Construction of Gorkha Bhawan and Cultural Research Centre at Chirang District under SDP to be funded by Govt. of Assam. (TN_52_1)

Amount

EARTH WORKS 2.6.1. Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil.

2.25. Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. In layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

2.26. Extra for every additional of 1.5 m or part thereof in excavation / banking excavated or stacked materials.All kinds of soil BELOW GROUND 1.5 TO 3.0 M

1.1.2. Carriage of material by mechanical transport including loading, unloading to 5km.

2.35.3. Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement: 2 Coarse sand) to match the existing floor: 2.35.3.1. With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

4.1. Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 4.1.2. 1:1.5:3 (1 Cement: 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

4.1.8. 1:4:8 (1 Cement : 4 coarse sand (zone-III): 8 graded stone aggregate 40 mm nominal size)

4.17. Making plinth protection 50mm thick of cement concrete 1:3:6(1 cement :3 coarse sand: 6graded stone aggregate 20mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

Reinforced Cement Concrete Works 5.9.Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1. Foundations, footings, bases of columns, etc. for mass concrete.

5.9.2. Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3. Suspended floors, roofs, landings, balconies and access platform.

5.9.4. Shelves (Cast in situ)

5.9.5. Lintels, beams, plinth beams, girders, bressumers and cantilevers

5.9.6. Columns, Pillars, Piers, Abutments, Posts and Struts.

5.9.7. Stairs, (excluding landings) except spiral-staircases.

5.9.16. Edges of slabs and breaks in floors and walls 5.9.16.1. Under 20 cm wide

5.9.19. Weather shade, Chajjas, corbels etc., including edges

5.22.6. Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 5.22A.6. Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo- Mechanically Treated bars of grade Fe-500D or more.

5.33. Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re- design the mix or bear the cost of extra cement. 5.33.1.1. All works above plinth level upto floor V level. Concrete of M25 grade with minimum cement content of 330 kg/cum

5.33.1.2. Concrete of M30 grade with minimum cement content of 350 kg /cum

5.33.2.1. All works above plinth level upto floor V level. Concrete of M25 grade with minimum cement content of 330 kg/cum

5.33.2.2. Concrete of M30 grade with minimum cement content of 350 kg /cum

5.35. Add for using extra cement in the items of design mix over and above the specified cement content therein.

DSR-5.18.2. Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 40 mm Thick

BRICK WORK 6.1.2. Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement: 6 coarse sand)

6.4.2. Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement: 6 coarse sand)

6.13.1. Half brick masonry with common burnt clay (non modular) bricks of class- 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand)

6.15. Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

AR(DSR) C/O Apron drain of width 150mm and depth as per required of site but minimum 150 mm with neat finish & required slope as per apporoved by E/I.

MARBLE & GRANITE WORK 8.2. Providing and fixing 18mm thick gang saw cut,mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement: 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. 8.2.2. Granite of any colour and shade 8.2.2.2. Area of slab over 0.50 Sqm.

8.4. Extra for fixing marble/granite stone over and above corresponding basic item, in facia and drops of width upto 150mm with epoxy resin baesd adhesive including cleaning etc. complete.

8.5. Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/Stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edge etc. complete.

WOOD & PVC WORK DSR-9.97. Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: DSR-9.97.2. 250x10 mm

DSR-9.100. Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: DSR-9.100.1. 125 mm

DSR-9.101. Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic) coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. DSR-9.101.1. Single rubber stopper

DSR-9.103. Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS: 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

STEEL WORK 1.25 Steel work welded in built up sections/framed work, including cutting, hoisting, fitting in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.1. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

DSR-10.29. Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. 10.29.2. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

CLADDING WORK 8.9. Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete 8.9.1. 8 mm thick 8.9.1.2. Granite of any colour and shade

DSR-11.31. Extra for pre finished nosing to treads of steps of kota stone.

DSR-11.32. Extra for kota stone flooring in treads of steps and risers using single length up to 2.00 metre.

11.26. Kota stone in flooring 20 mm thick and joint filled 1:2 cement and coarse sand with approved colouring materials to be given and even shade with 12 mm base coat (bedding) of 1:4 cement and coarse sand mortar and polished by hand or machine and finally finished with french manson polish or other approved polish including supply of all materials, labour T & P etc. requird for proper completion of the work excluding base concrete. 11.26.1. 25 mm thick

11.27. Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

11.39. Providing and laying antískid rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

11.41. Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete. 11.41.2. Size of Tile 600x600 mm

11.46. Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to L.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. 11.46.2. Size of Tile 600x600 mm

11.56.1. Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

16.90. Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement: 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

ROOFING 12.21.1. Providing and laying gola 75x75mm in cement concrete M15 grade including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design in 75x75 mm deep chase.

12.22. Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement: 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

12.31. Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately). 12.31.1. Flat surfaces

12.31.2. Curved surfaces

12.45. Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.l. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making 12.45.1. painting with: openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part 1): 2011 (Board with BIS certification marks)

FINISHING WORK 13.4.2. 12 mm cement plaster of mix: 1:6 (1 cement: 6 coarse sand) ON INNER SURFACE

13.5.2. 15 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering upto floor two level including internal rounded angles not exceeding 80mm in girth and finished even and smooth (1) 1 cement: (iii) 1 cement: 6 coarse sand A. OM TO 10 M

DSR=13.22. Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. B. 10 M TO 13 M

C. 13 M TO 16 M

D. 16 M TO 19 M

13.16. 6 mm cement plaster of mix: 13.16.1. 1:3 (1 cement: 3 fine sand)

13.45. Finishing walls with textured exterior paint of required shade: 13.45.1. Finishing walls with textured exterior paint of required shade: New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

13.61. Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: 13.61.1. Two or more coats on new work

13.80. Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

DSR-13.83 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. DSR-13.83.2 Two coats

ALUMINIUM WORK DSR-21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed echanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer- in-charge. Glazing and paneling to be paid for separately): DSR-21.1.1 For fixed portion. DSR-21.1.1.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Mininum anodic coating of grade AC 15)

DSR-21.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) DSR-21.1.2.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

DSR-21.2. Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade 1 Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge. DSR-21.2.1. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

DSR-21.3. Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): DSR-21.3.2. With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

DSR-21.4. Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body/ plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. DSR-21.4.1. With stainless steel cover plate minimum 1.25 mm thickness

DSR-21.8. Filling the gap in between aluminium frame and adjacent RCC/Brickwork/ Stone Work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge DSR-21.8.1. Upto 5mm depth and 5mm width

WATER PROFFING 1st course of applying cement slurry @ 4.4 Kg/Sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off Junction of vertical and horizontal surface. (il) lind course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) Illrd course of applying blown or residual bitumen applied hot at 1.7 Kg. per Sqm of area. (lv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/Sqm.)

Supplying and Stacking Filling sunken floor with over burnt jhama brick aggregate 90mm to 45mm including compacting of materials complete as specified and directed for all levels.

22.7. Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terracesetc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cernent admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge.. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1.4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. SUB HEAD: 22-WATER PROOFING 1548 (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test."All above operations to be done in order and as directed and specified by the Engineer-in-Charge: 22.7.1. With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

22.24. Providing and applying integral crystalline (dry shake) of hydrophilic in nature for waterproofing treatment to the RCC structures like basement raft, foundation slab, sewage & water treatment plant slab, warehouses floor, parking structures and water tank base slab etc. sprinkled @0.60kg per sqm or higher as recommended by the manufacturer's specification over the lean concrete of above cited structures. The material shall meet the requirements as specified in ACI-212-3R-2010 l.e. by reducing permeability of concrete by more than 85% , compared control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dryshake shall be capable of self healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The productperformance shall carry guarantee for 10 years against any leakage.

INTERNAL PLUMBING WORKS 17.2. Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS: 7231, Parryware/ Hindware/ Seabrid /Orient (Coral) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : 17.2.2. W.C. pan with ISI marked black solid plastic seat and lid

17.7.1. a)White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

17.28. Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 17.28.1. Semi rigid pipe 17.28.1.1. 32 mm dia

17.31. Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

CP Brass fittings 18.21. Providing and fixing unplasticised PVC connection pipe with brass unions 18.21.2. 45 cm length 15 mm nominal bore

17.16.A. Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean & Wall moutain type W.C. of quality and make as approved by Engineer - in - charge.

18.49. Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 18.49.1. a) 15 mm nominal bore

18.53. Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS:8931 18.53.1. a) 15 mm nominal bore

17.22A. Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

17.71. Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

17.73. Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.1. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing & fixing soil, waste and vent pipes. 17.35.1.2. a) 100mm dia centrifugally cast iron S & S pipe.

17.35.2.2. b) 75mm dia centrifugally cast iron S & S pipe.

18.10. Providing and fixing GI pipes complete with GI fittings and clamps, including cutting and making good walls etc. (for wash basin waste ) 18.10.4. 32mm dia nominal bore

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes & fitting of diameters. 17.58.1. a) 100mm

Providing & fixing M.S. holder bat clamps of approved design to sand cast iron/centrifugally cast (Spun) iron S & S pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4 mix (1 cement: 2 coarse: 4 graded stone aggregate 20mm nominal size). Including cost of cutting holes & making good the walls etc. 17.37.1. a) for 100mm dia pipe.

17.37.2. b) for 75mm dia pipe.

Providing & fixing cast iron coller. 17.57.1.2. a) 100mm dia.

17.57.2.2. b) 75mm dia.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 17.60.1.1. a) 100mm inlet & 100mm outlet.

17.60.2.1. a) 100mm inlet & 75mm outlet.

Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. 17.38.1.2. a) 100mm

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 17.43.1.2. 100x100x100mm

Providing and fixing centrifugaly cast iron single equal plain junction of required degree. 17.44.1.2. 100x100x100mm

Providing and fixing single unequal junction of required degree with access door, Insertion rubber washer 3 mm thick, bolts and nuts complete: 17.47.1.2. 100x100x75mm

Providing and fixing single unequal plain invert branch of required degree: 17.52.1.2. 100x100x75mm

Providing and fixing door plece, insertion rubber washer 3mm thick, bolts & nuts complete :( c.o.p.) 17.55.1.2. a) 100mm

Providing and fixing cast iron terminal guard. 17.56.1.2. 100 mm

19.2.1. Providing and laying cement concrete 1:5:10(1 cement : 5 coarse sand : 10 graded stone aggregate 20mm nominal size) around P.V.C Soil and waste pipe including bed concrete as per standard design(embedded in the flooring / ground) 110 mm dia

12.42. Providing and fixing on wall face unplasticised PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion. 12.42.5.2. Bend 87.5 degree 12.42.5.2. 110 mm Bend

12.42.6. Shoe (Plain) 12.42.6.2. 110 mm Shoe

12.44. Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

12.43. Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with MS screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 12.43.2. 110 mm

12.22. Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 18.8.2. 20mm dia nominal outer dia pipes

18.8.3. 25mm dia nominal outer dia pipes

18.8.4. 32mm dia nominal outer dia pipes

Providing and fixing GI pipes complete with GI fittings and clamps, including cutting and making good walls etc. (internal works) 18.10.1. 15mm dia nominal bore

18.10.2. 20mm dia nominal bore

18.10.3. 25mm dia nominal bore

18.10.4. 32mm dia nominal bore

18.10.5. 40mm dia nominal bore

18.10.6. 50mm dia nominal bore

Terrace and external work 18.12.7. 65mm dia nominal bore

18.12.8. 80mm dia nominal bore

Painting GI pipes and fittings with SYNTHETIC enamel paint over a ready mixed priming coat, both of approved quality for new work. 18.38.1. 15mm dia nominal bore

18.38.2. 20mm dia nominal bore

18.38.3. 25mm dia nominal bore

18.38.4. 32mm dia nominal bore

18.38.5. 40mm dia nominal bore

18.38.6. 50mm dia nominal bore

Terrace and external work 18.40.7. 65mm dia nominal bore

18.40.8. 80mm dia nominal bore

Providing and fixing GI Union in GI pipes including cutting and threading the pipe and making long screws etc. complete (new work). 18.46.1. 15mm dia nominal bore

18.46.2. 20mm dia nominal bore

18.46.3. 25mm dia nominal bore

18.46.4. 32mm dia nominal bore

18.46.5. 40mm dia nominal bore

18.46.6. 50mm dia nominal bore

18.46.7. 65mm dia nominal bore

18.46.8. 80mm dia nominal bore

18.17. Providing and fixing gun metal gate valve with wheel of approved quality. 18.17.1A. 20mm dia nominal bore

18.17.1. 25mm dia nominal bore

18.17.2. 32mm dia nominal bore

18.17.3. 40mm dia nominal bore

18.17.4. 50mm dia nominal bore

18.17.5. 65mm dia nominal bore

18.17.6. 80mm dia nominal bore

18.18. Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 18.18.3. 25 mm nominal bore

2.10 Excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in ramming, watering etc. and disposing of surplus excavated soil as directed, within a lead of 50m. 2.10.1 All kind of Soil. 2.10.1.2. Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm.

19.1.Providing, laying and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. 19.1.1. 100mm diameter

19.2.Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all round S.W. pipes including bed concrete as per standard design 19.2.1. 100mm dia SW pipe

19.6. Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. 19.6.2. 150 mm. dia. RCC Pipes

19.3. Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design 19.3.2. 150 mm. dia. RCC Pipes

19.4. Providing and fixing square-mouth S.W. gully trap grade‘A’ complete with C.I. grating, brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 19.4.2. 150 x 100 mm size P type 19.4.2.2. With Sewer bricks conforming to IS : 4885

19.7. Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design. 19.7.1. Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). 19.7.1.1. With FPS bricks of class designation 75 (i) For Sewer Line

19.15. Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement:3 coarse sand :6graded stone aggregate 20 mm nominal size) as per standard design 19.15.1. With 20x20 mm square bar

Supply installation, testing and commissioning of recessed bi level drinking water fountain, with double SS bubbler. Drinking water fountain with 8GPH cooling capacity, stainless steel body ,approx size 1003mmX Depth 400 mmX hight 1035mm, SS bubbler guard operated between 50 to 120 PSI, ,with MDCU29 antimicrobial touch part, with water ways are lead free matterial chilling unit suitable for R134a refrigerant, adjustable thermo state, Green building, GRIHA,TUV And NSF Certifide, supply complete with all accessories with 100 micron stainer, Model- M8CRY-Oasis- Mechanical + Sensor Both Operation

External Plumbing Work Sewerage & Drainage System Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m All kinds of soil DSR-2.10.1.2. Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design: DSR-19.2.2. 150 mm diameter S.W. pipe

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : DSR-19.1.2. 150 mm diameter

DSR-19.4. Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: DSR-19.4.2. 150 x 100 mm size P type DSR-19.4.2.1. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : DSR-19.7.1.1. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : DSR-19.27.1. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR-19.6. Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : DSR-19.6.2. 150 mm diameter

DSR-19.16. Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

DSR-23.1. Boring/ Drilling bore well of required dia for casing strainer pipe by sutable method prescribed in IS 2800(Part I), Inculding collecting samples from different strata, preparing and submitting strata chart/bore log, Including hire & running charges of all equipments, tools , plants & machineries required for the job, all complete as per direction of engineer-in- charge , upto 90 metre depth below ground level DSR-23.1.1. All type of soil DSR-23.1.1.1. 300mm dia

DSR-23.1.2. Rocky stratra including boulders 300 dia DSR-23.1.2.1. 300mm dia

DSR-23.3. Supplying , assembling, lowering and fixing in vertical postion in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS 12818, including required hire and labour charges, fitting & accessories etc.all complete for all depths as per direction of engineer-in-charge . DSR-23.3.2. 150mm dia nominal size dia

DSR-23.4. Supplying .assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well.screen (RMS) pipes with ribs, conforming to IS. 12818, including hire & labour charges, fittings & accessories etc. all complete for all depths as per direction of engineer-in-charge. 150mm noninal size dia. DSR-23.4.2. 150mm dia nominal size dia

DSR-23.5. Supply, filling, spreading & leveling stone boulders of size range 5cm to 20cm, in recharge pit, thickness, for all leads and lifts, all complete as per direction Engineer in charge.

DSR-23.8. Gravel packing in tube well construction in accordance with IS 4097, including providing graval fine/medium coarse, in required grading & sizes as per actual requirement , all complete as per direction of engineer-in charge.

DSR-2.25. Filling available excavated earth ( Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and water. Lead up to 50 m and lift uoto 1.5 m.

DSR-2.26.1. Extra for every addition lift of 1.5 m or part thereof in excavation/ banking excavated or stacked materials. All kinds of soil.

DSR-19.19.3.1. Providing and fixing in position pre-cast RCC manhole covers and frame of required shape and approved quality H D - 20 Circular shape 560 mm internal diameter

DSR-23.13. Providing and fixing suitable size threaded mild steel cap or shot welded plate to the top of borewell housing chasing pipe as per removable as per requirement, all complete for borewell of: DSR-23.13.3. 200mm dia

DSR-23.15. Providing and fixing Bail plug/Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (Part-I) . DSR-23.15.2. 150mm dia

DSR-19.16. Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS:10910, on 12mm dia steel bar conforming to IS: 1786, having minimum cross section as 23mm X 25mm and over all minimum length 263mm and width as 165mm with minimum 112 mm space between protruded legs having 2mm tread on top surface by ribbing or chequiring besides necessary and adequate anchoring projection on tail length on 138mm as per standard drawing and suitable to with stand the bend test and chemical resistance identification mark to be visible even after fixing,including fixing manhole with 30X20X15cm cement concrete block 1:3:6(1 cement: 3 Coarse sand: 6 graded stone aggregrate 20mm nominal size) complete as per design

DSR-19.7.2.1. Constructing brick masonry manhole (silt chamber type) inside size 1.20X0.90c 1.20m deep with FPS brick class designation 75 in cement mortar 1:4 (1 Cement: 4 coarse sand ) 15mm thick RCC top slab with 500mm dia opening in cement concrete 1:2:4 (1 cement: 2 C/sand: 4 graded stone agg, n/size reinforced with 18.92 kg cold twisted sreel bars 20cm foundation concrete 1:4:8 (1 cement: 4 C/sand: 8 graded stone agg 40mm size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 C/sand) finished with a foating coat of neat cement and providing 75 mm thick bed concrete in 1:2:4 mix (1 cement: 2 C/sand: 4 graded stoneagg . 20mm n/size) including neat cement punning inside the manhole complete as per standard design/depth shall be measured from invert level of manhole excluding cost of manhole cover and frame which shall be paid for separately etc. All complete as per direction of engineer-in-charge.

DSR-19.8.2.1. Extra for depth for manhole size ( 120cmx90cm) with common burnt clay F.P.S ( non- modular) bricks of class designation 7.5

DSR-1.1.2. Carriage of Material by mechanical transport including loading ,unloading etc. Complete lead 1 km the place of disposal shall be approved by the engineer-in- charge

DSR-4.1.10. Providing and laying in position cement concrete of specificed grade excluding the cost of centering and shuttering - All work upto plinth level 1:5:10 (1 Cement: 5 coarse sand: 10 graded stone aggregate 40mm niminal size)

DSR-4.1.3. Providing and laying in position cement concrete of specificed grade excluding the cost of centering and shuttering - All work upto plinth level 1:2:4 (1 Cement: 2 coarse sand: 4 graded stone aggregate 20mm niminal size)

BOREWELL 23.1 Boring/drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS:2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer - in-charge, upto 90 metre depth below ground level. DSR-23.1.2. Rocky strata including Boulders DSR-23.1.2.1. 300mm dia

DSR-23.2. Boring/drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS:2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer - in-charge, upto 90 metre depth below ground level. DSR-23.2.2. Rocky strata including Boulders DSR-23.2.2.1. 300mm dia

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work DSR-18.12.7. 65 mm dia. nominal bore

DSR-23.3. Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. DSR-23.3.2. 150 mm nominal size dia

DSR-23.4. Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs conforming to IS: 12818, including hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. DSR-23.4.2. 150 mm nominal size dia

DSR-23.8. Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer- in -charge.

DSR-23.12. Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

DSR-23.13. Providing and fixing suitable size threaded mild steel cap or shot welded plate to the top of borewell housing chasing pipe as per removable as per requirement, all complete for borewell of: DSR-23.13.3. 200mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. DSR-23.14.2. 150 mm clamp

DSR-23.15. Providing and fixing Bail plug/Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (Part-I) . DSR-23.15.2. 150mm dia

MR-1. Supply, installation testing & commissioning of submersible pumping set suitable to operate on 410 volts 3 phase 50 HZ A.C. power supply including water proof joint free cable, motor control panel, 50 mm dia, G.I. pipe (medium class) column with fittings, clamps etc. complete in all respect as per details given below : (For Borewell)

DSR-2.10. Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : DSR-2.10.1. All kind of soil DSR-2.10.1.1. Pipes, cables etc, not exceeding 80 mm dia.

DSR-18.9. Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. DSR-18.9.6. 50 mm nominal outer dia Pipes

DSR-18.17. Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : DSR-18.17.4. 50 mm nominal bore

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design : DSR-18.33.1. With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design : DSR-18.37.1. With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) : DSR-18.60.1. 80 mm dia nominal bore

Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts, bolts, rubber insertions etc. complete conforming to IS : 2373 : DSR-18.61.1. 80 mm dia

Supplying, installation, testing and commissioning of Sewage Treatment Plant based on attached growth technology using the "Moving Aerated Bio-media Reactor" (MBBR) process complete mechanical and electrical items with staand by pumps as mentioned below for STP. Electro Mechanical Work Bar Screen- 2 nos Level Switch- 1 set Sewage lifting pump- 2 nos Plant Room Sump Pump- 2 nos Air Blower- 2 nos Air dispersion system Fine bubble diffuser- 1 lot Corse bubble diffuser- 1 lot Air piping- 1 lot Sludge recirculation pump- 2 nos Filter press (Manual)- 2 nos Screw pump- 2 nos MBBR media- 1 lot Tube settler media- 1 lot Filter feed pump- 2 nos Multigrade Filter- 1 no Activated carbon filter- 1 no Pressure guage- 1 lot Dosing pump- 1 no Piping & Fitting- 1 lot Electrical control panel- 1 no Electro Magnetic Flow Meter- 1 no Cable & Cable tray- 1 no Ulta violet (UV) System- 1 no 15 KLD MBBR STP

Internal Electrical Work 1.10.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.(GROUP C)

1.55 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. 1.55.3 Group C

1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed pvc conduit as required. 1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

1.14.5 2 X 10 sq. mm + 1 X 6 sq. mm earth wire

1.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

MR 4 X 25 sq. mm + 2 X 10 sq. mm earth wire

1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

DSR 2022 1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

2.18 Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

DSR 2022 2.20 Supplying and fixing 30 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top along with 30 amps "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

MR Supplying and fixing 63 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top along with 63 amps "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

1.20. Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required 1.20.2 25mm dia conduit

1.20.3 32mm dia conduit

1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 1.21.1 20mm dia conduit

1.21.2 25mm dia conduit

1.21.3 32mm dia conduit

DSR-2022-1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Telephone wire 1.18 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 1.18.1 2 Pair

1.19 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Extra Modular switch/socket outlet 1.24 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 1.24.1 5/6 A switch

1.24.2 2 way 5/6 A switch

1.24.3 15/16 A switch

1.24.4 3 pin 5/6 A socket outlet

1.24.5 6 pin 15/16 A socket outlet

1.24.6 Telephone socket outlet

1.24.7 TV antenna socket outlet

Providing, laying, connecting and testing of multi-core telephone armoured cable of conductor size 0.63mm dia annealed copper conductor PVC insulated PVC sheathed jelly filled (as per DOT specification) cable along wall or ceiling or through existing pipe. MR 20 Pair telephone cable

MR 10 Pair telephone cable

MR 100 Pair telephone cable

Providing, fixing connecting and testing of under noted size of solderless telephone tag block Krone make in surface/recess in wall required size of M.S. box with hinged lockable cover duly stove enamel painted. MR 10 pair tag block

MR 20 pair tag block

MR 100 pair tag block

Extra GI box along with modular base and cover plate 1.27 Supplying and fixing following size/modules, GI box along with modular base and cover plate for modular switches in recess etc. as required. 1.27.1 1 or 2 Module (75mm x 75mm)

1.27.2 3 Module (100mmX75mm)

1.27.3 4 Module (125mmX75mm)

1.27.4 6 Module (200mmX75mm)

1.27.5 8 Module (125mmX125mm)

1.27.6 12 Module (200mmX150mm)

1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

15.2 Supplying,installation,testing and commissioning of Passive Infrared(PIR) technology based occupancy sensor with day light dimming(lighting level shall be regulated as per availability of natural day light in an area along with occupancy detection.) having high preformance, regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 2.8 mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.

1.22 Supplying and fixing metal box of following sizes (nominal size) in floor, surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 1.22.2 100 mm X 100 mm X 60 mm deep

1.22.3 150 mm X 150 mm X 60 mm deep

1.22.6 200 mm X 300 mm X 60 mm deep

FANS & LIGHT FIXTURES: Down Lighter MR Supply and fixing of recess/ Surface/ Pendent mounting round 6 Watt 8 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect.(CAT AAA)

MR SITC of LED Wall bracket Luminaire with E27 base lamp holder suitable for LED bulb of wattage 12W with chrome lamp cup. Similar to Wipro LM91 or equivalent

MR Supply and fixing of recess/ Surface/ Pendent mounting round 10 to 15 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect.(CAT AAA)

MR Supply and fixing of recess mounting round 15 to 18 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect.(CAT AAA)

For Double height MR Supply and fixing of recess/surface mounting round 24 Watt to 32 Watt LED Down Lighter having Powder coated die cast aluminium housing with extended heat sink, diffuser/ Reflector and driver set completed in all respects.(CAT AAA)

2'X2' Square Fittings MR Supply and fixing of 36 Watt to 46 Watt indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect.(CAT AAA)

LED Tube Light MR Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect.(CAT- AAA)

MR Supply and fixing of LED Tube Light with batten suitable for up to 2 X 22 watt LED tube light fitting including tube on Surface complete in all respect.(CAT- AAA)

MR Supply and fixing of water tight oblong 10 Watt LED bulkhead luminaire with driver set confirming to IP 65 and above Protection . complete in all respect.

MR Supply and fixing of Single LED light wall bracket 3 to 6 Watt on matching M.D.F.E.G Board base etc. complete in all respect.

MR Supply and fixing of 3 Watt LED Path / Walkover luminaire having powder cotated die cast aluminium body with drive set . Confirming to IP 65 Protection complete in all respect.CAT-AAA

MR Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 70 to 90 Watt. Confirming to IP 65 protection complete in all respect.(CAT - AAA)

MR Supply and fixingof Mirror Wall Light oblong 10 Watt LED luminaire with driver set confirming to IP 65 and above Protection . complete in all respectsimilar to Philips model No. BN021 LED 10S.

MR Supply, installation, connecting, testing and commissioning of illuminated exit sign with 1 x 6 watt LED lamp including providing maintenance free batteries & charger capable of working for 2 hr duration mounted on ceiling/wall complete with the approved EXIT self adhesive labels as per site requirement as required including connection with 1.5 sqmm FRLS PVC insulated copper conductor similar to Prolite or equivalent

MR Supply & installation LED cove strip 5 Meter length similar to philips Cat No. LED Strip SKYCove 5M WW with copper wiring for looping

MR Supply,Installation, Testing and Commissioning of Specialized 20 watt LED Track lighting system for Museum alogwith with sensors required and track light accessories etc complete in all respect.Similar to Philips Cat No ST271T LED20/840or Panasonic cat No ATR020206

DSR-2022 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

MR Supplying, erection, connecting, testing and commissioning of 750 mm wall circulating fan complete in all respect including fixing wiring connection etc Similar to Usha Dominaire

MR Supplying, erection, connecting, testing and commissioning of 400 mm wall fan complete in all respect including fixing wiring connection etc Similar to havells Platina

MR Supplying, erection, connecting, testing and commissioning of following size exhaust fan complete with gravity louver and connection with 3 core flexible wire as required. a. 380mm 900 RPM

b. 450mm 900 RPM

MR Supply and fixing of single unit LED aviation obstruction light complete with transformer and LED spiral etc complete in all respect..(CAT AAA)

MR Erection and testing of ceiling fan and regulator for room height upto 3.5 metres including supply of 3mm thick G.I.Pipe19mm dia. Duly painted, complete in all respect.

MR Add extra to item (1116) for 15cm or part thereof for room height from 3.5 to 5.00 metres.

MR Erection and testing of exhaust fan on the existing hole with suitable size of rag bolts, nuts and washers etc., complete in all respect.

MR Making hole in the wall for exhaust fan and finishing properly complete in all respect.

MR Supply and fixing hexagonal/Round G.P.fan box of approved make made up of 1.0 mm thick ISI Marked G.P.sheet spot welded Four to Eight holes of 25.4 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed fitted with 300 mm round zink coted M.S Bar X 12 mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material, labour, T&P etc. required for proper completion of the work.

MR Supply and fixing of electronic fan regulator( Modular) 120-280 V. ISI marked, on the existing switch board including making connections, required material, labour T&P etc. for proper completion of work to the satisfaction of Engineer in charge of work.

MR Supplying and fixing M.S. box with Phenolic laminate plate 4- way splitter box for TV antenna complete as required.

MR Supplying and fixing of 450 x 450 x 150 M.S. box with Phenolic laminate plate of 16 SWG M.S. Sheet with hinged door cover for mounting TV amplifier including wooden base plate complete as required.

M.V. PANELS/ DISTRIBUTION BOARD SPN DB Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2.3.1 6 way , Double door

2.3.2 8 way , Double door

TPN DB Supplying and fixing of following ways,horizontal type three pole andneutral, sheet steel, MCB distribution board, 415 V, on surface/ recess ,complete with tinned copper bus bar, neutral link, earth bar, din bar,interconnections, powder painted including earthing etc. as required. ( But without MCB/RCCB/Isolator) 2.4.3 8 way Double door

VTPN DB Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs/MCCB and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 2.5.3 12 way Double door

2.17 Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32 A 415 V "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

DP MCB as DB I/c Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.12.1 40 amps

FP MCB as DB I/c Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.13.2 63 A

2.2. Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 2.2.1 S & F 100 amp. FP MCCB (16KA) Thermal Magnetic Release

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required 2.10.1 Single pole

2.10.4 Triple pole

2.14 Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as 2.14.1 25 A

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required 2.15.1 25 A

Supplying, installation, testing and commissioning of cubical type MV Panel made out of 14 SWG CRCA sheet steel, totally enclosed IP-54 protection, free standing, floor mounted dust and vermin proof, indoor type compartmentalized powder coated of approved shade after antirust treatment (with min seven tanks ) suitable with busbar interconnection with suitable size of copper lead/solid Aluminium strips, control circuits & bottom base channel of MS section not less than 100mmx50mmx5mm (thick), Fabrication shall be done in transportable section ,entire panel shall have a common earth busbar at rear with 2 nos earth stud cable alleys, cable gland plates in two half as required as per single line diagram & specification enclosed with the following switch gears NOTE: All MCCBs shall have Ics=Icu=100% MCB Should be connected throught terminal Strip of suitable rating All outgoing MCCB feeders shall have ON/OFF Trip indication lights (LED Type) Panel Specification as stated above (Power Panel) Incomer 1 No. 315 A FP MCCB (36 KA) 1 Set phase indication lights (R, Y, B)1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-315 Amp. Ammeter (digital type) with inbuilt ASS Provision of Space for dual source energy meter with CT BUS BARS:- 315 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 2 Nos 40 Amp. FP MCB (25 KA) 6 Nos. 100 Amps. FP MCCB (25KA)

Panel Specification as stated above (Lighting Panel) Incomer 1 No. 250 A FP MCCB (36 KA), 1 Set phase indication lights (R, Y, B), 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-315 Amp. Ammeter (digital type) with inbuilt ASS, Provision of Space for dual source energy meter with CT, BUS BARS:- 315 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 2 Nos 160 Amp. FP MCB (25 KA), 6 Nos 63 Amp. FP MCB (25 KA)

Panel Specification as stated above (UPS Panel) Incomer 1 No. 160 A FP MCCB (36 KA), 1 Set phase indication lights (R, Y, B), 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses., 1 No. 0-315 Amp. Ammeter (digital type) with inbuilt ASS, Provision of Space for dual source energy meter with CT BUS BARS:- 200 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 6 Nos 40 Amp. FP MCB (25 KA)

Panel Specification as stated above (Lift Panel) Incomer 1 Nos 200 Amps Automatic Change Over Switch 1 No. 200 A FP MCCB (36 KA) 1 Set phase indication lights (R, Y, B) 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses. 1 No. 0-200 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 400 Amps. TP&N aluminium bus bars (36 KA) OUT GOINGS:- 3 Nos. 125 Amps. FP MCCB (25KA) Sub Outgoing 3 Nos. 40 Amps. DP MCB (25KA)

EARTHING 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

MR Supply and burring of Safe Earthing Electrode T-19 (Hot Dip Galvanized), Length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal Dia 12 mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonry husing (from electrode terminal to switch board, cost of 25 x 3 G.I . strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified

5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

5.1 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re- filling etc. as required.

5.11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

5.12 Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

LIGHTNING PROTECTION SYSTEM 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

6.7 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

6.2 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

6.8 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor complete as required. (For vertical run)

6.14 Supply and lying of 32mm x 6 mm G.I. strip from earth electrode directly in the ground as required complete in all respect.

6.12 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 Nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

17.2.4 Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

17.2.5. Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

17.2.6. Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

17.2.7 Supplying, installation, testing & commissioning of fault isolator complete with base as required.

17.2.9. Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

17.2.10 Supplying, installation, testing & commissioning of addressable fire control module complete as required.(For automatic door closers, elevator controls, fire suppression systems, smoke ejectors etc)

MR Supplying, installation, testing & commissioning of addressable fire monitor module complete as required.

17.2.11. Supplying, installation, testing & commissioning of addressable phone control module complete as required.

17.2.14 Supplying, installation, testing & commissioning of addressable manual call point complete as required.

17.2.15 Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

17.2.17 Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

17.2.19 Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

17.3 PUBLIC ADDRESS SYSTEM 17.3.1 Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

17.3.2 Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

17.3.5 Supplying, installation, testing & commissioning of 6 inches dia, 2 watts, 70/100 volts ceiling speaker complete as required.

17.3.7 Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

17.3.9 Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

17.5 Cabling and Wiring 17.5.1 Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

17.5.2 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

17.5.3 Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. 17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm

17.5.4 Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 1.21.2 25mm dia conduit

1.21.3 32mm dia conduit

UPS SYSTEM MR Supply, installation, testing & commissioning of the following: IGBT based 20 KVA parallel True Online Double Conversion UPS suitable for unbalanced, 3 Phase input and 3 phase 415 V output UPS system with isolation transformer (i.e., K-13 type), suitable for operating in parallel and each comprising as per technical specification complete as required. VRLA sealed maintenance free batteries for 20 KVA UPS system, for providing 30 minutes back up to each 20 KVA UPS. Each bank of batteries shall comprise required Nos. of SMF batteries etc as per specifications as required. Matching cabinet to house SMF batteries for 20 KVA UPS system along with interconnecting links and I/c S/F MCCB as required.

L.V. CABLES Supplying following 1.1kV grade, XLPE insulated, heavy duty armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, galvanised steel armouring and with all components as mentioned in BOQ, specifications, complete as required. 3.5 x 300 sq.mm

3.5 x 240 sq.mm

3.5 x 185 sq.mm

3.5 x 150 sq.mm

3.5 x 120 sq.mm

3.5 x 95 sq.mm

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 14.14.1 100mm dia

14.14.2 150 mm dia.

14.14.3 250mm dia

Supply and making end termination with brass double compression gland including providing and crimping of aluminium solderless lugs / ferrules for XLPE armoured power aluminium conductor cable 1.1 KV grade of following sizes:- 9.1.30 3.5 x 300 sq.mm

9.1.29 3.5 x 240 sq.mm

9.1.27 3.5 x 185 sq.mm

9.1.26 3.5 x 150 sq.mm

9.1.25 3.5 x 120 sq.mm

9.1.24 3.5 x 95 sq.mm

9.1.23 3.5 x 70 sq.mm

9.1.22 3.5 x 50 sq.mm

7.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. 7.1.1 Upto 35 sq. mm

7.1.2 Above 35 sq. mm and upto 95 sq. mm

7.1.3 Above 95 sq. mm and upto 185 sq. mm

7.1.4 Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing masonry open duct or tray as required. 7.6.1 Upto 35 sq. mm

7.6.2 Above 35 sq. mm and upto 95 sq. mm

7.6.3 Above 95 sq. mm and upto 185 sq. mm

7.6.4 Above 185 sq. mm and upto 400 sq. mm

MR Supply and fixing of cable tray/steel work in position including clamps, frame work of flats, angle iron, channel with fabrication work including cutting, bending, welding, drilling bolting etc. as per design as required. One coat of primer and 2 coats of enamel paint of approved shade shall be provided.

Supply and fixing of perforated 2mm thick CRCA sheet steel power coated cable tray of following sizes complete with bend/tee joints, coupling plate & nuts bolts etc. including providing and fixing of M.S. painted hanger etc. as required. 4.1.8 300mm wide 62.5mm depth

4.1.10 450mm wide 62.5mm depth

4.1.14 600mm wide 75mm depth

4.1.15 900mm wide 75mm depth

7.10 Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

SUB-HEAD -III: EARTHING 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.8 Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

5.9 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

5.10 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re- filling etc. as required.

5.11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

TRANSFORMERS Supplying, installation testing and commissioning of 400 kVA, outdoor type, oil cooled, distribution transformer, suitable for 3 phase, 50HZ, AC supply, rated turn/voltage ratio of 11kV/0.433kV,Dyn 11 vector group, percentage impedence of 4.5%, oil immersed naturally cooled (ONAN) mechanism,core made of good quality CRGO, windings made of double wound copper, insulation class A,approved danger and arc flash signages and with all components as mentioned in BOQ, specifications and SLD & confirming IS 1180 Level-II losses, complete as required. Cable termination box with disconnecting facility for 11 KV XLPE cable at 11 KV side suitable for 11kV(E) 3C x 300 sqmm XLPE Cable, Bus Trunking Provision LV Side of Transformer as per SLD, Off load tap changer +5 to - 15 % in the steps of 1.25 with AVR, Bi directional rollers, Conservator with drain valve, Earthing terminals. Explosion vent with double diaphragm and sight glass. Radiator with top & bottom shut off valve., First filling of oil including make up fill. Rating and diagram plate. Air release plug. Buchholz relay with shut off valve. Winding temperature indicator. (WTI), Oil temperature indicator. (OTI), Magenatic oil level gauge. Pressure relief device. Marshalling box with watertight lockable cover lid and all associated accessories as per schedules and specifications. Drain cum bottom filter valve, Oil surge relay.

Supplying and fixing of non-skid rubber mat 16mm thick and 900mm width as required including cutting to required lengths of approved make with Test Certificates for L.T. panels.

Supplying and fixing of fire bucket painted red and duly filled with sand conforming to IS: 2546-1974.

Supplying and fixing of MS stand suitable for supporting two buckets (Pedestal type)

Supplying and fixing of MS stand suitable for supporting four buckets (Pedestal type)

Supplying and fixing of shock restoration chart written in English and Hindi duly framed in as required.

Supplying and fixing of carbon dioxide fire extinguisher type 4 kgs. Capacity of approved make with wall mounting bracket as required conforming to IS: 2878/1976 (Push type).

Supplying and fixing of first aid box as approved complete with standard kit as prescribed by Indian Red Cross.

Supply and fixing of H.T. Danger notice plate of 250x200mm made of mild steel at least 2mm thick and vitreous enameled white on both side with inscription in signal red colour on front side as required.

D.P. Structure, H.T. Panel Board, Battery Charger & HT Metering Panel Supply, erection, testing and commissioning of H Pole (double pole) structure in position 13M long MS pole (Swaged type) as per IS-410 SP-70 with latest amendment and necessary anti climbing devices, cross arms, bracing, clamps and painting with one coat of primer and two coats of aluminium paint including circuit marking etc. as required. The poles to be erected in cement concrete foundation of 1:2:4 with collar including excavation in soil (600mm(L) x 600mm(W) x 1800mm(D)) and making goodcomplete as required.

13.1 Supplying and erection of galvanised stay set for 11 KV over head lines complete with 19/ 20 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm thick, thimble, stay clamps, turn buckle ( 20 mm X 600 mm ), 7/ 4.00 mm dia G.I. stay wire and 11 KV strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required.

13.24 Supply, erection, testing and commissioning of 11 KV disc insulator for 33 KV over- head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as required (9 Nos Set : 3 Nos for each phase)IS: 731-1963 and 3188-1965 for disc insulator.

13.23 Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required.

Supply, erection, testing and commissioning of 11 KV, 3 phase, 630 Amps central post racking type gang operated switch with earth switch complete with hardware, arcing horns, arcing contacts, vertical drop out fuses, down rod operating with locking devices, necessary MS channel/angle iron brackets, clamps insulators & connections etc. as required for earthed system and conforming to IS: 19813.

Supply, erection, testing and commissioning of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 30 KV (rms) with a nominal discharge current rating of 10 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

5.15 Supply, erection, testing and commissioning of 25x5mm GI earth strip including clamps and binding etc. as required as per specifications and drawings.

Supplying and laying of the 250mm dia 'B' class GI pipe complete with all accessories as required as per specifications.

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required. 10.4.4 3Cx300 Sq.mm.

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required. 10.5.4 3Cx300 Sq.mm.

Supplying and making straight through cable jointing with heat shrinkable jointing kit complete with all accessories including ferrules suitable for following size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required. 10.6.4 3Cx300Sq.mm.

EXTERNAL STREET LIGHTING Supplying, installation, testing and commissioning of L.T. panel fully compartmentalized cubical type sheet clad floor mounted totally enclosed , extensible on both sides, switch board suitable for use on 415 Volts 3-phase, 4 wire, 50 Hz system having required fault capacity, housed with incoming and outgoing, Aluminium bus bars with current rating of 0.8 Amp/sq.mm, interconnection etc. with indication lamps, accessories etc, as required as per specification and schematic diagram as required. (Street lighting Panel) INCOMER:- 1 Nos.160 Amps. TPN MCCB(25 KA) with electronic releases., 1 Set phase indication lights (R, Y, B), 1 No. Volt Meter (digital type) with inbuilt VSS & control fuses., 1 No. 0-200 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:- 200 Amps. TP&N Aluminium bus bars (25 KA) OUT GOINGS:- 8 Nos. 40A TPN, MCB (10KA) . 6 Nos. 24 Hr Timer Switch, 6 Nos. 63A TPN contactor

Supply and fixing of decorative 40 to 45 Watt LED Post top indirect light luminaire having Pressure die cast aluminium body and Clear glass with driver set confirming to IP 65 and above protection complete in all respect including connecting copper wiring.CAT-AAA

Supply & Erection of 3/4 meter long GI Decorative pole for above post top fitting with inbuilt junction box,MCB,sleeve in foundation and required wiring till fixture in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

Supply and fixing of decorative 8 to 16 Watt LED bollard luminaire with driver set confirming to IP 65 protection complete in all respect including foundation and connecting copper wiring. CAT-AAA

Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 140 to 150 Watt. Confirming to IP 66 Protection complete in all respects including connecting copper wiring (CAT- AAA)

Supply & fixing of 9mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 155 mm and base plate 12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and with inbuilt junction box with MCB,and wiring till fixture, sleeve in foundation,Required T&P completee in all respect.

Supply & fixing of 9 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 155 mm and base plate 12mm thik) having 3mm thikness with Double arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and with inbuilt junction box with MCB,and wiring till fixture,sleeve in foundation, Required T&P completee in all respect.

Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 70 to 90 Watt. Confirming to IP 65 protection complete in all respect including connecting copper wiring.CAT-AAA

Supply and burying of 40mm dia x 4.5 metres long G.I. Pipe vertically for earthing having 12mm dia. Holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No. 6 to 8SWG GI wire in G.I. Pipe up to appron (and from appron to switch board the cost of G.I. wire and pipe will be extra) upto switch board, 30cm square C.I. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respects as per drawing.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

14.16.2 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.90 mm dia (OD-90 mm & ID-76 mm nominal)

14.16.3 120 mm dia (OD-120 mm & ID-103 mm nominal)

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required 14.13.2 80 mm dia

14.13.3 100 mm dia

D.G. SETS Design, supply at site, installation, testing & commissioning of 3-phase, 415 volt, 1500 RPM, 50 HZ, Diesel generator set with prime rating capacity of 250 KVA at 0.8 pf lagging diesel engine alternator set mounted on common base frame in outdoor type acoustic enclosure , day tank, with PCC Panel with AMF Panel,Adopter box with AL extended bus bar, battery, batter charger, return fuel cooler, anti vibration mounting pads including residential silencer, engine alternator, pcc based auto start & synchronization set, safeties with accessories as per specification complete as required. Diesel engine shall conform to IS:10000 and alternator shall be self excited complete with AVR to IS:4722.Genset should be capable to take an average loading of minimum 85%. net output shall be designed @ 50 degree ambient .Synchronisation should be based on No Master Logic for system reliability . Any genset reaching rated RPM should automatically become master .AVR should be digital type AVR to provide fast response with respect to change in load , it should provide digital governing with digital isochronous synchronisation. To improve the reliability of the System , the synchronizing module should be part of Engine Controller . No external controller should be used for synchronising and shall not be accepted.Genset controller should have Weak Battery Monitoring system . The control system should test the battery each time the genset is signalled to start and indicate a warning if the battery is weak

SOLAR PV CELL Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.

IP CCTV System SITC of IP Dome Camera 4MP IR Dome Camera, Metal Housing, H.265+/H.265/H.264, Up to 2592x1520 @ 25fps, Min. illumination Color: 0.002Lux @ F1.6, Smart IR, IR Range: 30m, Built-in Mic, SD Card Slot, Reset Button, POE, IP67, IK10, 120dB WDR, Support tripwire and perimeter, ANR. BIS,CE,FCC,ROHS,UL/EN. etc all complete. Make: Pelco / Royalshield / Bosch / Axis

SITC of IP Bullet Camera 4MP IR Bullet Camera, Metal Housing, H.265+/H.265/H.264, Up to 2592x1520 @ 25fps, Smart IR, IR Range: 50m, Built-in Mic, SD Card Slot, Reset Button, 120dB WDR, POE, IP67, 120dB WDR, Support tripwire and perimeter, ANR. BIS,CE,FCC,ROHS,UL/ENetc all complete. Make: Pelco / Royalshield / Bosch / Axis

SITC of IP PTZ Camera 2 MP -IP PTZ Camera 2 MP - IP Network 1/2.8" CMOS, Dual IR Cut Filter , 1920x1080:30fps, H.264/MJPEG Or better, Triple streams, AC24V/POE+, IP66, Micro optical zoom(4.6 ~ 152mm), IR range: up to 150m, 120dB WDR, IP66, 33X optical zoom, HLC,BLC,3D DNR, Smart functions-Auto Tracking, CE, FCC, Defog, Privacy mask, Up to 8 Pattern, Presets – 300 , PAN Range - 360° , 0.1°/s ~ 180°/s ,Tilt Range -–16° ~ 90° (auto flip) , 0.1° ~ 120°/s etc all complete. Certificate – BIS, CE, FCC, ROHS, UL/EN etc all complete. Make: Pelco / Royalshield / Bosch / Axis

SITC of NVR - H.265 8SATA 64ch NVR, H.265+ Compression, Support 64-ch input, Up to 12MP Resolution Recording, Incoming Bandwidth 320Mbps, Outgoing Bandwidth 320Mbps, HDMI and VGA independent outputs, HDMI Video output at up to 4K (3840 × 2160) resolution, 8 SATA interfaces for 8 HDDs, up to 10TB for each HDD, eSATA interface:- 1 SATA interface, 2xRJ45 self-adaptive 10/100/1000 Mbps network interfaces, VCA detection alarm is supported, Array Type:- JBOD, RAID0/1/5/6/10, 2xUSB 2.0, 1xUSB 3.0, serial Interface:- 2xRS-485, 1xRS-232, No.of Hard Disks 4TB for the calaculation of 1 month recording 2MP@25FPS as per all camera count, VMS should also be included if required etc. all complete. Make: Pelco / Royalshield / Bosch / Axis

SITC of 10 TB Survillance Sata Type HDD for Network video Recorder etc all complete Make : WD / Seagate

SITC of MS Windows 2008 Server R2 x64, Intel i5 Xeon Quad Core processor, 8 GB RAM, 1TB HDD, 2GB Graphics Card. With CD/DVD player, Mouse and Keyboard etc all complete. Make : HP / Lenevo / Dell

SITC of 55" Professional Display Panel, 4K/UHD Resolution, Direct-lit LED, Brightness 400 nits, Contrast ratio 1200:1, inputs: 2 HDMI, DVI, DisplayPort, Audio inputs with mounting arrangements etc all complete

HVAC WORKS VRV Out Door units : Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/ Variable Refrigerant Volume aircooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s) ,minimum two compressors for above 14HP modules, microprocessor based Controller ,top discharge type condensing unit(s), with R410A Refrigerant ,vibration isolators ,with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Condition s and work even at 50°C ambient temperature without tripping. The units hall be suitable t owork on 400V+/-10%,3Phas e,50Hz AC power supply .The unit shall be filled with first charge of the refrigerant and ready for use as required .The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 (Approved Makes :Daikin /Toshiba/ General /Mistribushi /Voltas ) Outdoor Units 20 HP

2.2 Supply,installation,testing and commissioning of following minimum capacity4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media prefilter ,fan section with low noise fan/dynamically balanced blower ,multi speed motor ,coil section with DX Copper coil,electroni cexpansion valve, outer cabinet ,drain pump,grill,necessary supports,vibration isolation, cordless remote control etc.,suitable for Operation on single phase 230V±10%,50Hz AC supply ,complete ,as required. The unit shall have automatic force shut down provision in case offire on receiving signal from BMSSystem .The cooling capacity of indoor unit will beat air inlet conditions of 27 Degree CDB and 19 Degree CWB temperature.(Approved Makes: Daikin/Toshiba/General/Mistribushi/Voltas) 1 TR

Supply, Installation,testing and commissioning of corded remote controls as per drawing and specifications (Approved Makes: Daikin/Toshiba/General/Mistribushi/Voltas)

Supply,Installation,testing and commissioning of centralised remote controlers as per drawing and specifications

Interconnecting 'Y' Joints i.e. Refnet Joints/ Header with Y-joints and headers

5. Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class- 0 tubular insulation/with Class-0 closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc with necessary refrigerant joint as required. 5.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

5.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

5.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

5.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

5.5 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

5.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

5.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

5.1 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with19 mm thick insulation

5.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

Supply installation testing commissioning Shielded Control Cables for VRV System with necessary ISI mark Medium class rigid PVC pipes with necessary accessories with termination in machine and control equipments. (A) 2C X 1.5 Sq mm Shielded Armoured(for transmission)

(B) 2C X 1.5 Sq mm Shielded Armoured(for remote)

Propellar Type Fan Supply,installation,testing and commissioning of Propeller type free discharge exhaust fans complete with motor , fan ,exhaust Louvers as per drawings and specifications. 200 mm dia

Inline Ducted Type Exhaust /FRESH AIR Fans Supply, Installation, testing and Commissioning of ceiling / floor mounted Rectangular box type/circular type Inline fan, for toilet exhaust , ot exhaust , lab exhaust constructed of GSS duly powder coated as per detailed specifications, complete with forward curved SISW fan, motor and drive suitable for 220 ± 10% volts, 1 phase, 50 Hz A.C supply, with necessary canvas connection etc complete in all respects. 350 cfm at 10 mm static

250 cfm at 10 mm static

Rectangular ductwork for toilet Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 24 Gauge (thickness 0.63mm sheet)

Supplying & fixing of powder coated extruded aluminium Supply air grill/ Return Air Grills with louvers but with/without volume control dampers complete as required.

Drain Piping : Supply,installation,testing and commissioning of of CPVC pipes having thermal stability for condesate water including wrapping of 9mm thick class 0 nitrile rubber insulation with suitable adhesive with all CPVC plain and brass threaded fittings including the pipes with clamps 1metre spacing.This including jointing of pipes with one step CPVC solvent cement and testing of joints complete as per drg and specifications 50 mm dia

40 mm dia

32 mm dia

25 mm dia

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with bends , reducer and all accessories ,connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm width X50 mm depth X1.6 mm Thickness

150 mm width X50 mm depth X1.6 mm Thickness

300 mm width X50 mm depth X1.6 mm Thickness

450 mm width X50 mm depth X2 mm Thickness

LIFT WELL PRESSURIZATIONFANS-Supply, installation, testing and commissioning of AMCA Certified (For Air and Sound Performance) vane axial flow fan of different capacity as mentioned in schedule in standard M.S. construction. Entire fan model & AMCA seal shall appear in technical submittal of fan. All the fans are synthetic enamelled painted / hot dip galvanized with minimum 220 GSM Zinc coating and complete with bird screen at Inlet. The electric motor coupler shall be squirrel cage induction motor (EFF-2 type) confirming to IS-325 IP 55 with class H insulation. . Fan efficiency should not be less than 60% noise level shuld not be more than as specified in schedule when measured in hemisperical reverberant room conditions with backdraft damper. Fans should be as per specification and drawings. 3500 CFM - 25MM STATIC

Supplying following 1.1kV grade, XLPE insulated, heavy duty armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, galvanised steel armouring and with all components as mentioned in BOQ, specifications, complete as required. 3 Core 16 Sqmm. Alum. Armd

3 Core 10 Sqmm. Alum. Armd

3 Core 6 Sqmm. Alum. Armd

Earthing : Supply,installation,testing and commissioning of following double earthing continuity conductor of Cu from Panels to respective equipment on surface or recess as per drawings and specifications. a) 25 mm X 5 mm strip

8 SWG wire

Costruction of 11KV H.T. Line for 0.5 KM distance including load security, supervision charge and other charges payable to the APDCL authority as required complete. 2.22 Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

5.2 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

5.7 Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

5.9 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

13.1 Supplying and erection of galvanised stay set for 11 KV over head lines complete with 19/ 20 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm thick, thimble, stay clamps, turn buckle ( 20 mm X 600 mm ), 7/ 4.00 mm dia G.I. stay wire and 11 KV strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required.

13.4 Supplying of channel iron 75 mm X 40 mm X 6 mm (7.14 kg per metre) cross arm for two 11 KV over head line conductors complete with 50 mm X 50 mm X 6 mm (angle iron bracket welded to the channel iron and complete with 50 mm X 6mm M.S. flat iron clamps, bolts and nuts including drilling holes for insulator pins, bolts, nuts and washers etc (as per drawing) and painting with primer and finish paint as required.

13.6 Erection of pole top/ straight two wire/ V shape two wire, angle iron/ channel iron, cross arm on steel tubular/ rail/ PCC pole for 11/22/33 KV as required.

13.10 Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required.

13.11 Supplying and erection of 11 KV disc insulator for 11 KV over head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as required.

13.13 Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

13.19 Supplying of channel iron 100 mm X 50 mm X 6 mm (9.56 kg per metre) cross arm for two wire 33 KV over head line conductors complete with 50 mm X 50 mm X 6 mm angle iron bracket welded to the channel iron and complete with 50 mm X 6mm M.S. flat iron clamps, bolts and nuts including drilling holes for insulator pins/ fittings, bolts, nuts, washers etc and painting with primer and finish paint as required .

MR-1 Supplying including erection of 12.0 Mtr. G.I. Steel Tubular Pole (410sp-66) (Stnd. Weight 322 K.g.) along with fitting fixing, excavation work, foundation of bolts and nuts in R.C.C. work in 1:3:6 proportion of 1.80 Mtr. depth, Cement plastering and etc. complete with all necessary materials as required and specified by the Department.

MR-2 Supply of following size of GLOSTER Brand HT cable with stranded compect circular Aluminium conductor, Conductor screened with Extruded semicnducting compound, XLPE Insulated, Insulation Screened with Extruded semiconducting compound in combination with Copper Tape, Aluminium Dlat Strip/ Round Wire armoured and overall PVC ST2 Sheathed cable (Conforming to IS:7098 Part-II 2011) as specified and directed by the deptt. (GLOSTER or equivalent make as approved by this Deptt.) 120.00 sq.mm 1 Core U.G. Armoured H.T. Cable.

MR-3 Supplying with fitting and fixing 11KV 1 Core x 120 Sq.mm covered conductor cable Termination Jointing Kit - 11 KV (Straight through Type) with all necessary material complete as required and as directed by the Dept.

MR-4 Supplying with fitting and fixing 11KV 1 Core x 120 Sq.mm covered conductor Wedge connector Kit - 11 KV (Straight through Type) with all necessary material complete as required and as directed by the Dept.

MR-5 Supplying and fixing of 11 KV GOAB Switch 400 A Gang operated switch with all accessories complete as required and as directed by the department.

MR-6 Supplying and fixing of 11 KV 150 A D.O. fuse set complete as required and as directed by the department.

MR-7 Supplying with binding of HT ACSR AAA Reccon conductor as required complete.

Payment to be made to APDCL authority against Load Security.

Supervision, meter security and other liasioning charges payable to APDCL / Licensing Authority for construction of 11 KV H.T. line, Transformer Sub-station etc.

ROAD WORKS DSR-16.1. Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating carth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller DSR 16.1 including making good the undulations etc, and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

DSR-1.12. Carriage of material by mechanical transport including loading, unloading to 5km.

DSR-4.1.8. Providing and laying Cement concrete 1:4:8 (1cement :4 coarse sand :8 graded stone aggregate 40 mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete, also including cost of formwork in foundation.

DSR-16.78.1. Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

DSR-16.43.1. Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with direction of approved joint filler and sealants, complete all as per Engineer-incharge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum Excess less cement used as per design mix is payable/ recoverable separately. Cement concrete prepared with batch mixing machine

DSR- 5.22A.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-5000 or more.

16.45 DSR Providing and fixing in position pre-moulded joint filler in expansion joints.

16.46 Providing and laying in position bitumen bot sealing compound for expansion joints etc. 16.46.1 Using grade 'A' sealing compound.

DSR 16.47.1 Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-incharge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign mater;al etc. and lining out complete. New work (Two or more coats)

DSR 16.67.1 Varnishing with varnish of approved brand and manufacture Two or more coats glue sizing with spar varnish or an under coat of flatting varnish

DSR 16.59.Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual). symbols and borders etc. as per IRC; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM- D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to MS. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size. steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours). Back side of aluminium sheet to be painted with two or more coats of epoxy lifts etc. complete as per drawing, specification and direction of Engineer-in-charge. Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm

DSR 16.59.2. Cautionary warning sign boards of equilateral triangular shape 16.59.2 having each side of 900 mm with support length of 3650 mm

PATH WAY Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in- charge. All

Providing and laying Cement concrete 1:4:8 (1cement :4 coarse sand :8 graded stone ballast 40 mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete, also including cost of formwork in foundation.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer- In-Charge. With material conforming to Grade-1 (size range 75 mm to 0.075 mm) having CBR Value-30

Class-150 brick work in 1:6 cement and COARSE sand mortar in foundation and plinth including supply of all materials, labour tools and plants, etc. Required for proper completion of the work.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand) External plaster

BOUNDARY WALL 2.6.1. Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

CONCRETE WORKS 4.1.8. Providing and laying Cement concrete 1:4:8 (loement 4 coarse sand :8 graded stone ballast 40 mm nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete, also including cost of formwork in foundation.

4.10. Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12 5mm nominal size)

REINFORCED CEMENT CONCRETE WORK 5.22A.6 DSR Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

5.33 DSR Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/ Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS:9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. 5.33.1.1 All works upto plinth level. Concrete of M25 grade with minimum cement content of 330 kg/cum

5.33 DSR All works above plinth level upto floor V level. Concrete of M25 grade with minimum cement content of 330 kg/cum 5.33.2.1 All works above plinth level upto floor V level. Concrete of M25 grade with minimum cement

5.9 DSR Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1 DSR Foundations, footings, bases of columns, etc. for mass

5.9.6 DSR Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.5 DSR Lintels, beams, plinth beams, girders bressumers and cantilevers

5.18.2 DSR Providing precast cement concrete Jali 1:2.4 (1 cement: 2 coarse sand(zone-II): 4 graded stone aggregate 6mm nomina! size), reinforced with 16 mm dia mild steel wire, including centering

BRICK WORK 6.4.2. Brick work with common burunt clay (non modular) bricks of class- 150 in superstructure above plimth level up to floor five level in all shapes and size in Cement mortar 1:6 (1 cement: 6 coarse sand)

FINISHING WORK 13.5.2 DSR 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand) External plaster

13.45.1 DSR Finishing walls with textured exterior paint of required shade New work (Two or more coats applied @ 3.28 ltr/10 sqro) over and including priming cost of exterior primer applied @ 2.20kg/10 sqm

13.80. Providing wall putty on new surface with approved quality material of Berger JK Birla or similar make

5.29 Providing and fixing sheet covering over expansion joints with iron screws as per design 5.292.2 Alummium fluted strips 3.15 mm thick 200 mm wide

HORTICULTURE & LANDSCAPING 2.4. Supplying and stacking at site dump manure from approved source, including carriage upto 1 km (manure measured in stacks will be reduced by 8% for payment) 2.4.1. Screened through sieve of I.S. designation 20mm

2.9 Mixing earth and sludge or manure in proportion specified or directed.

2.13. Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20%: one part stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, levelling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, with in a lead of 50 m lift upto 15 m complete

2.16 Providing and fixing M.S flat iron tree guard 6 cm dia and 2 m high, above ground consisting 4 nos 25X6 mm, 2.25 m long and 8 nos 25X3 mm 2m long verticals M.S flats, riverted to 3 nos 25X 6 mm M.S flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting twocoats with synthetic enemal paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250X100 mm shall be welded to the tree and the middle height guard near lettered CPWD/PWD/any other approved name. The tree guard shall be suitably fixed to the ground by embedding four les of tree guard in pits of suitrable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisaction and direction of officer- n-charge.

2.30.1. DSR -Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20 2.30.1 cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5

7.16 Supplying and stacking of Cassiafistula (Amaltash) plant of height 120 to 135 cm in big poly bag of size 25 cm as dir. of officer incharge.

7.24 Supplying and stacking of Delonix reia (Gulmohar) plant of height 150 to 165 cm in big poly bag of size 25 EACH 10 cm as dir. of officer incharge.

MR Supplying and stacking of Pride of India plant of height 150 to 165 cm in big poly bag of size 25 cm as dir. of officer incharge.

7.2. Providing and stacking of Adansonia digitata (kalp vricksh) of ht 150-165 cm in bag size of 25 cm as per direction of the officer-in-charge.

7.5. Supplying and stacking of Azadirachta indica (Neem) plant of height 120 to 130 cm in big poly bag of size 25 cm as dir. of officer incharge.

5.22 Providing and Displaying Ficus Nuda Topairy well developed with fresh & healthy 5 to 6 big ball specific size and shape 180to 210cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

5.27 Providing and Displaying Ficus resnold Topairy well developed with fresh & healthy 6 to 7 big ball specific size 210 to 240 cm ht in 45 cm Cement Pot as per direction of the officer- incharge.

MR -Detail of tree Fishtail palm

Silver Oak 4-7 m folliage

Anar (30) 2-7 m folliage

Chiku (24) 3 -8m folliage

Mango (24) 3 -8m folliage

Rudraksha Tree 5-15m Folliage

Rain Tree

Peepal tree

Kadam 6'-8' ht

Pakad

Morchari

Chitwan 6-8' ht

SHRUS (have several woody item) Coral Hibiscus 2'-3' ht

Massanda Pink 2'-3' ht

Kachnar 5'-6' ht

Bottle Brush 5'-6' ht

Ixora 2'-3' ht

Ficus black Tapori 3'-4' ht

Ground edging Plant Eranthemum

Verbena

Setcreasea

Verbena Mix

Providing & laying RCC bench

Electrical Lawn mover power Grass cutter & power weed shear

LIFT 13 P (884 KG) (With m/c Room) Lift with speed of 1.5 M/Sec., power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (dimensions and travelling as per drawing)

20 P (1360 KG) (With m/c Room) Lift with speed of 1.5 M/Sec.,power operated doors, ACVVVF Control, and automatic rescue operation during power failure. (dimensions and travelling as per drawing) Addition and deletion of cost per floor on below stated size of lift as per requirement of site (dimensions and travelling as per drawing)

Pabitra Saikia

Bidder Name

Marjit Basumatary & Khaneswar Boro-JV