Balance work for Construction of Type-2 -06 Nos. and Type-3-06 Nos. Residence at Thana Kothibhar Distt. Mahrajganj

R.C.C. work with cement, approved coarse sand and 20 mm gauge dalla stone aggrigate with M-20 nominal mix 1:1.5:3 in Lintel band of doors and windows excluding the supply of all reinforcement and its bending but including its fixing and binding with 24 BWGGI binding wire, centering and shuttering, supply of all materials, labour and tools and plants etc. required for proper completion of work.

M-150 class brick work 1:6 cement and sand of 2:25 fineness modululous mortar in super structure including supply of all material, labour and tools and plants etc. required for proper completion of work. But in super structure including necessary cutting and moulding of brick work, for one brick 230mm thick wall.

M-150 brick work in 1:4 cement and coarse sand in super structure including necessary cutting and moulding of brick work, but for half brick wall add for extra lbour icluding supply of all materilas,labour and T&P etc. required for proper completion of work.

R.C.C.Work with cement approved coarse sand and 2cm gauge stone girt in the propotion of 1:1.5:3 R.C.C. Lighter Beam. (M-20) in excluding cost of rienforcement (steel) and its banding but including fixing and banding the same with 24 B.W.G.G.I. banding wire and including necessary centering and shuttring etc.& also including supply of all materilas,labour and T&P etc. required for proper completion of work.

R.C.C. work with cement, approved coarse sand and 2 cm gauge approved stone ballast in the proportion 1:1.5:3 in R.C.C. Slab, excluding supply of steel and its bending but including fixing and binding the same with 24 B. W.G.G.I binding wire and including necessary centering and shuttering etc and also including s/o all materials required for proper comletion of the work.

Mild steel or iron work in plain work such as reinforced cement concrete (when not included in over all rate) wrought to required shape as necessary including bending for proper completion of work, supply of steel, all labour etc. required and including wastage bend, hooks and authorised over lapping shall be measured. As per s.i.no. 504

Fabrication supply and fixing of M.S.Angle iron (40x40x5mm) in chaukhats for door, windows and ventilators including using flat iron etc. and 3 mm thick gusset plates at corners and junctions including supply of steel cutting, drilling holes bending, moulding requried shap and welding, supply and fixing of necessary hings for doors 125mm of 14 gauge size, window and ventilator 100mm, 16mm gauge size, with cleats and stoppers etc. and 10 mm dia bottom tie rod etc. complete. DSR 10.31

Fabrication and supply of M.S. grill as per approved design and drawing including the stair case railling etc. with square bars, m.s. angle iron, and m.s. flat iron as per direction of Engineer-incharge, supply of steel and its wastage, cutting, drilling holes and welding joints where necessary including each joint tube perfectaly welded and jointed and grinded to smooth finish. DSR 10.31

Z-sction windows (151 marke) or Z- tubler window made of gold rolled formed continous seam welded M.S. tubler box section made from corrosion resistant coated conforming to IS: 513=1973 size of welded tubuler Z-profile and T profile are glzing bars jointed mitred and flush but welded and lugs 100 mm long of 19 x 3 mm size embedded in cement concrete blocks 150 x 100 x 100 of 1:3:6 cement approved coarse sand and 20 mm nominal size of dalla stone aggregate or with plugs and screws required including fixing 4 mm thick glass panes with glazing and special metal sash putty of approved make complete including M.S. oxidised casement fastercer (125 mm length weighting not less than 240 gms) and box type hinges 65 mm length 2.5 mm thick galvnised pin of 6 mm dia and aplying a priming coat of approved steel primer. DSR 10.31

Fixing of door, window steel chaukhat frame in position and making all arrangement etc. complete. As per N.S.No. 3 chapter 10