PROVIDING ILLUMINATION, HT LINE, SOUND SYSTEM AND STAGE LIGHT IN LARGE PARK OF SEC-24 U/E PANCHKULA (EXTENSION). (INCLUDING 5 YEARS FREE MTC./DEFECT LIABILITY PERIOD FREE OF COST).

Amount

Supply and Erection of Sensor based AMSON’s/ Indo Asian make automatic Electronic timer to Switch ON/OFF the street / Road light automatically. It will change switching ON/OFF timings automatically on daily basis throughout the year as per change in timing of sun rising and sun setting suitable for street/ Road lights. It will have three contractors of 24 Volt of BCH (Bhartiya Cutler Hammer) to control load upto 40 Amp. Per phase with voltage ratio @230/240. It will have light activated automatic Switching system to switch ON/OFF of the Road street lights. It will have Auto/ manual systems for maintenance of street light during day time. It should have Transformers with voltage ratio 230/240 and other allied accessories as required. Bakelite sheet to assemble the components etc. It should have Kit Kat of 20 Amps capacity to save the time switch from power fluctuation. The device will be housed in the existing pedestal/box/pole etc. in such a way so that it operates at correct timings and erection of the same at site complete in all respect upto the entire satisfaction of Engineer-In-Charge.

Supply and erection of 11 KV Lightening Arrestor (conforming to ISS:3070/1985) with latest amendments complete in respect and erection of the same upto the entire satisfaction of the Engineer-in-charge.

Supply and Erection of fuse unit L.T. side of 100/200 KVA Transformer complete with wooden board cleats, aluminium strips M.S. clamp and M.S. Nuts and Bolts including all petty material required upto the entire satisfaction of Engineer-In-Charge.

S/E of 11 KV disc fitting (Hardware) with accessories suitable for stringing and sagging of ACSR Conductor 50 Sqmm. Conforming to relevant IS specification with latest amendments complete in all respect upto the entire satisfaction of Engineer-In-Charge.

S/E of Disc Insulator without fitting T and C Type Jay Shree Make (Conforming to ISS:2486 Part-I and II) with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge.

S/E of 11 KV G.I. Pins (long) for H.T. line (Conforming to ISS 2486 (Part-I and II) with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge.

S/E of 11 KV Pin Insulator Brown Glazed with creepage distance with 230mm Jaya Shree Make (Conforming to ISS 73/1971) with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge.

S/E / Erection of V-Shape Cross Arm as per REC specification / Approved by UHBVN for H.T. line made out of M.S. Channel 40 x 75mm flange thickness 7.3mm holes thickness 4.4mm (conforming of relevant provided in the web at the base for fixing of half clamp and 2 Nos. 20mm for G.I. Pin on the flange of the top. The plate of M.S. flat 50 x 6mm shall be welded on the top and bottom flange of both end of V-shape cross arm with 22mm of holes in the plate complete in all respect upto the entire satisfaction of Engineer-In-Charge.

S/E of G.I Pipe earthing set 40mm dia 2.5 Mtr. long shall be of medium class conforming to ISS: 1239(Part-I) with latest endments shall have 12mm dia holes at interval of 150mm on the entire surface of the earthing pipe shall be tapered and top and of G.I pipe shall be threaded and shall be provided with suitable size of G.I earth wire. The clamp shall be tightened to the earth pipe with 12mm dia galvanized M.S. Nut and Bolts and spring washers complete in all respect upto entire satisfaction of Engineer-In-charge.

Supply and erection of Earthing Rod of 20mm dia and 2.5 Mtr. Long shall be tapered to be pointed at one end of about length of 50mm and other end of the rod shall flatten over a length of 150mm into 40mm and having two holes of 12mm dia and 50mm apart alongwith 16 SWG thick conduit pipe 25mm dia 3 Mtr. Long (conforming to IS 9537 (Part-I) enameled black painted complete in all respect upto the entire satisfaction of Engineer-In-Charge.

S/E of G.S.L. wire 8 SWG conforming to ISS: 280/1978/1963 with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-charge.

S/E of M.S. Stay set complete with elbow and Nuts complete in all respect made out of M.S. Rod 18mm diaand 1.8mtr. long to with stand 1000 Kg load under tension and upper and theadedupto 0.25 Mtr. Length and elbow made out of 16mm dia M.S. round shall be welded firmly on M.S. Angle of size 50 x 50 x 6mm of 180mm and (conforming o ISS 226, ISS 1732/1971) with latest amendments three of and hexagonal Nuts conforming to ISS 136/1971 with latest amendments on pole complete in all respect upto the entire satisfaction of Engineer-In-Charge. S/E of stay set 4 Nos. for 11 Mtr. Long PCC pole along with GSS wire and Disc insulator complete.

S/E of M.S. Stay set complete with elbow and Nuts complete in all respect made out of M.S. Rod 18mm dia and 1.8mtr. long to with stand 1000 Kg load under tension and upper and theaded upto 0.25 Mtr. Length and elbow made out of 16mm dia M.S. round shall be welded firmly on M.S. Angle of size 50 x 50 x 6mm of 180mm and (conforming o ISS 226, ISS 1732/1971) with latest amendments three of and hexagonal Nuts conforming to ISS 136/1971 with latest amendments on pole complete in all respect upto the entire satisfaction of Engineer-In-Charge. S/E of stay set 2 No. for 11 Mtr. Long PCC pole alongwith GSS wire and Disc insulator complete.

Supply and erection of G.O. Switches with 9 Nos. Post Insulators of Jay Shree Make Conforming to ISS:1818/1972 and ISS:2544/1963 with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge.

Supply and Erection of Three Phase 11 KV/ 0.433 KV-250 V, 200 KVA Oil immersed, naturally cooled, Aluminum Wound Outdoor type Distribution Transformers with CSP (Completely self protected) features with external microprocessor based MCCB, strictly conforming to Nigam’s technical specification No. CSC-V/R-I/DH/UH/P and D/2010-2011 read with amendment thereof and as per relevant ISS as amended from time to time and losses confirming to 4 Star rating of BEE as per Appd. make and Specification of DHBVN/ UHBVN including making of plateform and installation of transformer upto the entire satisfaction of Engineer-in-Charge. (with 6 years defect liability period, free of cost) Voltage Rated Frequency permitted at 75o C i) Maximum load losses at 50% load at 75o C = 780 watt ii) Maximum losses at 100% load at 75o C = 2300 watt iii) Warranty = 78/72 Months. The above losses are maximum allowable and these would not be any positive tolerance.

S/E and Erection of ACSR Cond. (confirming to IS 398 (PART-II)-1976 -1996,4826-1976 , IS: 1521-1972 and IS:1778-1980 with latest amendments and the erection of the same with accessories including stringing and sagging of conductor as well as jointing and binding with insulator at spots complete in all respect up to the entire satisfaction of the engineer –in - charge. ACSR Conductor 50 Sqmm

S/E of Guard made of G.S.L. Wire 8 SWG Conforming to ISS:280/1978/1963 with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge for H.T. Line.

S/E of M.S. Stay set complete with elbow and Nuts complete in all respect made out of M.S. Rod 18mm dia and 1.8mtr. long to with stand 1000 Kg load under tension and upper and theaded upto 0.25 Mtr. Length and elbow made out of 16mm dia M.S. round shall be welded firmly on M.S. Angle of size 50 x 50 x 6mm of 180mm and (conforming o ISS 226, ISS 1732/1971) with latest amendments three of and hexagonal Nuts conforming to ISS 136/1971 with latest amendments on pole complete in all respect upto the entire satisfaction of Engineer-In-Charge. S/E of stay set 1 No. for 11 Mtr. Long PCC pole (excluding cost of clamp and Nut and Bolts) alongwith GSS wire and Disc insulator complete.

Supply and Fabrication of M.S. Channel size 100x50x6mm M.S. Channel size 75x40x6mm as per relevant IS specification, painting and priming coat upto the entire satisfaction of Engineer-in-Charge.

Supply and Fabrication of M.S. Angle Iron size 50x50x6mm as per relevant IS specification alongwith painting, priming coat upto the entire satisfaction of Engineer-in-Charge.

Supply and Fabrication of M.S. Flat size 50x6mm as per relevant IS specification alongwith painting and priming coat upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of 300 Sqmm single core un-armoured power cable with aluminum conductor 650/1100 V confirming to ISS 1554(Part-I) of 1988 IS 7098/Part-I/1988 with latest amendments upto respect upto the entire satisfaction of Engineer-In-Charge. Make (Plaza/ICL/KEI/UNIVERSAL/CIRTINA).

Supply and Erection of Hot Dip Galvanized Octagonal pole made up of special sheet confirming BS-EN 10025 having single section (bolt fixing type) of minimum 3mm thickness with 86micron galvanizing including cost of nuts and bolts an all accessories as supplied by the manufacturer including cost of foundation acccessories etc. The foundation bolts as per manufacturer design should be hot dip galvanised (threaded portion). The door should be with locking arrangement,Terminal plate consisting of 2 Nos. 10A, 4 pole nutural link including connection etc. with suitable connecting arrangement for 2 Nos. MCB`s / kit kat including cost of RCC 1:1½:3 for foundation of size 0.7mx0.7mx1.8m (or as per manufacturer design) with minium 8Nos. 12mm dia longitudinal MS reinforcement rods with rings of 8mm dia not more tahn 200mmC.C. for fixing the pole with all labour and material required to complete the job in all respect upto entire satisfaction of engineer-in-charge of the work. (Makes:- Philips/Valmont/Salasar/Transrail only) (II) 8 Mtr. long octagonal pole with top dia 70mm, bottom dia 135mm, base plate of size 225*225*16mm and Foundation Bolts M20*700 `J` type (2N plus 2W)

Supply and Erection of Hot Dip Galvanized Octagonal pole made up of special sheet confirming BS-EN 10025 having single section (bolt fixing type) of minimum 3mm thickness with 86micron galvanizing including cost of nuts and bolts an all accessories as supplied by the manufacturer including cost of foundation acccessories etc. The foundation bolts as per manufacturer design should be hot dip galvanised (threaded portion). The door should be with locking arrangement,Terminal plate consisting of 2 Nos. 10A, 4 pole nutural link including connection etc. with suitable connecting arrangement for 2 Nos. MCB`s / kit kat including cost of RCC 1:1½:3 for foundation of size 0.7mx0.7mx1.8m (or as per manufacturer design) with minium 8Nos. 12mm dia longitudinal MS reinforcement rods with rings of 8mm dia not more tahn 200mmC.C. for fixing the pole with all labour and material required to complete the job in all respect upto entire satisfaction of engineer-in-charge of the work. (Makes:- Philips/Valmont/Salasar/Transrail only) (iv) 10 Mtr. long octagonal pole with top dia 70mm, bottom dia 175mm, base plate of size 275*275*16mm and Foundation Bolts M27*750 `J` type (2N plus 2W)

Supply and erection of mark double walled corrugated (DWC) HDPE pipe laid 1 Mtr. Below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-In-Charge of the work. (Make DURAGUARD/REX) (I) HDPE pipe 63/50 mm outer dia / Inner dia

Supply and Erection of Galvanized iron pipe (B-class) pole welded with MS base plate of size 15 cm x 15 cm x 3.00 mm thick, erection of the pole in ground surrounded with 15 cm dia of 1:3:6 cement concrete and a platform 10 cm thick to the size of base plate at the bottom. (III) 4.5 Meters long 65 mm dia, pole duly embedded 0.9 m below ground level.

S/E of U/G Cable loose in existing pipe or trenches complete with necessary connections :- (Make Universal/ICL / CIRTINA/KEI/Havell’s) (v) 16 sqmm. 2 core cable armoured

S/E of U/G Cable loose in existing pipe or trenches complete with necessary connections :- (Make Universal/ICL / CIRTINA/KEI/Havell’s) (xl) 16 Sqmm 4 core Cable armoured.

S/E of U/G Cable loose in existing pipe or trenches complete with necessary connections :- (Make Universal/ICL / CIRTINA/KEI/Havell’s) (xli) 25 Sqmm 4 Core Cable. (Armoured)

S/E of U/G Cable loose in existing pipe or trenches complete with necessary connections :- (Make Universal/ICL / CIRTINA/KEI/Havell’s) (xxx) 120 Sqmm 3.50 Core Cable (Unarmored.)

Supply and erection of 3 core PVC copper insulated and sheathed circular flexible wire:- (d) Size 1.50 sqmm (48/0.20mm)

Supply and erection of 3 core PVC copper insulated and sheathed circular flexible wire:- (e) Size 2.50 sqmm (80/0.20mm)

Supply and erection of aluminium lugs heavy duty including crimping etc. upto the entire satisfaction of the Engineer-in-charge of the work:- (a) 16 sqmm

Supply and erection of aluminium lugs heavy duty including crimping etc. upto the entire satisfaction of the Engineer-in-charge of the work:- (e) 25 sqmm

S/E of miniature circuit breaker / isolator 240 / 415 V in the existing distribution board including making necessary connections : - (a) Miniature Circuit Breakers of 9 K.A. breaking capacity. (ii) 6 Amp. To 32 Amp. (Single Pole)

S/E of miniature circuit breaker / isolator 240 / 415 V in the existing distribution board including making necessary connections : - (b) Isolators (ii) 63 Amp. (Triple Pole with Neutral )

Supply and erection of pipe for wiring purposes including bends inspection boxes etc. where necessary and painting as required:- vi) Galvanised iron pipe 50 mm dia on surface.

Earthling with G.I. earth pipe 4.5 Mtr. Long and 40 mm dia with masonary enclosures on the top etc. as required.

Extra for using salt and charcoal coke for pipe earth electrode as required.

Supplying and laying of 6 SWG G.I. Wire 0.5 Mtr. Below G/L as conductor earth electrode including thimble soldering etc. as required.

Supplying and laying 25mm x 6mm G.I. strip at 0.5 Meter below ground as strip earth electrode including soldering etc. as required.

S/E of moulded case circuit breaker on wall or on existing pedestal including bonding to earth and necessary connections:- (ii) 100 Amp. To 220 Amp. 415 Volt, 10 KA, 3 Phase

S/E of moulded case circuit breaker on wall or on existing pedestal including bonding to earth and necessary connections:- (iv) 300 amp to 400 V 415 V 35 KV 3 phase

Supply and Erection of Sheet steel enclosures distribution boards suitable for MCB’s etc on all/existing boards pedestal with rag bolts and necessary connection and bonding to earth:- (iv) Distribution board 4 way (Triple pole with neutral)

Supply and rection of metal clad busbar chamber made from 1.6mm thick MS sheet fixed with rag bolts on wall or on existing pedestal / angle iron frame including bonding to earth, detachable top and bottom painting and neccessary connections etc. (copper bars duly tinned). (i) 100Amp. 2 bars of 40 cm each (cross section 25mm x 3mm), chamber over all size 45cm x 20cm x 18cm.

Supply and rection of metal clad busbar chamber made from 1.6mm thick MS sheet fixed with rag bolts on wall or on existing pedestal / angle iron frame including bonding to earth, detachable top and bottom painting and neccessary connections etc. (copper bars duly tinned). (ix) 400 Amp. 4 bars of 55cm each (cross section 50mm x 5mm), chamber over all size 60cm x 55cm x 23cm.

S/E of Godrej Almirah type M.S. Pedestal made of 50x50x6mm angle iron frame with 3/-mm thick M.S. Sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars. The top covering should have downward overhang of 75mm on all sides of pedestal, having two sets of water proof ventilation holes of suitable size on the sides, at top and bottom, each set containing four Nos. holes to discharge the heat produced by the current. The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof. The Pedestal duly painted both inside and outside with two coats of approved paint and primary coat and it’s legs are embedded upto the entire depth in 1:2:4 cement concrete block, projected 75mm all around the pedestal and 200mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge. (iii) M.S. Pedestal of size 750mm wide, 900mm high and 300mm deep and bottom totally open, duly mbedded in cement concrete block of size 900mm x 450mm x 200mm above ground level duly plastered with 12MM thick 1:4 cement plaster, having a base of size 1050mm x 600mm x 250mm below ground level.

S/E of Godrej Almirah type M.S. Pedestal made of 50x50x6mm angle iron frame with 3/-mm thick M.S. Sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars. The top covering should have downward overhang of 75mm on all sides of pedestal, having two sets of water proof ventilation holes of suitable size on the sides, at top and bottom, each set containing four Nos. holes to discharge the heat produced by the current. The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof. The Pedestal duly painted both inside and outside with two coats of approved paint and primary coat and it’s legs are embedded upto the entire depth in 1:2:4 cement concrete block, projected 75mm all around the pedestal and 200mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge. (v) M.S. Pedestal of size 1200 mm wide, 1500 mm high and 450mm deep and bottom totally open, duly embedded in cement concrete block of size 1350mm x 600mm x 200mm above ground level duly plastered with 12MM thick 1:4 cement plaster, having a base of size 1500 mm x 750mm x 250mm below ground level.

Providing and Fixing hard drawn steel wire fabric 75mm x 25mm rectangular mesh with 3.25 mm dia wire fixed on steel windows of standard rolled sections with 3mm thick flat iron cover moulding of 12.5 mm width fixed with machine screw welded complete in all respect upto the entire satisfaction of Engineer-In-Charge.

Cement Concrete 1:2:4 with stone aggregate 20mm nominal size in foundation and plinth.

Supply and erection of weather proof MS box size 20cm x 30cm x 10cm of 16G and covered with MS sheet hinged cover having locking arrangement housed in 1:2:4 muff of size 40cm dia 55cm high including cost of PVC pipe of suitable size for incoming and outgoing cable, 4 copper bars of size 20mmx3mm, 125mm duly tined, insulated and supported with porcelain insulator, 2No. 16A 416V kit-kat fixed in the MS box including painting etc. complete the job in all respect upto the entire satisfaction of Engineer-incharge of work.

Supply, Installation, Testing and Commissioning of 16 Mtr. High Mast (2 section) lighting system with bottom dia 410mm, Top dia 150mm, minimum thickness of sheet 4 for bottom section, 3mm for top section and suitable to with stand the specified wind velocity 47m/sec. as per IS:875 complete with all accessories. The bottom section shall have openable slot with exterior surface door with suitable locking arrangements.The High Mast shaft shall be in two sections, hot dip galvanized and within minimum galvanizing coating thickness )75 microns . It shall also include accessories for high mast including head frame, steel wire rope 6 mm dia (7/19 construction) double drum winch, Galvanized Lantern carriage arrangement `suitable for 8 Nos.LED Flood luminaires and lightning finial. The mast shall have an integral power tool installed inside the base compartment for its operation.The high mast shall be complete with foundation bolts manufactured from special steel and hot dip galvanised along with nuts, washers, anchor plates and templates. (Makes: Philips/Bajaj/Transrail only)

Supply, Installation, Testing and Commissioning of LED street light 90watt made of pressure Die cast alumium housing with UV stabilized IP PC Lens for better light distribution and IP66 Ingress Protection having system Lumens =120LPW with inbuilt protection against short circuit, Miswiring over voltage and surge protection of 4kv plus 10Kv. The IP of LED street light shall be IP66, PF).95 and Operating Voltage between 140-270V and CRI) 70, CCT 5700K and Imapct Resistance of IK 07, service life of 50000 hrs @ L70. The specifications as mentioned above should be duly tested and mentioned in LM79 Report from Govt. approved NABL Accredited Labrotary and LM80 report of LED Chip from manufacturer required to complete the job in all respect includinh erection on existing pole for fixing including connection of the same upto the entire satisfaction of engineer-in-charge of the work. (Warranty-3 years including driver against manufacturuing defect) (Including three years Mtc/Defects Liability period free of cost) The logo of company should be on the fixture. (Makes: Bajaj/Philips/GE/LT/Panasonic)

Supply and Erection of Hot Dip Galvanized bracket 1500mm overhang (including reducer) made of 3.25mm thickness sheet 50mm dia (ID) with M.S. pipe welded to 450mm long octagonal canopy with an angle of inclination of 105° to the vertical. The top end of canopy should be closed made of M.S. sheet of 16swg, 25mm dia pipe 2mm thickness sheet should be welded diagonally at the top side of bracket and between arm and canopy. The bracket should be as per design. Single Arm Bracket (Makes:Valmont/Bajaj/Transrail)

Supply, Installation, Testing and Commissioning of LED flood light 200watt made of Die cast alumium housing, toughened glass cover with PC Lens and IP66 Ingress Protection having system Lumens )110LPW with inbuilt protection against short circuit, Miswiring over voltage and surge protection of 4kv plus 10Kv. The IP of LED street light shall be IP66, PF).95 and CRI) 70, CCT 5700K service life of 50000 hrs @ L70 with required to complete the job in all respect including erection and fixing including connection and other patty material for the same upto the entire satisfaction of engineer-in-charge of the work. (Warranty-3 years including driver against manufacturuing defect) (Including three years Mtc/Defects Liability period free of cost) The logo of company should be on the fixture. (Makes: Bajaj/Philips/GE/LT/Panasonic)

Supply, Installation, Testing and Commissioning of LED flood light 150watt made of Die cast alumium housing an toughened glass cover with PC Lens and IP66 Ingress Protection having system Lumens )110LPW with inbuilt protection against short circuit, Miswiring over voltage and surge protection of 4kv plus 10Kv. The IP of LED street light shall be IP66, PF).95 and CRI) 70, CCT 5700K service life of 50000 hrs @ L70 with required to complete the job in all respect including erection and fixing including connection and other patty material for the same upto the entire satisfaction of engineer-in-charge of the work. (Warranty-3 years including driver against manufacturuing defect) (Including three years Mtc/Defects Liability period free of cost) The logo of company should be on the fixture. (Makes: Bajaj/Philips/GE/LT/Panasonic)

Supply, Installation, Testing and Commissioning of 10watt aesthetically designed IP65 LED Bollard (H-1000mm) luminaire comprises of galvanised extruded mild steel pipe housing with opal polycarbonate diffuser and aluminum mounting base, CCT 4000K with required to complete the job in all respect including erection and fixing including connection and other patty material for the same upto the entire satisfaction of engineer-in-charge of the work. (Warranty-3 years including driver against manufacturuing defect) (Including three years Mtc/Defects Liability period free of cost) The logo of company should be on the fixture. (Makes: Bajaj/Philips/GE/LT/Panasonic)

Supply and erection of 18 Watt LED Post Top fixture Make:- of model LuxMax-PT-155 or other equivalent make and model of / GE / /Phillip’s /LT/Bajaj/Bajaj /Panasonic are made of Die cast alum. Base and spun alum. Top fitted with LED PT Module. Power LED’s are mounted directly onm inbuilt extruded Alum. Heat Slinks. A UV stabilized injection molded P.C. diffuser is provided for Glare Free Lighting with high Visual comfort complete the job in all respect including erection on existing pole for fixing including connection of the same upto the entire satisfaction of Engineer-in-Charges of the work. (Warranty- 3 Years Including Driver against any manufacturing defect Separate letter head to be given by the quoting agency). (Including Three Years Free replacement warranty and Free Mtc. at site/Defect Liability Period Free Of Cost). The logo of company should be embossed on the fixture.

Supply and erection of 20 Watt LuxMax STADIA LED Flood Light fitting Make:- TWINKLE of model LuxMax-FL-ST-20 or other equivalent make and model of / GE / /Phillip’s /LT/Bajaj made of pressure die cast alum. Body with power LED’s directly mounted on inbuilt heat sinks with anodized alum. Reflector and sealed with toughened glass complete the job in all respect including erection on existing pole for fixing including connection of the same upto the entire satisfaction of Engineer-in-Charges of the work. (Warranty- 3 Years Including Driver against any manufacturing defect Separate letter head to be given by the quoting agency). (Including Three Years Free replacement warranty and Free Mtc. at site/Defect Liability Period Free Of Cost). The logo of company should be embossed on the fixture.

Providing and Fixing of round detachable for fixing of flood light made out of 50 mm dia G.I. pipe including 2 Nos. by support of G.I. pipe 50 mm dia and pole 0.40 Mtr. long M.S. Sleeve of 100 mm dia including 50 x 6 mm Flat for fixing of gear box etc. complete in all respect up to the entire satisfaction of Engineer-In-Charge.

Supply, Erection, testing and Commissioning of 3 Phase Electronic Prod-G Meter Make Secure for street light with accessories as approved by UHBVNL including the cost of testing fee and petty material etc. required for fixing and other allied material required to complete the job in all respects. The electronic Prod-G Meter will be got installed after getting tested from UHBVNL

Construction of RCC Foundation for 16 Mtr. High Mast with installation/Erection /Testing/commissioning of High Mast complete in all respect as per the appended design including the cost of digging sand filling 6” lean concrete 1:4:8 /bricks souling, Bar blinding cement concrete (M-20) shuttering, fixing of foundation bolts, refilling, caring and erection of High mast on foundation including petty material without Foundation Nut and Bolts to complete the job in all respect up to the entire satisfaction of Engineer-in-charges of work.

S/E of Prestressed cement concrete pole as per IS: 1678/1960. (iii) 11 Mtr. Long 152mm x 203mm at top and 152mm x 360mm at bottom with working load of 360 kg. Buried 2.20 m in ground.

Supply of MS bolts of required sizes with nuts and washers complete.

Supply/Erection/Testing and Commissioning of SPECIAL PURPOSE SPEAKERS 40 W RMS of Ahuja Make Model GT-6401T/ or equivalent make and Model of SONY/Bosch complete in all respect

Supply and Erection of Speaker Wire 2.5 sqmm x 2core including connection and petty material as per site requirement complete in all respect upto the entire satisfaction of Engineer-In-Charge. Make:- Finolex//Havell’s /Polycab

Supply/Erection of DVD Player Sony make mode IBDP-S4500 or equivalent make Model of Ahuja/BOSCH complete in all respect upto the entire satisfaction of Engineer-In-Charge. • 3-D Content Playback • Wireless LAN ready • Multi Format Playability • High Definition Playback • Easy Access to Sony Entertainment Network • Optical and Coaxial Output

Supply and erection, Testing and Commissioning of Wall Mount Rack to complete the job complete in all respect upto the entire satisfaction of Engineer-In-Charge.

Supply and Erection of PVC conduit pipe ISI marked (medium) recessed in all/ceiling etc. including cost of PVC bends. Inspection box and all other material other mat required to complete the job in all respect upto the entire satisfaction of Engineer-in-charge. (b) 25 mm dia.

S/E of weather proof M.S. Box of size 20cm x 15cm x 10cm covered with 3.00mm thick M.S. Sheet hinged cover housed in 1:2:4 cement concrete muff including suitable size of PVC pipe for incoming and outgoing cables, including the cost of 1 No. 16 Amp. 415 Volts Kit Kat and 2 Nos. 63 Amp. 415 Volts neutral links, fixed o hard wood board in the M.S. box including the cost of locking arrangement, painting and necessary connections etc. (i) Muff Size 40 cm dia 50 cm High

Supply and Erection of Galvanised iron pipe (B-Class) pole welded with M.S. Base plate of Size 15cm x 15 cm x 3.00 mm thick, erection of the pole in ground surrounded with 15 cm dia of 1:3:6 cement concrete and a platform 10 cm thick to the size of base plate at the bottom (i) 2.5 Metres long 50 mm dia pole duly embedded 0.9 m below ground level

Bakelite sheet including fixing with brass screws and washers. a) 5 mm thick

Digging and Refilling of trench 30 cm below ground level for erection of pipe /cable (up to deapth of 1 Mtr..) underground cable excluding the cost of cable /pipe complete in all respect.

Supply and Erection of LED PAR with AC100V-240V 50/60 Hz. 180W Power 54 x 3W RGRW LED Units (R12 Gl4 B14 W14)` 8 DMX Channels. Strobe Eff-ect. Controls: DMX512. Master/Slave/Auto. Beanr Angle: 25o (or l5o. 45o). IP65. T`ype: SUN-6116, Moke: SUNLIT.E. complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of AC 100-240v, 50/60 Hz, 450W Power, 10R 280W Lamp, CCT 8000K, DMX512 Control, 16 DMX Channels, Pan and Tilt Movement, Color Wheel, Gobo Wheel, Effect Wheel, strobe Effect, Dimmer, IP20 complete the job in all respect upto the entire satisfaction of Engineer-in-Charge. Type SUN-2280, Make :SUNLITE

Supply and Erection of led Profile light with 1 input AC100-240V, 50~60Hz Powercon connectors, 3 DMX Channels, DMX/Strobe and delay, 50 100 190 260 360 500 beam angle available Color temperature :3200K plus 150K CRI: Ra ) average of R1~ R15 is 95 or higher TM30:Rf 92,Rg 99, 200 W COB LED, LCD Display easy for operation Ventilation Copper pipe plus silence fan, High efficiency optical system making the light brighter, NET Weight: 8.1 kg 25,000 hours of LED lifetime complete the job in all respect upto the entire satisfaction of Engineer-in-Charge. Make :SUNLITE

Supply and Erection of 1000W, 240 Volt, PAR Sealed Beam light with CRC Sheet Metal and alluminium die casting mat black color, yoke and clamp complete the job in all respect upto the entire satisfaction of Engineer-in-Charge. Type: MSSW-M64 Make :MSSW

Supply and Erection of 500 W Halogen Cyclorame Flood Light with 500W Halogen tube, Alluminium anodized reflector, 2 nos. compressible recessed single contact holders, colour frame and suitable clamp complete the job in all respect upto the entire satisfaction of Engineer-in-Charge. Type: MSSW-500C Make :MSSW

Supply and Erection of 10 Channel DMX Splitter with Two DMX input and 10 ISO outputs and 3 pin / 5 pin XLR connectors i/c connections complete as required complete the job in all respect upto the entire satisfaction of Engineer-in-Charge. Make :MSSW

Supply and Erection of 12/24 Control Panel, Type jester of Zero 88 Lighting (UK) with upto 512 control channels, 12 channels faders 2 preset master faders, fade time controls, sequence speed control, sequence master fader, grand master fader, blockout button, Flash buttons. complete the job in all respect upto the entire satisfaction of Engineer-in-Charge. Type: Jester12-24 Make :Zero 88 (UK)

Supply and Erection of Inter connecting wiring for Dimmer to Control Room with required connectors complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of Wiring 2.55 Sq. mm 3 core complete with cable tray socket and tops complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of DMX Wiring with XLR connectors 3 Pin/5 Pin complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of AHUJA PA Speaker system Model of SPX1210 complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of AHUJA Line Array Speaker Model of ALX11000 complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of AHUJA Speaker Model of SRX500 complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of Soundcraft LX7ii 32 Professional 32-Channel Mixer Console complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of Ahuja Dual Channel PA Power Amplifier DXA-1802 complete the job in all respect upto the entire satisfaction of Engineer-in-Charge. Type of Product : PA Power Amplifier Model No : DXA-1802 Weight : 26.0 Kg Power Consumption : 2700VA @ 240V / 50Hz Signal to Noise Ratio : 95dB • Dual channel direct coupled amplifier. • 1800 Watts rated output. • Rugged and reliable. Designed to work continuously under stringent operating conditions. • High fidelity sound. Ideal for high-end music programmes. Stereo/Mono 8? 370W plus 370W RMS, 4? 650W plus 650W RMS, 2? 900W plus 900W RMS Bridged Output 8? 1300W RMS, 4? 1800W RMS Single Channel Driven Output 8? 385W RMS, 4? 720W RMS, 2? 1100W RMS THD plus N 0.50% Frequency Response (-1dB) 20-20,000Hz Power Bandwidth (0.5% THD) 20-20,000Hz Channel Separation 65dB at 1kHz Damping Factor 400 : 1 (8?) Slew Rate 35V/µs Output Connectors Speakon 4-Way, Heavy Duty Screw Terminals each channel

Supply and Erection of Ahuja SA-10000 1000 Watts High Power PA Amplifier complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of Ahuja Speaker Stand STA-100 complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of Ahuja AWM-490V2 Microphone complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of Ahuja Pro plus 3400 Microphone complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of Cross-Over C1000/450 Ahuja Make complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of all other accessories like wiring, lead connector, cavint for Music System required completed in all respect.

Pdg and Fixing of Operator Room for installation Amplifiers and other accessories required complete in all respect.

Protection World