / USHA / UNISTAR.

All as above here -in- before but Exhaust fan of size 220/250/300/380/450 mm sweep all as specified

Disconnecting electrical/mechanical connections and taking down existing u/s storage type water heater (Geyser) Capacity 50 ltrs of any make,type and size by unscrewing nuts,bolts,washers and transporting to store yard of MES at Fazilka(site of repairs) where necessary repairs to be carried out, opening up , inspecting the defects jointly by contractor or his rep and Engg-in-charge,making joint inventories of defects to be rectified and spared to be replaced , re-assembling after repairs and replacement of spares, transporting back to the location from where taken down and fixing in original position and making the water and electrical connections, testing and making functional ect complete all as specified and directed by Engr-in-Charge. Note:- Replacement of spare parts such as Inner assembly, inner tank, glass wool & outer body shall be measured and paid separately under respective items.

Supply and fixing MS outer cover as per existing thickness with nuts , bolts,clamps,brackets duly painted with two coats of synthetic enamel paint with spray gun over a coat of red oxide primer rubber clamps base plate,screws etc for storage type water heater of capacity 25 Ltrs all as specified and directed by Engr- in-Charge.

Supply and fixing geyser inner assembly of brass with inlet/outlet & over flow provision rubber washer suitable for 50 ltrs capacity all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement heating element 1500 watt of suitable shape and size,any specification, confirming to ISI with PVC rubber washer clamps type all as specified and directed by Engr-in- Charge. Make: Daspass/Recold/Bajaj

S&F in replacement of thermostat of size 0-90, thermostat switch suitable for storage type geyser all as specified and directed by Engr-in-charge, Make :Daspass/Denfoss/Bajaj

S&F PVC Connection 450 mm long 15 mm for cold pipe line

S&F PVC Connection 450 mm long 15 mm for cold pipe line

Material and Labour for fixing Electric Chimney Sunflame amaze DX Comes with dry heat auto clean system powerfull suction of 1100cum/hrs 3 speed touch sesor controll with digital display and timer 2 X 1.5 watt LED Light 11 digree tilted stainless steel Baffle filter with stain less steel oil collector . Size 60 CM .

S&F Electric bell ding dong complete all as spd

S&F bell push flush type 5 Amp, complete all as spd

Supply and fixing inner water storage tank made out of ultra thick stainless steel of superior 304 grade of existing size,type and make suitable for geyser of 25 Ltrs capacity etc complete all as specified and directed by Engr-in-Charge.Make: BAJAJ/HAVELLS/V GUARD/RACOLD/ORIENT

RUCHIKA CONSTRUCTIONS

HARSH CONSTRUCTION CO.

G S CONSTRUCTIONS