Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹2.0 CrAccepted-AOC | ₹2.0 Cr | L1 | Accepted-AOC Quoted Lower than the Estimate Rate |
| 2 | L2₹2.1 CrRejected-Finance | ₹2.1 Cr | L2 | Rejected-Finance Quoted 7.28 percent Above the Estimate Rate |
| Sl No | Description | Qty | Unit | SRI RANGAVILAS INFRA TECH L1 | G V CONSTRUCTIONS L2 |
|---|---|---|---|---|---|
| 1.00 | Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers. Foundation | 325 | m3 | 265 ₹86,125 | 276 ₹89,700 |
| 2.00 | Earth work open excavation by manual means in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification and as direct-ed by the departmental officers. | 40 | m3 | 113 ₹4,520 | 118 ₹4,720 |
| 3.00 | Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. | 30 | m3 | 1,710 ₹51,300 | 1,785 ₹53,550 |
| 4.00 | Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers -Mixing by mechanical means | 65 | m3 | 5,389 ₹3.5 L | 5,624 ₹3.7 L |
| 5.00 | Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam & Footing | 375 | m2 | 707 ₹2.7 L | 738 ₹2.8 L |
| 6.00 | Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid). | 204 | m2 | 1,115 ₹2.3 L | 1,164 ₹2.4 L |
| 7.00 | Supplying and erecting centering for plane surfaces such as RCC Floor/Roof beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting above 3.60m upto 4.90m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m (expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2.40 x 3.0m (expandable upto 4.90m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c and with Cross bracings provided at two levels at a spacing of 1.80m etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid). | 69 | m2 | 1,207 ₹83,283 | 1,260 ₹86,940 |
| 8.00 | Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specifcation. Steel Adjustable telescopic props shall be rovided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid). | 348 | m2 | 642 ₹2.2 L | 670 ₹2.3 L |
| 9.00 | Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid). | 355 | m2 | 966 ₹3.4 L | 1,008 ₹3.6 L |
| 10.00 | Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting above 3.60m upto 4.90m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2.40m x 3.00m (expandable upto 4.90m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) with Cross bracings provided at two levels at a spacing of 1.80m ,etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers (Payment for centering shall be given after the concrete is laid). | 152 | m2 | 1,024 ₹1.6 L | 1,069 ₹1.6 L |
Tender Value
₹2.0 Cr
EMD Value
₹2.0 L
Closing Date
7 Jan 2026, 3:00 pmClosed
Commissioner, Rasipuram Municipality
72, Bharathithasan salai, Rasipuram Municipality
Construction of Knowledge centre Ward - D,Block No - 8,Survey No - 1/2(Part) in RASIPURAM MUNICIPALITY.
2025_MAWS_635751_1
2219/2024/E - knowledge
Open Tender
Civil Works
Rasipuram
Refer Tender document
2 documents required · 2 mandatory
₹10,000
₹2.0 L
Yes
Municipal Office, Rasipuram
20 Feb 2026
24 Dec 2025
7 Jan 2026
24 Dec 2025
7 Jan 2026
24 Dec 2025
30 Dec 2025
Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers. Foundation
Earth work open excavation by manual means in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification and as direct-ed by the departmental officers.
Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.
Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers -Mixing by mechanical means
Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam & Footing
Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).
Supplying and erecting centering for plane surfaces such as RCC Floor/Roof beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting above 3.60m upto 4.90m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m (expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2.40 x 3.0m (expandable upto 4.90m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c and with Cross bracings provided at two levels at a spacing of 1.80m etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).
Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specifcation. Steel Adjustable telescopic props shall be rovided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).
Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).
Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting above 3.60m upto 4.90m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2.40m x 3.00m (expandable upto 4.90m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) with Cross bracings provided at two levels at a spacing of 1.80m ,etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers (Payment for centering shall be given after the concrete is laid).
Providing and laying in position, standardised concrete Mix M-20 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without inspiring strength and durability with about (5 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost ofreinforcement grill and fabricating charges, centering and shuttering and also including laying,vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc.,complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).
Upto basement
Above basement
For first floor
Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550 D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire)
For 1 Qtl - upto plinth/Basement level:
Ground floor Below Ground level of every 3.50m depth.
First floor (second 3.50mdepth.)
Supplying and filling in foundation, basement, etc with conveyed earth in layers of not more than 150mm thick layers well watered, rammed with surface vibrator and consolidated including conveyance charges etc. complete complying with standard specification and as directed by the departmental officers.
Brick work in following Cement Mortar using best quality Fly ash Brick of size 230x110x75mm with class designation of 10 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge. for Basement
For Basement
for Super structure in Ground floor
First floor
Brick partition walls of 11.50cm thickness using best quality Fly ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)
Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.
Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including mortar plasticizer at 200ml per 50Kg of cement used , hacking the surfaces and curing, etc., in all floors complying with standard specification and as directed by the departmental officers
Supplying and Fixing of Fully Panelled Doors - External or Internal Moulded Planks Single Leaf 800 X 2100 Type ‘B’ - (Unequal Panels) Etc, Complete Complying With Standard Specification and as Directed by the Departmental officers.
Supplying and fixing solid core flush shutter of following type with thickness and necessary T.W. internal lipping alround conforming to IS 2202-1(1999) including cost of wind appliances and furniture fittings such as 3 Nos of SS 304 Grade Parliament Hinges of Size (125mm x 150mm) , 2 Nos 300x12mm aluminium tower bolt 1 No. 200x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 2 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete complying with standard specification and as directed by the departmental officers - Single leaf.
Supplying and Installing Metal False Ceiling using Fire Retardant Galvanized Steel Sheet Plain lay in tile size 600mm x 600mm, 0.5mm thick, powder coated on external surface and shall have flange on all four sides to rest on the exposed grids. The system to give 600mm x 600mm centre to centre 'T'. The 'T' shall be not be dipped GI Tee Section 3600mm long main Tee. 24mm wide and cross Tee panels are formed by running main runner of 'T' section of size 30mm x 24mm powder coated at bottom at intervals with powder coating at bottom. Necessary provision of inter locking of 'T' section are made at required intervals not exceeding 1200mm. The main runners are suspended from the ceiling by means of 4mm dia. GI rods fixed to the ceiling using anchor fasteners of 50mm x 8mm size with nylon inset and hooked to the main rubbers using clips. The last hangers at end of each rubber should not be greater than 600mm from the adjacent wall. The last panel shall be placed at the side wall using edge profile 'L' Angle of size 20mm x 20mm and fixed to the side wall the false ceiling should be fixed of same level and should present a neat look (SOR 2025-2026 M-0689)
Dadooing walls with following best approved quality, white / colour glazed tiles conforming to IS 15622 of 300 x 200 x 6mmsizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)
Flooring with ceramic tiles of following size and variety conforming to IS 15622 laid over cement mortar bed of 20 mm thick in cement mortar 1:3 (One Cement and Three crushed stone Sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)
Paving the floor with best quality vitrified Tiles of 600x600x8mm size and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)
Painting New Plastered Wall Surface with Two finishing coats of ready mixed (Emulsion) of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)
Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.
Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete(M-0651)
Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers.etc., complete as per standard specification.
Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete as per standard specification.
Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with One coats of best approved first quality and colour of synthetic enamel paint over the priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)
Supply and fixing of Stainless steel (Salem stainless steel) Door frame ( Box section using stainless steel plate of 1.6mm thick) of size 100mm X 60mm with a rebate of 30 / 35mm X 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel holdfast etc.
Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 25GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with spag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown olour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the executive Engineer before use on work (PWD SOR Sl.No 65, P.265)
Supplying and fixing UPVC (Un-Plasticized PolyvinylChloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work (PWD SOR Sl.No 65, P.266)
Providing and laying, spreading and compacting graded stone aggregate to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.
Supplying and laying of Interlocking Paver Block Stone 63mm thick Over a base layer of crushed stone sandfilling incl. Cost of materials laying and Labour charges etc complete complying with the standard specification and as directed by the departmental officers.
Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification
Supplying , fixing and roofing with colour galvalume sheet of 0.47mm thick with all necessary accessories such as J/V bolt and nuts of suitable length with suitable bitumen washers complete complying with standard specification and as directed by the departmental officers.
Supplying and fixing of ball valve with, bolted bonnet, inside screw, non rising spindle, conforming to IS : 14846 (Sluice valve)/ASTM A105 (Ball valve) - (PN – 10.0) etc. including necessary fittings & testing of valve joints complete as per direction of Engineer in Charge (pg.317 TWAD) - 25 mm nominal bore
PVC Pipe (Un-Plasticized Polyvinyl Chloride) UPVC used for residential and home applications, water pressure in residential areas do not normally exceed the maximum tolerance. (Schedule-40)
20mm dia
25mm dia
Sanitary works
Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm P or S trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections,15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and redoing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting
Supplying and fixing of position of Indian make white glazed earth were wash basin 550mm x 400mm with all accessories such as cost Iron brackets, 32mm dia C.P. Waste coupling, Rubber plug and chain, 32mm dia 'B' class, G.I. Waste pipe, 15mm dia, G.M.Wheel valve, 15mm dia Nylon connection, 15mm dia Brass Nipples, 15mm C.P. pillar tap etc.,
Supply and fixing in position of brass chromium plated screw down Tap 15 / 12mm Dia (Heavy Type) with necessary accessories, , etc.complete complying with standard specifications and as directed by the departmental officers.
Supply and fixing in position of chromium plated stop cock 15mm Dia with necessary accessories, , etc.complete complying with standard specifications and as directed by the departmental officers. (M-0512)
Supply and fixing in position of Porcelin soap dish of size 150mm x 150mm x 50mm with necessary TW plugs, clamps, screws, etc.complete complying with standard specifications and as directed by the departmental officers. - PWD - pg.55
Supply and fixing in position of brass chromium plated towel rail 60cm long and 20mm dia with Brackets with necessary TW plugs, clamps, screws, etc.complete complying with standard specifications and as directed by the departmental officers.
Supply and fixing in position of PVC / Fibre Glass framed 5.5mm thick mirror, shelf type with Hard Board Backing with necessary TW plugs, clamps, screws, etc.complete complying with standard specifications and as directed by the departmental officers.
Supply and fixing in position of Cast Iron Nahini / Floor Trap with stainless Steel Grating with necessary accessories, , etc.complete complying with standard specifications and as directed by the departmental officers.
Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 40 mm pipe 6Kgf/cm2
Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2
Supplying and laying the following dia un plasticized PVC pipes 6KSC & 10 KSC confirming to IS 4985/2000 and relevant specials including packing the joints with rubber /lubricant fixing ,holding wherever necessary and making good of the dismantled portion with necessary connections etc., complete as directed by engineer in charge.
75 mm dia
110 mm dia
Pipe Excavation
Excavating trenches of required width for pipes including excavation for sockets, refilling.and dressing of sides, ramming of bottoms, depth up to 1.1m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :
Earth work (other than loose soil) for HDPE / PVC / GRP pipe
40 mm dia to 160 mm dia - (0.60 m width, 1.05 m depth) -WD-W0700
Supply and fixing of Precast RCC(M30) Bio septic tank of 2.25KLD consists of three chambers - sedimentation chamber,Bioprocessing chambe with PP flower media(virgin plastics bio balls) & settling chamber which shall be coated inside and outside of tank with PU paint for extended life of tank up to 25 years. 2nos of manholes of 500mm shall be provided for easy and safety service. Bio-enzyme shall be used which consists of 20 different types of enzymes and bacteria which can develop in both aerobic and anaerobic conditions and this will start to reduce the BOD and COD of the sewage water and the water will loses its hardness during this process and neutralizes the PH between 6.6 to 7.5. The settled sludge shall be self-digestive. Treated water is orderless and colorless and shall be discharged to Garden/Choke pit/connected to existing sewer line. (Q)
Borewell - According to the site condition
Providing Geophysical survey incuding all and conveyance,etc., complete
Drilling of 150mm dia bore well Over burdan soils in hard rock areas anywere in Tamilnadu icluding transportation to the work site in hard rock areas and developing the bore wells etc., complete as per the standards specifications.
up to 150mm
above 151 up to 180
above 181 up to 210
above 211 up to 240
Supply and delivery of 200 mm dia PVC Plain casing pipe etc., complete.as per standard specification WD- M1418
Supply and fixing of 1000 lit HDPE Tank ISI make with all accessories such as Tank Nipple, Washer etc,including cost and conveyance of all materials to site etc, complete as per standard specifications. WD-M1418
Supplying and erecting in position of 250 liters capacity Industrial Model Reverse Osmosis Water-cumPurifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20 Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact. PWD -M-0721
Supply and delivery of clear water vertical wet type submersible pump conforming to IS 8034/2002 and as amended thereafter and BEE 3 Star Rated capable of discharging 15x125 LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor suitable for operation in AC single phase 230 V+/- 10 %,50 HZ +/-5 % 20LpmX125m head submercible pump set of ISI make - pg.102 TWAD -WD-M1597
Supply and delivery of direct online starter confirming to IS13947, IEC60947-1 and as amended thereafter with suitable KW rating for operation in AC/single Phase/50HZ(± 5%) and 230 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16 Amps 2 pole Magnetic Contactor with under Voltage protection, Indication lamp, starting capacitor, running capacitor and On/Off Push button switches, 5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulated cable, powder coated vermin proof box including the capacitor (the cost of capacitor is to be taken separately).1.5HP pannel board -WD-M1906
Supply and delivery of MS Kiosk of size 0.75m x 0.45m x 0.75m made up of MS angle of size 50mm x 50mmx 4mm alround covered with 16 gauge MS sheet and kiosk door made up of MS plates of size 25 mm x 3 mm including cutting, welding, grinding, locking arrangements and labour charges etc., -WD-M1471
PVC Insulated And Sheathed 3 Core Flat Type Copper Cable Conforming To Is 694/1990 And As Amended Thereafter 4 Sqm 3 Core Copper Cable Wd-M1975
40mm HDPE PIPE FOR SUB-MERSIBLE PUMP IN BOREWELL Class-5 (1 MPa or 10 kg./cm2 pressure) M-1057
Supply and delivery of following pipes and specials including cost of all charges etc., complete as per standards specifications.
32 mm dia GI hex nipple -WD-M0599
32 mm GI pipe -WD-M0487
32 mm dia GM NRV (Q)
32 mm dia GI union WD-M0603
12 mm dia nylon rope- M-1072
Bore cap using M.S. Flat of size 1 cm x 3mm and M.S. sheet on top with bolting arrangements for securing the cap in position (Bore caps with M.S. Couplings need not be made) -8 “ Casing Pipes - WD-W0738
32 mm x 20 mm dia GI reducer -M-0476
20 mm dia GI coupling -M-0468
32mm dia GI Coupling -M-0466
Supply and delivery and fixing of HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc., - 1000 litre HDPE tank - WD - W-M1418
32 mm dia PVC pipe (10Kg/sqm) -M-0877
32 mm dia PVC tee -M-0901
32 mm fuse carrier -M-1392
32 A MINIATURE CIRCUIT BREAKERS 240 V / 415V 50HZ - AC SUPPLY SUITABLE FOR BOTH LIGHTING AND MOTOR CIRCUITS - Single Pole & Neutral -HIGHER END -M-1763
40mm dia PVC pipe -M-0878
40mm dia PVC Coupler-M-0884
40mm dia PVC Elbow -M-0890
40mm dia PVC Tee -M-0902
Electrical Works
Supply, installation testing and commissioning of 3Ph EB Service panel & all necessary protection as per TNEB standard, including all fuse unit, EB meter shall be suitable for utilizing excess power from Solar panel, 40A DP MCB - 1 No, 32A DP MCB-2 Nos
Wiringwith2x1.5sq.mm.PVCinsulatedSCunsheathedFRLScopperconductorof1100VgradeinsuitablePVCrigidpipeconcealedinwallandceilingwithPVCaccessoriesinflushwithwallwith3mmthickhylumsheetcoverwithTWswitchboxand5AFTswitchwithcontinuousearthwireconnectionof1.5sq.mmcopperwireformakinggoodoftheconcealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator). SD 23
Wiring with 2x1.5sq.mm.PVC insulatedS Cun sheathed FRL Scopper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mmx100mmx113mmTWswitch box with 3mmthick hylem sheet cover for 5A 3pinnon interlocking wall socket with 5A flush type switch with continuous earthwire connection of1.5sq.mm copper wire and making good of the concealed portion with suitable colour for concealed PVC plug point(SD-38)
Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 54
Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.SD 222
Supply and fixing of 32A TPNMC switch on incoming and 3 Nos. 32A DPMC switch (front handle) as outgoing with suitable adoptor box with suitable MS cable entry box trunking boxes and internal connections on suitable angle iron frame work with earth connection (SD. 156)
Supply and fixing of 4 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 No 32 A 4 P MCB as incoming and 12 Nos 6A to 32A SP MCB as outgoing on wall with Earth connection only. Lower End(SD. 538)
Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5m (SD.75)
Supply and run of 4x6sq.mm.PVC insulated SC unsheathed FRLS copper conductor of 1100V on 7/20 GI bearer wire for service connection mains (SD 68)
Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall (SD-114)
Wiring with 2 x 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor cable of 1100V grade in suitable pipe on wall and ceiling with PVC accessories with 150mm x 100mm x 113mm TW switch box for 15A 3 pin non inter locking wall socket with 15A flush type switch with painting of suitable colour with continuous earth wire connection of 4 sq.mm copper wire for open PVC power plug point .SD 39
Supply and laying of 2 x 10 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (SD 176)
Supply and fixing of brass cable gland for 2 x 10 sq.mm. PVC armoured LTUG cable with earth connection (SD 160)
Supply and fixng of TNEB meter board suitable for 3 phase 63A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 63A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with 1 No 63 Amp 30 MA Four Pole RCD / RCCB (Higher End) with suitable necessary connection with earth connection complete. SD 131
Supply and fixing of 32 A TPN MC switch on incoming and 3 Nos 32 A DPMC Switch (Front Handle) as outgoing with suitable adoptor box with suitable MS cable entry box trunking boxes and internal connections on internal connections on suitable AI frame work with earth connection etc, complete.SD 156
Supply and fixing of 16A TPN metal clad switch on suitable angle iron work with cable entry boxes for incoming and outgoing with PWD earthing -SD 145
Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonr. SD 221
Supply and run of 2 of 4sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG Cu wireand making good of the concealed portion with suitable colour (SD57)
Supplying and Laying of 3½ x 50 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 M putting 0.15 M layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. [ SD 166]
Supplying of 4 x 10 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 M putting 0.15 M layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. [SD 180 ]
Conveyance, installation, testing and commissioning of pre-wired 18 W LED 18W LED 3000K Square Type Recessed Fitting with LED suitable for Surface complete with all accessories etc. M-1285
Conveyance, installation, testing and commissioning of decorative type, 4mtr length, pre-wired hanging type 60 watts LED Tube Light complete with all accessories etc. directly on ceiling using 2 nos hanging rope of length 60 cm properly hooked to steel hooks anchored to the ceiling and giving connections with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connection etc. as required. (Q)
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2Nos x 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). (Q)
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 1Nos x 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). (Q)
SUPPLY & INSTALLATION OF AIR-CONDITIONER WITH COPPER COIL With 2.0 TR Split Type AC Unit - 5 Star Rated and Supply and installation of 5 KVA capacity Automatic Voltage Stabilizer with time delay relay and Supply and laying of 5/8” and 3/8” copper pipe (Extra beyond 3 metres supplied with AC unit) and Supply and fixing of MS stand for fixing outdoor unit(M-1985)
Supply and fixing of 1200mm sweep Ac ceiling fan with stepped electronic 300W regulator with the existing down rod on the existing clamp (SD -112)
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 1 Nos x 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
Furniture
Supply and delivery of HIGH BACK CHAIR with Executive ergonomic mesh chair with headrest in Black, 700mm Aluminum base, Adjustable lumbar for excellent back support, Height adjustable back with 5 separate positions, Adjustable tension control, Dual pivot mechanism, Multi-functional 3D adjustable arms, Full diamond mesh, Extralarge executive headrest, Heavy duty SHS gas lift, Waterfall seat, Maximum Weight limit - 150kg, Suitable for 24 hours use etc., complete
Supply and delivery of OFFICE CHAIR with Deluxe Mesh chair with folding Arms, Breathable Mesh Back, Air Flow Mesh Seat, Tilt Mechanism lockable in the upright position, Folding Arms, Heavy duty gas lift (110 kilos), Foam 2 and Fabric conform to BS5852 UK FR, W690 x D755 x H960 - 1060mm etc., complete
Supply and delivery of READING CHAIR with Seat Material –Fabric, Back Type - Mid Back Arm Type – Fixed, Arm Warranty - 1 Year, Brand - MBM Seating Height - 20 - 21 Inches, Color – Black, Height Adjustable – Yes, Seat Height Adjustable – Yes etc., complete
Supply and delivery of COMPUTER CHAIR with Low back chair with arms and plastic outer cover, Primary Material – Castors, Chair base, Gas lifter, chair arm, Press wood sheet, Plastic outer cover, Style – Modern, Finish – Fabric etc., complete
Supply and delivery of CHILDEREN’S CHAIR with Lightweight and easy to move, About $15 in materials to build each chair, Easy to build plan designed for a novice woodworker, Uses basic tools, Classic style can is beautiful painted or stained, Storage compartment is big enough for notebooks and more, Works with standard children's tables, Measurement - 0.42m X 0.33m X 0.55m etc., complete
Supply and delivery of CLASS ROOM CHAIR with Seat Material –Fabric, Back Type - Mid Back Arm Type – Fixed, Arm Warranty - 1 Year, Brand - MBM Seating Height - 20 - 21 Inches, Color – Black, Height Adjustable – Yes, Seat Height Adjustable – Yes etc.,complete
Supplying and fixing of Conference Hall - Half Round Table to site, by using of MDF (Medium Density Fiber) panel sheets for 15 nos of seating capacity, the cost including of material charges, required hinges at bottom support, nails, screws for joints and finish the top with Mica sheet, also including making and labour charges complete. (Total length(straight table) = 4.85m,Curve portion table length = 2.45m,Straight portion Table width = 0.70m,Curveature portion Table width = 0.90m) Note : Reading table may also be provided as study table on theatre type having 8 to 10 seats on either side of the table in rows to accommodate 30 seats for reading even during training session.
Supplying and fixing of System table with Key Board Rack to site, by using of MDF (Medium Density Fiber) panel sheets, the cost including of material charges, making charges ,Required hinges at bottom support, nails, screws for joints and labour complete. At computer Zone area tables based on number of computers. (Measurements for Computer tables, For each system cabin Length =0.90m,Width = 0.60m, Height of table top from ground = 0.76m,Cabin partition height from table top = 0.25m)
Supplying and fixing of Study Table with Cabin to site, Each cabin length = 0.90m,width = 0.60m, Height of table top from ground = 0.77m ,Cabin partition height from table top = 0.43m the cost including of all material charges, making charges, Required hinges at bottom support, nails, screws for joints and labour etc., complete
Supplying and fixing of Reception table with Fittings to site, by using of MDF (Medium Density Fiber) panel sheets, the table with the size of 2.20m x 0.60m and Height = 0.90m with Required trays and draws and Computer spaces as per site conditions.The cost including of material charges, making charges and labour etc., complete.
Supplying and fixing of Librarian table with Fittings to site, by using of MDF (Medium Density Fiber) panel sheets, the table with the size of 2.20m x 0.60m and Height = 0.90m with Required trays and draws and Computer spaces as per site conditions. The cost including of material charges, making charges and labour etc., complete.
Supplying and fixing of Manager Room Table to site, by using of MDF (Medium Density Fiber) panel sheets system fittings and keyboard section with the over all table size of 2.20m x 1.10m with Height = 0.77m to site with required trays and Draws at both sides, the cost including of material charges, making charges and labour etc., complete.
Supplying and fixing of Paper Display to site, By using of MDF (Medium Density Fiber) panel sheets the display furniture table size of 2.50 x 0.45m and Height = 1.23m with Magazine Bay opening Each = 0.25m at both sides ,the cost including of material charges, making charges and labour etc., complete.
Supplying and fixing of Book racks at Ramp side : (4.16m x 2.56m =9.81Sqm) to site, By using of MDF (Medium Density Fiber) panel sheets the cost including of material charges, making charges and labour etc., complete.
Supplying and fixing of Book racks at Ramp side of size 3.86m x 1.67m = 6.44 Sq.m, by using of MDF (Medium Density Fiber) panel sheets the cost including of material charges, making charges and labour etc., complete.
Supplying and fixing of Book self size 2.45m x 2.22m X 2.22m, by using of MDF (Medium Density Fiber) panel sheets the cost including of material charges, making charges and labour etc., complete.
Supplying and fixing of Children's Table to site for in bottom of OTS area, By using of MDF (Medium Density Fiber) panel sheet and also the table top should be finished with mica sheet of variant colour as per the instruction of Departmental officers, the over all table size of 1.00m x 1.00m to site With Height = 0.55m with seating capacity of 5nos (per each table) the cost including of material charges, making charges and labour etc., complete.
Supply, Delivery & Installation of Desktop (without display) with the following specification including cost of materials and labour charges for installing etc., Technical Specification : Processor - Intel Core i3 Processor (10th Generation Processor & Board) Ram & Storage - 4GB RAM/1TB SATA HDD with DVD Writer, Key Board & Mouse OS – Windows 10 SL
GENSET
Supply errection and commisioning of 25KV Genset of diesel capacity 50liter and automatic type of ISI Make including cost of concrete bed , errection and all other cost and conveyance etc complete -SOR - M-2345
Fire Fighting
Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers.(M-0851)
Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)
Supplying and painting the walls with two coats of cement paint as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications and as directed by the departmental officers. (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).
GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}
Please Enable Macros to View BoQ information
stage.html
html • 0.04 MB
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.34 MB
Techbidknowledge.pdf
Tender Documents • 0.66 MB
BOQ_760904.xls
BOQ • 0.46 MB
Download all tender documents and submit your bid