Construction of Thirumana Mandapam

Amount

Earthwork excavation for foundation in all soils and sub soils to full depth as may be directed except in hard rock requiring blasting inclusive of shoring shuttering, baling out water wherever necessary, refilling the foundation with excavated earth and depositing the surplus earth within compound in places shown by the departmental officers with an initial lead of 10 metre and initial lift of 2 metre and clearing and leveling the site etc., complete complying with standard specification and as directed by the departmental officers. SS20 B.

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification and as directed by the departmental officers.

Refilling with excavated earth other than crushed stone sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and FILLING GRAVEL Supplying and filling in 'foundation and basement with filling crushed stone sand in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.and as directed by the departmental officers.

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.30 M height with all cross bracing for plane surfaces as detailed below using mild steel sheets of 90X60 cm 10 gauge stiffened with MS angle of 25 X25X3 mm for boarding,laid over adjustable span & jacks and supported by 50 mm dia pipes for general pipe scaffolding system @ a spacing of 1.20 m c/c and vertical connected at a height of 20 m c/c and vertical connected at a height of 2.0 m c/c including 'c'&'U' clamps and base receiver cup at bottom for connecting pipes etc and removable system etc.,the rate including cost of all materials,labour Charges, wastages, placing , transportation,lead & lifts,tools & plants, fuels,fixing in position at all levels ,height,masking tape in sheet joints,consumables ,etc.as complete with all respects complying with relevant standard specification,as directed by the Engineer-in-charge.

For column footing,plinth/grade beam,bed blocks,template surface,steps,piers,raft slab/beams and such other members

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For plane surfaces such as For circular columns

Extra for additional height in centering,shyttering wherever required with adequate bracing propping etc. including cost of de-shuttering and decentering at all levels.over a height of 3.30m(height shall be the dimensions as measured from the top of the lower slab /pcc sub base to the bottom of the subsequent upper slab) for every additional height of 1m or part thereof fpr plan area to be measured suspended floors,nat slabs,drops post tensioned slabs,slabs curved in plan to any radius,grid slab,rools landings beams including spiral and curved beams of all radius,post tensioned beams,gnd beams,plinth beams,griders bressumers.cantilevers and balconies.rate to include all materials,labour charges,wastages placing,transportations,lead & lifts,tools & plants,fuels,fixing in positions at all levels,masking tape in sheet joints,consumables etc.as complete with all respects complying with relevent standard specification,as directed by the Engineer-in-charge.

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

a)For foundation and basement

b) Ground floor

b) First floor

Terrace Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in Cement Mortar1:5 (One cement,five sand) using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

For foundation and basement

Brick work in Cement Mortar1:6 (One cement,six sand) using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Ground Floor

First floor

Terrace Floor

Brick partition walls of 11.50cm thickness using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Ground Floor

First floor

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Paving the floor with best quality double charged Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with following ceramic tiles of size joint free rectified ceramic tile of size 305 x 305 x 8 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality, white / colour glazed tiles of size 450X300mmX8 set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.(Dadooing ceramic tiles of size 300mm x 450mm x8mm)

Paving the floor with best approved quality natural flammed finish granite for flooring /steps &landing of 18/20mm thick of with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3(one cement and three crushed stone sand)fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with matching colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the executive engineer concerned before use on work ,etc.,complete as per standard specification.kota stone slab of size 600 x 600 of 18 / 20mm (un-polished) in all floors laid in of cement mortor 1:3 (one cement three crushed stone sand), 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification and as directed by the departmental officers.

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete complying with as per standard speicification and as directed by the departmental officers.

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.and as directed by the departmental officers.

Supplying and fixing mild steel grills for windows, ventilators, etc., including priming coat etc., complete complying with standard specification.and as directed by the departmental officers.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete complying with standard specifications.and as directedd by the departmental officers.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. (The window should be got approved from the Executive Engineer before use on work)

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Solid PVC Door Shutters toilet door using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter

Supplying ,fabricatting and fixing in position of Alumi Anod.using 5.5 mm thick frosted glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading ,AI.Clips,best track arrangement on top,Alumin if necessary chipping,dismantling making necessary holes in RCC columns,beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete.The Alumi.surface must be anodised with mattfinish under electrically controlled condition in accordance with IS specification 1868/1962 of Anodic filthickness of not less than 15 Microns(fifteen) for all sections.All the materials should be got approved by the engineer-in charge before fixing as directed

Door frame:supplying and fixing first quality teak wood frames for doors,windows,ventilators and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc.complete in all floors.etc.complete complying with standard specification and as directed by the departmental officers.

Teak wood scantings up to 2M

Teak wood scantings over 2M and below 3M

Supply & fixing of single leaf solid core flush shutters with teak ply on both side with teak wook lipping alround 35 mm thick ,with necessary adhesives and cp screws complying with standard specification.The cost is inclusive of 1No lock arrangement,handle,tower bolt,approved equivalent make SS ball bearing hinges of quivalent make of approved make ,2 no floor mounted SS door stoper ect.complete as per drawing.

Supply & fixing double leaf solid core flush shutters with teak ply on both side with teak wood lipping alround 35 mm thick,with necessary adhesives and cp screws complying with standard specification.The cost is inclusive of 1No lock arrangement,handle,tower bolt,approved equivalent make SS ball bearing hinges of quivalent make of approved make ,2 no floor mounted SS door stoper etc.complete as per drawing. make:kutty,s haron,trojan . Accesserorice Make:dorma,godrej.

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Toilet sunken using broken brick jelly 20 mm gauge the proportion of broken brick jelly to slaked lime being 1:3:6(1part cement,3part fine aggregate & 6part broken brick jelly),well beaten by wooden beaters for giving required slope and thickness required etc complete complying with standard specifications and as directed by departmental officers.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting two coats with approved water based emulsion paint over the cement plastered wall surface ceiling other new surface including clearing preparing the surface covering all floors including brushes etc.complete and as per standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with weather proof ready mixed exterior emulsion paint of first class quality and of approved colour over a priming coat including through scrapping,clean removal of dirt,and including necessary plaster of paris putty,wherever required etc., complete complying with standard specification.

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Paving the Top of roof with Solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush.Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier.The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed.Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Providing Vargapoochu over the corewalls of Vimanams / Gopurams, with Cement Mortar1:4 complete including shaping the mukhapathram, mahanasi, Koodu all ornamentals works to proper shape by embedding broken bricks of shaped/chiseled bricks, rough-plastering with Cement Mortar1:4and finishing with final ornamental plastering and nayam theervani including cost and conveyance of all materials, labour therefore, lifting of materials, all working in heights, curing with water etc, complete including all extra for folding and including clearing from the vimanams/gopurams 100sft superficial area. for kalkaram

Providing ,supply,mixing laying cement plastering 20 mm thick with cement mortar1:4 mixed with water proofing compound conplast X4211C conforming to IS:2645,@ 150ml per bag of cement (normal setting integral water proofing compound) as specified by the manufacturer over PCC levelling course including preparation of surface,dewatering,finishing,curing etc.all complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position C.I Manhole covers (heavy duty)mof various sizes of best approved quality and as per standard specifications etc., complete 0.6X0.6M size etc., complete

Manhole cover

PVC mould

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15 mm brass connections,15 mm GM wheel valve,15 mm brass nipple (2 NOS.),15 mm nylon connection,TW plugs,screws and also giving necessary connection to the PVC pipe including cost of 600 mm length of 110 mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer,dismantling the masonry and re-doing the dismantled masonry to original condition etc.,complete complying with standard specifications.( The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works)

Supplying and fixing of 15 mm CP two way bib cock with health faucet of parryware or equivalent make conforming to BIS specification and quality including cost of shellac,thread etc., complete complying with standard specification and including cutting and threading whereever necessary.etc.complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware oval type wash hand basin of size 560 x 450mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supply and fixing in position of best Indian make white glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying & fixing of Angle valve stopcock with connecting hose and wall flange(make:parryware or equivalent)

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying & fixing of long bibcock with brackets including fixing over wall tile dado complete.( make parryware or equivalent)

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

40 mm dia

50 mm dia

75 mm dia

110 mm dia

Supplying and fixing position CI Nahani Trap / Floor Trap with best stainless steel gratings/PVC nahini/Floor trap with PVC grating type of size 100X75/75X50mm of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

110 mm dia

Supplying and fixing in position of following dia PVC rain water gratings for rain water pipes of approved quality and variety of various size conforming to ISS and including necessary cutting and fixing and giving connection to PVC pipes etc.,complete complying with standard specification and as directed by the departmental officers .

110 mm dia

Supplying and fixing in position of the following dia PVC specials such as PVC vent cowl etc., of approved quality and variety of various size confirming to ISS amend providing leak proof joint etc.,including necessary cutting and fixing and giving connection to PVC pipes etc., complete complying with standard specification and as directed by the departmental officers.

110 mm dia

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75 mm dia

110 mm dia

160 mm dia

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three crushed stone sandand Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 (one cement,five sand and ten aggregate)of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 4-3/8" x 2-3/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Providing ,supplying & laying of Chlorinated poly vinyl chloride (CPVC-SDR-11)pipes confirming to IS15778 having thermal stability with brass and CPVC fittings like elbow,brass tee ,brass elbow,offsets,toe with [email protected] spacing,with jointing of pipes with one step CPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc.Rate is inclusive of all material labour,transportation,tools&tsckles taxes,etc all complete as per standard s[pecifications ,exposed work including chase cutting,bracket fixing)complete complying with standard specification and as directed by the departmental officer

20 mm dia

25 mm dia

32 mm dia

Providing,Supplying, laying of unplasticized polyvinyl chloride (UPVC-SDR-11)UPVC pipes conforming to IS 15778 having thermal stability cold water with brass and UPVC fittings like Elbow,brass tee,braa elbow,offsets,tee with clamps @ 1.00 meters spacing,with jointing of pipes with one step UPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc.Rate is inclusive of all material labour,transportation,tools&tsckles taxes,etc all complete as per standard s[pecifications ,exposed work including chase cutting,bracket fixing)complete complying with standard specification and as directed by the departmental officer

32 mm dia

40 mm dia

50 mm dia

Providing,Supplying, laying of gunmetal type NRV pressure rating less than 16 kg/sqcm and IS778 with 2 Nos of MTA with jointing material like shellac,thread including testing of the joints complete and making good the walls etc. rate is inclusive of all material labour,transportation,tools & tackles etc all complete as per standard specification ,complete complying with standard specification and as directed by the departmental officers

32 mm dia

40 mm dia

50 mm dia

Supplying and erection of horizontal shaft centrifugal mono block power pump set of single phase 2.00 H.P of best approved quality and make with ISI mark on suitable pedastal with foundation bolt and nut including labour supplying and fixing of starter and main switch suitable for 2.00 H.P pumpset on suitable angle iron frame work witrh necessary labour including panel board,supply and run off 4 of 10 sq.mm in PVC pipe with 14 SWG TC wire including fixing of suction pipe and foot valve up to a maximum depth of 7 m and delivery pipes upto the exterior wall of pump room etc., complete and operating the pumps on trial run for 3 days .( The make and quality of pump set to be got approved by the executive engineer before use on works) ( TWAD-pa.no:103 Sl.no :45)200m X 60 m etc.complete complying with standard specification and as directed by the departmental officers.

Drilling of bore wells in alluvial soil or sedimentary strata of clay and sand or sand stone,shale,pebbles boulders etc., by first taking a pilot bore of 150 mm dia and then enlarging to the required dia by direct or reverse rotary mud circulation method including charges for all T&P , cost of fuel,labour charges,bentonite mud and water required for drilling at the site shown by the departmental officers including construction of mud pit etc., complete

upto 60 m Depth bending below ground level

from 60 m to 90 m depth ending below ground level

Reaming of 150mm dia pilot bore to 300mm dia bore as directed by the departmental officers upto required depth etc.complete

upto 60 m depth ending below ground level

from 60 m to 90 m depth ending below ground level

Supplying and fixing the following size of PVC pipes of approved quality and variety conforming to pressure IS4985.The rate is inclusive of cost of pipe,all taxes,conveyance charges of materials and all other labour charges for fixing the PVC pipe as directed by the departrmental officers etc., complete complying with standard specifications.The PVC pipe should be got approved by the departmental officers before use on work and labour charges for inserting PVC casing pipe assembly ( with slots and without slots) in the drilled holes including jointingnthe pipes with PVC couplers with PVC adhesive etc., complete and supplying and packing annular space with pebbles of size and quality as approved by the departmental officers.

150 mm dia PVC casing pipe ( with or without slot)

Charges for developing borewell with air compressor of 600 CFM capacity (Min 8 Hours) including transportation and labour and fuel charges for the compressor as directed by the departmental officers and conducting yeild test by 'V' notch methoda,excluding cost of bore charges and conveyance charges for handling boring

Supply,errection and giving necessary water supply and electrical connections of new type 2 HP submersible pumpset confirming to IS-14220 with ISI mark suitable for 150 mm borewell ,complete complying with standard specification including suitable 3- phase panel board with DOL with two level guard starter and accessories and labour charges for the erection of submersible pump set in bore well including fixing and jointing the submersible cable ( but excluding cost of 2.50 sqmm-3 core copper cable ) with proper clamps upto other starter to the required depth,valves section clamps,pressure gauges upto the exterior wall of the panel board consisting of JPICN switch starter , voltammeter,ammeter,3 pilot (indicating)lamps,capacitor,single phasing preventor,water level guard and laying and jointing the cables and twin sets on trial run for 3 days etc.,complete complying with standard specifications. with three phase panel board.

Supply and fixing PVC borewell end cap of size 165/168 mm dia etc.,complete complying with standard specifications as directed by departmental officers.

Supply of 4.00 Sq.mm/PVC insulated and sheathed ,3 core flat type copper cable for submersible motor complete complying with standard specifications as directed by departmental officers

Supply and fixing the Nylon rope to connect the submersible motor in borewell etc.,complete complying with standard specification as directed by departmental officers

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe in wall and ceiling with PVC accessories with module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for PVC concealed light / Fan Point (For electronic regulator) (5 Points Per Coil) higher end .

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for PVC concealed light / Fan Point (For electronic regulator) (5 Points Per Coil) higher end

supply and fixing of 18W LED Round type Recessed fitting with LED (Higher end) on false Ceiling from ceiling with PVC unsheathed copper leads from terminals to the fitting(SD530)

supply and fixing of 24W LED 2x2 square type Recessed /surface type fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.(SD 526)

Supply and fixing of 4 feet 20W LED with fitting with LED on wall or ceiling with PVC copper leads from terminals to the fitting(higher end).

Supply and fixing of 4 feet 20W LED with fitting with LED on conduit pipe suspension from the ceiling with PVC unsheathed copper leads from terminals to the fitting(higher end).

Supply and fixing of ceiling fixture 250/300 mm complete with gallery etc.clear glass opac/crystal with 15 W LED bulb

Supply and fixing of 80W LED flood light fitting on ceiling with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing 6 W LED mirror fixing with LED with PVC unsheathed copper leads from terminals to the fitting ( Higher end )

supply and fixing of 30W LED street light fitting with LED (Higher end) with 25 mm dia. GI pipe (class B) with 1 no. 25 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .

supply and fixing of 1200mm (48") sweep AC ceiling fan complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 600mm down rod on the existing fan clamp

supply and fixing of 1400mm (56") sweep AC ceiling fan complete ( Lower end) with 2 module 100W fan step regulator (Lower end) with 600mm down rod on the exisitng fan clamp

supply and fixing of 1200mm (48") sweep AC ceiling fan complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 300 mm (12") sweep (heavy duty) AC exhaust fan complete without provision of hole in the wall

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan

Supply and fixing of 375 mm (15") sweep (heavy duty ) AC exhaust fan complete without provision of hole in the wall

Supply and fixing of louvers shutters arrangements for 375mm (15") sweep light duty AC Exhaust fan complete.

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1no.6A two module socket , 1 no. 6/16A two module socket, 1 no. 6A one module switch, 1 no.16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug)

Supply and fixing of 1 no.16 A one module switch with module cover plate (plastic) on suitable module concealed box (GI) in flush with wall with connections higher end

Supply and fixing of 1 no.16A one module socket with module cover plate (plastic) on suitable module concealed box (GI) in flush with wall with connections.higher end

Supply and fixing of 1500W automatic electric water heater of 35 litres capacity suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flex wire but without plumbing connection

Supply and fixing of 2nos.6/16A two module socket , 2 nos. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and Run of 2 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.

Supply and Run of 2 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.

Supply and Run of 3 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour.

Supply and Run of 3 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.

Supply and Run of 4 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour.

Supply and fixing of 32 A 4P MCB with sheet steel enclosure on wall with earth connection ( higher end )

Supply and fixing of 12 way single pole and neutral RCCB/ELCB 30 MA sheet steel enclosure distribution board with double door (metal) with 1 no. 40 A DP RCB/ELCB 30 A isolator as incoming and 10 nos.6 A to 32 A SP MCB as outgoing in flush with wall with earth connection only .Higher bend

Supply and fixing 4 way single pole and neutral MCB sheet steel enclosure distribution board with double door ( metal) with 1 no.40A DP MCB Isolator as incoming and 4 nos.6A to 32 A SP MCB as outgoing on wall with earth connection only .Higher end

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 8 way vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door ( metal door) with 1.no 63 A 3P MCB,6 nos ,6A to 32 A SP MCB as outgoing with suitable cable end box on wall with earth connection only .Higher end

Supply and fixing of 250 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and fixing of 250 A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply,Erection,testing and commissioning of three compartment LTCT meter box made up of 16 SWG CRCA sheet steel ( length 1200 mm X Height 1200 mm X width 600 mm ) with door and lock & key arrangements on suitable angle iron frame support for floor/wall mounting support with supply and fixing of the following interior mounting arrangements with busbar chamber ,meter chamber and terminal box chamber confirming to IE rules. i.)The bubsar chamber will consist of 4 nos .2"X1/4" tinned copper flat for phase and neutral busbar on epoxy mounted bus insulated at proper and sufficient spacing between the bus bar as per IE rules.ii)3.nos.200/5A CT coil mounted in three phase busbar.iii).interconnection between CT coil to 4 way terminal box and 4 way terminal box to meter box by 4 sq.mm PVC cu.wire.The LTCT meter box should be powder coat paint of approval colour,approved by site officer

Supply,Erection testing and commissioning of 415 V/50 HZ 250A cubic panel board with centre switches chamber the bus bar chamber and cable chamber on extremee end with 16 SWG thick CRCA sheet with 1"X1/4" tinned copper flat for 3 phases and neutral with 6 mm hylem sheet seperation of 3 phases and neutral and with synthetic moulded insulators bus support at equal intervals as per IS specification and 2 runs of 1"X1/8" copper flat on rear side of the panel board for earth buses and digital L & T make digital multifunction meter.with suitable CT coil,with two set of LED pilot lamps set with fuse base ,top & 10 A HRC fuse link for 3 phases on separate chamber and with the following switches complete.(1) 250 A TPN switch with HRC fuses ( L & T/eq)-1.no.(2) 125 A TPN switch with HRC fuses ( L & T /eqq.) -1 no.(3) 63 A TPN switch with HRC fuses ( L&T/eq.)-10 nos.

Supply and Laying of 3 1/2 x 150 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.(SD752)

Supply and clamping of 3.5C x150 sq.mm PVC armoured LTUG cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 150 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 150 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 4X16 sq.mm PVC armoured LTUG cable on post or on wall with MS clamps

Supply and clamping of 4CX16sq.mm PVC LTUG armoured cable in suitable GI pipe on post or on wall with MS clamps ( Data A-18)

Supply and fixing of brass cable gland for 4X16 sq.mm. armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work

Supply and Run of 1 of No.8 SWG copper wire for earth connection

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch,2/4 way connector on suitable hylem sheet and supply and fixing of 3 nos.150 W LED flood light fitting with LED ( higher end) with A1 frame arrangements on post with suitable MS clamps for fixing the fitting and supply and fixing the street light SMC box to house 3 nos 6A SP MCB with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting and supply and fixing of 2 X 48 W LED street light fitting with LED ( higher end ) with 2 nos 1 m32 mm dia GI pipe (class B) complete with suitable MS clamps for LED street light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with paintinjg of suitable colour

Supply ,erection ,testing and commissioning of 62.5 KVA Disel silent generator set 0.8 PF 3 ph,415 V,50 HZ as details below.(A).Engine: Water cooled Disel Engine type suitable for generating application with a shaft output of suitable capacity of 83 BHP at 1500 RPM under NTP conditions.As per BSS 5414/ISO 3046 The Engine shall comprise the following standard fittings.(Kirloskar /Cummins/Equivalent).(B).Alternator:Capacity of 62.5/50 Kw,0.8PF self exited,self regulated design to run a 1500RPM under NTP condition confirming to BS 5000/IS13364(part II)1992 to be coupled directly to the Disel Engine and test certificate.(Kirloskar/stamford/Equivalent).(C).Battery:1 No.12V 88/100 AH Battery with copper leads and terminals,battery make EXIDE/AMCO/AMARON.(I).Acoustic Enclosure :Supply of acoustic Enclosure for 62.5 KVA Disel Generator Set.The Acoustic enclosure is made of 1.6/2 mm thick CRCA sheet in munsel green shade and s Structural Sheet metal base frame painted in black.The walls of the enclosure are insulated with the 75 DBA at mtr sound levels specified by ministry of enforcement.The enclosure should be completed with :(1).Arrangement for power cable for connection.(2).Residential exhaust silencer ,with flexible base arrangements.(3).Suction louvers.(4).Discharge louvers.(5).Openable and lockable doors on both sides with air tight neoprene rubber gasket.(6).Lifting arrangements.(7).Interior lighting arrangements.(J).Erection,testing and commissioning of the genset comprising the following:(1).Providing suitable concrete foundation with plain cement concrete 1:2:4 with sand cushion all around and alternator with acoustic enclosure.(2).Erection of generator set complete with acoustic enclosure,fuel tank,engine control panel,standard control panel,base frame complete on the above foundation and lifting arrangements.(3).First charging of lub oil and first charging of battery

Supply and installation of exhaust pipping of sufficient length with suitable MS pipes so as to extend outside the generator room with necessary thermal insulation

Supply and providing RCC bed concreting for 62.5 KVA DG set

Supply and laying of 3 1/2 x 25 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (SD204)

Supply and laying of 3 1/2 x 25 sq.mm PVC armoured LTUG cable on wall with earth connection (SD222)

Supply and providing cable end termination of 3-1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete(SD235)

Supply and fixing of brass cable gland for 4 x 25 sq.mm. LTUG armoured cable with earth connection(SD185)

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection(SD76)

SUB TOTAL

N. Devaprabhu (BID ID -1099254)