REPAIR AND MAINT TO DRAINAGE, COMPOUND WALL, CHAIN LINK FENCE, HARDSTANDING, DRAIN COVER AND CERTAIN MISC WORK IN UNRESTRICTED AND RESTRICTED AREA OF 506 ABW AND CLEANING OF SEWAGE TANK, SOAK WELL MANHOLES AND OTHER MISC WORKS OF COD AND 506 ABW

UNRESTRICTED AREA

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework & precast concrete articles. Complete all as specified and directed.

M & L for brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed

Labour only for Brickwork with Sub class B bricks ,straight or curved on plan exc 6m mean radius including built in 1:6 cement mortar . Complete all as specified & directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. Complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of wall in CM 1:6 and to be finished even and smooth (without using extra cement). Complete all as specified and directed.

M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & applying three coat of white wash on prepared brick work or concrete surfaces. Complete all as specified and directed.

M&L for Heavy Duty Vitrified Parking Ceramic tiles( 8-9 mm thick (Square/Rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc., set & jointed in neat cement slurry & pointed in white or coloured cement to match over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified & directed.

Demolition of Cement Concrete (unreinforced) of any description & in any position not otherwise specifically provided for. Complete all specified and directed.

M&L for Cement Concrete Type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete. Complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering & consolidation. Complete all as specified and directed.

M&L for Hardcore of broken stone or boulders of gauge not exc. 63 mm, deposited, spread & levelled in layers not exc. 15 cm thick, watered & rammed to a true surface. Complete all as specified & directed.

M&L for coloured rubber moulded chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick, set, jointed & pointed in neat cement slurry in floors with grey cement & pigment over & including 20 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed.

M&L for Glazed Coloured Ceramic Tiles 350 x 250 x 7-8 mm/450 x 350 x 7-8 mm thick in vertical surface such as dado/skirting/risers to steps,coloumn,fountains etc, set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including rendering 10 mm thick in cement mortar 1:4 complete all as specified and directed.

Labour only for for Machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658 - 2006 of 80 mm thickness M-40 Grade with grey cement & no pigment. Complete all as specified and directed.

Labour only for Machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658 - 2006 of 60 mm thickness M-35 Grade with grey cement & no pigment. Complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658 - 2006 of 80 mm thickness M-40 Grade with grey cement & no pigment. Complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658 - 2006 of 60 mm thickness M-35 Grade with grey cement & no pigment. Complete all as specified and directed.

M&L for 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. Complete all as specified and directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform & other similar situations. Complete all as specified and directed.

M & L For Cement concrete work in pavement/hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less complete all as specified and directed

M & L for Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound,GRADE A complete all as specifed and directed

M & L For Forming Contraction (Dummy) joints 100 mm deep x 10mm wide, filled with sealing compound,GRADE A complete all as specifed and directed

M & L For Polythene film, black 150micron laid in floors complete all as specified and directed

Excavation in trenches in soft/loose soil, not exceeding 1.5 metre wide & not exceeding 1.5 metre in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan & getting out complete all as specified & directed.

Excavating over areas, not exceeding 1.5m deep and getting out in soft/loose soil complete all as specified & directed.

M&L for Moorum/Red Bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled & rammed including watering. Complete all as specified & directed.

M&L for Cement Concrete Type B-1, 1:2:4 using 20 mm graded stone aggregate as in surface channels & drains. Complete all as specified & as directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. Complete all as specified and directed.

Add or Deduct for each 25 mm girth or part thereof over or under 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. Complete all as specified and directed.

M&L for providing Cement Concrete Type B-1, 1:2:4 using 20 mm graded stone aggregate as in lintels upto 1.5 m clear span, cills, steps; seismic & other similar bands, plinth courses, string courses, lacing courses, parapets & railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs & the like including weathering, slightly rounded or chamfered angles and throating including necessary form work. Complete all as specified and directed.

Demolition of Cement Concrete (reinforced) of any description & in any position not otherwise specifically provided for. Complete all specified and directed.

M&L for Providing Precast Cement Concrete Type B-1, 1:2:4 using 20mm graded stone aggregate in landings, cover slabs (for manholes etc.), chullah hoods, chajjas, water troughs, mangers, shelves & similar articles with plain faces including necessary chamfers, weatherings, throating etc. & setting in 1:6 cement mortar including necessary formwork if required. Complete all as specified & as directed.

M&L for Returning, filling in soft/loose soil, including spreading, levelling, watering and well ramming in layers not exc 25 cm. Complete all as specified & directed.

M&L for Removing surplus excavated material (soil) to a distance not exceeding 50 metre & depositing where directed at a level not exceeding 1.5 metre above the starting point. Complete all as specified & directed.

Demolition & breaking up of 300 mm Internal dia, drain pipes (Salt glazed ware, AC or Reinforced Concrete) set in cement mortar. Complete all as specified and directed.

Demolition & breaking up of 450 mm Internal dia, drain pipes (Salt glazed ware, AC or Reinforced Concrete) set in cement mortar. Complete all as specified and directed.

M&L for Reinforced Cement Concrete Pipes, Class NP3, 300 mm bore laid & jointed complete with collars. Complete all as specified & directed.

M&L for Reinforced Cement Concrete Pipes, Class NP3, 450 mm bore laid & jointed complete with collars. Complete all as specified & directed.

M&L for Cement Concrete bed Type C-2, 1:3:6 (using 40 mm graded stone aggregate) to 300 mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified & directed.

M&L for Cement Concrete bed Type C-2, 1:3:6 (using 40 mm graded stone aggregate) to 450 mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified & directed.

Dismantling posts or sturts (wood, steel or R.C.C.) any section embedded in concrete, brickwork, masonry, etc., including taking out embedded portion and making good disturbed ground. Complete all as specified and directed.

Dismantling fencing wire mesh, any type. Complete all as specified and directed.

Excavation in post holes (or similar holes) each not exceeding 0.50 cum in soft/loose soil, getting out, returning, filling in & ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering & removing surplus soil to a distance not exceeding 50 m & making good surface. Complete all as specified & directed.

M&L for Cement Concrete Type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete. Complete all as specified & directed.

S&F of Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, driiling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165. Complete all as specified & directed.

S&F of mild steel round bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to Fe-410-W (Gde E-250) quality-A or Fe-290 (Gde-E-165). Complete all as specified & directed.

S&F of Mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5 cm but not exc 10 cm long, diameter of neck 11 to 15 mm. Complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc., including provision of binding wire. Complete all as specified and directed.

Supply only Chain link MS galvanised fencing any size or type. Complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description, not exc 10 cm in width or girth when unconnected with other painting or when painted in a different tint & apply two coat of synthetic enamel paint (ordinary tint) over & including one coat of red oxide, zinc chrome primer. Complete all as specified & as directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth, not otherwise described & applying two coat of synthetic enamel paint (ordinary tint) over & including one coat of red oxide, zinc chrome primer. Complete all as specified and directed.

S&F in repair, Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc., as directed (each line wire to be measured). Complete all as specified & as directed.

M&L for Providing precast cement concrete louvres and jallies, 35 mm thick (measured solid), Type B-0, 1:2:4 (using 12.5 mm graded aggregate) including all mouldings but excluding frame, set in 1:6 cement mortar including necessary formwork if required. Complete all as specified and directed.

S&F in repair, Steel Concertina Coil of super profile of 600 mm dia stress in position hot dipped Galvanised steel wire coated with CLR anti corrosive paint making diamond shape with the help of dove tail clip (18 SWG) the coil fixed with razor wire at points were coil touch the bottom layer wire with help of hog rings (14 SWG) with and including all fittings like fastener, clips, luggs rings etc as approved by Engr-in Charge. Complete all as specified and directed.

M&L for Form Work to faces of walls, retaining walls,foundations, abutments, parapets & staircase railings & similar work including attached pillasters, buttresses, etc., vertical or to batter, fair finished flat surfaces of concrete. Complete all as specified and directed.

M&L for RCC M25 Design Mix in walls, retaining walls, basement walls, ballast walls & the like; any thickness; above top of footings; including attached pillasters & buttresses. Complete all as specified and directed.

M & l for RCC M 25 Design Mix for foundations including rafts , footings, foundation beams , plinth beams bases for coloumn etc basement slab under reamed piles and mass concrete complete all as specified and directed

M&L RCC M-25 design mix using 20 mm graded aggregate in Columns, pillars, piers, posts and struts Complete all as specified and directed

M & L for Form work to side of columns and similar work with fair finished surface complete all as directed.

S&F of Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. Complete all as specified and directed.

S&F of Mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. Complete all as specified and directed.

S&F of Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165. Complete all as specified and directed.

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc., complete drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete quality conforming to Fe 410-W (Gde-E-250) quality-A. Complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete

Dismantling wrought iron or mild steel work of any description not otherwise provided for. Complete all as specified & directed.

Providing and fixing 4 mm thick ACP Sheet cladding of approved make,shade and colour,consisting of 0.5 mm thick aluminium sheets bondedwith LDPE core,Fixed on aluminium frame system with necessary cleats,angles, nuts,bolt & All fixing and scafffolding height upto 10.5 m ,complete in all respect as per drawing and direction of Engineer in charge

M&L for Demolition and breaking up 150 mm internal dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortor. Complete all as specified and directed.

M&L for Demolition and breaking up 200 mm internal dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortor. Complete all as specified and directed.

M&L for Demolition and breaking up 300 mm internal dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortor. Complete all as specified and directed.

Supply, laying & jointing 150 mm nominal bore (Internal Diameter) DWC (HDPE Double Wall Corrugated) Pipe, socketed & sewage pipe having 6.00 metre length, conforming to IS : 16098 (Part-II) of SN-4 Stiffness with & including necessary jointing materials etc. Complete all as specified & directed.

Supply, laying & jointing 200 mm nominal bore (Internal Diameter) DWC (HDPE Double Wall Corrugated) Pipe, socketed & sewage pipe having 6.00 metre length, conforming to IS : 16098 (Part-II) of SN-4 Stiffness with & including necessary jointing materials etc. Complete all as specified & directed.

Supply, laying & jointing 300 mm nominal bore (Internal Diameter) DWC (HDPE Double Wall Corrugated) Pipe, socketed & sewage pipe having 6.00 metre length, conforming to IS : 16098 (Part-II) of SN-4 Stiffness with & including necessary jointing materials etc. Complete all as specified & directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150 mm internal dia of pipe. Complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 200 mm internal dia of pipe. Complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 300 mm internal dia of pipe. Complete all as specified and directed.

M&L for Cement Concrete bed Type C-2, 1:3:6 (using 40 mm graded stone aggregate) to 150 mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested. Complete all as specified & directed.

M&L for Cement Concrete bed Type C-2, 1:3:6 (using 40 mm graded stone aggregate) to 200 mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested. Complete all as specified & directed.

Blank.

M&L in repair Salt glazed stone ware gully traps size 150 x 150 mm, square or round mouthed, type ‘P’ including setting and jointing to drains with cement mortar 1:1 including demolition of existing traps. Complete all as specified and directed.

M&L for Cleaning of sewage line (length from manhole to manholes) of any dia by roding and flushing after cleaning and removing mud/sludge etc to a distance exceeding 250 metre but not exceeding 500 metre and spreading in low laying areas and covering with loose soil. Complete all as specified and directed.

M&L for Cleaning of manholes and removing mud/sludge from manholes of any size and depth and removing mud/sludge etc to a distance exceeding 250 metre but not exceeding 500 metre, deposing the sludge and spreading in low laying areas and covering with loose soil. Complete all as specified and directed.

M&L for Cleaning the blockage of WC, floor trap, nahani trap, gully trap and first manhole and removing sludge to a distance exceeding 250 metre but not exceeding 500 metre, deposing the sludge and spreading in low laying areas and covering with loose soil. Complete all as specified and directed.

M&L for cutting all grass, vegetation & wild bushes, surface dressing around the Septic Tank/Soak Well/Manholes to a distance of 2 metre all around and removing excavated material to a distance not exceeding 50 metre & depositing where directed at a level not exceeding 1.5 metre above the starting point. Complete all as specified and directed.

M&L for Cleaning and removing shrubs plants from roof, chajja, facia or brick wall complete with roots and providing anti vegitation growth chemical spray at any height and making good in CM 1:4. Complete all as specified and directed. Note : All vegetation & plants including their roots for the particular area shall be totally removed. Any damage to the surface shall be repaired either by Plaster in CM 1:4 & Brick Work in CM 1:6 or PCC type B-1, 1:2:4 (using 20 mm graded stone aggregate) as on required basis. Unit rate quoted to be deemed inclusive of these aspects.

RESTRICTED AREA

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework & precast concrete articles. Complete all as specified and directed.

M & L for brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed

Labour only for Brickwork with Sub class B bricks ,straight or curved on plan exc 6m mean radius including built in 1:6 cement mortar . Complete all as specified & directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. Complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of wall in CM 1:6 and to be finished even and smooth (without using extra cement). Complete all as specified and directed.

M&L for preparation of newly plastered or unplastered brick work or concrete surfaces & applying three coat of white wash on prepared brick work or concrete surfaces. Complete all as specified and directed.

M&L for Heavy Duty Vitrified Parking Ceramic tiles( 8-9 mm thick (Square/Rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc., set & jointed in neat cement slurry & pointed in white or coloured cement to match over & including 15 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified & directed.

Demolition of Cement Concrete (unreinforced) of any description & in any position not otherwise specifically provided for. Complete all specified and directed.

M&L for Cement Concrete Type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete. Complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering & consolidation. Complete all as specified and directed.

M&L for Hardcore of broken stone or boulders of gauge not exc. 63 mm, deposited, spread & levelled in layers not exc. 15 cm thick, watered & rammed to a true surface. Complete all as specified & directed.

M&L for coloured rubber moulded chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick, set, jointed & pointed in neat cement slurry in floors with grey cement & pigment over & including 20 mm thick screed bed or bedding layer of 1:6 cement mortar for laying floor finishes. Complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed.

M&L for Glazed Coloured Ceramic Tiles 350 x 250 x 7-8 mm/450 x 350 x 7-8 mm thick in vertical surface such as dado/skirting/risers to steps,coloumn,fountains etc, set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including rendering 10 mm thick in cement mortar 1:4 complete all as specified and directed.

Labour only for for Machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658 - 2006 of 80 mm thickness M-40 Grade with grey cement & no pigment. Complete all as specified and directed.

Labour only for Machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658 - 2006 of 60 mm thickness M-35 Grade with grey cement & no pigment. Complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658 - 2006 of 80 mm thickness M-40 Grade with grey cement & no pigment. Complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658 - 2006 of 60 mm thickness M-35 Grade with grey cement & no pigment. Complete all as specified and directed.

M&L for 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. Complete all as specified and directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform & other similar situations. Complete all as specified and directed.

M & L For Cement concrete work in pavement/hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less complete all as specified and directed

M & L for Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound,GRADE A complete all as specifed and directed

M & L For Forming Contraction (Dummy) joints 100 mm deep x 10mm wide, filled with sealing compound,GRADE A complete all as specifed and directed

M & L For Polythene film, black 150micron laid in floors complete all as specified and directed

Excavation in trenches in soft/loose soil, not exceeding 1.5 metre wide & not exceeding 1.5 metre in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan & getting out. Complete all as specified & directed.

Excavating over areas, not exceeding 1.5m deep and getting out in soft/loose soil complete all as specified & directed.

M&L for Moorum/Red Bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled & rammed including watering. Complete all as specified & directed.

M&L for Cement Concrete Type B-1, 1:2:4 using 20 mm graded stone aggregate as in surface channels & drains. Complete all as specified & as directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. Complete all as specified and directed.

Add or Deduct for each 25 mm girth or part thereof over or under 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. Complete all as specified and directed.

M&L for providing Cement Concrete Type B-1, 1:2:4 using 20 mm graded stone aggregate as in lintels upto 1.5 m clear span, cills, steps; seismic & other similar bands, plinth courses, string courses, lacing courses, parapets & railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs & the like including weathering, slightly rounded or chamfered angles and throating including necessary form work. Complete all as specified and directed.

Demolition of Cement Concrete (reinforced) of any description & in any position not otherwise specifically provided for. Complete all specified and directed.

M&L for Providing Precast Cement Concrete Type B-1, 1:2:4 using 20mm graded stone aggregate in landings, cover slabs (for manholes etc.), chullah hoods, chajjas, water troughs, mangers, shelves & similar articles with plain faces including necessary chamfers, weatherings, throating etc. & setting in 1:6 cement mortar including necessary formwork if required. Complete all as specified & as directed.

M&L for Returning, filling in soft/loose soil, including spreading, levelling, watering and well ramming in layers not exc 25 cm. Complete all as specified & directed.

M&L for Removing surplus excavated material (soil) to a distance not exceeding 50 metre & depositing where directed at a level not exceeding 1.5 metre above the starting point. Complete all as specified & directed.

Dismantling posts or sturts (wood, steel or R.C.C.) any section embedded in concrete, brickwork, masonry, etc., including taking out embedded portion and making good disturbed ground. Complete all as specified and directed.

Dismantling fencing wire mesh, any type. Complete all as specified and directed.

Excavation in post holes (or similar holes) each not exceeding 0.50 cum in soft/loose soil, getting out, returning, filling in & ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering & removing surplus soil to a distance not exceeding 50 m & making good surface. Complete all as specified & directed.

M&L for Cement Concrete Type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete. Complete all as specified & directed.

S&F of Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, driiling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165. Complete all as specified & directed.

S&F of mild steel round bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to Fe-410-W (Gde E-250) quality-A or Fe-290 (Gde-E-165). Complete all as specified & directed.

S&F of Mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5 cm but not exc 10 cm long, diameter of neck 11 to 15 mm. Complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc., including provision of binding wire. Complete all as specified and directed.

Supply only Chain link MS galvanised fencing any size or type. Complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description, not exc 10 cm in width or girth when unconnected with other painting or when painted in a different tint & apply two coat of synthetic enamel paint (ordinary tint) over & including one coat of red oxide, zinc chrome primer. Complete all as specified & as directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth, not otherwise described & applying two coat of synthetic enamel paint (ordinary tint) over & including one coat of red oxide, zinc chrome primer. Complete all as specified and directed.

S&F in repair, Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc., as directed (each line wire to be measured). Complete all as specified & as directed.

M&L for Providing precast cement concrete louvres and jallies, 35 mm thick (measured solid), Type B-0, 1:2:4 (using 12.5 mm graded aggregate) including all mouldings but excluding frame, set in 1:6 cement mortar including necessary formwork if required. Complete all as specified and directed.

S&F in repair, Steel Concertina Coil of super profile of 600 mm dia stress in position hot dipped Galvanised steel wire coated with CLR anti corrosive paint making diamond shape with the help of dove tail clip (18 SWG) the coil fixed with razor wire at points were coil touch the bottom layer wire with help of hog rings (14 SWG) with and including all fittings like fastener, clips, luggs rings etc as approved by Engr-in Charge. Complete all as specified and directed.

M&L for Form Work to faces of walls, retaining walls,foundations, abutments, parapets & staircase railings & similar work including attached pillasters, buttresses, etc., vertical or to batter, fair finished flat surfaces of concrete. Complete all as specified and directed.

M&L for RCC M25 Design Mix in walls, retaining walls, basement walls, ballast walls & the like; any thickness; above top of footings; including attached pillasters & buttresses. Complete all as specified and directed.

M & l for RCC M 25 Design Mix for foundations including rafts , footings, foundation beams , plinth beams bases for coloumn etc basement slab under reamed piles and mass concrete complete all as specified and directed

M&L RCC M-25 design mix using 20 mm graded aggregate in Columns, pillars, piers, posts and struts Complete all as specified and directed

M & L for Form work to side of columns and similar work with fair finished surface complete all as directed.

S&F of Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. Complete all as specified and directed.

S&F of Mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. Complete all as specified and directed.

S&F of Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165. Complete all as specified and directed.

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc., complete drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete quality conforming to Fe 410-W (Gde-E-250) quality-A. Complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete

Dismantling wrought iron or mild steel work of any description not otherwise provided for. Complete all as specified & directed.

Providing and fixing 4 mm thick ACP Sheet cladding of approved make,shade and colour,consisting of 0.5 mm thick aluminium sheets bondedwith LDPE core,Fixed on aluminium frame system with necessary cleats,angles, nuts,bolt & All fixing and scafffolding height upto 10.5 m ,complete in all respect as per drawing and direction of Engineer in charge

M&L for Demolition and breaking up 150 mm internal dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortor. Complete all as specified and directed.

M&L for Demolition and breaking up 200 mm internal dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortor. Complete all as specified and directed.

M&L for Demolition and breaking up 300 mm internal dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortor. Complete all as specified and directed.

Supply, laying & jointing 150 mm nominal bore (Internal Diameter) DWC (HDPE Double Wall Corrugated) Pipe, socketed & sewage pipe having 6.00 metre length, conforming to IS : 16098 (Part-II) of SN-4 Stiffness with & including necessary jointing materials etc. Complete all as specified & directed.

Supply, laying & jointing 200 mm nominal bore (Internal Diameter) DWC (HDPE Double Wall Corrugated) Pipe, socketed & sewage pipe having 6.00 metre length, conforming to IS : 16098 (Part-II) of SN-4 Stiffness with & including necessary jointing materials etc. Complete all as specified & directed.

Supply, laying & jointing 300 mm nominal bore (Internal Diameter) DWC (HDPE Double Wall Corrugated) Pipe, socketed & sewage pipe having 6.00 metre length, conforming to IS : 16098 (Part-II) of SN-4 Stiffness with & including necessary jointing materials etc. Complete all as specified & directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150 mm internal dia of pipe. Complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 200 mm internal dia of pipe. Complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 300 mm internal dia of pipe. Complete all as specified and directed.

M&L for Cement Concrete bed Type C-2, 1:3:6 (using 40 mm graded stone aggregate) to 150 mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested. Complete all as specified & directed.

M&L for Cement Concrete bed Type C-2, 1:3:6 (using 40 mm graded stone aggregate) to 200 mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested. Complete all as specified & directed.

M&L for Cement Concrete bed Type C-2, 1:3:6 (using 40 mm graded stone aggregate) to 300 mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested. Complete all as specified & directed.

M&L in repair Salt glazed stone ware gully traps size 150 x 150 mm, square or round mouthed, type ‘P’ including setting and jointing to drains with cement mortar 1:1 including demolition of existing traps. Complete all as specified and directed.

M&L for Cleaning of sewage line (length from manhole to manholes) of any dia by roding and flushing after cleaning and removing mud/sludge etc to a distance exceeding 250 metre but not exceeding 500 metre and spreading in low laying areas and covering with loose soil. Complete all as specified and directed.

M&L for Cleaning of manholes and removing mud/sludge from manholes of any size and depth and removing mud/sludge etc to a distance exceeding 250 metre but not exceeding 500 metre, deposing the sludge and spreading in low laying areas and covering with loose soil. Complete all as specified and directed.

M&L for Cleaning the blockage of WC, floor trap, nahani trap, gully trap and first manhole and removing sludge to a distance exceeding 250 metre but not exceeding 500 metre, deposing the sludge and spreading in low laying areas and covering with loose soil. Complete all as specified and directed.

Schedule of credit amount of Rs. 2,76,170.00 to be deducted during AOC

Please Enable Macros to View BoQ information