COMPREHENSIVE B/R MAINT MISC WKS AT MIL STN UDAIPUR

Amount

Taking down chowkats or frames area not exceeding 1.50 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed. (Note – The quoted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid).

Taking down chowkats or frames area exceeding 1.50 Sqm and not exceeding 4.00 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed. (Note – The qouted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid).

Taking down shutters of any description not exceeding 1.00 Sqm each, from chowkhat complete all as specified.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each, from chowkhat complete all as specified.

Supply and fixing for mild steel framed work as in door chowkats/gate of angle or angle iron work as in fixing of cooler stand by drilling/cutting the stone masonry wall and fixing up to 1st floor walls, other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides), complete all as specified and as directed by the Engr-in-Charge.

Material & labour for PCC 1:2:4 type B-1 ( using 20mm graded mechanically crushed stone aggregate) as in bed blocks, copings, apex stones,side of interlocking tiles, embedding to cooler stands in wall, embedding hold fasts etc complete all as specified and directed.

Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 65 mm x 125 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company.

Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 45 mm x 70 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company.

Supply and fixing for 2nd class hard wood 35mm thick Plain, framed, panelled shutters (06 number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete. (Make : A-1 Teakwood, Cat No : A1T-MD2 or equivalent)

Supply and fixing IInd class (hollock) hard wood factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed. (Make : A-1 Teakwood, Cat No : A1T-GD5 or equivalent)

Material and labour for two coat of synthetic enamel painting to new wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer complete all as specified and directed.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N / m2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fie retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engr-in-Charge. (Note : Stainless steel butt hinges and necessary SS screws shall be paid separately).

Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply & fixed 150 mm long Extruded aluminium alloy handles, fabricated type anodised complete all as specified.

Supply & fixed 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed.

Supply and fixing 100 mm long stainless steel butt hinges with galvanised MS hinge pin etc.

Supply and fixing alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified.

Supply and fixing double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber all as specified and directed by Engr-in-charge.

Supply & fixed in repairs MS helical door spring 150 mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats.

Supply & fixed steel windows box type ERW hollow 'P' section comprising double frame including gauged and glazed skelton shutter 30mm thick jointed internally with flat iron 25x3mm complete including hinges handle tower bolts, stops lugs,grill etc all as shown in drawing CEJZ TD -20 sheet 1/3 to 3/3 as applicable complete Note :- For the purpose of measurement & payment double shutter with frame and grill shall be considered as one unit. (ii) Glazing,wire mesh & painting shall be measured & paid separately.

Supply and fixing factory made steel window with side hung shutter including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded including two coat of enamel paint over one coat of primer.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames, glazed with putty or fixed with beads.

Supply and fixing for 3.0 mm thick sheet glass, ordinary quality and glazing with oil putty in square not excc 0.5 Sqm in each pane complete all as specified and as directed by the EIC.

Supply and fixing wire netting of stainless steel wire1.4mm dia (size of mesh 12mm) fixed with tinned tacks of stainless steel wire staples or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified.

Supply and fixing (in repairs) wire netting of stainless steel wire1.4mm dia (size of mesh 12mm) fixed with tinned tacks of stainless steel wire staples or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified.

Material and labour for anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified Note minimum thickness of powder coating 50 micron.

Supply & fixed for anodised aluminium grill of (anodised transparent or dyed to required shade according to IS:1868 with minomum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with C.P. brass / stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised alumiinium standard section around the opening, all complete as per reuirement and direction of Engineer encharge.

Material and labour for 4mm thick figured glass, ordinary quality and glazing rubber beading in square nexc 0.5 sqm in each pane complete

Material and labour for 5.5mm thick plain sheet glass, ordinary quality and glazing rubber beading in square exc 0.5 sqm in each pane complete

Supply & fixed in repairs aluminium (die cast) body door closer hydraulically regulated designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed, ISI marked all as specified and directed.

Supply & fixed in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, ISI marked all as specified and directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings any gauge, thickness complete all as specified as directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified as directed.

Supply and fixing pre-painted galvalume aluminium zinc coating (AZ-150) GI based corrugated steel sheet 0.50 mm thick of any colour having 550 Mpa tensile strength as in roof covering/cladding and fixed with self tapping screws, complete all as specified.

Supply and fixing pre-painted galvalume aluminium zinc coating (AZ-150) GI based plain steel sheet 0.50 mm thick of any colour having 550 Mpa tensile strength as in roof covering/cladding and fixed with self tapping screws, complete all as specified.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified as directed.

Material and labour for suspended false ceiling system using Chicago Metallic (E-grid) exposed suspended system, grid size 600mm x 600mm comprising of GI poweder coated main dunner fo dimensions 39mm x 24mm xx 0.8mm thick (thickness comprising of GI/0.4mm +PPPCGS/0.3mm & weight of runner 1.35 Kg for 3600mm length), cross tee of dimensions 29mm x 24mm x 0.8mm thick (thickness comprising of GI/0.4mm + PPPCGS/0.3mm & weight of Tee 0.195 Kg for 600mm length) and wall angle of dimensions 22.2mm x 22.2mm x 0.65mm thick (thickness comprising of GI / 0.35mm + PPPCGS/.3mm & weight of angle 0.70Kg for 3050mm length) with and including 4mm thick HPSC (High pressure steam cured) pre-primed, self embossed, tentured designed board to be placed in the grid system duly suspended with 4mm dia GI wire hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt-0.007 kg/clip), hold down clips (wt-0.0035 kg/clip), with provn of light fixture complete all as per manufacturer's instructions and as directed.

Material & labour for fabrication of pressed steel cupboard shutter using 1mm thick MS plain sheet with frame 1.25mm thick bent to shape including two coat of synthetic enamel paint on internal surfaces & two coat of hammer tone finish on external surface alongwith locking arrangement mortice lock ,handle etc complete all as specified as per drg No CEJZ/TD/12/2008 sheet 1/3 to 3/3.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site ofm work as directed by the Engr-in-Charge.

Material and Labour for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base/mass concrete and finished the top surface even and fair complete all as specified.

Material and Labour for Vitrified out door tiles 40 cm x 40 cm x 10-12 mm thick digital design set, jointed and pointed in neat cement slurry as in floors with grey cement over & including over screed bed or bedding layer of mortar 20 mm thick Cement Mortar 1:6. (Make-H & R Johnson, Brand-Endura digital designer series or eqv)

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

Supply and fixing for erection and fixing of Stel work in tubular trusses including special shaped washer etc, complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240, complete all as specified and as directed.

Material and Labour for two coats of synthetic enamel paint on new steel surfaces over a coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding/rendering complete all as specified and directed.

Material and Labour for Non-skid jointless Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.

Material and Labour for Vitrified digital double charge tiles 10 mm thick ( square or rectangular) polished, area of each tiles not exc. 0.36 sqm, in floors etc. set and jointed with Balendura adhesive or equivalent as approved by Engr-in-Charge and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer with CM 1:4 all as spd and directed.

Material and Labour for Vitrified digital double charge tiles 10 mm thick of size 600 x 100 mm on polished on vertical faces of walls set and jointed with Balendura adhesive or equivalent as approved by Engr-in-Charge and pointed in white or coloured cement to match over and including 10mm thick rough finished plaster in cement mortar (1:4) all as spd and directed.

Material and Labour for Glazed ceramic coloured tiles in vertical surfaces 600x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified & directed.

Material and Labour for granite 18-20mm thick (of any type) work (table rubbed and polished) in steps, pillars, window cills, cooking platforms including half round moulding as reqd, making hole for gas pipe etc. and like in cement mortar (1:4) incl pointing in grey cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick CM 1:6 screed bed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified.

Material and labour for reinforced cement concrete Type B-1, 1:2:4 (using 20mm graded aggregate) Nominal Mix as in beams, cantilevers, bressummers, lintels over 1.5m span canopies, deck slabs and in shelves and the like, complete all as specified and as directed.

Material and labour for reinforced cement concrete Type B-1, 1:2:4 (using 20mm graded aggregate) Nominal Mix as in chajjas canopies, deck slabs and in shelves and the like, complete all as specified and as directed.

Material and labour for formwork to sides and soffits of floor or roof beams,lintels, cantilevers etc. and similar work, comlete all as specified and as directed.

Material and labour for formwork to chullah hoods, chajjas, troughs and similar items including edges, comlete all as specified and as directed.

Supply and fixing for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and as directed.

Ditto- but 6mm to 8mm dia (as in stirrups).

Demolition of brickwork or stone/boulder masanory,laid dry below or above ground level and removing material from site complete all as specified and directed.

Material & Labour brick work with old size fly ash bricks straight or curved on plan exc. 6 M mean radius built in CM 1:6, complete all as specified and as directed.

Material & Labour for Brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and as directed.

Material & Labour for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6, compelte all as specified and as directed.

All as per item above but except stones, complete all as specified and as directed.

Taking down cement plaster from brick walls ,concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.

Material and labour for Rendering 15mm thick on fair faces of concrete block masonry/brick masonry in cement concrete 1:4 cement mortar and finished fair and smooth all as specified.

Material and labour for Rendering 15mm thick on stone masonry surfaces in cement concrete 1:4 cement mortar and finished fair and smooth all as specified.

Material and Labour for 15mm thick rendering on fair faces of brick work/stone masonry, concrete surfaces (external walls) or stone walls upto tripple storey bldgs in cement mortar 1:4 mixed with liquid water proofing compound using as per manufacturer’s instructions, finished even and fair, complete all as specified. Note : (i) WPC shall be measured and paid separately. (ii) Rendering upto 9 mtr ht shall be included in the quoted rate).

Material and Labour for Preparation of old surfaces of walls, pillars cornices surfaces including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, removing nails making good holes cracks etc on plastered or unplastered surfaces and applying one coat of white wash on walls complete all as specified and directed.

Material and Labour for Preparation of old surfaces of ceiling including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts removing nails making good holes cracks etc on plastered or unplastered surfaces and applying one coat of white wash on ceiling complete all as specified and directed.

Material and Labour for applying one coat of oil bound distemper on walls, pillars cornices etc surface incl preparation of old plastered surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and incl filling necessary where required with putty as in patches or nail holes obtain smooth finish using sand paper and matching the existing surface complete all as specified and directed.

Material and Labour for subsequent coat of distemper oil emulsion ( White/ Ivory or any colour) over one coat applied under Srl item No 126 above.

Material and Labour for applying 1 mm thick weather coat Asian/Birla/JK wall care white putty in two layers including complete removal of existing treatment of internal or exxternal walls, roof projection, fins and fascia etc. with wire brush or any manual other mechanical method by manual and reaching upto old plastered surface complete all as specified and directed.

Material and Labour one coat of exterior emulsion paint white or tinted on old treated walls or fascia of roof or chajjas on prepared putty surfaces of bldg upto tripple storeys bldgs complete all as specified & directed. Note : Make :-Asian Paints (Brand-Ace)/ Berger paint (Brand -Walmasta) / Nerolac paint (Suraksha plus)

Material and Labour for one coat of exterior emulsion paint white or tinted on walls or fascia of roof or chajjas width between 10 cm to 20 cm on prepared putty surfaces or old painted surfaces of bldg upto tripple storeys bldgs including filling necessary where required with putty as in patches or nail holes obtain smooth finish using sand paper and matching the existing surface complete all as specified & directed. Note : Make :-Asian Paints (Brand-Ace)/ Berger paint (Brand -Walmasta) / Nerolac paint (Suraksha plus)

Supply & fixed Polymer coloured (Polypropeylene Delrin and ABS) low level flushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS derscription mark with 2731 with and including suitable size of MS brackets, plug, screws all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed. Make : Jaquar/Cera/Hindware/Parryware

Supply & fixed in repair vitreous china wash hand basin flat back white of size 550mmx400mm with 32 mm dia chromium plated waste coupling including flush pipe etc complete all as specified. Make : Jaquar/Cera/Hindware/ Parryware

Supply and fixing in repairs, vitreous China squatting pan of Orrisa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified. Make : Jaquar/Cera/Hindware/ Parryware

Supply and fixing in repairs vitreous china premium quality/1st quality wash down water closet pan (pedestal pattern), white (excluding flushing cistern & flush pipe) & incl 01 No ‘P’ or ‘S’ trap of dia 100mm including provn of lime concrete bedding, complete all as specified. Make : Jaquar/Cera/Hindware/ Parryware

Supply and fixing in repairs,15mm bore pillar tap, fancy type, chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks , compete all as specified.

Supply and fixing in repair, bib tap screwed down high pressure, cast copper alloy,fancy type, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified.

Supply and fixing in repair white colour rotational molded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 500 Ltr hoisted and fixed in position after dismantling (water tank of cap exc 250 ltr and n.exc 500 ltr) and removing to store and all as specified and directed by Engr-in-charge.

Supply and fixing in repair white colour rotational molded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position after dismantling (water tank of cap exc 250 ltr and n.exc 500 ltr) and removing to store and all as specified and directed by Engr-in-charge.

Supply and fixing in repair PTMT ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes all as specified and directed by Engr-in-charge.

Taking up or down 15mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the entire satisfaction of Engineer-in-charge.

All as per item above but 20mm dia bore, complete all as specified and as directed by the EIC.

Supply and fixing (in repair) stop valves, 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified.

Supply and fixing (in repair) angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified.

Supply & fixed in repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified.

Supply & fixed in repairs stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified.

Supply & fixed in repair fancy type shower rose125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint complete all as specified.

Supply & Fixing in repair chromium plated mixer for wash hand basin for mixing hot and cold water screwed down for iron pipes suitable for 15mm bore pipe complete all as specified and directed by Engr-in-charge.

Supply & Fixing in repair Brass CP bath Mixer 3 in 1 System with provision for overhead and hand shower suitable 15mm bore of pipe and fixed.

Demolition and breaking up of CI/AC rain water pipe /UPVC pipe line 100mm/75mm dia incl all fittings, complete all as specified.

Supply & Fixed for 110mm dia UPVC, soil waste drain pipe, type ‘A’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches or in floors, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be conforming to IS 5382-1985)

Supply & Fixed for 110mm dia UPVC, soil waste drain pipe, type ‘A’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint fixed to wall, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be conforming to IS 5382-1985)

Supply & Fixed for 75 mm dia UPVC, soil waste drain pipe, type ‘A’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint fixed to wall or floor complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be conforming to IS 5382-1985)

Supply & Fixed for 110 mm bore UPVC (SWR) bend with access door including jointing with solvent cement, complete all as specified. .(Note- UPVC bends shall be conforming to BS 4515 DIN 19531 and DIN 19534)

Supply & Fixed 110 mm bore UPVC (SWR) ( singleT) equal or unequal, branch piece,single ( singleY) equal or unequal including jointing with solvent cement, complete all as specified.

Supply & Fixed for 75 mm bore UPVC (SWR) bend including jointing with solvent cement, complete all as specified. .(Note- UPVC bends shall be conforming to BS 4515 DIN 19531 and DIN 19534)

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames and Supply and fixing for 3.0 mm thick sheet glass, ordinary quality and glazing with oil putty in square not excc 0.5 Sqm in each pane upto 12 mtr height of building complete all as specified and as directed by the EIC.

Supply and fixing repair of Rain Water Pipe of dia 110 mm (4") PVC pipe fixing done with Pipe Support Clamping System upto Two Storey building consists of Rain Water Bracket Set with Pipe Support Channel + U Bolt Rubber Sleeve mounted system running vertically with wall distance 75 mm (3") : Pipe Support Clamping made of : 1. Rain Water Bracket Set with pipe support channel for 110 mm (4") PVC pipe having Wall Distance 75 mm (3") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32 mm width x 3 mm thickness with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs. 2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Quantity for one unit : 1. Rain Water Bracket Set for 110 mm (4") PVC dia. pipe with pipe support channel; Wall distance 75 mm (3") - 1 Nos. ; 2. U Bolt rubber sleeve mounted for 110 mm (4") PVC Pipe Dia. - 1 No.; and 3. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jodhpur Zone Technical Drawing of Factory Made Pipe Supporting System : CEJZ/TD/102. Make: Shaivi or equivalent as approved by AGE(I).

M/s Ajay kumar Garge

M/s SUNIL ENTERPRISES

naveen enterprises