Fabrication and installation ofSai head gate on water distribution channel Saifrom lift irrigation station Sai towards Gulabsinghpura of Sai Area at RD 960, fabrication and installation of Sai minor gate- II on water distribution channel number C2 fr

Fabrication and installation ofSai head gate on water distribution channel Sai from lift irrigation station Sai towards Gulabsinghpura of Sai Area at RD 960.

Fabrication and installation of Sai head gate on water distribution channel Sai from lift irrigation station Sai towards Gulabsinghpura ofSai Area at RD 960. by way of dismantling of damaged old gate lifting mechanism from the supporting channel and disconnecting the stem rod from the leaf structure then extracting out the damaged/worn out gate leaf structure with the help of manual labour using tools and tackles, chain pulley block and tripod/hydra crane after removing accumulated mud/silt around the gate leaf. Carriage of gate structure along with winch machine and stem rod to the road with the help of manual labour using tools and tackles. Loading in mechanical transport and then carriage to workshop. Fabrication of leaf structure of size 30 inches x 30 inches(approx) using the ISMC 75channel size with vertical &horizontal cross members for support by way of cutting /welding using superior quality electrodes. The leaf of the gate should have threenumber vertical supports and three number horizontal supports welded together to form the frame. The MS sheet of 5 mm thickness needs to be welded over the fabricated frame of ISMC 75 channel. Making of provision for stem rod attachment with 2 no. L-shaped MS Clamps.Providing, fabrication and fitting of 1 no. stem rod MS bar of length as per the site conditionsand thenturning, threading, finishing to the original size. Fabrication and installation of rubber water seal at the back side of leaf of gate and fastening it with gate to prevent seepage of water. Fabrication of outer frame 48 inch x 60 inch of gate for up and down moment of gate using ISMC 100 channel or angle iron welded together to form . The outer frame should consists of two side channels for up and down moment of gate, bottom sil beam and two channels on top to support the weight of winch machine and gate. The job consists of dismantling of fabrication of grooves as per size of ISMC 100 channel in concrete structure.Then outer structure of the gate have to be fitted in walls of channel with cement and concrete mixture minimum ratio of 1:3:6. Fabrication, providing & fitting of 02 Ton capacity manually operated, worm gear type winch machine along with base plate of 6/8mm thickness.Oiling and greasing the gear and bearings mechanism before fitting. Providing and fitting of rain pipe over the winch machine to secure the stem rod and machinery. Loading the gate structure along with winch machine on the carriage vehicle for carrying to site of installation. Unloading the gate structure at road side then shifting to the site of installation. Installation of gate structure by way of lowering the leaf structure into the sliding grooves using manual labour, tools and tackles using chain pulley block and tripod/crane. Drilling requisite no. of holes in hoisting channels at site. Fitting of winch machine on the supporting channel and connecting the stem rod to the leaf structure after ensuring the proper alignment/gravity of the gate structure. Complete painting of gate structure with coats of red oxide primer and superior quality enamel paint ( Asian paints/ Kansai Nerolac paints/ Berger paints). Complete job includes cost of material, transportation charge, labour charges and testing for its smooth operation at site, cost of sand bags for stopping the flow of water in escape channel during the period of execution of work. Note:- The tenderers are requested to visit the site and quote the rate as per site conditions. Any modifications/ alterations of the job, absolutely necessary if required at the time of execution may be done as per actual site conditions.

Fabrication and installation of Sai minor gate- II on water distribution channel number C2 from lift irrigation station Sai towards Jabowal of Sai Area at RD 960.

Fabrication and installation of Sai minor gate- II on water distribution channel number C2 from lift irrigation station Sai towards Jabowal of Sai Area at RD 960by way of dismantling of damaged old gate lifting mechanism from the supporting channel and disconnecting the stem rod from the leaf structure then extracting out the damaged/worn out gate leaf structure with the help of manual labour using tools and tackles, chain pulley block and tripod/hydra crane after removing accumulated mud/silt around the gate leaf. Carriage of gate structure along with winch machine and stem rod to the road with the help of manual labour using tools and tackles. Loading in mechanical transport and then carriage to workshop. Fabrication of leaf structure of size 60 inches x 33 inches(approx) using the ISMC 75channel size with vertical &horizontal cross members for support by way of cutting /welding using superior quality electrodes. The leaf of the gate should have threenumber vertical supports and three number horizontal supports welded together to form the frame. The MS sheet of 5 mm thickness needs to be welded over the fabricated frame of ISMC 75 channel. Making of provision for stem rod attachment with 2 no. L-shaped MS Clamps. Providing and installation of rubber seal on the leaf of the gate and fastening it leaf structure. Providing, fabrication and fitting of 1 no. stem rod MS bar of length as per the site conditionsand thenturning, threading, finishing to the original size. Fabrication of outer frame 80 inch x 60 inch of gate for up and down moment of gate using ISMC 100 channel or rectangular frame fabricated out of angle iron for smooth movement of gate as per site conditions. The outer frame should consists of two side channels for up and down moment of gate, bottom sil beam and two channels on top to support the weight of winch machine and gate. The job consists fabrication of grooves as per size of ISMC 100 channel in concrete structure.Then outer structure of the gate have to be fitted in walls of channel with cement and concrete mixture minimum ratio of 1:3:6. Fabrication, providing & fitting of 03 Ton capacity manually operated, worm gear type winch machine along with base plate of 6/8mm thickness.Oiling and greasing the gear and bearings mechanism before fitting. Providing and fitting of rain pipe over the winch machine to secure the stem rod and machinery. Loading the gate structure along with winch machine on the carriage vehicle for carrying to site of installation. Unloading the gate structure at road side then shifting to the site of installation. Installation of gate structure by way of lowering the leaf structure into the sliding grooves using manual labour, tools and tackles using chain pulley block and tripod/crane. Drilling requisite no. of holes in hoisting channels at site. Fitting of winch machine on the supporting channel and connecting the stem rod to the leaf structure after ensuring the proper alignment/gravity of the gate structure. Complete painting of gate structure with coats of red oxide primer and superior quality enamel paint ( Asian paints/ Kansai Nerolac paints/ Berger paints). Complete job includes cost of material, transportation charge, labour charges and testing for its smooth operation at site, cost of sand bags for stopping the flow of water in escape channel during the period of execution of work. Note:- The tenderers are requested to visit the site and quote the rate as per site conditions. Any modifications/ alterations of the job, absolutely necessary if required at the time of execution may be done as per actual site conditions.

Fabrication and installation of Sai minor gate- I on water distribution channel C1 from lift irrigation station Sai towards primary health centre of Sai Area at RD 960.

Fabrication and installation of Sai minor gate- I on water distribution channel C1 from lift irrigation station Sai towards primary health center of Sai Area at RD 960,by way of dismantling of damaged old gate lifting mechanism from the supporting channel and disconnecting the stem rod from the leaf structure then extracting out the damaged/worn out gate leaf structure with the help of manual labour using tools and tackles, chain pulley block and tripod/hydra crane after removing accumulated mud/silt around the gate leaf. Carriage of gate structure along with winch machine and stem rod to the road with the help of manual labour using tools and tackles. Loading in carriage vehicle for carriage to workshop. Fabrication of leaf structure of size 56 inches x 35 inches(approx) using the ISMC 75channel size with vertical &horizontal cross members for support by way of cutting /welding using superior quality electrodes. The leaf of the gate should have threenumber vertical supports and three number horizontal supports welded together to form the frame. The MS sheet of 5 mm thickness needs to be welded over the fabricated frame of ISMC 75 channel. Making of provision for stem rod attachment with 2 no. L-shaped MS Clamps.Fabrication and installation of rubber seal with the leaf of gate and fastening it with leaf to prevent the seepage of water. Providing, fabrication and fitting of 1 no. stem rod MS bar of length as per the site conditionsand thenturning, threading, finishing to the original size. Fabrication of outer frame 75inch x 60 inch of gate for up and down moment of gate using ISMC 100 channel or rectangular frame fabricated out of angle iron for smooth movement of gate as per site conditions. The outer frame should consists of two side channels for up and down moment of gate, bottom sil beam and two channels on top to support the weight of winch machine and gate. The job consists of dismantling of fabrication of grooves as per size of ISMC 100 channel in concrete structure.Then outer structure of the gate have to be fitted in walls of channel with cement and concrete mixture minimum ratio of 1:3:6. Fabrication, providing & fitting of 03 Ton capacity manually operated, worm gear type winch machine along with base plate of 6/8mm thickness.Oiling and greasing the gear and bearings mechanism before fitting. Providing and fitting of rain pipe over the winch machine to secure the stem rod and machinery. Loading the gate structure along with winch machine on the carriage vehicle for carrying to site of installation. Unloading the gate structure at road side then shifting to the site of installation. Installation of gate structure by way of lowering the leaf structure into the sliding grooves using manual labour, tools and tackles using chain pulley block and tripod/crane. Drilling requisite no. of holes in hoisting channels at site. Fitting of winch machine on the supporting channel and connecting the stem rod to the leaf structure after ensuring the proper alignment/gravity of the gate structure. Complete painting of gate structure with coats of red oxide primer and superior quality enamel paint (Asian paints/ Kansai Nerolac paints/ Berger paints). Complete job includes cost of material, transportation charge, labour charges and testing for its smooth operation at site, cost of sand bags for stopping the flow of water in escape channel during the period of execution of work. Note:- The tenderers are requested to visit the site and quote the rate as per site conditions. Any modifications/ alterations of the job, absolutely necessary if required at the time of execution may be done as per actual site conditions.

CHENAB ENGINEERING WORKS

GANPATI ELECTRICAL AND MECHANICAL WORKS

SMART TECH AND CO

Rishabh Electricals and Mechanical Works