REPAIR TO ROOFING, JOINERY, PLUMBING, SANITARY WORK, FENCING AND DRAIN AT 41 WEU UNDER GE AIR FORES PATHANKOT.

Amount

Dismantling of asbestos cement corrugated or semi corrugated sheet in roof covering complete all as specified and directed by the Engineer-in-charge.

Dismantling of timber scantling 40 Sqcm and over in sec in any position as in framed work complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Pre- painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing steel tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed by the Engineer-in-charge.

Material and labour for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by the Engineer-in-charge.

Taking down Doors chowkat or frame exc 1.5 Sqm but not exc 4 sqm but with shutters (without taking off shutters from the frames) and removing out of site complete all as specified and directed by the Engineer-in-charge.

Taking down steel/wooden door window ventilators chowkat or frames n.exc 1.5 Sqm each. but with shutters (without taking off shutters from the frames) complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Pressed steel frames for doors size 125 mm X60 mm with one or more rebates including necessary fixing lugs, lock strike plate, etc. complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Pressed steel frames for doors size 105 mm X60 mm with one or more rebates including necessary fixing lugs,, lock strike plate, etc complete all as specified and directed by the Engineer-in-charge.

Material and Labour for PCC type C-1, 1:3:6 (12.5 mm graded aggregate) filling in door and frames, any size, single or double rebated, including arrangements complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Factory made single extruded WPC (Wood PolymerComposite) UV Coated solid plain flush door shutter of 32 to 35mm sizecomprising of virgin polymer of K value 58-60.(Suspension Grade), calcium carbonate and naturalfibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screwwithdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm², modulus ofelasticity 850 N/mm² and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing factory made fully guaged/ wire guage (single piece Bothside) PVC prelam door shutter 33-35 mm thick (style) consisting of framemade outmild steel tubes of size 19mm x 19 mm (19 gauge)top and19 mm (19 gauge) in styles.Single Pieces plainbottom. rails and 19mmcoloured PVC sheets 5mm thick to be used to cover styles and rails.PVCsheet strip of 20 mm width stuck inside with solvent cement for stiles & plaincoloured PVC sheets for top rail, lock raii and bottom rail on either side and asgap insert for top rail and bottem rail.Panel will be wire gauges and tightenfirmly. and fitted as per manufactures instructions including Stainless steelwire cloth, 0.25 mm: to 0.36mm nominal dia of wireaverage width ofaperture 1.40mm to 2mm and Aluminum XPM in rhombus shape, in one Piece from top rail to bottom rail complete all as specified and directed by the Engineer-in-charge.NOTE :- All screws shall be self tapping chrome plated.

Supply and fixing for factory made Steel window/ Ventilator 1.25mm thick box type (primer coated) ERW hollow P section of size 60mmx25mm including grill using 10 sqmm bar double rebated both gauge and glass shutter comprised gauged glazed Skelton shutter ERW sec 50mmx20mm and 1mm thick with two open able leaf consisting two Nos sash bar of T Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T Section of size 60mmx25mm and 1.25mm thick complete all as specified and directed by the Engineer-in-charge. following fitting welded to frame shutter : (a) Hold fast,150mm long of 12mmx3mm made to shape O4 Nos per window (b) handle of Z Sec20mmx25mm, 100mm long-per No leaf (c) MS Tower bolt 150mm long-02No per leaf . (d) Z section 20mmx25mm, 100mm long stopper 1 No per leaf. (e) cleat 55mm long of hollow square 15mmx20mmx63mm welded to hinge. 1 No per leaf (f) MS Pintal hinges of size 75mmx12mm. 2 Nos per leaf, (g) Including two coats of synthetic enamel paint complete. (h) Stainless steel wire cloth, 0.25mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to 2mm &fixed with aluminium wire staples. (j) Glass pane 5 mm thick fixed with MS pin and oil putty. NOTE: During Fixing of window, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.cutting holes and good dismantled portion in PCC(1:2:4) type B1.

Supply and Fixing SS, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed 300 mm long complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing SS, barrel tower bolts heavy section and fixed 200 mm long complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing SS handles, cast type, 150mm long complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing solid PVC door frames of size 50mm X 47mm made out of 5mm plain color PVC sheet reinforced with MS square tube complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing SS butt Hinges 100 mm (ISI) marked welded with MS Chowkhat complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Butt hinges, medium weight, cold rolled mild steel 100 mm (ISI Marked), fixed with steel chromium plated bright screws complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Aluminium alloy handles, fabricated type, anodised 150mm size complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Aluminium anodised, barrel tower bolts of extruded section 200mm long complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed by the Engineer-in-charge.

S&F anodised aluminium Window and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (01 No), hinges type B-21 100mm long (02 Nos) suitable handle (01 No) complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 5.0mm thick Figured glass, pin head type and glazing with clips n exc 0.5 sqm in each pane complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm as in doors complete all as specified and directed by the Engineer-in-charge.

Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc, including cleaning complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 110mm bore PVC(SWR) Rainwater pipes single socketed, in any length with rubber ring joints fixed to wall/in vertical position complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing PVC(SWR) bends any radius for 110mm bore pipe complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair Stack clamps made out of 50mm by 5mm Flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof suitable for 110mm dia pipe including drilling holes and fixed complete all as specified and directed by Engr-in-Charge

Material and Labour for connecting rainwater pipes at water oulets at roof slabs by necessary cutting and completely sealing around the rain water pipe in cement mortar 1:1 and finally applying a water proofing treatment around the pipes to stop water leakage/seepage from the mouths of rain water pipes complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair for ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, screwed for iron pipe 20mm bore (min weight 210 gms), as in repair complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair fancy type Bib tap with flange cast copper alloy CP 15mm bore dia. screwed for iron pipe or for brass ferrule and complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs 15mm dia fancy type CP stop cock, cast copper alloy screwed down high pressure, screwed both ends for iron pipe or for union complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair Angle cock with flange 15mm bore, chromium plated cast copper alloy with crutch or butter fly handle high pressure screwed down complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair cast copper alloy chromium plated Pillar cock 15mm dia screwed down high pressure with or without lettered (Hot or Cold) with long screwed shank and fly nuts screwed for iron pipecomplete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair waste coupling PTMT (half or full threaded) (minimum weight 32mm-45 gms), 32mm bore discharge pipe complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair waste coupling PTMT (half or full threaded) (minimum weight 32mm-45 gms), 40mm bore discharge pipe complete all as specified and directed by the Engineer-in-charge.

Supply and fixing in repairs 32 mm dia bore PVC waste pipe 800mm long suitable for Wash Hand Basin/Kitchen Sink complete all as specified and directed by the Engineer-in-charge.

Supply and fixing in repairs 15mm dia PVC connection with PTMT check nuts of length 450mm complete all as specified and directed by Engr-in-Charge.

Supply and Fixing in repairs Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs brass chromium plated towel rail 20 mm outer dia `D’ type, 60 cm long between flanges with and including chromium plated brass screws and wooden / plastic cleats,complete all as specified and directed by the Engineer-in-charge.

Material and Labour for repair to PVC Flushing cistern of 10Ltr capacity by adjusting float assembly, replacing flush handle and making functional complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair 125mm Overhead Shower ABS round with 225mm stainless steel Arm & Flange ,fixing to steel pipe or union complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair Plastic water closet seat cover,white, closed pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair Plastic water tank cover,for existing water tanks complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair 15mm Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair 15mm bore but fancy type, chromium plated with long shank and cup (concealed type) complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair Brass CP Wall mixer 3 in 1 (provision for over head shower & hand shower) mixing hot and cold water, including fixing to steel pipe or union 15mm bore dia pipe complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair Brass CP sink mixer with regular spout mixing hot & cold water, including fixing to steel pipe or union 15mm bore dia pipe complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair Brass CP centre hole basin mixer without popup base system complete all as specified and directed by the Engineer-in-charge.

Supply and fixing 15 mm tubes medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floor including taking up or down GI tubing complete all as specified and directed by the Engineer-in-charge.

Supply and fixing 20 mm tubes medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floor including taking up or down GI tubing complete all as specified and directed by the Engineer-in-charge.

Material and Labour for cutting chases for concealed water tubing and making good to facing in cement mortar 1:3, cutting not exceeding 10cm girth complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs PVC valve less syphon action type low level flushing cistern 8-10 liters capacity with intel, ball valve, float valve push button type handle including telescopic flush pipe 32 mm diacomplete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs vitreous chinaware wash hand basin white, flat back of size 550x400 mm excluding tap but including brackets fixing to wall and two Nos 10mm dia 100mm long nut and bolt over brackets including 32mm bore PVC waste pipe and CP waste coupling complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs vitreous china squatting pan 'Orissa pattern size 580x440mm white with 'P' or 'S' trap and integral foot rest (excluding, flushing cistern and flush pipe) squatting pan including connection 'P' trap and to flushing pipe, anti syphonage pipe and trap set in and including concrete and making good the flooring as per existing specification and taking out existing WC complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs vitreous china wash down water closet pan (pedestal pattern) white, with 'P' or 'S' trap (excluding flushing cistern and flush pipe) including connection to drain and to flushing pipe complete incl making good to floor to match with adjoining surface and taking out existing WC complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair Cabinet mirror plastic body for toilet of size 350x450mm with 4mm thick looking mirror complete all as specified and directed by the Engineer-in-charge.

Supply and fixing in repairs 500 Litre capacity Rotational moulded white colour polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position including GI tank nipple etc. complete and all as specified and as directed by Engineer-in-Charge. including dismantling existing water tank and removing from site of any capacity.

Supply and Fixing in repair 20 mm dia Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm as in doors and windows with necessary nuts and bolts/ fillets complete all as specified and directed by the Engineer-in-charge.

Taking down and Refixing in same opening shutters of any description exc 1sq.m and n exc 2 sqm each complete all as specified and as directed. Note : The rate includes for taking down, easing and adjusting and also fixing new builders hardwares as required including replacement of unserviceable screws etc. complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Sheet glass 3mm thick ordinary quality and glazing with oil putty including Hacking out old glasses from steel window / ventilator in any position and any description including punching or drilling out old glazing pins / springs clips and providing and fixing new one complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Figured glass, Pin head type 3mm thick and glazing with oil putty including Hacking out old glasses from steel window / ventilator in any position and any description including punching or drilling out old glazing pins / springs clips and providing and fixing new one complete all as specified and directed by the Engineer-in-charge.

Material and Labour for repair to Aluminium door/windows of any size/any description, including taking down from existing opening and refixing in the same position after tightening, easing the section as required for smooth movement/operation of door/window shutter, including fitting the rubber packing, aluminium snap beading, re-setting floor/hydraulic spring complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs Door closer hydraulically regulated, aluminium (extruded section body), designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed by the Engineer-in-charge.

M&L for rendering 15mm thick on the other than fair face of brick or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement including taking down cement plaster on brick or stone wall etc incl racking out joints, hacking for keys and preparation of newly plastered wall or concrete surfaces and applying two coats of oil bound distemeper over two coats of wall putty over a coat of primer complete all as specified and directed by the Engineer-in-charge.

Material and Labour for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surface and finished even and smooth without using extra cement including taking down cement plaster on brick or stone wall etc incl racking out joints, hacking for keys and preparation of newly platered or unplastered surfaces of wall and applying Two coats of exterior emulsion paint (weather coat) over a coat of primer in any shade or colour as approvedcomplete all as specified and directed by the Engineer-in-charge.

Material and Labour for 5mm thick cement plaster on ceiling surface in cement mortar 1:3 finished even and smooth without using extra cement including taking down cement plaster on brick or concrete surfaces etc incl racking out joints, hacking for keys and three coats of white wash on newley plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed by the Engineer-in-charge.

Material and Labour for preparation of old plastered or unplastered surfaces of walls and applying two coats of white wash complete all as specified and directed by the Engineer-in-charge.

Material and Labour for preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed by the Engineer-in-charge.

Material and Labour for complete removal of existing treatment from walls complete and applying two coats of oil bound distemeper over two coats of wall putty over a coat of primer complete all as specified and directed by the Engineer-in-charge.

Material and Labour for preparation of old plastered or unplastered surfaces of wall and applying one coat of oil bound distemper complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Preparing old wooden surfaces and applying one coat of synthetic enamel paint complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Preparing old steel surfaces & applying one coat of synthetic enamel paint complete all as specified and directed by the Engineer-in-charge.

Material and Labour for applying one coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over old surfaces. any shade or colour as approved complete all as specified and directed by the Engineer-in-charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Non skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match laid over screed bed or bedding layer 15 mm thick in cement mortar 1:4 including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubish of the premises complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Non skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match laid over screed bed or bedding layer 15 mm thick in cement mortar 1:4 including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubish of the premises complete all as specified and directed by the Engineer-in-charge.

Material and Labour for coloured glazed ceramic tiles in vertical surface 450 x 300 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the shade of tiles including 10 mm thick screed bed or bedding layers in cement mortar 1:3 for laying tiles on vertical surfaces, including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubish of the premises complete all as specified and directed by the Engineer-in-charge. (Note : Rate includes for carefully taking down fittings/fixtures such as WHB, Flushing cistern, towel rod, GI pipes etc and refixing the same after tiling work complete.)

Material and Labour for Cement concrete type D- 2,1:4:8 (40mm graded aggregate) as sub base for hard standing complete all as specified and directed by the Engineer-in-charge.

Material and Labour for outdoor (Endura) tiles30cm x 30cm x 12-15 mm thick, set, jointed and pointed in neat cement slurry in floors including 15 mm thick bedding layer in CM 1:4 complete all as specified and directed by the Engineer-in-charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed by the Engineer-in-charge.

Providing pre cast cement concrete in landing cover slab for manholes 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) finished even smooth complete all as specified and directed by the Engineer-in-charge.

TMT Mild steel bars upto 10mm dia, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm diacomplete all as specified and directed by the Engineer-in-charge.

Demolition of cement concrete (unreinforced) as in padding layers of Roofs, floors (other than ground floors) and similar suspended work including removing old APP membrane or similar like complete all as specified and directed by the Engineer-in-charge.

Material and Labour for 40 mm thick cement concrete type B0 1:2:4 (12.5mm graded aggregate) as in padding on existing roof surfaces & roof kerbs, rounded or chamfered on edges complete all as specified and directed by the Engineer-in-charge.

Material and Labour for rendering 10mm thick with CM (1:4) on concrete surface including WPC, roof finished even and smooth without using extra cementcomplete all as specified and directed by the Engineer-in-charge.(WPC measured and paid seperately)

Supply only integral liquid water proofing compound complete all as specified and directed by the Engineer-in-charge.

Supplying and applying fibre reinforced, UV resistant elastomeric liquid applied waterproofing & Heat reflective coating coating with PU Hybrid polymers & acrylic fibres, SmartCare DampProof Ultra or approved equivalent. The coating shall resist 10 bars of water pressure as per DIN 1048 standards, with elongation of 350% as per ASTM D412 & crack bridging of upto 2.5mm conforming to ASNZ standard, The coating shall reduce the surface temperature of 10 degrees,etc complete all as specified and directed by the Engineer-in-charge.

Cleaning of blocked WC seat any type/pattern (pedestal/squatt Orissa pattern) up to 1st manhole and making the drain pipe of any size full functional by flushing with water to entire satisfaction of Engineer-in-Charge including cleaning of 1st manhole and removing the waste material/sludge etc to a distance n.exc 300m and burying the same in pits and top surface covered with earth complete all as specified and directed by the Engineer-in-charge.

Cleaning /clearing & Maintenance of sewage lines, manholes including CI stacks, incl under ground sewage lines any depth by removing any type of blockage from sewage drain upto and including 300mm dia by rodding or any other means from manholes to manholes or from trap and flushing with water after cleaning including manholes. Sludge/sludge water to be disposed off through sludge in form of semi solid/loose state will be disposed off by burring with in any distance outside the periphery of defence land including taking off manhole covers and refixing the same after cleaning. The operation shall be executed/carried out as under. NOTE:- 1. The contractor shall keep the sewage line functionally throughout the contract period. Any kind of sewage cleaning device such as sewage cleaning Mechanical Pump / Vehicle including in the rate quoted by the contractor complete all as specified and directed by the Engineer-in-charge.

Material and Labour for single component polymer modified repair mortar with compressive strength minimum 38 MPA at 28 days (ASTM C 109:99) and tensile strength minimum 2.5 Mpa (ASTM C 307) in a single coat @ including Applying epoxy bonding agent and making good with polymer modified plaster and micro concrete as required thickness over a coat of rust removing alkaline primer and match the finishing to the existing surface. Modified plaster 10mm to 20mm thick as per manufacturer instructions complete Make : Fosroc, Sikka or equivalent and finishing the surface by applying two coats exterior emulsion paint (weather coat) any shade or colour as approved over a coat of primercomplete all as specified and directed by the Engineer-in-charge. Note : The rate includes for chiselling of loose reinforced cement concrete from RCC structures like RCC Walls, Columns, beams, parapets, chajjas, landing slabs etc and necessary formwork and scaffolding to carry out work upto double storey bldgs.

Supply and Fixing heavy duty movable castor wheel of load bearing capacity 50 kg to 100 Kg set plate +brake type and fixed in kitchen cabinets under the shelves complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Factory made single extruded WPC (Wood PolymerComposite) UV coated solid plain flush door shutter of 18 to 20 mm size comprising of virgin polymer of K value 58-60.(Suspension Grade), calcium carbonate and naturalfibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screwwithdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm², modulus ofelasticity 850 N/mm² and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunkS.S screws, in kitchen cupboards and room wardrobes shutter complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed by engr in Charge.

Supply and Fixing stainless steel slip on soft closing concealed hinges for cabinet doors 110 mmX 60mmX30mm complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 100 mm long SS handles for Cabinates complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 40 mm wide Continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe with s or P trap of 100 mm bore complete all as specified and directed by engr in charge

Material and Labour for Cement concrete type E-2 1:5:10 using 40 mm graded aggerigate in foundations, filling and mass concrete

Material and Labour for 30 mm thick PCC type B-0, 1:2:4 (12.5mm graded aggregate) on the base of sunken portion

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation etc and n exc 1.5m in depth and getting out in soft.loose soil complete all as specified and directed by the Engineer-in-charge.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed by the Engineer-in-charge.

Material and Labour for reinforced concrete pipes class NP2 150mm dia, laid and jointed complete all as specified and directed by the Engineer-in-charge.

Material and Labour for cement concrete 1:3:6 type C-2 for bed to drain pipes 150 mm dia including packing under, and haunching against the sides of pipes complete all as specified and directed by the Engineer-in-charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed by the Engineer-in-charge.

Removing excavated material nexc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed by the Engineer-in-charge.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. of size Exc 250 Ltr and upto 500 Ltr complete all as specified and directed by the Engineer-in-charge.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Brick work with sub class 'B' brick old size straight or curved on plan built in cement mortar 1:6 complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Brick work with sub class 'B' brick straight or curved on plan built in cement mortar 1:6 (Except Brick) complete all as specified and directed by the Engineer-in-charge.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed by the Engineer-in-charge.

M&L Structural steel, rolled section such as joist, beam, channel, angle, tee, of Fe 410-W (Gde-E-250) quality- A in available lengthscomplete all as specified and directed by the Engineer-in-charge.

Supply only Chain link MS galvanisd fencing, any size or type for fencing. complete all as specified and directed by the Engineer-in-charge.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed by the Engineer-in-charge.

Dismantling expanded metal, any thickness or mesh, fixed with steel or wood fillets, if any not exc 5 kg/Sqm complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Mild steel screw bolts 5 to 10 mm dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5 cm long complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, complete all as specified and directed by the Engineer-in-charge.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick complete all as specified and directed by the Engineer-in-charge.

Material and Labour for PCC type C-2, 1:3:6 (40 mm graded aggregate) in foundation filling and mass concrete arrangements complete all as specified and directed by the Engineer-in-charge.

pardeep singh marwaha (BID ID -3106964)

Surya & Gautam Builders (BID ID -3111292)

DABGOTRA BUILDERS (BID ID -3123743)

Auto India (BID ID -3123152)

dadwal engineers (BID ID -3110858)

M/S HARBANS SINGH BEDI (BID ID -3124086)