SPL REPAIR TO BLDG NO P-3/85 (08 QTRS) OF GUARDS AT RAIPUR SATWARI AND CERTAIN OTHER SANCTIONED WORKS AT MILITARY STATION JAMMU UNDER GE SATWARI

Amount

Taking down chowkats or frames with shutter (without taking off shutter from the frame) n. exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 sqm & n. exc 4 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed.

Taking down shutter exc 1.0 sqm and n. exc 2.0 sqm each and refixing after repair complete all as specified and directed.

S&F windows/ventilators made of pre-painted steel double rebate (Base steel as per IS 513 of 0.58mm thick “D” quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The quoted rate including windows should be paneled with 4 mm thick plain float glass for windows and froasted glass for ventilator and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of 04x holdfast as fasterner in each windows including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished item of work complete all as specified and directed.

S&F pressed steel frames of size 105mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including mild steel hinges, 100 mm long , medium weight (04 Nos) and 25 mm x 3 mm flat iron as in hold fast (06 Nos) , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed.

S&F pressed steel frames of size 125mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including mild steel hinges, 100 mm long , medium weight (04 Nos) and 25 mm x 3 mm flat iron as in hold fast (06 Nos) , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed.

S&F pressed steel cup board frame of size 60mmx40mm, made out of mild steel sheet 1.25mm thick with rebate 20mm wide and 12mm deep including mild steel hinges, 100 mm long,medium weight and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed.

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to distributed surface of walls complete all as specified and directed.

S&F stainless steel door using SS 304 grade steel, factory made, Box type, hollow section 0.80 mm thick, size for vertical and top rail 100mm x 35mm, size of middle rail 150mm x 35mm and bottom rail of size 200mm x 35mm single rebated comprises wire gauged skelton shutter including 150mm size stainless steel handles (2 Nos), 200mm size stainless steel tower bolts( 02 Nos) and 300mm long stainless steel sliding door bolt (01 No) complete all as specified and directed.

M&L for 35mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

S&F 35 mm thick 2nd class hard wood , glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers size of members of shutters as specified in SSR Part-I Section-8 clause 8.24 (a) fitted to chowkats complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick ( style ) consisting of frame work made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour P.V.C‘ C’ channel having a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification complete all as specified and directed.

M&L for prelaminated HDF board (exterior grade) 18/19 mm thick as in shutters /shelves , prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including 2mm thick PVC edge banding of same colour of HDF board fixed with nails/resin around the shutter complete all as specified and directed.

S&F factory made 5 mm thick PVC of density 600 Kg/CBM manufactured by an ISO 900* 2008 certified company. Plan 5 mm thick PVC sheet paneling for back side (wall side) and also manufacturer's test report and test certficate is mandatory with each and every supply of the material complete as per manufacturer specificatin and drawing complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

M&L for Framed work as in doors or gates,staging for tanks etc of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing using Fe 290 (Gde-E-165) complete. complete all as specified and directed

M&L for framed work such as grills,gratings etc with ends of bars shouldered and /or riveted or forged into spikes , framed guard bars, barred iron doors, ladders, framed balusters: walk ways , railings frame work of water tanks and similar work confirming to Fe290, Gde E-165 complete all as specified and directed

S&F stainless steel wire cloth 0.36mm normal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples/wooden beads complete all as specified and directed.

S&F 100mm long stainless steel butt hinges, fixed with screws complete all as specified and directed

S&F aluminium anodised ,fabricated type handle 125mm size complete all as spcified and directed.

S&F aluminium anodised barrel tower bolts, 200mm long of extruded section, fixed to doors with screws complete all as specified and directed.

S&F aluminum alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminum alloy and fixed complete all as specified and directed.

S&F in repair 150 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate including fixing to pressed steel frames with necessary welding work complete all as speciied and directed

S&F aluminum hanging floor door stopper ,twin rubber of size 100mm, anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour and shade with necessary screws complete all as specified and directed

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge with stainless steel brackets near to ends with stainless steel finials at both ends and necessary fittings complete all as specified and directed.

S&F in repair continuous (piano) hinges,width of flaps (when open) 30 mm, heavy duty, mild steel, bright finish or electrogalvanised sutable for 19mm thick shutter and fixed, complete all as specified and directed.

S&F hasp & staple 75 mm in length, safety type, stainless steel with stainless steel hinge pin including bolt to hinge plate fixed with screws complete all as specified and directed.

M&L for 50 mm magnetic catches with brass body and striking plate including letting in as fixed complete all as specified and directed.

S&F 100mm long stainless steel glossy finish handle, fixed with stainless steel screws complete all as specified and directed

Roughening surfaces of old concrete floor or old plastered skirting by picking, sweeping clean and washing down with water to remove dust etc and brushing surface with neat cement slurry @ 3.0 kg of cement per sq. metre complete all as specified and directed .

Dismantling floor, hearth or wall tiling/ terrazzo dado from wall surface including cement mortar bedding, (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specied and directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubing down with water etc and removing unserviceable material outside defence land complete all as specified and directed.

M&L for 8 to 9 mm thick ceramic coloured or printed, edge cut, joint free ,light shade tiles (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed .

M&L for 8 to 9 mm thick ceramic coloured or printed, edge cut, joint free ,light shade tiles (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm,in vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed ..

M&L for 7 to 8mm thick non skid coloured digital ceramic joint less tiles (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed .

M&L for glazed ceramic coloured digital tiles,300x450x7 mm thick, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

S&F machine cut kota stone slab in flooring, treads of steps, 20-25 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing cutting and mirror polishing over and including 20 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

S&F Machine cut kota stone slab in vertical surfaces such as skirting,dado,risers etc 18-20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing,cutting and mirror polishing over & including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Dismantling concrete from RCC members by chiseling , exposing the reinforcement without disturbing ,get the reinforcement free from rust by sand blasting/using rust removal chemical , providing additional reinforcement at places ( if required) duly welded with existing reinforcement , binding the concrete with 10mm gauge 50 mmx50 mm welded wire mesh & tack , securing with clips / blinding wire, welding & provision guniting pressure 2.2 to 2.5 kg /sqm with admixer 1 cement 3.5 of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control ,neccssary form work & scaffolding up to four storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick cement plaster with chicken wire mesh in cement mortar 1:4 with water proofing compound @3% by weight of cement and recron 3 S as per manufacturer instructions, cleaning & removing of waste meterial etc as appply two coats of Dr fixit /pidilite/sika/Fosroc new coat ezee at interval of 8 hours cure for the surfaces complete all as specified and driected.

Demolition of reinforced cement concrete of any description & in any position not otherwise described for and removing the rubbish from the work site to outside defence premises complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 (nominal mix) type B1 (using 20 mm graded crushed stone aggregates) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed .

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed .

M&L for use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for fair finished surfaces of concrete, complete all as specified and directed.

M&L for use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n.exc. 20cm wide for fair finished surfaces of concrete, complete all as specified & directed

M&L for 16-18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite & moulding the edges,making hole for gas pipe over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Complete removal of existing water proofing treatment of any description including under layer, taking down cement plaster any thickness,PCC tiles,mud phuska etc and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust and removal of debris off the premises including grubbing up of trees complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in padding over roof, finished & laid to required slope complete all as specified and directed .

M&L for cleaning of the exposed concrete slab & like and repairing the surface irregularities like cracks, potholes with HS Latex Plus(or equivalent) & cement in mixing ratio of 1:4 as per manufacturers method statement by Berger HS Rapairo (or equivalent) including 15mm thick rendering in cement mortar 1:3 complete all as specified and directed .

M&L for HomeSheild PU Roofkoat(or equivalent) is a one component liquid ,solvent free , cold applied , water-proofing membrane that is highly elastic and UV resistant with 10 years warranty .ASTM D 6083-97 a Waterproofing and heat reflecting system having following key performance properties:- a) UV resistant ,prevent yellowing and weathering b) Highly elastic upto 350% and crack bridging c) Excellent adhesion on porous and non-porous substrates d) Tensile Strength >10 N/mm2 with GeoTextile fleece e) Soler Reflective Index (SRI) more then 109-111 ASTM E1980-11 System: First coat:Providing and applying primer over the prepared surface with HS PU roofkoat Primer(or equivalent) Coverage: 0.2kg/sqm(with 50% dilution of water) Reinforcement: Geotextile 40 gsm Second coat:Home sheildroofkoat(or equivalent) Consumption: 0.5 kg/sqm. Third coat: HS PU roofkoat(or equivalent) Consumption : 0.8 kg/sqm. System buildup-1.5kg/sqm with geotextile of 40gsm

Demolition of cement concrete (un-reinforced) in ground floor and pavings exc 15 cm thickness (below or above ground level) and removing the rubbish from the work site to out side defence premises complete all as specified and directed

M&L for glass fibre reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent). Base coat: Berger HS Latex plus (or equivalent) both on wall (upto 1 mtr min height) and floor. Consumption base coat: 0.3 kg/sqm Reinforcement: Glass fiber Second and Third coat: Latex sheild 2K (or equivalent) both on wall (upto 1 mtr min height) and floor. Consumption top coat: 3 kg/sqm System requirements: density: 2.00 kg/ltr compressive strength: 0.5 N/mm². • Wall penetration through the RCC slab must be sealed using Berger HS RepirO(or equivalent). • Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus(or equivalent) modified mortar with a bonding coat of Berger HS Latexplus(or equivalent) modified cement slurry upto 5ft. • All depressions, unevenness, surface honeycombing shall be repaired using Berger HS Latex plus (or equivalent) modified polymer mortar with a bonding coat of Berger HS latex plus(or equivalent)modified cement slurry including cleaning of RCC surface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges, etc

M&L for 10mm thick rendering in cement mortar 1:4 on concrete surfaces as in roof, finished even & fair and including mixing of water proofing compound complete all as specified and directed . Note:-WPC shall be measured and paid separately

M&L for steel water tubing of 40 mm bore,medium grade,galvanised, laid in sunken floors as spout complete all as specified and directed.

Demolition of plain cement concrete of any description & in any position not otherwise described for and removing the rubbish from the work site to outside defence premises complete all as specified and directed.

Supply only liquid water proofing compound.

M&L for dismantling of water tank of capacity exc 250 ltrs but n. exc 500 ltrs and removing complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks of 500 litres capacity (cylindrical vertical with closed top) with plastic lid cover, hoisted and fixed in position including PTMT Ball valves high pressure with epoxy coated aluminum rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe including making connections complete all as specified and directed.

S&F in repair Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:2:4, type B2 (using 40 mm graded crushed stone aggregates) as in sub base and surface finished even and fair complete all as specified and directed

M&L for 75 mm plain cement concrete 1:4:8, type D2 (using 40mm graded crushed stone aggregates) as in sub base floor/pavings and surface finished even and fair complete all as specified and directed

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete as directed, edge joint filling with cement mortar 1:4 complete including necessary excavation complete all as specified and directed

M&L for 25 mm thick plain cement concrete 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregates) as in sub base/ levelling course of floors, finished even and fair complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 , type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection, laid in slope in 1:20 in alternative bays not exceeding 3 mtr in length. surfaces finished even and fair including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:2 complete all as specified and directed .

Demolition of cement concrete (un-reinforced) in ground floor and pavings n.exc 15 cm thickness (below or above ground level) and removing the rubbish from the work site to out side defence premises complete all as specified and directed

Taking up or down 15mm dia GI tubing and conncetions including cleaning for refixing or removal to store complete all as specified and directed

Taking up or down 20 mm dia GI tubing and conncetions including cleaning for refixing or removal to store complete all as specified and directed

S&F Galvanised steel tubing, 15mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed

S&F Galvanised steel tubing, 20mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed

M&L for cutting (in brick walls) chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sun shades, shelves, Iintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting n.exc 10cm grith complete all as specified and driected.

S&F in repair angle valve with flange,cast copper alloy , fancy type, chromium plated, screwed down for high pressure , screwed both ends for iron pipe of 15mm bore complete all as specified and dircted.

S&F in repair bib taps, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle , screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair brass chromimium plated sink mixer swan neck with swinging spout (wall mounted model) with connecting Legs & wall flanges complete all as specified and directed. .

S&F in repair pillar tap, chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe of 15mm bore complete all as specified and directed.

S&F in repair wall mixer 3-in-1 system with provision of overhead & hand shower complete with 115mm long bend pipe, connecting legs & wall flange fancy type complete all as specified and directed.

S&F in repair fancy type 125mm square size brass chromium plated shower rose with 195mm long shower arms with bend 45 degree with brass flange complete all as specified and directed .

S&F in repair sinks with drainage board, made of 1.0mm thick stainless steel,overall size of sink 915mm x 460mm with bowl size 410mm x 330mm x 160mm, plugs, washers, waste pipe , union, CP waste coupling and cantilever brackets embedded in cement and sand mortar in wall complete all as specified and directed

S&F in repair plate rack made of 1.00mm thick stainless steel of size 30"x36"x10" fixed with steel fastners or steel screws complete all as specified and directed

S&F in repair vitreous china wash hand basin with pedestal, white, flat back of size 580x450x820mm including cutting for and pinning in ends of brackets or erecting stand including cast iron brackets, brass chromium plated waste coupling 32mm bore, waste pipe PVC 32mm bore complete all as specified and directed

S&F in repair vitreous china wash down water closet pan (pedestal pattern) of size 520x360x390mm white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes, connecting only to flushing cistern, anti-syphonage pipe with PVC flush pipe of 32mm dia including plastic seat with cover, white in colour with mild steel chromium plated hinging and 'P' or 'S' trap device complete all as specified and directed

S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed.

S&F in repair 10 litres PVC, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float 32mm PVC 'L' bend and handle including brackets complete all as specified and directed

S&F in repair towel rail 600mm long of PTMT fixed with and including CP brass screws including wooden/plastic cleats (Min weight 190 gms) complete all as specified and directed.

S&F in repair Stainless Steel soap dish of size 160x160x90mm, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisiting of 5.5 mm thick sheet glass, shelf 12 cm wide with chromium plated bracket guard and railing 45 cm long complete all as specified and directed.

Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings and removing from site complete all as specified and directed

S&F PVC (SWR) type B pipes, 110 mm bore, single socketed, in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed..

S&F PVC (SWR) type B pipes, 110 mm bore, single socketed, in any length with rubber ring joints, fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed..

S&F PVC (SWR) type B pipes, 75 mm bore, single socketed, in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed..

S&F PVC (SWR) bends with access door any radius, 75 mm bore complete all as specified and directed

S&F PVC (SWR) bends with access door any radius, 110 mm bore complete all as specified and directed

S&F PVC (SWR),branch piece, (single 'Y') equal or unequal for 110 mm bore complete all as specified and directed

S&F PVC (SWR), junction single, (single 'T') equal or unequal for 75 mm bore complete all as specified and directed

S&F PVC (SWR), junction single, (single reducer 'T') equal or unequal for 110mmx75 mm bore complete all as specified and directed

S&F PVC (SWR), junction single, (single 'T') with access door equal or unequal for 75 mm bore complete all as specified and directed

S&F PVC (SWR), junction single, (single 'T') with access door equal or unequal for 110 mm bore complete all as specified and directed

S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed

S&F PVC (SWR) floor trap plain with stainless steel grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F PVC (SWR) type-B multi floor trap plain with stainless steel grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F PVC (SWR) vent cowl 75 mm dia complete all as specified

S&F PVC (SWR) vent cowl 110 mm dia complete all as specified

Demolition of brick work or stone/boulder masonry , built in cement mortar or cement lime mortar including all quoins, arches & pillars etc of any description and in any position and removing unserviceable material from work site to outside defence premises complete all as specified and directed

M&L for brick work with sub class 'B' bricks, using old size bricks, straight or curved on plan exceeding 6m mean radius,built in cement mortar 1:6 complete all as specified and directed

All as per Ser item No 104 here-in-before but except bricks complete all as specified and directed.

M&L for brick work with old size sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed .

M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surface,surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on brick work or concrete surfaces, surface finished even and smooth without using extra cement complete all s specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L for preparation of new or previously untreated wood or wooden based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described by rubbing with sand paper or grinding by hand grinder to make surface even and smooth & apply primer where required and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted wood and wood based surfaces of any description over 10cm width or girth not otherwise described by grinding the uneven surfaces and necessary filling of putty (as and where required) to make surface even and smooth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for complete removal of existing treatment on wall/Ceilling,roof projectios,Including facia,cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. by skilled labour (up to 4th storey with necessary scaffolding) complete all as specified and directed.

M&L for water proof cement based putty @ 1kg (undiluted) per sqm of average thickness 1 mm over the plastered painted exterior wall surfaces of walls (upto 4th storey with necessary scaffolding ) including prepartion of surfaces by scarpping to prepare the surface and sanding of the putty surfaces with mechanical wall sander (having mechanical vaccum mechanism ) having RPM not less than 1500 ,sanding pads of 240 Grit or above to make the surface free from dust etc by skilled llabour as per following steps:- Steps 1:- Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of minimum 2.5 kg putty per minute. Step 2:- Apply the first coat of prepared mixer with the manually required help of fully automatic airless spary machine of putty application, finishing the surface even and smooth in level without any undulation. Step 3:- Allow 6 to 8 hour time to dry the putty surface, Apply the further more coat of preparaed mixer with the help of fully automatic airless spary machine of putty application, finishing the surface even and smooth in level without any undulation.

M&L for one coat of acrylic waterbased interior/exterior (wall/ceilling up to 4th storey with necessary scaffolding) grade primer @ 0.8 ltr(undiluted)/10 sq mtrs diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface for painting of subbsequent coats complete all as specified and directed .

M&L for preparing the putty surface by sanding paper and applying two coats of oil bound distemper on wall/ceilling (up to 4th storey with necessary scaffolding) using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed.

M&L for water based premium acrylic smooth exterior emulsion for approved colour (up to 4th storey with necessary scaffolding) with silicon additive excellent dirt pickup resistance with low VOC less than 50 AntifugalAnti Algai properties in two coat @1.79 litre (unndiluted) /10 sq mtrs diluted with water as per manufacturer instructions applied over priming surface with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in between subsequent coats of paint complete all as specified and directed. Notes for Srl item No 114 to 118 of BOQ :- (a) The work for periodical services shall include the under mentioned aspects and the rates quoted by the bidder shall includes and the same & nothing extra shall be payable. (i) Work shall be carried out by the authorised applicator of manufacturer of water based premium acrylic smooth exterior emulsion, contractor shall submit a triparty agreement MoU (between contractor ,said manufacturer and their authorities appicator ) on Non judicial stamp paper to GE and shall be approved by the GE before commecement of work at site. (ii) Work shall be carried out up to 4th storey height buildings and the necessary scaffolding , trestles , ladders ,cradles & safety measures shall be arraged by the contractor for labour and their own . (iii) Removing of nails & making good holes, cracks etc. (iv) Work in patches and in narrow /widths ,bands ,cornises ,plasters etc shall also be carried out and cutting in edge of line where ncessary. (v) Spreading and removing covering to doors ,windows ,floor ,fittings etc to protect them from splashes. (vi) Washing floors , cleaning glass ,joinery, fittings, wiring etc from drops and splashes of paint to be cleaned to the statisfaction of Engineer-in-charge. (vii) Sample patch of 10 sqm be prepared considering all the items of periodical and shall be got approved from GE prior to carrying out further work.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over two coats of wall care putty 1 mm thick each and one coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of weather proof acrylic emulsion paint over one coat of wall care putty 1 mm thick and one coat of primer complete all as specified and directed.

M&L for complete removal of existing treatement on wall surfaces including washing and rubbing down , preparation of surfaces and applying two coats of weather proof acrylic emulsion paint over one coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specified and directed.

M&L for complete removal of existing treatement on wall surfaces mechanically including washing and rubbing down , preparation of surfaces and applying two coats of oil bound distemper over two coats of wall care putty of 1 to 2 mm thick each and one coat of primer complete all as specified and directed.

M&L for 8 to 9 mm thick vitrified ceramic double charged, joint free, coloured or printed any shade tiles (square/ rectangular) polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for 8 to 9 mm thick vitrified ceramic double charged, joint free, coloured or printed any shade tiles (square/ rectangular) polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , as in vertical surfaces such as skirting / dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

S&F 35 mm thick HDF door shutter (double/single leaf) both side laminated and surrounding to be covered with minimum 2 mm thick edge bond tape of same colour complete all as specified and directed.

Taking down old/unserviceable kitchen cabinet/cupboard including all fixtures and fittings complete all as specified and directed. Note : For measurement superficial area in elevation shall be measured.

S&F 16 mm thick plywood, BWP as in frame work of the cabinet doors including drawer fascia/sides/bottom/top shelves etc. All exposed surfaces of internal and external surfaces of the units shall have machine pressed HD gloss finish lamination having thickness 1 mm of approved shade and make and pasted with synthetic resin based adhesive etc. The thickness of four edge PVC lipping for shutters and drawer fascia shall be 32mm thick. The lippings/banding shall match with the external laminate shade complete all as specified and directed.

S&F 16 mm thick plywood , (BWP as in frame work of the cabinet doors including drawer fascia/sides/bottom/top shelves etc. All exposed surfaces of internal surfaces and un exposed surfaces of the units shall have machine pressed HD matt finish lamination having thickness of 0.8mm of approved shade and make and pasted with synthetic resin based adhesive etc. The thickness of four edge PVC lipping of carcass/plywood partition should be 0.8mm and thickness of four edge lipping around the rebate of glass shutter shall be 0.6mm. The lippings/banding shall match with the external laminate shade. All shelves shall be supported on approved quality stainless steel pins and shall be adjustable for various height requirement . The cabinet shall be firmly fixed to the walls/slabs/floor using non-corrosive metal screws/fastener of appropriate size and rawl plugs complete all as specified and directed.

S&F EURO type slip/Auto Hinges of best quality in shutter complete all as specifeid and directed.

S&F profile brush finished 150 mm long stainless steel handle of grade 304 complete all as specified and directed.

S&F high precision soft close telescopic channels/sides to be designed as per drawer size and to meet the weight requirement with minimum length of 500 mm to ensure smooth movements of drawer and load capacity of channel is minimum 45 Kgs complete all as specified and directed.

S&F stainless steel (SS 304 grade) perforated cutlery basket of size not less than 500mmx525mmx100mm complete all as specified and directed.

S&F stainless steel (SS 304 grade) cup & soaucer basket of size 460mmx510mmx150mm complete all as specified and directed.

S&F stainless steel (SS 304 grade) Thali basket of size 500mm x500mmx200mm complete all as specified and directed..

S&F stainless steel (SS 304 grade) plain multipurpose baskets of size 500mmx525mmx 200mm complete all as specified and directed..

S&F stainless steel (SS 304 grade) three tier oil/masala pull out of size 200mmx500mmx 590mm complete all as specified and directed.

S&F stainless steel (SS 304 grade) 2 tier detergent pull out of size 110mmx505mmx 430mm complete all as specified and directed.

S&F stainless steel (SS 304 grade) sink with bin holder (Dia 250mm, height 450mm) complete all as specified and directed.

S&F 5 mm thick float glass fixed with plywood including necessary cutting of grooves in plywood including stainless steel cleats and clips complete all as specified and directed.

S&F 10 mm thick float glass as in glass shelf, fixed with plywood including necessary cutting of goorves in ply wood including cleats and clips complete all as specified and directed. Note for item No 132 to 137:- The stainless steel rods provided in the baskets shall be of combination of 5.5mm dia and 2.8mm dia rods.

M&L for factory made box type steel windows, double shutter,outer frame made out ERW TUBE 'P section (60x35x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) openable shutters side hung including pintle hinges with two nos MS tower bolts 150mm size on each shutter, steel handle and stopper of 'Z' section as specified complete with sash bars dovetailed or welded ready for glass fixing and wire gauzed fixing with suitable fittings/opening for cooler/AC where required .Steel windows will be double shutter (external glazed and internal wire gauzed) complete all as specified in Drg No CEPZ/C-TD/27/13 of sheet No 1/4 to 4/4 complete all as specified and directed. Note: - The quoted rate shall be deemed to include :- (i) Provn of one coat of coal tar on the ends of steel frame in contact with brick/conc surface (ii) 04 Nos MS steel lugs of MS flat 20 x 5mm & 20 cm long over all welded to frames (iii) PCC block for embedding lugs. .(iv) Provn of 10 mm square bar as guard bar, spacing 100 mm c/c all as per drg and including 4 mm thick flat iron for fixing of guard bars all around .

S&F in repair aluminum powder coated (coating not less than 50 micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, necessary glazing and locking arrangements, anodised aluminium fittings with provision of space for exhaust fan (if required) including finishing disturbed surfaces even and smooth in cement mortar 1:3 and applying two coats of oil bound distemper over two coats of wall care putty 1 to 2 mm thick each complete all as specified and directed.

M&L for aluminum powder coated (coating not less than 50 micron), sliding window, three track with stainless steel mosquito proofing with window style of section 44.4mmx44.5mmx 2.0mm thick and frame of section 101.60 x 44.45 mmx 1.20mm thickness including 4.0 mm thick coloured/tinted/frosted glass panes & stainless steel wire mesh of aperature 0.63mm and all necessary fittings and fixtures complete all as specified and directed.

S&F aluminium anodised barrel tower bolts, 150mm long of extruded section, fixed to doors with screws complete all as specified and directed.

S&F aluminium anodised ,fabricated type handle 100mm size complete all as spcified and directed.

S&F in repair brass chromimium plated sink cock with swinging spout (wall mounted model) with wall flanges complete all as specified and directed.

S&F in repair sinks , made of 1.0mm thick stainless steel,overall size of sink 610mm x 460mm with bowl size 560mm x 410mm x 200mm, plugs, washers, waste pipe, union, chromium plated waste coupling and cantilever brackets embedded in cement and sand mortar in wall complete all as specified and directed

S&F in repair stainless steel lock grating plain/hole size 100 mm dia including embeding in tiles with white cement complete all as specified and directed.

Taking up or down 25 mm dia GI tubing and conncetions including cleaning for refixing or removal to store complete all as specified and directed

S&F Galvanised steel tubing, 25mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed

S&F PVC (SWR) type B pipes, 75 mm bore, single socketed, in any length with rubber ring joints fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed..

S&F GI snap grid frame work (Grid size 605mm x 605mm) for false ceiling consisting of main runner 'T' of size 24mm x 32mm and 0.3mm thick , Secondary runner 'T' of size 24mmx25mm and 0.3mm thick,GI angle 24mmx24mm and 0.4mm thick,Bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm / Sqm ,ceiling grid system duly suspended by 4mm dia GI wire hanging from existing purlins /roof slab with butterfly clips including Gypsum ceiling tiles of size 595 x 595 x 9 mm laminated with 0.07 mm thick polyvinyl film on the face side and 10 micron metalized polyester film on the back side fixed on GI snap grid complete all as specified and directed ..

Surface dressing n.exc. 15 cm deep and getting out in any type of soil complete all as specified and directed.

Excavation in trenches in any type of soil, not exceeding 1.5m deep and 1.5m wide for foundation etc or manholes, piers , shafts etc not exceeding 10 Sqm on plan & not exceeding 1.5m in depth and getting out complete all as specified and directed.

Returning , filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed

Removing excavated material to a distance n. exc 50m & depositing whrere directed at a level n exc 1.5 m above the starting point complete all as specified and directed.

M&L for plain cement concrete 1:4:8, type D2 (using 40mm graded crushed stone aggregates) as in foundation, filling & mass concrete complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4, Type B-1 (using 20 mm graded crushed stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed .

M&L for reinforced cement concrete 1:2:4, Type B-1 (using 20 mm graded crushed stone aggregates) as in column,pillars, piers and struts complete all as specified and directed.

M&L for use and waste of form work to sides of concrete foundations, footings, bases of columns , raft and raft beams, sides and softfits (if any) of foundation and plinth beams and similar work, vertical or batter for rough finished surfaces of concrete complete all as specified and directed.

M&L for use and waste of formwork to sides of pillars, posts, struts, piers, columns, and stanchions etc for fair finished surfaces of concrete complete all as specified and directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for sand filling under floor including spreading, levelling, watering and well ramming in layers n exc. 25 cm thick complete all as specified and directed .

S&F Vitreous china half stall Urinal of size 375x390x590mm, white including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, flush pipe, grating and union for discharge pipe and Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for hard core of gauge not exceeding 63mm using broken stone or boulders, deposited, spread and leveled in layers not exc 15cm thick, watered and rolled/rammed to a true surfaces complete all as specified and directed .

M&L for plain cement concrete 1:2:4 ,type B1(using 20mm graded crushed stone aggregates) as in lintels upto 1.5m clear span, window or door cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings,side posts of precast jallies etc. including slightly rounded or chamfered angles including necessary formwork complete all as specified and directed.

S&F UPVC (SWR) bends any radius, 100 mm bore complete all as specified and directed

S&F vitreous china squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rest, cast iron 'P' or 'S' trap of size 100mm, including provision of plain cement concrete bedding and connection to trap and to flushing pipe, anti syphonage pipe etc and making good the floors complete all a specified and directed

M&L for reinforced concrete pipes class NP-2 laid and jointed complete with collar of size 150mm (internal dia) all as specified and directed.

S&F vitreous china table top wash basin, size 600x480x150mm, rectangular shape , white, to be fixed on counter/ RCC slab including chromium plated waste coupling, 32mm waste pipe complete all as specified & directed

S&F tall body single lever basin mixer suitable for table top wash hand basin, without popup waste with 450mm long braided hose, fancy type complete all as specified and directed.

S&F brass chromium plated tubular towel rail 20mm dia, D type , 600 mm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed.

S&F sheet glass shelf assembly consisiting of 5.5 mm thick sheet glass, shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F corner glass shelf 5.5mm thick of size 30cm with Chromium plated bracket guard and railing fixed with and including screws and wooden/plastic cleats complete all as specified and directed .

S&F health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern) of size 520x360x390mm white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes, connecting only to flushing cistern, anti-syphonage pipe with PVC flush pipe of 32mm dia including plastic seat with cover, white in colour with mild steel chromium plated hinging and 'P' or 'S' trap device complete all as specified and directed

S&F 10 litres PVC, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float 32mm PVC 'L' bend and handle including brackets complete all as specified and directed

S&F bib taps, with wall flange chromium plated, fancy type, cast copper alloy with crutch or butterfly handle , screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F angle valve with flange,cast copper alloy , fancy type, chromium plated, screwed down for high pressure , screwed both ends for iron pipe of 15mm bore complete all as specified and dircted.

S&F PVC connection 15 mm x 600 mm including brass check nut at both ends complete all as specified and direced.

S&F Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on concrete surfaces of roof finished even and fair including mixing of water proofing compound as per manufacturer's instructions complete all as specified and directed. Note : Water proofing compound shall be measured and paid separately as supply only.

M&L for water proofing treatment in the following sequences:- (a) Applying 1st course of bituminous primer confirming to IS-3384 @ 0.4 Kg/sqm .Cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely. (b) Applying 2nd coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (c) Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.6 Kg/sqm with 160 Grams/sqm non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat complete all as specified and as directed (d) Complete treatment to be carried out by authorised applicator of waterproofing manufacturer.

M&L for applying two coats of aluminum paint over the APP membrane complete all as specified and directed.

Taking down carefully existing aluminium/copper point wiring for light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells etc & making good the disturbed surfaces of walls/ceiling, matching the colour with existing surface complete all as specified and directed. Note : Rate for making good shall be deemed to be included in above item rate.

Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLSH with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed medium grade conduit of suitable size with all accessories such as bend, reducers, MS hooks including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc including continuous earth wire of size 1.5 Sqmm PVC FRLSH stranded copper conductor unsheathed, insulated, stranded connected to common earth point dolly for one light point/fan point/call bell point, 230 volts controlled by one switch complete all as specified and directed . Note:- Proper colour coding is to be followed as per IS specifications.

All as per srl item No 188 above but One 3 pin socket outlet 6 amp independent complete all as specifieds and directed

All as per srl item No 188 above but One 3 pin socket outlet 6 amp same board complete all as specifieds and directed

All as per srl item No 188 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

S&F modular type switch, one way 6 Amps , 1 module complete all as specifieds and directed .

S&F modular type switch, one way, 16 Amps, 1 module complete all as specifieds and directed .

S&F modular type socket 3 pin, 6 Amps, 2 module complete all as specifieds and directed

S&F modular type socket 3 pin, 6 A/16 Amps, 2 module complete all as specifieds and directed .

S&F modular bell push with indicator polycarbonate materials 6 Amp 240 volts 1 module complete all as specifieds and directed.

S&F bell ding dong AC 230 volts single phase complete all as specified and directed.

S&F modular type fan regulator, step down 120 Watt, 2 module complete all as specifieds and directed.

S&F lamp holder,PVC /Polycarbonate type with back plate for batten fittings complete all as specifieds and directed . .

S&F ceiling rose, surface backelite, two/ three terminal, 240 volts complete all as specifieds and directed .

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt, 220 V, AC ,decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specifieds and directed .

S&F LED light fitting 1 x 20Watt, 220V, Integrated batten type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose with all fixing arrengenment complete all as specified and directed.

S&F MCB SPN,40-63 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specifieds and directed .

S&F MCB Single pole, 6 to 32 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specifieds and directed .

S&F Sheet metal enclosure for DBs,SPN, double door,IP-54 protected, 415 Volts,8 ways with 200 amps rated copper bus bar complete all as specified and directed

S&F Submain wiring with two runs of single core PVC FRLSH unsheathed, insulated, copper cable of 4 Sqmm size, multi stranded, 1100 volts grade with PVC insulated,unsheathed FRLSH copper wire 4 Sqmm for continous earth wire drawn into and including concealed PVC conduit of suitable size complete all as specified and directed . Note :- Two runs of 4 Sqmm copper cable and one run of 4 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length)

M&L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1, precast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh ,15mm dia light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specifieds and directed ..

S&F LED light fitting 1 x 18Watt, 220V, Integrated batten type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose with all fixing arrengenment complete all as specified and directed.

S&F exhaust fan, steel body, AC single phase. 230 V of size 300 mm sweep with, blades and frame and louvers, hanging on wall with 4 Nos steel fasterners 10mm dia & 100mm long including wall hole and making good the disturbed surfaces as per existing complete all as specified & directed

S&F Sheet metal enclosure for DBs,SPN, double door,IP-54 protected, 415 Volts,4 ways with 200 amps rated copper bus bar complete all as specified and directed

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 4.0 Sqmm 2 core nominal cross section in service connections complete all as specified and directed.

THAKUR BUILDERS AND CO (BID ID -3448510)

M/s KULDEEP KUMAR CONTRACTOR (BID ID -3448755)

AKSHAY CONSTRUCTION COMPANY (BID ID -3453221)

M/S Shesh Paul Gupta (BID ID -3448701)