ADDITION/ALTERATION AND SPECIAL REPAIRS TO BLDG NO P 21 NEAR PM BLDG MCM DEPT AT NAVAL DOCKYARD MUMBAI ADDITION ALTERATION ROOF SHEET AT CN 92 CONSERVANCY DEPT AT ND MUMBAI ADDITION ALTERATION AND SPECIAL REPAIR TO C NO 58 59 BLDG 45A 63A WEAPON DEP

Amount

Demolition of cement concrete un reinforced in ground floors and paving n exc 15cm thickness below or above GL complete all as specified and as directed

Supply and Fixing 15mm bore GI tubes, medium grade, to walls and ceiling or laying in floors including all necessary medium grade ISI marked GI fitting complete all as specified and as directed

Supply and fixing 20mm dia tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete incl holes in walls and floors shall be made by drilling with drill or jumper and not by dismantling the brick/concrete after fixing, holes shall be made good with CM 1:3 properly complete all as specified and as directed

Material and labour for 25mm thick cement concrete type B-1, 1:2:4 (20mm graded aggregat) as in floor complete all as specified and as directed

Supply and fixing Aluminium snap grid size of 600mmX600mmframe work of 24X38X0.6mm. Tee section (bottom pre-coated) and 24X24X5mm thick angle alongwith the wall incl suspenders as per manufacturer instuction as in ceiling and Supply and fixing of absestos free calcium Silicate designer boards 4mm thick complete all as specified and as directed

Material and labour Non skid ceramic coloured tiles 8 to 10 mm thick (Square/rectrangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38sqm, in floors etc over and including 15 mm thick cement screed bed in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed

All as per item No. 06 above, but as on vertical surface such as skirting, dados and risers over and including 10mm thick backing coat in CM 1:4 complete all as specified and as directed

Material and labour for rendering 15 mm thick on brick/stone masonry surface or surface other than fair face of brick-work in CM 1:6 and finished even and smooth with out using extra cement complete all as specified and as directed

Material and labour for rendering 15mm thick on fair faces of stone/brick wall surface with water proofing compound @ 2% by weight of cement and finished surface even and smooth with out using extra cement in CM 1 :6 complete all as specified and as directed: (Note wpc compound shall be measured and paid seperately)

Supply and fixing Solid PVC door frame of size 50mmX47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet (edges will be painted to match with prelam sheet) reinforced with MS square tube, suppling & fixing in opening as per specification complete all as specified and as directed

Supply and fixing factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6mm raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site complete all as specified and as directed

Supply and fixing 100mm size butt hinges extruded aluminium alloy with galvanized mild steel hinge pin anodised and fixed type c-21 etc complete all as specified and directed by Engr-in-charge.

Supply and fixing 2nd class H/W small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, incl all necessary labours, articles n exc 200 cu.cm each complete all as specified and as directed

Supply and fixing in repair 15mm bore brass bib taps cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed (weight not less than 400gms) complete all as specified and as directed

Supply and fixing 15mm bore stop cock (Concealed type) CP fancy type with, screwed down, high pressure for iron pipes or for unions fixed in repairs (weight not less than 400gms) complete all as specified and as directed

Supply and fixing CP pillar tap cast copper alloy chromium plated fancy type high pressure with or without lettered hot or cold with long screwed shank and fly nut screwed for iron pipe 15mm dia fancy type (weight not less than 400gms) complete all as specified and as directed

Supply and fixing in repairs white vitreous china washed down water closet pan, (pedestal pattern), white, with and including P/S trap, PVC solid type seat cover etc complete all as specified and as directed

Supply and fixing vitreous china wash basin, oval shape, white, size 550 X 400mm incl brackets or bedding in cement mortar to wall complete all as specified and as directed

Material and labour 32mm dia waste coupling, PTMT for glazed ware sinks, basin, etc with long shanks and fly, flange end complete all as specified and as directed

Supply and fixing PVC connection on pipe 450mm long with brass nut bolt complete all as specified and as directed

Supply and fixing PVC waste pipe 32mm dia 800mm long with socket suitable for WHB/Sink complete all as specified and as directed

Supply and fixing PVC (SWR) Pipe single socketed in any length with rubbering joints laid in trenches or in floor/ walls for 110mm dia complete all as specified and as directed

Ditto - all as per item No 22 above but 75mm dia

Supply and fix PVC Bends any radius 110mm dia provided with access door complete all as specified and as directed

Ditto - all as per item No 24 above but 75mm dia

Supply and fix PVC (SWR) Junction single T equal or unequal 110mm dia provided with access door complete all as specified and as directed

Ditto - all as per item No 26 above but 75mm dia

Material and labour 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate incl finished even and smooth with using extra cement as in plinth protection incl necessary form work to edges complete all as specified and as directed

Use and waste of formwork to soffits of suspended slabs, landings, shelves and similar work n exc 200mm thick horizontal or sloping complete all as specified and as directed

Supply and fixing 1st class hardwood moulding as in cornices, joints of wall wall panelling boards etc sectional area not exc 6 Sq cm including necessary french polish complete all as specified and as directed

Supply and fixing for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed

Supply and fixing for 1st class hard wood of any size (e.g Teak Wood Seasoned) plain, solid, for beam, column and truss members, straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue complete all as specified and as directed

Material and labour Two coats of synthetic enamal paint over a coat of pink primer on newly wood/wood based surfaces over 10cm width or girth incl preparation of new surface complete all as specified and as directed

Material and labour One coat of synthetic enamal paint on old painted wood/wood based surfaces over 10cm width or girth incl preparation of old painted surface complete all as specified and as directed

Material and labour One coat of synthetic enamal paint on old painted steel surfaces over 10cm width or girth incl preparation of old surfaces complete all as specified and as directed

Material and labour for preparation of newly plastered wall surfaces, over 10cm girth, applying two coats of 100% acrylic, weather resistant emlusion over a coat of exterior wall primer complete all as specified and as per manufacturer's instruction complete all as specified and as directed

Material and labour complete removal of existing plastered wall surfaces, over 10cm girth, preparation of surfaces, applying two coats of 100% acrylic, weather resistant emlusion over a coat of exterior wall primer complete all as specified and as per manufacturer's instruction complete all as specified and as directed

Material and labour for two coat of oil bound distemper over 1mm thick of birla white putty including preparation of newly surface etc complete all as specified and as directed

M& L for complete removal of existing treatment and applying one coat of Oil bound distemper over 1mm thick birla white putty including preparation of surface complete all as specified and as directed

Supply and fixing mild steel framed work such as in frames gates, grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, framed balusters, walk ways, railings, framework of water tank and similar work con-forming to Fe-290. Gde E-165 complete all as specified and as directed

Material and labour for Cleaning of surface of floor by brooming, washing and drying with cloth including removal of oil mats and provision of high density laminated wooden flooring (pergo) 8mm thick fixed in floors / skirting including moulding etc, including dismantling old unserviceable wooden flooring complete all as per manufacturer's instructioncomplete all as specified and as directed. make:" Pergo / ROSETTA" complete all as specified and as directed

Material & labour for water proofing plaster for sunken portion in CM 1:3, 15 mm thick in two coats with integral water proofing compound at the rate of 3 % by weight of cement and finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge

Material and labour for water proofing treatment of sunken floor / wall surfaces by applying two coats of elastomeric coatings of BRUSHBOND RSX in FOSROC or TECKFORCE 2K STRONG in CHOWKSEY CHEMICALS as a two component flexible elastomeric coating with minimum 2mm thickness layer complete as per manufacturer’s instruction’s complete all as specified and as directed

Material and labour clean plastered surface and remove all loose particles, dirt, vegetation etc. Define the crack with sharp edge tool then clean and moisten. Providing and applying ready to use acrylic polymeric non - shrink "PAINTEX-4" upto 5mm 12mm wide cracks and finish at all heights, level etc. complete after 24 hours inspect and if requuired as a result of auto-suction, provide another filling over the same complete all as specified and as directed

Errection & dismantling of MS tubular double scaffolding (H frames) upto ht of 30 m & with necessary bracing, provision of necessary safety equipment to the skilled workers to carry out the work and covering with green cloth for carring out external facework of walls complete all as specified and as directed.

Material & labour for cleaning the existing cracked surface of wall & Column surface by scrubbing so as to remove all the dust, dirt, grime, oil etc and washing the surface with Jet of water and applying one coat of FUTURA SEALER COAT in CHOWKSEY CHEMICALS (or equivalent in FOSROC, ASIAN, BERGER etc) @ 8-10 SQM , then after 4-5 hours apply two layer of finish coats of FUTURA-5 PLUS in CHOWKSEY CHEMICALS (or equivalent in FOSROC, ASIAN, BERGER etc) @ 4-4.5 SQM/2 coat duly included erection and dismantling of scaffolding upto 9 storey building, complete all as specified and directed. Note: Rate should be included with filling the cracks with acrylic polymeric non shrink compound like Paintex-4 in CHOWKSEY CHEMICALS or equivalent in other approved makes.

Material and labour for taking down , chipping and removing the loose, spailt, damaged cement concrete, cement mortor surfaces of RCC Columns, beams, walls, chajjah etc and exposing the reinforced cement , wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthen the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing polymer modified cement and quartz sand mortor in CM (1:3) mix, 40mm thk in two coats, using polymer @ 10 to15% by weight of cement complete all as specified and directed. Note :-(New reinforcement and MS Sections will be measured and paid separately) Make : Dr. Fixit/Sunanda/chemestik/Fosrok

Removing excavated materials (soil) exc 250 m but n.exc 500m and depositing where directed including spreading and levelling complete all as specified and as directed

Taking down cement plaster on brick / surfaces built in cement mortar including raking out joints, bedding for key scrubbing down with water etc complete all as specified and as directed

Dismantling floor hearth or wall tiling including cement mortat bedding but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed

Taking down chowkats or frame with shutter ( without taking off shutter from frame) , n exc 1.5 sqm each complete all as specified and as directed

Taking down chowkats or frame with shutter ( without taking off shutter from frame) exc 1.5 sqm but n exc 4 Sqm each complete all as specified and as directed

Demolition of Unreinforced cement concrete of any description and in any position not other wise specifically provided for complete all as specified and as directed

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed

Material and labour for cement concrete type B1 1:2:4 (20 mm graded aggregates), in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed

Demolition of brick work or stone /boulder masonry built in cement mortar, including all quoins, arches, pillars, etc complete all as specified and as directed

Material and labour for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in setting in CM (1:6) complete all as specified and as directed

Material and labour for brick work with sub class 'B' bricks (old Size) straight or curved on plan to any radius but half brick thick wall built in CM 1:4 complete all as specified and as directed

Supply and fixing Powder coated aluminium frame for doors, windows, ventilators and partitions with one or more rebates including joining cleat for fixing etc complete all as specified and as directed

Supply and fixing 4mm thick backelite with decorative choice laminated on both side complition complete all as specified and as directed

Material and labour Sheet glass 4 mm thick, ordinary quality and glazing in aluminium beading with screws/ rebates in square n.exc 0.5 sqm in each pane complete all as specified and as directed

Material and labour Sheet glass 4 mm thick, ordinary quality and glazing in aluminium beading with screws/ rebates in square exc 0.5 sq.m in each pane complete all as specified and as directed

Supply and fixing 100 mm stainless steel Butt hinges complete all as specified and as directed

Supply and fixing Aluminium anodised sliding door bolt 300m long, with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed .

Supply and fixing aluminium anodised Barrel tower bolts of extruded section, length of bolt 200mm complete all as specified and as directed

Supply and fixing Extruded aluminium anodised alloy handles, fabricated type 150mm size complete all as specified and as directed

Material and labour for Floor door stopper of aluminium alloy body 150 mm long and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed

Material and labour for Non skid coloured ceramic tiles 7 to 8 mm thick ( square/ rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of the tiles with and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed

Material and labour for Coloured glazed ceramic tiles in vertical surface 450X350X7mm thick with and including 10 mm thick cm (1:4) backing coat and Triangular filleting at top of skirting, set and jointed in neat cement paste and pointed in coloured cement to match the shade of the tiles complete all as specified and as directed

Material and labour double charge premium quality vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles exceeding or equal 0.36 Sqm but n.exc 0.42 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match in floor including 20mm thick screed bed or bedding layer for laying floor finishes in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Material and labour double charge premium quality vitrified ceramic tiles 10mm thick polished area of each tiles not exceeding 0.64 Sqm, as in skirting /vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

Material and labour stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed

Taking down PVC wastage and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and directed.

Supply and fixing 110 mm dia PVC ( SWR) grade double T/Y with access doors including fixing clips complete all as specified and as directed

All as per item No 74 above but 75mm dia complete all as specified and as directed

Material and labour for hard wear stone (of any type) granite stone slab 20 mm thick in flooring machine cut, in plateformbedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed

Material and labour for rendering 20mm (15 mm thick backing coat + 5mmthick finishing coat) thick on fair faces of brick work or concrete Surface in CM 1:4 and finished even and smooth with out using extra cement. complete all as specified and directed by EIC (Note : WPC will be measured and paid seperated).

Material and labour for complete removal of existing treatment on wall surfaces and applying a coat wall care putty 3mm thick on plastered surfaces, preparatory to distempering and applying two coats of oil bound distemper over a coat of wall primer complete all as specified and as directed.

Material and labour for preparation of new plastered wall surfaces and applying a coat wall care putty 3mm thick on plastered surfaces, preparatory to distempering and applying two coats of oil bound distemper over a coat of wall primer complete all as specified and as directed.

Material and labour 3 mm thick sheet float glass ordinary quality and glazing with oil putty or beads in square n exc 0.5 sqm in each pane windows/doors etc complete all as specified and as directed

Material and labour 4 mm thick plain glass sheets ordinary quality in squares nexc 0.5sqm each pane fixed with rubber beading for aluminium windows/doors etc complete all as specified and as directed

Material and labour 4 mm thick plain glass sheets ordinary quality in squares exc 0.5sqm each pane fixed with rubber beading for aluminium windows/doors etc complete all as specified and as directed

Material and labour for anodised Aluminium grid frame work for false ceiling of grid size 605x605 mm with hanger 6 mm dia GI (upto 1200mm length) adjusted level fixed to roof slabs by means of ceiling cleas made out of GI flat 40x3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long with calcium silicate board of siliceious and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm (etc complete all as specified all as specified. (make: Everest or equivalent as approved by GE)

Dismantling plain or corrugated steel sheeting, any gauge or thickness incl Nainital or similar pattern roof coverings all as specified and directed.

Supply and fixing pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, chajjas, valley gutter, ridge and fixed with crumple joint etc fixed with self tapping screws all complete all as specified and as directed

Material and labour for 12 mm thick Medium density fibre board, exterior grade, fixed to timber/ Aluminium Frame work with .screws complete all as specified and as directed

Supply and fixing in repairs Roller venetian blinds type made out of standard cloth of approved texture with necessary accessories etc complete all as specified and as directed

Dismantling of wrought iron or mild steel work of any despcription not other wise provided for complete all as specified and as directed

Material and labour for mild steel roof truss (framed), trussed, purlins, crane gantries, rails and fasternings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance piece, cleats etc complete all as specified and directed by EIC.

Supply and fixing Plain, galvanised, mild steel sheeting, 1 mm thick in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating complete all as specified and as directed

Material and labour for Cement concrete type D2 1:4:8 (40 mm graded aggregate) in surface channels and drains complete all as specified and as directed.

Material and labour Cement concrete type D2 1:4:8 (40 mm graded aggregate)in foundations, filling and mass concrete complete all as specified and as directed.

Dismantling of Stone slabs laid bedded and pointed and tiles of any description or thickness in floors, aprons etc complete all as specified and as directed.

Material and labour for Dismantling of machine pressed precast concrete inter locking paver block any size of refixed/ laid over and including 25 mm thick fine sand cushion to a line and slope etc and joined complete including spreading screened river sand over surface for filling the joints with rising surface vibrator complete all as specified and as directed.

Material and labour for machine pressed precast concrete inter locking paver block any shape and size confirming to IS-15658-2006 of 80mm thickness M-40 Grade, glossy finished of approved colour laid over and including 25 mm thick fine sand cushion to a line and slope etc and joined complete including spreading screened river sand over surface for filling the joints with rising surface vibrator complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard dense soil complete all as specified and as directed.

Material and labour for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Ditto all as per item No 97 above but 6mm to 8mm dia.

Supply and fixing mild steel Framed work as in doors or gates (Fe-290 Gde E-165) of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed

Supply and fixing mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed

Supply and fixing in repairs stainless steel railing complete all as specified and as directed

Material and labour 75 mm thick PCC 1:4:8 type D2 Using 40mm graded stone aggregate as subbase/ sub floor allas specified complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard and dense soil complete all as specified and as directed.

Material and labour for reinforced cement concrete type B2 (1:2:4) 40mm graded aggregate in foundations, filling and mass concrete complete all as specified and as directed.

Supply and fixing for mild steel plates of gradeFe410-W, (Gde-E-250) quality-A as in connecting plates, base plate etc complete all as specified and as directed

Material and labour for preparation of new steel Surfaces of any description, over 10cm in width orgirth,applying two coat of synthetic enamel paints over a coat of red oxide primer complete all as specified and as directed

Material and labour 100 mm thick PCC 1:4:8 type D2 Using 40mm graded stone aggregate as subbase/ sub floor allas specified complete all as specified and as directed.

Material and labour for providing 100mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in floor and surface shall be finished with broom including necessary form work required complete all as specified and as directed

Material and labour for rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surface finished even and smooth without using extra cement rough finished complete all as specified and directed.

Material and labour for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed.

Supply and fixing 0.8mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275mm complete all as specified and as directed

Material and labour for roof treatment by application of two coats elastomeric coating of "Tech O THANE PU-White" @ 1.5Kg/SQM in CHOWKSEY CHEMICALS or NITOPROFF 600 PF @1.5KG/SQM in FOSROC or equivalent in IWL etc with DFT of minimum 1mm thickness on primed surface by using special gradeof Primer PR 71 in CHOWKSEY CHEMICALS or NITOPROFF Primer in FOSROC complete all as specified and as directed

Material and labour 10mm thick polymer modified mortar in cement mortar (1:3) with graded quartz sand with additive monolith - PMM of krishnaconchem or polymer mortar HB of Dr, Fixit or Shalifix RM SG 01STP ltd. 15% by weight of cement in one coat with and including curing as per manufacturing instruction complete all as specified and as directed

Material and labour for taking down , chipping and removing the loose, spailt damage cement concrete, cement mortar surface of RCC columns, beams,walls,chajjah etc and exposing the reinforcement , wire brushing and cleaning the exposed steel reinforced bar, applyingrust remover over the cleaned rebar surface wash the rebar with clean water for removing all rusts from the old re bar surfaces, fixing new reinforcement for strengthening the members as required, applying two coat of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surface and finally providing ready mix polymer plaster and finally finishing the surface all as specified and directed. Make: Dr. fixit/Sunanda/Chemestik/Fosrok as aproved Note;- New reinforcement and MS section will be measured and paid separately.

Use ans waste Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and as directed

Material and labour RCC 1:2:4 type B1 using 20mm graded stone aggregate as in Slabs supported on walls,beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified by Engg-in-charge.

Supply and fixing for roof tiles Manglore pattern interlocking at side joint laid dry all as specified and directed by Engg-in-charge.

Supply and fixing for ridges of hip tiles to suit manglore pattern or roofing tiles, bedded and jointed in lime mortar 1:3 or cemnet mortar 1:6 complete all as specified and as directed

Supply and fixing false ceiling with powder coated exposed GI grid Suspension system grid of 600x600mm. Grid of Modular size 600x 600mm shall be supported by 4mm dia GI wire from purlil/soffit with including 4mm thick high pressur steam cured non asbestos fiber cement design ceiling boad (Densit>1200kg per Cum ) of size 595x595mm complete all as specified and as directed

Dismantling asbestos cement and any type of corrugated semi-corrugated etc sheets in roof coverings complete all as specified and as directed

Supply and fixing Rolled sections of Grade Fe 410-W (Gde E-250) quality A as in post, runners, rafters, purlins, trusses, steps etc fixed with connecting plates including bending welding etc complete all as specified and directed.

Material and labour for mild steel work in tubular trusses 50mm dia and posts incl including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

Supply and fixing 15mm bore dia pipe , brass chromium plated fancy type bib tap fixed in repairs complete all as specified and as directed

Supply and fixing in repairs 15mm size stop valves, fancy type chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends and fixed complete all as specified and as directed.

Taking down 15mm bore, GI tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed.

All as per item No 125 above but 20 mm bore GI Pipe complete all as specified and as directed.

Dismantling 100/75 mm bore, cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches if required complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not other wise specifically provided for complete all as specified and as directed

Supply and fixing 100mm Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and as directed.

Supply and fixing for granite stone slab 20mm thick machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing of type and including 10mm thick backing coat in CM 1:3 complete all as specified.

Supply and fixing white vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests, P/S trap etc. Fixed in repair complete all as specified and as directed

Supply and fixing in repair for health faucet ( Jet) 1 m long PVC tube with wall hook chromium plated fitted to stopcock 15 mm bore complete all as directed.

Supply and fixing in repairs 10 litres capacity PVC low level flushing cistern of approved make including ball valve,syphon set, inlet and outlet pipe, brackets etc complete all as specified and as directed

Supply and fixing white glazed earthen ware vitreous Oval type china wash hand basin of size 600x700 mm with and including CI brackets, with granite including 32mm bore brass CP waste coupling Inlet/ outlet PVC flexible pipe etc complete all as specified and as directed

Supply and fixing chromium plated,Tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed in repair complete all as specified and as directed.

Material and labour PVC SWR Floor trap 75mm, plain with grating including setting and jointing with silvent cement complete all as specified and as directed.

Supply and fixing in repair vitreous china urinal, half stall type complete including providing and fixing plugs bedding urinal against wall in cement mortar in 1:2 securing urinals to plugswith and including 60 mm brass screws, pointing around urinal back in cement , flush pipes, inlet ,outlet etc complete all as specified Fixed in repairs complete all as specified and as directed.

Supply and fixing in repair vitreous china urinal, bowl type (back or corner wall type) complete including providing and fixing plugs bedding urinal against wall in cement mortar in 1:2 securing urinals to plugswith and including 60 mm brass screws, pointing around urinal back in cement , flush pipes, inlet ,outlet etc complete all as specified Fixed in repairs complete all as specified and as directed.

Supply and fixing 75mm dia CP shower rose swivel type with & incl 460mm long brass CP heavy duty, fixed in repairs complete all as specified and as directed.

Material and labour for viterous china urinal partition white of size 310x700mm urinal partition slabs, terminating about 40cm above floor, fixed in repairs complete all as specified and as directed

Material and labour for complete removal of existing treatment on wall surfaces and applying and sanding the surface till even and smooth finish and applying one coat of wall primer and finally applying two coats of oil bound distemper of approval tint complete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions , surface of concrete sqaure, rectangular, polygonal complete all as specified and as directed.

Material and labour for taking down , chipping and removing the loose, spailt damage cemnet concrete, cement mortar surface of RCC columns, beams,walls,chajjah etc and exposing the reinforcement , wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned rebar surface wash the rebar with clean water for removing all rusts from the old re bar surfaces, fixing new reinforcement for strengthening the members as required, applying two coat of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surface and finally providing polymer modified cement and quartz sand mortar mortar in CM (1:3) mix 40mm thk in two coats, using polymer @10-15% by weight of cement complete all as specified and as directed Make: Dr. fixit/Sunanda/Chemestik/Fosrok as aproved Note;- New reinforcement and MS section will be measured and paid separately.

Material and labour for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.80mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed.

Providing and executing Polyrethane injection system to leakage points and after cleaning the surface and remove any dust unsound or contaminated material plaster, oil.paint, grease,corrosion deposited or algae etc. fixing of packers for injection and seal all the cracks using nitomortar PE polyester resin base repair mortar , injection nitofill Ws60 Rapid setting water stopping foam in running water when the water is stopping the cracks are reinjecting with nitofill UR63 solvent free two part polyuretha neresin. once grouting operation is completed remove the packers and make good any holes or voids with nitomortar PE and allow to cure etc complete all as specified and as directed.

NITOFILL WS60

NITOFILL UR63

NITOMORTAR PE

Supply only integral water proofing compound of ISI marked complete all as specified and as directed

Taking down carefully old U/S point wiring copper/Aluminium (light/ fan /sockets/power) complete with switches, sockets, fan regulators, ceiling roses, lamp holders, brackets and making good to disturbed surface complete all as specified and as directed by Engineer-in-Charge

Disconnecting & taking down, strip opening, cleaning all parts and packing of ceiling fan of any make and size & greasing ball bearing with specified quailty grease and painting complete all as specified and as directed by Engineer-in-Charge

Material and labour for hanging ceiling fan in position & re-comissioning the same including making electric connection complete all as specified and as directed by Engineer-in-Charge

Fabrication and fixing of ceiling fan hooks and clamp with nuts, bolts and washers and complete works required at site for fixing of hooks complete all as specified and as directed by Engineer-in-Charge

Supply and fixing Ceiling fan 1200mm sweep, suitable for operation on 230/240 V. 50 Hz, having air delivery not less than 200 cum/min, 350 rpm supply single phase. A.C. supply complete including connecting up with 3 core flexible cord of size 23/0.0076mm from ceiling rose to fan complete all as specified and as directed by Engineer-in-Charge

Material and labour for point wiring with FRLS PVC insulated, un-sheathed, multi stranded copper conductor cable of 1.5sqmm size 1100volts, drawn through and including non metalic rigid PVC casing and caping not less than 25mm with all accessories fixed on wall/ceiling/truss including FRLS PVC insulated, unsheathed, multi stranded copper conductor cable 1.5sqmm size as earth continuty conductor connected common earth dolly including required numbers and size of PVC Modular box with cover plate fixed on wall for fixing the switches, switch sockets, regulator etc complete all as specified and as directed by Engineer-in-Charge for:-

Note: a) Colour coding shall be followed as given below:-

i) Phase-Red/Yellow Blue

ii) Neutral-Black

iii) Earth-Green

Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit

One light point controlled by one 5A switch

One Fan point controlled by one 5A switch

One 5A flush type switch socket point on same board

One 5A flush type switch socket point on independent board

One Bell point contolled by one 5A bell push switch

Material and labour for point wining complete with proper colour coding using PVC insulated unsheathed multi stranded copper conductor cable 4.0 sqmm size, 1100 volts ISI marked FRLS grade drawn through and including non metalic rigid, double lock ISI marked, not less than 25mm casing caping with all accessories such as tee, bends, elbow, reducers, junction box etc fixed on wall/ceiling/truss and one run of PVC insulated unsheathed multi stranded copper conductor cable of 4.0 sqmm size, 1100 volt. ISI marked FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module complete necessary electric connection for each workstation point comprising of 02 Nos 6A sockets and 01 No 15A socket on same board complete all as specified and as directed by Engineer-in-Charge Note: (a) Colour coding shall be followed as (i) Phase- Red/YellowBlue (ii) Neutral-Black (iii) Earth-green (b) Switch socket measured & paid separately

Material and labour for point wring complete with proper colour coding using PVC insulated unsheathed multi stranded copper conductor cable 2.5 sqmm size, 1100 volts ISI marked FRLS grade drawn through and including non metallic rigid, double lock, ISI marked, not less than 25mm casing capping with all accessories such as tee, bends, elbow, reducers, junction box etc fixed on wall/ceiling/truss and one run of PVC Insulated unsheathed, multi stranded copper conductor cable of 2.5sqmm size 1100 volts, ISI marked FRLS grade green colour as earth continuity conductor connected to common earth dolly with and including modular box with cover plate frame in any module complete for One 5 pin, 15A switch socket combination on the independent board complete all as specified and as directed by Engineer-in-Charge Note: (a) Color: coding shall be followed as Phase-(i)Red/Yellow/Bue (ii) Neutral-Black (iii) Earth-green (b) Switch socket measured & paid separately.

Supply and fixing ceiling rose surface bakelite 65 x 50mm. flush type 3 terminals complete all as specified and as directed by Engineer-in-Charge

Supply and fixing modular switch 1 way 6A,1 module complete all as specified and as directed by Engineer-in-Charge

Supply and fixing modular switch 1 way 16A,1 module complete all as specified and as directed by Engineer-in-Charge

Supply and fixing modular socket 6A-2/3 pin combined 2 modules complete all as specified and as directed by Engineer-in-Charge

Supply and fixing modular socket 6/16A 2/3 pin, combined 2 module complete all as specified and as directed by Engineer-in-Charge

Supply and fixing for modular fan step regulator, 120W-2 modular complete all as specified and as directed by Engineer-in-Charge

Supply and fixing bell AC 230V SP 50 Hz musical type complete all as specified and as directed by Engineer-in-Charge

Supply and fixing modular bell push flush type 6A, 1 module complete all as specified and as directed by Engineer-in-Charge

Supply and fixing in repair of lamp holder PVC/polycarbonate insulated body type complete all as specified and as directed by Engineer-in-Charge Make:- C&S cat No.- ACBHA006/Roma/ Legrand

Supply and fixing in repair new generation recessed mounted ultra slim panel LED 2X2 Luminaire 36 watt and CRCA powder coated body and high translucent diffuser provides high quality ecomonic energy saving lighting to modern offices suitable for 600x600 mm modular/ POP/ Gypsum ceiling complete all as specified and as directed by Engineer-in-Charge. Make:- CG/ wipro/ C&S Cat Ne: LTCRSLM36WATT2X2/Bajaj/ Havells/ Philips

Supply and fixing in repair wall/surface mounted Sirius series PDC aluminium housing with polycarbonate diffuser, SMD LED and heat sink integrated with housing 10W LED bulkhead fitting complete with an accessories internaly pre-wired and including fixing the fitting on wall/ceiling including connecting up with twin core copper conductor cable with suitable size complete all as specified and as directed by Engineer-in-Charge Make:- CG/ wipro/ C&S cat No.- LTB10WLED/ Bajaj Havells/ Philips

Supply and wing in repair wall/surface mounted 10W LED 2 feet batten fitting engineering plastic batten with white acrylic cover complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round/square block-02 Nos including connecting up with twin core copper conductor cable with suitable size complete all as specified and as directed by Engineer-in-Charge Make:- CG/wipro/ C&S cat No.- LTTB2F10WLEDW BATTEN/ Bajaj/ Havells/ Philips

Supply and fixing in repair wall/surface mounted 20W LED batten fitting engineering plastic batten with white acrylic cover complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round/square block-02 Nos including connecting up with an core copper conductor cable with suitable size complete all as specified and as directed by Engineer-in-Charge Make:- CG/ wipro/ C&S cat No.- LTTB4F20WLEDEW BATTEN/ Bajaj/ Havells/ Philips

Removing the existing window Air conditioner 1.5/2TR complete including all accessories and closing opening of wall with brick working cement mortor 1:4, plastering white washing/ distempering to match with surroundings and Shifting of window type Air conditioner including accessories, making suitable size opening in existing wall suitable fixing air conditioner, fixing of wooden frame made out of not less than 50x75mm hard wood runners painting, finishing in cement mortor in 1:4 white washing/distempering to match with surroundings at suitable location complete all as specified and as directed by Engineer-in-Charge

Removing the existing Split AC 1.5/2.0TR complete including all accessories including making good the surface to match with surrounding and Material and labour relocation & refixing the Split AC for the new position/location including additional accessories as required, testing & commissioning complete all as specified and as directed by Engineer-in-Charge

Supply and fixing copper tubings of appropriate dia for suction line & for liquid discharge line duly Insulated with suitable insulation material including making hole in wall for passing through pipe and making distrubed surface complete all as specified and as directed by Engineer-in-Charge

Supply and fixing for Rigid non-metallic PVC conduit 20mm dia incl connecting to AC condenced water drain pipe complete fixing accessories such as tees, bends elbows, reducers mouth tube ends fixing accessories such as GI saddles, full threded screws and (Narayan) nylon rawl plugs etc surfaced on walls/roofs complete all as specified and as directed by Engineer-in-Charge

Supply and fixing GI cable tray perforated type 2mm thick of size 250x50mm to be fixed on any wall (brick/srione) vertically horizontally including all accessories complete bending, shaping, drilling welding, cutting & all fixing arrangement complete all as specified and as directed by Engineer-in-Charge

Suppply & fixing pre fabricated GI clamp suitable for fixing/supporting 250x50mm size cable trays complete with buzzer bolts/hold fastener complete all as specified & directed NOTE: Contractor deemed to be include making good to the disturbed surfaces to match with the existing complete all as specified and as directed by Engineer-in-Charge

Supply and fixing in repairs of 0.71mm thick powder coated aluminum sheet cover, alloy 31000 H4 in ridges Hips valley gutter including suitable size of revits/nut bolts complete bending, shaping, drilling, cutting notching complete all as specified and as directed by Engineer-in-Charge

Supply and fixing in repair of double door type vertical type TPN DB 4 Way 240V with 200A busbar, with metallic double door type IP 43 IK 09 protection suitable for housing MCCB's complete all as specified and as directed by Engineer-in-Charge Note:- DBS shall be concealed in wall where ever possible including making good the surface to match with surrounding

Supply and fixing in repair of double door type vertical type TPN DB 6 Way 240V with 200A busbar, with metallic double door type IP 43 IK 09 protection suitable for housing MCCB's complete all as specified and as directed by Engineer-in-Charge Note: DBs shall be concealed in wall where ever possible including making good the surface to match with surrounding

Supply and fixing MCCB FP 125 Amps, 16KA, complete all as specified and as directed by Engineer-in-Charge

Supply and fixing MCCB FP 63 Amps. 16KA complete all as specified and as directed by Engineer-in-Charge

Supply and fixing MCB SP 6-32 Amps, 10KA ‘C’ series 240V complete all as specified and as directed by Engineer-in-Charge

Supply and fixing MCB TPN 63 Amps 10KA complete all as specified and as directed by Engineer-in-Charge

Supply and fixing repair of mini MCB SP 25 Amps 240V 3KA including 3 module box and cover plate complete all as specified and as directed by Engineer-in-Charge. Make:- Legrand/ Crabtree cat No.- DCVNCSPA025, Cover plate cat No-ACVPPCWV03 Box Cat No-ACTXMIX03/Anchor/Roma plus

Taking down old sub main & Material and labour Submain wiring with 4 Sqmm single core multi stranded PVC Insulated & unsheathed copper conductors 1100 volts FRLS grade.ISI make drawn through & including PVC non metallic casing and capping with Accessories fixed on wall/ceiling/truss etc including one PVC insulated & unsheathed multi stranded copper conductor 4.0 Sq. mm FRLS grade ISI make as earth continuity conductor connected to common earth as earth dolly complete all as specified and as directed by Engineer-in-Charge.

Taking down old damaged cable and Supply and lay cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core laid in duct / along pole/ wall etc including making connection omplete all as specified and as directed by Engineer-in-Charge. Note:The cost of Al thimblestugs and cable gland etc is incl in quoted rates and no extra payment will be made for it.

Material and Labour for Earthing complete with MS plate electrode of size 600 x 600 x 6 mm buried directly and preferably vertically in ground (earth pit not less than 2.25 mtrs deep below ground level ) with top edge of the plate not less than 1.5 Mtrs below ground level connected to earth strip 25x4 mm galvanized MS strip by means of check nuts, bolts, washers etc all as shown in electrical plate No. 5 of SSR Part-1 connected to Earthing test point including earth work, 1:3:6 C1 PCC chamber, 1:2:4 B1 PCC cover with 8 mm dia steel bars at 100 mm C/C suitable size of GI pipe for earth lead protection and watering, water funnel complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 25x4mm Gl earth continuity conductor or main earthing lead fixed to wall or buried in ground or drawn in conduit/ pipe or fixed to transformer/panel body complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc: as required 4mm dia galvanised iron or steel wire alongwith 20mm GI pipe light grade for protection complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. Make - Legrand cat No 607731 or equivalent in siemens/GE (Note : The cost of removing old wooden box and making good of surface i.e. brick work, plastering etc is included in quated rate) complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting VTPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. Make - Legrand or equivalent in siemens/GE (Note : The cost of removing old wooden box and making good of surface i.e. brick work, plastering etc is included in quated rate)

Supply and fixing MCCB FP 100 Amps, 25 KA Rupturing capacity complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement of MCB,SPN 6 to 40 Amps capacity, C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as specified and as directed by Engineer-in-Charge.

Supply and fix ceiling fan iron clamp of appropriate size for fixing the fans on angle iron as per site requirement complete all as specified and as directed by Engineer-in-Charge.

Supply , fixing, testing in repairs of JEF ECO SAFE Maintenance Free Grounding Solution set comprising of High tensile low carbon steel rod of 3 Mts length & 25 mm dia with 250 micron ( averaSchneider ) molecularly bonded copper on the outer surface to confirm with requirements of UL467 along with Back-fill compound strictly be a Carbon based conductive concrete type which has a resistivity of less than 0.12 Ohm Mtr as per Clause 14.5D of IEEE : 80 standard. Back-fill compound should be electronically conductive ( Like in metals ) and should not depend on moisture for conduction. JEF Powerfill Loresco compound shall be supplied in 50 Pound Bag. ( 1 Bag of 50 Pounds required per earthing set). Back-fill comound should be environment friendly, should solidify when mixed with water and set like concrete and should not leach / diffuse into the ground. A suitable earth terminaton clamp should also be supplied along with the set alongwith earth pit weatherproof incl complete all as specified and as directed by Engineer-in-Charge. Note : Back-fill compund shall not be mixed with any soil while pouring in the bore hole.

ROHIT CONSTRUCTION

RAJENDRA CONSTRUCTION

Shree Ayyappa Engineering

M/s S.D Construction Co

Shetty Construction Co