Construction of Primary Health centre Building (Health Instityution Level-II) at Kohbag Tehsil and District Shimla HP.

Amount

Excavation in foundation and trenches in earth work in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the engineer -in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor) as per satisfaction of Engineer- in -charge through all modes of transportation including head load ,animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour ( if required ). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used /removed as per the direction of the Engineer - in- charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respect including all incidental charges.

Excavation in drain and channel in earth work in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the Engineer -in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor) as per satisfaction of Engineer- in -charge through all modes of transportation including head load ,animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour ( if required ). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used /removed as per the direction of the Engineer - in- charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-charge.

Providing form work with steel plates 3.15mm (three point one five millimetre) thick welded with angle iron in frame 30x30x5mm ,so as to give a fair finish including centring ,shuttering ,strutting and propping etc. with wooden \steel battens and ballies , height of propping and centring below supporting floor to ceiling up to all heights and removal of the same for insitu-reinforced concrete & plain concrete work in:complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

In foundation, footings, bases of columns etc. and mass concrete.

In vertical surface such as wall (any thickness) partition and the like including attached pilasters in all floor level in all heights.

In flat surfaces such as soffits of suspended floors, roofs, landings and the like of any thickness in all floor level in all heights.

In columns, pillars, posts and struts. Square, rectangular,circular or polygonal in plan in all floor level in all heights.

In stair cases with sloping or stepped soffits excluding landings in all floor level in all heights.

In beams, cantilevers, girders and lintels sides and soffits of beams, beam hunchings, cantilevers, bressumers and lintels up to any depth in all floor level in all heights.

In edges of slabs and breaks in floors of any width in all floor level in all heights.

Providing and laying cement concrete 1:6:12 (One cement : six sand : twelve crushed stone aggregate 40 mm (Forty millimeter) nominal size) mechanically mixed and vibrated, curing complete excluding cost of form work in foundation and plinth and as per HP. PWD. specifications of 1990 volume-I. including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:4:8 (One cement : four sand : eight crushed stone aggregate 40mm (Forty millimeter) nominal size) mechanically mixed and vibrated, curing complete excluding cost of form work in foundation and plinth and as per HP. PWD. specifications of 1990 volume-I. including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and laying cement concretegrade M-10 1:3:6 (One cement : three sand : six crushed stone aggregate 20mm (Twenty millimeter) nominal size) mechanically mixed and vibrated in retaining / breast walls including curing and cost of form work complete with carriage of materials labour ,tool and plants through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:1.5:3 (one cement isto one point five sand isto three graded stone aggregate 20mm. (Twenty millimeter) nominal size) .mixing the materilas in mechanically mixer and compacting the concrete with vibrater complete excluding cost of form work and reinforcement for reinforced concrete work.and as per HP. PWD. specifications of 1990 volume-I.including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge in

In foundation, footings bases of columns etc. and mass concrete.

In suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto floor all level.

In columns, pillars, posts and struts. Square, rectangular or polygonal in plan, in all floor level in all heights.

Vertical surfaces such as wall (any thickness) partitions and the like including attached pilasters, buttresses, plinth string courses and the like.

Providing and laying upto all floor levels reinforced cement concrete 1:2:4( one cement: two sand: four graded stone aggregate twenty milimetre nominal size) to give smooth and even surface including centring and shuttering but excluding cost of reinforcement ;and curing complete mechanical mixed and vibrated for compacting reinforced concrete as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and laying damp proof course 38 mm thick with cement concrete 1:2:4 (one cement isto two sand isto four graded stone aggregate twelve point five milimetre nominal size) and curing complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Applying a coat of hot bitumen (mexphalt 80/100 or equivalent) using 1.70 kg per square metre on damp proof course after cleaning the surface with a piece of cloth lightly soaked with kerocsene oil. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing tor/TMT steel reinforcement of TATA tiscon / SAIL / Rashtria Ispat /Jindal / Shyam including cost of binding wire for R.C.C.work including bending, binding and placing in position complete in all floor level in all heights,and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying brick work using common burnt clay building bricks in cement mortar 1:6 (One cement : Six sand) with second class bricks in foundation and plinth as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying brick work using second class bricks common burnt clay building bricks in super-structure in all heights,upto all floor levels with cement mortar 1:6 (One cement : six sand)and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying second class half brick masonry in common burnt clay building bricks in all floor levels in all heights with cement mortar 1:4 (One cement : 4 sand) and curing complete including carriage of materials labour ,tool and plants through all modes of transportation as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Constructing Tharry common burnt clay building bricks in super-structure above plinth level upto floor all level using second class building bricks in cement mortar 1:4 (One cement : 4 sand) and curing complete including carriage of materials labour ,tool and plants through all modes of transportation as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Supplying and stacking second class brick bats complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying Random rubble masonry / polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement : six sand : twelve crushed stone aggregate 20mm (Twenty millimeter nominal size) at plinth level in Cement Mortar 1:6 (One cement: six sand) and curing complete including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Stone soling under floor dry hand packed with hard stone of approved quality consolidated properly with hand or mechanical rammer to required level as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Supplying and stacking stone aggregate 40 mm nominal size (forty milimetre) complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing Ist class Kail wood work in frames of false ceiling,partitions etc.,sawn and put up in posion complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing 40x3 mm flat iron hold fast 40 centimetre long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm nominal size) complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 35 mm thrity five milimetre factory made flush door shutter Non-decorative phenol bonded termite resistant and water proof core board 1.00 mtr. high alluminium sheet fixed complete with frame of ISI class hard wood and well match commercial three ply veneer with vertical grain or cross band and face veneer both face of door IS No. 2202 two thousand two hundred two of kit ply/Alpro comtax as per Arch drawing as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing second class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G with wire of dia 0.56mm for doors, windows and clerestory windows including bright finished black enamelled iron butt hinges with necessary screws complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 19 mm (Nineteen milimetre) thick commercial board water proof (ISI mark) shelve/box for cup boards with butt joints & fixing with nails & screws etc. complete. as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge. .

Providing and fixing 19mm ( ninteen milimetre ) thick commercial board water proof (ISI mark) shutter for cup boards including fixing with nickle plated piano hinges with screws etc. complete as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing Ist class deodar wood plain square edged cover fillets(beading) 19mm x 6mm ( nineteen milimetre into six milimetre) section, with wood screws in ceiling and lining including mitring at junctions complete. as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge..

Providing & fixing 125 mm M.S. double acting spring hinges bright finished with necessary screws etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge:-

Providing and fixing anudized aluminium sliding door bolts anodized shade and colour with bolts, nuts and screws etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 250 X 10 mm (two hundred fifty into ten milimetre) size aluminum tower bolts (Barrel type) with screws etc. complete.and as per HP. PWD. specifications of 1990 volume-I.including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing aluminium handles anodized transparent or dyed to required colour or shade with necessary screws etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge:-

Providing & fixing 115 mm bright finished MS hasps and stapples (safety type)with necessary screws complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing 150 mm M.S. single acting spring hinges bright finished with necessary screws etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing brass 100 mm ( One hundred milimeter ) floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per HPPWD specification 1990 volume-I ( One ) including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 300mm oxidized MS hooks and eyes complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing M.S. plain grills of required patterns in wooden frames of windows etc. with M.S.flats, square or round bars with round headed bolts and nuts or by screws complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 12 mm thick and 150 mm wide palmet with 25 mm diametre first class deodar wood curtain rod and brackets including fixing with 25 X 3 mm MS flat 10 cm long & plugs etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Paving and flooring:- Cement concrete flooring 1:2:4 (one cement: two sand: four graded stone aggregate 20mm twenty milimetre nominal size) laid in one layer finished with a floating coat of neat cement as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing automatic hydraulically compressed and polished precast terrazzo tiles ISI marked No.IS: 1237 of approved shade in floor, in white cement 20 mm thick with marble chips of specified size laid in floors,tred of steps and landings on a bed of 25 mm average thickness of cement mortor 1:6 ( 1 cement : 6 sand). jointed with neat cement slurry mixed with pigment to match the shade of tiles ( where ever required) including rubbing and polishing complete with tiles of silver grey shade complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing precast terrazzo tiles ISI hydraulically compressed and polished terrazo tiles ISI marked No.IS: 1237 of approved shade in flooring, in 50% grey and 50% white cement 20 mm thick with marble chips of specified size laid in floors,tred of steps and landings on a bed of 25 mm average thickness of cement mortor 1:6 ( 1 cement : 6 sand). jointed with neat cement slurry mixed with pigment to match the shade of tiles ( where ever required) including rubbing and polishing complete with tiles of silver grey shade complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing precast terrazzo tiles hydraulic compressed 20 mm thick with marble chips of specified size fixed on wall on 10 mm thick cement plaster 1:3 ( 1 cement isto 3 sand). jointed with neat cement slurry mixed with pigment to match the shade of tiles ( where ever required) including rubbing and polishing complete with tiles of silver grey shade complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing coloured/white glazed tiles 300 mm X 450 mm X 8mm thick in skirting risers of steps and dado on 12mm thick cement mortar 1:3 (1cement : 3sand) and jointing with neat cement slurry complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge:-:

Providing and laying 20mm (twenty milimetre) thick White makrana marble work (Table rubble and polished) in flooring 20mm twenty milimetre thick base in cement mortar 1:3 (one cement :three sand ) inculding jointing with cement mortar 1:2 ( one white cement :two marble dust ) with an admixture of pigment to match the shade of the marble. 20mm twenty milimetre thick White makrana marble including rubing and polishing etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying non-slippery spartic ceramic tiles (30 x 30cm/ 40x40 cm) and 10mm thick of NITCO / ORIENT or equivalent in flooring, treads of steps etc. in cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete upto floor all level complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying 25 mm (Twenty five milimetre) thick mirror polished Kota stone slab flooring with 20mm (twenty milimetre ) (average) thick cement mortar 1:4 (one cement is to four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Kota stone slab 25mm thick mirror polished of slab size not less than 550mmx550mm in risers of steps, skirting dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry fixed with pigment to match the shade of the slabs including rubbing and polishing complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 0.60mm thick prepainted steel sheet of TATA Durashine in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia metre with prepainted limpet and rubber washers complete with all accessories as required as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing ridges or hips 60 cm over all thick prepainted steel sheets of TATA DURASHINE in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating+ back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6 mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge.

Providing and fixing valley 60 cm over all 0.60 mm thick prepainted steel sheet of TATA DURASHINE in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia with prepainted G.I. limpet and bitumen whashers complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing flushing 38 cm overall with 0.60 mm thick prepainted steel sheets of TATA DURASHINE in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 30cm wide and 90cm overall semicircular plain GI Sheet for gutter with iron bracket 40x3mm mm (forty into three milimetre) size bolts and nuts and washers etc. including making conection with rain water pipe complete as per design including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing on wall face150mm ( One hundred fifty milimeter ) dia PVC rain water pipes of working pressure not less than 4.5 Kg ( Four decimal five kilogram ) per square meter including filling the joints with approved adhesive complete as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing and fixing on wall face PVC accessories for rain water pipes including filling the joints with approved adhesive complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

150 mm dia PVC plain bend.

150 mm dia PVC shoe.

Providing and fixing M.S. holder bat clamps for approved design to CI or SCI pipes embeded in ansd including cement concrete block 10x10x10 cm (ten into ten into ten centimetre) of 1:2:4 mix ( one cement isto two sand isto four graded stone aggregate 20 mm nominal size and cost of cutting hole and making good the wall etc. complete including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts as per direction of Engineer-in- Charge.

Providing laying steel work of TATA,SAIL or RASHTRIYA ISPAT welded in built up section/ hollow section trusses & framed work, including cutting,hoisting & fixing in position including applying a priming coat of red lead paint in beams joists channels, angles, tee,flats with connecting plates or angle cleats as in main and cross beams, hip and rafters,purlins connected to common rafters and the like as per HP. PWD. Specifications of 1990 vplume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

In gratings, framed, guards, bars ladders and railing, brackets and similar works.

In truss and trused purlins in buildings.

Providing and fixing moulded hand rail of mild steel hollow pipe 50 mm ( fifty milimetre ) dia welded in stright length over mild steel flat at top of vertical balusters woth round ends at two levels at 75 cm 90 cm height in should extend 30 cm beyond the top and bottom of the ramp complete including one coat of red oxide priming coat complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing steel window and ventilators of frame manufactured with mild steel channel section 75x40x5 mm frame and for frame channel section 75x40 mm(seventy five into forty) milimeters with MS flat 75x40 mm to make one frame providing double rebate with making square steel section with mild steel flat of 20x 4mm (twenty into four) milimeters and 12x4mm (twelve into four) milimeters, shutters of Z -section including glass panes of 4mm(three) milimetres thick in glazed panel and wire gauge of designation 85(eight five) G with wire of 0.56mm(zero point five six) milimeters including MS fitting and applying a coat of primer with red lead paint and fixing in position complete as per HP. PWD. Specifications of 1990 Volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing mild steel channel iron door windows frame manufacture from steel iron section of channel 75x40mm in frames of window manufactures of steel section including hingesjambs, lock jambs welded rigidly of fixed by mechanical means lugs with split and tails ti each jambs including steel butt hinges 25 mm thick with the provision for arrangement and sheet or server as specified and applying a coat of primer for perfact wood or the surface complete as per HP. PWD. Specifications of 1990 Volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing MS fan clamp type-I of 16 mm dia MS bar bent to shape with hooked ends in RCC slab during laying including painting the exposed portion of loops complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20 mm X10 mmX2mm and braced with flat iron diagonals 20 mm X5 mm size with top and bottom rails of T.iron 40 mm X40 mm X6 mm with 38 mm dia steel pulley complete with bolts and nuts locking arrangements, stoppers, handles, including applying a priming coat of red lead paint.complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering as required with :complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint other then white brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Applying priming coat over new wood and wood based surfaces with ready mixed paint brushing wood primer pink after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint other than white paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering and stopping.complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Applying priming coat with ready mixed primer over new concrete / masonry / asbestos / cement / plastered surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering as required with :complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

6mm ( six milimetre ) cement plaster to ceiling with cement mortar 1:3 ( One cement : three approved sand ) as per HP.PWD., specification 1990 Volume-I ( one )including carriage of all labourequipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15mm ( fifteen milimetre ) cement plaster in single coat on fair side of brick/ concrete/stone walls of interior plastering upto floor two level including arrises,internal rounded angles, chamfers & rounded angles not exceeding 80mm in ( eighty milimetre ) grith finished even and smooth in cement mortar 1:6 ( One cement : six approved sand) as per HP.PWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

20mm (twenty milimetre) cement plaster with Cement mortar 1:6(one cement :six sand). in single coat on the rough side of brick/ stone/ concrete walls for interior plastering upto floor two level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth as per HP. PWD. Specifications of 1990 Volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

20mm (twenty milimetre) cement plaster with Cement mortar 1:3(one cement :three sand). in single coat on the rough side of brick/ stone/ concrete walls for interior plastering upto floor two level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth as per HP. PWD. Specifications of 1990 Volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

White washing with lime on undecorated wall surfaces two coats to give an even shade including throughly brooming the surface to remove all dirt dust mortar dirt and other foreign matter complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Distempering two coats with oil bound washable distemper of Asian paints or equivalent of approved shade and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer for all floors including entire carriage of materials through all modes of transportation with in all leads and lifts as per PWD specifications and as per direction of Engineer-in-Charge.

Wall painting (two coats) with excluding priming coat on new concrete masonry/ plastered wall surfaces with enamel paint of approved brand and manufacture for use on floors to give an even shade including cleaning of all dirt dust and other foreign matter and sand papering as required complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Finishing wall with weather proof exterior grade emulsion of approved shade and design (Apexultima) or its equarlied on undecorated wall surfaces two coats to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and Laying heavy duty precast cement concrete inter locking paver blocks vibro compacted upto M-50 grade including border or kurb block grey or coloured over sub base of concrete with 25mm thick average thickness of cement mortar 1:4 (one cement isto four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing and polishing complete.(sub base concrete floor to be paid for separetely) incluing carriage of materials within all leadsand lifts and as per the direction of Engineer-in-Charge.

Providing ,laying jointing and painting with stiff mixture of cement mortar in proportion of 1:1 (one cement isto one sand) 150 mm internal diametre salt glazed stone ware grade A half round channel.complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing decorated wall bracket made of 50 mm MS Hollow section20x20 hollow MS section,MS solid squarebar ring including weldingcompleteas per detail including fixing in position complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Applying birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-AL-PE) composite pressure pipe confirming to IS-15450 U.V. stablized with carbon black having thermal stability for hot water suppy including with clamps at 1.00 metre spacing cutting , fixing and making good the wall but excluding the cost of fittings( internal work) pipes concealed in the wall with cutting chases and making good the wall complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

1216 mm (16 mm O.D. pipe)

1620 mm ( 20 mm OD pipe).

Providing and fixing compositeend seal compression fittings as per IS-15450-2004 for cold water supply such as tees , ekbows, reducers,connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Equal Tees.

1216 mm size.

Reducing Tee.

1620 x all branches.

Female branch TEE.

1216 X 1216 X 15 mm thread.

Female elbows:-

1216 X 15 mm thread.

Male thread connector:-

1216 X 15 mm thread.

Female thread connector:-

1216 X 15 mm thread.

Couplers:-

Reducers:-

Providing and laying in trenches galvanised mild steel tubes (Medium grade), tube fittings (Earth work in trenches to be measured and paid for separately) complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

20 mm nominal bore.

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipes complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Fixing water metre and stop cock in galvanised mild steel tube 20mm nominal bore including necessary fittings such as mild steel galvanised jam nut, socket etc. cutting and making long screws complate (water meter and stop cock to be paid for separately). complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 1000 litres net capacity PVC water storage tank of ISI : 12701 marked,G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 110x90mm PVC. floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge .

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fitting with approved adhesive etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

150 mm dia

110 mm dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

150 mm dia

110 mm dia

Providing and fixing PVC door bend with oval acces door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

150 mm dia

110 mm dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

150 mm dia

110 mm dia

Providing and fixing PVC single equal branch with oval access door , ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

150 mm dia

110 mm dia

Providing and fixing PVC cowl complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

150 mm dia.

110 mm dia.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc.complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

150 mm dia

110 mm dia

Providing and fixing viterous China water closet squatting pan (European Type W.C. pan) of CERA size 580mm (Earth work, bed concrete, foot rest and traps to be measured and paid for separately complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge Anglo Indian Universal closet of CERA

Providing and fixing PTMT White high density polyethylene / poly ropylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and providing and fixing making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing 110 mm PVC ‘P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc.complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing wash basin cat no 10001 of size 55x40 cm of hind ware or its equivalent in white shadewith single hole for pillar tap with C.I. or M.S. brackets painted white inculding cutting hole and making good the same but exculding fittings flat back as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing stainless steel sink of approved standard IS marked with drain board and C.P. waste with C.I. or M.S. brackets painted white including cutting holes in walls and making good the same but excluding fitting size 460x560x229 mm. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 32 mm dia C.P. brass waste (heavy duty ISI marked IS:8931 & 8934) for wash basin or sink . complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing 32 mm dia PVC waste pipe for wash basin or sink including check nut . complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing & fixing 600mm x 450mm ( six hundred milimetre into for hundred fifty milimetre ) bevelled edge mirrior of superior glass mounted on 6mm (six milimeter ) thick A.C. sheet or plywood sheet & fixed to wooden plugs with C.P.brass screws & washers as per HP.PWD., specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing and fixing 600mmx120 mm glass shelf with C .P brass and guard rail complete, fixed to wooden plugs with C. P brass screw complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing & fixing 100 mm dia C.P. grating for floor or nahani / gully / floor trap complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing brass full way valve with wheel complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

15mm nominal bore.

20mm nominal bore.

Providing and fixing CP brass bib tap (heavy duty ISI marked IS:8931 & 8934) 15mm dia of jaquar with capstan head complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing CP brass pillar tap 15mm dia of jaquar with capstan head (heavy duty ISI marked IS:8931 & 8934). complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing 45cms long CP connection pipe15mm nominal bore (heavy duty ISI marked IS:8931 & 8934) with brass union complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing C.P.brass angle valve 15mm dia of jaquar (heavy duty ISI marked IS:8931 & 8934) complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing water pump to lift to rain water complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing chromium plated brass soap dish ESS-ESS/Jal make with C.P Brass brackets fixed to wooden cleats with C.P brass screws as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Smoke testing of soil or ventilating pipes (new or old) any height iof diametre together with the length of drain connecting the soil pipe with the nearest manhole (including the use of ladders. For waste pipe complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing stone ware gully trap completewith CI grating brick masonry in cement mortar 1:5 (one cement isto five sand) complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Constructing manhole with R.C.C top slab in 1:2:4 mix in (one cement isto two sand ist: four graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (one cement isto four sand isto eight graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (one cement isto three sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (one cement isto two sand isto four graded stone aggregate 20mm nominal size) finished smooth complete. including curring complete and testing the same Inside size 800mm x 800mm and 500mm deep including CI cover with frame light duty for 455 mmx610mm internal dimensions of man hole complete total rate of cover and frame to be not less than 38 kg with 200 mm thick walls of brick masonry in cement mortar 1:3 (1 cement : 3 sand) complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Constructing brick masonry chamber for under ground CI inspection chamber and bends with common brunt clay buildings bricks in cement mortar 1:5 (one cement isto five sand) CI cover with frame (light duty) 355mmx610mm internal dimension total weightr 9of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) RCC top slab with 1:2:4 mix in (one cement isto two sand ist: four graded stone aggregate 20mm nominal size) foundation concrete1:5:10 (one cement isto five sand isto ten graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (one cement isto three sand) finished smooth with a floating coat of neat cement on walls and bed concrete 1etc complete inside dimensions of 455x610x450 mm deep single pipe lane complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Supplying and fixing CI cover with frame for gully trap 300 mm X 300 mm (standard pattern) the weight of cover not less than 4.53 kg complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing P.V.C. connection pipe with brass union as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying P.V.C. (phinolex) pipe 110 mm dia ISI marked for soil waste and ventilating pipe and fixing of joints with approved adhesive including cutting holes in walls and making the same complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Supplying fixing CI cover without frame for main hole as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

for frame of internal diamansion 455x610mm (four hundred fifty five into six hundred ten milimetres) rectangular IC Cover (light duty single seal pattern-I) the weight of cover to be not less than 23 kg) complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

for frame of internal diamension 500 mm diametre (ive hundred milimetres) CI cover (medium duty) the weight of cover to be not less than 58kg) complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge

Providing and fixing 110 mm dia PVC cowl complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Manishsharma

Vidya Dutt Sharma

BAL KRISHAN