CONSTRUCTION OF 2X50 MVA , 132/33KV SUB-STATION AT NATHKUCHI ALONG WITH ASSOCIATED TRANSMISSION LINES UNDER AIFA SCHEME

Amount

Power transformer

40/50 MVA, 132/33 kV, 3-Ph, YNyn0, Z =10 %, ONAN/ONAF with copper wound Power Transformer with OLTC(+5% to -15% in steps of 1.25%) , RTCC panel including all cabling & 10% spare oil.The Transformer shall be suitable for single / twin ACSR MOOSE Conductor termination on HV and twin ACSR MOOSE conductor on LV side. The transformer will be supplied with Bushing mounted NCT on HV & LV side as per the CT ration given in the SLD.The Transformer shall be suitable for outdoor installation & complete with all accessories to meet the technical specification.

250 kVA, 33/0.433 kV, Copper Wound, 3ph, Dyn-11, Z=4% outdoor type "Station Transformer" with OFF Circuit Tap Changer , -5% to + 5 % in steps for 2.5 % & including 10 % spare oil.MV connection shall be through single ACSR MOOSE Conductor, LV Side shall be connected through XLPE Insulated LT cable.

132kV Equipment

145 kV, 3150 A, SCR 40 kA for 1 sec, SF6 Circuit Breaker, outdoor type, 3-Ph gang operated complete with operating mechanism & support structure with 10 % spare SF-6 gas.

145 KV, 1250 A, 40 kA for 1 sec, 3-Ph gang operated Double Break Centre Post rotating , outdoor type , motor operated Disconnector (Isolator) complete without solid core post Insulator.

Without earth switch

With one earth switch(manual)

With Two earth switch(manual)

With one earth switch(manual) Tandem type

145 KV Outdoor type, live tank, single phase Current Transformer as per the details below: The CT shall meet the technical specification & other design requirement as per design requirement.

Transformer feeder CTR : 600-300/1-1-1-1 A

Line & Bus Coupler CTR: 600-300/1-1-1-1 A

145 kV, 1-ph, Capacitor Voltage Transformer (CVT) for 132 kV Incoming Line (132kV/√3/110/√3/110/√3V/110/√3V) as per technical specification.

145 kV, 1-ph, Potential Transformer (PT) on BUS (132kV/√3/110/√3/110/√3V110/√3V) as per the technical specification.

120 kV, 10 kA, Metal Oxide type, heavy duty, station class 3, Lightning Arrestor complete with Surge Counter & flexible copper connecting lead.

145kV BPI for Buswork

145kV BPI for Isolators

CT, CVT & PT JB complete with 30 nos Disconnecting type Terminals Blocks, complete with wiring.

Bay Marshalling Kiosk, made of 2.5 mm. thick sheet steel, protection class IP 55 complete with 250 TB

String Insulator Hardware for 132 kV

Single Tension Insulator assembly suitable for 11 kV, 90 kN Disc Insulator with all hardwares accessories for twin ACSR MOOSE conductor ( without disc Insulator) with turn buckle.

Single Tension Insulator assembly suitable for 11 KV, 90 kN Disc Insulator with all hardwares accessories for twin ACSR MOOSE conductor ( without disc Insulator) without turn buckle.

Single Suspension Insulator assembly suitable for 11 KV, 70 kN Disc Insulator with all hardwares accessories for twin ACSR MOOSE conductor for through type ( without disc Insulator)

Single Suspension Insulator assembly suitable for 11 KV, 70 kN Disc Insulator with all hardwares accessories for single ACSR MOOSE conductor for through type ( without disc Insulator).

Single Suspension Insulator assembly suitable for 11 KV, 70 kN Disc Insulator with all hardwares accessories for single ACSR MOOSE conductor for Drop type ( without disc Insulator).

Single Tension Insulator assembly suitable for 11 KV, 90 kN Disc Insulator with all hardwares accessories for single ACSR MOOSE conductor ( without disc Insulator) with turn buckle.

Single Tension Insulator assembly suitable for 11 KV, 90 kN Disc Insulator with all hardwares accessories for single ACSR MOOSE conductor ( without disc Insulator ) without turn buckle.

Single Suspension Insulator assembly suitable for 11 KV, 70 kN Disc Insulator with all hardwares accessories for Twin ACSR MOOSE conductor for Drop type

90 KN Disc Insulator , B & S type for the String Insulator (Tension) with 5% spare

70 KN Disc Insulator (Suspension) with 5% spare

ACSR MOOSE conductor

Terminal connectors for 132kV side. The Quantity of Terminal connectors shall be as per substation layout & shall be supplied as per technical specification as per individual equipment requirement

Terminal connector for 145kV Isolator to receive single ACSR MOOSE Conductor.

Terminal connector for 145kV SF6 Circuit Breaker to receive single ACSR MOOSE Conductor

Terminal connector for 145kV Current Transformer terminal to receive single ACSR MOOSE Conductor

Terminal connector for 145kV CVT terminal to receive Single ACSR MOOSE Conductor

Terminal connector for 145kV PT terminal to receive Single ACSR MOOSE Conductor

Terminal connector for 145kV BPI to receive single ACSR MOOSE Conductor

Terminal connector for Wave-trap to receive single ACSR MOOSE Conductor

Terminal connector for 120kV Lightning Arrester to receive Single ACSR MOOSE Conductor

Transformer Bushing Connector ( 145kV Side )

Terminal connector for NCT suitable for 50x6 mm CU flat

Spacer for twin ACSR MOOSE with 250mm sub conductor spacing, rigid

C-Wedge connector for twin ACSR MOOSE

C-Wedge connector for single ACSR MOOSE

T- type connector suitable for single ACSR MOOSE through and same T-off

Shield Wire & Accessories

7/3.15 mm GSS wire for shielding

Tension Fittings for 7/3.15mm Earth wire

Earth Wire Connector (PG Clamps)

Cleat Clamp for clamping 7/3.15 mm GSS wire on to the Structure

Pad Clamp for clamping 7/3.15 mm GSS wire on to the Structure for earthing

33 kV Equipment The equipment shall be suitable for outdoor installation and shall meet the technical requirement as per specification for 33 kV , 50 Hz, 31. kA/3 Sec., Creepage as 25 mm / Kv

36 kV, 1250 A, SCR 31.5/3sec, SF6, Outdoor type, 3-Ph gang operated complete with operating mechanism & support structure for Incoming Feeders & Bus coupler.

36 kV, 1250 A, SCR 31.5/ 3 sec , SF6, Outdoor type, 3-Ph gang operated complete with operating mechanism & support structure for Outgoing Feeders.

36 KV,1250 A, 3-Ph gang operated, Outdoor type, Double Break centre Post rotating outdoor type motor operated Disconnector (Isolator) without solid core Post Insulator.

Without earth switch for Incomer from Transformer

With one earth switch for Bus Coupler

Outdoor type 36 kV, 630 A, 3-Ph gang operated, outdoor type, Double Break centre Post rotating outdoor type motor operated Disconnector (Isolator) with solid core Post Insulator.

With one earth switch

Without earth switch

36 kV Out door type, live tank, single phase Current Transformers as given below:The CT shall meet the technical specification & other design requirements.

36 kV Transformer side & Bus Coupler CTR:1200-600 /1-1-1 A

36 kV outgoing Line Feeder CTR:1200-600/1-1-1 A

15 kV Neutral Current Transformer for 132/33 kV transformer on 33 kV side, CTR1200-600/1 -1A

Outdoor type 36 kV ,1-ph, Potential Transformer(PT) (33kV/√3/110/√3/110/√3V) as per technical specification

30 kV,10 kA, Metal Oxide type, heavy duty, station class Lightning Arrestor complete with Surge Counter & copper connecting lead

33 kV, 8 kN Post Insulator (Bus works)

33 kV, 6 kN Post Insulator (Isolators)

100Amp, Horn gap fuse

CT & PT JB complete with 30 nos Disconnecting type Terminal Blocks, complete with wiring.

Bay Marshalling Kiosk, made of 2.5 mm. thick sheet steel, protection class IP 55 complete with 200 TB.

Terminal connectors _ 33 kV side. The quantity of Terminal connectors shall be as per substation layout & shall b supplied as per technical specification as per individual equipment requirement

Terminal Connector for 36 kV Isolator to receive twin ACSR MOOSE Conductor

Terminal Connector for 36 kV Isolator to receive Single ACSR MOOSE Conductor

Terminal Connector for 36 kV SF6 Circuit Breaker to receive twin ACSR MOOSE Conductor

Terminal Connector for 36 kV SF6 Circuit Breaker to receive Single ACSR MOOSE Conductor

Terminal Connector for 36kV Current Transformer to receive twin ACSR MOOSE Conductor

Terminal Connector for 36kV Current Transformer to receive Single ACSR MOOSE Conductor

Terminal Connector for NCT suitable for 50x6 mm CU flat

Terminal Connector for 30 kV Lightning Arrester to receive Single ACSR MOOSE Conductor

Terminal Connector for 36 kV PT Connector to receive Single ACSR MOOSE Conductor

Transformer LV side Bushing Clamp (40/50 MVA Trafo)

Transformer MV side Bushing Clamp (250 kVA Trafo)

3 Inch IPS AL Tube for 33kV bus

Terminal connector for Bus PI suitable for 3 Inch IPS AL Tube

Terminal connector for Bus PI suitable for twin ACSR moose conductor

Terminal connector for Bus PI suitable for single ACSR moose conductor

Tee connector suitable for interconnection of twin ACSR moose conductor to Al tube.

Tee connector suitable for interconnection of Single ACSR moose conductor to Al tube.

Spacer for twin ACSR MOOSE with 250 mm sub conductor spacing, rigid

Terminal connector for Bus PI suitable for single ACSR moose conductor

End Caps and couplers/bends for 3Inch IPS AL Tube

Shield Wire Accessories

Lightning mast with spike (Tubular pole)

Control , Protection & Metering equipment

Control and Relay Panel

Indoor floor mounted, simplex type Control and Relay Panels, with mimic & annunciation panel for 132kV system as per specification comprising of the C & R Panels shall be complete with Numerical Relays and ABT Meters as per the Technical specifications & shall be compatible for SCADA/ SAS as open protocol.

132 kV Line Protection & control Panel

132/33 kV Transformer Protection & Control Panel

132 kV Bus Coupler Protection & Control Panel

Metering Panel for Lines

Indoor floor mounted, simplex type control and relay panels, with mimic & annunciation panel with ABT Meters for 33kV system as per specification and data sheet comprising of :

33KV Line Protection & Control Panel

33KV Transformer I/C Protection & Control Panel on 33 k V side of Power Transformer

33KV Protection & Control Panel for Bus Section The control, metering & protection system shall be complete with Numerical relays & compatible for performing the functions as per the electrical specifications & shall be fully compatible with substation automation /SCADA.

PLCC Equipment

EPAX(8x24) with 24 nos. telephone, cable etc

Digital Protection Coupler with PLC Terminal

LMU / LMDU

HF Cable 75 ohms(balanced)

132 kV, 800A wave trap for 40 kA for 1 sec. Wave trap will be CVT mounted.

Substation Automation

Substation Automation & SCADA system (as per the technical specification) along with Ethernet, Data Concentrator/ BCU , communication & data server, local work station with necessary accessories, hardware /software, fiber optic cabling & time synchronization equipment. Substation automation system of 132/33kV substations including hardware for present bays(132KV 8 Nos. bays , 33kV 10 no bays,) and software (for present bays and 132kV 3 no & 33kv 2 no future bays) along with associated equipment for each bay The system shall be complete with Numerical Relay compatible with substation automation for 132 kV & 33 kV system. The numerical relays along with other measuring / indicating Instruments shall be part of the integrated SCADA system. The complete system of this Substation shall be integrated on SCADA which shall be further the communicable to Master control center & further communicate to RLDC.

Earthing and Lightning protection material

65 x 12 mm MS flat for Main Earth mat & Auxiliary Mat

75 x 12 mm GI Flat for Equipment Earthing like CT,CB, Isolator , LA, BPI & Tower Earthing, riser below ground etc. (3.53kg/m)

75 x 12 GI Flat for earthing of Transformer body

50 x 6 mm GI Flat for earthing of Marshalling Boxes, Panel, Junction boxes, Distribution Board, Battery Charger etc. (2.36kg/m)

50x6 mm MS flat for cable trench earthing.

50 x 6 mm Copper flat for earthing of Transformer Neutral on HV as well LV Side. (2.69kg/m)

40 mm Dia, 6.5 mtr long GI rod earth electrode (perforated) for earthing of LA, CVT, Lightning Mast, Shield Wire Transformer Neutral

40 mm Dia 6.5 mtr long GI. Rod Earth Electrode at corners of Main Earth Mat , Gate & control room Earthing

Lightning spikes for building which 100 mm dia GI Pipe, 1.5 mtr to be mounted on insulated base on building top and connected with 50x6 mm GI Flat.

50x6 mm GI flat for all building spikes

40 mm Dia 6.5 mtr long GI. Rod Earth Electrode for building spikes earthing

Electrolytic grade copper plate 600mmx600mmx6mm for Transformer Neutral earthing to be provided in 6.5 mtr deep earth pit to be filled with salt & charcoal (as per standard earthing Practices)(Power trafor and aux. trafo)

Note: The quantity of GI Flat/MS rod for earthing & lightning protection is approximate. The exact quantity to be arranged as per GFC drawing and as per site requirement

Lattice type Structural Steel

Tower and Beams

Structural steel for Tower and beams (50% of MS and 50% of HT)

Hardwares, nuts, bolts and spring washer

Foundation Nuts and bolts

Equipment

Structural steel for Equipment

Hardwares, nuts, bolts and spring washer

Foundation Nuts and bolts for equipment

132 KV , Lightning cum lighting mast , 30 mtr high with lighting platform at 17 mtrs & 1.5 mtr spike at top

Hardware , Nuts & bolts for LM

Foundation Bolts

Cable and accessories

19/33 kV ( earthed system ) , 3Core 300 sqmm., AL Conductor, XLPE Insulated , PVC Sheathed, Armoured PVC Outer Sheath Cable for 33 kV outgoing feeder(200 meter/fedeer).

33 kV outdoor termination kit

LT Power Cable

AC Circuit 1.1 kV PVC Insulated 'PVC sheathed, GI wire / steel strip armoured, Aluminum/Copper Conductor cable of the following sizes:

Station transformer LV side to Main LVAC Board 3 1/2 core x 300 sq.mm AL (XLPE)cable from Station Transformer to LVAC Board

3 1/2 core x 150 Sqmm Al cable for oil filtration

3 1/2 core x 70 Sqmm Al cable for outdoor illumination & for battery charger

2 core x 16 Sqmm Cu cable for BMK, Trafo MB, fire panel & LDB

2 Core 6 Sqmm Cu cable for CT & CVT JB

4 Core 16 sqmm Al cable for panel illumination

4 Core 16 sqmm Al cable fo outdoor illumination JB

3 Core 2.5 sqmm CU cable fo outdoor illumination

DC Circuit

2 Core x 16 sqmm Cu cable for miscellaneous

2 Core x 50 sqmm Cu cable for DCDB to battery charger(Flexible multi strand)

1 C X 70 Sqmm Cu cable for Charger to battery (Flexible multi strand)

Termination with double compression Gland and Al lugs for 3 ½ core x 400 sqmm. Al cable.

Termination with double compression Gland and lugs 3 1/2 core x 150 sqmm. Al. cable

Termination with double compression Gland and lugs 2 core x 16 sqmm. Cu. Cable

Termination with double compression Gland and lugs 3 1/2 core x 150 sqmm. Al. cable

Termination with double compression Gland and lugs for 2core x 6 sqmm. Cu cable

Termination with double compression Gland and lugs for 4core x 16 sqmm.. Cable

Termination with double compression Gland and lugs for 2core x 16 sqmm.Cu cable

Termination with double compression Gland and lugs for 2core x 35 sqmm.. Cu cable

Termination with double compression Gland and lugs for1 core x 70 sqmm.. Crucible

Termination with double compression Gland and lugs for 3 corex 2.5 sqmm.Cu cable

Copper Control Cable

1100 V grade, PVC Insulated, PVC sheathed, steel round wire armoured, stranded control cables of the following sizes:

2 core 2.5 sqmm.

2 core 4 sqmm.

2 Core 6 sqmm.

4Core 4 sqmm.

4 core 2.5 sqmm.

7 core 2.5 sqmm.

12 core 2.5 sqmm.

19 Core 2.5 sqmm.

Double compression Glands and terminations (including ferruling, suitable Cu Lugs to meet the system requirements) for 1100 V grade PVC Insulated multicore Copper stranded conductor control cables of sizes: (2 core 2.5 sqmm.,2 core 4 sqmm., 2 Core 6 sqmm., 4Core 4 sqmm.,4Core 2.5 sqmm.7 core 2.5 sqmm,12 core 2.5 sqmm. &19 Core 2.5 sqmm.)

Cable Support & Cable Trays

Ladder type Cable Trays for outdoor

450 mm wide

300 mm wide

Perforated Cable Trays inside the Control Building

450 mm wide

300 mm wide

HDD/PVC pipe for laying cable from Trench to equipment

63 mm Dia

100 mm Dia

AC Distribution Board

AC 415V, 500A, 3-Ph cubicle type Indoor, floor mounted, auxiliary service board as per specification comprising of : (LVAC Board will have 2 sections , each section will be fed from independent Aux. transformer ( 250 KVA , 33/0.433 k V ).Busbar rating 600 A, 25 k A for 1 sec, Copper , IP 54 , 2 mm COLD ROLLED / 3 MM HOT ROLLED as aper specification )

DC Distribution Board ( 220 V DC & 48 VDC)

DC Distribution Board will have 2 sections , each section will be fed from independent Battery charger. Busbar rating 200 A FOR 220 V DC, 16 k A / FOR 1 SEC , AL or Copper , IP 54 , 2 mm COLD ROLLED / 3 MM HOT ROLLED) as per specification

DC Distribution Board will have 2 sections , each section will be fed from independent Battery charger. Busbar rating 200 A FOR 48 V DC, 16 k A / FOR 1 SEC , AL or Copper , IP 54 , 2 mm COLD ROLLED / 3 MM HOT ROLLED) as per specification

Battery and Battery charger

Battery set ( 220 V DC )

220V DC, 300 AH lead acid battery of VRLA type complete with accessories as per specification with 10% spare acid in non- returnable container (In tier arrangement).

Battery set ( 48 V DC )

48V DC, 200 AH lead acid battery of VRLA type complete with accessories as per specification with 10% spare acid in non- returnable container (In tier arrangement).

Battery charger ( 220 V DC )

Automatic float and Float cum boost charger 60 A suitable for 220 V 300 AH VRLA battery & charger shall be as per specification

Battery charger ( 48 V DC )

Automatic float and Float cum boost charger 50 A suitable for 48 V 200 AH VRLA battery & charger shall be as per specification

Fire fighting

NIFPS _ Nitrogen Injection Fire Fighting System System for Transformer

Fire Fighting equipment as per section-6 22.5 Kg capacity FE CO2 type, Trolley Mounted

25 Kg Capacity FE DCP type, Trolley Mounted

DCP 10 Kg Capacity, Wall mounted

FE CO2 6.5 Kg capacity, Wall mounted

DCP 5 Kg Capacity, Wall mounted

Foam Type 9 liter Capacity, Wall mounted

Water CO2 9 liter, Wall mounted

Fire Buckets (12 Nos. with stand in one set)

Outdoor illumination

LED flood light fitting with 250W led with all accessories control gear for Yard Lighting ( to be mounted on Gantry Tower )

LED flood light fitting with 250W led with all accessories control gear near boundary( to be mounted on 10 mtr. Pole)

LED street light fitting with 150W led with all accessories control gear on street ( to be mounted on 10 mtr. Pole)

70W LED lights post latern light mounted on 2.5 mtr. P-type pole

10 Mtr. MS Tubular poles 540SP-72

2.5 Mtr. P-type pole made of 100mm Dia GI Pipe

Lighting junction box for Light suitable for out door Installation comprising of 4 Nos. CBT M 4 type terminal connector for light connections Max size 150 x150x100mm

Air conditioning

Split unit for Control room (capacity 2 TR)

Measuring Instruments

Digital earth resistance meter

5 kV automated Insulation resistance meter

Earthing stick

Furniture

Executive Table :(1800mmX900mm)(Wooden)

Executive Chair:(Revolving mid back type)

Visitor's Chair with hand rest

Computer Room Executive Chair (Revolving mid back type)

2 nos. of Steel Almirah LengthXWidthXHeight in mm(1016X560X1980)

1 Nos. of Recta work station of size 1200mmX600mm,25 mm thick work top with 3 drawer pedestal along with keyboard tray and CPU trolley and partitions of thickness 53 mm and of height 1200 mm.

Miscelleaneous items (First Aid box -2 nos ,Accident prevention chart - 2nos, Aluminum alloy ladder - 2 nos , Safety belt 6nos , Earthing stick -3 nos , Helmet - 10 nos))

Description of Work / Item(s)

Amount

Power transformer

40/50 MVA, 132/33 kV, 3-Ph, YNyn0, Z =10 %, ONAN/ONAF with copper wound Power Transformer with OLTC(+5% to -15% in steps of 1.25%) , RTCC panel including all cabling & 10% spare oil.The Transformer shall be suitable for single / twin ACSR MOOSE Conductor termination on HV and twin ACSR MOOSE conductor on LV side. The transformer will be supplied with Bushing mounted NCT on HV & LV side as per the CT ration given in the SLD.The Transformer shall be suitable for outdoor installation & complete with all accessories to meet the technical specification.

250 kVA, 33/0.433 kV, Copper Wound, 3ph, Dyn-11, Z=4% outdoor type "Station Transformer" with OFF Circuit Tap Changer , -5% to + 5 % in steps for 2.5 % & including 10 % spare oil.MV connection shall be through single ACSR MOOSE Conductor, LV Side shall be connected through XLPE Insulated LT cable.

132kV Equipment

145 kV, 3150 A, SCR 40 kA for 1 sec, SF6 Circuit Breaker, outdoor type, 3-Ph gang operated complete with operating mechanism & support structure with 10 % spare SF-6 gas.

145 KV, 1250 A, 40 kA for 1 sec, 3-Ph gang operated Double Break Centre Post rotating , outdoor type , motor operated Disconnector (Isolator) complete without solid core post Insulator.

Without earth switch

With one earth switch(manual)

With Two earth switch(manual)

With one earth switch(manual) Tandem type

145 KV Outdoor type, live tank, single phase Current Transformer as per the details below: The CT shall meet the technical specification & other design requirement as per design requirement.

Transformer feeder CTR : 600-300/1-1-1-1 A

Line & Bus Coupler CTR: 600-300/1-1-1-1 A

145 kV, 1-ph, Capacitor Voltage Transformer (CVT) for 132 kV Incoming Line (132kV/√3/110/√3/110/√3V/110/√3V) as per technical specification.

145 kV, 1-ph, Potential Transformer (PT) on BUS (132kV/√3/110/√3/110/√3V110/√3V) as per the technical specification.

120 kV, 10 kA, Metal Oxide type, heavy duty, station class 3, Lightning Arrestor complete with Surge Counter & flexible copper connecting lead.

145kV BPI for Buswork

145kV BPI for Isolators

CT, CVT & PT JB complete with 30 nos Disconnecting type Terminals Blocks, complete with wiring.

Bay Marshalling Kiosk, made of 2.5 mm. thick sheet steel, protection class IP 55 complete with 250 TB

String Insulator Hardware for 132 kV

Single Tension Insulator assembly suitable for 11 kV, 90 kN Disc Insulator with all hardwares accessories for twin ACSR MOOSE conductor ( without disc Insulator) with turn buckle.

Single Tension Insulator assembly suitable for 11 KV, 90 kN Disc Insulator with all hardwares accessories for twin ACSR MOOSE conductor ( without disc Insulator) without turn buckle.

Single Suspension Insulator assembly suitable for 11 KV, 70 kN Disc Insulator with all hardwares accessories for twin ACSR MOOSE conductor for through type ( without disc Insulator)

Single Suspension Insulator assembly suitable for 11 KV, 70 kN Disc Insulator with all hardwares accessories for single ACSR MOOSE conductor for through type ( without disc Insulator).

Single Suspension Insulator assembly suitable for 11 KV, 70 kN Disc Insulator with all hardwares accessories for single ACSR MOOSE conductor for Drop type ( without disc Insulator).

Single Tension Insulator assembly suitable for 11 KV, 90 kN Disc Insulator with all hardwares accessories for single ACSR MOOSE conductor ( without disc Insulator) with turn buckle.

Single Tension Insulator assembly suitable for 11 KV, 90 kN Disc Insulator with all hardwares accessories for single ACSR MOOSE conductor ( without disc Insulator ) without turn buckle.

Single Suspension Insulator assembly suitable for 11 KV, 70 kN Disc Insulator with all hardwares accessories for Twin ACSR MOOSE conductor for Drop type

90 KN Disc Insulator , B & S type for the String Insulator (Tension) with 5% spare

70 KN Disc Insulator (Suspension) with 5% spare

ACSR MOOSE conductor

Terminal connectors for 132kV side. The Quantity of Terminal connectors shall be as per substation layout & shall be supplied as per technical specification as per individual equipment requirement

Terminal connector for 145kV Isolator to receive single ACSR MOOSE Conductor.

Terminal connector for 145kV SF6 Circuit Breaker to receive single ACSR MOOSE Conductor

Terminal connector for 145kV Current Transformer terminal to receive single ACSR MOOSE Conductor

Terminal connector for 145kV CVT terminal to receive Single ACSR MOOSE Conductor

Terminal connector for 145kV PT terminal to receive Single ACSR MOOSE Conductor

Terminal connector for 145kV BPI to receive single ACSR MOOSE Conductor

Terminal connector for Wave-trap to receive single ACSR MOOSE Conductor

Terminal connector for 120kV Lightning Arrester to receive Single ACSR MOOSE Conductor

Transformer Bushing Connector ( 145kV Side )

Terminal connector for NCT suitable for 50x6 mm CU flat

Spacer for twin ACSR MOOSE with 250mm sub conductor spacing, rigid

C-Wedge connector for twin ACSR MOOSE

C-Wedge connector for single ACSR MOOSE

T- type connector suitable for single ACSR MOOSE through and same T-off

Shield Wire & Accessories

7/3.15 mm GSS wire for shielding

Tension Fittings for 7/3.15mm Earth wire

Earth Wire Connector (PG Clamps)

Cleat Clamp for clamping 7/3.15 mm GSS wire on to the Structure

Pad Clamp for clamping 7/3.15 mm GSS wire on to the Structure for earthing

33 kV Equipment The equipment shall be suitable for outdoor installation and shall meet the technical requirement as per specification for 33 kV , 50 Hz, 31. kA/3 Sec., Creepage as 25 mm / Kv

36 kV, 1250 A, SCR 31.5/3sec, SF6, Outdoor type, 3-Ph gang operated complete with operating mechanism & support structure for Incoming Feeders & Bus coupler.

36 kV, 1250 A, SCR 31.5/ 3 sec , SF6, Outdoor type, 3-Ph gang operated complete with operating mechanism & support structure for Outgoing Feeders.

36 KV,1250 A, 3-Ph gang operated, Outdoor type, Double Break centre Post rotating outdoor type motor operated Disconnector (Isolator) without solid core Post Insulator.

Without earth switch for Incomer from Transformer

With one earth switch for Bus Coupler

Outdoor type 36 kV, 630 A, 3-Ph gang operated, outdoor type, Double Break centre Post rotating outdoor type motor operated Disconnector (Isolator) with solid core Post Insulator.

With one earth switch

Without earth switch

36 kV Out door type, live tank, single phase Current Transformers as given below:The CT shall meet the technical specification & other design requirements.

36 kV Transformer side & Bus Coupler CTR:1200-600 /1-1-1 A

36 kV outgoing Line Feeder CTR:1200-600/1-1-1 A

15 kV Neutral Current Transformer for 132/33 kV transformer on 33 kV side, CTR1200-600/1 -1A

Outdoor type 36 kV ,1-ph, Potential Transformer(PT) (33kV/√3/110/√3/110/√3V) as per technical specification

30 kV,10 kA, Metal Oxide type, heavy duty, station class Lightning Arrestor complete with Surge Counter & copper connecting lead

33 kV, 8 kN Post Insulator (Bus works)

33 kV, 6 kN Post Insulator (Isolators)

100Amp, Horn gap fuse

CT & PT JB complete with 30 nos Disconnecting type Terminal Blocks, complete with wiring.

Bay Marshalling Kiosk, made of 2.5 mm. thick sheet steel, protection class IP 55 complete with 200 TB.

Terminal connectors _ 33 kV side. The quantity of Terminal connectors shall be as per substation layout & shall b supplied as per technical specification as per individual equipment requirement

Terminal Connector for 36 kV Isolator to receive twin ACSR MOOSE Conductor

Terminal Connector for 36 kV Isolator to receive Single ACSR MOOSE Conductor

Terminal Connector for 36 kV SF6 Circuit Breaker to receive twin ACSR MOOSE Conductor

Terminal Connector for 36 kV SF6 Circuit Breaker to receive Single ACSR MOOSE Conductor

Terminal Connector for 36kV Current Transformer to receive twin ACSR MOOSE Conductor

Terminal Connector for 36kV Current Transformer to receive Single ACSR MOOSE Conductor

Terminal Connector for NCT suitable for 50x6 mm CU flat

Terminal Connector for 30 kV Lightning Arrester to receive Single ACSR MOOSE Conductor

Terminal Connector for 36 kV PT Connector to receive Single ACSR MOOSE Conductor

Transformer LV side Bushing Clamp (40/50 MVA Trafo)

Transformer MV side Bushing Clamp (250 kVA Trafo)

3 Inch IPS AL Tube for 33kV bus

Terminal connector for Bus PI suitable for 3 Inch IPS AL Tube

Terminal connector for Bus PI suitable for twin ACSR moose conductor

Terminal connector for Bus PI suitable for single ACSR moose conductor

Tee connector suitable for interconnection of twin ACSR moose conductor to Al tube.

Tee connector suitable for interconnection of Single ACSR moose conductor to Al tube.

Spacer for twin ACSR MOOSE with 250 mm sub conductor spacing, rigid

Terminal connector for Bus PI suitable for single ACSR moose conductor

End Caps and couplers/bends for 3Inch IPS AL Tube

Shield Wire Accessories

Lightning mast with spike (Tubular pole)

Control , Protection & Metering equipment

Control and Relay Panel

Indoor floor mounted, simplex type Control and Relay Panels, with mimic & annunciation panel for 132kV system as per specification comprising of the C & R Panels shall be complete with Numerical Relays and ABT Meters as per the Technical specifications & shall be compatible for SCADA/ SAS as open protocol.

132 kV Line Protection & control Panel

132/33 kV Transformer Protection & Control Panel

132 kV Bus Coupler Protection & Control Panel

Metering Panel for Lines

Indoor floor mounted, simplex type control and relay panels, with mimic & annunciation panel with ABT Meters for 33kV system as per specification and data sheet comprising of :

33KV Line Protection & Control Panel

33KV Transformer I/C Protection & Control Panel on 33 k V side of Power Transformer

33KV Protection & Control Panel for Bus Section The control, metering & protection system shall be complete with Numerical relays & compatible for performing the functions as per the electrical specifications & shall be fully compatible with substation automation /SCADA.

PLCC Equipment

EPAX(8x24) with 24 nos. telephone, cable etc

Digital Protection Coupler with PLC Terminal

LMU / LMDU

HF Cable 75 ohms(balanced)

132 kV, 800A wave trap for 40 kA for 1 sec. Wave trap will be CVT mounted.

Substation Automation

Substation Automation & SCADA system (as per the technical specification) along with Ethernet, Data Concentrator/ BCU , communication & data server, local work station with necessary accessories, hardware /software, fiber optic cabling & time synchronization equipment. Substation automation system of 132/33kV substations including hardware for present bays(132KV 8 Nos. bays , 33kV 10 no bays,) and software (for present bays and 132kV 3 no & 33kv 2 no future bays) along with associated equipment for each bay The system shall be complete with Numerical Relay compatible with substation automation for 132 kV & 33 kV system. The numerical relays along with other measuring / indicating Instruments shall be part of the integrated SCADA system. The complete system of this Substation shall be integrated on SCADA which shall be further the communicable to Master control center & further communicate to RLDC.

Earthing and Lightning protection material

65 x 12 mm MS flat for Main Earth mat & Auxiliary Mat

75 x 12 mm GI Flat for Equipment Earthing like CT,CB, Isolator , LA, BPI & Tower Earthing, riser below ground etc. (3.53kg/m)

75 x 12 GI Flat for earthing of Transformer body

50 x 6 mm GI Flat for earthing of Marshalling Boxes, Panel, Junction boxes, Distribution Board, Battery Charger etc. (2.36kg/m)

50x6 mm MS flat for cable trench earthing.

50 x 6 mm Copper flat for earthing of Transformer Neutral on HV as well LV Side. (2.69kg/m)

40 mm Dia, 6.5 mtr long GI rod earth electrode (perforated) for earthing of LA, CVT, Lightning Mast, Shield Wire Transformer Neutral

40 mm Dia 6.5 mtr long GI. Rod Earth Electrode at corners of Main Earth Mat , Gate & control room Earthing

Lightning spikes for building which 100 mm dia GI Pipe, 1.5 mtr to be mounted on insulated base on building top and connected with 50x6 mm GI Flat.

50x6 mm GI flat for all building spikes

40 mm Dia 6.5 mtr long GI. Rod Earth Electrode for building spikes earthing

Electrolytic grade copper plate 600mmx600mmx6mm for Transformer Neutral earthing to be provided in 6.5 mtr deep earth pit to be filled with salt & charcoal (as per standard earthing Practices)(Power trafor and aux. trafo)

Note: The quantity of GI Flat/MS rod for earthing & lightning protection is approximate. The exact quantity to be arranged as per GFC drawing and as per site requirement

Lattice type Structural Steel

Tower and Beams

Structural steel for Tower and beams (50% of MS and 50% of HT)

Hardwares, nuts, bolts and spring washer

Foundation Nuts and bolts

Equipment

Structural steel for Equipment

Hardwares, nuts, bolts and spring washer

Foundation Nuts and bolts for equipment

132 KV , Lightning cum lighting mast , 30 mtr high with lighting platform at 17 mtrs & 1.5 mtr spike at top

Hardware , Nuts & bolts for LM

Foundation Bolts

Cable and accessories

19/33 kV ( earthed system ) , 3Core 300 sqmm., AL Conductor, XLPE Insulated , PVC Sheathed, Armoured PVC Outer Sheath Cable for 33 kV outgoing feeder(200 meter/fedeer).

33 kV outdoor termination kit

LT Power Cable

AC Circuit 1.1 kV PVC Insulated 'PVC sheathed, GI wire / steel strip armoured, Aluminum/Copper Conductor cable of the following sizes:

Station transformer LV side to Main LVAC Board 3 1/2 core x 300 sq.mm AL (XLPE)cable from Station Transformer to LVAC Board

3 1/2 core x 150 Sqmm Al cable for oil filtration

3 1/2 core x 70 Sqmm Al cable for outdoor illumination & for battery charger

2 core x 16 Sqmm Cu cable for BMK, Trafo MB, fire panel & LDB

2 Core 6 Sqmm Cu cable for CT & CVT JB

4 Core 16 sqmm Al cable for panel illumination

4 Core 16 sqmm Al cable fo outdoor illumination JB

3 Core 2.5 sqmm CU cable fo outdoor illumination

DC Circuit

2 Core x 16 sqmm Cu cable for miscellaneous

2 Core x 50 sqmm Cu cable for DCDB to battery charger(Flexible multi strand)

1 C X 70 Sqmm Cu cable for Charger to battery (Flexible multi strand)

Termination with double compression Gland and Al lugs for 3 ½ core x 400 sqmm. Al cable.

Termination with double compression Gland and lugs 3 1/2 core x 150 sqmm. Al. cable

Termination with double compression Gland and lugs 2 core x 16 sqmm. Cu. Cable

Termination with double compression Gland and lugs 3 1/2 core x 150 sqmm. Al. cable

Termination with double compression Gland and lugs for 2core x 6 sqmm. Cu cable

Termination with double compression Gland and lugs for 4core x 16 sqmm.. Cable

Termination with double compression Gland and lugs for 2core x 16 sqmm.Cu cable

Termination with double compression Gland and lugs for 2core x 35 sqmm.. Cu cable

Termination with double compression Gland and lugs for1 core x 70 sqmm.. Crucible

Termination with double compression Gland and lugs for 3 corex 2.5 sqmm.Cu cable

Copper Control Cable

1100 V grade, PVC Insulated, PVC sheathed, steel round wire armoured, stranded control cables of the following sizes:

2 core 2.5 sqmm.

2 core 4 sqmm.

2 Core 6 sqmm.

4Core 4 sqmm.

4 core 2.5 sqmm.

7 core 2.5 sqmm.

12 core 2.5 sqmm.

19 Core 2.5 sqmm.

Double compression Glands and terminations (including ferruling, suitable Cu Lugs to meet the system requirements) for 1100 V grade PVC Insulated multicore Copper stranded conductor control cables of sizes: (2 core 2.5 sqmm.,2 core 4 sqmm., 2 Core 6 sqmm., 4Core 4 sqmm.,4Core 2.5 sqmm.7 core 2.5 sqmm,12 core 2.5 sqmm. &19 Core 2.5 sqmm.)

Cable Support & Cable Trays

Ladder type Cable Trays for outdoor

450 mm wide

300 mm wide

Perforated Cable Trays inside the Control Building

450 mm wide

300 mm wide

HDD/PVC pipe for laying cable from Trench to equipment

63 mm Dia

100 mm Dia

AC Distribution Board

AC 415V, 500A, 3-Ph cubicle type Indoor, floor mounted, auxiliary service board as per specification comprising of : (LVAC Board will have 2 sections , each section will be fed from independent Aux. transformer ( 250 KVA , 33/0.433 k V ).Busbar rating 600 A, 25 k A for 1 sec, Copper , IP 54 , 2 mm COLD ROLLED / 3 MM HOT ROLLED as aper specification )

DC Distribution Board ( 220 V DC & 48 VDC)

DC Distribution Board will have 2 sections , each section will be fed from independent Battery charger. Busbar rating 200 A FOR 220 V DC, 16 k A / FOR 1 SEC , AL or Copper , IP 54 , 2 mm COLD ROLLED / 3 MM HOT ROLLED) as per specification

DC Distribution Board will have 2 sections , each section will be fed from independent Battery charger. Busbar rating 200 A FOR 48 V DC, 16 k A / FOR 1 SEC , AL or Copper , IP 54 , 2 mm COLD ROLLED / 3 MM HOT ROLLED) as per specification

Battery and Battery charger

Battery set ( 220 V DC )

220V DC, 300 AH lead acid battery of VRLA type complete with accessories as per specification with 10% spare acid in non- returnable container (In tier arrangement).

Battery set ( 48 V DC )

48V DC, 200 AH lead acid battery of VRLA type complete with accessories as per specification with 10% spare acid in non- returnable container (In tier arrangement).

Battery charger ( 220 V DC )

Automatic float and Float cum boost charger 60 A suitable for 220 V 300 AH VRLA battery & charger shall be as per specification

Battery charger ( 48 V DC )

Automatic float and Float cum boost charger 50 A suitable for 48 V 200 AH VRLA battery & charger shall be as per specification

Fire fighting

NIFPS _ Nitrogen Injection Fire Fighting System System for Transformer

Fire Fighting equipment as per section-6 22.5 Kg capacity FE CO2 type, Trolley Mounted

25 Kg Capacity FE DCP type, Trolley Mounted

DCP 10 Kg Capacity, Wall mounted

FE CO2 6.5 Kg capacity, Wall mounted

DCP 5 Kg Capacity, Wall mounted

Foam Type 9 liter Capacity, Wall mounted

Water CO2 9 liter, Wall mounted

Fire Buckets (12 Nos. with stand in one set)

Outdoor illumination

LED flood light fitting with 250W led with all accessories control gear for Yard Lighting ( to be mounted on Gantry Tower )

LED flood light fitting with 250W led with all accessories control gear near boundary( to be mounted on 10 mtr. Pole)

LED street light fitting with 150W led with all accessories control gear on street ( to be mounted on 10 mtr. Pole)

70W LED lights post latern light mounted on 2.5 mtr. P-type pole

10 Mtr. MS Tubular poles 540SP-72

2.5 Mtr. P-type pole made of 100mm Dia GI Pipe

Lighting junction box for Light suitable for out door Installation comprising of 4 Nos. CBT M 4 type terminal connector for light connections Max size 150 x150x100mm

Air conditioning

Split unit for Control room (capacity 2 TR)

Measuring Instruments

Digital earth resistance meter

5 kV automated Insulation resistance meter

Earthing stick

Furniture

Executive Table :(1800mmX900mm)(Wooden)

Executive Chair:(Revolving mid back type)

Visitor's Chair with hand rest

Computer Room Executive Chair (Revolving mid back type)

2 nos. of Steel Almirah LengthXWidthXHeight in mm(1016X560X1980)

1 Nos. of Recta work station of size 1200mmX600mm,25 mm thick work top with 3 drawer pedestal along with keyboard tray and CPU trolley and partitions of thickness 53 mm and of height 1200 mm.

Miscelleaneous items (First Aid box -2 nos ,Accident prevention chart - 2nos, Aluminum alloy ladder - 2 nos , Safety belt 6nos , Earthing stick -3 nos , Helmet - 10 nos))

Description of Work / Item(s)

Amount

ETC of Power transformer

40/50 MVA, 132/33 kV, 3-Ph, YNyn0, Z =10 %, ONAN/ONAF with copper wound Power Transformer with OLTC(+5% to -15% in steps of 1.25%) , RTCC panel including all cabling & 10% spare oil.The Transformer shall be suitable for single / twin ACSR MOOSE Conductor termination on HV and twin ACSR MOOSE conductor on LV side. The transformer will be supplied with Bushing mounted NCT on HV & LV side as per the CT ration given in the SLD.The Transformer shall be suitable for outdoor installation & complete with all accessories to meet the technical specification.

250 kVA, 33/0.433 kV, Copper Wound, 3ph, Dyn-11, Z=4% outdoor type "Station Transformer" with OFF Circuit Tap Changer , -5% to + 5 % in steps for 2.5 % & including 10 % spare oil.MV connection shall be through single ACSR MOOSE Conductor, LV Side shall be connected through XLPE Insulated LT cable.

ETC of 132kV Equipment

145 kV, 3150 A, SCR 40 kA for 1 sec, SF6 Circuit Breaker, outdoor type, 3-Ph gang operated complete with operating mechanism & support structure with 10 % spare SF-6 gas.

145 KV, 1250 A, 40 kA for 1 sec, 3-Ph gang operated Double Break Centre Post rotating , outdoor type , motor operated Disconnector (Isolator) complete without solid core post Insulator.

Without earth switch

With one earth switch(manual)

With Two earth switch(manual)

With one earth switch(manual) Tandem type

145 KV Outdoor type, live tank, single phase Current Transformer as per the details below: The CT shall meet the technical specification & other design requirement as per design requirement.

Transformer feeder CTR : 600-300/1-1-1-1 A

Line & Bus Coupler CTR: 600-300/1-1-1-1 A

145 kV, 1-ph, Capacitor Voltage Transformer (CVT) for 132 kV Incoming Line (132kV/√3/110/√3/110/√3V/110/√3V) as per technical specification.

145 kV, 1-ph, Potential Transformer (PT) on BUS (132kV/√3/110/√3/110/√3V110/√3V) as per the technical specification.

120 kV, 10 kA, Metal Oxide type, heavy duty, station class 3, Lightning Arrestor complete with Surge Counter & flexible copper connecting lead.

145kV BPI for Buswork

145kV BPI for Isolators

CT, CVT & PT JB complete with 30 nos Disconnecting type Terminals Blocks, complete with wiring.

Bay Marshalling Kiosk, made of 2.5 mm. thick sheet steel, protection class IP 55 complete with 250 TB

ETC of String Insulator Hardware for 132 kV

Single Tension Insulator assembly suitable for 11 kV, 90 kN Disc Insulator with all hardwares accessories for twin ACSR MOOSE conductor ( without disc Insulator) with turn buckle.

Single Tension Insulator assembly suitable for 11 KV, 90 kN Disc Insulator with all hardwares accessories for twin ACSR MOOSE conductor ( without disc Insulator) without turn buckle.

Single Suspension Insulator assembly suitable for 11 KV, 70 kN Disc Insulator with all hardwares accessories for twin ACSR MOOSE conductor for through type ( without disc Insulator)

Single Suspension Insulator assembly suitable for 11 KV, 70 kN Disc Insulator with all hardwares accessories for single ACSR MOOSE conductor for through type ( without disc Insulator).

Single Suspension Insulator assembly suitable for 11 KV, 70 kN Disc Insulator with all hardwares accessories for single ACSR MOOSE conductor for Drop type ( without disc Insulator).

Single Tension Insulator assembly suitable for 11 KV, 90 kN Disc Insulator with all hardwares accessories for single ACSR MOOSE conductor ( without disc Insulator) with turn buckle.

Single Tension Insulator assembly suitable for 11 KV, 90 kN Disc Insulator with all hardwares accessories for single ACSR MOOSE conductor ( without disc Insulator ) without turn buckle.

Single Suspension Insulator assembly suitable for 11 KV, 70 kN Disc Insulator with all hardwares accessories for Twin ACSR MOOSE conductor for Drop type

90 KN Disc Insulator , B & S type for the String Insulator (Tension) with 5% spare

70 KN Disc Insulator (Suspension) with 5% spare

ACSR MOOSE conductor

ETC of Terminal connectors for 132kV side. The Quantity of Terminal connectors shall be as per substation layout & shall be supplied as per technical specification as per individual equipment requirement

Terminal connector for 145kV Isolator to receive single ACSR MOOSE Conductor.

Terminal connector for 145kV SF6 Circuit Breaker to receive single ACSR MOOSE Conductor

Terminal connector for 145kV Current Transformer terminal to receive single ACSR MOOSE Conductor

Terminal connector for 145kV CVT terminal to receive Single ACSR MOOSE Conductor

Terminal connector for 145kV PT terminal to receive Single ACSR MOOSE Conductor

Terminal connector for 145kV BPI to receive single ACSR MOOSE Conductor

Terminal connector for Wave-trap to receive single ACSR MOOSE Conductor

Terminal connector for 120kV Lightning Arrester to receive Single ACSR MOOSE Conductor

Transformer Bushing Connector ( 145kV Side )

Terminal connector for NCT suitable for 50x6 mm CU flat

Spacer for twin ACSR MOOSE with 250mm sub conductor spacing, rigid

C-Wedge connector for twin ACSR MOOSE

C-Wedge connector for single ACSR MOOSE

T- type connector suitable for single ACSR MOOSE through and same T-off

ETC of Shield Wire & Accessories

7/3.15 mm GSS wire for shielding

Tension Fittings for 7/3.15mm Earth wire

Earth Wire Connector (PG Clamps)

Cleat Clamp for clamping 7/3.15 mm GSS wire on to the Structure

Pad Clamp for clamping 7/3.15 mm GSS wire on to the Structure for earthing

ETC of 33 kV Equipment The equipment shall be suitable for outdoor installation and shall meet the technical requirement as per specification for 33 kV , 50 Hz, 31. kA/3 Sec., Creepage as 25 mm / Kv

36 kV, 1250 A, SCR 31.5/3sec, SF6, Outdoor type, 3-Ph gang operated complete with operating mechanism & support structure for Incoming Feeders & Bus coupler.

36 kV, 1250 A, SCR 31.5/ 3 sec , SF6, Outdoor type, 3-Ph gang operated complete with operating mechanism & support structure for Outgoing Feeders.

36 KV,1250 A, 3-Ph gang operated, Outdoor type, Double Break centre Post rotating outdoor type motor operated Disconnector (Isolator) without solid core Post Insulator.

Without earth switch for Incomer from Transformer

With one earth switch for Bus Coupler

Outdoor type 36 kV, 630 A, 3-Ph gang operated, outdoor type, Double Break centre Post rotating outdoor type motor operated Disconnector (Isolator) with solid core Post Insulator.

With one earth switch

Without earth switch

36 kV Out door type, live tank, single phase Current Transformers as given below:The CT shall meet the technical specification & other design requirements.

36 kV Transformer side & Bus Coupler CTR:1200-600 /1-1-1 A

36 kV outgoing Line Feeder CTR:1200-600/1-1-1 A

15 kV Neutral Current Transformer for 132/33 kV transformer on 33 kV side, CTR1200-600/1 -1A

Outdoor type 36 kV ,1-ph, Potential Transformer(PT) (33kV/√3/110/√3/110/√3V) as per technical specification

30 kV,10 kA, Metal Oxide type, heavy duty, station class Lightning Arrestor complete with Surge Counter & copper connecting lead

33 kV, 8 kN Post Insulator (Bus works)

33 kV, 6 kN Post Insulator (Isolators)

100Amp, Horn gap fuse

CT & PT JB complete with 30 nos Disconnecting type Terminal Blocks, complete with wiring.

Bay Marshalling Kiosk, made of 2.5 mm. thick sheet steel, protection class IP 55 complete with 200 TB.

ETC of Terminal connectors _ 33 kV side. The quantity of Terminal connectors shall be as per substation layout & shall b supplied as per technical specification as per individual equipment requirement

Terminal Connector for 36 kV Isolator to receive twin ACSR MOOSE Conductor

Terminal Connector for 36 kV Isolator to receive Single ACSR MOOSE Conductor

Terminal Connector for 36 kV SF6 Circuit Breaker to receive twin ACSR MOOSE Conductor

Terminal Connector for 36 kV SF6 Circuit Breaker to receive Single ACSR MOOSE Conductor

Terminal Connector for 36kV Current Transformer to receive twin ACSR MOOSE Conductor

Terminal Connector for 36kV Current Transformer to receive Single ACSR MOOSE Conductor

Terminal Connector for NCT suitable for 50x6 mm CU flat

Terminal Connector for 30 kV Lightning Arrester to receive Single ACSR MOOSE Conductor

Terminal Connector for 36 kV PT Connector to receive Single ACSR MOOSE Conductor

Transformer LV side Bushing Clamp (40/50 MVA Trafo)

Transformer MV side Bushing Clamp (250 kVA Trafo)

3 Inch IPS AL Tube for 33kV bus

Terminal connector for Bus PI suitable for 3 Inch IPS AL Tube

Terminal connector for Bus PI suitable for twin ACSR moose conductor

Terminal connector for Bus PI suitable for single ACSR moose conductor

Tee connector suitable for interconnection of twin ACSR moose conductor to Al tube.

Tee connector suitable for interconnection of Single ACSR moose conductor to Al tube.

Spacer for twin ACSR MOOSE with 250 mm sub conductor spacing, rigid

Terminal connector for Bus PI suitable for single ACSR moose conductor

End Caps and couplers/bends for 3Inch IPS AL Tube

ETC of Shield Wire Accessories

Lightning mast with spike (Tubular pole)

ETC of Control , Protection & Metering equipment

Control and Relay Panel

Indoor floor mounted, simplex type Control and Relay Panels, with mimic & annunciation panel for 132kV system as per specification comprising of the C & R Panels shall be complete with Numerical Relays and ABT Meters as per the Technical specifications & shall be compatible for SCADA/ SAS as open protocol.

132 kV Line Protection & control Panel

132/33 kV Transformer Protection & Control Panel

132 kV Bus Coupler Protection & Control Panel

Metering Panel for Lines

Indoor floor mounted, simplex type control and relay panels, with mimic & annunciation panel with ABT Meters for 33kV system as per specification and data sheet comprising of :

33KV Line Protection & Control Panel

33KV Transformer I/C Protection & Control Panel on 33 k V side of Power Transformer

33KV Protection & Control Panel for Bus Section The control, metering & protection system shall be complete with Numerical relays & compatible for performing the functions as per the electrical specifications & shall be fully compatible with substation automation /SCADA.

ETC of PLCC Equipment

EPAX(8x24) with 24 nos. telephone, cable etc

Digital Protection Coupler with PLC Terminal

LMU / LMDU

HF Cable 75 ohms(balanced)

132 kV, 800A wave trap for 40 kA for 1 sec. Wave trap will be CVT mounted.

ETC of Substation Automation

Substation Automation & SCADA system (as per the technical specification) along with Ethernet, Data Concentrator/ BCU , communication & data server, local work station with necessary accessories, hardware /software, fiber optic cabling & time synchronization equipment. Substation automation system of 132/33kV substations including hardware for present bays(132KV 8 Nos. bays , 33kV 10 no bays,) and software (for present bays and 132kV 3 no & 33kv 2 no future bays) along with associated equipment for each bay The system shall be complete with Numerical Relay compatible with substation automation for 132 kV & 33 kV system. The numerical relays along with other measuring / indicating Instruments shall be part of the integrated SCADA system. The complete system of this Substation shall be integrated on SCADA which shall be further the communicable to Master control center & further communicate to RLDC.

ETC of Earthing and Lightning protection material

65 x 12 mm MS flat for Main Earth mat & Auxiliary Mat

75 x 12 mm GI Flat for Equipment Earthing like CT,CB, Isolator , LA, BPI & Tower Earthing, riser below ground etc. (3.53kg/m)

75 x 12 GI Flat for earthing of Transformer body

50 x 6 mm GI Flat for earthing of Marshalling Boxes, Panel, Junction boxes, Distribution Board, Battery Charger etc. (2.36kg/m)

50x6 mm MS flat for cable trench earthing.

50 x 6 mm Copper flat for earthing of Transformer Neutral on HV as well LV Side. (2.69kg/m)

40 mm Dia, 6.5 mtr long GI rod earth electrode (perforated) for earthing of LA, CVT, Lightning Mast, Shield Wire Transformer Neutral

40 mm Dia 6.5 mtr long GI. Rod Earth Electrode at corners of Main Earth Mat , Gate & control room Earthing

Lightning spikes for building which 100 mm dia GI Pipe, 1.5 mtr to be mounted on insulated base on building top and connected with 50x6 mm GI Flat.

50x6 mm GI flat for all building spikes

40 mm Dia 6.5 mtr long GI. Rod Earth Electrode for building spikes earthing

Electrolytic grade copper plate 600mmx600mmx6mm for Transformer Neutral earthing to be provided in 6.5 mtr deep earth pit to be filled with salt & charcoal (as per standard earthing Practices)(Power trafor and aux. trafo)

Note: The quantity of GI Flat/MS rod for earthing & lightning protection is approximate. The exact quantity to be arranged as per GFC drawing and as per site requirement

ETC of Lattice type Structural Steel

Tower and Beams

Structural steel for Tower and beams (50% of MS and 50% of HT)

Hardwares, nuts, bolts and spring washer

Foundation Nuts and bolts

Equipment

Structural steel for Equipment

Hardwares, nuts, bolts and spring washer

Foundation Nuts and bolts for equipment

132 KV , Lightning cum lighting mast , 30 mtr high with lighting platform at 17 mtrs & 1.5 mtr spike at top

Hardware , Nuts & bolts for LM

Foundation Bolts

Cable and accessories

19/33 kV ( earthed system ) , 3Core 300 sqmm., AL Conductor, XLPE Insulated , PVC Sheathed, Armoured PVC Outer Sheath Cable for 33 kV outgoing feeder(200 meter/fedeer).

33 kV outdoor termination kit

ETC of LT Power Cable

AC Circuit 1.1 kV PVC Insulated 'PVC sheathed, GI wire / steel strip armoured, Aluminum/Copper Conductor cable of the following sizes:

Station transformer LV side to Main LVAC Board 3 1/2 core x 300 sq.mm AL (XLPE)cable from Station Transformer to LVAC Board

3 1/2 core x 150 Sqmm Al cable for oil filtration

3 1/2 core x 70 Sqmm Al cable for outdoor illumination & for battery charger

2 core x 16 Sqmm Cu cable for BMK, Trafo MB, fire panel & LDB

2 Core 6 Sqmm Cu cable for CT & CVT JB

4 Core 16 sqmm Al cable for panel illumination

4 Core 16 sqmm Al cable fo outdoor illumination JB

3 Core 2.5 sqmm CU cable fo outdoor illumination

DC Circuit

2 Core x 16 sqmm Cu cable for miscellaneous

2 Core x 50 sqmm Cu cable for DCDB to battery charger(Flexible multi strand)

1 C X 70 Sqmm Cu cable for Charger to battery (Flexible multi strand)

Termination with double compression Gland and Al lugs for 3 ½ core x 400 sqmm. Al cable.

Termination with double compression Gland and lugs 3 1/2 core x 150 sqmm. Al. cable

Termination with double compression Gland and lugs 2 core x 16 sqmm. Cu. Cable

Termination with double compression Gland and lugs 3 1/2 core x 150 sqmm. Al. cable

Termination with double compression Gland and lugs for 2core x 6 sqmm. Cu cable

Termination with double compression Gland and lugs for 4core x 16 sqmm.. Cable

Termination with double compression Gland and lugs for 2core x 16 sqmm.Cu cable

Termination with double compression Gland and lugs for 2core x 35 sqmm.. Cu cable

Termination with double compression Gland and lugs for1 core x 70 sqmm.. Crucible

Termination with double compression Gland and lugs for 3 corex 2.5 sqmm.Cu cable

ETC of Copper Control Cable

1100 V grade, PVC Insulated, PVC sheathed, steel round wire armoured, stranded control cables of the following sizes:

2 core 2.5 sqmm.

2 core 4 sqmm.

2 Core 6 sqmm.

4Core 4 sqmm.

4 core 2.5 sqmm.

7 core 2.5 sqmm.

12 core 2.5 sqmm.

19 Core 2.5 sqmm.

Double compression Glands and terminations (including ferruling, suitable Cu Lugs to meet the system requirements) for 1100 V grade PVC Insulated multicore Copper stranded conductor control cables of sizes: (2 core 2.5 sqmm.,2 core 4 sqmm., 2 Core 6 sqmm., 4Core 4 sqmm.,4Core 2.5 sqmm.7 core 2.5 sqmm,12 core 2.5 sqmm. &19 Core 2.5 sqmm.)

ETC of Cable Support & Cable Trays

Ladder type Cable Trays for outdoor

450 mm wide

300 mm wide

Perforated Cable Trays inside the Control Building

450 mm wide

300 mm wide

HDD/PVC pipe for laying cable from Trench to equipment

63 mm Dia

100 mm Dia

ETC of AC Distribution Board

AC 415V, 500A, 3-Ph cubicle type Indoor, floor mounted, auxiliary service board as per specification comprising of : (LVAC Board will have 2 sections , each section will be fed from independent Aux. transformer ( 250 KVA , 33/0.433 k V ).Busbar rating 600 A, 25 k A for 1 sec, Copper , IP 54 , 2 mm COLD ROLLED / 3 MM HOT ROLLED as aper specification )

ETC of DC Distribution Board ( 220 V DC & 48 VDC)

DC Distribution Board will have 2 sections , each section will be fed from independent Battery charger. Busbar rating 200 A FOR 220 V DC, 16 k A / FOR 1 SEC , AL or Copper , IP 54 , 2 mm COLD ROLLED / 3 MM HOT ROLLED) as per specification

DC Distribution Board will have 2 sections , each section will be fed from independent Battery charger. Busbar rating 200 A FOR 48 V DC, 16 k A / FOR 1 SEC , AL or Copper , IP 54 , 2 mm COLD ROLLED / 3 MM HOT ROLLED) as per specification

ETC of Battery and Battery charger

Battery set ( 220 V DC )

220V DC, 300 AH lead acid battery of VRLA type complete with accessories as per specification with 10% spare acid in non- returnable container (In tier arrangement).

Battery set ( 48 V DC )

48V DC, 200 AH lead acid battery of VRLA type complete with accessories as per specification with 10% spare acid in non- returnable container (In tier arrangement).

Battery charger ( 220 V DC )

Automatic float and Float cum boost charger 60 A suitable for 220 V 300 AH VRLA battery & charger shall be as per specification

Battery charger ( 48 V DC )

Automatic float and Float cum boost charger 50 A suitable for 48 V 200 AH VRLA battery & charger shall be as per specification

ETC of Fire fighting

NIFPS _ Nitrogen Injection Fire Fighting System System for Transformer

Fire Fighting equipment as per section-6 22.5 Kg capacity FE CO2 type, Trolley Mounted

25 Kg Capacity FE DCP type, Trolley Mounted

DCP 10 Kg Capacity, Wall mounted

FE CO2 6.5 Kg capacity, Wall mounted

DCP 5 Kg Capacity, Wall mounted

Foam Type 9 liter Capacity, Wall mounted

Water CO2 9 liter, Wall mounted

Fire Buckets (12 Nos. with stand in one set)

ETC of Outdoor illumination

LED flood light fitting with 250W led with all accessories control gear for Yard Lighting ( to be mounted on Gantry Tower )

LED flood light fitting with 250W led with all accessories control gear near boundary( to be mounted on 10 mtr. Pole)

LED street light fitting with 150W led with all accessories control gear on street ( to be mounted on 10 mtr. Pole)

70W LED lights post latern light mounted on 2.5 mtr. P-type pole

10 Mtr. MS Tubular poles 540SP-72

2.5 Mtr. P-type pole made of 100mm Dia GI Pipe

Lighting junction box for Light suitable for out door Installation comprising of 4 Nos. CBT M 4 type terminal connector for light connections Max size 150 x150x100mm

ETC of Air conditioning

Split unit for Control room (capacity 2 TR)

T&C of Measuring Instruments

Digital earth resistance meter

5 kV automated Insulation resistance meter

Earthing stick

Installation of Furniture

Executive Table :(1800mmX900mm)(Wooden)

Executive Chair:(Revolving mid back type)

Visitor's Chair with hand rest

Computer Room Executive Chair (Revolving mid back type)

2 nos. of Steel Almirah LengthXWidthXHeight in mm(1016X560X1980)

1 Nos. of Recta work station of size 1200mmX600mm,25 mm thick work top with 3 drawer pedestal along with keyboard tray and CPU trolley and partitions of thickness 53 mm and of height 1200 mm.

Description of Work / Item(s)

Amount

Towers in MT

Fabrication, galvanising and supply of various type of tower & tower parts, tower extensions (complete HT) including hangers, D- shackles, pack washer etc but excluding stubs. For LILO portion of the line

Fabrication, galvanising and supply of various type of tower & tower parts, tower extensions (complete MS) including hangers, D-shackles, pack washer etc but excluding stubs.

Fabrication, galvanising and supply of stubs & cleats for various type of towers, tower extensions (complete) with pack washers.

Supply of galvanised bolts & nuts for Towers & Stubs

Fabrication, galvanising and supply of various type of Templates, Templates extensions (complete) with pack washers, including bolts & nuts

2% variation in Tower parts for the existing line for any modification of Cross arms and other structural parts ( total weight of tower for 129 towers at average weight of 6.154 MT / tower)=794 MT

Variation in Nuts & Bolts for Tower X-Arms & other structural supports

Line Material

ACSR Panther Conductor

Earthwire 7/3.15 Steel

OPGW Cable (48 fibres)

ACSR Panther Conductor Insulator & Hardware

I) 90 KN String assembly Suspension

II) 120 KN String assembly Tension

Mid Span Compression Joints

Repair Sleeve

Vibration Dampers

Earthing

Pipe Type

Counterpoise

OPGW Accessories

Installation Hardware set for above 48Fibre OPGW Fibre Optic cabling including all cable fittings & accessories except joint box

Joint box (48 Fibres)

Fiber optic approach cable 48 fiber

Tower Accessories

I) Danger Plate

ii) Number Plate

iii) Phase Plate(sets of 3)

Description of Work / Item(s)

Amount

Towers in MT

Fabrication, galvanising and supply of various type of tower & tower parts, tower extensions (complete HT) including hangers, D- shackles, pack washer etc but excluding stubs. For LILO portion of the line

Fabrication, galvanising and supply of various type of tower & tower parts, tower extensions (complete MS) including hangers, D-shackles, pack washer etc but excluding stubs.

Fabrication, galvanising and supply of stubs & cleats for various type of towers, tower extensions (complete) with pack washers.

Supply of galvanised bolts & nuts for Towers & Stubs

Fabrication, galvanising and supply of various type of Templates, Templates extensions (complete) with pack washers, including bolts & nuts

2% variation in Tower parts for the existing line for any modification of Cross arms and other structural parts ( total weight of tower for 129 towers at average weight of 6.154 MT / tower)=794 MT

Variation in Nuts & Bolts for Tower X-Arms & other structural supports

Line Material

ACSR Panther Conductor

Earthwire 7/3.15 Steel

OPGW Cable (48 fibres)

ACSR Panther Conductor Insulator & Hardware

I) 90 KN String assembly Suspension

II) 120 KN String assembly Tension

Mid Span Compression Joints

Repair Sleeve

Vibration Dampers

Earthing

Pipe Type

Counterpoise

OPGW Accessories

Installation Hardware set for above 48Fibre OPGW Fibre Optic cabling including all cable fittings & accessories except joint box

Joint box (48 Fibres)

Fiber optic approach cable 48 fiber

Tower Accessories

I) Danger Plate

ii) Number Plate

iii) Phase Plate(sets of 3)

Description of Work / Item(s)

Amount

Erection Portion

Detail Survey as per tentative route which includes the following major activities-Pegging of line route, providing of survey pillar at an interval of 3-4 KM in the line route with required jungle clearance for survey, profile preparation of approved route on graph sheet and marking of offset on either side of the line, marking of side clearance for hills sand dunes etc as per specification and tower scheduling.

Check survey as per approved route of line which Includes Re-checklng of the line route as per approved profile, chainage. tower center marking, pit marking, bisection of angle tower as required at site.

Soil Investigation :Detailed Soil Investigation upto a depth of 7 mtr in soil and 3 Mtr in rock Strata in Normal conditions & 40 mtr in Special Locations.All kinds of soil except fissured rock & hard rock

Setting of template & stub/anchor bolt :Setting of template & stub/ anchor bolt & removal after concreting, excluding cost of excavation and concreting but including back filling with excavated/ borrowed earth (with lead & lift) in layers with ramming and watering as per specification. 132KV D/C Circuit Tower upto +6m, extension

Light angle Tower (B)

Heavy angle cum dead end Tower (D)

Concreting:RCC Work with Shuttering Providing and laying plain/reinforced cement concrete works using cement, coarse sand & 20mm down graded stone aggregate with cost of necessary form work including dewatering if necessary, and curing for reinforced cement concrete work complete as directed (Reinforcement will be measured and paid separately) In sub - structure up to plinth level

(i) M25 grade concrete

(ii) Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete. In prop 1cement: 3 sand :6 coarse aggregate by volume 1:3:6 Mix (M-10)

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL(i) TMT Corrosion resistant steel (CRS) reinforcement bar.

Earthing:

(A) Earthing of towers with pipe type earthing excluding the supply of pipes, wires, flats & connectors, but including coke/charcoal, etc., excavatlon, augering and backfilling in all types of soil.

(B) Earthing of towers with Counter-poise type earthing excluding the supply of pipes, wires, flats & connectors, but including coke/charcoal, etc., excavation, augering and backfilling in all types of soil.

Erection of Towers:Erection of super structures Including D-shackles, ACD, Hangers, U-Bolts, step bolts, danger plate, phase plate, number plate etc. Also Including tack welding of bolts & nuts up to bottom cross arm/beam level Including application of Zinc rich paint. 132KV Double Circuit Tower upto +6m, extension

ii) Light angle Tower (B)

Heavy angle cum dead end Tower (D)

Erection of Modification of x-Arms & other tower structures

Conductor Stringing : (A) Stringing of ACSR Panther Conductor Including hoisting of Insulator string, laying, Jointing & tensioning of conductor, clamping with Armour rods and fixing of vibration damper per route KM of the line.

(i) 3 conductor for S/C Line

OPGW Stringing Stringing of OPGW 48 Fibres Including associated accessories etc.

OPGW 48 Fibres

Line Material

Mid Span Compression Joints

Repair Sleeve

Vibration Dampers

Earthing

Pipe Type

Counterpoise

OPGW Accessories

Installation Hardware set for above 48Fibre OPGW Fibre Optic cabling including all cable fittings & accessories except joint box

Joint box (48 Fibres)

Fiber optic approach cable 48 fiber

Description of Work / Item(s)

Amount

Part A - Site development work

Surface dressing of ground including removing vegetation and/ or undulation of ground not exceeding 150mm deep and disposal of rubbish outside the periphery and lift up to 1800mm in all kinds of soil.

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete . (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Supplying and laying 150 mm thick machine crushed 40 mm and 20 mm blue stone aggregates in layers. Bottom layer of 50 mm thickness with 20 mm size aggregates uniformly spread and compacted and Top layer 100 mm thick with 40mm aggregate to be spread uniformly and compacted.

Part B - Trenches work

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works using cement, coarse sand & 20mm down graded stone aggregate with cost of necessary form work including dewatering if necessary, and curing for reinforced cement concrete work complete as directed (Reinforcement will be measured and paid separately) Using mixture machine In sub - structure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level.M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code forR.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Structure Steel Structural steel work in sigle sections including cutting, hoisting, fixing in position and applying a priming coat of red lead paint (up to 4.6m height) from plinth level including drilling holes, supplying, fitting and fixing with bolts and nuts or welding, if necessary as directed. c) In M.S. angles, channels, Tees etc.

Providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to IS 13592 type a including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. (i) single socketed pipes 110mm diameter

Part C (i) - Approach Road

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified. (ii) Other than Guwahati city

Construction of Sub-grade and earthen shoulders with approved materials obtained from borrow pits, with all lifts & leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 (including compensation of earth ). (Including cost of testing of materials at site and laboratory as directed by the deptt.) a) from Private land

Construction of Granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per Clause 401 of MoRTH specifications (with an initial lead of 5 km) (including cost of testing of materials at site and laboratory as directed by the deptt.) (iii)Using Grading III material

Construction of (WBM) by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per Clause 401 of MoRTH specifications (with an initial lead of 5 km) (including cost of testing of materials at site and laboratory as directed by the deptt.) (i)Using Grading I material

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 3 sand :6 coarse aggregate by volume

Providing and laying of inter locking concrete block pavement (ICBP) with cement concrete paver blocks as per IS 15658-2006 of thickness 80mm and 28 days compressive strength not less than 30 N/m over a layer of bedding sand of compacted thickness 30mm, laid either in stretcher/ running/ herringbone pattern of bonds as directed by the engineer and in proper level and grade and compacted with appropriate equipment such as plat vibrator along with spreading of a thin layer of joint filling sand to fill up the gaps between blocks including construction of edge restraint wherever required complete as per drawings and Technicalspecification clause 1504 of MORD.

Part C (ii) - Internal Road

Construction of Sub-grade and earthen shoulders with approved materials obtained from borrow pits, with all lifts & leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 (including compensation of earth ). (Including cost of testing of materials at site and laboratory as directed by the deptt.) a) from Private land

Construction of Granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per Clause 401 of MoRTH specifications (with an initial lead of 5 km) (including cost of testing of materials at site and laboratory as directed by the deptt.) (iii)Using Grading III material

Construction of (WBM) by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per Clause 401 of MoRTH specifications (with an initial lead of 5 km) (including cost of testing of materials at site and laboratory as directed by the deptt.) (i)Using Grading I material

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 3 sand :6 coarse aggregate by volume

Providing and laying of inter locking concrete block pavement (ICBP) with cement concrete paver blocks as per IS 15658-2006 of thickness 80mm and 28 days compressive strength not less than 30 N/m over a layer of bedding sand of compacted thickness 30mm, laid either in stretcher/ running/ herringbone pattern of bonds as directed by the engineer and in proper level and grade and compacted with appropriate equipment such as plat vibrator along with spreading of a thin layer of joint filling sand to fill up the gaps between blocks including construction of edge restraint wherever required complete as per drawings and Technical specification clause 1504 of MORD.

Part D (i) - Boundary/Retaining wall

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using Mixer Machine

In substructure up to plinth level ;- Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

In super structure from plinth level up to 1st floor level. Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code forR.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

Vertical surface such as walls (any thickness), parapet walls, partitions and the like including attached pilasters, butresses, plinth and string courses and the like.

Stone masonary work in retaining wall, wing wall, abutment, foundation, steps, plinth etc. in cement mortar in prop 1:6 with levelling course of 1:6:12 with both faces hammer dressed including bonding, providing face stone, through stone and centering including racking of joints, curing and supplying and all carriage of stone as directed including payment of forest royalty and sales tax and carriage. (b) Coarse Rubble Masonry

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (II) In superstructure above plinth level up to 1st floor level. (d) In proportion 1:6.(1 cement:6 sand)

External Plaster work with water proofing materials ; - 20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. B. On fair side (backing coat 10 mm and finishing coat 10mm thick) (b) In cement mortar 1:4.

b) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new wall surface (two coats) to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials.

Structural steel work in sigle sections including cutting, hoisting, fixing in position and applying a priming coat of red lead paint (up to 4.6m height) from plinth level including drilling holes, supplying, fitting and fixing with bolts and nuts or welding, if necessary as directed. c) In M.S. angles, channels, Tees etc.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in- charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S.

Part D (ii) - Fence wall

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works using cement, coarse sand & 20mm down graded stone aggregate with cost of necessary form work including dewatering if necessary, and curing for reinforced cement concrete work complete as directed (Reinforcement will be measured and paid separately) Using mixture machine In sub - structure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Brickwork with Plastering : Brick work in cement mortar with 1st class brick including cement motar plastering, racking out joints and curing complete as directed in superstructure above plinth level up to 1st floor level. Both side plastering With fair side 10mm thick and rough side 15mm thick plasteringi) In prop. 1:4 b) Brick work in cement morter proportion 1:6

Structure Steel :-Structural steel work in sigle sections including cutting, hoisting, fixing in position and applying a priming coat of red lead paint (up to 4.6m height) from plinth level including drilling holes, supplying, fitting and fixing with bolts and nuts or welding, if necessary as directed. c) In M.S. angles, channels, Tees etc.

Supplying, fitting and fixing chain link fencing of 10 S.W.G, G.I. Wire 50mm x50mm mesh fitted to M.S angle iron post at 2000mm apart of specification detailed below including supplying, fitting and fixing hooks, eye bolts with nuts, staples and bolts including three horizontal lines of G.I wire 10S.W.G at top,middle and bottom and with one vertical line to each fencing post for keeping the fencing tight and erect complete, including one coat of primer painting to M.S angle iron post in P.C.C base etc. with following. a) Corner and end posts with M.S angle of size 50mmx50mmx 5mm and length not less than 1800mm only duly slotted and bottom torqued with two numbers as stay posts.. b). Intermediate post with M.S angle of size 40mmx40mmx5mm and length not less than 1800mm only duly slotted and bottom torqued and splayed. c).Stay post with M.S angle of size 35 mmx35mmx5mm and length not less than 1800mm duly slotted and bottom torqued and splayed. All M.S angle iron posts are to be fitted to P.C.C base embedded not less than 600mm (P.C.C. work shall be measured and paid separately).

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in- charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately).

Part E (i) - External drainage work

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

Providing and laying plain/reinforced cement croncrete works using cement, coarse sand & 20mm down graded stone aggregate with cost of necessary form work including dewatering if necessary, and curing for reinforced cement concrete work complete as directed (Reinforcement will be measured and paid separately) Using mixture machineIn sub - structure up to plinth level

Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M15 or Prop. 1:2:4

Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Brickwork with Plastering :- Brick work in cement mortar with 1st class brick including cement motar plastering, racking out joints and curing complete as directed in superstructure above plinth level up to 1st floor level. Both side plastering With fair side 10mm thick and rough side 15mm thick plastering i) In prop. 1:4 b) Brick work in cement morter proportion 1:6

Structure Steel : Structural steel work in sigle sections including cutting, hoisting, fixing in position and applying a priming coat of red lead paint (up to 4.6m height) from plinth level including drilling holes, supplying, fitting and fixing with bolts and nuts or welding, if necessary as directed. c) In M.S. angles, channels, Tees etc.

Supplying and laying of following size NP2 class RCC Hume pipe i/c collars jointed with stiff mixture of cement morter 1:2 ( 1 cement:2 fine sand) across the road including cutting the road ( if reqd) digging the trench, refilling the same after laying pipe, ramming the soil etc as reqd. (b) 300 mm dia

Part E (ii) - Rain water harvesting

Providing,Fixing, testing &Commissioning of Rain water Hervesting system for 1000 sq.feet roof area with 110 mm uPVC pipe of Class-3 conforming to IS:4985-200 (with uptodate amendment) with extra UV ray protection by Titanium Dioxide(TiO2) directing the Rainwater to Rainy filter/Pop-up raintap filter (Excluding Civil Works)

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Brickwork with Plastering :- Brick work in cement mortar with 1st class brick including cement motar plastering, racking out joints and curing complete as directed in superstructure above plinth level up to 1st floor level. Both side plastering With fair side 10mm thick and rough side 15mm thick plastering i) In prop. 1:4 b) Brick work in cement morter proportion 1:6

Part F (i) - Control room building

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.5.1 SOR of APWD) UNIFORM PILE Concrete Grade M25

Pile dia 400 mm, 9.0+3.5=12.5m long pile 10 nos

Pile dia 500 mm, 9.0+3.5=12.5m long pile 65 nos

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) TMT bar made of Primary producer (From Primary producer)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using Mixer Machine

In substructure up to plinth level : Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

In super structure from plinth level up to 1st floor level. Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in:

Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like.Floors etc. upto 200mm in thickness.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (I) In Sub-structure upto plinth level including dewatering if necessary (d) In proportion 1:6.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (II) In superstructure above plinth level up to 1st floor level. (d) In proportion 1:6.(1 cement:6 sand)

Celling Plaster work :- 10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. (a) In cement mortar 1:3

Internal Plaster work :- 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A. On rough side (b) In cement mortar 1:4

External Plaster work with water proofing materials : - 20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. B. On fair side (backing coat 10 mm and finishing coat 10mm thick) (b) In cement mortar 1:4

Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. 100mm thick

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) Normal range (600mmx600mm and above) i) Somany Made a) Digital- Gold VC

B) AT WALLS : - Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). Executive range- 1 (Sizes 300 mm x450mm and above) i) Somany made a) Gold

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (A) CERAMIC i) Normal range (Sizes 300 mm x 300mm and above)

Providing polished granite tiles of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

Chequered Terrazo tiles of 22 mm thickness with marble chips of sizes up to 6 mm fixed on wall with 10 mm thick bed of cement plaster in proportion 1:3 (1 cement : 3 coarse sand) jointed with neat white cement slurry mixed with pigment to match the shades of tiles including rubbing and polishing complete with tiles of any approved shade/shades. a) Using white cement on ramp

Removing white or colour wash by steel wire brushing and/ or scraping, sand papering and preparing the wall surface smooth including necessary repairs to scratches complete.

Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing two coats of J.K Wall Putty ( White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Finishing old / new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint of required shade after cleaning and clearing the surface etc.including scaffolding complete as directed at all levels (two coats).

Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels.

Providing and laying six course water proof treatment with bitumen felt over roof consisting of first, third and fifth courses of blown or residual bitumen applied hot @ 1.45kg, 1.20kg and 1.45kg per sq.m of areas respectively, second and fourth courses of roofing with felt type 3 grade - I (hessain base self finished bitumen felt) and sixth and final course with stone grit 6mm and down per sq.m including preparation of surface, excluding grading complete.

Supplying, providing, mixing and laying over waterproofing layers/ coatings with concrete screed of average 30mm thick or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with 10mm and down well graded aggregates and admixed with a normal plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 430x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and CP brass spreaders with brass unios and GI clamps complete including painting of fitting and brackets cutting and making good the walls and floors wherever required One urinal basin with 5 ltr white PVC automatic flushing cistern

Providing and fixing wash basin with CI brackets 15mm CP brass pillar taps 32mm CP brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White vitreous china wash basin size 630x450mm with a pair of 15 mm CP brass pillar taps

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 610x510 mm bowl depth 200 mm

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Supplying fitting and fixing supreme brand / Prince brand or similar approved P.V.C. Pipes of following sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. ii) PRINCE BRAND (High presure pipe Sch-40) Exposed or in trenches

15mm nominal bore

20mm nominal bore

25mm nominal bore

32mm nominal bore

40mm nominal bore

50mm nominal bore

Providing and fixing 100mm sand cast iron grating for gully trap

Providing and laying and jointing glazed stoneware pipes grade "A" with stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement 1 fine sand ) including testing of joints etc. complete

100 mm diameter

150 mm diameter

Providing and fixing square mouth SW gully trap grade :A: complete with CI grating brick masonry chamber with water tight CI cover with frame of 300x300mm size(inside) the weighing of cover to be not less than 4.50kg and frame to be not less than 2.70kg as per standard design 100x100mm size P type With FPS bricks class designation 75

Providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to IS 13592 type a including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. (i) single socketed pipes 110mm diameter

Sintex Water Tank,2000 Litres capacity

Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration rate per hour of TARUS make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six monthhs (A)REVERSE OSMOSIS (R.O)-For best Quality Drinking Water B) KENT Grand +,15 lph,8 litres storage

Providing and laying non- pressure NP2 class (light duty) RCC pipes with collars joints with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement 2 fine sand ) including testing of joints etc, complete 150 mm dia RCC pipe

Constructing brick masonry circular type manhole 0.91mm internal dia at bottom and 0.56m dia at top in cement mortar 1:4( 1 cement 4 coarse sand ) in side cement plaster 12mm thick with cement mortar 1:3( 1 cement 3 coarse sand ) finished with a floating coat of neat cement foundation concrete 1:3:6( 1 cement 3 coarse sand 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design 0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to IS 12592 total weight of cover and frame to be not less than 182 kg, fixed in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stones aggregate 20mm nominal size) including centering shuttering all complete at the external surface shall be paid for separately) With FPS bricks with class designation 75

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels. (Cement concrete to be measured and paid separately). a)Side hung and Top hung windows and ventilators i) 6 mm clear glass

Providing, fitting and fixing Coloured anodised aluminuim framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm lock rails 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete including hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc complete as specified and directed by the department at all levels. (i)6mm clear glass

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete.

Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in-Charge.

In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand).

In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand).

Light & fan Point (First Point)

Light & fan Point (second Point)

Call bell point including MS Box of Size 180mmx100mmx60mm deep for Call bell

3 pin 6 amp plug point including earthing the 3rd pin (power Point)

3 pin 16 amp plug point including earthing the 3rd pin (power Point)

Supply & erection of PVC Copper insulated & sheathed 2 Wire circular flexible wire size 4Sq.mm(power point)

Supply & erection of PVC sheathed copper conductor cable single core 1100V grade in sizing 6 Sq mm ( AC Point)

supply & errection of 25 Amp DP MCCB (AC point)

supply & errection of 16 Amp DP MCCB (Exhaust fan point)

Supply & erection of sheet steel enclosure distribution board suitable for MCB,s etc on wall with rag bolts -12 Way (Three Pole) Including SPMCB 10 No 6-32A & incomer DPMCB 63 A

Supply & erection of MCCB on wall or on pedestal including bonding to earth & necessary with connections-200Amp,415 V ,3phase

Supply & erection of MCB in existing distribution board including making connection complete

16 Amps SPMCB

25 Amps SPMCB

40 Amps DP MCB

63 Amps FPMCB

Call bell 220/230V with double coil

Bell Push

Supply & erection of 10.5cm dia MS Fan boxes

Supply & erection of 9W LED

Supply & erection 2x24W led tube light

Supply & erection 5w led light

Ceiling Fans,1400mm Sweep (USHA/CGL)

Industrial type Exhaust Fans, 1400 RPM,18 Inches

Industrial Power Socket 32 Amps

Cable from ACDB to distribution board Al ( 4C x 35 sq mm)

Part F (ii) - Officers Hostel

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.5.1 SOR of APWD) UNIFORM PILE ( Concrete Grade M25 )

400mm dia, 9.0+3.5=12.5 m long pile 44 nos

500mm dia, 9.0+3.5=12.5 m long pile 16 nos

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) TMT bar made of Primary producer (From Primary producer)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using Mixer Machine

In substructure up to plinth level : Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

In super structure from plinth level up to 1st floor level. Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in:

Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200mm in thickness.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (I) In Sub-structure upto plinth level including dewatering if necessary (d) In proportion 1:6.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (II) In superstructure above plinth level up to 1st floor level. (d) In proportion 1:6.(1 cement:6 sand)

Celling Plaster work :- 10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing (a) In cement mortar 1:3

Internal Plaster work : - 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A. On rough side (b) In cement mortar 1:4

External Plaster work with water proofing materials : - 20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. B. On fair side (backing coat 10 mm and finishing coat 10mm thick) (b) In cement mortar 1:4

Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. 100mm thick

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) Normal range (600mmx600mm and above) i) Somany Made a) Digital- Gold VC

B) AT WALLS Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). Executive range- 1 (Sizes 300 mm x450mm and above) i) Somany made a) Gold

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A- Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (A) CERAMIC i)Normal range (Sizes 300 mm x 300mm and above)

Providing polished granite tiles of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

(a) Removing white or colour wash by steel wire brushing and/ or scraping, sand papering and preparing the wall surface smooth including necessary repairs to scratches complete.

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing two coats of J.K Wall Putty ( White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Finishing old / new wall with water proofing weather coat smooth anti-fungal exterior painting ofapproved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats).

Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels.

Providing and laying six course water proof treatment with bitumen felt over roof consisting of first, third and fifth courses of blown or residual bitumen applied hot @ 1.45kg, 1.20kg and 1.45kg per sq.m of areas respectively, second and fourth courses of roofing with felt type 3 grade - I (hessain base self finished bitumen felt) and sixth and final course with stone grit 6mm and down per sq.m including preparation of surface, excluding grading complete.

Supplying, providing, mixing and laying over waterproofing layers/ coatings with concrete screed of average 30mm thick or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with 10mm and down well graded aggregates and admixed with a normal plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with CI brackets 15mm CP brass pillar taps 32mm CP brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White vitreous china wash basin size 630x450mm with a pair of 15 mm CP brass pillar taps

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 610x510 mm bowl depth 200 mm

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Supplying fitting and fixing supreme brand / Prince brand or similar approved P.V.C. Pipes of following sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. ii) PRINCE BRAND (High presure pipe Sch-40) Exposed or in trenches

15mm nominal bore

20mm nominal bore

25mm nominal bore

32mm nominal bore

40mm nominal bore

50mm nominal bore

Making connection of GI distribution branch with GI main of following sizes by providing and fixing tee including cutting and threading the pipe ect complete

25 to 40mm nominal bore

50 to 80mm nominal bore

Providing and fixing 100mm sand cast iron grating for gully trap

Providing and laying and jointing glazed stoneware pipes grade "A" with stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement 1 fine sand ) including testing of joints etc. complete

100 mm diameter

150 mm diameter

Providing and fixing square mouth SW gully trap grade :A: complete with CI grating brick masonry chamber with water tight CI cover with frame of 300x300mm size(inside) the weighing of cover to be not less than 4.50kg and frame to be not less than 2.70kg as per standard design 100x100mm size P type With FPS bricks class designation 75

Providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to IS 13592 type a including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. (i) single socketed pipes110mm diameter

Sintex Water Tank,2000 Litres capacity

Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration rate per hour of TARUS make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six monthhs (F)REVERSE OSMOSIS (R.O)-For best Quality Drinking Water (I) KENT Grand +,15 lph,8 litres storage

Providing and laying non- pressure NP2 class (light duty) RCC pipes with collars joints with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement 2 fine sand ) including testing of joints etc, complete 150 mm dia RCC pipe

Constructing brick masonry circular type manhole 0.91mm internal dia at bottom and 0.56m dia at top in cement mortar 1:4( 1 cement 4 coarse sand ) in side cement plaster 12mm thick with cement mortar 1:3( 1 cement 3 coarse sand ) finished with a floating coat of neat cement foundation concrete 1:3:6( 1 cement 3 coarse sand 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design 0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to IS 12592 total weight of cover and frame to be not less than 182 kg, fixed in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stones aggregate 20mm nominal size) including centering shuttering all complete at the external surface shall be paid for separately) With FPS bricks with class designation 75

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels. (Cement concrete to be measured and paid separately). a)Side hung and Top hung windows and ventilators i) 6 mm clear glass

Providing, fitting and fixing Coloured anodised aluminuim framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm lock rails 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete including hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc complete as specified and directed by the department at all levels. (i)6mm clear glass

Providing plinth protection with bricks flat laid in cement mortar 1:4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Light & fan Point (First Point)

Light & fan Point (second Point)

Call bell point including MS Box of Size 180mmx100mmx60mm deep for Call bell

3 pin 6 amp plug point including earthing the 3rd pin (power Point)

3 pin 16 amp plug point including earthing the 3rd pin (power Point)

Supply & erection of PVC Copper insulated & sheathed 2 Wire circular flexible wire size 4Sq.mm(power point)

Supply & erection of PVC sheathed copper conductor cable single core 1100V grade in sizing 6 Sq mm ( AC Point)

supply & errection of 25 Amp DP MCCB (AC point)

Supply & erection of sheet steel enclosure distribution board suitable for MCB,s etc on wall with rag bolts -12 Way (Three Pole) Including SPMCB 10 No 6-32A & incomer DPMCB 63 A

Supply & erection of MCCB on wall or on pedestal including bonding to earth & necessary connections-200Amp,415 V ,3phase

Supply & erection of MCB in existing distribution board including making connection complete

16 Amps SPMCB

25 Amps SPMCB

40 Amps DP MCB

Call bell 220/230V with double coil

Bell Push

Supply & erection of 10.5cm dia MS Fan boxes

Supply & erection of 9W LED

Supply & erection 2x24W led tube light

Supply & erection 5w led light

Supply & erection 12w led light

Ceiling Fans,1400mm Sweep (USHA/CGL)

Exhaust Fans

Industrial Power Socket 32 Amps

Cable from ACDB to distribution board Al ( 4C x 35 sq mm)

Part F (iii) - RE'S residence building

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.5.1) UNIFORM PILE Concrete Grade M25 400mm dia, 9.0+3.5=12.5 m long pile 28 nos

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) TMT bar made of Primary producer (From Primary producer)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using Mixer Machine

In substructure up to plinth level : -Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

In super structure from plinth level up to 1st floor level. Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in:

Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200mm in thickness.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (I) In Sub-structure upto plinth level including dewatering if necessary (d) In proportion 1:6.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (II) In superstructure above plinth level up to 1st floor level. (d) In proportion 1:6.(1 cement:6 sand)

Celling Plaster work : 10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. (a) In cement mortar 1:3

Internal Plaster work: 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A. On rough side (b) In cement mortar 1:4

External Plaster work with water proofing materials: 20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. B. On fair side (backing coat 10 mm and finishing coat 10mm thick) (b) In cement mortar 1:4

Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. 100mm thick

VITRIFIED TILES A) AT FLOOR Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) Normal range (600mmx600mm and above) i) Somany Made a) Digital- Gold VC

B) AT WALLS : Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). Executive range- 1 (Sizes 300 mm x450mm and above) i) Somany made a) Gold

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A- Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (A) CERAMIC i)Normal range (Sizes 300 mm x 300mm and above)

Providing polished granite tiles of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

(a) Removing white or colour wash by steel wire brushing and/ or scraping, sand papering and preparing the wall surface smooth including necessary repairs to scratches complete.

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing two coats of J.K Wall Putty ( White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Finishing old / new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats).

Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels.

Providing and laying six course water proof treatment with bitumen felt over roof consisting of first, third and fifth courses of blown or residual bitumen applied hot @ 1.45kg, 1.20kg and 1.45kg per sq.m of areas respectively, second and fourth courses of roofing with felt type 3 grade - I (hessain base self finished bitumen felt) and sixth and final course with stone grit 6mm and down per sq.m including preparation of surface, excluding grading complete.

Supplying, providing, mixing and laying over waterproofing layers/ coatings with concrete screed of average 30mm thick or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with 10mm and down well graded aggregates and admixed with a normal plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 430x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and CP brass spreaders with brass unios and GI clamps complete including painting of fitting and brackets cutting and making good the walls and floors wherever required One urinal basin with 5 ltr white PVC automatic flushing cistern

Providing and fixing wash basin with CI brackets 15mm CP brass pillar taps 32mm CP brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White vitreous china wash basin size 630x450mm with a pair of 15 mm CP brass pillar taps

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 610x510 mm bowl depth 200 mm

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Supplying fitting and fixing supreme brand / Prince brand or similar approved P.V.C. Pipes of following sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. ii) PRINCE BRAND (High presure pipe Sch-40) Exposed or in trenches

15mm nominal bore

20mm nominal bore

25mm nominal bore

32mm nominal bore

40mm nominal bore

50mm nominal bore

Making connection of GI distribution branch with GI main of following sizes by providing and fixing tee including cutting and threading the pipe ect complete

25 to 40mm nominal bore

50 to 80mm nominal bore

Providing and fixing 100mm sand cast iron grating for gully trap

Providing and laying and jointing glazed stoneware pipes grade "A" with stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement 1 fine sand ) including testing of joints etc. complete

100 mm diameter

150 mm diameter

Providing and fixing square mouth SW gully trap grade :A: complete with CI grating brick masonry chamber with water tight CI cover with frame of 300x300mm size(inside) the weighing of cover to be not less than 4.50kg and frame to be not less than 2.70kg as per standard design 100x100mm size P type With FPS bricks class designation 75

Providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to IS 13592 type a including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. (i) single socketed pipes 110mm diameter

Sintex Water Tank,2000 Litres capacity

Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration rate per hour of TARUS make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six monthhs (F)REVERSE OSMOSIS (R.O)-For best Quality Drinking Water (I) KENT Grand +,15 lph,8 litres storage

Providing and laying non- pressure NP2 class (light duty) RCC pipes with collars joints with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement 2 fine sand ) including testing of joints etc, complete 150 mm dia RCC pipe

Constructing brick masonry circular type manhole 0.91mm internal dia at bottom and 0.56m dia at top in cement mortar 1:4( 1 cement 4 coarse sand ) in side cement plaster 12mm thick with cement mortar 1:3( 1 cement 3 coarse sand ) finished with a floating coat of neat cement foundation concrete 1:3:6( 1 cement 3 coarse sand 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design 0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to IS 12592 total weight of cover and frame to be not less than 182 kg, fixed in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stones aggregate 20mm nominal size) including centering shuttering all complete at the external surface shall be paid for separately) With FPS bricks with class designation 75

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels. (Cement concrete to be measured and paid separately). a)Side hung and Top hung windows and ventilators i) 6 mm clear glass

Providing, fitting and fixing Coloured anodised aluminuim framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm lock rails 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete including hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc complete as specified and directed by the department at all levels. (i)6mm clear glass

Providing plinth protection with bricks flat laid in cement mortar 1:4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Light & fan Point (First Point)

Light & fan Point (second Point)

Call bell point including MS Box of Size 180mmx100mmx60mm deep for Call bell

3 pin 6 amp plug point including earthing the 3rd pin (power Point)

3 pin 16 amp plug point including earthing the 3rd pin (power Point)

Supply & erection of PVC Copper insulated & sheathed 2 Wire circular flexible wire size 2.50 Sq.mm(power point)

Supply & erection of PVC sheathed copper conductor cable single core 1100V grade in sizing 4Sq mm ( AC Point)

supply & errection of 25 Amp DP MCCB (AC point)

Supply & erection of sheet steel enclosure distribution board suitable for MCB,s etc on wall with rag bolts -12 Way (Three Pole) Including SPMCB 10 No 6-32A & incomer DPMCB 63 A

Supply & erection of MCCB on wall or on pedestal including bonding to earth & necessary connections-200Amp,415 V ,3phase

Supply & erection of MCB in distribution board including making connection complete with

16 Amps SPMCB

25 Amps SPMCB

40 Amps DP MCB

63 Amps FPMCB

Call bell 220/230V with double coil

Bell Push

Supply & erection of 10.5cm dia MS Fan boxes

Supply & erection of 9W LED

Supply & erection 2x24W led tube light

Supply & erection 5w led light

Supply & erection 12w led light

Ceiling Fans,1400mm Sweep (USHA/CGL)

Exhaust Fans

Industrial Power Socket 32 Amps

Cable from ACDB to distribution board Al ( 4C x 35 sq mm)

Part F (iv) - Staff hostel building

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.5.1) UNIFORM PILE Concrete Grade M25

400mm dia, 9.0+3.5=12.5 m long pile 16 nos

500mm dia, 9.0+3.5=12.5 m long pile 24 nos

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) TMT bar made of Primary producer (From Primary producer)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using Mixer Machine

In substructure up to plinth level :-Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

In super structure from plinth level up to 1st floor level.: Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in:

Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200mm in thickness.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (I) In Sub-structure upto plinth level including dewatering if necessary (d) In proportion 1:6.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (II) In superstructure above plinth level up to 1st floor level. (d) In proportion 1:6.(1 cement:6 sand)

Celling Plaster work :- 10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. (a) In cement mortar 1:3

Internal Plaster work: -15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A. On rough side (b) In cement mortar 1:4

External Plaster work with water proofing materials : -20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. B. On fair side (backing coat 10 mm and finishing coat 10mm thick) (b) In cement mortar 1:4

Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. 100mm thick

VITRIFIED TILES A) AT FLOOR Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) Normal range (600mmx600mm and above) i) Somany Made a) Digital- Gold VC

B) AT WALLS : -Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). Executive range- 1 (Sizes 300 mm x450mm and above) i) Somany made a) Gold

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A- Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (A) CERAMIC i)Normal range (Sizes 300 mm x 300mm and above)

Providing polished granite tiles of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

(a) Removing white or colour wash by steel wire brushing and/ or scraping, sand papering and preparing the wall surface smooth including necessary repairs to scratches complete.

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing two coats of J.K Wall Putty ( White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICIpaint/ J & N paint/ Nerolac)

Finishing old / new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats).approved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats).

Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels.

Providing and laying six course water proof treatment with bitumen felt over roof consisting of first, third and fifth courses of blown or residual bitumen applied hot @ 1.45kg, 1.20kg and 1.45kg per sq.m of areas respectively, second and fourth courses of roofing with felt type 3 grade - I (hessain base self finished bitumen felt) and sixth and final course with stone grit 6mm and down per sq.m including preparation of surface, excluding grading complete.

Supplying, providing, mixing and laying over waterproofing layers/ coatings with concrete screed of average 30mm thick or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with 10mm and down well graded aggregates and admixed with a normal plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 430x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and CP brass spreaders with brass unios and GI clamps complete including painting of fitting and brackets cutting and making good the walls and floors wherever required One urinal basin with 5 ltr white PVC automatic flushing cistern

Providing and fixing wash basin with CI brackets 15mm CP brass pillar taps 32mm CP brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White vitreous china wash basin size 630x450mm with a pair of 15 mm CP brass pillar taps

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 610x510 mm bowl depth 200 mm

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Supplying fitting and fixing supreme brand / Prince brand or similar approved P.V.C. Pipes of following sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. ii) PRINCE BRAND (High presure pipe Sch-40) Exposed or in trenches

15mm nominal bore

20mm nominal bore

25mm nominal bore

32mm nominal bore

40mm nominal bore

50mm nominal bore

Making connection of GI distribution branch with GI main of following sizes by providing and fixing tee including cutting and threading the pipe ect complete

25 to 40mm nominal bore

50 to 80mm nominal bore

Providing and fixing 100mm sand cast iron grating for gully trap

Providing and laying and jointing glazed stoneware pipes grade "A" with stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement 1 fine sand ) including testing of joints etc. complete

100 mm diameter

150 mm diameter

Providing and fixing square mouth SW gully trap grade :A: complete with CI grating brick masonry chamber with water tight CI cover with frame of 300x300mm size(inside) the weighing of cover to be not less than 4.50kg and frame to be not less than 2.70kg as per standard design 100x100mm size P type With FPS bricks class designation 75

Providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to IS 13592 type a including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. (i) single socketed pipes 110mm diameter

Sintex Water Tank,2000 Litres capacity

Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration rate per hour of TARUS make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six monthhs (F)REVERSE OSMOSIS (R.O)-For best Quality Drinking Water (I) KENT Grand +,15 lph,8 litres storage

Providing and laying non- pressure NP2 class (light duty) RCC pipes with collars joints with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement 2 fine sand ) including testing of joints etc, complete 150 mm dia RCC pipe

Constructing brick masonry circular type manhole 0.91mm internal dia at bottom and 0.56m dia at top in cement mortar 1:4( 1 cement 4 coarse sand ) in side cement plaster 12mm thick with cement mortar 1:3( 1 cement 3 coarse sand ) finished with a floating coat of neat cement foundation concrete 1:3:6( 1 cement 3 coarse sand 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design 0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to IS 12592 total weight of cover and frame to be not less than 182 kg, fixed in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stones aggregate 20mm nominal size) including centering shuttering all complete at the external surface shall be paid for separately) With FPS bricks with class designation 75

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels. (Cement concrete to be measured and paid separately). a)Side hung and Top hung windows and ventilators i) 6 mm clear glass

Providing, fitting and fixing Coloured anodised aluminuim framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm lock rails 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete including hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc complete as specified and directed by the department at all levels. (i)6mm clear glass

Providing plinth protection with bricks flat laid in cement mortar 1:4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Light & fan Point (First Point)

Light & fan Point (second Point)

Call bell point including MS Box of Size 180mmx100mmx60mm deep for Call bell

3 pin 6 amp plug point including earthing the 3rd pin (power Point)

3 pin 16 amp plug point including earthing the 3rd pin (power Point)

Supply & erection of PVC Copper insulated & sheathed 2 Wire circular flexible wire size 4Sq.mm(power point)

Supply & erection of PVC sheathed copper conductor cable single core 1100V grade in sizing 6 Sq mm ( AC Point)

supply & errection of 25 Amp DP MCCB (AC point)

Supply & erection of sheet steel enclosure distribution board suitable for MCB,s etc on wall with rag bolts -12 Way (Three Pole) Including SPMCB 10 No 6-32A & incomer DPMCB 63 A

Supply & erection of MCCB on wall or on pedestal including bonding to earth & necessary connections-200Amp,415 V ,3phase

Supply & erection of MCB in existing distribution board including making connection complete with

16 Amps SPMCB

25 Amps SPMCB

40 Amps DP MCB

Call bell 220/230V with double coil

Bell Push

Supply & erection of 10.5cm dia MS Fan boxes

Supply & erection of 9W LED

Supply & erection 2x24W led tube light

Supply & erection 5w led light

Supply & erection 12w led light

Ceiling Fans,1400mm Sweep (USHA/CGL)

Exhaust Fans

Industrial Power Socket 32 Amps

Cable from ACDB to distribution board Al ( 4C x 35 sq mm)

Part F (v) - Security barrack

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.5.1) UNIFORM PILE Concrete Grade M25 400mm dia, 9.0+3.5=12.5 m long pile 24 nos

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) TMT bar made of Primary producer (From Primary producer)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using Mixer Machine

In substructure up to plinth level : -Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

In super structure from plinth level up to 1st floor level.:-Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in:

Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200mm in thickness.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (I) In Sub-structure upto plinth level including dewatering if necessary (d) In proportion 1:6.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (II) In superstructure above plinth level up to 1st floor level. (d) In proportion 1:6.(1 cement:6 sand)

Celling Plaster work:- 10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. (a) In cement mortar 1:3

Internal Plaster work:-15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A. On rough side (b) In cement mortar 1:4

External Plaster work with water proofing materials:-20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. B.On fair side (backing coat 10 mm and finishing coat 10mm thick) (b) In cement mortar 1:4

Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. 100mm thick

VITRIFIED TILES :- A) AT FLOOR Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) Normal range (600mmx600mm and above) i) Somany Made a) Digital- Gold VC

B) AT WALLS :_ Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). Executive range- 1 (Sizes 300 mm x450mm and above) i) Somany made a) Gold

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A- Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (A) CERAMIC i)Normal range (Sizes 300 mm x 300mm and above)

Providing polished granite tiles of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

Chequered Terrazo tiles of 22 mm thickness with marble chips of sizes up to 6 mm fixed on wall with 10 mm thick bed of cement plaster in proportion 1:3 (1 cement : 3 coarse sand) jointed with neat white cement slurry mixed with pigment to match the shades of tiles including rubbing and polishing complete with tiles of any approved shade/shades. (a) Using white cement on ramp

(a) Removing white or colour wash by steel wire brushing and/ or scraping, sand papering and preparing the wall surface smooth including necessary repairs to scratches complete.

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing two coats of J.K Wall Putty ( White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICIpaint/ J & N paint/ Nerolac)

Finishing old / new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats).

Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels.

Providing and laying six course water proof treatment with bitumen felt over roof consisting of first, third and fifth courses of blown or residual bitumen applied hot @ 1.45kg, 1.20kg and 1.45kg per sq.m of areas respectively, second and fourth courses of roofing with felt type 3 grade - I (hessain base self finished bitumen felt) and sixth and final course with stone grit 6mm and down per sq.m including preparation of surface, excluding grading complete.

Supplying, providing, mixing and laying over waterproofing layers/ coatings with concrete screed of average 30mm thick or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with 10mm and down well graded aggregates and admixed with a normal plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 430x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and CP brass spreaders with brass unios and GI clamps complete including painting of fitting and brackets cutting and making good the walls and floors wherever required One urinal basin with 5 ltr white PVC automatic flushing cistern

Providing and fixing wash basin with CI brackets 15mm CP brass pillar taps 32mm CP brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White vitreous china wash basin size 630x450mm with a pair of 15 mm CP brass pillar taps

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 610x510 mm bowl depth 200 mm

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Supplying fitting and fixing supreme brand / Prince brand or similar approved P.V.C. Pipes of following sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. ii) PRINCE BRAND (High presure pipe Sch-40) Exposed or in trenches

15mm nominal bore

20mm nominal bore

25mm nominal bore

32mm nominal bore

40mm nominal bore

50mm nominal bore

Making connection of GI distribution branch with GI main of following sizes by providing and fixing tee including cutting and threading the pipe ect complete

25 to 40mm nominal bore

50 to 80mm nominal bore

Providing and fixing 100mm sand cast iron grating for gully trap

Providing and laying and jointing glazed stoneware pipes grade "A" with stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement 1 fine sand ) including testing of joints etc. complete

100 mm diameter

150 mm diameter

Providing and fixing square mouth SW gully trap grade :A: complete with CI grating brick masonry chamber with water tight CI cover with frame of 300x300mm size(inside) the weighing of cover to be not less than 4.50kg and frame to be not less than 2.70kg as per standard design 100x100mm size P type With FPS bricks class designation 75

Providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to IS 13592 type a including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. (i) single socketed pipes 110mm diameter

Sintex Water Tank,2000 Litres capacity

Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration rate per hour of TARUS make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six monthhs (F)REVERSE OSMOSIS (R.O)-For best Quality Drinking Water (I) KENT Grand +,15 lph,8 litres storage

Providing and laying non- pressure NP2 class (light duty) RCC pipes with collars joints with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement 2 fine sand ) including testing of joints etc, complete 150 mm dia RCC pipe

Constructing brick masonry circular type manhole 0.91mm internal dia at bottom and 0.56m dia at top in cement mortar 1:4( 1 cement 4 coarse sand ) in side cement plaster 12mm thick with cement mortar 1:3( 1 cement 3 coarse sand ) finished with a floating coat of neat cement foundation concrete 1:3:6( 1 cement 3 coarse sand 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design 0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to IS 12592 total weight of cover and frame to be not less than 182 kg, fixed in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stones aggregate 20mm nominal size) including centering shuttering all complete at the external surface shall be paid for separately) With FPS bricks with class designation 75

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels. (Cement concrete to be measured and paid separately). a)Side hung and Top hung windows and ventilators

Providing, fitting and fixing Coloured anodised aluminuim framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm lock rails 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete including hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc complete as specified and directed by the department at all levels. (i)6mm clear glass

Providing plinth protection with bricks flat laid in cement mortar 1:4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Supply & erection of MCB in existing distribution board including making connection complete with

16 Amps SPMCB

25 Amps SPMCB

40 Amps DP MCB

Call bell 220/230V with double coil

Bell Push

Supply & erection of 10.5cm dia MS Fan boxes

Supply & erection of 9W LED

Supply & erection 2x24W led tube light

Supply & erection 5w led light

Supply & erection 12w led light

Ceiling Fans,1400mm Sweep (USHA/CGL)

Exhaust Fans

Industrial Power Socket 32 Amps

Cable from ACDB to distribution board Al ( 2C x 16 sq mm)

Part F (vi) - Store room building

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.5.1) UNIFORM PILE Concrete Grade M25 500mm dia, 9.0+3.5=12.5 m long pile 23 nos

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) TMT bar made of Primary producer (From Primary producer)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using Mixer Machine

In substructure up to plinth level : - Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

In super structure from plinth level up to 1st floor level. Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in:

Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200mm in thickness.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (I) In Sub-structure upto plinth level including dewatering if necessary (d) In proportion 1:6.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (II) In superstructure above plinth level up to 1st floor level. (d) In proportion 1:6.(1 cement:6 sand)

Celling Plaster work : - 10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. (a) In cement mortar 1:3

Internal Plaster work :- 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A. On rough side (b) In cement mortar 1:4

External Plaster work with water proofing materials:- 20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. B. On fair side (backing coat 10 mm and finishing coat 10mm thick) (b) In cement mortar 1:4

Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. 100mm thick

VITRIFIED TILES A) AT FLOOR Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) Normal range (600mmx600mm and above) i) Somany Madea) Digital- Gold VC

B) AT WALL SProviding polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). Executive range- 1 (Sizes 300 mm x450mm and above) i) Somany made a) Gold

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A- Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (A) CERAMIC i)Normal range (Sizes 300 mm x 300mm and above)

Providing polished granite tiles of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

(a) Removing white or colour wash by steel wire brushing and/ or scraping, sand papering and preparing the wall surface smooth including necessary repairs to scratches complete.

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing two coats of J.K Wall Putty ( White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICIpaint/ J & N paint/ Nerolac)

Finishing old / new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats).

Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels.

Providing and laying six course water proof treatment with bitumen felt over roof consisting of first, third and fifth courses of blown or residual bitumen applied hot @ 1.45kg, 1.20kg and 1.45kg per sq.m of areas respectively, second and fourth courses of roofing with felt type 3 grade - I (hessain base self finished bitumen felt) and sixth and final course with stone grit 6mm and down per sq.m including preparation of surface, excluding grading complete.

Supplying, providing, mixing and laying over waterproofing layers/ coatings with concrete screed of average 30mm thick or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with 10mm and down well graded aggregates and admixed with a normal plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with CI brackets 15mm CP brass pillar taps 32mm CP brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White vitreous china wash basin size 630x450mm with a pair of 15 mm CP brass pillar taps

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm,weighing not less than 190 gms.

Supplying fitting and fixing supreme brand / Prince brand or similar approved P.V.C. Pipes of following sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. ii) PRINCE BRAND (High presure pipe Sch-40) Exposed or in trenches

15mm nominal bore

20mm nominal bore

25mm nominal bore

32mm nominal bore

40mm nominal bore

50mm nominal bore

Making connection of GI distribution branch with GI main of following sizes by providing and fixing tee including cutting and threading the pipe ect complete

25 to 40mm nominal bore

50 to 80mm nominal bore

Providing and fixing 100mm sand cast iron grating for gully trap

Providing and laying and jointing glazed stoneware pipes grade "A" with stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement 1 fine sand ) including testing of joints etc. complete

100 mm diameter

150 mm diameter

Providing and fixing square mouth SW gully trap grade :A: complete with CI grating brick masonry chamber with water tight CI cover with frame of 300x300mm size(inside) the weighing of cover to be not less than 4.50kg and frame to be not less than 2.70kg as per standard design 100x100mm size P type With FPS bricks class designation 75

Providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to IS 13592 type a including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. (i) single socketed pipes 110mm diameter

Sintex Water Tank,2000 Litres capacity

Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration rate per hour of TARUS make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six monthhs (F)REVERSE OSMOSIS (R.O)-For best Quality Drinking Water (I) KENT Grand +,15 lph,8 litres storage

Providing and laying non- pressure NP2 class (light duty) RCC pipes with collars joints with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement 2 fine sand ) including testing of joints etc, complete 150 mm dia RCC pipe

Constructing brick masonry circular type manhole 0.91mm internal dia at bottom and 0.56m dia at top in cement mortar 1:4( 1 cement 4 coarse sand ) in side cement plaster 12mm thick with cement mortar 1:3( 1 cement 3 coarse sand ) finished with a floating coat of neat cement foundation concrete 1:3:6( 1 cement 3 coarse sand 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design 0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to IS 12592 total weight of cover and frame to be not less than 182 kg, fixed in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stones aggregate 20mm nominal size) including centering shuttering all complete at the external surface shall be paid for separately) With FPS bricks with class designation 75

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels. (Cement concrete to be measured and paid separately). a)Side hung and Top hung windows and ventilators i)6mm clear glass

Providing, fitting and fixing Coloured anodised aluminuim framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm lock rails 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete including hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc complete as specified and directed by the department at all levels. (i)6mm clear glass

Providing plinth protection with bricks flat laid in cement mortar 1:4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Light & fan Point (First Point)

Light & fan Point (second Point)

Call bell point including MS Box of Size 180mmx100mmx60mm deep for Call bell

3 pin 6 amp plug point including earthing the 3rd pin (power Point)

3 pin 16 amp plug point including earthing the 3rd pin (power Point)

Supply & erection of PVC Copper insulated & sheathed 2 Wire circular flexible wire size 4Sq.mm(power point)

Supply & erection of PVC sheathed copper conductor cable single core 1100V grade in sizing 6Sq mm ( AC Point)

supply & errection of 25 Amp DP MCCB (AC point)

Supply & erection of sheet steel enclosure distribution board suitable for MCB,s etc on wall with rag bolts -12 Way (Three Pole) Including SPMCB 10 No 6-32A & incomer DPMCB 63 A

Supply & erection of MCB in existing distribution board including making connection complete with

16 Amps SPMCB

25 Amps SPMCB

40 Amps DP MCB

Call bell 220/230V with double coil

Bell Push

Supply & erection of 10.5cm dia MS Fan boxes

Supply & erection of 9W LED

Supply & erection 2x24W led tube light

Supply & erection 5w led light

Supply & erection 12w led light

Ceiling Fans,1400mm Sweep (USHA/CGL)

Exhaust Fans

Industrial Power Socket 32 Amps

Cable from ACDB to distribution board Al ( 2C x 16 sq mm)

Part F (vii) - Security/Guard room (2 nos.)

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.5. 1)UNIFORM PILE Concrete Grade M25 400mm dia, 9.0+3.5=12.5 m long pile 4 nos

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) TMT bar made of Primary producer (From Primary producer)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using Mixer Machine M25 grade concrete

In substructure up to plinth level :- Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level.

In super structure from plinth level up to 1st floor level. Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in:

Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200mm in thickness.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (I) In Sub-structure upto plinth level including dewatering if necessary (d) In proportion 1:6.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (II) In superstructure above plinth level up to 1st floor level. (d) In proportion 1:6.(1 cement:6 sand)

Celling Plaster work 10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed .(a) In cement mortar 1:3

Internal Plaster work 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A. On rough side (b) In cement mortar 1:4

External Plaster work with water proofing materials 20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. B. On fair side (backing coat 10 mm and finishing coat 10mm thick) (b) In cement mortar 1:4

Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. 100mm thick

VITRIFIED TILES (A) AT FLOOR Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) Normal range (600mmx600mm and above) i) Somany Made a) Digital- Gold VC

B) AT WALLS Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). Executive range- 1 (Sizes 300 mm x450mm and above) i) Somany made a) Gold

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A- Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (A) CERAMIC i)Normal range (Sizes 300 mm x 300mm and above)

Providing polished granite tiles of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department )i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

(a) Removing white or colour wash by steel wire brushing and/ or scraping, sand papering and preparing the wall surface smooth including necessary repairs to scratches complete.

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing two coats of J.K Wall Putty ( White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICIpaint/ J & N paint/ Nerolac)

Finishing old / new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats).

Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels.

Providing and laying six course water proof treatment with bitumen felt over roof consisting of first, third and fifth courses of blown or residual bitumen applied hot @ 1.45kg, 1.20kg and 1.45kg per sq.m of areas respectively, second and fourth courses of roofing with felt type 3 grade - I (hessain base self finished bitumen felt) and sixth and final course with stone grit 6mm and down per sq.m including preparation of surface, excluding grading complete.

Supplying, providing, mixing and laying over waterproofing layers/ coatings with concrete screed of average 30mm thick or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with 10mm and down well graded aggregates and admixed with a normal plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with CI brackets 15mm CP brass pillar taps 32mm CP brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White vitreous china wash basin size 630x450mm with a pair of 15 mm CP brass pillar taps

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Supplying fitting and fixing supreme brand / Prince brand or similar approved P.V.C. Pipes of following sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. ii) PRINCE BRAND (High presure pipe Sch-40) Exposed or in trenches

15mm nominal bore

32mm nominal bore

Making connection of GI distribution branch with GI main of following sizes by providing and fixing tee including cutting and threading the pipe ect complete 25 to 40mm nominal bore

Providing and fixing 100mm sand cast iron grating for gully trap

Providing and laying and jointing glazed stoneware pipes grade "A" with stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement 1 fine sand ) including testing of joints etc. complete

100 mm diameter

150 mm diameter

Providing and fixing square mouth SW gully trap grade :A: complete with CI grating brick masonry chamber with water tight CI cover with frame of 300x300mm size(inside) the weighing of cover to be not less than 4.50kg and frame to be not less than 2.70kg as per standard design 100x100mm size P type With FPS bricks class designation 75

Providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to IS 13592 type a including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. i) single socketed pipes 110mm diameter

Sintex Water Tank,2000 Litres capacity

Providing and laying non- pressure NP2 class (light duty) RCC pipes with collars joints with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement 2 fine sand ) including testing of joints etc, complete 150 mm dia RCC pipe

Constructing brick masonry circular type manhole 0.91mm internal dia at bottom and 0.56m dia at top in cement mortar 1:4( 1 cement 4 coarse sand ) in side cement plaster 12mm thick with cement mortar 1:3( 1 cement 3 coarse sand ) finished with a floating coat of neat cement foundation concrete 1:3:6( 1 cement 3 coarse sand 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design 0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to IS 12592 total weight of cover and frame to be not less than 182 kg, fixed in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stones aggregate 20mm nominal size) including centering shuttering all complete at the external surface shall be paid for separately) With FPS bricks with class designation 75

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels. (Cement concrete to be measured and paid separately). a)Side hung and Top hung windows and ventilators i) 6 mm clear glass

Providing, fitting and fixing Coloured anodised aluminuim framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm lock rails 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete including hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc complete as specified and directed by the department at all levels. (i)6mm clear glass

Providing plinth protection with bricks flat laid in cement mortar 1:4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Light & fan Point (First Point)

Light & fan Point (second Point)

Call bell point including MS Box of Size 180mmx100mmx60mm deep for Call bell

3 pin 6 amp plug point including earthing the 3rd pin (power Point)

3 pin 16 amp plug point including earthing the 3rd pin (power Point)

Supply & erection of PVC Copper insulated & sheathed 2 Wire circular flexible wire size 4Sq.mm(power point)

Supply & erection of sheet steel enclosure distribution board suitable for MCB,s etc on wall with rag bolts -12 Way (Three Pole) Including SPMCB 10 No 6-32A & incomer DPMCB 63 A

Supply & erection of MCB in existing distribution board including making connection complete with

16 Amps SPMCB

25 Amps SPMCB

40 Amps DP MCB

Bell Push

Supply & erection of 10.5cm dia MS Fan boxes

Supply & erection of 9W LED

Supply & erection 2x24W led tube light

Supply & erection 5w led light

Ceiling Fans,1400mm Sweep (USHA/CGL)

Exhaust Fans

Industrial Power Socket 32 Amps

Cable from ACDB to distribution board Al ( 2C x 16 sq mm)

Part F (viii) - Transit camp building

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as (A) Up to a depth of 2.00m below the existing ground level.directed and specified. (a) In ordinary soil.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.5.1) UNIFORM PILE Concrete Grade M25

Pile dia 400 mm, 9.0+3.5=12.5m long pile 15 nos

Pile dia 500 mm, 9.0+3.5=12.5m long pile 45 nos

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) TMT bar made of Primary producer (From Primary producer)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using Mixer Machine

In substructure up to plinth level: - Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

In super structure from plinth level up to 1st floor level.: -Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200mm in thickness.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (I) In Sub-structure upto plinth level including dewatering if necessary (d) In proportion 1:6.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.zz (II) In superstructure above plinth level up to 1st floor level. (d) In proportion 1:6.(1 cement:6 sand)

Celling Plaster work : -10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. (a) In cement mortar 1:3

Internal Plaster work :- 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A. On rough side (b) In cement mortar 1:4

External Plaster work with water proofing materials:- 20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. B. On fair side (backing coat 10 mm and finishing coat 10mm thick) (b) In cement mortar 1:4

Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. 100mm thick

VITRIFIED TILES (A) AT FLOOR Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) Normal range (600mmx600mm and above) i) Somany Made a) Digital- Gold VC

B) AT WALLS Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). Executive range- 1 (Sizes 300 mm x450mm and above) i) Somany made a) Gold

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (A) CERAMIC i)Normal range (Sizes 300 mm x 300mm and above)

Providing polished granite tiles of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

(a) Removing white or colour wash by steel wire brushing and/ or scraping, sand papering and preparing the wall surface smooth including necessary repairs to scratches complete.

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing two coats of J.K Wall Putty ( White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Finishing old / new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats).

Preparing the RCC surface in roof slab, chajjas, terraces, sunken slabs, septic tank, OH tank, raft slab, walls etc. by thoroughly cleaning with wire brush etc. followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc. and allowing surface to dry complete as directed at all levels.

Providing and laying six course water proof treatment with bitumen felt over roof consisting of first, third and fifth courses of blown or residual bitumen applied hot @ 1.45kg, 1.20kg and 1.45kg per sq.m of areas respectively, second and fourth courses of roofing with felt type 3 grade- I (hessain base self finished bitumen felt) and sixth and final course with stone grit 6mm and down per sq.m including preparation of surface, excluding grading complete.

Supplying, providing, mixing and laying over waterproofing layers/ coatings with concrete screed of average 30mm thick or as per drawings/ requirements in proportion 1:2:4 (1cement : 2fine aggregate : 4coarse aggregate) (by volume) with 10mm and down well graded aggregates and admixed with a normal plasticizer like Master Plast PL-1 of Choksey Chemicals /Dr. Sealkit Normal Plast (Asian Chemicals)/Rheomac 707 of BASF @ 0.3% by weight of cement and thereafter scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department.

Providing and fixing water closet squatting pan(indian type WC pan) with 100mm sand cast iron P or S trap 10 ltr low level white PVC flushing cistern with manually controlled device (handle level) conforming to IS 7231 with all fitting and fixtures complete including cutting and making good the walls and floors wherever required White vitreous china orissa pattern WC pan of size 580x440mm with integral type foor rests

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 430x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and CP brass spreaders with brass unios and GI clamps complete including painting of fitting and brackets cutting and making good the walls and floors wherever required One urinal basin with 5 ltr white PVC automatic flushing cistern

Providing and fixing wash basin with CI brackets 15mm CP brass pillar taps 32mm CP brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require White vitreous china wash basin size 630x450mm with a pair of 15 mm CP brass pillar taps

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 610x510 mm bowl depth 200 mm

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Supplying fitting and fixing supreme brand / Prince brand or similar approved P.V.C. Pipes of following sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. ii) PRINCE BRAND (High presure pipe Sch-40) Exposed or in trenches

15mm nominal bore

20mm nominal bore

25mm nominal bore

32mm nominal bore

40mm nominal bore

50mm nominal bore

Making connection of GI distribution branch with GI main of following sizes by providing and fixing tee including cutting and threading the pipe ect complete

25 to 40mm nominal bore

50 to 80mm nominal bore

Providing and fixing 100mm sand cast iron grating for gully trap

Providing and laying and jointing glazed stoneware pipes grade "A" with stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement 1 fine sand ) including testing of joints etc. complete

100 mm diameter

150 mm diameter

Providing and fixing square mouth SW gully trap grade :A: complete with CI grating brick masonry chamber with water tight CI cover with frame of 300x300mm size(inside) the weighing of cover to be not less than 4.50kg and frame to be not less than 2.70kg as per standard design 100x100mm size P type With FPS bricks class designation 75

Providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to IS 13592 type a including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. (i) single socketed pipes 110mm diameter

Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration rate per hour of TARUS make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six monthhs (F)REVERSE OSMOSIS (R.O)-For best Quality Drinking Water (I) KENT Grand +,15 lph,8 litres storage

Sintex Water Tank,2000 Litres capacity

Providing and laying non- pressure NP2 class (light duty) RCC pipes with collars joints with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement 2 fine sand ) including testing of joints etc, complete 150 mm dia RCC pipe

Constructing brick masonry circular type manhole 0.91mm internal dia at bottom and 0.56m dia at top in cement mortar 1:4( 1 cement 4 coarse sand ) in side cement plaster 12mm thick with cement mortar 1:3( 1 cement 3 coarse sand ) finished with a floating coat of neat cement foundation concrete 1:3:6( 1 cement 3 coarse sand 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design 0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to IS 12592 total weight of cover and frame to be not less than 182 kg, fixed in cement concrete 1:2:4( 1 cement 2 coarse sand 4 graded stones aggregate 20mm nominal size) including centering shuttering all complete at the external surface shall be paid for separately) With FPS bricks with class designation 75

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels. (Cement concrete to be measured and paid separately). a)Side hung and Top hung windows and ventilators i) 6 mm clear glass

Providing, fitting and fixing Coloured anodised aluminuim framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm lock rails 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete including hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc complete as specified and directed by the department at all levels. (i)6mm clear glass

Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Light & fan Point (First Point)

Light & fan Point (second Point)

Call bell point including MS Box of Size 180mmx100mmx60mm deep for Call bell

3 pin 6 amp plug point including earthing the 3rd pin (power Point)

3 pin 16 amp plug point including earthing the 3rd pin (power Point)

Supply & erection of PVC Copper insulated & sheathed 2 Wire circular flexible wire size 4 Sq.mm(power point)

Supply & erection of PVC sheathed copper conductor cable single core 1100V grade in sizing 6Sq mm ( AC Point)

supply & errection of 25 Amp DP MCCB (AC point)

Supply & erection of sheet steel enclosure distribution board suitable for MCB,s etc on wall with rag bolts -12 Way (Three Pole) Including SPMCB 10 No 6-32A & incomer DPMCB 63 A

Supply & erection of MCCB on wall or on pedestal including bonding to earth & necessary connections-200Amp,415 V ,3phase

Supply & erection of MCB in existing distribution board including making connection complete with

16 Amps SPMCB

25 Amps SPMCB

40 Amps DP MCB

63 Amps FPMCB

Call bell 220/230V with double coil

Bell Push

Supply & erection of 10.5cm dia MS Fan boxes

Supply & erection of 9W LED

Supply & erection 2x24W led tube light

Supply & erection 5w led light

Supply & erection 12w led light

Ceiling Fans,1400mm Sweep (USHA/CGL)

Exhaust Fans

Industrial Power Socket 32 Amps

Cable from ACDB to distribution board Al ( 4C x 35 sq mm)

Part G (i) - Tower foundations

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.5.1) UNIFORM PILE Concrete Grade M25

Pile dia 400 mm, 11.0+3.5=14.50m long pile 84nos

Pile dia 500 mm, 12.0+3.5=15.5m long pile 140nos

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) TMT bar made of Primary producer (From Primary producer)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1 cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works using cement, coarse sand & 20mm down graded stone aggregate with cost of necessary form work including dewatering if necessary, and curing for reinforced cement concrete work complete as directed (Reinforcement will be measured and paid separately) Using mixture machine

In sub - structure up to plinth level : Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Part G (ii) - Equipment foundations

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1 cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works using cement, coarse sand & 20mm down graded stone aggregate with cost of necessary form work including dewatering if necessary, and curing for reinforced cement concrete work complete as directed (Reinforcement will be measured and paid separately) Using mixture machine In sub - structure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Part G (iii)-50 MVA Power Transformer foundation

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.5.1) UNIFORM PILE Concrete Grade M25 Pile dia 400 mm 9.0+3.5=12.5m long pile 28 nos

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) TMT bar made of Primary producer (From Primary producer)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1 cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works using cement, coarse sand & 20mm down graded stone aggregate with cost of necessary form work including dewatering if necessary, and curing for reinforced cement concrete work complete as directed (Reinforcement will be measured and paid separately) Using mixture machine In sub - structure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Structure Steel Structural steel work in sigle sections including cutting, hoisting, fixing in position and applying a priming coat of red lead paint (up to 4.6m height) from plinth level including drilling holes, supplying, fitting and fixing with bolts and nuts or welding, if necessary as directed. c) In M.S. angles, channels, Tees etc.

Part G (iv) - Station Transformer foundation

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1 cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works using cement, coarse sand & 20mm down graded stone aggregate with cost of necessary form work including dewatering if necessary, and curing for reinforced cement concrete work complete as directed (Reinforcement will be measured and paid separately) Using mixture machine In sub - structure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code fo rR.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Structure Steel Structural steel work in sigle sections including cutting, hoisting, fixing in position and applying a priming coat of red lead paint (up to 4.6m height) from plinth level including drilling holes, supplying, fitting and fixing with bolts and nuts or welding, if necessary as directed. c) In M.S. angles, channels, Tees etc.

Part G (v) - Burnt Oil Tank

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.5.1) UNIFORM PILE Concrete Grade M25 Pile dia 400 mm 9.0+3.0=12.0m long pile 16nos

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor...etc) TMT bar made of Primary producer (From Primary producer)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1 cement: 4 sand :8 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works using cement, coarse sand & 20mm down graded stone aggregate with cost of necessary form work including dewatering if necessary, and curing for reinforced cement concrete work complete as directed (Reinforcement will be measured and paid separately) Using mixture machine In sub - structure up to plinth level:-Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Part H - Landscaping work

TREE PLANTING Supplying and planting of ornamental trees (1'-0" height sapling) including pit making ( 60 cm x 60 cm x 60 cm ), filling the pit with appropriate soil media, manure and fertilizers as per specification and necessary maintenance for a period of one year from the date of planting complete as specified and directed . SHADE TREE (D) Bottle Brush / Nil Gulmohar / Debadaru / Weeping Willow

HEDGE PLANTING / EXTERNAL HEDGE Supplying and planting of suitable plant materials for preparation protective / external hedge (50 cm wide) including the preparation of the ground by mixing organic manure and fertilizers as per specification and necessary maintenance for a period of one year from the date of planting complete as specified and directed. (B) ADOPTING CROSS WISE DOUBLE ROW PLANTING METHOD (iii) With Chinese Bamboo

EDGE PLANTING / INTERNAL HEDGE: Supplying and planting of suitable plant materials for edge making / Internal hedge(20 cm wide) including the preparation of the ground by mixing organic manure and fertilizers as per specification and necessary maintenance for a period of one year from the date of planting complete as specified and directed. (B) ADOPTING CROSS WISE DOUBLE ROW PLANTING METHOD (iii) With Brindavan / Latifolius

SHRUB PLANTING : Supplying and planting of ornamental shrub ( below 1'-0" height ) including pit making ( 60 cm x 60 cm x 60 cm ), filling the pit with appropriate soil media, manure and fertilizers as per specification and necessary maintenance for a period of one year from the date of planting complete as specified and directed. (A) Radhachura / Krishnachura / Rat ki rani / Ixora / Jetuka

Part I - Water Supply work

Supply and installation of Deep tubewell, with appropriate depth required to reach aquifer with PVC casing pipe (200 mm diameter minimum), 2 HP submersible mortor pump, 40 mm diameter CPVC column pipe, one unit RCC Slow Sand Filter (Capacity 10,000 Ltr/hr) along with RCC ground storage tank (Capacity 25,000 Ltr/hr) Supply and Installation of distribution network with uPVC pipe of 40 mm diameter and 25 mm diameter for connecting to Overhead tank.

Part J - Car Parking

Construction of Shed for car parking at different locations with each unit for single car parking of minimum size 5.5m x 3 m with a plinth height of minimum 300 mm. The floor should be completed with pavers block with appropriate base, which has to be joined with the approach or internal road. Construction of shed structure using Steel section by TATA of YST 310 Grade with RCC block as base. Shed roofing to be completed with PPGI sheet roofing with minimum 0.6 mm thickness. (Design and Drawing to be prepared by Contractor and shall be approved by AEGCL)

Control Room Building

Transit Camp

R.E Quarter

Officer's Hostel

Staff Hostel

Security Barrack

SALASAR TECHNO ENGINEERING LIMITED

Shyama Power India Limited

T N T Projects Ltd

Siddhartha Engineering Limited

Shyam Steel Industries Ltd.

Neccon Power and Infra Limited

Ms HEMEN DEKA

Techno Power Enterprises Private Limited

SALASAR TECHNO ENGINEERING LIMITED

Techno Power Enterprises Private Limited

Siddhartha Engineering Limited

Neccon Power and Infra Limited

M/s. ASHOKA BUILDCON LTD

T N T Projects Ltd

Shyama Power India Limited

Shyam Steel Industries Ltd.

Techno Power Enterprises Private Limited

M/s. ASHOKA BUILDCON LTD

Ms HEMEN DEKA

Shyam Steel Industries Ltd.

Siddhartha Engineering Limited

Shyama Power India Limited

T N T Projects Ltd

Neccon Power and Infra Limited

Techno Power Enterprises Private Limited

Ms HEMEN DEKA

T N T Projects Ltd

SALASAR TECHNO ENGINEERING LIMITED

Neccon Power and Infra Limited

M/s. ASHOKA BUILDCON LTD

Shyama Power India Limited

Siddhartha Engineering Limited

SALASAR TECHNO ENGINEERING LIMITED

Neccon Power and Infra Limited

Siddhartha Engineering Limited

Shyama Power India Limited

Techno Power Enterprises Private Limited

Shyam Steel Industries Ltd.

T N T Projects Ltd

M/s. ASHOKA BUILDCON LTD

Shyam Steel Industries Ltd.

Siddhartha Engineering Limited

Ms HEMEN DEKA

Techno Power Enterprises Private Limited

SALASAR TECHNO ENGINEERING LIMITED

T N T Projects Ltd

Neccon Power and Infra Limited

Shyama Power India Limited

SALASAR TECHNO ENGINEERING LIMITED

Siddhartha Engineering Limited

Shyam Steel Industries Ltd.

M/s. ASHOKA BUILDCON LTD

Ms HEMEN DEKA

Shyama Power India Limited

Techno Power Enterprises Private Limited

Neccon Power and Infra Limited