CO Raja Virbhadra Singh Ghat and Rejuvenation of Bawari at Shani Mandir near Gandhi Park in Urban area MC Rampur

Amount

Excavation in earth work and disposal of all excavated earth up to all leads and lifts, disposed earth to be levelled neatly dressed as per direction and to the entire satisfaction of the Engineer-in-Charge.

Excavation in earth work in chiesling /wedging out of Rocks where blasting is probihited, lift upto 1.50 mts. stacking the excavated soil not more than 3 metres clear from the edge of excavation within a lead of 20 metres complete in all respect as per entire satisfaction of Engineer in Charge.

Providing and laying cement concrete 1:5:10 ( 1 cement : 5 sand : 10 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinth complete in all respect with in all leads & lifts and as per the direction & to the entire satisfaction of the Engineer-in-Charge.

Providing and laying cement concrete 1:4:8(1Cement: 4Sand: 8Graded stone agg.40mm nominal size)& curing complete excluding cost of form work in foundation and plinth as per direction & to the entire satisfaction of the Engineer-in-Charge with in all leads and lifts .

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size)

Column, Piller Post and Strut and Plinth Beam and Beam

In suspended floor roofs ,landing and shelves and their support.balconies , beams,girders, bressumers and contilever up to floor two level with in all leads and lifts.

Providing and laying cement concrete work 1:1:2 (Nominal Mix 1 cement: 1.0 sand: 2.0 graded stone aggregate 20 m nominal size) and curing, complete in all respects & as per the directions of Engineer-In-Charge excluding cost of formwork in wall

In foundation & Plinth,base slab.

In wall any thickness

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centering, shuttering, strutting, and propping etc. with wooden battensand ballies, height of propping and centering below supporting floor to ceiling not exceeding 4.0metersand removal of the same for in situ -reinforced concrete and plain concrete work in;-

Flat surfaces such as soffits & suspended floors, roofs, landing and the like. Floor etc. upto 200mm in thickness.

Vertical surfaces such as walls ( any thickness ) partition and the like including attached pillasters buttresses, plinth and string courses and the like.

Column ,piller

Beams, cantilivers, girders and lintels sides and soffits of beams, beam haunchings cantilivers, girders, bressumers and lintels not exceeding 1 mtr. In depth.

Providing Tor steel reinforcement for RCC work including bending, binding & placing in position complete in all respects & as per the directions of the Engineer-In-Charge

Providing and laying in retaining wall and breast wall 10.0 Kgf/cm² working pressure unplasticized P.V.C. Pipes (Confirming to IS: 4985-2000) to make weep holes complete including making good the walls.

Stone/Boulder filling behind the retaining wall complete in all respects & as per the directions of the Engineer-In-Charge

Providing and laying 40 mm thick Fine sand stone / Red stone flooring over 20mm (average) thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of stone i/c rubbing and polishing complete.

Providing and fixing Cast Iron foundry made railing including all lead an lift as per entire satisfaction of Engineer-in-charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing decorative Yard lights incluiding all accessories i.e wire , switch & bulb etc as per entire satisfaction of Engineer in charge with in all lead and lift

Providing and supplying Cast iron 3 seater Garden bench for outdoor park weighing not less than 65 Kg with in all lead and lift as per entire satisfaction of Engineer-in-charge

Removing dry or oil bound distember by washing and scraping and sand papering the wall surface smooth including necessary repairs to scratches complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matt finish to the surface complete. including carriage of material within all leads and lifts as per direction of Engineer-in-charge.

Painting two coats on wall surfaces with Water proof anamel paint to give an even shade including cleaning the surface of all dirt, dust and other foreign matter and sand papering as required with in all lead and lift as per entire satisfaction of Engineer-in-charge.

Applying priming coat over new steel & other metal surfaces with ready mixed paint, brushing to give an even shade including cleaning of all dirt, dust and other foreign matter and sand papering and stopping

Painting two coats ( excluding priming coat) on new steel and other metal surface under coat with ready mixed brushing to give an even shade including cleaning the surface all dirt,dust and other foreign matter and sand papering and stopping as required with in all lead and lift as per entire satisfaction of Engineer-in-charge.

Wall Painting and Writing letters or figures on any surfaces with readymixed paint (stops, comas, hyphens and the like not to be measured and paid separately)Block letters/figures, Roman letters/figures, Italic letters/figures.

Brick work using common burnt clay building bricks in foundation and plinth in cement mortor 1:6 (1 cement: 6 sand), Ist class bricks

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position.2nd class deodar wood.

Providing and fixing panelled glazed or panelled and glazed shutters for doors, windows and clerestory windows, including black enamelled iron butt hinges with necessary screws 40 mm thick 2nd class deodar wood.

6 mm cement plaster in single coat on rough side of brick/stone masonry for interior plastering upto floor two level i/c arrises,internal rounded angles chamfers and/or rounded angles not exceeding 80mm in girth & finished even & smooth in C.M 1:4

20 mm cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering upto floor two levels inclduing arrises internal rounded angles, chamfers end/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortor 1:6 (1 cement: 6 sand)

White wasing with lime on decorated wall surfaces two coats to give an even shade including thoroughly brooming the surface to remove all dirt, dust and other foreign matters.

Cement concrete flooring 1:2:4(1 cement: 2 sand: 4graded stone agg. 20mm nominal size) laid in one layer finished with a floating of neat cement 40mm thick.

Applying priming coat on new wood and wood based surfaces after and incluidng papering the surface by thoroughly cleaning oil, grease, dirt and other foreign matters, sand papering and knotting, readymixed paint brushing wood primer pink.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint to give an even shade incluidng cleaning the surface of dirt, dust and other foreign matters sand papering and stoping with enamel paint other than white.

Providing and fixing anodized aluminium sliding door bolts with bolts and nuts screws etc. complete 250x16mm

Providing and fixing anodized Aluminium tower bolts (Barrel type) with screws etc complete 150x10mm

Providing and fixing anodized Aluminiumhandles with necessary screws etc. complete 125mm

Providing and fixing to wall ceiling and floor galvanised mild steel tubes ( MG) including fitting and clamps including making good the wall ceiling and floor complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge ..

15mm nominal size

Providing and placing (at all heights) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes including all fittings and float valve excluding the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license ]. 300 Ltrs. capacity complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Providing and fixing vitreous china wash, down water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement: 1 sand). Seat and cover to be measured and paid for seperately. Anglo Indian Universal closet.complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Providing and fixing plastic seat and cover for wash down water closet with C.P. brass hinges and rubber buffers: White plastic seat and cover, solid type.complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.10 litre capacity - White complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Providing and fixing PVC / G.I. inlet connection for flush pipe connecting with W.C. pan.complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Providing and fixing C.P. brass angle valve of standard design and of approved make, 15mm nominal bore. complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Providing and fixing C.P. water jet including connection pipe with check nut complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .

Providing and fixing PVC pipes of 10 Kg f/Sq.cm working pressure including fittings as per requirement at site complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .110 mm OD

P/Fixing pedestal Type Washbasin including all with in all lead and lift as per entire satisfaction of Engineer-in Charge

Roshan Chauhan (BID ID -532433)

MANOJ KUMAR (BID ID -532897)

RAHUL KAPATIYA (BID ID -532459)

Devender (BID ID -532443)

M/S KEDAR BHALUNI (BID ID -532319)