CWEAFJ-37/2019-20 SPECIAL REPAIR TO BUILDING NO P-7 (AIRMEN BILLET) AT DAINKUND AND PROVISION OF PERIMETER PATH ALONG THE BOUNDRY WALL AT BAKROTA UNDER AF STN DALHOUSIE

Amount

Taking down cement plaster or cement lime plaster of any description complete all as specified and directed.

Demolition of brickwork or stone/boulder built in cement mortar complete all as specified and directed.

Brickwork with subclass `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Rendering 15mm thick in cement plaster 1:4 using WPC (WPC to be measured and paid seperately) on fair faces of brick work or concrete surfaces ,finished even and smooth without using extra lime or cement complete all as specified and as directed by the Engineer-in-Charge

Supply only liquid water proofing compound pidilite LW complete all as specified and directed .

Applying two coats of oil bound distemper on new prepared plastered surfaces complete all as specified and as directed by Engineer-in-Charge.

Two coats of exterior acrylic paint of any shade as approved by GE on new plaster surfaces as per manufacturer's instructions complete all as specified in camouflage pattern as directed by Engr-in-Charge.

Dismantling plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed by Engr-in-Charge.

0.63mm Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in lie of screws with grade of zinc coating 275 complete all as specified and as directed by the Engineer-in-Charge

0.63mm Plain Galvanised, mild steel sheeting in ridge, hips vally gutters drip and straight flashing (length and girth as fixed) with grade of zinc coating 275 complete all as specified and as directed by the Engineer-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge

Non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm in floors over and including 15mm thick screed bed in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Glazed Coloured Ceramic tiles in vertical surfaces 450x350x7mm thick set over and including 15mm thick rendering in CM 1:4 and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

Taking up or down steel tubing of any bore and connections including fittings and cleaning for re-fixing or removal from site 15mm,20mm and 25mm bore GI tubing complete all as specified and directed.

15mm bore GI tubing medium grade with all fittings and fixed complete to wall and ceiling or laid in floor, complete all as specified and directed.

20mm bore GI tubing medium grade with all fittings and fixed complete to wall and ceiling or laid in floor, complete all as specified and directed.

Lagging to 20mm bore GI pipes used in internal water supply or plumbing all round with, 25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842, provided with chicken mesh wire netting 25 gauge, 20mm mesh complete and all as specified and directed.

Stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle fancy type chromium plated (Bore of pipe 15mm) fixed in repairs complete all as specified and directed

Vitreous chinaware wash hand basin white, flat back of size 550x400 mm excluding tap but including brackets fixing to wall and two Nos 10mm dia 100mm long nut and bolt over brackets including 32mm bore PVC waste pipe and CP waste coupling complete and fixed in repair complete all as specified and as directed.

15 mm dia brass CP pillar tap, central hole basin mixer complete fixed in repair, complete all as specified and directed

Vitreous china urinal, half stall type, white and including all fixing accessoies, fixed as in repair complete all as specified and directed. MAKE : HINDWARE Cat Part No 60011 or equivalent in makes given in list of makes

S&F in replacement 15 mm dia stop valve/angle valve chromium plated with long shank concealed type cast copper alloy ISI marked with crutch or butter fly handle high pressure screwed down complete all as specified and directed.

Bib taps suitable for 15mm bore pipe long body with wall flange neck fancy type brass CP with, clutcher butter fly handle screwed down screwed for iron pipe or brass ferrule complete and all as specified.

Brass CP mixer for mixing hot & cold water screwed for iron pipe 15 mm dia and fixed complete all as specified and directed

15 mm dia angle stop valves, cast copper alloy, chromium plated, fancy type, screwed down high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions, fixed in repairs, complete all as specified and directed.

15mm dia PVC connection with brass check nut of length 450mm complete all as specified and directed by Engr-in-charge.

Supply and fixing in repairs vitreous chinaware water closet (Orissa Pattern) long pan of size 580mm x 440mm white with integral foot rests with ‘P’ or ‘S’ trap front or back inlet complete including provision of cement concrete bedding complete fixed in repair and all as specified and directed by Engineer-in-Charge.

PVC valve less syphon action type low level flushing cistern 10 liters capacity with inlet, ball valve, lever, push button type handle including telescopic flush pipe 32mm dia of PVC with long bend of 32mm dia complete and all as specified

Chromium plated tubular towel rails 20mm dia, 60cm long fency type including brackets complete all as specified and directed.

75mm Cast iron floor trap with CP steel grating, having weight of grating not less than 35 Grams, jointed to waste pipe Complete all as specified and directed.

Supplying, Hoisting and fixing in position, 500 litre capacity, polyethylene water storage tanks triple layered, of any shape, including making necessary connections fixed in repairs complete all as specified and directed.

Ball brass valves, high pressure, with polythene float and flunut complete, screwed for iron pipe or brass ferrule and fixed 20mm bore complete all as specified and directed.

Taking down chowkat with shutter without taking off shutter from frame area n.exc 1.5m sqm each and removing to store complete all as specified and directed.

Factory made Steel window 1.25mm thick box type(primer coated) ERW hollow P section of size 60mmx25mm including grill using 10 sqmm bar double rebated both gauge and glass shutter comprised gauged glazed Skelton shutter ERW sec 50mmx20mm and 1mm thick with two openable leaf consisting two Nos sash bar of T Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T Section of size 60mmx25mm and 1.25mm thick refer TD Drawing No CEAF/AR-480/2015 Sheet No 2(A)/4 dated 30.12.2015 including cutting holes and good dismantled portion in PCC(1:2:4) type B1 four Nos for each window including following fitting welded to frame shutter : (a) Hold fast,150mm long of 12mmx3mm made to shape O4 Nos per window (b) handle of Z Sec20mmx25mm, 100mm long-per No leaf (c) MS Tower bolt 150mm long-02No per leaf . (d) Z section 20mmx25mm, 100mm long stopper 1 No per leaf. (e) cleat 55mm long of hollow square 15mmx20mmx63mm welded to hinge. 1 No per leaf (f) MS Pintal hinges of size 75mmx12mm. 2 Nos per leaf, (g) Stainless steel wire cloth, 0.25 mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to 2mm & fixed with alluminium wire staples (h) Glass pane 3mm thick fixed with MS pin and oil putty (j) Including two coats of synthetic enamel paint complete. (k) Including taking down exisitng window. NOTE: During Fixing of Window, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.

Factory made Ventilator 1.25mm thick box type(primer coated)ERW hollow P section of size 60mmx25mm including grill using 10 sqmm bar double rebated both gauge and glass shutter comprised gauged glazed Skelton shutter ERW sec 50mmx20mm and 1mm thick with two openable leaf consisting two Nos sash bar of T Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T Section of size 60mmx25mm and 1.25mm thick refer TD Drawing No CEAF/AR-480/2015 Sheet No 2(A)/4 dated 30.12.2015 including cutting holes and good dismantled portion in PCC(1:2:4) type B1 four Nos for each window including following fitting welded to frame shutter : (a) Hold fast,150mm long of 12mmx3mm made to shape O4 Nos per window (b) handle of Z Sec20mmx25mm, 100mm long-per No leaf (c) MS Tower bolt 150mm long-02No per leaf . (d) Z section 20mmx25mm, 100mm long stopper 1 No per leaf. (e) cleat 55mm long of hollow square 15mmx20mmx63mm welded to hinge. 1 No per leaf (f) MS Pintal hinges of size 75mmx12mm. 2 Nos per leaf, (g) Stainless steel wire cloth, 0.25 mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to 2mm & fixed with alluminium wire staples (h) Glass pane 3mm thick fixed with MS pin and oil putty (j) Including two coats of synthetic enamel paint complete. (k) Including taking down exisitng ventilator. NOTE: During Fixing of Window, surface Shall be make good in plumb with existing finishes

Taking down chowkat with shutter without taking off shutter from frame area exc 1.5m but n.exc 4 sqm each and removing to store complete all as specified and directed.

Supply and fixing factory made pressed steel frames for doors fabricated from 1.25 mm thick sheet, with double rebate including necessary fixing lugs, hinges, lock strike plate, etc. & one shop coat of priming, of profile width 125mm x 60mm, complete all as specified and directed.

Supply and fixing factory made pressed steel frames for doors fabricated from 1.25 mm thick sheet, including necessary fixing lugs, hinges, lock strike plate, etc. & one shop coat of priming, of profile width 105mm x 60mm, complete all as specified complete all as specified and directed. .

PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in filling in steel frame complete all as specified and directed.

Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening, complete all as specified and directed.

Supply and fixing factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

Supply and Fixing glazed and gauged Skelton shutter (Factory made) 35mm thick of second class hard wood (hollock) open rebated & prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut & mitred beads for securing glass etc including priming coat. Size of members of shutters as specified in SSR Part I Section 8, clause 8.20 (a) including Kiln seasoned and chemically pressure treated, with a shop coat of pink primer complete all as specified & directed.

Supply and Fixing flush shutters 35mm thick factory made solid core construction with block board core and ply wood face panels commercials type on both side complete all as specified & directed.

100mm long but hinges medium weight cold rolled mild steel complete all as specified and directed.

150mm long aluminium handles, cast type, anodised complete all as specified and directed.

150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified.

Aluminum alloy, anodized, sliding door bolt (ISI Marked) 250mm long hasp , staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed complete all as specified and directed.

Dismantling Wooden boarding, any description, fixed in any position with nails complete all as specified and directed by Engineer-in-Charge.

2nd class hardwood 40mm thick boarding in floors and skirting, with butt joints, fixed with nails in any situation including preparation of surface, applying under coat and finish coat of varnish over a filler coat of complete all as specified and directed by Engineer-in-Charge

Dismantling timber scantlings any type and over in section, in any position, Framed work complete all as specified and directed by Engineer-in-Charge.

IInd class Hard-wood, timber fixed and clean sawn, in scantlings complete all as specified and directed by Engineer-in-Charge

Dismantling wall, ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs any thickness, including cover fillets complete all as specified and directed.

False ceiling with 12mm thick gypsum board of size 595mm x 595mm including nitrile rubber sheet on and including standard GI snap grid, framed and suspended with 4mm dia wire including clips etc in patterns as approved by GE, in panels of size 605mm x 605mm (GI snap grid consisting of 1mm thick standard GI sections i.e. channel, angle, tee etc for intermediates, parameters etc) supported with 1mm thick standard GI section, fixed in ceiling with necessary fitting and fixtures as per manufacturers instructions and applying two coats of oil bound distemper including priming coat and preparation of ceiling surfaces, complete all as specified and directed.

Demolition of PCC in ground floors and pavings not exc 15 cm thickness (below or above GL) complete all as specified and directed.

75mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate, casted in panels as in plinth protection finished even and smooth w/o using extra cement complete all as specified and directed.

Preparation of steel and iron surfaces of any description over 10 Cm width or girth not otherwise described and applying two coats of synthetic enamel paint in comouflage pattern over a coat of red oxide primer on newly untreated surface as per site requirement as approved by GE complete all as specified and directed as specified.

Dismantling wrought iron or mild steel work of any description and in any position complete all as specified and directed by Engineer-in-Charge.

Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410 -W (GdeE- 250) quality A, complete all as specified and directed.

Mild steel work as in wind ties for roof including all necessary drilling, bolting or riveting etc and nosing to steps including embedding in concrete and securing etc conforming to Fe - 410 - 0 complete all as specified and as directed.

Two coats of synthetic enamel paint over a coat of red oxide primer on newly untreated surface of steel exceeding 10cm in width / girth including preparation of surface complete all as specified and directed.

Preparation of new wood or wood based surface and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes(any type), jointed in cement mortar and taking out trenches, complete all as specified and as directed by the Engineer-in-Charge

100 mm dia cast iron sand cast pipe waste or vent pipe in any length with or without ears with lead joint fixed to wall complete all as specified and directed by Engineer-in-Charge.

75 mm dia cast iron sand cast pipe waste or vent pipe in any length with or without ears with lead joint fixed to wall complete all as specified and directed by Engineer-in-Charge.

100 mm bore of pipe cast iron bends (any radius) diminishing pieces or traper (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

75mm bore of pipe cast iron bends (any radius) diminishing pieces or traper (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

100 mm branch pieces, single (equal or unequal)ordinary or inverted (spigot or socket type) or with parallel branches with oval access doors complete all as specified and directed by Engineer-in-Charge.

75 mm branch pieces, single (equal or unequal)ordinary or inverted (spigot or socket type) or with parallel branches with oval access doors complete all as specified and directed by Engineer-in-Charge.

Taking down old unserviceable/deteriorated batten/PVC conduit point wiring from existing place i.e. light, fan, socket or power points complete with all unserviceable fittings such as switches, sockets, ceiling rose, pendants, Holders, etc and making good all disturbed surface to wall, floor etc by means of cement mortar (1 : 3) or plaster of Peris and to match / finish new surface as the existing surface either by using same colour distemper, Putti or white / colour wash all as required and directed by Engineer-in-Charge.

Taking down main switch/DB/ changeover/AC box of any capacity including fixing accessories of single/three phase

Surface point wiring on wall , ceiling/roof with necessary fixing arrangements with PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 19 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and bakelite laminated sheet 3mm thick ISI marked for fixing of switches / sockets, fan regulators, wall mounting fittings, door bell & bulkhead/telephone socket etc with MS screw and cup washers including PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash with same existing colour surfaces all as specified and directed by Engineer-in-Charge for One light, fan, call bell point controlled by one switch.

All as per Item No 74 Above but for One 5 Amp socket point controlled by one switch on same board

All as per Item No 74 Above but for 5 Amp independent socket point controlled by one switch.

All as per item No 74 here-in-before but for power point wiring with 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead.

Switch flush type single pole one way 5 Amps, 240 volts, white finish, ISI marked complete all as specified .

Switch flush type single pole one way 15 Amps, 240 volts, white finish, ISI marked complete all as specified .

Socket outlet 5 pin, 5 Amps, 240volts flush type white finish , ISI marked complete all as specified.

Socket outlet 2 in 1, 3 pin, 5 &15 A, 240 volts, flush type white finish, ISI Marked complete all as specified.

Ceiling rose, surface backlite, 65 x 20 mm three terminal ISI Marked complete all as specified.

Lamp holder insulated body with back plate suitable for angle / batten fitting ISI Marked complete all as specified and directed.

Sheet metal enclosure VTPN MCCB DB 4way, 415 V (vertical type) with bus bar double door type IP 43 - IK 09 for DB when MCBs & MCCB 160 Amps (as incomer) to be used, fixed properly on / in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs for cables/wires all as directed.

Double door metallic sheet metal enclosure for DB when MCBs to be used SPN 8 ways, 240 V with 200Amps rated bus bar complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires all as directed.

Double door metallic sheet metal enclosure for DB when MCBs to be used SPN 4 ways, 240 V with 200Amps rated bus bar complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires all as directed.

Supply and fixing in repalcement MCB SP 240 volt 6 Amp to 40 amp 10 KA capacity having C-curve characteristics connected with suitable lugs.

Supply and fixing in repalcement MCB SPN 240 Volts 16 to 32 Amps 10 KA capacity having C-curve characteristics connected with suitable lugs.

Supply and fixing in repalcement MCB SPN 240 Volts 40 to 63 Amps 10 KA capacity having C-curve characteristics connected with suitable lugs.

Supply and fixing in repalcement MCB TP 415 Volts 40 to 63 Amps 10 KA capacity having C-curve characteristics connected with suitable lugs.

MCCB 160 Amps, 3 Pole, 415V, adjustable type with breaking capacity 36 KA complete all as specified and directed.

Sheet metal enclosure , 20A single pole and neutral with a two pin and earth plug and socket complete in metal clad board (Industrial type) with one single pole MCB 32 Amp fixed properly complete all as directed by Engr-in-Charge

Sub main wiring with two single core PVC-FRLS insulated unsheathed multi stranded copper conductor cable of size 6 sqmm drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 19 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc laid in concealed position with 6 Sqmm PVC-FRLS insulated unsheathed multi stranded copper conductor as a continuous earth wire including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash with same existing colour surfaces all as specified and directed by Engineer-in-Charge. One RM of Two 06 Sqmm copper conductor cables and PVC conduit combined shall comprise of one unit RM

Sub main wiring with four single core PVC-FRLS insulated unsheathed multi stranded copper conductor cable of size 10 sqmm drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 32 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc laid in concealed/surface position with 10 Sqmm PVC-FRLS insulated unsheathed multi stranded copper conductor as a continuous earth wire including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash with same existing colour surfaces all as specified and directed by Engineer-in-Charge. One RM of four 10 Sqmm copper conductor cables and PVC conduit combined shall comprise of one unit RM

LED bed light 3 watt, 240 volts suitable for mounting on wall surface including mounting accessories and making electric connection complete all as specificed and directed by Engr-in-charge

M&L recess mounting LED luminaries 35/36 Watt(2'x2'), 240 volts with more light distribtuion and clutter free ceiling with powder coated CRCA sheet steel white powder coated housing with square in a perforated metallic frame complete all as specified and directed.

Decorative ultra slim linear LED lighting fixtures with extruded polycorbonate envirnmental friendly energy saver LED light fitting 1x20/22 watt (4'), 230 Volts, single tube mounting including LED Tube 20/22 Watt complete with electronic driver spring loaded rotor type lamp holder, end cover, connector box etc and accessories, prewired, LED including required fixing arrangements and electrical connection three core copper cable from ceiling rose to led light fitting complete all as specified and directed

Decorative ultra slim linear LED lighting fixtures with extruded polycorbonate envirnmental friendly energy saver LED light fitting 1x10/12 watt (4'), 230 Volts, single tube mounting including LED Tube 10/12 Watt complete with electronic driver spring loaded rotor type lamp holder, end cover, connector box etc and accessories, prewired, LED including required fixing arrangements and electrical connection three core copper cable from ceiling rose to led light fitting complete all as specified and directed

Supply and fix, installing and testing ISI marked, metalic body, energy efficient, water heater storage type, copper tank, electgrically operated, single phase, 50 Hz (5 star rating), complete of 50 Ltr capacity with and including supply and fixing, wire armoured 450mm long, 15 mm dia brass coupler etc, flexible pipe suitable to withstand upto 100 degree celcius for hot and cold water, Anchor fastner - 04 Nos of suitable size , 3 core PVC insulated, FRLS multistranded copper conductor cable and plug top 15 Amps capacity complete in all respect and all as specified and directed by Engr-in-Charge.

Supply and fix heavy duty exhaust fan 300 mm sweep, metallic body, single phase 230 volts 50 Hz AC, 1400 RPM, totally enclosed heavy duty motor with die cast alumn rotor mounted on two ball bearings complete with louvers & shutters, including cutting chases and making circular holes for fixing exhasust fan to wall making good the distrubed surfaces to match with the existing specification, connecting electrically using 3 core 0.75 sq mm PVC insulated flexible copp-er conductor cable over all sheathed all as required at site or directed by Engr-in-Charge.

MCCB 4 pole 63 Amps 50 Hz, 415 Volts with rupturing capacity 25 kA with enclosure complete all as specified and directed by Engr-in-charge

LED Lamp 10 watt, 240 volts complete all as specified and directed.

Earthing complete with M.S. galvanized earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below normal GL) with top edge of the earth plate not less than 1.5M below normal GL, connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts & washers of GI or steel incl excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 15 mm dia light grade GI protection pipe, funnel with wire mesh,watering pipe of size 20 mm dia med. grade, lugs, main Earthing lead upto 7.5 mtr incl. Charcoal dust, salt etc. all as shown in electrical plate No. 3 of SSR Pt-I, 2009 specification. Note : Result of the earthing should be less then 4 ohms if not achieved the new earthing to be carried out without any extra cost.(Three Times)

Surface excavation not exc (not exceeding) 30 cm deep and averaging 20 cm deep and getting out in hardt/ dense soil complete all as specified and directed.

Excavation over areas not exceeding 1.5m deep and getting out in hard/dense soil, complete all as specified and directed

Excavation over areanot exceeding 1.5m deep and getting out in soft/disintegrated, complete all as specified and directed.

60 mm Thick Rubber moulded Machine pressed precast concrete interlocking paver block glossy finished with grey cement and pigment any shape and size confirming to IS 15658-2006 of , M-35 Grade laid over and including 50 mm thick sand cushioning, complete all as specified and directed.

75 mm thick Cement concrete type D2,1:4:8 (40mm graded crushed stone aggregate) as in sub base finished even and rough, complete as as specified and directed by Engineer-in-Charge

100 mm thick Cement concrete type B2,1:2:4 (40mm graded crushed stone aggregate) as in sides of interlocking tiles even and rough, complete as as specified and directed by Engineer-in-Charge

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete as as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in Hard/Dense soil, complete as as specified and directed

Rubber Moulded Colour chequered cement concrete tiles size 300x300x22 to 25mm thick, set jointed and pointed in neat cement slurry in floors, with grey cement and no pigment complete all as specified and as directed by the Engineer-in-Charge

Screed bed or bedding layer of mortar 15mm thick in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Brickwork with subclass `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge

PCC 1:4:8 Type D2 40mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

Walling of random rubble stone masonary, uncoursed, well bonded, bedded in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge. PCC Bond stones shall be used and quantity of bond stones shall be deducted from stone masonary. PCC bond stones shall be measured and paid seperately.

PCC 1:3:6 Type C1 (20 mm graded crushed stone aggregate) as in wall or retaining wall, any thickness, size or shape including pilasters buttresses columns, pillars boundary pillars and posts (including caps and bases) complete all as spefcified and as directed by the Engineer-in-Charge.

PCC 1:2:4 type B1 using (20 mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

PCC 1:2:4 type B1 using(20 mm graded crushed stone aggregate)as in walls, retining walls, basement walls, ballast walls and the like, any thickness, above top of footings, including attached pilasters and buttresses complete all as specified and as directed by the Engineer-in-Charge

Mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge.

Formwork to sides of concrete foundations, footings, bases of columns, raft and beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter, work in rough finished flat surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses etc, verical or to batter, work in rough finished flat surfaces of concrete complete all as specified and as directed by the Engneer-in-Charge

Rendering 20mm thick cement plaster in CM (1:4) on brick or concrete surfaces finished and smooth without using extra cement complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length of 110mm bore with rubber ring joints, laid in walls , complete all as specified and directed.

PCC type C1, 1:3:6 (20mm graded crushed stone aggregate) as in coping apex stone, bed plate etc complete all as specified and directed.

Broken stone or boulders hand packing ( any thickness) at back of walls over arches etc and raising (or lowering) to the required level complete all as specified and directed.

Providing pre cast bond stones cement concrete 1:2:4 type B1 (20mm graded crushed stone aggregate) set in CM 1:6 for stone masonary walling etc complete all as specified and directed.

Preparing new plasterted/unplastered surfaces and applying two coat of cement based paint on walls complete all as specified and directed..

Earthing complete with copper earth plate electrode 60cmx60cmx 3.15mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth strip of size 20x3mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point,duly protected with 40 mm bore light grade pipe up to main board, 20 mm bore watering pipe light grade with CI/MS funnel and wire mesh including excavation with having pit and cover in PCC 1:2:4 type B-1 including angle iron fram made of angle iron of size 40x40x6mm grouted in PCC pit for pcc cover all as specified and directed

Earth continuity copper conductor or main earthing lead of size 20x3.15mm fixed to screew etc wall with saddle/insulator PVC clitting (as per sample) or recess or chases or buried in ground or drawn in conduit/pipe or fixed to pole/roof or any other indicated situation for loop earthing etc. as required.

Earth continuity or main earthing lead of size 25 Sqmm single core copper conductor overall sheathed multistrand cable fixed on wall with saddle/insulator PVC clitting or recess or drawn in conduit/pipe or fixed to pole/roof or any other indicated situation for loop earthing etc. as required at site.

Air termination single pointed copper rod 12mm dia and 600mm long complete all as specified and directed.

Test point terminal block made of gun metal or phosphorus bronze of size 75X75X6mm drilled and screwed includind 03 Nos 8mm dia 25mm long hex. head screw complete all as specified and directed. .

GI pipe light grade of size 20 mm bore for laying in trenches/floors or walls including all fittings for fixing complete as required and directed by Engineer-in-Charge including taking down old unsv complete all as specified and directed..

GI pipe light grade of size 40 mm bore for laying in trenches/floors or walls including all fittings for fixing complete as required and directed by Engineer-in-Charge including taking down old unsv complete all as specified and directed..

Excavation in trenches in soft/loose soil not exceeding 1.5 m wide and n.exc 1.5 mtr in depth for laying of GI pipe and getting out complete all as specified and directed

Returning filling in including spreading leveling watering and well ramming in layers not exc. 25cm in soil , complete all as specified and directed

Removal of excavated material to a distance not exc 50m and depositing where directed at a level not exceeding 1.5mtr above starting point complete all as specified and directed.

Taking up or down steel tubing of 20mm to 50 mm bore and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete with all fittings & valves etc. (Excavation shall be measured and paid separately under relevent items) complete all as specified and directed

GI tubes medium grade galvanized with all fittings laid in trenches of size 20mm bore dia complete all as specified and directed.

GI tubes medium grade galvanized with all fittings laid in trenches of size 25mm bore dia complete all as specified and directed.

GI tubes medium grade galvanized with all fittings laid in trenches of size 50mm bore dia complete all as specified and directed.

M & L in replacement of Gun metal globe or gate valve iron wheel head, screwed both ends for iron pipe of bore of 20 mm complete all as specified and directed.

M & L in replacement of Gun metal globe or gate valve iron wheel head, screwed both ends for iron pipe of bore of 25 mm complete all as specified and directed.

M & L in replacement of Gun metal globe or gate valve iron wheel head, screwed both ends for iron pipe of bore of 50 mm complete all as specified and directed.

M & L Lagging to pipes all around with 40 mm thick bonded mineral wool performed `SNAP ON` pipe section of density 144 Kg/cum and provided with chicken mesh wire netting 25 gauge,20 mm mesh on pipe of internal dia 25 mm including rendering cement plastering 15 mm thick (1:3) on top layer of lagging all as specified & as directed by Engineer-in-charge.

M & L Lagging to pipes all around with 40 mm thick bonded mineral wool performed `SNAP ON` pipe section of density 144 Kg/cum and provided with chicken mesh wire netting 25 gauge,20 mm mesh on pipe of internal dia 50 mm including rendering cement plastering 15 mm thick (1:3) on top layer of lagging all as specified & as directed by Engineer-in-charge.

Construction of valve pit brick masonry, internal size 600x600x6900mm(from top of PCC to bottom of cover) including excavation in any type of soil, returning, filling around foundation , removal of surplus soil to a distance not exceeding 50m, PCC 1:4:8 type D2 in foundation, brick work in cement mortar 1:6, 6mm thick plaster in cement mortar 1:4 to internal & External surface of covered pit with MS sheet 03mm thick with locking arrangement handle fixing arrangement and painting with black oil paint two coat over a coat of red oxide primer all as specified and as directed.

Supply, laying testing and connecting 95 Sqmm 3.5 Core XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured heavy duty electrical cable with aluminium conductor, 1100 volts grade laid in trenches/ducts/wall or through pipe with suitable size of cable glands, criping type cable lugs complete all as specified and directed by Engr-in-Charge.

Sand cushioning 8 cm before laying HT/LT underground cable in trenches and 15 cm after the cable is laid and all as specified and directed by Engr-in-charge. Note:-The laid sand shall be gently punned down by hand to 18 cm depth.The punned thickness only shall be measured and paid.

Brick protection with well burnt sub class ‘B’ brick abutting each other( width wise) across the cable laid in trenches complete and all as specified.

GI pipe light grade of size 50 mm bore for laying in trenches/floors or walls including all fittings for fixing complete as required and directed by Engineer-in-Charge including taking down old unsv complete all as specified and directed..

S & F on load changeover switch in sheet encloser side handle AC 415 volt, four pole of capacity 125 amps complete all as specified and directed.

1100 volts grade heavy duty cable PVC insulated aluminium staranded conductor , served with inner sheathed PVC tape and overall PVC sheathed in service connection one twin core flat or circular of size 16 sqmm x 2core complete all as specified and directed.

Havish Construction

M/s. Rishav Sood

AV ENTERPRISES

M/S Ajay Kumar Mahajan

M/s Khajuria Construction Co.