Provn of 04 Single Living Accn for JCOs at Suratgarh Mil Stn

Amount

Surface dressing not exc 15cm deep in soft/loose soil complete all as specified and as directed.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavating in trenches, not exc 1.5 metre wide and not exc 1.5 metre in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. laying cables, pipes, etc. not exc 10 Sqm on plan & not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete all as specified and as directed.

Removing excavated soil/material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and as directed.

Earth filling under floors or in foundations and similar locations including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and as directed. Note :- Soil obtained from excavation under serial item No. 1.00 here-in-before shall be used for filling under floors.

M&L for anti-termite treatment to the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified & as directed.

M&L for anti-termite treatment to the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified & as directed.

M&L for anti-termite treatment to the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified & as directed.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for cement concrete (1:2:4) type B1 using 20 mm graded crushed stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, roof kerbs, mud stops and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed.

M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed. Note :- Reinforcement shall be measured and paid for separately under respective item of this Schedule.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like complete all as specified & as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like complete all as specified & as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like complete all as specified & as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded crushed stone aggregate in chajjas and the like complete all as specified & as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded crushed stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span and the like complete all as specified & as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded crushed stone aggregate as in chullah hoods, stairways and the like complete all as specified & as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded crushed stone aggregate as in Fins, fascias, louvres, parapets, and railings exc 60cm in height, newels, balustrade and the like complete all as specified & as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

Supply only integral liquid water proofing compound (ISI marked) complete all as specified & as directed.

M&L for brick work with old size Fly Ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with old size burnt clay sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 complete all as specified and as directed. Note : Brick work under this item shall be carried out in sewage disposal work (i.e. manholes) and area drainage work (i.e. drains).

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete complete all as specified & as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete complete all as specified & as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified & as directed.

Formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete complete all as specified & as directed.

Formwork to flat surfaces of chajjas, chullah hoods, troughs and similar items including edges for rough finished surfaces of concrete complete all as specified & as directed.

Formwork to edges of concrete flats, roofs, floors etc and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces of concrete complete all as specified & as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window / Ceosetory windows & other Frames/ Chowkhat of size 50x100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in-Charge.

Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24(a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & as directed.

S&F factory made 30mm thick flush shutter, solid core construction, with block board core and plywood face panels, both faces covered with decorative face veneer with lipping to match complete all as specified and as directed.

S&F 125mm butt hinges, heavy weight, cold rolled mild steel (ISI marked) complete all as specified and as directed.

S&F butt hinges of size 100mm extruded aluminium alloy powder coated with galvanized mild steel hinge pin, anodized type B-21 complete all as specified and as directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

S&F extruded aluminium alloy handle, 100mm size, fabricated type, anodized (ISI marked) complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

Supply and fixing Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F stainless steel drapery rod of 25mm inner dia & 1.6mm wall thickness (in lengths as directed) with & including stainless steel sockets & decorative finial at both ends and pair of stainless steel brackets & stops fixed at both ends with PVC rawl plug & steel screws on walls/beam complete all as specified & as directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, framed signed boards, walk ways, railings, framework of water tanks and similar work including welding conforming to Grade E-165 (Fe 290), complete all as specified & as directed.

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed.

All as per serial item No. 45.00 here-in-before but 6 to 10 mm dia in stirrups, spacers and binders complete all as specified & as directed.

Supply and fixing 1mm thick factory made pressed steel shutter fixed with 1.25mm thick pressed steel framed 105x60mm and as required for cupboards (consisting two shutters) including 06 Nos hinges of size 100mm long and Godrej pattern three way locking system with suitable shape & size 12mm dia MS rod & 01 Nos chromium plated handle of size 150mm long with & including two coats of shop spray synthetic enamel painting over a coat of red oxide primer as colour approved by GE. Note : Cupboards frame to be fixed with 06 Nos nuts & bolts of dia 12mm & 150mm long at vertical outer edge of cupboards brick wall /concrete surface including making good the distrubed surfaces complete all as specified and directed.

S&F factory made pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, complete as specified & as directed.

S&F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, complete as specified & as directed.

S&F factory fabricated pressed steel frame/box windows, ventilators with glazed and fly proof shutters provided to size and dimensions as specified & shown on drawing No. BTD-888R Sheet No. 1/5 to 5/5 & BTD-889 Sheet No. 1/4 to 4/4 with & including MS grill, MS fillets, pintol hinges, tower bolts, MS handles, peg stays, MS lugs, locking arrangement, dash through bolt where required, etc complete all as specified & as directed. Notes : (i) PCC for filling in frames, glass, wire gauge and painting shall be measured & paid for separately under respective items. Provision of all other items as shown & specified on drawings shall deemed to be included in quoted rate of this item. (ii) The quoted rate shall deemed to include provision of cutting holes of suitable depth in walls for inserting lugs etc and making good dismantled portion in PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate and CM (1:3).

S&F factory fabricated pressed steel frame/box windows, ventilators without glazed and fly proof shutters provided to size and dimensions as specified & shown on drawing No. BTD-888R Sheet No. 1/5 to 5/5 & BTD-889 Sheet No. 1/4 to 4/4 with & including MS grill, MS fillets, pintol hinges, tower bolts, MS handles, peg stays, MS lugs, locking arrangement, dash through bolt where required, etc complete all as specified & as directed. Notes : (i) PCC for filling in frames, glass, wire gauge and painting shall be measured & paid for separately under respective items. Provision of all other items as shown & specified on drawings shall deemed to be included in quoted rate of this item. (ii) The quoted rate shall deemed to include provision of cutting holes of suitable depth in walls for inserting lugs etc and making good dismantled portion in PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate and CM (1:3).

M&L for wire brushing and cleaning of concrete surface on top of roof providing 15mm thick plaster (screed bed) over roof slab in cement and sand mortar 1:4, mixed with integral liquid water proofing compound as per manufacturer’s instructions including 40mm thick cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) complete all as specified and as directed. Note : Supply only integral liquid water proofing compound shall be measured and paid for separately.

M&L for APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick, reinforced with polyester non woven fabric (weighing not less than 150 gms/sqm) laid on primed surface complete all as described in Para 11.44.5 of SSR Part-I, complete all as specified and as directed. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps.

M&L for 75mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even, complete all as specified and as directed.

M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded crushed stone aggregate as in sub base, surface finished fair and even, complete all as specified and as directed.

M&L for machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 20mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed.

M&L for machine cut Kota stone slab 15 to 18mm thick on vertical surfaces such as dado, skirting etc. laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 7mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (i.e 450mm x 300mm or as directed), on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for Non skid ceramic tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

Material and labour for factory made 60mm thick machine pressed precast cement concrete coloured designer polished (reflecting type) interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment with coloured top casted in an automatic plant working on vibration and simultaneous hydraulic compression from top, laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & as directed. Note : Shape & colour of paver blocks shall be as approved by the GE.

M&L for 75mm thick PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate as in plinth protection surface finished even and smooth without using extra cement complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid with an outward slope of 1:30 in alternative bays not exceeding 4 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for rendering 15mm thick in cement and sand mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in cement and sand mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished even & smooth without using extra cement, complete all as specified and directed. Note : Supply only integral liquid water proofing compound shall be measured and paid for separately.

M&L for rendering 5mm thick in cement and sand mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement and sand mortar 1:3 complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick white wall care putty complete all as specified & as directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick white wall care putty complete all as specified & as directed.

Material & Labour for applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified & as directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified & as directed.

S&F 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified & as directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified & as directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified & as directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings, complete laid in trenches, complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade of 25mm bore with & including all fittings, complete laid in trenches, complete all as specified and as directed.

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.

S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms) complete all as specified and as directed.

S&F vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic WC seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device, Jet spray (brass chromium plated of butterfly shape) with 1.00m PTMT tube suitable for 15 mm bore GI pipe with PTMT nut & nipple, complete all as specified & as directed.

S&F PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified & as directed.

S&F vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified & as directed.

S&F PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified & as directed.

S&F 15mm bore bib tap, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & as directed.

S&F 15mm bore Stop valve, fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union complete all as specified & as directed.

S&F 15mm bore Angle stop valve, fancy type, cast copper alloy chromium plated, screwed down, high pressure with crutch of butterfly handle, screwed both ends for iron pipe or for union complete all as specified & as directed.

Supply and Fixing 20mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified & directed.

Supply and fixing 25mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified & directed.

S&F brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe of 15mm bore or union complete all as specified and as directed.

S&F tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified and as directed.

S&F Soap dish holder brass chromium plated fixed on wall with PVC rawl plug & cadmium plated brass screws complete all as specified & as directed. Make :- Cat Part No BA-45 of make – Prayag or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified & as directed.

S&F stainless steel Peg Set of Six of standard size (not less than 300mm long) fixed to wall with two rawl plugs and chromium plated brass screws complete all as specified & as directed. Make :- Cat Part No BEA-30 of make – Prayag or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls complete all as specified & as directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls complete all as specified & as directed.

S&F 110mm bore PVC (SWR) bend any redius, joint with solvent cement complete all as specified & as directed.

S&F 75mm bore PVC (SWR) bend any redius, joint with solvent cementcomplete all as specified & as directed.

S&F 110mm bore PVC (SWR) Junction double, (double T), equal or unequal with access door complete all as specified & as directed.

S&F PVC (SWR) gully trap 125/110mm bore, setting and jointing with solvent cement complete all as specified & as directed.

S&F PVC (SWR) multi floor trap plain with PTMT grating including jointing with solvent cement, diameter of outlet 75mm, complete all as specified & as directed.

S&F 32mm dia PVC flexible waste pipe 75cm long with 32mm dia socket for union complete all as specified and as directed.

S&F stainless steel grating 100mm dia of PTMT (Minimum weight 25 gms) over floor trap in white / grey cement to match with existing floor complete all as specified and as directed.

M&L for DWCPE pipe 180mm (OD)/163mm (ID) dia, laid in trenches, complete with necessary fittings, laid and jointed on concrete bed complete including earth work, removal, returning filling, jointing and testing, including laid PCC 1:3:6 type C2 using 40mm graded stone aggregates including packing under haunching against sides of pipe laid all as per IS 16098 : 2013 fixed in repair complete all as specified & as directed.

M&L for PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested for 180mm bore pipe complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and as directed.

M&L for PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in concave shape benching (gola) of 80mm radius at Junctions of roof/terrace with parapets/ side walls with surface finished even & smooth without using extra cement complete all as specified and as directed.

M&L for construction of Septic Tank for 10 to 25 users, brick construction, complete, all as specified and shown on drawings (BTD-016 Sheet No. 1/3 to 3/3).

M&L for construction of Soak Well for 10 to 25 users, brick masonry, complete, all as specified and shown on drawings (BTD-830 Sheet No. 1/1).

M&L for Valve Pit of internal size 120cm x 120cm x 120cm built in brick masonry complete all as specified in Particular Specifications and as shown on drawing No. BTD-811 Sheet No. 1/2 & 2/2 .

Cutting existing steel tubing for alterations or additions (Each cut measured), necessarily done in position without taking down, 80 or 100mm bore pipe and making connection with 40mm bore GI Pipe complete all as specified & as directed.

M&L for point wiring for one light/fan/bell/buzzer point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including non-metallic rigid PVC concealed conduit (medium duty, ISI marked, not less than 20mm dia) with all fittings such as tee, bends, etc all as per IS, terminated in & including new sunk type pressed steel terminal boxes concealed in wall for mounting fittings like switches, sockets, regulators etc with and including 3mm thick phenolic laminated sheet top cover, complete all as specified and as directed. Note : Cost of cutting/leaving forming chases for conduits, sinking for boxes and making good in CM 1:4 shall deemed to be included in quoted rate of this item.

All as per serial item No. 112.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board with other switches complete all as specified and directed.

All as per serial item No. 112.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board complete all as specified and directed.

All as per serial item No. 112.00 here-in-before but for one light point controlled by two, two way switches complete all as specified and directed.

All as per serial item No. 112.00 here-in-before but for one bell or buzzer point controlled by one push button on same board with other switches or independent switch complete all as specified and directed.

All as per serial item No. 112.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) including 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed.

S&F switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts, ISI marked, complete all as specified and as directed.

S&F switch piano, flush type, single pole, two way, 5/6 Amp, 230 Volts, ISI marked, complete all as specified and as directed.

S&F Bell push, flush type, Single pole, 5 Amp, 230 Volts, ISI marked, complete all as specified and as directed.

S&F switch piano, flush type, single pole, one way, 15 Amp, 230 Volts, ISI marked, complete all as specified and as directed.

S&F socket outlet, 5 pin, 5/6 Amp, flush type, 230 Volts, ISI marked, complete all as specified and as directed.

S&F switch socket combination, 3 Pin 5/6 Amp and 6 Pin 15/16 Amps, flush type, 230 Volts, ISI marked, complete all as specified and as directed.

S&F ceiling rose, PVC/Polycarbonate insulated body, 65mmx50mm with three terminals, ISI marked, complete all as specified and as directed.

S&F lamp holder, PVC/Polycarbonate insulated body with back plate suitable for conduit/casing caping fittings, ISI marked, complete all as specified and as directed.

S&F 9 Watt LED lamp (Non-dimmable) of Standard / Universal size, Base - B22, Power Factor > 0.90, Lamp Efficiency > 80%,, Color Temperature - 3000 K, Lumen output - 900 lm, Colour Rendering Index (CRI) > 70, Warm white (WW) / Cool Day Light (CDL), 230 V, 50 Hz AC, ISI marked, complete all as specified and as directed.

S&F electronic fan regulator, flush type, stepped type with 5 step control, 230 Volts, 150 Watt, including making hole in sheet top cover and connecting up, ISI marked, complete all as specified and as directed.

Supply and fixing Bell ‘Ding Dong’ / ‘Multi Music’ Type, AC, 230 Volts, ISI marked, complete all as specified and as directed.

S&F LED mirror fitting of minimum and including lamp 1x10 Watt, 6000 K, 2 feet, complete with decorative ultra ceiling square profile linear LED lighting fixture with extruded polycarbonate environment friendly cover complete with connection with 2 core flexible copper cable 23/0.00076 from ceiling rose to light fitting connection with following specification, complete all as specified and as directed :- (a) Lumen efficacy of system should be minimum 105 Lumen per watt. (b) Voltage operating range : 160 to 270 Volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max 10%. (f) IP rating : IP-20. (g) CRCA pre coated housing. (h) LED Driver of the make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection device for 2.5 KV. (l) CRI : Minimum 80

S&F LED batten fitting including T-8 retro LED 1x18 Watt, 6000 K, 4 feet, complete with decorative ultra ceiling square profile linear LED lighting fixture with extruded polycarbonate environment friendly cover complete with connection with 2 core flexible copper cable 23/0.00076 from ceiling rose to light fitting connection with following specification, complete all as specified and as directed :- (a) Lumen efficacy of system should be minimum 105 Lumen per watt. (b) Voltage operating range : 160 to 270 Volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max 10%. (f) IP rating : IP-20. (g) CRCA pre coated housing with two coloured plastic end caps. (h) LED Driver of the make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection device for 2.5 KV. (l) CRI : Minimum 80

Supply and Fixing Light Emitting Diode (LED) based street/security light fitting, 30 Watt with & including LED lamp, housing made up of LM6 pressure die cast aluminium alloy with effective thermal management, sturdiness, monolithic construction, totally enclosed, dust and water proof, minimum system efficiency of more than 100 lumens per watt and a minimum system lumen output of not less than 2500 lumens, correlated colour temperature shall be minimum 5700 degree Kelvin, Colour Rendering Index (CRI) shall not be less than 70, fitting shall be designed for a system life of 50,000 hours @ 70% lumen maintenance, ingress protection of IP-65 (minimum), mechanical impact resistance rating of IK ≥ 07, operating voltage range 140 V to 270 V, AC, frequency 50-60Hz, potted type for humming free operation, driver shall withstand upto 400 V for 08 hours, surge protection not less than 10 KV, Power factor > 0.95, Total Harmonic Distortion (THD) shall be less than 15%, double phase protection, no load, open circuit and short circuit protection, suitable for ambient temperature from (-)10°C to 50°C and humidity level 10% to 90% RH, cool white colour and lamp starting time shall not be more than 10 second, PMMA/ polycarbonate/ toughened glass heat resistant cover, prewired and connecting up to street light feeder/junction box with & including 2.5 Sqmm 3 core PVC insulated, weather proof, multistranded copper conductor cable of 1100 Volt grade (ISI marked), complete all as specified and as directed.

NOTES FOR LED LIGHT FITTINGS : (i) All LED light/luminare shall meet the provision laid down in IS - 16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part -II / Section 13. (ii) Contractor shall submit test report of LED street light fitting from Government accredited test laboratory for LM-79 and LM-80. (iii) Contractor has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of contract. The product will be replaced on site free of cost in the following case :- (a) Manufacturing defects. (b) Failure due to mechanical and electrical impact. (c) Drop in lumen (or lux at 1 m) below 90% of claimed values of lumen (or lux at 1 m) of the LED /Luminaries.

Supply and fixing mounting bracket (suitable for fixing/holding street/security light fittings) made of 40mm bore GI pipe ‘light grade’ not less than 1.50m long, bent to shape at required angle, fixed to Pole/wall with & including mild steel clamps (02 Nos) made out of flat iron 50x6mm with nuts, bolts & washers, matching with section of Pole/suitable for wall, complete all as specified and as directed.

S&F sheet metal enclosure, double door type, suitable for fixing MCBs, SPN with 200 Amps rated bus bar, 8 way, 240 Volts, flushed in wall fixed complete all as specified and as directed.

S&F sheet metal enclosure, double door type, suitable for fixing MCBs, SPN with 200 Amps rated bus bar, 4 way, 240 Volts, flushed in wall fixed complete all as specified and as directed.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volts, breaking capacity 10 kA, ‘C’ Curve, with over load and short circuit protection, fixed, complete all as specified and as directed.

S&F MCB, 6 to 32 Amps, SPN, 240 Volts, breaking capacity 10 kA, ‘C’ Curve, with over load and short circuit protection, complete all as specified and as directed.

S&F MCB, 63 Amps, SPN, 240 Volts, breaking capacity 10 kA, ‘C’ Curve, with over load and short circuit protection, fixed, complete all as specified and as directed.

Supply, assembling, hanging, fixing & testing Ceiling Fan of size 1200mm sweep, minimum air delivery 220 CMM with 5 star rated BEE, with brushless direct current (BLDC) motor, single phase 26W (+10%), P.F 0.90 (min), AC supply (input voltage range 120 to 280 volt), 230 Volt, with & including down rod, canopies, three number blades, capacitor 2.5 mfd, hook, rubber reel, safety pins, nuts, bolts, washers, cable connector and making connection with PVC insulated & sheathed 1.5 sqmm three core flexible copper multistranded conductor cable (ISI marked) from ceiling rose to connector of ceiling fan including marking of SM / MES number with thick synthetic enamel paint of approved tint complete all as specified and as directed. Note :- The font, style & place of writing SM/ MES number with synthetic enamel paint on ceiling fan shall be as directed by the Engineer-in-Charge and cost thereof shall deemed to be included in quoted rates.

Supply & fixing Exhaust fan of 300mm sweep, heavy duty, double ball bearing, copper wound, steel body, 900 RPM, Single Phase 230 Volt, 50 Hz AC supply complete with blades, frame and louver shutter and connecting up with & including three core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2 mm drawn into & including flexible PVC conduit and fixed by using 4 Nos, 100mm long 8mm dia bolt nuts and washers and grouted in wall in CM (1:3) with and including making suitable opening in existing wall complete all as specified & as directed

Supply, installation & testing electric Geyser (water storage type) of capacity 25 litre, vertical mounting type, glass lined inner tank, rust proof outer body, 2 KW heating element, suitable for 230V Single Phase 50 Hz AC supply, 5 Star rating, energy efficient, 8 Kg/sqcm pressure withstanding capacity, Class I, ISI marked, with & including Thermostat with Thermal Cutout, heating indicator, Multi functional valve (acts as pressure release valve, non-return valve, expansion valve and vacuum release valve), fixed all as per manufacturer’s instructions, fixed with & including ‘Anchor’ type /fastener type bolts & nuts (Set of 4 bolts of 10mm dia 150mm long with nuts & washers) into the wall grouted properly to hold the geyser and making good the disturbed surface as original, complete, all as specified & directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 7.50 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40 mm thick RCC pit cover, etc complete all as specified. Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner.

M&L for sub main wiring with two runs of 4 sqmm (nominal area) size main cable & one run of 4 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI marked cables, drawn through & including suitable size of heavy duty non-metallic rigid PVC concealed conduit ISI marked not less than 25mm dia & conduit fittings/accessories, fixed concealed in wall/ceiling complete all as specified and directed. Notes :- (i) 02 runs of 4 sqmm size main cable, 01 run of 4 sqmm size earth continuity conductor cable & conduit with accessories shall be measured as one run length for payment purpose. (ii) Cost of cutting/leaving forming chases for conduits and making good in CM 1:4 shall deemed to be included in quoted rate of this item.

Supply, laying, jointing and testing LT XLPE insulated screened, bedded, galvanised steel strip or wire armoured heavy duty electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 16 sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified and directed. Notes :- (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

M&L for dry sand (Local Tibba sand) and punning for cushioning and cover for protection of under ground electric cable complete all as specified and as directed. Notes :-(i) Approved local Tibba dry sand free from vegetations, grass and other deleterious substances shall be used. (ii) For the purpose of payment, only punned thickness shall be measured.

M&L for sub class ‘B’ (old size) burnt clay bricks laid flat and dry abutting each other with gap between adjacent bricks not exc. 10mm for protection of underground electric cable in such a way that the length of brick is at right angle to the central axis of cable complete all as specified and as directed.

M&L for Galvanized iron tubing, 40mm bore light grade, ISI marked, including all fittings and laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (25mmx3mm) clamps, bolts, nuts and washers for protection of LT electric cable complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately.

BANSAL BROTHERS (BID ID -3137721)

Gill Construction Co (BID ID -3140087)

S.K BUILDERS AND ENGINEERS (BID ID -3146373)