Repair of furniture at Military Station Abohar.

Amount

TABLE 900 X 600mm with and without Drawer : Removing the exising UNSV top of table 3' X2' with / without drawer and S&F new top made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The top shall be fixed with 4mm thick TW edging all round all as per drg.

Removing of UNSV legs of table 3' X 2' with and without drawer and S&F of new legs as existing of Ist class hard wood .

Removing of UNSV long rails of table 3' X 2' with and without drawer and S&F of new long rails as existing of Ist class hard wood

Removing of UNSV side rails of table 3' X 2" with/without drawer S&F of new rail as existing of Ist class hard wood

Removing of UNSV drawer of table 3' X 2' with drawer and S &F new drawer as existing alongwith chromium plated knobs all as per drg.

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

TABLE CENTRE : Removing the existing u/s top of table centre & S&F of new top of size 900x450mm made out of prelaminated (one side) particle board 18/19mm thick including 4mm thick TW beading around.

Removing of old u/s legs of table centre S&F of new legs as existing of Ist class hard wood

Removing of u/s long rail of table centre S&F of new rails as existing of Ist class hard wood

Removing of old u/s short rail of table centre and S&F new short rail made out of 1st class hard wood as shown in the drg

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain glossy finish on all the exposed surfaces.

TABLE BED SIDE (MAP) :Removing the existing u/s top of table bed side S&F new top made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The top shall be fixed with 4mm thick TW edging all round all as per drg.

Removing of u/s side and replacing the same with one side teak faced prelaminated particle board

Removing the u/sdrawer and S&F new drawer made out of prelaminated partcile board and 12mm thick commercial plywood as specified in drg .

Removing the u/s back plywood , S&F new 6mm thick BWR grade plywood commercial as existing.

Removing the u/s legs and S&F new legs made out of ms square 18mm pipe with appropriate size screws and matching with black colour with other legs.

CHAIR DINING PVC SEAT AND CANE : Removing the u/s front legs , S&F new front leg as existing of Ist class hard wood

Removing the u/s Rear legs , S&F new Rear legs as existing of Ist class hard wood

Removing the u/s Front rail , S&F new Front rail as existing of Ist class hard wood

Removing the u/s Rear rail , S&F new Rear rail as existing of Ist class hard wood

Removing the u/s Side rail , S&F new Side rail as existing of Ist class hard wood

Removing the u/s Back Wooden , S&F new Back Wooden as existing of Ist class hard wood

Removing the u/s Stiffner , S&F new Stiffner as existing of Ist class hard wood

Removing of existing cane cleaning of cane holes and recanning with 2 mm wide new plastic cane for seat and 3.5 mm wide cane for borders of chair all as specified and shown on drg and as directed by Engr-in-charge. (For chair 0.40x0.39 = 0.156 Sqm)

Removing old u/s pvc seat from existing chair dining and S&F new PVC seat single piece 3mm thick weight not less than 0.39 Kgs with holes having 4 x 10mm thick ribs moulded all as specified in drg and as directed.

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

CHAIR DINING CUSHION : Removing the u/s front legs , S&F new front leg as existing of Ist class hard wood

Removing of old u/s Rear legs of Chair dining cushion and S&F of new Rear legs as existing of Ist class hard wood

Removing of old u/s front rail of Chair dining cushion and S&F of new front rail as existing of Ist class hard wood

Removing of old u/s Rear rail of Chair dining cushion and S&F of new Rear rail as existing of Ist class hard wood

Removing of old u/s Side rail of Chair dining cushion and S&F of new Side rail as existing of Ist class hard wood

Removing of old u/s Back wooden of Chair dining cushion and S&F of new Back wooden as existing of Ist class hard wood

Removing of old u/s Stiffner of Chair dining cushion and S&F of new Stiffner as existing of Ist class hard wood

Removing old u/s foam with cushion cover for seat of chair dining cushion and S&F new cool foam with cushion cover and cloh tapestry superior quality,colour ,pattern and quality as approved by GE/Engr -in-charge all as specified in drg .

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

CHAIR WRITING : Removing the u/s front legs , S&F new front leg as existing of Ist class hard wood

Removing the u/s Rear legs , S&F new Rear legs as existing of Ist class hard wood

Removing the u/s Arms , S&F new Arms as existing of Ist class hard wood

Removing the u/s Front rail , S&F new Front rail as existing of Ist class hard wood

Removing the u/s Rear rail , S&F new Rear rail as existing of Ist class hard wood

Removing the u/s Side rail , S&F new Side rail as existing of Ist class hard wood

Removing the u/s Stiffner , S&F new Stiffner as existing of Ist class hard wood

Removing the u/s Teak wood back , S&F new Teak wood back as existing of Ist class hard wood.

Removing of existing cane cleaning of cane holes and recanning with 2 mm wide new plastic cane for seat and 3.5 mm wide cane for borders of chair all as specified and shown on drg and as directed by Engr-in-charge.

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

CHAIR EASY : Removing the u/s front legs , S&F new front leg as existing of Ist class hard wood

Removing the u/s Rear legs of chair easy , S&F new Rear leg as existing of Ist class hard wood.

Removing the u/s Arms , S&F new Arms as existing of Ist class hard wood

Removing the u/s Front rail , S&F new Front rail as existing of Ist class hard wood

Removing the u/s Rear rail , S&F new Rear rail as existing of Ist class hard wood

Removing the u/s Side rail , S&F new Side rail as existing of Ist class hard wood

Removing the u/s Top/Bottom rail Back frame , S&F new Top/Bottom rail Back frame as existing of Ist class hard wood

Removing the u/s Side rail Back frame , S&F new Side rail Back frame as existing of Ist class hard wood

Removing of existing cane cleaning of cane holes and recanning with 2 mm wide new plastic cane for seat 3.5 mm wide cane for borders of chair all as specified and shown on drg and as directed by Engr-in-charge. (For chair Seat 0.51x0.45=0.2295 Sqm) (Back 0.43x0.34=0.1462 Sqm) Total 0.3757 Sqm

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

PEG TABLE : Removing the existing u/s top of peg table , S&F new top made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The top shall be fixed with 4mm thick TW edging all round all as per drg.

Removing the u/s leg , S&F new leg as existing of Ist class hard wood

Removing the u/s long rail , S&F new long rail as existing of Ist class hard wood

Removing the u/s short rail , S&F new short rail as existing of Ist class hard wood

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

TEAPOY : Removing the existing u/s top of Teapoy S&F new top made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The top shall be fixed with 4mm thick TW edging all round all as per drg.

Removing the u/s leg , S&F new leg as existing of Ist class hard wood

Removing the u/s Stiffner , S&F new Stiffner as existing of Ist class hard wood

Removing the u/s long rail , S&F new long rail as existing of Ist class hard wood

Removing the u/s short rail , S&F new short rail as existing of Ist class hard wood

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

SIDE BOARD : Removing of u/s back , S&F new back of side board with 6mm thick BWR grade commercial ply wood as existing and as per drg.

Removing the existing u/s shutter, S&F new shutter as existing made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The shutter shall be fixed with 4mm thick TW edging all round as per drg and fixed with aluminium anodised knob with ball spring catch.

Removing the u/s leg , S&F new leg as existing of Ist class hard wood

Removing of u/s drawers, S&F new drawers made out of 12mm commercial plywood and fixed with aluminium anodised knob all as per existing and shown on drg.

Removing of U/S shelves from side board and S&F new shelves as per existing shape & size made out of 18mm thick particle board one side teak faced.

Removing of U/S side of side board and S&F new side made out of 18 mm thick prelaminated particle board as per existing shape & size

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces including inside of shutter

TABLE WRITING: Removing the exising UNSV top of table writing and S&F new top made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The top shall be fixed with 4mm thick TW edging all round all as per drg.

Removing unsv shutter and S&F new shutter made out of 18mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side.Shutter shall be fixed with 4mm thick TW edging all round and one aluminium anodised knob all as shown on drg.

Removing unsv legs and S&F legs as existing of Ist class hard wood

Removing unsv bottom stiffner S&F new stiffner of bottom as existing of Ist class hard wood.

Removing unsv drawer and S&F new drawer of table writing as existing and fixed with aluminium anodised knob. Rest all as per existing and as specified in drg.

Removing of U/S back ply from table writing and S&F new back ply of 6mm thick commercial plywood as per existing shape & size

Removing unsv bottom of box and S&F new botom of table writing with 18mm prelaminated particle board as per existing shape & size and as specified in drg.

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces including inside of shutter

TABLE DRESSING LADIES :Removing unsv back ply of mirror and S&F new 6mm commercial plywood to back of mirror as per existing shape and size as per drg

Removing unsv wooden member and S&F new Teak wood member for holding mirror alongwith mirror frame alround as existing.

Removing unsv top of box and S&F new top made out of 19mm thick Prelaminated particle board one side teak shade to the top of table dressing ladies all as per drg with 4mm thick Teak wood edging.

Removing unsv alluminium channel and S&F new 12x22mm Aluminium channel for sliding glass all as per drg

Removing unsv leg and S&F new leg as existing of Ist class hard wood

Removing unsv mirror and S&F new looking mirror of 5mm thick all as per drg and as existing

Removing unsv knob and S&F new aluminium anodised knob to drawer

Removing unsv drawer and S&F new drawer all as per existing size made out of 12mm thick commercial plywood.

Removing unsv Cushion with cover for Stool dressing of dressing ladies and S&F new Cushion with cover all as per existing size .

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces

TABLE DRESSING GENTS WITH MIRROR :Removing unsv back ply of mirror and S&F new 6mm thick ply wood to back of mirror as per existing shape & size

Removing unsv wooden member and S&F new TW member for holding of mirror alongwith mirror frame as per Drg

Removing unsv mirror and S&F new looking mirror of 5mm thick as per existing shape & size

Removing unsv knobs and S&F new aluminium anodised knob to drawer

Removing unsv drawer and S&F new drawer all as per existing size made out of 12mm thick commercial plywood.

Removing unsv Side to side board for dressing of Dressing Gents and S&F new Side to side board 18mm Prelaminated particle board all as per existing size .

Removing unsv Glass shelf of dressing ladies and S&F new Glass shelf all as per existing size .

Removing unsv catcher for Looking Mirror of dressing ladies and S&F new catcher all as per existing size .

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces

TABLE DINING 6 /4PERS : Removing the existing u/s top of Table and S&F new top made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The top shall be fixed with 4mm thick TW edging all round all as per drg.

Removing the unsv legs and S&F new legs as existing of Ist class hard wood

Removing the existing u/s top rail and S&F new rail as existing of Ist class hard wood

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces

TABLE DINING 8 PERS : Removing the existing u/s top of Table and S&F new top made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The top shall be fixed with 4mm thick TW edging all round all as per drg.

Removing the unsv legs and S&F new legs as existing of Ist class hard wood

Removing the existing u/s top rail and S&F new rail as existing of Ist class hard wood

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces

BED HARD PLY WOOD TOP :Removing unsv plywood and beading of head board and S&F new teak veneered decorative plywood 4mm thick to both sides of the head board including fixing 6mm thick teak wood beading all round and as exising and as specified in drg .

Removing unsv plywood and beading of foot board and S&F new teak veneered decorative plywood 4mm thick to both sides of the foot board including fixing 6mm thick teak wood beading all round and as exising and as specified in drg .

Removing of unsv long rail & S&F new long rail made out of well seasoned teak wood as per existing shape & size

Removing of unsv support short rail and S&F new short suport rail made out of TW as existing and as per drg.

Removing of unsv legs and S&F new leg made out of well seasoned teak wood as per existing shape & size and as shown on drg.

Removing unsv ply wood top and S&F new ply wood 12mm thick commercial BWR grade with appropriate size MS screws 08 Nos as exising and as specified in drg

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

SOFA SET 1/4/ 5 SEATER : S&F 32 density 530x560x100mm cool foam cushion covered with cloth tapestry superior quality , colour, pattern and quality as approved by GE/Engr-in-Charge. Make of cushion - SAMRAT/ Sleepwell /Kurlon. Each cushion cover shall be provided with one side openable zip. (Note:- Rate of tapestry cloth shall not be less than Rs.250 per RM.)

S&F cushion cover only of size 530x560x100mm cloth tapestry superior quality , colour, pattern and quality as approved by GE/Engr-in-Charge. Each cushion cover shall be provided with one side openable zip. (Note:- Rate of tapestry cloth shall not be less than Rs.250 per RM.)

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces to sofa set 5 seater .

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces to sofa set Singal seater

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces to sofa set 4 seater

CHARPOY GI PIPE AND/IP HARD TOP: Removing of old unservicable existing elbows and S & F new GI elbowsThree way 32mm dia ISI Mark all as specified & directed

Removing of old unserviceable broken checknuts and S & F new GI check nuts for 32mm GI pipes ISI Marked all as specified & directed

Removing of existing unseviceable long rails from Charpoy GI pipe and S & F new long rails made out of GI pipe 32mm bore medium grade as per existing shape & size complete as specified & directed .

Removing exsting damaged short rails and fixing short rails to charpoy after conversion from retrieved old long rails duly threaded at both ends and fixing the same as per exsting shape & size complete all as directed .

Removing exsting damaged legs and fixing legs after conversion from retrieved old short rails duly threaded at one end and another side welding with 3mm thick MS sheet base and mild steel brackets of required size, shape for fixing MNF set all as shown on drawing and as directed .

M & L for welding to broken / cracked joints of charpoy GI pipe 32 mm dia (i.e) short rail, long rail, legs etc) by gas welding as per existing design rest all as specified and directed by Engineer-in-Charge.

Removing exsting unserviceable plywood from charpoy GI pipe and tightening entire frame and supply and fix 12mm thick plywood of BWR grade commercial of size 1980 x 900mm (Make : Archid /century /Greenply) fixed with flat head nut of size 5mm dia 60mm long, bolt with washer (Total 06 Nos per charpoy) including drilling holes in ply and steel frame of charpoy . Rest all as specified and directed by GE/Engr-in-Charge.

Removing exsting unserviceable plywood from charpoy IP Hard Top, entire frame and supply and fix 12mm thick plywood of BWR grade commercial of size 1980 x 900mm (Make : Archid /century /Greenply) fixed with flat head nut of size 5mm dia 60mm long, bolt with washer (Total 06 Nos per charpoy). Rest all as specified and directed by GE/Engr-in-Charge.

Retaping of Charpoy GI Pipe with new nylon newar 50 mm to 55 mm wide 4 ply in white/light colour of approved quality including removing of old/unserviceable nylon newar and tightening of charpoy frame complete all as specified and directed by Engineer-in-Charge. Make : As per sample kept in furiture yard/BSO Office

Chair Varandah : M & L for repair / fixing of broken parts of chair varandah by welding (Gas Welding) as existing with 20mm dia MS Conduite pipe where ever required as directed.

M & L for preparation of surfaces and painting of chair varandah with two coat of synthetic enamel paint white as specified and directed.

Removing of old exsting cane and recanning of chair varandah with new 4mm width 0.60mm thick cream colour plastic cane of approved quality as specified in drg and as directed.

Removing of old unserviceable PVC seat and back from chair varandah and S&F new PVC seat and back 4mm thick weight not less than 1.85 Kgs for both seat and back having 4 x 10mm thick ribs moulded complete all as specified and as directed by Engineer-in-Charge Make: Amko/Cello/Harmony

Supply and Fix new hard rubber shoes superior quality (as approved) of required size to chair varandah as directed.

REPAIRS TO CHAIR CB STEEL WITH ARMS: Removing of old unserviceable back frame of chair CB steel with arms and supply and fix new back frame made out of seasoned teakwood duly canned as per trade pattern. The chair shall be fixed with FI 3mm thick 14 X 25mm clips 02 Nos each on either side of back duly welded and also making holes to back frame centre to centre by drilling machine for fixing back frame with steel pipes by required size screws for extra support as directed.

Removing of old unserviceable seat frame of chair CB steel with arms and supply and fix new seat frame made out of seasoned teakwood duly canned as per trade pattern. The chair shall be fixed with FI 3mm thick 14 X 25mm clips 02 Nos each on either side of seat duly welded and also making holes to seat frame centre to centre by drilling machine for fixing seat frame with steel pipes by required size screws for extra support as directed.

Removing of old unserviceable hand rest and supply and fix new hand rest made out of well seasoned teakwood with required size screws. The hand rest shall be french polished with black colour all as specified, directed and as shown on drawing.

M & L for preparation of surfaces and painting of chair CB Steel With Arms with two coat of synthetic enamel paint Olive Green. All as specified and directed.

ALMIRAH LARGE STEEL WITH SHELVES: Removing unsv legs of almirah and S&F new legs made out of 1mm thick MS sheet as existing by welding / revitting as per drg and as directed.

Removing of unsv shelves from almirah Large steel. S& F of new shelves made of 1.00mm thick MS sheet of same shape & size as existing

Removing of UNSV 3 way locking device. S&F complete new locking device of same shape & size as existing and as per drg.

Removing of UNSV handle from almirah large steel. S&F new CP handle 150mm long as approved and directed.

Removing of old UNSV locks. S&F new brass lock 6 levers to almirah as approved .

M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying synthetic enamel paint of required colour internally and externally by spray painting complete all as specified and as directed by Engr-in-Charge

ALMIRAH MEDIUM STEEL WITH SHELVES: Removing unsv legs of almirah and S&F new legs made out of 1mm thick MS sheet as existing by welding / revitting as per drg and as directed.

Removing of unsv shelves from almirah medium steel. S& F of new shelves made of 1.00mm thick MS sheet of same shape & size as existing

Removing of UNSV 3 way locking device. S&F complete new locking device of same shape & size as existing and as per drg.

Removing of UNSV handle from almirah med steel. S&F new CP handle 150mm long of approved make.

Removing of old UNSV locks. S&F new brass lock 6 levers to almirah as approved .

M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying synthetic enamel paint of required colour internally and externally by spray painting complete all as specified and as directed by Engr-in-Charge

TABLE OFFICE OFFICER: Removing unsv top of table and S&F new top to table office officer steel made out of 18mm thick preleminated particle board with 6mm thick teak wood beading edging alround the top.

Removing of old UNSV drawers from table office Officer steel and S&F new drawers made of 1.00mm thick sheet of same shape & size as existing.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Removing of UNSV locks from table office Officer steel and S&F of new brass locks of 6 lever with duplicate key of approved quality as approved by GE/Engr-in-Charge.

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as specified and directed by Engineer-in-charge

TABLE OFFICE CLERK STEEL: Removing unsv top of table and S&F new top to table office clerk steel made out of 18mm thick prelaminated particle board with 6mm thick teak wood beading edging alround the top.

Removing of old UNSV drawers from table office clerk steel and S&F new drawers made of 1.00mm thick sheet of same shape & size as existing.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Removing of UNSV locks from table office clerk steel and S&F of new brass locks of 6 lever with duplicate key of approved quality as approved by GE/Engr-in-Charge.

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as specified and directed by Engineer-in-charge

TABLE 3' X 2' WITH DRAWER STEEL: Removing unsv top of table and S&F new top to table steel made out of 18mm thick prelaminated board with 6mm thick teak wood beading edging alround the top.

Removing of old UNSV drawers from table 3' x 2' steel and S&F of new drawers made of 1.00mm thick sheet of same shape & size as existing.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as per specified.

TABLE 3' X 2' WITH OUT DRAWER STEEL: Removing unsv top of table and S&F new top to table steel made out of 18mm thick prelaminated board with 6mm thick teak wood beading edging alround the top.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as per specified.

TABLE 3' X 3' STEEL: Removing unsv top of table and S&F new top to table steel made out of 18mm thick prelaminated board exterior grade with 6mm thick teak wood beading edging alround the top.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as per specified.

LOCKER BED SIDE STEEL : Removing unsv legs of locker and S&F new legs made out of 1mm thick MS sheet as existing by welding / revitting as per drg and as directed.

Removing of unsv shelves from locker bed side steel. S& F of new shelves made of 1.00mm thick MS sheet of same shape & size as existing

Removing of UNSV hasp and staple of locker and S&F new hasp and staple of same shape & size as existing and as per drg.

Removing of UNSV handle from locker bed side steel. S&F new steel handle 100mm long of approved make.

Removing of old UNSV hanging rod S&F new hanging rod CP of 20mm dia to locker approved .

M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying synthetic enamel paint of required colour internally and externally by spray painting complete all as specified and as directed by Engr-in-Charge

CHAIR EXECUTIVE REVOLVING STEEL : (a) Removing old unsv seat of chair executive and S&F new seat made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(b) Removing old unsv back of chair executive and S&F new back made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(c) Taking out old unsv castors wheel from executive chair and S & F new twin wheel castors as per existing size and shape complete all as specified and as directed by Engr-in-Charge

(d) Removing unsv gas lift and S&F new gas lift of 100mm stroke length and gas pressure of 300n force as existing.

CHAIR WRITING STEEL: (a) Taking out old unsv cantilever type MS frame from chair and S & F new cantilever type ms tubular frame made out of 25mm x 10mm sec as per existing size and shape complete all as specified and as directed by Engr-in-Charge

(b) Removing old unsv seat of chair steel and S&F new seat made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(c) Removing old unsv back of chair steel and S&F new back made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(d) Removing unsv armrest and S&F new one piece armrest made of black integral skin polyurethane with MS insert to the chair as existing with appropriate size bolt and nuts as specified and as directed.

CHAIR COMPUTER : (a) Removing old unsv seat of chair computer and S&F new seat made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(b) Removing old unsv back of chair computer and S&F new back made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(c) Taking out old unsv castors wheel from chair computer and S & F new twin wheel castors as per existing size and shape complete all as specified and as directed by Engr-in-Charge

(d) Removing unsv gas lift and S&F new gas lift of 100mm stroke length and gas pressure of 300n force as existing.

BED HARD OFFRs STEEL : Removing unsv head board 18mm thick Prelaminated particle board exterior grade and S&F head board 18mm thick Prelaminated particle board exterior grade as exising and as specified in drg.

Removing unsv foot board 18mm thick Prelaminated particle board exterior grade and S&F foot board 18mm thick Prelaminated particle board exterior grade as exising and as specified in drg.

Repairing frame of Bed hard offrs steel size and section frame work including supports of MS square pipe 38mmx38mm section frame by arc welding where ever required as directed by Engr-in-Charge

Removing unsv ply wood top and S&F new ply wood 12mm thick commercial BWR grade with appropriate size MS screws 06 Nos as exising and as specified in drg

Material & labour for painting to the frame of bed hard offrs steel with one coat of synthetic enamel paint black all as per specified.

CHAIR WRITING BLOW PLAST/ORNATE SUPREME : Removing old unsv seat of chair writingd blow plast/Ornate supreme and S&F new seat 4 Nos nuts &bolts as per existing .The quality & shade/colour of the cover of seat should match with the existing shade/colour as approved & directed by Engr-in-Charge.

Removing old unsv back of chair writing blow plast/Ornate supreme and S & F new back with 4 Nos nut & bolt as per existing. The quality & shade/colour as approved & directed by Engr-in-Charge.

COMPUTER TABLE : Removing unsv top of computer table and S&F new top made out of 18mm thick prelaminated board with 6mm thick teak wood beading edging alround the top.

Removing of old UNSV drawers of computer table and S&F of new drawers made of 18mm thick prelaminated board with 6mm thick teak wood beading edging alround the drawer of same shape & size as existing.

Removing of old UNSV key board of computer table and S&F of new key board made of 18mm thick prelaminated board with 6mm thick teak wood beading edging alround the drawer of same shape & size as existing.

Material & labour for painting to the frame of computer table with one coat of synthetic enamel paint olive black paint all as per specified.

PAINTING OF STEEL FURNITURE: M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying two coats of synthetic enamel paint of required colour internally and externally by spray painting complete all as specified and as directed :-

Side rack steel 3 spaces

Trestle store room steel

Rack steel 1830x760x1905mm

Rack 6 tier steel

PACHNANDA BUILDERS