PROVN OF TOILET AND ALIIED INFRA, PROVN OF TOILET NEAR OLD MAP BLDG NO P-19, PROVN OF 06 NOS AC AND ALLIED WKS FOR SPL STORES ACCN AT ROWRIAH, ADDN/ALTN OF TOILET BLOCK AT BLDG NO P-32 AT SARAIBARI, PROVN LIGHT CONDUCTOR IN P-33 AND, SPL REPAIR TO B

Amount

NOTES :The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc. or for shafts, wells, cess pits, manholes, pier holes etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out as in soft/loose soil.

Excavation in trenches not exceeding 1.50 m wide and exceeding 1.50 m and not exceeding 3.0 m in depth for foundations or for shafts, wells, cesspits, manholes, pier holes etc. not exceeding 10 Sqm on plan and not exceeding 1.50 m in depth and getting out in soft/loose soil.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level n. exc. 1.50 m above the starting point.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil.

Earth filling under floors, spreading and levelling in layers not exceeding 25 cm thick and well ramming including watering as required.

Material and labour for Plain Cement Concrete M-7.5(Nominal Mix) using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

Material and labour for Plain Cement Concrete M-10(Nominal Mix) using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

Plain Cement Concrete M-15(Nominal Mix) using 12.5 mm graded stone aggregate as in making good window opening, lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping, kneelers, apex stones, bed plates, kerbs, water trough and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

Material and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in foundation & plinth beams complete all as specified and directed.

Material and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in beams and Lintel Beam complete all as specified and directed.

Material and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in column complete all as specified and directed.

Material and labour for Reinforced Cement Concrete M-25 (Design mix) using 20 mm graded stone aggregate as in slabs supported on walls, beams and Columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material and labour for Precast Reinforced Cement Concete cover slab type M-20 (Nominal mix) using 20 mm graded stone aggregate, set in Cement Mortar (1:4) complete all as specified and directed.

Use and waste of formwork for foundations, foundation beams etc. for rough finished surfaces of concrete complete all as specified and directed.

Use and waste of formwork to sides of columns complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves for flat surfaces complete all as specified and directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10 cm but not exceeding 20 cm wide for rough finished surfaces of concrete.

Use and waste of formwork to soffits of suspended slabs such as roof slab, floor slabs, landings not exceeding 200 mm thick (horizontal or sloping) for rough finished surfaces of concrete.

Material and labour for TMT Bars Fe 500D 10mm dia & over cut to length bent to shape required inculding cranking bending spirally hooping for columns etc and binding with MS wire ennealed less than 0.9mm dia or securing with clip complete all as specified and directed.

Material and labour for TMT Bars Fe 500D 6mm dia & 8 mm dia cut to length bent to shape required inculding cranking bending spirally hooping for columns etc and binding with MS wire ennealed less than 0.9mm dia or securing with clip complete all as specified and directed.

Material and labour fo TMT bars Fe 500D of 6 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel (annealed) wire not less than 0.90 mm dia

Dismantling plain/corrugated steel sheeting, any guage, thickness including eves gutter / rain water pipe complete & removal all as specified

Dismantling steel work including gates, rafter, purlin, roof truss etc complete all as specified & as directed.

Material and labour for Rolled mild steel in roof truss (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including cleats Fe-410 W (Gde E-250) Quality-B including one shop coat of zinc chromate primer after preparation of surface complete all as specified and as directed.

Supply and fixing of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Supply and fixing of pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.

Material, labour and fixed of aluminium snap grid frame work for false ceiling, size of grid 605 x 605 mm, including aluminium main/closs tee of size 35mm x 23mm x 1.5 mm ( minimum) aluminum TEES section and aluminium angle of 25mm X 25mm X 1.5mm thick, sutiable type GI wire hanging arrangement with adjuster all as specified in clause no 10.38 in SSR part-I and including 4mm thick high pressure steam cured non asbestos fibre cement designer board as per IS 14862 with applying of two coats of acrylic distemper over a coat of primer complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards / slabs / blankets, any thickness, including cover fillets, etc complete all as specified and as directed.

Demolition of brick masonry built in cement sand mortar including all quoins, arches, pillars , etc complete all as specified and as directed.

Cutting holes in brick walls exceeding half brick but not exceeding one brick built in cement mortar for inserting hold fasts of GI pipe and making good dismantled portion in cement concrete 1:2:4 type B1 exceeding one brick.

Material and labour for Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Material and labour for brick work with bricks class designation 75, size as per old size brick, straight or curved on plan exceeding 6 m mean radius half brick thick walls built in Cement Mortar 1:4 complete all as specified and as directed.

Rendering 15 mm in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment. Note:- Water proofing compound shall be measure and paid separately

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth with using extra cement, with water proofing treatment.

Material and labour for Rendering 5mm thick plaster in Cement Mortar (1:3) on fair faces of concrete surface on ceiling and finished even and smooth with using extra cement, with water proofing treatment.

Supply only integral liquid water proofing compound complete all as specified and directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Material and labour for Preparation of new plaster wall surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.

Material and labour for complete removal of existing finishing of internal wall surface of building/structure by mechanical appliance and preparation of old surfaces and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.

Material and labour for complete removal of existing finishing of internal wall surface of building/structure by mechanical appliance and preparation of old surfaces and applying two coats of two coats plastic emulsion paint of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.

Material and labour for Preparation of new surface and applying 3 coats white wash on walls complete all as specified and as directed.

Material and labour for preparation of new surfaces and and applying 2 coats of cement based paint over a coat of alkali based primer complete all as specified and directed.

Material and labour for complete removal of existing finishing of internal wall surface of building/structure by mechanical appliance and applying 2 coats of cement based paint over a coat of alkali based primer of any description over 10 cm girth or width complete all as specified and directed.

Material and labour for preparation of old external wall surfaces and applying a coats of cement base paint complete all as specified and directed.

Demolition of cement concrete ( un-reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing debris to a distance n.exc. 50 m etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the MOD premises complete all as specified and as directed.

Material and labour for 75 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in plinth protection laid in alternate panel , finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 75mm thick plain cement concrete 7.5 (Nominal Mix) using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

Material and labour for 25mm thick plain cement concrete 15 (Nominal Mix) using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

Material and labour for Hard core of gauge not exceeding 63 mm of broken stone or boulders , spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface

Material and labour for 75 mm thick plain cement concrete M-15(Nominal Mix) using 20 mm graded stone aggregate as in bed of flooring complete all as specified and as directed.

Material and labour for Sand filling under floors or in fdns incl watering and consolidation

Material and labour for Plain Cement Concrete M-15(Nominal Mix) using 20 mm gaded stone aggregate as in Surface channel and drain

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.11Sqm and not exceeding 0.18Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old/new concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Material & Labour Non skid ceramic tiles(digital type), coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.18Sqm and not exceeding 0.36Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Material & Labour Glazed ceramic tiles 450x300/ 300x200 x7 mm(Coloured) on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete over 10mm thick screed bed vertical layer in CM (1:4)all as specified and as directed.

Material & Labour Material and labour for outdoor, antiskid, vitrified paving tiles, of size 300mmx300mmx10mm laid in floors, set and jointed in cement mixed with pigment to match tile colour over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Material , Labour and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed..

Materials and labour for mild steel of grade• Fe-290 Gde-E-165 as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. exceeding 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified and as directed.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. not exceeding 1.50 Sqm each complete all as specified and as directed.

Supply and fixing of pressed steel door frames (fabricated out of CRLCS sheet 1.6 mm thickness) 125 x 60 mm size with one or more rebates including necessary fixing lugs, hinges, lock striking plate etc. complete all as specified and as directed.

Supply and fixing of 30 mm thick flush shutters, solid core construction, with block board core and comercial plywood face panels with one face is covered with decorative face veneer with lipping/frame to match all complete all as specified and as directed.

Material and labour for 35 mm thick, second class hard wood, factory made glazed and skeleton shutters, open rebated and prepared to receive gauze, etc. with plain chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Material and labour for Solid PVC door frame of size 50mm x 47 mm made out of 5 mm wood grain printed PVC sheet reinforced with Mild Steel square tube, suppling & fixing in opening as per drawing complete all as specified and directed.

Material and labour for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawingcomplete all as specified and directed.

Materials and labour for Mild Steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290(Gde E-165) complete all as specified and as directedincluding taking dwon old one complete all as specified and as directed.

Supply and fixing of steel ventilator with top hung shutters including hinges with steel handle and steel peg stay complete without gauged bars, dovetailed or welded complete all as specified and as directed

Supply and fixing of Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Supply and fixing of powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

Supply and fixing of powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

Supply and fixing of sheet glass 4 mm thick ordinary quality fixed to aluminum door & window in squares in each pane of required size complete all as specified and as directed.

Supply and fixing of Glazing with sheet glass (frosted on one side) 4 mm thick ordinary quality with oil putty in square not exceeding 0.5 Sqm in each pane.

Supply and fixing of Butt hinges Stainless steel 100 mm size complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 150 mm complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 200 mm complete all as specified and directed.

Supply and fixing of Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long .complete all as specified and as directed.

Material and labour for Aluminium handles cast type anodised 125 mm size complete all as specified and directed.

Material and labour for Stainless steel wire cloth, 0.43 mm nominal dia of wire and avergae width of aperture 1.00 mm and fixed with stainless steel wire staples complete all as specified and directed.

Material and labour for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed..

Material and labour for Painting 2 coats of synthetic enamel paint on wooden surfaces of any description over 10 cm in width or girth including preparation new surface and one coat of pink primer complete all as specified and as directed.

Taking down old GI tubes of 15 mm bore on wall surface etc all as specified and as directed

Taking down old GI tubes of 20 mm bore on wall surface etc all as specified and as directed

Supply and fixing of 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed.

Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed.

Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and laid in trenches complete all as specified and as directed.

Supply and fixing of 25mm bore galvanised steel tubes, medium grade with all fitting and laid in trenches complete all as specified and as directed.

Supply and fixing of Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore

Supply and fixing of Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 25mm bore

Supply and fixing of in repair 15 mm bore chromium plated stop valve ( concealed type ) with crutch handle ,fancy type , screwed both ends for iron pipes etc complete all as specified and directed. Make :- Cat no 272210120211(DHAARA) of Somany or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of 15 mm bore chromium plated stop valve ( concealed type ) with crutch handle ,fancy type , screwed both ends for iron pipes etc complete all as specified and directed. Make :- Cat no 272210120211(DHAARA) of Somany or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of 15 mm bore chromium plated stop valve with crutch handle ,fancy type , screwed both ends for iron pipes etc complete all as specified and directed.

Supply and fixing of 15mm bore angle valve type cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe for union 15mm complete all as specified and directed. Make :- Cat no 272210120061(DHAARA) of Somany or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of bib cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no 272210120031(DHAARA) of Somany or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repair of bib cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no 272210120031(DHAARA) of Somany or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of chromium plated pillar cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no 272210120011(DHAARA) of Somany or equivalent model of make list as given in PS as approved by GE.

Supply and fixing in repair of chromium plated pillar cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no 272210120011(DHAARA) of Somany or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of vitreous china wash basin white flat back, size 550 x 400 mm including CP waste coupling,with GI pipe brackets & , rag bolt in cement concrete/brick wall and including taking down existing HWB and making good wall surface complete all as specified and as directed.

Supply and fixing of vitreous wash hand basin oval type 550 mm x400 mm (min) fixed to counter including CP waste coupling,with GI pipe brackets & , rag bolt in cement concrete/brick wall and including taking down existing HWB and making good wall surface complete all as specified and as directed.

Supply and fixing of Vitreous china wash down water closet (pedestal pattern) with concealed S-trap or P-Trap, white, 390 mm high, seat cover including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc and including taking down existing one complete all as specified and as directed

Supply and fixing as in repair of PVC low level flusing cistern 10 litres capacity white with ball valve & brackets with flush pipe complete all as specified and as directed.

Supply and fixing of Vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white with including CI ‘P’ or ‘S’ trap & integral foot rests fixed in cement concrete and including taking down existing one complete all as specified and as directed

Supply and fixing of Vitreous China half stall urinals, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, magnum urinal spreader, pointing around urinal back in cement; flush pipe, grating and Union for discharge pipe and including taking down existing one complete all as specified and as directed

Supply and fixing of Vitreous china bowl urinal flat back, size of 465x355x265mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe with and including Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

Supply and fixing of PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

Material and labour for Soap dish chrome plated complete all as specified and as directe

Supply and fixing of chromium plated brass glass shelf fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified.

Supply and fixing of Towel Rail 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

Supply and fixing in repair of Towel Rail 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

Supply and fixing of 125 mm dia of shower rose with 225 mm long arms, cast copper alloy chromium plated , swivel joints and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified.

Supply and fixing in repair of 125 mm dia of shower rose with 225 mm long arms, cast copper alloy chromium plated , swivel joints and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified.

Supplying, hoisted and fixed in position of rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 500 litres capacity with ISI marked and all as specified in IS 12701 complete all as specified and directed .

Supplying, hoisted and fixed in position of rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 1000 litres capacity with ISI marked and all as specified in IS 12701 complete all as specified and directed .

Supply and fixing of uPVC of type-B for use in soil and waste discharge systems, single socket, 110 mm bore in any length including rubber ring joints and fixed to walls with clips and other standard material and all as specified in IS 13592 complete all as specified and directed.

All as per item no 115 above but 75mm bore complete all as specified and directed.

All as per item no 115above but 50mm bore complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )bend for 110 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )bend for 75 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )juction equal or unequal for 110 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of PVC(SWR) vent cowl, 110 mm bore

Supply and fixing PVC (SWR) floor trap 75 mm, plain with CP grating including joining and solvent cement complete all as specified and directed.

Supply and fixing of 50 mm dia low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm fixed complete to walls, ceiling or in floors etc including cutting, chasing, pinning and making floor good with existing one all as directed

Supply and fixing as in repair of health faucet of ABS body with wall hook and including one metre long stainless steel braided rubber hose pipe fixed on 15 nn dia angle cock all complete complete all as specified and directed

Supply and fixing of Toilet paper holder chrome plated complete all as specified and directed.

Supply and fixing of Soap dish chrome plated complete all as specified and directed.

Material and labour for Brick work with class designation 75 bricks, old size bricks in one brick thick honey comb walling built in Cement Mortar 1:3 complete all as specified and directed.

Material and labour for Loose filling with aggregates of gauge 20 mm complete all as specified and directed.

Supply, laying and testing of 150mm internal diameter of double wall corrugated(DWC) high density polyethylene pipes (HDPE) and stiffness classes-8 (SN-8) with ISI marked(with CML no) with and including all fitting & jointing material for sewage line and laid in trenches as specified in IS-16098-2013 part-2 complete all as specified and as directed_

Material and labour for cement concrete (1:3:6) type C2 (using 40mm graded stone aggregate) as in concrete bed to drain pipes 150 mm bore, including packing under and hunching against the sides of pipes after they are laid and tested complete all as specified and as directed. Note:- Thickness of PCC bed 10 cm and width of PCC bed shall be outer dia of pipe plus 30 cm.

Supplying & fixing of toilet cubicle(Crazy Balls Type) of made of 12mm thick drake colour solid compact with decorative thermosetting synthetic resin bonded laminated panels as per confirming of IS 2046 suitable for toilet purpose with resistance of heat, bacteria, , chemical, scratch, impact ,anti bacterial resistant, water absorption and including all building hardware such as SS Door Knob, SS Gravity hinges, SS thumb turn lockset indicators, SS Coat Hooks cum door stopper, SS U Channels, SS Adjustable Foot, SS Screws & wall Plugs, aluminum Powder Coated Top Rail, Noise deafening Tape etc including all necessary accessories as per manufacture instructions complete all as specified and as directed . The size of cubicle compartment as under:- (i)Toilet cubicle compartment size of 1300 mm(L) x 992mm(W) x 1500mm(H):- 05 nos (ii)Jenitor closet cubicle compartment size of 1300 mm(L) x 992mm(W) x 1500m(H):- 03 nos (iii) Urinal Paration 550 mm x 1200 mm:- 01 No Door size of 600mm(W) x 1200m(H):- one per compartment (iv) As per existing room layout drawing Make :- Model :-Crazy Balls of GREENLAM INDUSTRIES LIMITED or equivalent material of Century Plyboards (India) Ltd /Archidply Industries Ltd.

Subtotal of Sch A part-I

SCHEDULE 'A' PART - II FOR E/M PORTION (Sl No __ to ____)

Taking down carefully unserviceable copper / aluminium point wiring (light, fan, bell socket or power) including all fittings such as switches, socket, ceiling roses , regulators and switch boxes etc complete and making good the disturbed surfaces complete all as specified and as directed.

Material and labour for point wiring with PVC insulated unsheated stranded copper conductor cable of size 1.5 sq mm in and including PVC cassing caping of required width with all necessary fittings with sunk cast iron /pressed steel terminal box of1.6mm wall thickness and 3 mm thick laminated sheet top cover for mounting switches including 1.5 sq mm PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly for one light / ceiling fan/exhaust fan/bell controlled by one switch complete all as specified and directed .

Supply and fixing of switch piano flush single pole one way 5 amps complete all as specified and as directed.

Material and labour for point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for one light/fan point controlled by one switch complete all as specified and as directed. Note:-Flush steel terminal box, inner plate and front plates shall be measured and paid seperately.

Material and labour for Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for modular one socket outlet 5 pin 6 amps on independent board complete all as specified and as directed.

Material and labour for Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSH copper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly for one 5 amps socket outlet on same board with other switch complete all as specified and as directed.

Materials and Labour for Point wiring with 2.50 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 4.00 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for modular one socket outlet 5 pin 16 amps on independent board complete all as specified and as directed.

Materials and Labour for Point wiring with4.00 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 4.00 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for modular one socket outlet 5 pin 16 amps on independent board complete all as specified and as directed. NOTES FOR ITEM NO 141to 145- Flush steel terminal box, inner plate and front plates shall be measured and paid seperately.

Material and labour for Metal flush box 2 module complete all as specified and as directed.

Material and labour for Metal flush box 3 module complete all as specified and as directed.

Material and labour for Metal flush box 4 module complete all as specified and as directed.

Material and labour for Metal flush box 6 module complete all as specified and as directed.

Material and labour for Metal flush box 8 module complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) ,2 module complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) ,3 module complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) , 4 module complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) , 6 module complete all as specified and as directed.

Material and labour for White cover plate with frame (both ineer plate & outer plate cover) , 8 module complete all as specified and as directed.

Material and labour for Modular switch 6 Amp single pole one way complete all as specified and as directed.

Material and labour for Modular switch 16 Amp single pole one way complete all as specified and as directed.

Material and labour for Modular socket 16/6 Amp 3 pin combined shattered complete all as specified and as directed.

Material and labour for Modular socket 6 Amp 2/3 pin combined shattered complete all as specified and as directed.

Material and labour for Electronic type fan regulator step type 120 watt, 230 volt complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65x50mm three terminals complete all as specified and as directed.

Supply and fixing of 4 module MCB protected power unit for Air conditioner with MCB double pole 16-25 Amp, Starter Unit 16-25 Amp and socket 16-25 Amp with plug top complete all as specified and directed

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

Supply and fixing of LED surface/ceiling mounting(suspended from ceiling) box type light fitting 20Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with 120 Lumen per watt (Minimum) and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. mm copper conductor flexible wire/cable complete all as specified. Make : Model No CCS-100-20-65-HL2-DP-NWH of Crompton/ BCLAB 20W WH LED P of Bajaj or equivalent model of make list as given in PS as approved by GE.

Supply & Fixing of LED street light fitting ( Building Security light) of 35Watt with LED lamp’s & driver and made of pressure die-cast aluminum housing, IP 65/IP 66 road way luminaries with UV stabilized polycarbonate cover or toughen glass cover & high power LED’s as light source with 110 Lumen per watt and electronic driver with efficiency > 85% . The light fitting shall be fixed on wall/pole with and including 25 mm dia( or higher size as per manufacturers recommendation) light grade GI pipe (bend to shape or as per manufacturers recommendation ) bracket 1.5 mtr long complete with MS flat iron clamp (clamps shall be 40 x 5 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primer and including taking up old light fitting complete all as specified and as directed Make:- Model No- TRP-400-35-57-SL-LM-NSR of Crompton Greave/ NXT P 36L WH CR PC SD of Bajaj or equivalent model of make list as given in PS. Notes : GI pipe bracket and clamps shall be deem to be included above quoted rate..

Supply and Fixing exhust fan 240V, 300mm sweep, 900 RPM , MS body, highly efficient heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings and conforming to IS: 2312 and including aluminium lowers and shutters fixed to wall , writing the MES fan numbers with paint and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed.

Supply & Fixing exhaust fan 250mm sweep PVC body with louvers symphony type, AC single phase,including electrical connection with twisted three core PVC insulated flexible cord of size 0.75sqmm copper conductor from celing rose complete all as specified and as directed.

Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 8 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length complete all as specified and as directed.

Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 4 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length complete all as specified and as directed.

Supply and fixing of MCB SP of rating 6 to 32 Amps 240 V complete all as specified and as directed.

Supply and fixing MCB DP 40 to 63 amps 415 volts 10KA breaking capacity complete all as specified and as directed.

Material and labour for Sand cushioning to the full width of trenches for protection of cables including punning down complete all as specified and as directed. Note :- Thickness of sand cushioning shall be the thickness after punning down.

Material and labour for laying of Class designation 75 bricks, old size, flat, common clay laid in trenches across the trench as cable protection complete all as specified and as directed.

Material and labour for laying of LT XLPE insulated armoured heavy duty cable 1100 volt grade ISI marked with alumimium conductor multi strand cross sectional area 50 Sqmm x 3 ½ Core complete all as specified and as directed.

Material and labour for laying of LT XLPE insulated armoured heavy duty cable 1100 volt grade ISI marked with alumimium conductor multi strand cross sectional area 16 Sqmm x 4 Core complete all as specified and as directed.

Material and labour for laying of LT XLPE insulated armoured heavy duty cable 1100 volt grade ISI marked with alumimium conductor multi strand cross sectional area 10 Sqmm x 4 Core complete all as specified and as directed.

Material and labour for laying of 40mm bore galvanised steel tubes, light grade for cable protection complete all as specified and as directed.

Material and labour for air termination ,single point copper rod 12 mm dia and 300 mm long fixed on the roof including all fitting complete all as specified and directed.

Material and labour for test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm, drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed.

Material and labour for Earth continuity conductor or main earthing lead, aluminkum, 25 x 3 mm size, fixed to wall with epoxy earthing strip insulator of size 25mm x3 mm fixing on wall for earthing continuity conductor or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required complete all as specified and directed.

Material & Labour for Plain Cement Concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in coping, pedastal of pole and necessary form work complete complete all as specified and directed .

Material & Labour for earthing with galvanised steel earth plate electrode of size 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts check nuts and washers of galvanised iron using GI 4 mm dia wire as earthing lead as shown in electrical plate No. 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:3:6 type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe, 40mm dia GI medium grade earth lead protection pipe, CI frame and cover, wire, copper lugs etc mesh, chorcoal and common salt in alternatee layer complete all as specified and directed .

Material & Labour for earthing with galvanised steel earth plate electrode of size 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts check nuts and washers of galvanised iron or steel using GI strip 25x4mm as earthing lead as shown in electrical plate No. 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:3:6 type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe, 40mm dia GI medium grade earth lead protection pipe, CI frame and cover, wire, copper lugs etc mesh, chorcoal and common salt in alternatee layer and including taking down existing one complete all as specified and directed .

Supply, Installation, testing & Commissioning of hi wall split type Air conditioners of cooling and heating function of capacity 2.0 ton , 3 Star Rating(minimum) of BEE, comprising of indoor/outdoor complete with cordless remote control unit, one compressor and filter and including suitable size copper refrigerant piping with 13mm thick nitrile rubber insulation, electrical interconnection copper cable between indoor and outdoor units, PVC drain pipe complete all as specified and as directed. NOTE :- (i) The quoted rate shall be deemed to lifting, shifting, positioning at site of all the equipment, fittings, topping up of refrigerant, outdoor control panel, bracket / clamp for indoor/outdoor units installation, vibration isolators, and ancillary material as per manufacturer’s instruction. (ii) The above quoted rate shall be deemed to included of Refrigerant piping upto 3.0 m, copper conductor cable upto 3.0 m, remote controller and drain pipe upto 3.0 m Make:- Carrier/Daikin/Hitachi/Bluestar/ Voltas/ Godrej/ Samsung / LLOYED

Supply and fixing voltage stabilizer for automatic operation, single phase with neutral, air cooled indoor type and designed for input voltage variation between 130 volt to 250 volt with output voltage stabilized at 230 volt with accuracy of +/- 2.5% and capacity of 4 KVA complete all as specified.

Supply, design, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminum bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING :-

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

MS J B CONSTRUCTION AND CO

M/S M R CONSTRUCTION & CO