REPAIR/REPLACEMENT OF CI/DI/GI PIPE LINES, PUMPSET, MOTOR STREET LIGHT, DG SETs, CLEANING OF OVEHEAD/UNDERGROUND SUMPS INCLUDING OTHER CONNECTED WORKS AT ASC CENTRE SOUTH, OLD PCTC, GNC NP LINE, VOC AND VNC AREA UNDER GE CENTRAL BANGALORE

Amount

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr depth for laying of UG cable/GI/CI pipe lines, for foundation etc getting out including forming bottom surface to required level and gradient in soft/loose soil.

Returning and filling in excavated soil including spreading leveling, watering, well ramming in layers not exc 25 cm thick complete.

Removing of excavated materials not exceeding 50 Mtrs and depositing where directed by Engr- in-Charge at a level not exceeding 1.5 Mtrs above the starting point.

M & L for Sand cushioning and covering with clean dry sand in trenches for protection of under ground cables (below, above and around the cable laid in trenches) complete all as specified and directed. (Note: Thickness after punning down shall be measured for payment)

Supply and laying well burnt bricks, locally available best quality bricks laid breath wise across the length of cable in trenches for protection of UG cables complete all as specified and directed.

M&L for rectification of existing defective run lead joints including burning and removing the old defective lead joints and providing new lead joints with all required materials and testing the joints for leakages for 80 mm bore CI/DI pipes complete all as directed. NOTE: - Earth work shall be measured and paid separately under respective items)

All as per item No 06 above but for 100mm dia sluice valve

All as per item No 06 above but for 150mm dia sluice valve

All as per item No 06 above but for 200mm dia sluice valve

Supply and replace sluice valve spindle made out of brass/bronze material suitable for 80 mm bore cast iron sluice valve including replacing perished gland packing, rubber gasket, steel PN-6 check nut, bolts and nuts of suitable size complete all as directed.

All as per item No 10 above but for 100mm dia sluice valve

All as per item No 10 above but for 150mm dia sluice valve

All as per item No 10 above but for 200mm dia sluice valve

S&F in repair for Cl sluice valve, non-rising type conforming to IS-14846, sutiable for 200 mm bore pipe consisting of SS spindle as per IS 6603, Cast iron Body, Dome & Wedge as per IS 210, greasy jute type gland packing, fasteners as per IS 1367, Natural rubber gasket, CI manual hand wheel etc complete double end flanged and drilled, of Class PN-1.6 ( ISI marked) including all jointing materials such as rubber gasket insertion sheet nut ,bolts and washers etc complete all as specified and directed. Make: Kirloskar/Zoloto/Venus/Leader/ Audco/L&T/BIR

All as per item No 14 above but 150 mm bore

All as per item No 14 above but 100 mm bore

All as per item No 14 above but 80 mm bore

M&L for attending break down of pipe line bursting/cracks including excavation in hard / dense soil with the use of Earth moving machinery / labour and taking out old CI /GI/MS defective / misaligned water pipe line of size 200/150/100/80 mm dia bore carefully after discon-nection of joints to a length up to 8 mtr and create bund with excavated earth and dewatering / bailing out water complete with diesel engine driven pump set and positioning the pipe line after repairs, returning filling and removal of surplus soil / excavated material with the help of excavator / proclainer all as directed by Engineer-in-Charge. NOTE : (a) M/L for Lead Joints/ spares / CI /GI specials will be measured and paid separately. (b) M/L for CI / GI/MS pipe, Specials, lead joints etc will be measured and paid separately under relevant Schedule Items. (c) The rate is deemed to include Cost for tool and plant and transportation required for attending the repair work. (d) Disconnecting / dismantling/ cutting the existing pipe line is included in the quoted rate . (e) The rate is inclusive of earth work complete including returning & refilling in any type of strata complete. (f) The breakdown shall be attended within 4 Hrs of intimation round the clock and time of restoration shall be maximum of 8 Hours. The additional manpower required to complete the job in quoted rate is deemed to be included in the quoted.

M & L for CI pipe special of class 'A' and 'B' like tee's bend sockets, collar's of juinctioning coupling etc of any type(flanged or socket/spigot type )all as specified or new position with the help of connecting pieces for sizes upto 200 mm dia CI pipe line all as directed

M/L for replacing 200 mm bore unserviceable cast iron pipe with spigot & socketed ends centrifugally cast class LA ISI marked suitable for lead joint in any length laid in trenches complete all as specified and directed by Engr-in-Charge. NOTE : - Earth work and lead joints shall be measured and paid separately under respective item). Make: LANCO(Sri Kalahasti) /ELECTROSTEEL /JINDAL

All as per item No 20 above but 150 mm bore

All as per item No 20 above but 100 mm bore

All as per item No 20 above but 80 mm bore

S&F in repair for Butterfly valve, non-rising type conforming to IS-14846, sutiable for 100 mm bore pipe consisting of SS spindle as per IS 6603, Cast iron Body, Dome & Wedge as per IS 210, greasy jute type gland packing, fasteners as per IS 1367, Natural rubber gasket, CI manual hand wheel etc complete double end flanged and drilled, of Class PN-1.0 ( ISI marked) including all jointing materials such as rubber gasket insertion sheet nut ,bolts and washers etc complete all as specified and directed. Make: Kirloskar/Zoloto/Venus/Leader/ Audco/L&T/BIR

All as per item No 24 above but 80 mm dia

Supply & Fix in repair of cast iron foot valve 100 mm dia complete with necessary bolts, nuts, washers all as directed.

Supply & Fix in repair of cast iron foot valve 80 mm dia complete with necessary bolts, nuts, washers all as directed.

Disconnecting / Removing existing U/S scale type water level indicator and S&F dial type water level indicator suitable for Over Head Storage tank of height 15 m to 21 m staging complete with central movement plate, counter weight, centre dividing wheels, MS/CRCA enclosure, float and connecting control wire system from tank to indicator etc complete grouted in PCC all as directed including testing and commissioning all as directed.

M&L for fixing in repair Y type Dirt box (strainer) suitable for 150 mm bore iron pipe, made out of CI with necessary washout arrangement complete including necessary additions & alterations to pipe incl cutting, gaskets & GI nut bolts & washers etc complete all as directed. Note:- CI/MS pipe/ Specials if required will be measured & paid separately.

All as per item No 29 above but 100 mm bore

Supply and fix in repair 20 mm bore gun metal gate valve with iron wheel head screwed both ends for iron pipe of size including dismantling old one. Make: Leader/ Zoloto/L&T/AUDCO

All as per item No 31 above but 25 mm bore.

All as per item No 31 above but 40 mm bore.

All as per item No 31 above but 50 mm bore.

Taking up or down old GI water mains 40 mm to 50mm dia (including all fittings), all specified and directed by engr-in-charge at site. Note : Earth work shall be measured and paid seperately under relevant item.

All same as item No 35 above but for 20mm to 25 mm bore pipe.

Supply and laying GI water tubing 20 mm bore "medium grade" including all fittings to laid in trenches including necessary cuttings, threading and testing on completion all as specified and directed by Engr-in-Charge.

All as per item No 37 above but 25 mm bore.

All as per item No 37 above but 40 mm bore.

All as per item No 37 above but 50 mm bore.

Relaying/refixing of old serviceable steel water tubing and connection in new or old position including necessary cuttings, threading and providing new fittings such as bends, elbows, sockets, nipples, tappers and reducers etc and testing on completion complete all as directed for 20 mm bore pipe Note :- (i) Excavation and earth work will be measured and paid separately. (b) Old serviceable water tubing retrieved under item No above shall be used.

All as per item No 41 above but 25 mm bore.

All as per item No 41 above but 40 mm bore.

All as per item No 41 above but 50 mm bore.

Dismantling of old U/S valve pit of size 120x120x90 Cm ( internal dimensions of the chamber) including and removing the debris at a distance not exceeding 50 Mtr and M/L for brick massonary with cement mortar with 1: 6 , 23 cm and flush pointing externaly work proceeds in the same mortar complete ( using 30% old bricks & 70% New bricks) complete with the following specifications and as directed by Engr-in-Charge. Note :-(i) 10mm thick plaster internally in CM 1:6.(ii) Flooring 40mm thick in PCC 1:2:4 type B-1 over 75mm thick hard core of guage not exc 63mm thick. (iii) Angle iron frame 40X40X6mm thick for cover made out of 3 mm thick mild steel sheet including locking arrangement, handle and necessary hinges etc, (iv) PCC 1:3:6 type C-2 100mm thick in foundation .(v) Two coat of synthetic enamel paint to frame & cover internally and externally over a paint of Red Oxide primer.

All as per item No 45 here-in- before but of size 100x100x105 cm

All as per item No 45 here-in- before but of size 90x90x105cm

Supply and fixing in repair Rubber gasket joint suitable for 150 mm bore cast iron/DI pipes all as specified and directed.

Supply and fixing in repair Rubber gasket joint suitable for 80 mm bore cast iron/DI pipes all as specified and directed.

S&F in repair Cl swing check NRV conforming to IS-5312, sutiable for 100 mm bore pipe consisting Cast iron Body, door as per IS 210, Bronze body ring as per IS 318, natural rubber door face, hinge pin SS ASTM A276 type 410, fasteners as per IS 1367, Natural rubber gasket, etc complete double end flanged and drilled, of Class PN-1.6 ( ISI marked) including all jointing materials such as rubber gasket insertion sheet nut ,bolts and washers etc complete all as specified and directed.

S&F in repair Cl swing check NRV conforming to IS-5312, sutiable for 80 mm bore pipe consisting Cast iron Body, door as per IS 210, Bronze body ring as per IS 318, natural rubber door face, hinge pin SS ASTM A276 type 410, fasteners as per IS 1367, Natural rubber gasket, etc complete double end flanged and drilled, of Class PN-1.6 ( ISI marked) including all jointing materials such as rubber gasket insertion sheet nut ,bolts and washers etc complete all as specified and directed. Make for item No 50 & 51 : - Make: Kirloskar/Zoloto/Venus/Leader/ Audco/L&T/SHANT

Material and labour PCC 1:4:8 type -D2 using 40mm graded aggregate in fdn filling and mass complete for pipe line supports or any indicated position all as specified and directed by Engr-in-charge.

M & L for dismantling of motor of 20 HP to 30 HP capacities pumpset from installed position after disconnecting the coupling and electric connections and transporting the motor to the work shop, strip opening of the motor complete incl dismanlting stator, rotor assembly and cleaning the complete assemblies by taking out perished glass sleeve of connecting leads from common termination to terminal block,and washing with carbon tetra chloride, decarbonising and cleaning the rotor with CTC solution.Replacing the glass sleeve of connecting leads from common termination to terminal block, binding the loose coils with binding cloth, varnishing the coils complete and applyng bectol on the excitor coils, stator coils and heating complete, reassembling the unit and testing with megger for insualtion value and re-assembling, aligning with pump, re-inserting shims where necessary, refixing with coupling, tightening with torque wrench to required level, complet painting of motor /pump re-connecting the electric cable etc and check for drawing current testing, commissioning etc all as directed by Engineer-in-Charge.

All same as item No 53 above but for 10HP to 15 HP pump set.

All same as item No 53 above but for 5HP to 7.5 HP pump set.

M & L for dismantling the pump of 20 HP to 30 HP capacity, checking the worn out parts like impeller, shaft, stuffing box, shaft sleeve using Micrometer and transporting to workshop for repairs, check for condition of bearings, removing scales from impeller and pump housing, building the worn out metal of transmission shaft to required level, machining to the required size on lathe machine, grinding and finishing to match the sleeve, and fixing into the housing, re-assembling, transport back to the installation, installing in position, check for alignment with dial gauge, inserting shims where necessary, refixing with coupling, tightening with torque wrench to required level, re-connecting the flanged pipe connections of suction/ delivery including replacement of rubber insertion, complet painting of motor /pump etc complete, all as directed by Engineer-in-Charge. NOTE :- Spares will be measured and paid separately under relevant schedule.

All same as item No 56 above but for 10HP to 15 HP pump set.

All same as item No 56 above but for 5HP to 7.5 HP pump set.

Supply only Shaft bushes with check nuts (stainless steel) for pumpset of capacity 20 to 30 HP.

Supply only Ball bearings suitable for pumpset of capacity 20 to 30 HP. Make : NBC / SKF.

Supply only Metal Coupling for pumpset of capacity 20 to 30 HPt.

Supply only Gland packing end cover (Stainless steel of suitable grade) as per existing size for pumpset of capacity 20 to 30 HP

Supply only star rubber Coupling for pumpset of capacity 20 to 30 HP.

Supply only Shaft bushes with check nuts (stainless steel) for pumpset of capacity 10 to 15 HP.

Supply only Ball bearings suitable for pumpset of capacity 10 to 15 HP. Make : NBC / SKF.

Supply only Metal Coupling for pumpset of capacity 10 to 15 HP.

Supply only Gland packing end cover (Stainless steel of suitable grade) as per existing size for pumpset of capacity 10 to 15 HP

Supply only star rubber Coupling for pumpset of capacity 10 to 15 HP.

Supply only Shaft bushes with check nuts (stainless steel) for pumpset of capacity 5 to 7.5 HP.

Supply only Ball bearings suitable for pumpset of capacity 5 to 7.5 HP. Make : NBC / SKF.

Supply only Metal Coupling for pumpset of capacity 5 to 7.5 HP.

Supply only Gland packing end cover (Stainless steel of suitable grade) as per existing size for pumpset of capacity 5 to 7.5 HP

Supply only star rubber Coupling for pumpset of capacity 5 to 7.5 HP.

M&L for dismantling the defective induction motor of 20 HP to 30 HP capacity of any make/class of insulation from foundation bed, duly coupled with pump/compressor, trasnporting to workshop removing burnt out winding from stator/rotor, rewinding with suitable gauge of super enamelled copper wire of approved make and replacing DE /NDE bearings, insulation materials, varnishing , heating, complet painting of motor etc complete, re-assembling, testing and commissioning of motors in existing location complete all as directed.

All as per item No 74 above but motor capacity 10 HP to 15 HP.

All as per item No 74 above but motor capacity 5 HP to 7.5 HP.

Renewal of rubber bush coupling suitable 20 HP to 30 HP capacity pumpsets complete all as directed.

All as per item No 77 above but motor capacity 10 HP to 15 HP.

All as per item No 77 above but motor capacity 5 HP to 7.5 HP.

S&F in replacement fully automatic star delta motor starter with Spp suitable for 20 to 30 HP motor . Make:-GE / BCH /SIEMENS /C&S /Havells/L&T

S&F in replacement fully automatic star delta motor starter suitable for 10 to 15 HP motor . Make:-GE / BCH /SIEMENS /C&S /Havells/L&T

S&F in replacement fully automatic star delta motor starter with Spp suitable for 5 to 7.5 HP motor . Make:-GE / BCH /SIEMENS /C&S /Havells/L&T

Servicing/Repair of Star delta starter of any capciity/make including checking the all electrical connections ,fuse, SPP,relays,contactor etc .Note: The quotated rate shall be included the all items exacept Conactor and OLR.

Supply and replace power contactor of type ML-2 /MNX equivalent of L&T make or GE complete all as directed.

S&F in replacement Direct-on -line motor starter, type MK1 of L&T make or equivalent in C&S/ BCH/ GE.

Supply and fix in replacement Thermal overload relay of range 45-75A. Make:- GE/SIEMENS/L&T/ABB/JVS/AVIAVA

Supply and fix in replacement Thermal overload relay of range 66-110A. Make:- GE/SIEMENS/L&T/ABB/JVS/AVIAVA

Supply and replace pressure gauge 0-10 kg/cm² ,4" dia internal glycerin filled including stop cock etc complete with necessary fittings incl disamntling old one all as directed. Make:- H-GURU /FIE BIG

Supply and replace pressure gauge 0-50 kg/cm² ,4" dia internal glycerin filled including stop cock etc complete with necessary fittings incl disamntling old one all as directed. Make:- H-GURU /FIE BIG

Dismantling rusted/defective LT panel doors/canopy and M&L for new LT panel doors of size all as per existing with 2 mm / 3.15 mm thickness MS sheet, hinges, locking arrangement etc complete including replacement of neoprene gasket and painting with a coat of of red oxide primer complete all as directed by Engr-in-Charge

Material and labour for cleaning of over head water tank of 2.00 Lakh and above gallons capacity at 15m height staging at ASC(S) by pumping out the accumulated water at the bottom and removing the complete silt from the sump and depositing and levelling as directed and cleaning the tank with the bleaching powder and wire brush after scrapping the walls and bottom of the sump completely without disturbing the water supply to the area including painting the details of sump capacity, date of cleaning and due date of cleaning on the sump wall and applying one coat of white wash to entire sump internally complete all as directed by Engineer-in-Charge.

Material and labour for cleaning of over head water tank of 1.00 Lakh and above gallons capacity at 15m height staging at VOC by pumping out the accumulated water at the bottom and removing the complete silt from the sump and depositing and levelling as directed and cleaning the tank with the bleaching powder and wire brush after scrapping the walls and bottom of the sump completely without disturbing the water supply to the area including painting the details of sump capacity, date of cleaning and due date of cleaning on the sump wall and applying one coat of white wash to entire sump internally complete all as directed by Engineer-in-Charge.

All as per item No.92 here-in-before but 0.30 Lakhs gallons capacity semi under ground sump at ASC(S) P/H.

All as per item No. 92 here-in-before but 0.75 Lakhs gallons capacity semi under ground sump at ASC(S) P/H.

All as per item No. 92 here-in-before but 0.10 Lakhs gallons capacity semi under ground sump consisting of three compartments at Naval Park.

Taking down and lowering the serviceable/new column pipe by using borewell lifting mechanical crane including necessary lifting tools/accessories complete all as specified and as directed. Note : Supply of column pipe with collar shall be measured and paid separately under relevant items.)

Supply only borewell column pipe of 50 mm bore dia , heavy duty.

Heavy duty collar suitable for lowering GI Pipe of size 50 mm bore fixed in repairs.

Servicing of submersible pump set 5/7.5 HP capacity including replacing of impeller, guide rings, neck rings, IP bush, bolts & nuts and lathe work etc complete all as directed. Note : (a) Rewinding of motor if required will be measured and paid separately.(b) Quoted rate shall deemed to be included the cost of removing and refixing of motor before and after rewinding/servicing.

All as per item No 99 herein before but 10.0 HP capacity submersible Pump Set.

All as per item No 99 herein before but 12.5/15.0 HP capacity submersible Pump Set.

Rewinding of submersible motor of 5/7.5 HP capacity, 3 phase, with super enamelled PVC insulated copper winding wire including appropriate class of insulation to the existing class and testing on full load after complete re-installation to the satisfaction of Engr-in-Charge. Note : (a) Testing of submersible pump set to be carried out at MES Pump House without extra cost before installation into borewell.(b) Quoted rate shall deemed to be included the cost of removing and refixing of motor before and after rewinding/servicing.

All as per item No 102 herein before but 10.0 HP capacity submersible Pump Set.

All as per item No 102 herein before but 12.5/15.0 HP capacity submersible Pump Set.

Supply on Flat copper cable 3 core 16 Sqmm multistranded conductor for submersible pump fixed in repairs and testing complete.

Supply on Flat copper cable 3 core 10 Sqmm multistranded conductor for submersible pump fixed in repairs and testing complete.

Supply on Flat copper cable 3 core 6 Sqmm multistranded conductor for submersible pump fixed in repairs and testing complete.

Servicing of chlorination plant of any capcity and make of Motor ,nozzele and steerer including replacing of items are required for service condiations etc complete all as directed. N

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, GI strips armoured cable for working voltage 1100 volts, PVC insulated ,2 core, nominal cross sectional area of main conductor 10 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, culverts, under floors, through GI Pipe complete all as specified and as directed.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, GI strips armoured cable for working voltage 1100 volts, PVC insulated ,4 core, nominal cross sectional area of main conductor 10 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, culverts, under floors, through GI Pipe complete all as specified and as directed.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, GI strips armoured cable for working voltage 1100 volts, PVC insulated ,2 core, nominal cross sectional area of main conductor 16 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, culverts, under floors, through GI Pipe complete all as specified and as directed.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, GI strips armoured cable for working voltage 1100 volts, PVC insulated ,4 core, nominal cross sectional area of main conductor 25 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, culverts, under floors, through GI Pipe complete all as specified and as directed.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, GI strips armoured cable for working voltage 1100 volts, PVC insulated ,3 core with reduced neutral conductor (3 1/2 Core), nominal cross sectional area of main conductor 25 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, culverts, under floors, through GI Pipe, in pole complete all as specified and as directed.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, GI strips armoured cable for working voltage 1100 volts, PVC insulated ,3 core with reduced neutral conductor (3 1/2 Core), nominal cross sectional area of main conductor 50 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, culverts, under floors, through GI Pipe, in pole complete all as specified and as directed.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, GI strips armoured cable for working voltage 1100 volts, PVC insulated ,3 core with reduced neutral conductor (3 1/2 Core), nominal cross sectional area of main conductor 70 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, culverts, under floors, through GI Pipe, in pole complete all as specified and as directed.

S & F in repair 25mm bore GI pipe "light grade" for protection & passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings, two coats of aluminium paint over a coat of zinc chromate primer complete all as specified.

S& F in replacement MCCB, 4 pole, 415 volts, 25 kA breaking capacity, 40 Amps with adjustable thermal and adjustable megnetic release fix in existing panel with spader line and other acessories complete all as directed.

S& F in replacement MCCB, 4 pole, 415 volts, 25 kA breaking capacity, 63 Amps with adjustable thermal and adjustable megnetic release fix in existing panel with spader line and other acessories complete all as directed.

S& F in replacement MCCB, 4 pole, 415 volts, 25 kA breaking capacity, 100 Amps with adjustable thermal and adjustable megnetic release fix in existing panel with spader line and other acessories complete all as directed.

S& F in replacement MCCB, 4 pole, 415 volts, 25 kA breaking capacity, 160 Amps with adjustable thermal and adjustable megnetic release fix in existing panel with spader line and other acessories complete all as directed.

Supply and fixing in repair street light controll digital type time switch 40 A, 3 pole 230 Volts single phase rating pole mounted outdoor type totally enclosed including fixing arrangement with MS flat clamp 2 nos with bolts, nuts complete connection all as directed. MAKE : - L&T/Havells/Legrand/ABB

Trimming of tree branches around the HT or LT overhead conductor, poles & stays (not less than 3 metre) to clear the approach of overhead lines including removing of nest, wild grass creepers, unwanted vegetation, etc from pole/stay including cleaning of creepers climbed on poles and angles, channels and disposed off from site to nearby waste deposit complete all as specified and directed by the Engr-in-Charge. (Note : Horizontal distance of tree touching to overhead line shall be measured and paid.)

S & F in repair LED post top of 15 Watt (RUBYMINI of Havells make) new generation energy saving and environmental friendly long life aesthetically design with symmetrical light distribution spun aluminium landscape luminaire with high power LED as light source, IP-65 fixed on existing Gate post using new bolts nuts clamps connecting up by using 2.5 Sqmm copper conductor, multi-stranded copper conductor cable of required length complete all as specified and directed. (Make:- Havells Cat No RUBYMINIPT15WLED830PSYMTOPC or equivalent model of Bajaj/Philips/CG/Wipro/Eveready as approved).

S&F in repair energy saving environmental friendly long life, with highly effective and efficient luminaire robust design LED street/building security light 1x 45 Watt LED pressure die-cast aluminium, heat resistant, toughened glass diffuser, IP65/66 and wired with all accessories connection up with 3 core flexible copper conductor cable 4/20 mm size, 1.5m long and testing on installation all as specified and directed. Make: Havell's Cat No. ENDURASUNDOWNSL45WLED765PASYBOPC or equivelant of make Bajaj/Philips/CG/Wipro/Eveready as approved bu GE.

S&F in repair energy saving environmental friendly long life, with highly effective and efficient luminaire robust design LED street/building security light 1x 60 Watt LED pressure die-cast aluminium, heat resistant, toughened glass diffuser, IP65/66 and wired with all accessories and connection up with 3 core flexible copper conductor cable 4/20 mm size, 1.5m long and testing on installation all as specified and directed. Make: Havell's Cat No. ENDURAOMNIPLUSSL60WLED757SASYTOPC or equivelant of make Bajaj/Philips/CG/Wipro/Eveready as approved bu GE.

S & F in repairs Integral compact wide beam high performance LED flood light luminiaire with IP 66 protection, tampered protective toughened glass 5mm thick, thermal shock impact resistance cover, epoxy black powder coated finish, high purity , 120W LED 5000K high power LED of luminous efficiancy greater than 120 Lm/watt with built in control gear fixed to pole/wall, etc and testing complete all as specified and directed. (Make : HAVELLS Model No - JETAIRISFL120WLED757APWBLTG or equivelant model of make Bajaj/Philips/CG/Wipro/Eveready as approved bu GE.).

S & F in repair Street light bracket arm of length not less than 1.5 m made out of GI tubing, 40 mm bore, light grade fixed to pole, etc with 2 pair 50X3mm size MS flat iron clamp, nuts, bolts including painting with two coats of aluminium paint over a coat of red oxide, zinc chrome primer in MS clamp complete all as specified and directed.

S&F in repair street light thermoplastic cable Junction box made of SMC/FRP of size 240x130x110mm, IP-66, weather proof for outdoor use with TPN terminal and with MCB SP, 6-32A, 10 KA, 'C' Curve, 01 No and connector terminal 4 pole indicating RYB Phase Colour and Neutral colour complete fixed to street light pole with suitable size of mild steel clamps, nuts & bolts complete all as specified and directed. (Make - SINTEX or equivalent model of make as per list of manufacturer attached).

Supply and fixing in repair PVC insulated three core 1.5 sqmm cable stranded copper conductor flexible cable with earth conductor complete all as directed.

S&F Rigid non-metallic PVC conduit of 20mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and directed.

Taking down and repair at site HPSV(sodium vapour)/LED/MV lamp street light fittings (25/45/60/70/150/160/200/250 watt, 230/240 volt of any make) and refixing the same in existing position after cleaning, dusting internally, externally including cleaning acrylic cover, replacement of unserviceable/defective part (s) of the fittings such as SV Lamp, Ballast, ignitor, capacitor, driver etc as required to make the fittings in smooth serviceable condition and testing complete and as directed. (Note: (i) Replacement of unserviceable parts shall be measured and paid seperately as "supply only" (ii) Replacement of worn out cables as per existing size and type including cost of nuts, bolts, washers etc shall deemed to be included in the unit quoted rate of this item)

"Supply only" Ballast with copper winding suitable for street light, HPSV Lamp 150 Watts and voltage tapping at 220/240 volt complete all as specified and directed (Make : Havells/Surya Roshni/Bajaj/Cromption/Philips)

"Supply only" ignitor for HPSV lamp fittings of 70/150/250 watt complete all as specified and directed (Make : Havells/Surya Roshni/Bajaj/Cromption/Philips)

"Supply only" HPSV lamp 150 Watts,230 Volts complete all as specified and directed (Make : Havells/Surya Roshni/Bajaj/Cromption/Philips)

"Supply only" capacitor 20 MFD suitable for street light, 150 Walls HPSV lamp complete all as specified and directed (Make : Havells/Surya Roshni/Bajaj/Cromption/Philips)

Supply only LED driver 240 volts 200 watt for street light/ flood light complete all as directed. MAKE : -SURYA ROSHNI/ BAJAJ/HAVELLS/CG/WIPRO

Supply only LED driver 240 volts 150/160 watt for street light/ flood light complete all as directed. MAKE : -SURYA ROSHNI/ BAJAJ/HAVELLS/CG/WIPRO

Supply only LED driver 240 volts 100/120 watt for street light/ flood light complete all as directed. MAKE : -SURYA ROSHNI/ BAJAJ/HAVELLS/CG/WIPRO

Supply only LED driver 240 volts 70 watt for street light complete all as directed. MAKE : -SURYA ROSHNI/ BAJAJ/HAVELLS/CG/WIPRO

Supply only LED driver 240 volts 60 watt for street light complete all as directed. MAKE : -SURYA ROSHNI/ BAJAJ/HAVELLS/CG/WIPRO

Supply only LED driver 240 volts 45 watt for street light complete all as directed. MAKE : -SURYA ROSHNI/ BAJAJ/HAVELLS/CG/WIPRO

Supply only LED driver 240 volts 35/25 watt for street light complete all as directed. MAKE : -SURYA ROSHNI/ BAJAJ/HAVELLS/CG/WIPRO

Dismantling DC dynamo/alternator of battery charging system 12/24V complete servicing including replacement of bushes, bearings, Carbon brushes, diodes any other minor parts required all as directed & fixing on engine testing/commissioning complete for any capacity of DG Set

Replacement of unserviceable contactor AC operated 4 pole 415 Volt suitable for DG Set 62.5 KVA as per the existing type and model in the AMF panel complete all as specified and directed.

Replacement of unserviceable contactor AC operated 4 pole 415 Volt suitable for DG Set 40 KVA as per the existing type and model in the AMF panel complete all as specified and directed.

Replacement of unserviceable contactor AC operated 4 pole 415 Volt suitable for DG Set upto 20 KVA as per the existing type and model in the AMF panel complete all as specified and directed.

Replacement of fuel pipe PVC metal braided all as per existing length fitted with benzo adopters to both sides with benzo bolts & washers.

Repair and Maintenance of existing canopy of eco friendly DG Set cleaning of internal & external parts, tightening of loose parts, replacing of unserviceable door locks and keys, replacing of damaged or burned inside sponge insulations complete all as directed.

Repair /replacement of PCB board of 15 to 100 KVA DG Set as per existing make and model complete all as specified as directed

Dismantling self starter of engine of DG set capacity 15 KVA upto 100 KVA & repairing the starter by replacing carbon brushes, bearings, solenoid coil, brush, brush holders complete rewinding,servicing refixing after repair, testing/commissioning complete all as directed by Engr-in-Charge.

S & F battery charger of 12/24V 15Amps SCR controlled battery charger 12V /24V 15A with TRICKLE and BOOSTING facility, DC voltmeter, Ammeter, toggle switch etc in charge necessary connection from AC supply to Battery Charger and DC wiring to the battery with crocodile clip etc as required complete all as specified and as directed. Make : M/s. Naren or equivalent make as approved by Engineer in charge .

Replacement of Door hinges for DG Set canopy complete all as specified and directed.

Supply only Battery lead suitable for Battery 12 Volt 180AH alongwith copper lugs and colour of Red and Black for +ve and -ve with brass terminal.

Supply and fix digital voltmeter 0 to 500 volts including taking out unserviceable voltmeter complete all as specified and as directed. Make-MECO/L&T/IMP/SALZER

Supply and fix digital ampermeter 0 to 600 Amps including taking out unserviceable ampermeter complete all as specified and as directed. MECO / L&T/ IMP / SALZER

Supply and fixing in replacement of battery 12 Volts, upto 100 Ah as per the site requirement for DG Sets all as specified and directed. Make: Exide or equivelent as approved by GE.

M&L for carrying out 'B' check for DG set 62.5 KVA, as per manufacturer's recommendation including replacement of Fuel filter, Oil filter, 'O' rings, Fuel pipe, engine oil, gasket, coolant etc complete.

M&L for carrying out 'B' check for DG set 40 KVA, as per manufacturer's recommendation including replacement of Fuel filter, Oil filter, 'O' rings, Fuel pipe, engine oil, gasket, coolant etc complete.

M&L for carrying out 'B' check for DG set 20 KVA, as per manufacturer's recommendation including replacement of Fuel filter, Oil filter, 'O' rings, Fuel pipe, engine oil, gasket, coolant etc complete.

M&L for carrying out 'B' check for DG set 15 KVA, as per manufacturer's recommendation including replacement of Fuel filter, Oil filter, 'O' rings, Fuel pipe, engine oil, gasket, coolant etc complete.

M & L Earthing complete of machinery/equipment installed at power house/substation with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 3.0 m below normal ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected to galvanised earth strip 32 x 6mm thick by means of bolts, nuts, check nuts and washers protected by 40mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 300x300x50mm reinforced with 8mm dia TMT steel bars @15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers,necessary earth work in any type of soil all as shown in Electrical Plate No 3 of MES Schedule Part I, earth lead connected to main switch board or main control board all as directed and testing on completion including taking down old unserviceable earthing. (Cost of earthing deemed to to be included upto 7.5 metre long GI earth strip and GI protection pipe including fittings. Earth pit shall be at min 500mm away from external face of building.)

NAVREET CONSTRUCTION

Chandana Enterprises

M/S - KRUPA ELECTRICALS

Shanthi Construction