PROVN OF TWO TOILET BLOCKS AT GHASI RAM STADIUM OF MRC AND SPECIAL REPAIRS TO BLDG NO. T 20 AT MH UNDER GE SAUGOR

Amount

S&F pre- coated galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa (AZ150) as in roof covering/ clading to wall, including crimping sheet at end fixed with self tapping screws including dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F pre- coated galvalume aluminum zinc coating GI based profile ridge steel sheet of 0.50 mm thick of any colour having tensile strength of 550 mpa (AZ150) as in ridges, roof covering/ clading to wall, fixed with self tapping screws including dismantling of Asbestos cement (corrugated, semicorrugated, etc.) as in ridge sheet complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position and removing to store complete all as specified and directed.

M&L for second class hard wood as in scantling, wrought, timber unframed and fixed complete all as specicifed and directed.

S&F mild steel rolled section conforming to Fe-290 (Gde E-165), angle or tee section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters fixed with angle cleats and other connecting plates etc. complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide or zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

Demolition of cement concrete not exc 15 cms thick below or above ground level as in floor Paving etc including removal of demolished material from work complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) as in plinth protection finishing cement concrete surfaces even & smooth without using extra cement including forming construction joint of size 10mm x 20mm filled with bitumen and sand mortar complete all as specified and directed..

Dismantling of floor, hearth or wall tiles / terrazo including cement mortar bedding, removal servicable tiles to store and rubbish off the premises complete all as specified and directed.

M&L PCC 1:2:4, type B-0 (using 12.5mm graded stone aggregate) 25mm thick as in floor finishes complete all as specicifed and directed.

M&L for mirror polished machine cut Kota stone slab flooring 20mm to 22 mm thick size not less than 550mm X 550mm laid over and including 20mm thick screed in CM(1:4) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed.

M&L for Kota stone slab 12mm to 15 mm thick as in skirting laid over 15mm thick plater in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed.

M&L for non-skid coloured ceremic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specfied and directed.

M&L for glazed coloured ceremic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in skirting, dado set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10mm thick rendering in CM (1:4) complete all as specfied and directed.

M&L for glazed ceremic tiles of size 600mm x 300mm x 7mm thick as in vertical surfaces such as skirting, dao, etc set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10 mm thick rendering in CM (1:4) complete all as specfied and directed.

M&L for non-skid coloured ceremic tiles 7mm to 8 mm thick (Square/ rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specfied and directed.

M&L for 100 mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregates) as in sub base, mass concrete filling, etc., complete all as specified and directed.

M&L for machine pressed precast cement concrete coloured chemically treated interlocking paver block any shape and size conforming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment laid over and including 40mm thick uniformly levelled surface of stone dust cushioning complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks, straright or corved on plan exc 6m mean radius built in Cement mortar 1:6 including demolition of brick work and stone/ boulder masonary built in cement mortar and lime mortar complete all as specified and directed.

All as per Srl item No 19 as above but except bricks including demolition of brick work and stone/ boulder masonary built in cement mortar and lime mortar complete all as specified and directed.

M&L for rendering 15mm thick on other than fair face of brickwork or concrete surfaces in cement mortar 1:4 complete all as specicifed and directed.

Taking down cement plaster on brick wall etc including racking out joints hacking for key, scrubbing down with water as described complete all as specicifed and directed.

M&L for rendering 15mm thick on brick wall or concrete surface in cement mortar 1:6 on other than fair faces of brick work surface finished fair and even complete all as specicifed and directed.

M&L for rendering 15mm thick on brick wall or concrete surface consisting two layers, under layer of 10mm thick in CM (1:6) & top layer of 5mm thick in cement mortar 1:4 mixed with water proofing compound, finished even and smooth without using extra cement complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid saperately.)

Supply only liquid water proofing compound complete all as specified and directed

M&L for applying two coats of exterior emulsion weather proof paint over one coat of exterior wall primer on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified and directed. Make Asian ACE or equivalent.

M/L for preparation of new plaster surface of wall and applying two coat of distemper oil emulsion white or over a coat of white wash complete all as specicifed and directed.

M&L for applying two coat of distemper oil emulsion white or tinted over a layer of wall putty on old decorated or undecorated wall surface including preparation of surfaces by washing rubbing down and stoping of distempered and painted surfaces complete all as specified.

M&L for one coat of synthetic enamel paint on old painted wood/wood based surface of any desription over 10cm width or girth incl preparation surfaces such as removing all splashes, drops, dirt and leaving premisesin a clean state complete all as specified and directed

M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:1 complete all as specified and directed.

M&L for 18 mm to 20 mm thick Granite slab of any shade ( table rubbed and polished ) machine cut for floor /shelves in steps, jambs, pillars, window cills& cooking plateforms over 15 mm thick cement mortor 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match shade of the slabs laid bedded and pointed in any mortor complete all as specified & directed

S&F in repairs 1000 ltr capacity of rotational moulded polyethyline water storage tank (Cylindrical vertical with closed top) three layered wall construction hoisted & fixed in position including S&F 20mm dia GI Pipe medium grade washout pipe 450mm long with plug & 20mm dia GI pipe medium grade overflow pipe 600 mm long with fittings including 01 Nos 20/25mm float valve complete all as specified and directed.

S&F medium grade galvanised steel tubing of 15mm bore with all fittings fixed to wall or laid in floors including taking up or down steel tubing and connections complete all as specicifed and directed.

S&F medium grade galvanised steel tubing of 20mm bore with all fittings fixed to wall or laid in floors including taking up or down steel tubing and connections complete all as specicifed and directed.

S&F in repairs 15 mm dia bib tap cast copper alloy (fancy type), chromium plated, 'with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specicifed and directed.

S&F in repairs 75 mm size brass chormium plated shower rose fancy type including fixing to steel pipe or union complete all as specified and directed

S&F in repairs stop valve, cast copper alloy, fancy type,chromium plated with long shank and cup (Concealed type), screwed down both ends for high pressure, as per ISI suitable for 15mm dia iron pipe complete all as specicifed and directed.

S&F in repairs 20mm dia brass chromium plated tubular towel rails, D type, 60cm long between flanges, complete all as specicifed and directed.

S&F in repairs 125mm to 175mm hat pegs of aluminium, solid body fixed with screws complete all as specicifed and directed.

S&F in repairs Shelf of PTMT (Minimum weight 300 gm) including chromium plated brass screws and wooden/ plastic cleats complete all as specicifed and directed.

S&F in repairs 20mm dia gun metal globe or gate valve with iron wheel screwed bothedns for iron pipe of 20 mm dia complete all as specicifed and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden or steel frames complete all as specified and directed

M&L for sheet glass ordinary quality 3mm thick and glazing with oil putty in squares n.exc. 0.5 sqm each pane complete all as specicifed and directed.

S&F in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanesed wire stapels complete all as specifed and directed.

Taking down existing flushing cistern of any type and any capacity complete all as specified and directed

S&F 10 ltrs capacity (PVC), valve less, syphonic action type, fluhsing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe complete all as specified and directed.

Taking down chowkat with shutter n.exc 1.5 sqm each (without taking off shutters from the frame) and removing to store yard complete all as specified and directed.

Taking down chowkat with shutter exc 1.5 sq.m but n.exc 4 Sqm each and removing to store yard complete all as specified and directed.

S&F second class hard wood plain, solid, straight, chowkat and frames, wrought, framed rebated on the solid, rounded or chamfered,put together with glue pinned at joints complete all as specicifed and directed.

M&L for preparing surface of wood and wood based material and steel and iron work of any description and girth and treating ends of post, back of chowkats etc, area exc. 0.1 sqm and n.exc. 0.5sqm, with tar or coal tar or black paint complete all as specified and directed.

S&F 35mm thick flush shutters , solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed

S&F 35mm thick second class hardwood factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc divided into panels with plain or mitered shash bars any numbers of panels, edges of framing plain, chemfered or rounded, fitted with cut and mitred beads for securing glass complete all as specified and directed.

S&F solid PVC frame (single rebated) of size 50mmx47mm made out of 5mm prelam PVC sheet used instead of plain colour PVC sheet and edges will be painted to match with prelam sheet and reinforced with mild steel square tube complete all as specified and directed

S&F factory made soild PVC moulded door shutter, 28mm to 30 mm thick (stiles) with wood free EPS with 2, 4 or 6 raised panel design with 4mm thick moulded prelam PVC sheet on the front face & 4mm thick plain colour sheet on back face, supplying & fixing in frame at site as per specification and drawings complete all as specified and directed..

S&F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanesed wire stapels complete all as specifed and directed.

S&F aluminium barrel tower bolt,stove enamelled black, with bright bolt and fixed 200mm long complete all as specicifed and directed.

S&F Alluminium alloy anodised,sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet,cast ortruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed 300mm long complete all as specicifed and directed.

S&F 100 mm size MS butt hinges medium weight cold rolled fixed/ welded to frame complete all as directed.

S&F 125 mm size aluminium handles,cast type,anodised complete all as specified and directed.

S&F150 mm long,aluminium,anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 125 mm size MS butt hinges medium weight cold rolled fixed/ welded to frame complete all as directed.

S&F 150mm size aluminium handles,cast type,anodised complete all as specicifed and directed.

S&F mild steel bands,straps, supports or stays for rainwater pipes, soil/waste or vent pipes including bolts, if required, hold fast and similar small articles conforming to Fe 290 Gde E-165 complete all as specicifed and directed.

S&F mild steel work as in wind ties for roof including ) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

S&F mild steel framed work such as grills gratings, sunshed cover fixed with nut bolts incl,cutting drilling holes etc., with ends of bars shouldered and/ or riveted, similar work conforming to Fe 290 gde E 165 complete all as specified and directed.

S&F mild steel framed work as in doors or gates designer type of any section with gusset plates, rails, braces etc, complete, drilled for fixing of steel sheeting or other covering confirming to Fe 290 (Gde E 165) . Door, etc to be prepared for hanging or sliding with and including, either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete all as specicifed and directed.

S&F in repairs vitreous China WHB white flat back size 550mmx400mm including S&F angle iron brackets, C.P pillar tap fency type 01 No 15mm bore, CP waste coupling, 32mm dia and PVC waste pipe 32mm dia and PVC connection 450mm long high pressure complete all as specified & directed.

S&F in repairs angle valve, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down both ends for high pressure, as per ISI suitable for 15mm dia iron pipe complete all as specicifed and directed.

S&F in repairs 450mm long PVC connection 15mm bore with PTMT nuts complete all as specicifed and directed.

S&F in repairs vitreous China wash down water closet pan (pedestal pattern), coloured, with and including plastic water closet seat cover, coloured, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device, including cp jet spray, fixing bolts, connection to drain (or outgoing pipe) and to flushing pipe, anti -syphonage pipe, etc., complete all as specified and directed.

M&L for preparing surface of wood and wood based material and steel and iron work of any description and girth and treating small articles such as stops, holdfasts etc, area n.exc. 0.1sqm, with tar or coal tar or black paint complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint on old decorated wooden surfaces exc 10 cm width or girth, including preparation of surfaces, complete all as specified and directed.

S&F in repairs toilet paper holder of vitreous china, coloured, fixed to wall with chromium plated brass screws complete all as specified and directed.

S&F 110mm PVC(SWR) bends with access door any radius complete all as specified and directed.

S&F 110mm PVC(SWR) junction double, (double T) with access door any radius complete all as specified and directed.

S&F 110mm PVC(SWR) vent cowl complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75mm PVC(SWR) bends with access door any radius complete all as specified and directed.

S&F 75mm PVC(SWR) vent cowl complete all as specified and directed.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

M&L for complete removal of existing treatement and applying two coats of ACE on old decorated or undecorated wall surfaces including preperation of surfaces, complete all as specified.

M&L for suspended false ceilling comprising of non asbestos fibre cement bulding boards fixed or laid/inserted to GI frame work with screws over GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to sourrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fastners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm center to centre including hangers 6mmm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long including dismantling false ceiling any description or in any thickness, including cover fillets complete all as specified and directed.

S&F in repairs 300 mm, mild steel ordinary rat rail rod pattern springs including roller plate complete all as specified and directed.

M&L for preparing surface of wood and wood based material and steel and iron work of any description and girth and treating small articles such as stops, holdfasts etc, area n.exc. 0.1sqm, with tar or coal tar or black paint complete all as specified and directed.

S&F in repairs harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as speicifed and directed.

M&L for cutting chases, pinning in, in brick/ stone wall making good to facings where required and pointing in cement mortar 1:3 or PCC 1:2:4 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring insert sheet in wall. etc. and making good, cutting not exceeding 10cm girth complete all as specified and directed.

Surface Excavtion in soft/loose soil averaging 10 cm deep and getting out, complete all as specfied and directed.

Excavation over areas n.exc1.5m deep and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m deep in hard/ dense soil for foundation , etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5m in deptlh and getting out complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide and exc 1.5 m but n. exc 3.0 m deep in soft/disintegrated rock for foundation , etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5m in deptlh and getting out soil complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide and exc 1.5 m but n. exc 3.0 m deep in soft/disintegrated rock complete all as specified and directed.

M&L for approved earth filling with approved soil / morooum brought from out side MD land, filling in trenches or paving laid in layers not exceeding 25 cm thick spread, levelled and rammed including watering etc complete all as specified and directed.

Removing excavated materials (soil) to a distance n. exc 50 m and deposting where directed, at a level n.exc. 1.5m above the starting point complete all as specified and directed.

Returning filling in incl spreading, levelling, watering and well ramming in layers not exc 25cm complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregates) as in foundation filling and mass concrete complete all as specifed and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregates) as in foundation filling and mass concrete complete all as specifed and directed.

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregates as in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc basement slabs, under reamed plies and mass concrete, complete all as specified and directed

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregates as in Columns, pillars, piers, posts and struts and the like complete all as specified and directed.

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregates as in Beams, cantilevers, bressummers, lintels over 1.5m span and the like complete all as specified and directed.

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregates as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like and the like complete all as specified and directed.

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregates as in chajja and the like and the like complete all as specified and directed.

M&L for mild steel "TMT" bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending sprially for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with chips complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and directed.

All as per item 107 above but for 5mm dia and over upto 10 mm dia and including 10mm dia in stirrups, spacers and binders.

M&L for form work to sides & soffits of plinth beam and sides of footings getting for fair finished surfaces of concrete complete all as specified and directed.

M&L for form work to sides of pillars, posts, struts, piers, columns, etc as in fair finished surfaces of concrete complete all as specified and directed

M&L for formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. for fair finished surfaces of concrete flat complete all as specified and directed

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; n exc. 200mm thick (horizontal or sloping) Fair finished surfaces of concrete flat complete all as specified and directed

M&L for formwork to edges of concrete flats, breaks in floor, openings in concrete walls, floors and roofs not exceeding 20cm width for fair finished surfaces complete all as specified and directed.

M&L for brick work with fly ash modular bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for brick work with fly ash modular bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed.

M&L for brick work with old size sub class 'B' bricks in one brick thick honey comb walling, built in CM (1:6) complete all as specified and directed.

M&L for brick bats for laying in soakage pit complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:2:4, type B-0 (using 12.5mm graded stone aggregate) as in mud stops, roof top as a leveling course / padding to maintain the slope,finished the surface even and smooth without using extra cement, complete all as specified & as directed .

M&L for provn of water proffing roof treatment to RCC roof with approved modified membrane of weighing not less than 3 kg/sqm comprising with following items and all as specified as under:-

10mm thick plastering in CM(1:4) mixed with WPC @ 3% by weight of cement applied over roof slab Note:- WPC shall be measured and paid separately

The surface of roof,parpet and gutters drain mouths etc over which water proofing treatment is to be applied shall be cleaned of all foreign matter such as fungus,mass dust etc by wire brushing & dusting and a groove shall be cut for cast iron drain outlets

Oil based Bitumen primer conforming to IS-3384-1986 @ 0.3 kgs per sqm to be applied on prepared surface till the surface is properly impregnated.

Applying one coat of hot blown grade bitumen 85/25 grade @ 1.20 kg/Sqm

Laying of water proofing teratment of weight not less than 3 Kg / sqm APP modified polymeric water proofing membrane composed of 100 micron (+10% ) high density polyethylene sheet ( HMHDPE) as center core, which is standwiched between high quality polymeric bitumen mix having softening , high heat resistance and cold flexible protected on either side with a thin thermo fusible HMHDPE film with side and laps 75 mm and 100 mm as per manufacture instruction etc.

Applying one coat of hot blown grade bitumen 85/25 grade @ 1.20 kg/Sqm over the membrane

Applying aluminium paint in two coat @ 100 gm/sqm in each coat on finished membrane surfaces

M&L for coloured non skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM(1:6) complete all as specified and directed

M&L for brick work with sub class 'B' bricks old size, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 450mm x 300mm x 7mm thick as in vertical surfaces such as skirting, dado, etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick plaster in CM (1:4) complete all as specified and directed

S&F pressed steel frames of size 105mm x 60mm with one or more rebates including necessary fixing lugs hinges, locks strike plate etc(thickness of sheet shall be 1.25mm) and making good the plaster of wall in CM 1:6 including filling with PCC 1:3:6 type C-0 (using 12.5mm grade stone aggregates) as in filling of chowkhats or pressed steel door frame complete all as specified and directed.

M&L for sanding newly tarred or painted surfaces with clean sharp sand complete all specified and directed.

S&F steel ventilators with top hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel complete all as specified and directed, complete all as specified and directed

S&F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed

S&F 4mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed

S&F aluminum, anodized, barrel tower bolts of extruded section 200 mm long, complete all as specified and directed by Engineer-in-charge..

S&F aluminium alloy, anodised, sliding door bolt 250 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy,complete all as specified and directed by Engineer-in-charge.

S&F brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed

S&F 15mm bore galvanised mild steel tubes `medium grade' galvanised with all fitting & fixed complete to walls & ceilings or laid in floors of complete all as specified and directed

S&F 20mm bore galvanised mild steel tubes `medium grade' galvanised with all fitting & fixed complete to walls & ceilings or laid in floors of complete all as specified and directed

S&F bib taps 15 mm bore, cast copper alloy chromium plated with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule fancy type complete all as specified and directed

S&F angle valve 15 mm bore cast copper alloy, chromium plated fancy type, with long shank & cup , cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed

S&F Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed

S&F ball valve 20mm bore high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed (Make : Prayag/Polytuff or equivalent)

S&F pillar taps 15 mm bore, cast copper alloy chromium plated with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed

S&F brass chromium plated WHB mixer for mixing Hot & Cold water high pressure, screwed down for 15 mm bore iron pipe complete all as specified and directed. Make:- Jaquar/Marc/Cera as approved by GE

S&F chromium plated two way bib cock with wall flange single lever screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified and directed. Make- Jaquar Cat No: ORM-10041 or equivalent in Marc/Cera as approved by GE

S&F Hand shower (Health faucet) Cast copper alloy chromium plated with 8mm dia , one metre long flexible tube & wall hook complete screwed for iron pipe bore dia 15mm complete all as specified and directed. Make :Jaquar Allied Series ALD-572 or equivalent in Marc/Cera as approved by GE

S&F vitreous China wash hand basin oval type, including cutting for and pinning in end of brackets,32 mm waste fittings,brass chromium plated for glazed ware sinks,basins etc.with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed.and flush pipe of polytethylene of low or high density or PVC 32 mm dia incl waste pipe complete all as specified and directed

S&F in repairs vitreous China squatting pan “ORISSA” pattern size 580mm X 440mm, white with P or S trap front or back inlet with integral foot rest (excl flushing cistern & flush pipe) & including PCC bedding, connection to trap & to flushing pipe anti syphonage pipe etc complete including making good to floor complete all as specified and directed by Engineer in charge.

S&F vitreous China urinals, half stall type (flat back), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, three layered wall construction, ISI marked embosed, hoisted and fixed in position including connecting up pipes complete all as specified.

S&F PVC connections 15 mm size and 450mm long/Brass/ PTMT nuts complete all as specified and directed

S&F Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays. Including bolts & nuts & securing ends of stays to wall or roof for 100 mm bore pipe, complete all as specified and directed.

M&L for PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement, complete all as specified and directed.

M&L for hardcore of Broken stone/boulders gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface complete all as specified and directed

M&L for 15 mm thick cement plaster in CM 1:4 on even surface of brick wall mixed with 3% WPC finished even and smooth without using extra cement, complete all as specified and as directed. (Note:- Water proofing compound shall be measured and paid separately under respective items).

Supply only integral water proofing compound complete all as specified and directed

M&L for rendering 5 mm thick cement plaster in CM 1:3 on concrete surfaces as in ceiling finished even and smooth (without using extra cement) complete all as specified and directed

M & L for prepration of newly plastered wall sufaces & applying Birla / J. K. wall care white putty 2 mm thick for levelling the surfaces & applying two coats exterior emulsion weather proof paint over one coat of exterior wall primer incl. of walls complete all as specified and directed . Make Asian ACE or equivalent as approved by GE

M & L for prepration of newly plastered wall surfaces & applying Birla / J. K. wall care white putty 2 mm thick for levelling the surfaces of walls and applying two coat of distemper oil emulsion over a coat of wall primer incl. preparation of surfaces of walls etc complete all as specified & directed.

M &L for applying three coats of white wash on newly plastered ceiling surfaces including preparation of these surfaces complete all as specified & directed.

M&L for rounding to the edge of stone slabs one edge such as in steps, cooking plateform and other similar situations complete all as specified &directed.

M&L for 100 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregates) as in sub base of floors complete all as specified and directed

S&F 150 mm dia Reinforced concrete pipes, Class NP2, laid and jointed complete with collars all as specified and directed

M&L for concrete bed to drain pipes of 150 mm dia using PCC 1:4:8 type D-1 (using 20 mm graded stone aggregate) including packing under, and haunching against the sides of pipes after they are laid and tested in, complete all as specified and directed.

M&L for cement concrete 1:3:6, type C-1 using 20mm graded stone aggregate as in drains, coping, benching in man holes or similar work etc, complete all as specified and directed.

M&L for precast cement concrete, 1:2:4, type B1 (using 20mm graded stone aggregates) cover slabs and lintels etc, complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregates) as in surface channels and drains complete all as specified and directed.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped end etc complete all as specified and directed.

Add or deduct for each 25 mm girth or part thereof over or under 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped end etc complete all as specified and directed.

Cutting existing GI tubing for alterations ,screwing existing tube size of 40 mm and 50 mm dia for new connection including earth work and clamp, neccessory fitting as per site required.

Taking down copper/aluminium point wiring (light fan, socket or power) complete including fittings such as switch, sockets, c/rose, lamp holders, tube light fittings, sketch fitting , wooden boards, bell push, call bell, MCBs & regulators etc & making good to disturbed surfaces & matching with the existing colour of wall floor etc.

Taking down main switch, DB of any capacity complete all as specified and directed.

M&L for concealed point wiring for one light point controlled by one switch with 1.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable in & incl PVC conduit, , including of junction and terminal boxes, all fittings such as tees, bends, elbows, etc. of External diameter 20mm all as per site requirements including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and PVC laminated hylem/Anchor ISI marked top cover 3.0 mm thick for mounting of switches/sockets/ regulator etc and PVC insulated & unsheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead complete all as specified and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green Make– Havells/Polycab/Finolex

All as per Srl item No.168 above but for one 5Amp independent socket point controlled by one switch

All as per Srl item No.168 above but for one 3 pin, 5 Amp socket point with other switch on the same board

All as per Srl item No 168 here in before but for power point wiring using with 2.5 sqmm FRLS PVC insulated , unsheathed, copper conductor stranded 1100 volt grade cable and 2.5 sqmm PVC insulated ,unsheathed, copper conductor stranded 1100 volt grade cable as continuous earth lead complete all as specified and colour coding of cables such as Phase-Red, Neutral-Black and Earth-Green.

S&F switch piano flush type, single pole, one way, 5 Amp 230 Volt complete all as specified and directed. Make-Plaza octa series /L&T/Havells Reo

S&F socket outlet , 5 pin, 5 Amp flush, 230 Volt complete all as specified and directed. Make-Plaza octa series/Anchor /Havells Reo

S&F ceiling rose, surface backlit, 63.5x48 mm three terminal complete all as specified and directed. Make-Plaza octa series /L&T/Havells Reo

S&F lamp holder insulated with back plate with 9 watt LED bulb suitable for Angle/Batten fitting complete all as specified and directed. Make-Plaza octa series /L&T/Havells Reo

S&F switch piano type flush, single pole, one way,15 Amp 230 Volt complete all as specified and directed . Make-Plaza octa series/Havells Reo/Anchor

S&F socket outlet 2 in 1, 6 pin, 5/15 Amp ,flush type universal shuttered 230 Volt complete all as specified and directed Make-Plaza octa series/Havells Reo/Anchor

M&L LED TL 18 watt fitting for surface mounted lumanaires batten with extrued LM 79 & LM 80 certified (certificate to be enclosed) aluminium housing and robust long life corresion resistance impact proof surface mounting IP66 Lumanires PC housing in opeal finish coverwith high brightness complete all as specified and directed. . Make Havells LED 6000K 4 (feet) or eqvt in Philips/CG

S&F testing and commissioning of MCB SP 6-40 Amp 240 Volt 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed. Make - Legrand/L&T/Havells

All as per Srl item No.179 above but SPN 32- 63 Amps, 240 V. Make- Legrand/L&T/Havells

S&F sheet metal enclosure for DB double door, IP-43 when MCBs to be used SPN, 4 way, 240 V with 200 Amps rated bus bar incl TW board of suitable size complete all as specified and directed. . Make- Legrand/L&T/Havells

S&F exhaust fan 250 MM sweep PVC body incl Lovers complete incl making holes in any construction complete all as specified and directed.

S&F exhaust fan 300 MM sweep PVC body incl Lovers complete incl making holes in any construction complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core complete all as specified and directed.

M&L for bricks of old size as in cable protection covers complete all as specified and directed

M&L for clean, dry sand filled in trenches/ducts for cushioning of cables complete all as specified.Note :- The depth of cushion after punning shall only be measured.

M&L for GI tubing of size 25 mm bore, medium grade, ISI marked complete all as specified and directed .

S&F sheet metal enclosure for DB double door, IP-43 when MCBs to be used SPN, 8 way, 240 V with 200 Amps rated bus bar incl TW board of suitable size complete all as specified and directed. Make- Legrand/ L&T/Havells

S&F electronic double space rotary step type 5 speed regulator 120- 280 V complete all as specified and directed. Make- Plaza octa series/Havells

Taking down and refixing connecting ceiling fan with painting all as specified and directed by Engr-in-Charge

S&F box type LED fitting 1x9 Watt 2 feet box type complete .Make:Havellls /Wipro/CG ll as specified and directed by Engr -in -Charge

S&F LED 20 watt fitting for surface mounted lumanaires batten with extrued PVC housing and robust long life corresion resistance impact proof surface mounting IP66 Lumanires PC housing in opeal finish coverwith high brightness complete all as specified and directed. Make - Havells cat part no LHEXBXPNIN1W020/PhIlips/Wipro/Bajaj

M&L for concealed sub main wiring with 2 single core PVC insulated, unsheathed copper conductor stranded 1100 volt grade cable of size 6 sqmm (FRLS) drawn in and incl PVC rigid conduit medium grade of size not less than 20 mm dia ISI marked ivory white with all accessories such as tee, bend, joint cover etc PVC insulated, unsheathed copper conductor stranded 1100 volt grade cable of size 6 sqmm (FRLS) cable as continuous earth lead complete all as specified and colour coding of cables such as Phase-Red, Neutral-Black and Earth-Green

M&L electric water heater (Geyser) ISI marked 25 Ltrs capacity AC 230V, 5 star rating Branded heavy duty automatic cutoff and including electric connection lead of suitable size and length and all accessories, grouting of nut bolt/fastner on wall and making good disturbed surface complete all as specified and directed. Make - Racold/Usha/Havells

S&F LED Building security Light fixture with IP-66 protected die-cast aluminium housing with high power LED as lighting source and lens embedded PC cover having . Maximum power consumption shall not exceed 60W and optics shall be properly designed with Polycarbonate Lenses to avoid dark patches on the road. Street light without lenses will not be acceptable. Driver shall be 3 stage "Constant Current Constant Voltage" with voltage range of 150-270V AC. Output voltage of driver should be complied to Safety Extra Low Voltage norms not exceeding 60 V DC. Note: (i) The item rate shall deem to include provision of weather proof PVC insulated aluminium conductor cable 2.5 Sqmm, 2 core as required. Make of LED light fitting : Havells Cat part No ENDURAPEARLPLUSSL60W LED757SASYTOPC (60 Watt LED) or eqvt in Wipro/Philips

M&L for provn of earthing complete with galvanised steel earth plate electrode, 600x600x6mm buried directly in ground (Earth pit not less than 2.25M deep below the GL) with top edge not less than 1.5 metres below ground level connected with galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts & washers of GI or steel all as shown in electric plate No 3 of SSR-2009 connected to earthing test point all as specified or indicated including testing on completion.Note :- (i) The rate quoted shall also deemed to include the cost of GI wire and protection pipe upto 7.5 Mtr beyond the earth plates electrode and also the cost of the Test point. (ii) Joining of GI earth wire with pipe of the test point shall be done by using suitable cable lugs.

M K Construction

dipangashu barick and associates