GE/S(U)-07/2021-22 SPECIAL REPAIR TO CONTROL ROOM GUARD POST AND EXISTING ENTRANCE GATE AT THE ENTRANCE TO AVIATION BASE BIKRAM PARK REPAIR TO EXISTING SECURITY FENCE AROUND THE HELIPAD AREA PROVN OF GALVALUME ROOF SHEET FALSE CEILING AND OTHER ALLIE

Amount

Dismantling plain or corrugated steel sheeting, any gauge thickness, including Nainital or similar pattern roof covering complete all as specified and directed.

Dismantling framed work timber scantlings 40 Sqcm and over in section, in any position complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified and directed.

Demolition cement concrete in ground floors and paving (unreinforced) not exceeding 15 cm thickness (below or above ground floor) complete all as specified and directed.

Demolition of reinforced cement concrete of any description or any position not otherwise specially provided for complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish of the premises complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pilars etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Rolled Mild steel as in main and cross beam, hip and jack rafters, purlins where connected to common rafter and running rails fixed for angle cleat etc. as per requirement of gde Fe-410W (Gde E-250 quality) complete all as specified and directed by Engr-in-Charge.

Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick crimpted/tapard at the external end slop of any colour having tansile strength 550 Mpa as in roof covering fixed with self tapping screws and caps etc complete all as specified and directed.

Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick in ridges, hips, valley gutters at the external end slop of any colour having tansile strength 550 Mpa as in roof (ridges) covering fixed with self tapping screws and caps etc. complete all as specified and directed.

Mild steel screw bolt (machine made) 11 to 15 mm dia with hexagonal or square heads at one end and screw the other, or screwed both end to be fitted with washers and one hexagonal or squre nut exceeding 10 cm and not exceeding 15 cm long complete all as specified and directed.

75 mm thick plain cement concrete, type C-2, (1:3:6) (using 40 mm graded aggregate) as in plinth protection complete all as specified and directed.

Brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard /dense soil complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation & not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

Returning, filling including spreading leveling watering and well ramming in layers not exceeding 25 cm in any type of soil complete all as specified and directed.

Removing excavated material (soils) exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs etc. complete all as specified and directed by Engr-in-Charge.

Providing Reinforced Cement Concrete design mix M-25 (using 20 mm graded aggregate) as in foundation including rafts, footings, foundation beams, plinth beams, bases of columns etc. complete all as specified and directed.

Providing Reinforced Cement Concrete design mix M-25 (using 20 mm graded aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed.

Providing Reinforced Cement Concrete design mix M-25 (using 20 mm graded aggregate) as in beams, cantilever, lintels over 1.5 m complete all as specified and directed.

Use and waste form work to sides of concrete foundation footings base of coloumns sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished flat surface of concrete complete all as specified and directed.

Use and waste formwork to sides of columns, pillars, posts, struts, piers and stanchions, rectangular or square for rough finished flat surfaces of concrete complete all as specified and directed.

Form work to flat sides and soffits of or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splays between floors and beams complete all as specified and directed.

TMT bars 10 mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per ser item No 27 above but 5 mm dia and over including 10 mm dia in stirrups, spaces and binders etc. complete all as specified and directed.

15 mm thick rendering on fair faces of brick/ concrete or stone surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete with water proofing compound complete all as specified and directed.

15 mm thick rendering in CM 1: 4 on fair faces of brick work or concrete surfaces for backing coat for tiles complete all as specified and directed.

20 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

75 mm thick cement concrete (1:4:8) type D-2 as sub base to floor complete all as specified and directed.

25 mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in floor and finished even and fair complete all as specified and directed.

20 mm thick granite (of any type) machine cut as in dado etc laid over cement backing coat and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grainding and polishing complete all as specified and directed by Engr-in-Charge.

Dura stone tiles of size 305 mm x 305 mm x 10 mm thick as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the surface of tiles complete all as specified and directed. Note :Shade/colour as approved by GE.

Wall cladding colour designer tiles of size 300 mm x 600 mm x 7 mm thick (shade as approved by GE) set and jointed in neat cement slurry and laid over screed bed/ backing layer of 10 mm thick in cement mortar and pointed in white/coloured cement to match the colour of tiles as on vertical surfaces such as dado/skirtings complete all as specified and directed.

Framed work such as grill, gratings, etc with ends of bars shouldered and/or riveted or forged in to spikes, framed guard bars, barred iron doors ladders framed balusters and similar work for portion framed and hung as gates including pintle hinges steps hand made sliding bolts etc. including ornamental and intricate design confirming to Fe 290 Gde E-165 as in repair complete all as specified and directed.

Applying two coats of cement based paint over a coat of chalk whiting including preparation of new plastered surfaces complete all as specified and directed.

Applying one coat birla wall care putty on old plastered on wall surfaces including preparation of surface by brooming down or steel wire brushing, scrapping down vegetation growth, efflorscent salts and trading with oil greasy spot complete all as specified and directed with complete removing.

Two coats of distemper oil emulsion over a coat of primer including preparation of old plstered surfaces of walls complete all as specified and directed.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide chrome primer complete all as specified and directed.

Stainless steel pipes as in framing for fixing of railing including fixing of 10 mm thick toughened glass on frame as per site requirement confirming to Gde 304 complete all as specified and directed by Engr-in-Charge. Note : Toughened glass will be measured and paid separatly.

Brass CP powder coated 300 mm height and 100 mm wide words (English Alphabets) fixed on walls with adhesive or necessary arrangements, word will be as per users requirements and complete all as specified and directed by Engr-in-Charge.

4 mm thick AC board (designer ceiling) of size 600 mm x 600 mm panel confirming to IS 14862 type B category three including GI frame work with size of grid 605 mm x 605 mm for seanless ceiling comprises of GI perimeter including all accessories complete all as specified and directed. Make : Everest.

Powder coated anodised aluminium frames for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified and directed.

Powder coated aluminium anodised door shutter shutters, side hung type without sash bar, aluminium section weighing 0.55 kg/m including necessary jointing cleat glazing clips, rubber packing, anodised aluminium snap beading screws etc. complete all as specified and directed. (Thickness or powder coating not less than 50 micron)

Aluminium body heavy duty double action floor spring suitable for glass shutter at both side rotable complete all as specified and directed. Make : OMEGA/HARDWIN

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling old serviceable/unserviceable barbed wire including removing of unserviceable barbed wire from site and serviceable materials kept in safe custody for re-use complete all as specified and directed.

Excavation in post holes (or similar holes) each not exceeding 0.5 cum, getting out in soft and loose soil, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm watering and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and directed.

Dismantling post or struts (wood, steel or RCC) any section, including taking out embeded portion and making good disturbed ground. Post emdeded in concrete, brick work, masonry etc. complete all as specified and directed.

Dismantling expended metal, any thicness or mesh, fixed with steel or wood fillets if any or welded to steel frame, weight not exceeding 4 kg per sqm complete all as specified and directed.

PCC (1:2:4) type B-2 (using 40 mm graded stone aggregate) foundation fillings and mass concrete complete all as specified and directed.

Welded steel wire fabric not exceeding 4 kg per sqm supplied and fixed with steel angle iron posts complete all as specified and directed.

Mild steel confirming to grade Fe-165 (Fe-290) angle post or struts in fencing fixed independently including cutting and bending to shape as directed drilling holes, notching for wire etc. complete all as specified and directed.

Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of post including securing and tying at crossing with and provision of galvanised mild steel wire staple or steel pins etc. complete all as specified and directed. (Each line wire to be mesured)

Refifing galvanised 2 strand steel barbed wire complete all as specified and directed.

Removing excavated soil material not exceeding 500 m and depositing where directed at a level not exceeding 1.5 m above the base in soil complete all as specified and directed.

Dismantling AC corrugated sheet as in roof covering complete all as specified and directed.

Angles for roof truss with purlin, rafter, struts and post and fixed with angle cleats or other connecting plates confirming to Gde Fe 410-0 or Fe-310-0 complete all as specified and directed.

15 mm thick rendering in cement mortar (1:6) on other than fair face of brick or concrete surface complete all as specified and directed.

Applying two coat birla wall care putty on new plastered on wall surfaces including preparation of surface by brooming down or steel wire brushing, scrapping down vegetation growth, efflorscent salts and trading with oil greasy spot complete all as specified and directed.

Two coats of distempar oil emulsion over a coat of primer including preparation of new plstered surfaces of walls complete all as specified and directed.

Applying two coats of cement based paint over a coat of primer including preparation of new plastered surfaces complete all as specified and directed.

Taking down frames with shutters (without taking off shutters from the frame) area not exceeding 1.5 Sqm Each including iron mangery complete all as specified and directed.

Taking down frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm Each including iron mangery complete all as specified and directed.

Powder coated aluminium anodised window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary jointing cleat glazing clips, rubber packing, anodised aluminium snap beading screws etc. complete all as specified and directed.

300 mm long aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

Butt hinges, 100 mm size extruded aluminium alloy with galvanised mild steel hinge pin, anodised complete all as specified and directed.

150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

100 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

150 mm length aluminium handles fabricated type anodised complete all as specified and directed.

100 mm length aluminium handles fabricated type anodised complete all as specified and directed.

4 mm thick figured glass, pin head type and glazing complete in suares exceeding 0.50 sqm in each pane including glazing clis, rubber acking, powder coated aluminium snap beading, serews complete all as specified and directed.

Aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium staples complete all as specified and directed.

Floor door stoper (140 mm length) of aluminium alloy body complete all as specified and directed.

Door closer hydraulically regulated, designation no 2 universal type suitable for door shutter of 701 to 850 mm in width and of weight between 36 to 60 kg Aluminium (extruded section) body in repair complete all as specified and directed.

Brass mortice lock, vertical type, size 100 mm, 4 leaver complete all as specified and directed.

8 mm thick toughened glass as in railing, partition fixed type including necessary fixings such as silcon gell or other fixing climps complete all as specified and directed by Engr-in-Charge.

Punched tape concertina coil (including spike and handle) with 50 turns and 1050 mm dia, width of barbed 9 mm dia and spacing of clips 23.5 mm to 24.5 mm c/c, weight of coil will be 10 to 14 kg without packing. Coil length will be 6 mtrs when opened up etc. complete all as specified and directed.

Taking down carefully aluminium/copper point wiring complete with (light, fan, socket or power) complete fitting such as switch, sockets, ceiling rose, pendents sockets any type, rectangular board terminal boxes etc and making good disturbed surface of walls, and complete all as specified and directed keeping aside serviceable item for re-use within the same bldg and removing unserviceable item from site.

Point wiring for one light point/fan point/Bell ponit controlled by one switch with 1.5 Sqmm PVC insulated FRLS unsheathed copper conductor single core multi stranded flexible copper cable in and including not less than 1.50 mm thick 20 mm dia & over concealed PVC non metallic rigid PVC conduit (ISI marked) with 1.5 mm thick pressed steel terminal boxes (modular type) concealed for fixing of modular switches/regulator etc along with PVC insulated and insheathed FRLS 1.5 Sqmm multi stranded copper conductor cable (green color) as earth lead in and inculding PVC Concealed Conduit medium grade with all fitting (ISI make), complete all as specified and directed by Engr-in-Charge including modular cover plate with frame, making good the disturbed surfaces to match with the existing specification. Make - Havells or equivalent make in polycab/finolex

All as per ser item No 84 but for 05 amp socket outlets point controlled by one switch on Independent board complete all as specified and directed. Make - Havells or equivalent make in polycab/finolex

All as per ser item No 84 but for 05 amp socket outlets point controlled by one switch on Same board complete all as specified and directed. Make - Havells or equivalent make in polycab/finolex

All as per ser item No 84 but for 3 pin 20 A socket outlet point controlled by one modular switch 20A on the independent board with 2.5 Sqmm size of copper cable as main and 2.5 Sqmm copper cable as earth lead complete all as specified and directed.

Switch button single pole one way 5 amps 240 volt (Modular Type) with outer strip complete all as specified and directed. Note - All modular cover plate/modular flush Box/Switch/ Sockets Incorporated with this, should be in same Make - Havells/phillips/Indoasian

Switch piano fiush button single pole one way 20 amps 240 volt (Modular Type) with outer strip complete all as specified and directed. Make - Havells/phillips/Indoasian

Sockets Combined 2-in-1, 3 pin 6 Amps, 240 Volt flush type (Modular Type) with outer strip complete all as specified and directed. Make - Havells/phillips/Indoasian

Sockets combined 2-in-1, 3 pin 20 Amps, 240 Volt flush type (Modular Type) with outer strip complete all as specified and directed. Make - Havells/phillips/Indoasian

Bell AC, Ding dong, 230 Volts, single pole with all acessories complete all as specified and directed. Make - Havells(crabtree)/phillips /Indoasian

Bell Push, 6 amp, 230 Volts, 1 module (Modular type) complete all as specified and directed. Make - Havells/Phillips

Ceiling rose surface bakelite, 3 terminals complete all as specified and directed. Make - Havells/Indoasian

Replacement fan regulator 120W, 230V 50 C/S, deluxe Modular type electronic, step type hum free suitable control speed of fan from 0 to 100 % and connecting electrically all as required or complete all as specified and directed by Engr-in-Charge. Make - Havells (crabtree)/phillips/Indoaisan

Taking down carefully existing ceilling/exaust fan any type sweep and removing fan blade including cleaning all dust particle and filling cavities with filler material, oiling and assemble the same along with all fixing connecting accessories and fixing the same position along with all new electrical wire connection complete all as specified and directed.

Aesthetically designed, 2x2 LED flat panel 34 watt for surface (including electronic driver) for surface mounting which provides soft-light and glare free symmetrical illumination suitable for (600 x 600 x 70 mm) surface mounting complete making all connection using 1.5 Sqmm copper conductor multistarnd PVC insulated 3 core flexible cable complete all as per the directions of Engr-in-Charge. Make - Havells (Pluto Panel- Surface) Cat Part No - PLUTOSURFA CE2X2PLS34WLED857S

Slim linear LED tube light fixture 20 Watt, with T8 polycarbonate 6500k Housing made of extruded AL with lumen O/P should not be less than 100 lum/watt making all connection using 1.5 Sqmm copper conductor multistranded PVC insulated 3 core flexible cable from ceiling rose to fitting drawn through PVC flexible conduit complete all as specified and directed. Make : Havells Cat Part No : (E-Lite LED Pride Plus Neo) LHEXACP7UN1W020 or equivalent make in Philips/Polycab

Slim linear LED lighting fixture 5 Watt LED Batten, For mirror light purpose, Complete making all connection using 1.5 Sqmm copper conductor multistarnd PVC insulated 3 core flexible cable from ceiling rose to fitting complete all as per the directions of Engr-in- Charge. Make - Havells (E-Lite LED Pride Plus Neo) LHEXBTP7IN1W005 or equivalent make in Philips/Polycab/Cromton

Surface decorative 12 Watt LED Peocock, 6000K, wall/ceiling mounted fixture with electronic driver and opaque diffuser, suitable for indoor applications complete all as specified and directed. Make - Havells, Cat Part No - LHEOFIP7CUZ1W012

10 watt ZOOM downlights (round) WW recessed mounted round COB based fully adjustable LED spot light complete all as specified and directed. Make - HPL, Cat Part No - HLPLEDZRMB10WW

Slim linear decorative, wall mounting, SS finish fixture with opal glass diffuser suitable for LED lamp (Including LED lamp warm white) complete all as per the directions of Engr-in - Charge. Make - Havells Venza Cat Part No - LHJC02108499/Syska LED Cat Part No - SSk-BH-9W/ or equivalent make in Polycab, wipro, C&S.

10 watt LED hexagon bulk head, IP66, Environmental friendly, ultra modern, energy saving, surface mounted, complete making all connection using 1.5 Sqmm copper conductor multistarnd PVC insulated 3 core flexible cable complete all as per the directions of Engr-in- Charge. Make - Havells (Hexa 10 W) Cat Part No - HEXAFT10WLED857SSYMBOPC or equivalent make in Philips/Polycab

Earthing complete with galvanised cast iron earth plate electrode of size 600 x 600 x 6 thick as earth electrode with top edge of earth plate not less than 1.5 m below ground level using GI wire 4 mm dia as earth continuity conductor connected to earth plate by means of GI thimbles nuts bolts washers all as directed inculding providing earth wite protection pipe GI light grade 15 mm dia from earth plate to maln switch board/panal, watering pipe 20 mm dia with mesh and funnel at top, earth pit and RCC pit cover in PCC 1:3:6 adequate quantity of characoal dust and salt all around the earth plate, earth work in any type of soilo remaning surplus excavated material all as required at site and specified in EP no 3 of SSR part I 1991 or complete all as specified and directed by Engr-in-Charge.

Submain wiring with two single core PVC insulated unsheathed, FRLS flexible copper conductor cable of size 10 Sqmm and one single core PVC insulated unsheathed, FRLS flexible copper conductor cable of size 6.0 sqmm as earth lead in & inculding PVC casing /non metallic rigide PVC conduit medium grade and making good the distured at site or complete all as specified and directed by Engr-in-Charge. Make of cable - KEI/polycab/ finolex

Replacement of Sheet metal enclouser single pole and neutral with 2 pin and earth plug and socket 20A 240V complete with one single pole MCB of any cap from 10Amp to 20Amp, 10KA complete all as specified and directed.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Note - MCBs will be measured separately.

Replacement MCB single pole 240 volt any rating from 10 to 32 amps, B-Series, with rupturing capacity 10 KA, inculding providing aluminium thimble for out going cable complete all as specified and directed. Make -Legrand (DX3)/Schneider (Acti-9)/Siemens (Betagard-8GB32)/Indo Asian(optipro)

Replacement MCB Single Pole and Neutral 240 volt any rating from 40 to 63 amps, B-series, with rupturing capacity 10 KA, inculding providing aluminium thimble for out going cable complete all as specified and directed. Make - Legrand (DX3)/Schneider (Acti-9)/ Siemens (Betagard-8GB32)/Indo Asian (opti pro)

VTPN MCCB DB-Double Door (Including 63 Amp MCCB) 16 kA (as Incommer) 4 way double door IP-43 protection complete all as specified and directed. (Including All PCC & Cementing work for installation of TPN DB to Wall, deemed to be quoted rate by contractor)

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of Sqmm 25x3.5 core size complete all as specified and directed including taking down old cable. Note : Earth work and other connected work shall be measured & paid seperately.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth for laying of pipe/cable/foundation of poles & stays in any type of soft /loose soil and getting out etc. complete all as specified and directed by Engr-in-Charge.

Brick covering width equal to length of brick for mechanical protection to cable with well burnt sub class 'B' bricks laid dry flat complete all as specified and directed by Engr-in-Charge.

Sand cushioning for under ground cable provided with a layers of 8 mm high before laying cable and 15 mm thick after laying and stretching the cable complete all as specified and directed by Engr-in-Charge.

Galvanized steel pipe light grade with all fitting laid in trenches or passing through cable/road crossing or fixing along pole with suitable size clamps complete of size 40 mm dia complete all as specified and directed.

LED street Light fitting 35 Watt, New generation energy saving and environmental friendly long life versatile pressure die-cast aluminium IP66 with acrylic, with Heat resistant toughened Glass, Corrosion resistant, complete making all connection with MCB SPN alongwith MCB Box enclosure complete all as per the directions of Engr-in-Charge. Make - Havells Cat Part No - LHETBXU7PAIS035 (ENDURA CITYLITE PLATINUM PLUS)

Street light Bracket complete made of GI pipe of suitable size, medium grade 1.2 m long bent to shape as per site requirement along with MS flat iron clamps with nuts, bolts, washers including grouting the same with wall complete all as specified and directed by Engr-in-Charge.

Geyser (Electric Storage Water Heater) of capacity 25 Ltrs, vertical type Energy Efficient 5 star rating, 230V, SP, AC complete including all GI connection (cutting T, inserting all type of Elbow, Nipple etc.) and all necessary fixing arrangement on existing wall complete all as specified and directed. Make: Havell (Model : Monza DX) or equivalent to Bajal/Philips.

Hanging Ceiling fan 1200 mm sweep complete set without regulator including connecting to ceiling rose with twin twisted flexible cooper cable and provisioning of suitable fan hook/ down rod including all accessories as per site requirement complete all as specified and directed. Make : Havells Model: ES-50 or equivalent to Bajaj/Philips/Crompton.

Exhaust fans size 300mm complete with louvre including grounting of nut bolts for fixing of Exhaust Fan complete all as specified and directed. Make :- Havells Model: Ventil Air - DS or equivalent to Bajaj/Philips/Crompton.

Taking down unserviceable fan and geysers, sealing cable end, dismentling blade and deposit to MES Yard for a safe custody of a removed fan and geysers with all accessories complete all as specified and directed by Engr-in-Charge.

Alishan Builders

SINGH CONST CO

VARDHMAN INTERNATIONAL