PROVN OF TEMPORARY STORE SHED AT FOD UNDER GE (S) PATHANKOT

Amount

Surface dressing n exc 15 cm deep, complete all as specified and directed.

Excavation in tranches in n.exc 1.5m wide and n.exc 1.5m in depth for foundations etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in hard/dense soil, complete all as specified and directed.

M&L PCC (1:4:8) type D-2 (using 40mm graded aggregate) in foundation, filling, mass concrete. complete all as specified and directed.

M&L for Brick work with subclass ‘B’ bricks,straight or curved on plan exc 6m mean radius, built in CM 1:6, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm, complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting, complete all as specified and directed.

M&L for RCC 1:2:4 nominal mix for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete 20 mm graded agg., complete all as specified and directed.

M&L for RCC 1:2:4 nominal mix for Columns,pillers, posts and struts 20 mm graded agg., complete all as specified and directed.

M&L for RCC 1:2:4 nominal mix for beams Beams, cantilevers, bressummers,lintels over 1.5m span using 20 mm graded agg., complete all as specified and directed.

M&L for Moorum/red bajri/local soil filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering, complete all as specified and directed.

M&L for Hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface, complete all as specified and directed.

M&L for Cement concrete type C- 2, 1:3:6 (20mm graded aggregate) sub base 100 mm thick, complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, rafters rails and fastenings and heavy bracket framing (beem, tee, angle, channel or flat sections) including distance pieces, cleats etc of FE 410 W (Gde E-250) quality B including one shop coat of red oxide primer complete all as specified and directed.

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or othercovering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (including of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete .

M&L for Preparing the new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint all as specified.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws. Sheet colour approved by Engineer-in-Charge complete all as specified and directed.

M&L for pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws. Sheet colour approved by Engineer-in-Charge complete all as specified and directed.

S&F in position suspended false ceiling system using E-grid suspended ceiling grid system. The size of grid shall be 600 x 600mm with GI frame work main runner 38 x 24mm cross tee 25 x 24mm and wall angle 24x24mm, using 8-9mm thick ceiling panel laminated with PVC film on front face and foil back availabel in due drop texture as per IS-2095, part-I-1996, fixid in the grid of E-grid suspended ceiling grid system duly suspended by 4mm dia GI bar hanger from the purlins of the roof with butter fly clips .

Providing, cement concrete 1:3:6 (20 mm graded aggregate type C1) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs and inside pressed steel door frame as directed

S&F Galvanised mild steel wire cloth 0.56mm of nominal dia of each wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples.

S&F steel window/ventilator with tubular frame factory made double shutters of size 79mm x 39mm, 14 gauge rectangular tubular frame with side hung shutter glazed and gauged with glazing bars 12x3mm flat iron incl projecting type hinges with steel handles and steel peg stay dovetailed or welded incl necessary locking arrangement, complete all as specified and directed. (wire gauge, grill and glass shall be measured and paid separately.)

S&F Mild steel framed work such as grills, gratings using square/round bar with ends of bars shoulders/welded drilling holes for fixing of guard bars all as specified.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc. 0.50 Sqm in each pane. complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc, rough finished, complete all as specified and directed.

M&L for Flat Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beam and similar work; vertical or to for fair finish, complete all as specified and directed.

M&L for Flat Formwork to sides of pillars, posts, struts, piers, columns and stanchions with rough finish. complete all as specified and directed.

M&L for rendering 15 mm thick in cm 1:4 on fair faces of block masonry /brick work surfaces finished even and smooth without using extra cement. complete all as specified and directed.

M&L for two coats of cement base paint over a coat of primer on newly plastered surface of wall including preparation of surface and curing after applying each coat complete all as specified and directed.

M&L for rendering 10 mm thick in cm 1:4 on fair faces of block masonry /brick work surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips Fe-410-W (Gde.E-250) Part- I quality-A or Fe 290 (Gde E-165) .

M&L for Mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips Fe-410-W (Gde.E-250) Part- I quality-A or Fe 290 (Gde E-165) .

M&L Preparation of new surfaces and applying two coat Of OBD over a coat of white wash on walls, complete all as specified and directed.

M&L for Cement concrete type B-0, 1:2:4 (12.50 mm graded aggregate) as in floor 40 mm thick, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for glass dividing strips,3 mm thick 38 mm width and inserted in position, conform to design 38 mm wide, complete all as specified and directed.

M&L 75mm thick plain cement concret type C-2 1:3:6 (using 20mm graded crushed stone aggregate) as in flooring/Sub base/Plinth protection all as spd and directed.

Surface exacavation n exc 30 cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified and directed.

Supply only sand filling under floors, complete all as specified and directed.

M&L for Machine pressed precast concrete inter locking paver block any shape with grey cement and pigment size conforming to IS 15658-2006 of 60mm thickness,M-35 Grade laid over sand cushioning. Note :- sand shall be measured and paid separetly.

S&F for LED light fitting 2x16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size.

M&L for flame proof point wiring with 1.5 Sqm 1100 volts grade PVC insulated FRLS copper conductor single core multi strand flexible cable with proper colour codig in and including ERW rigid steel conduit & fitting (ISI marked) and acessories including flame proof bends, couplers, junction boxes etc fixed on wall /ceilling with proper fixing arrangements incl proper conductor 1.5 Sq mm PVC insulated unseathed multi stranded FRLS copper conductor single core cable (green colour) as earth lead continuity conductor fixed to earth terminal and metallic body of light fittings complete all as suitable for two independent light point controlled by one way switch

S&F explosion proof/ flame proof rotary switch with termination box in LM6, 16A, double pole 250V

Distribuiton board eclouser 8 way made out of galvanised steel sheet Class EX II housed with MCBs for the follwing capacity (i) MCB SPN 10 KA breaking capacity 32 Amps -01 Nos (ii) MCB SPN 10 KA breaking capacity 6 Amps - 06 Nos Note : The encloser and MCB's should be flame proof with explosion protection suitable for Zone - II. The rate quote quoted by the tender shall be deemed inclusive of all accessories required for the connections.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 04 sq mm 2 core

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1,5 mtrs in depth for laying of cables including getting out in any type of soil complete all as specified and directed.

Returning filling in including spreading, leveling ,and well ramming, in layers not exceeding 25 cm each layer of any type of soil.

Removing surplus excavated material (soil) from site not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point.

M&L for sand cushioning for cables 8 cm below the cable and 15 cm above the cable all as specified and directed .

M&L for old size brick well burnt, laid flat ,for cable protection complete all as specified and directed.

S&F air termination single pointed aluminium rod 12mm dia and 300 mm long for fixing on GI pipe medium grade 40mm dia pipe duly making suitable fixing arrangement of one end of air termination rod all as specified and directed by engr-in-charge. Note: GI pipe required will measured and paid separately.

S&F Aluminium strip 25 x 3 mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete with saddles and insulators made out of porcelain and fixing screws for roof conductor/ down conductor including nut bolts& washers drilling and riveting for joints of suitable size as required at site all as specified and directed by Engr -in- Charge. Note :- Porcelain insulators are to be fixed at an interval of not more than 75 cm

M&L for Test point termination block made of gun metal or phosphorus bronze of size 75mmx75mmx25mm drilled and screwed including 3 Nos 8mm dia & 25mm long hexagonal head screw complete all as specified and as directed.

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated location for loop earthing etc. with GI strip 32x6mm.

M&L for plain Cement concrete 1:2:4 type B-1, (Using 20 mm graded aggregate) as in foundation block for fixing GI pipe for installation of air termination rod etc. complete all as specified Note:- Unit rates includes for provn of form work for rough finished surfaces and finishing the exposed surfaces with 5 mm thick rendering in CM 1:3 all specified.

S&F GI pipe medium grade 40 mm dia for fixing Aluminium strip 25x3.15 mm on roof for lightening protection duly drilling 2 Nos holes on Aluminum strip and GI pipe on one end and fixing with screws/suitable size of bolts & nuts complete all as specified. Note: GI Strip required will measured and paid separately.

M&L for earthing with steel earth plate electrode of size 60x60cmx6mm thick buried directly in ground to a depth not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr deep below normal ground level connected to galvanized iron strip of size 32x6mm as earthing lead by means of nuts, bolts and washers of GI and GI strip protected by provision of GI medium grade pipe 40mm bore, 20mm dia GI medium grade watering pipe with funnel and wire mesh, RCC pit cover of size 300x300x40mm reinforced with XPM having weight not less than 4Kg/sqmm including 6mm thick MS bar handle made to shape, PCC pit with 1:3:6 type C1 with angle iron frame made of angle iron of size 40x40x4mm, adequate qty of charcoal dust and salt layers all around the earth plate, excavation , earth work in any type of soil, removal of excavated soil and returning filling in all as required at site complete all as specified in plate No 3 of SSR Part-I and all as specified or indicated including testing on completion.NOTE :-Rates inclusive of necessary excavation in any type of soil, earth work, PCC pit, RCC cover, funnel with watering pipe, GI earth strip upto 7.5 m long for connecting to test point etc. all as required at site for complete earthing).

Note: In case the tenderer quotes different rates for similar item then lowest rate shall only be applicable for payment and contractor shall not have any claim on this account.

V K Sharma and Sons

BUILDEX CONSTRUCTION CO

OMKAR SHARMA AND CO

M/S BISHAN DASS AND SONS

VIJAY KUMAR LAKHNI