Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹29.2 LAdmitted-Finance | ₹29.2 L | L1 | Admitted-Finance |
| 2 | L2₹35.3 LAdmitted-Finance | ₹35.3 L | L2 | Admitted-Finance |
| 3 | Not Admitted-Fee | - | - | Not Admitted-Fee Others-EMD not Received on due date and time as per NIT condition |
| 4 | Not Admitted-Fee | - | - | Not Admitted-Fee Others-EMD not Received on due date and time as per NIT condition |
| Sl No | Description | Qty | Unit | annapurna construction L1 | HI - TECH POWER L2 |
|---|---|---|---|---|---|
| 0.00Imp. Note - 1. The bidder must possess valid EPF & ESIC registration. The bidders need to deposit EPF & ESIC with appropriate authority. The reimbursement for EPF & ESIC deposit shall not be made. 2. The payment of wages to labourers should be made through bank. 3. The bidder must possess sufficient manpower & other resources (as detailed in SGF ) required for the timely completion of work. | |||||
| 1.00 | Sweeping of black topped/concrete road surfaces/footpath including berm portions to give a neat clean appearance including removing all debris, stones, vegetation, grit etc. including cost of brooms, baskets, tools & tackles etc and disposing off the same to the near by pits/ditches within a lead of 100 mtrs. complete as per specifications and as directed by Engineer-in-charge. Note: 1) Measurement shall be taken for black topped portion and water table or footpath portion only. Adjoining berms shall be cleaned under this item but these areas shall not be measured separately.2) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.3) In case of non performance of work at any or all locations,no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per thousand sqm. | 3,00,000 | Sq M | 0.4 ₹1.2 L | 0.6 ₹1.8 L |
| 2.00 | Cleaning and washing of sewer lines, inspection chambers, man holes etc.including clearing the blockages, if any in the lines by rodding and applying the required water pressure using tankers with hose to ensure easy flow of sewage/waste water etc.complete as per specifications and as directed by Engineer-in-charge. | 120 | Per R M | 47 ₹5,640 | 50 ₹6,000 |
| 2.10Note: 1) Measurement shall be taken along the centre line of pipes including the length of centre line of benching in chambers cleaned. | |||||
| 2.202) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding. | |||||
| 2.303) In case of non performance of work at any or all locations,no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per running metre. | |||||
| 3.00 | Removing and cleaning of chokes/blockages from sewerage lines, manholes, inspection chambers, W.C., gully traps and floor traps etc.by bamboo/ M.S.rods/mechanical means so as to provide the easy flow of sewage/waste water etc.including opening of door bend/jali and refixing the same after clearing of chokage complete as per specifications and as directed by Engineer-in-charge. | 20 | Per choke | 320 ₹6,400 | 350 ₹7,000 |
| 3.10Note 1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding. | |||||
| 3.202) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per choke. | |||||
| 4.00Maintenance of cleanliness around buildings by lifting all waste material, packing boxes, garbage and waste papers etc. on all working days except Sunday and national holidays from all around 20m of the building including transporting the same to the predetermined locations / pits etc. in ARPF campus or in the garbage carrying vehicle of Indore Municipal Corporation standing close to campus ensuring non pilferage etc complete as per specifications and as directed by Engineer-in-Charge | |||||
Tender Value
₹29.5 L
EMD Value
₹59,000
Closing Date
12 Jan 2026, 5:00 pmClosed
CHIEF ENGINEER, RRCAT, INDORE
CSD OFFICE RRCAT INDORE
Maintenance of hygiene by general cleanliness, garbage collection, cleaning and maintenance of roads, disposal ,other hygiene related works, Management of water supply, Miscellaneous Civil and PH works in ARPF complex for RRCAT near vegetable market
2025_RRCAT_892031_1
RRCAT/CSD/W-4381/25-26/60
Open Tender
Civil Works
365 days
RRCAT
Please refer Tender documents.
3 documents required · 3 mandatory
₹0
₹59,000
27 Feb 2026
31 Dec 2025
14 Jan 2026
2 Jan 2026
12 Jan 2026
2 Jan 2026
Imp. Note - 1. The bidder must possess valid EPF & ESIC registration. The bidders need to deposit EPF & ESIC with appropriate authority. The reimbursement for EPF & ESIC deposit shall not be made. 2. The payment of wages to labourers should be made through bank. 3. The bidder must possess sufficient manpower & other resources (as detailed in SGF ) required for the timely completion of work.
Cleaning and washing of sewer lines, inspection chambers, man holes etc.including clearing the blockages, if any in the lines by rodding and applying the required water pressure using tankers with hose to ensure easy flow of sewage/waste water etc.complete as per specifications and as directed by Engineer-in-charge.
Note: 1) Measurement shall be taken along the centre line of pipes including the length of centre line of benching in chambers cleaned.
2) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Removing and cleaning of chokes/blockages from sewerage lines, manholes, inspection chambers, W.C., gully traps and floor traps etc.by bamboo/ M.S.rods/mechanical means so as to provide the easy flow of sewage/waste water etc.including opening of door bend/jali and refixing the same after clearing of chokage complete as per specifications and as directed by Engineer-in-charge.
Note 1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Maintenance of cleanliness around buildings by lifting all waste material, packing boxes, garbage and waste papers etc. on all working days except Sunday and national holidays from all around 20m of the building including transporting the same to the predetermined locations / pits etc. in ARPF campus or in the garbage carrying vehicle of Indore Municipal Corporation standing close to campus ensuring non pilferage etc complete as per specifications and as directed by Engineer-in-Charge
ARPF building and Security post building etc.
Note 1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
General cleaning, sweeping, mopping, dusting, swabbing of floors of the rooms at various storeys, passeges, staircases etc including sweeping, cleaning, washing and swabbling of passages in front of all toilets including the cost of entire cosmetic materials on all working days on daily basis and cleaning of ceilings, external faces of walls & parapets, cleaning of glass panes & other members of windows, doors, ventilators, mirrors, handrails, removing of cobwebs once in fifteen days and daily disposing of sweeped waste up to nearest dust bin located outside of the building as directed, disposing the contents of scattered placed dust bins in to the predetermined locations / pits etc. in ARPF campus for final disposal or putting in to the garbage carrying vehicle of Indore Municipal Corporation standing close to campus ensuring non pilferage etc complete including the cost of required safety tools & tackles, necessary safety kit ,Uniform, vacuum cleaner, the cost of soft nylon brushes, brooms
and all consumables like cleansing agent of approved make and approved cleaning agent, rubbing papers etc. complete as directed by the Engineer-in-charge.
Note: (1) This item shall be applicable for general rooms, corridors, stairways, lobbies etc.This item shall not include cleaning & disinfection of toilets which shall be paid separately under relevant item. Only floor area of the building shall be measured for payment. Half area shall be measured if mopping could not be taken up.
(3) The contractor shall deploy as many number of cosmetic helpers as required to ensure that various jobs in whole area of the building including fortnightly jobs and toilets* (*payable separately) gets finished in one working day.
(4) The choking if any not caused due to fault of contractor and existed prior to taking up of cleaning operations shall be paid separately under relevant item as the same is not included in this item. However choking if any which was not existing prior to taking up of cleaning operations shall be considered as choking caused due to fault of contractor and removal of the same shall have to be borne by the contractor for which payment shall not be admissible.
(5) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
General cleaning,sweeping,swabbing,disinfecting and making the public toilet fit with improved hygiene by satisfactorily cleaning of all types of dado, walls, floors, sanitary fitments like Indian water closet, European water closet, urinals, wash basins, marble or other type of urinal partitions, flushing units etc. either individually or in combination at all level including cleaning of bath zone with or without internal lobby by using mild acid, cleansing agent, bleaching agents, soft nylon brushes, rubbing papers, necessary safety kit, Uniform, ladder,vacuum cleaner etc.including spraying antifungal, anti bacterial fumable liquids,sprinkliling of phenyl, placing of phynapthelene balls, placing air fresheners at ventilators including rectification of joints of tiles using matching coloured air curable compound etc. complete as directed by the Engineer-in-charge.
This item shall be operated for first frequency of the day and the payment for subsequent frequencies shall be payable under item no 7
(3) The choking if any not caused due to fault of contractor and existed prior to taking up of cleaning operations shall be paid separately under relevant item as the same is not included in this item. However choking if any which was not existing prior to taking up of cleaning operations shall be considered as choking caused due to fault of contractor and removal of the same shall have to be borne by the contractor for which payment shall not be admissible.
(4) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
General cleaning and making the public toilet fit for use by satisfactorily cleaning of all types of dado, walls, floors, sanitary fitments like Indian water closet, European water closet, urinals, wash basins, marble or other type of urinal partitions, flushing units, mirror etc. either individually or in combination at all level including cleaning of bath zone with or without internal lobby by using available water, available cleansing agent of approved make and other approved cleansing agent, available brooms, soft nylon brushes, rubbing papers but excluding necessary safety kit, ladder etc including sprinkliling of available phenyl, placing of available phynapthelene balls etc complete as directed by the Engineer-in-charge.
This item shall be operated for second and onward frequencies of the day and the payment for FIRST frequency shall be payable under item no 6
(3) The choking if any not caused due to fault of contractor and existed prior to taking up of cleaning operations shall be paid separately under relevant item as the same is not included in this item. However choking if any which was not existing prior to taking up of cleaning operations shall be considered as choking caused due to fault of contractor and removal of the same shall have to be borne by the contractor for which payment shall not be admissible.
(4) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Cleaning and washing of sewer lines, inspection chambers, man holes etc.including clearing the blockages, if any in the lines by hiring and deploying hydraulic pressuring unit mounted on trucks applying the required water pressure to ensure easy flow of sewage/waste water etc and pumping out the sewage with hose and collected in a carrier for further disposal in oxidation pond etc complete as per specifications and as directed by Engineer-in-charge.
Note: 1) Measurement shall be taken on per job basis. This item shall be applicable for cleaning of medium size septic tank also.
(2) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Cleaning the rain water pipe of all size, shape ,length 2.50m to 10.00m and corresponding terrace areas including removing the blockages if any by rodding and testing the same by pouring water etc.including opening & closing of C I door tees etc.complete as per drawing, specifications and as directed by Engineer-in-charge.
Note:(1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Cleaning the plastered normal masonry storm water drains (depth up to 1.2 mtrs) including removing the debris, grit etc and disposing off the same in pits within a lead of 250 mtrs, including cost of all tools and tackles etc.complete as per specifications and as directed by Engineer-in-charge.
Note:(1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Cleaning the earthen drains (Having bottom width of approx 500mm and depth varying from 0.50 M to 3.00 M), including excavation for trimming the sides and bottom in slope to allow for easy flow of rain water, removing the debris, grit etc and disposing off the same in pits within a lead of 100 mtrs, including cost of all tools and tackles etc.complete as per specifications and as directed by Engineer-in-charge.
Note:(1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Cleaning the storm water pipe outlets of all size, shape ,length located below footpath or area beyond road kerbs including removing the blockages if any by rodding and testing the same by pouring water etc.including digging ditch, if required for a length not exceeding 3.00 for free flow of water etc complete as directed by Engineer-in-charge.
Note:(1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Disposing debris, non value scrap, garbage, heaps of earth, rublles,rotton wood logs and the like by deploying excavator with Operator and Khalasi including collecting the same in a tractor with driver and Khalasi for conveying the same to low lying areas including deploying labourers for unloading the material from tractor, levelling and dressing the ground at both the places i.e. at lifting point as well as at point of disposal so as to carry out the assigned work any where in ARPF premises including the cost of all required tools & tackles, hire charges,fuel,necessary safety kit etc. complete as directed by the Engineer-in-charge.
Note: (1) The payment shall be made for the hours of work performed by the excavator at ARPF's site. The time at which the excavator arrives and starts at site and shuts down shall be noted for payment purposes.
(3) The contractor shall deploy as many number of labourers as required to ensure that work gets finished promptly.
(4) This item shall not be operated for items of dismantling works, earth work, area dressing, routine garbage disposal etc as the same is covered under respective items.
(5) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Disposing by mechanical transport ; the garbage consisting of debris, rubbish, packing boxes, grass etc. from ARPF building to the predetermined locations in the ARPF campus within 3 Km. lead including loading, unloading, levelling, carrying by mechanical transport as required to maintain cleanliness around offices, parks and buildings in ARPF campus including cost of all tools and tackles etc., complete as per specifications and as directed by Engineer-in-charge ( Carriage capacity shall be around 5.00 Cum.).
Making arrangement at all levels for catching rats using Rat Traps handed over by the department by keeping it at places which has high potential of movement of rats, preferably under the furniture or corner of walls including putting peanut butter and paste of flour for attracting rates ensuring its replacement on daily basis to avoid reinfestation including discharging the creature/rat at a distance of about 3.5 KM away in a non habitant locality including washing the trap as required etc complete as directed by the Engineer-in-charge.
Note 1) The payment shall be made per trap as one number. In case rat is not trapped and all activities are performed the quantity shall be considered as one fourth.
3) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Supplying and filling 100 ml liquid soap in the existing soap dispenser installed near wash basins at discrete locations at all levels including emptying the residual liquid, rinsing and washing prior to re-filling, disposing the empty refill pack complete as directed by Engineer in Charge.
Note 1) The payment shall be as one number if entire 100 ml content is filled. In case of partial filling payment shall be made on proportionate basis based on actual quantity filled.
3) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Special housekeeping work in congested and sensitive equipment area by cleaning,sweeping,mopping,dusting,swabbing of floors, cleaning gently with exceptional care, the dust accumulated on equipments by using light duty vacuum cleaner including cleaning of doors/windows/ wall/ceiling surface complete as directed including the cost of all cosmetic materials, required tools & tackles, hire charges of vacuum cleaner, necessary safety kit, uniform, including the cost of soft nylon brushes and consumables like cleansing agent of approved make , rubbing papers etc. complete as directed by the Engineer-in-charge.
Note: (1) Only floor area of the building shall be measured for payment of entire activities.
(3) The contractor shall deploy only such qualified cosmetic helpers who have experience of carrying out work in such areas. Contractor shall deploy required number of personnel along with a supervisor to ensure that various jobs in whole area of the building gets finished very carefully in one working day.
(4) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Cleaning & disinfecting of R C C overhead storage tanks of overall capacity 20000 litre to 25000 litre distributed in two compartments separated by RCC partition wall located on top of roof slab at a height ranging from 5.00 metre to 12.00 metre levels using bleaching powder @ 1 kg each tank including emptying the balance water in the tank below outlet etc , cleaning the tank by applying gentle acid,brooming,brushing and rinsing with bleaching powder safely without causing damage to waterproofing treatment including rinsing thrice with plain water including removing covers and the float valve with ball carefully prior to cleaning operation and refixing the same including removing the sediments if any ,other necessary activities like inspecting the existing M S ladder prior to use, tools & tackles, necessary safety appliances all as per specifications and as directed by the Engineer-in- Charge.
Note: (1) Any damage to cover and/or float valve with or without ball shall be replaced by the contractor at his own cost.
(2) In order to avoid suffocation of workers, contractor must ensure that workers must come out at regular interval to breathe in fresh air.
(3) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Cleaning & disinfecting of R C C underground sumps of capacity ranging from 90000 litre to 100000 litre and depth around 3.00 metre using bleaching powder @ 1.80 kg each tank including emptying the balance water, if any in the tank , cleaning the tank by applying gentle acid,brooming,brushing safely without causing damage to waterproofing treatment including rinsing with bleaching powder followed by rinsing thrice with plain water including removing covers and the float valve with ball carefully prior to cleaning operation and refixing the same including removing the sediments if any etc complete including necessary activities like inspecting the existing M S ladder prior to use, tools & tackles, necessary safety appliances, masks all as per specifications and as directed by the Engineer-in- Charge.
Note: (1) Any damage to cover and/or float valve with or without ball shall be replaced by the contractor at his own cost.
(2) In order to avoid suffocation of workers, contractor must ensure that workers must come out at regular interval to breathe in fresh air.
(3) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Management of receipt and distribution of Narmada water as well as tube well water in ARPF complex by deploying ITI (Fitter/Plumbing trade) trained operator or highly experienced operator daily in close consultation with the engineer of RRCAT or his authorized representative including maintaining the log book, giving daily feed back about the receipt of water, distribution of water either manually or through automation system including monitoring & operating Diesel Engine Pump set , Electric Pump set on as & when required basis depending upon the supply timings of Narmada water supplied by Municipality and User's requirement by ensuring filling of sump as well as Overhead tanks basis without any interruption on all days in close consultation with the engineer and facility Users of RRCAT or their authorized representative including carrying out routine maintenance, oiling & greasing etc of ' pumps, supply & delivery valves float valves etc' including cost of labourers, supply & use of diesel for diesel pump (item continued in the next row),
minor CONSUMABLE items like welding electrodes/ fluxes, fastener sets, gaskets, minor fittings,sundris,transport of deployed staff to inspect daily, the dedicated CI line etc including maintaining the log book, giving daily feed back about the receipt & consumption of water, status of water line, fittings ,valves, pumps etc including carrying out MINOR repairs etc as & when required solely to ensure uninterrupted performance of the system etc all complete as per detailed specifications, standard operating procedures with total adherence to labour laws, contract conditions etc complete job as directed by Engineer in Charge .
Note: 1) The payment shall be based on calendar month whether it is of 31 days or less than 31 days for the entire job carried out as per detailed specifications.
2) Contractor shall take all necessary measures including training if any, minor maintenance of pumps, valves etc as required at his cost to assure uninterrupted performance. Specialized maintenance of pumps, valves etc is not in the scope of this item.
3) Engineer shall have right to disallow any workmen to work without assigning any reason whatsoever.
4) The contractor shall follow up with the officials of RRCAT Security, Civil maintenance cell, Facility Users, Municipality authorities etc as frequently as required to ensure uninterrupted water supply for functional utility.
6) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
Lead charges by mechanical transport for lead exceeding 2 Kms but not exceeding 3 Kms including loading, unloading, stacking, levelling etc.
All soils
Demolishing brick work in cement mortar at all levels including scaffolding, stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead etc. complete.
Dismantling the Mosaic/white glazed/Ceramic/Vitrified tiles /Kotah stone etc. in flooring/dado/skirting etc. including dismantling of bedding mortar, stacking of materials and disposing of debris within 50 metres lead etc. complete.
Demolishing Reinforced cement concrete works by chiselling at all levels including scaffolding, cutting of reinforcement bars by gas cutting, straightening & stacking of steel bars and disposal of unserviceable materials within 50 metres lead etc. complete.
Cutting holes up to 30 cm x 30 cm size in 240 mm thick plastered brick wall in cement mortar including scaffolding, disposal of unserviceable material within 500 mtr. lead and making good the wall with 20 mm thick,1:4 cement plaster,curing etc complete as per drawings, specifications and as directed by the Engineer-in-Charge
Providing & laying in position Cement concrete 1:3:6 using graded stone aggregate 40 mm max. size including consolidating, finishing, curing etc. complete excluding formwork as per specifications.
Providing & laying in position REINFORCED cement concrete of M-20 grade at all heights using graded stone aggregate of 20 mm max. size including machine mixing, consolidation, mechanical vibration, finishing, curing, cost of labour & machineries etc. complete as per specifications but excluding formwork, shuttering and steel reinforcement.
In foundations, footings, plinth beams, base of columns, flooring.
Providing and placing in position REINFORCEMENT using TMT BARS of approved makel etc. having minimum yield strength of Fe 500 conforming to IS 1786, for reinforced cement concrete work at all levels, including cutting, bending, fixing, tying in position with 1.6 mm dia. soft drawn annealed binding wire, with chairs, legs, supports etc. complete including cost of transporting the bars from factory to required location at work site, cost of 1.6 mm dia. soft drawn annealed binding wire, watch & ward, insurance etc complete all as per drawing, specifications and as directed by Engineer-in-charge. (The contractor has to submit the test report & Challan of the reinforcement, procured by him.)
NOTE: Binding wire required for the work will have to be supplied by the contractor at their own cost and will not be measured for payment.
Providing centering and shuttering using timber planks/steel plates including strutting and propping etc. at all heights and removal of the same for in situ reinforced concrete and in plain concrete work
Foundations, footings, base of columns plinth beams, flooring, machine foundations, bed blocks, window cills, copings and mass concrete
Brick work in cement mortar 1:6 using IInd class bricks having a compressive strength not less than 35kg/cm² in drains, compound walls, flower beds & other similar works including curing, raking out joints above ground level, simultaneous pointing below G.L. etc. complete as per specifications and as directed by Engineer-in-Charge.
Cement plastering to internal /external surfaces of walls up to height of 10m, 20 mm thick in two coats, backing coat 15mm thick with cement mortar 1:4, 2nd coat 5mm thick in cement mortar 1:4 and finishing with neat cement punning over brick walls or concrete surfaces, including hacking the concrete surfaces, double scaffolding wherever necessary, curing etc., complete as per drawings, specifications and as directed by the Engineer-in-charge.
Providing and laying polyvinyl (PVC) rolls/tiles manufactured by M/s. Premier/Responsive/Birla or other approved company of thickness 2mm heavy duty solid vinyl flooring of approved colour, pattern and designs for flooring, skirting/dado laid on existing smooth cement tile or concrete or plastered finish, with suitable adhesive as per manufacturer's specifications, close jointed by PVC welding and finished to proper bends, slope and plumb etc. complete.
Non Slippery Ceramic tile flooring/dado using 6mm thick matt finished ceramic tiles of sizes as mentioned below, 1st quality approved make over 20mm thick cement mortar 1:3 bedding, close jointed and pointed with matching cement slurry using white cement pigment mixed with, finished to levels slope or plumb as required including 20mm thick cement mortar 1:3 bedding, making good the surface before bedding, cutting of tiles, curing, acid washing etc. complete.
For flooring using tiles of size 450x450mm and 300x300mm
For Dado/Skirting using tiles of size 300x450mm
Providing and fixing in position first class double charged vitrified porcelain tiles (thickness to be specified by the manufacturers) with water absorption less than 0.08% and conforming to IS:15622, of approved manufacturer of size 600mmx 600mm of approved color, pattern and design for flooring, skirting or dado laid in floor, wall of existing concrete or plastered surface over 20 mm thick cement mortar 1:3 bedding close jointed and pointed with matching slurry @ 3.30 kg/sqm using white cement with pigments finished to levels, slope or plumb as required including cement mortar bedding, cutting of tiles to required size and curing, acid washing etc. complete.
Providing and laying/fixing in position 15mm to 18mm thick machine polished granite slabs of approved colour and quality including machine/hand cut, polishing, buffing the edges all in line, level, (curvature corners if required) in 20mm thick cement mortar 1:3 bedding with best workmanship, finishing, curing, complete in platforms, shelves, wash basin, cills, jambs, facias, treads and risers etc. complete.
Other than black shades
Providing and fixing 2mm thick epoxy based joint less flooring for (Approved make) over existing flooring such as concrete floor, tiles, wood, metal etc. formulated out to required levels, thickness slopes and finished smooth or rough including curing, preparing the surfaces such as filling holes, cracks, joints, wherever necessary by epoxy based trowelling compound, including providing and applying one coat of two component epoxy based primer including cost of materials and labours etc. complete as per manufacturer's recommendation.
Preparing the surface and etching with 10% commercial hydrochloric acid wherever necessary, neutralising the etched areas by washing with 5% solution of soda ash, applying one coat of pigmented epoxy based primer followed by one coat of epoxy based trowelling compound, cutting and grinding the surfaces wherever necessary using waterproof quality emery paper and applying three finishing coats of epoxy based polyamine/polyamide cured special acid and alkali resistant paint of approved make & tint including preparing surfaces, scrapping, filling holes, cracks, joints, wherever necessary with epoxy based trowelling compound, cost of all materials, scaffolding and labour, tools & tackles, safety appliances and as per manufacturer's recommendations.
With POLYAMIDE cured epoxy paint
Painting plastered surfaces with two/three coats of Acrylic emulsion paint of approved shade and make over one coat of approved cement primer including preparing the surfaces, filling with full wall putty, scaffolding and cleaning, tools & tackles, safety appliances etc. complete
Two finishing coats over a coat of primer
Painting the exterior walls and roof with two coats of approved shade including preparing the surface by removing loose dust and dirt with stiff brush and washing the surface with clean water, treating the surface with antifungal chemical wherever required, filling holes with putty, scaffolding and cleaning, tools & tackles, safety appliances etc. complete as per specification.
Supplying, lowering, laying, RCC spun pipes (Class NP2) of IS : 458 with necessary collars, laid to correct grade and levels at all depths including cutting to length, jointing with hemp yarn and C.M. 1:1, caulking the joints and finishing, curing, testing etc. complete.
300 mm dia
Providing, laying, jointing, fixing and testing CPVC pipes of grade SDR - 11 as per IS:15778 including CPVC plain & brass threaded fittings like elbows, collars, tees, unions, couplings, reducers, enlargers, bends, CPVC MTA, FTA and all other fittings required for the completion, having thermal stability for hot & cold water supply and also as per the code of practice of water supply in buildings of IS: 2065 including laying under the floors, chasing in walls, roof slabs and making good the same to the original conditions, including fixing the pipe with clamps at 1m spacing, cost of all jointing materials like hemp yarn, white or red lead, clamps, wooden gutties, screws, cement, sand etc. complete testing the pipes with clean water as per specifications.
20mm nominal size
25mm nominal size
32mm nominal size
40mm nominal size
Providing and fixing in position heavy pattern screw down gun metal GATE VALVEs of approved make conforming to IS:778 with hand wheels at top including testing for 10 kg/cm2 pressure with clean and potable water with a minimum testing duration of two hours etc. as per specifications and as directed by Engineer-in-charge.
Providing, laying, jointing, fixing and testing PVC rigid pipes of class 'B' of approved brands for sewerage ensuring thermal stability for waste water, sewage, acids etc. including all PVC fittings, jointing with durable solvent, testing the pipes at a pressure of 6 Kg per Sq cm etc. complete as per drawing, specifications and as directed by the Engineer-in Charge.
Providing and fixing HDPE/CPVC Floor trap of self cleansing design with 75mm outlet having a minimum water seal of 50mm with stainless steel grating on top of approved make including necessary 1:2:4 cement concrete for embedding the trap etc. as per specifications all complete.
Providing and fixing heavy quality fancy variety C.P. brass screw down 15mm n.b.Stop cock/ Angular Stop cocks of approved make confirming to IS:8931 on G.I. pipe line
Providing and fixing 15mm n.b. qurter turn fancy variety heavy quality C.P. brass two way angle cock (approved make) conforming to IS : 781. complete as per drawing, specifications and as directed by the Engineer-in-Charge.
Providing & fixing 15mm dia heavy quality C.P. brass screw down BIB TAPS of approved (heavy) make conforming to IS-781 on G.I. lines, complete as per drawing, specifications and as directed by the Engineer-in-Charge.
Providing & fixing approved make heavy quality C. P. brass screw down PILLAR TAP with jam nut, of 15mm n.b.of approved (heavy) make conforming to I.S. 1795, as per specifications and as directed by Engineer-in-charge.
Providing and fixing heavy quality of approved make Plastic Seat (for EWC sheet)and Lid of approved shade with C.P. brass pillar hinges etc. all complete confirming of IS:2548
Filling the joints of floor tiles, dado tiles, the joint between floor & dado and the joint between WC & floor etc. using matching cement with suitable fast setting compound etc complete as directed by Engineer-in-charge. Note: The payment shall be made for floor/dado area treated as above without making deduction of area occupied by WC
Providing & fixing in position finished C.P. brass coat hangers of approved make and satin finish with nettle fold screws etc. complete as per drawings, specifications and as directed and approved by Engineer-in-Charge.
Providing and fixing C.P. brass Toilet pape roll Holder of approved make fixing on wall using C.P. brass screws, rawl plug etc all complete.
Providing and fixing heavy quality C.P. brass screw down 15mm n.b. SWAN NECK TAP of approved make confirming to IS:8931 on G.I. pipe line
Skilled Male (Plumber/Carpanter/Mason)
Unskilled Male Helper
Servicing of Emergency exit doors by dismantling for overhauling of individual parts associated with operation of door including cleaning of materials causing door jam, removing the rust scales by sand papering, servicing of spindle & calm arrangement, inspecting, taking out and replacing the damaged or defective or worn out nut, bolts, washers or rivets as required including all welding, drilling, straightening, grinding, scaffolding, ladders, tools, tackles, with all consumables such as lubricants kerosene, grease, rivets, washers etc. making good any damages to civil works, cleaning the area by disposing off scraps, debris etc, oiling, greasing and demonstrating proper functioning of the door after such service etc. complete as directed by Engineer-in-charge.
Servicing of Collapsible doors or sliding type of grill gates by dismantling for overhauling of individual parts associated with smooth sliding action, cleaning of track to remove all type of waste, dusts etc, removing the rust scales by sand papering, reasonably tightening of rivets by spot hammer press, inspecting, taking out and replacing the damaged or defective or worn out nut, bolts, washers or rivets, as required including all welding, drilling, straightening, grinding, scaffolding, ladders, tools, tackles, with all consumables such as lubricants kerosene, grease, rivets, washers etc. making good any damages to civil works, cleaning the area by disposing off scraps, debris etc, oiling, greasing and demonstrating proper functioning of the door/gate after such service etc. complete as directed by Engineer-in-charge.
Repainting of old painted surfaces with two coats of paint of approved shade and make including preparing the surfaces, removal of old paint, if any, sand papering, filling with putty as required, scaffolding and cleaning, tools & tackles, safety appliances etc. complete.
Using SYNTHETIC ENAMEL paint
Providing & fixing Aluminium glazing clip for fixing the glasses in door/window shutters including cutting the clip in size, removing the existing worn out clip etc complete as per specifications and as directed by the Engineer-in-Charge.
Providing & fixing 2 mm thick Aluminium glazing plate of height about 50mm with appropriate grooves for holding & fixing the glasses in door/window shutters including cutting the plate in size, removing the existing worn out plate etc complete as per specifications and as directed by the Engineer-in-Charge.
Providing and fixing in position up to & including 6.00 metre height from adjoining ground level Bajra or Plain & clear Sheet glass/Float glass/Wired glass of approved make and of following thickness fixed to Aluminum/M.S. windows, doors, partitions, ventilators etc. with edges champhered (wherever required) with PVC/Neoprene Gasket or rubber lining as required etc all complete as per drawing and specifications and as directed by the Engineer-in-Charge.
3.50 mm thick Bajra glass
Providing and fixing in position clear sheet glass/float glass of approved make and of following thickness fixed to aluminum windows, doors, partitions, ventilators etc. with edges champhered (wherever required) with PVC/Neoprene Gasket Lining etc. complete. Note: Only the clear opening of Glass shall be measured for payment. Aluminum snap beading shall be measured and paid under relevant item.
With glass panes of 4.0 mm thickness (weight not less than 10.00 kg/sqm)
With glass panes of 5.0 mm thickness (weight not less than 12.50 kg/sqm)
With glass panes of 6.0 mm thickness (weight not less than 15.00 kg/sqm)
Note : (1) Only the clear opening of Glass shall be measured for payment. Aluminum snap beading shall be measured and paid separately under relevant item.
Note : (2) Broken glass pieces shall be disposed off in a safe manner to a place as directed.
Note : (3) Temporary scaffolding shall be paid extra under relevant item if the bottom level of glass is located at 6.00 metre height above adjoining ground level.
Providing and fixing in position Aluminum partitions, doors, windows, ventilators, louvers, fixed glazing, sliding windows, north light glazing, aluminum rough ground etc. with extruded and anodized (5 microns) to natural aluminum colour, aluminum sections, anodized aluminum beadings, anodised aluminum sheets manufactured to relevant IS codes and using minimum 2mm thick (or as specified) heavy sections of approved equivalent make including cost of pivots, approved door and window handles, PVC/Neoprene Gasket lining, stainless steel screws, mastic filling, weather strips, tower bolts, nuts, washers etc. as required complete as per drawing, specifications and as directed by Engineer-in-Charge.
Providing and fixing heavy duty Locking arrangements for sliding windows usingapproved make of size 85 mm ± 10 mm, including built in heavy duty plated M.S. spring, necessary screws, all materials, labourers etc. complete as directed by the Engineer-in-charge.
Providing & fixing anodized Aluminum Beading of size 9.5 mm x 9.5 mm for fixing glass for steel windows with necessary screws etc. complete as directed by the Engineer-in-charge.
Providing & fixing rubber lining for fixing glass for steel / aluminium windows with necessary screws etc. complete as directed by the Engineer-in-charge.
Providing and fixing sleek Model heavy duty Hydraulic Door Closer of approved make with necessary screws, fixing to the aluminium/wooden/M.S. doors complete as per drawing, specifications including all labour, transporting etc. and as directed by the Engineer-in-charge. Note:- Tax paid bill showing warranty period shall be submitted by the contractor.
Providing and fixing sleek Model heavy duty Hydraulic Door Closer of approved make conforming to IS 1564 with necessary screws & accessories, fixing to the Aluminium/Wooden/M.S.doors complete as per drawing, specifications including all labour, transporting etc. and as directed by the Engineer-in-charge. Note:- Tax paid bill showing warranty period shall be submitted by the contractor.
Providing & fixing in position at all heights 12 mm thick both side pre-laminated particle board of exterior grade I / Type II conforming to I S 12823, bonded with Phenol Formaldehyde resin in partitions/doors using approved standard Aluminium beading including cost of screws, cost for cutting to required sizes, wastages, fixing to existing frame with nut/bolts/screws as required including necessary incidental charges for ensuring its position, proper line & level etc all complete as per drawing and specifications and as directed by the Engineer-in-Charge.
Note : Aluminum frame work and Aluminum Snap beading used for fixing boards shall be measured and paid for separately under relevant item.
Providing & fixing locally fabricated 100 mm x 20 mm x 3 mm brass plate with suitable recess to accommodate 12.5 mm dia stainless steel ball bearing for easy movement of Aluminium Shutter fixed at top or bottom of Aluminium Shutter after removing aluminium door shutter & the same after positioning the ball based pivot including making holes in frame, cost of necessary hardware etc. complete as per specifications and as directed by the Engineer-in-Charge.
Providing & fixing locally available best quality 400 mm long concealed type Aluminium vertical tower bolt in an existing Aluminium door after removing aluminium door shutter & the same after positioning the concealed type tower bolt including cost of necessary hardware etc. complete as per specifications and as directed by the Engineer-in-Charge.
Providing & fixing best quality pin type pivotal assembly of approved make, for easy movement of Aluminium shutter fixed at top or bottom of Aluminium Shutter after removing aluminium door shutter & the same after positioning the pivot assembly including making holes in frame, cost of necessary hardware etc. complete as per specifications and as directed by the Engineer-in-Charge.
Providing & fixing push plate made of exterior grade water proof ply of 20mm thickness and 150mm high of required length including formica front & rear facing of 0.5 mm thick including providing & fixing Aluminium C Channel of size 25 mm x 25 mm x 1.5 mm on all edges of push plate for strengthening existing Aluminium doors, if required including removing aluminium door shutter, drilling holes for fixing screws, nut, bolts etc & the same after positioning the push plate including cost of necessary hardware etc. complete as per specifications and as directed by the Engineer-in-Charge.
Providing & fixing 15 micron anodized aluminium Section of appoved make for top rail or bottom rail or lock rail of size 114.5 mm x 44.5 mm x 3 mm of required length in lieu of worn out/damaged member including removing aluminium door shutter, drilling holes for fixing screws, nut, bolts & fixing the new member and then the shutter, existing fixtures etc in position including cost of necessary hardware etc. complete as per specifications and as directed by the Engineer-in-Charge.
Servicing of single or double leaf Aluminium doors of size not exceeding 3.00 sqm including removing of door shutter from position, adjusting, aligning & servicing floor spring and the cover plate, realigning the door, oiling the pinion/ pin type pivot or ball type pivot, tightening of all screws nuts, bolts used for fixing of hinges, tower bolts, door closure, push plates, handles, beadings, glazing clips etc. to ensure smooth functioning of aluminium doors etc. all but excluding servicing of floor spring complete as per specifications and as directed by the Engineer-in-Charge.
(2) All other items like floor spring, Aluminium Sections, hydraulic door closure, hinges, concealed tower bolts, pinion/ pin type pivot, ball type pivot, tower bolts, glasses, particle boards as required shall be paid under relevant items.
(3) Replacement of floor spring if required shall be paid under relevant items.
Servicing of single or double leaf Aluminium doors of size exceeding 3.00 sqm including removing of door shutter from position, adjusting, aligning and servicing floor spring and re-fixing the cover plate, realigning the door, oiling the pinion/ pin type pivot or ball type pivot, tightening of all screws nuts, bolts used for fixing of hinges, tower bolts, door closure, push plates, handles, beadings, glazing clips etc. to ensure smooth functioning of aluminium doors etc. all but excluding servicing of floor spring complete as per specifications and as directed by the Engineer-in-Charge.
(2) All other items like floor spring, Aluminium Sections, hydraulic door closure, hinges, concealed tower bolts, pinion/ pin type pivot, ball type pivot, tower bolts, glasses, particle boards as required shall be paid under relevant items.
(3) Replacement of floor spring if required shall be paid under relevant items.
Servicing of Glass doors of size up to 5.00 sqm including removing of door shutter from position, adjusting & aligning floor spring and re-fixing the cover plate, realigning the door, oiling and servicing the glass door hydraulic hinges / servicing of floor spring, tightening of all screws nuts, bolts used for fixing of hinges, push plates, handles etc. to ensure smooth functioning of glass doors etc. complete as per specifications and as directed by the Engineer-in-Charge.
(2) All other items like Aluminium / M.S.sections, hydraulic door hinges, glasses, as required shall be paid under relevant items.
(3) If the glass of door will be broken during servicing, the same will be replaced by the contractor at free of cost.
Extra for erecting steel scaffolding unit 10.00 metre high using vertical pipes made of 40 mm n b , M.S. pipe of 10 G thickness and horizontal pipes made of 40 mm n b , M.S. pipe of 20 G thickness, fixed vertically & horizontally at spacing not exceeding 1200 mm resting over base plate of size 100 mm x 100 mm x 6 mm below vertical pipes, diagonal bracings shall be made of 40 mm n b , M.S. pipe of 20 BG thickness, tying all junctions with standard M.S. couplers including providing & fixing sitting unit made of closely spaced Bamboo Challis, having approximately 40 mm thickness tying the whole unit with existing reliable supports ,safety barricades at working level dismantling the same as & when required including screws ,nails etc complete as per drawing, specifications and as directed by the Engineer-in-Charge. Note: Only Plan area shall be measured for payment. De-assembled scaffolding material shall remain contractor's property.
Providing & fixing EUROPEAN WATER CLOSET suite comprising of :
a. White vitreous china pedestal type water closet (European type W.C. pan) in vitreous Chinaware with internal 'P' or 'S' trap conforming to IS: 2556 of approved make.
b. PVC, low level flushing cistern 10 litres capacity of approved make and mounted brackets with double syphonic pattern and all internal fittings conforming to IS: 7231.
c. 15mm n.b. heavy quality P.V.C. inlet connection with brass unions connected at ends.
d. 15mm n.b. screw down heavy quality, fancy variety C.P. brass Two nos. stop cock of approved make. conforming to IS:8931.
e. Solid plastic heavy quality seat with lid of approved make and colour with C.P brass pillar hinges, conforming to IS :2548 (Part I and II)
f. Health faucet (Hand Shower) with 8mm dia. 1.2 metre long Flexible tube & wall hook of approved make.
g. Jet spray (butterfly) with 1.00m long heavy quality PVC tube & nozzle of approved make.
Providing and fixing approved ORISSA PATTERN W.C. SUITE comprising of :
a. Orissa pattern W.C. best Indian make white or colour glazed vitreous chinaware, size 580 mm x 400mm with ‘P’ or ‘S’ trap, of approved make conforming to IS: 2556
b. PVC low level flushing cistern 10 litres capacity with all fittings of approved make
c. 32mm n.b. heavy quality P.V.C flush pipe of appropriate length with all PVC specials, etc. concealed in wall.
d.15 mm n.b. heavy quality P.V.C inlet connection with brass unions connected at ends.
e. 15mm n.b. screw down heavy quality, fancy variety C.P. brass stop cock of approved make. conforming to IS:8931.
Collecting public drinking water samples or effluent water samples as directed, from scaterred locations in ARPF/RRCAT, carefully in containers disinfected as per I S 1622-1987 for arranging testing on specified parameters as per IS 3025 part 1 to 60 to ascertain suitability of water for intended use, complete as per following notes and as directed by the Engineer-in- Charge.
Note: (1) The contractor at his own cost need to deploy labourers to operate valves, taps, pump of tube wells to collect water samples from descrete locations anywhere in ARPF/RRCAT premises.Opening & refixing of fittings, if required, shall be carried out by the department only.
Note: (2) The contractor at his own cost shall get the water tested from M P Pollution Control Board Laboratory to ascertain pH, suspended solids,Total solids, chloride, Lead, Iron,Sulphate,BOD, COD, MPN,Dissolved Oxygen,Turbidity,Total hardness, Calcium Hardness,Magnesium Hardness etc.for drinking water and pH, suspended solids,,BOD,COD, MPN,Dissolved Oxygen,Total hardness,Calcium Hardness,Magnesium Hardness etc.for effluent water. Nothing extra shall be paid for submission of test results of additional parameters.
Note: (3) The contractor need to bear all expenditures for delivering the samples and later in obtaining test report from from M P Pollution Control Board Laboratory including safety kits, tools & tacles, testing charges, cost of container, arranging to & fro transport accompanying departmental representative from ARPF/RRCAT premises to & from M P Pollution Control Board Laboratory to assure authenticity of collected samples and safe handing over of the same in laboratory.
Providing pest control treatment to entire ARPF complex at all the floors in all the rooms, labs., toilets, WCs, bathrooms, halls, stores, passages etc. for controlling entry of rodents, lizards, cockroaches, ants, bugs etc. using chemicals Cyfluthrine, Fpronil Gel, Delta Matherine, Bhromodylene cake as required, Burofumigation with sulphas etc. complete as per manufacturers specifications & as directed by EIC. The treatment shall be done at monthly duration for total area 2500.00 Sqm. approx.
Note- (1) The treatment shall be guanteed for one month. It means during one month period no occurrence of rodents, lizards, cockroaches, ants, bugs etc . If occurred recovery shall be made for affected areas.
(2) During operations proper hygiene should be maintained. Special care shall be taken during /after the treatment in labs. & allied areas. Proper cleaning should be done after the treatment to remove the left over of chemicals.
(3) The area for one operation means for 2500.00 Sqm (approx.) area for every month duration.
Please Enable Macros to View BoQ information
stage.html
html • 0.03 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Tendernotice_1.pdf
PDF • 7.76 MB
prefferedmakes.pdf
Tender Documents • 0.30 MB
ScheduleA.pdf
Tender Documents • 0.75 MB
ScheduleB.pdf
Tender Documents • 0.56 MB
SGF4381.pdf
Tender Documents • 1.99 MB
SpecsCIVIL1.pdf
Tender Documents • 2.01 MB
SPNPH.pdf
Tender Documents • 1.79 MB
BOQ_937605.xls
BOQ • 0.40 MB
Conditions.pdf
Tender Documents • 1.38 MB
NIT.pdf
Tender Documents • 7.75 MB
Download all tender documents and submit your bid