Rewinding of 60 HP any make horizontal submersible motor pump panel and sluice valve at Juna somwariya tanki pump house

Labor charge for complete rewinding work of 60 HP 440 volt 3 phase any make horizental submersible motor pump cutting of burnt winding taking out burnt winding wire & stesmelted chips p.v.c. material from slots cleaning decorborizing of complette stator slots rotor etc. making new coils fixing in the stator slots insulation etc. complete i/c soldering, brazing, refitting of rewinding motor alignment and dynamically balance of rotor horizental alignment with pump coupling trial & testing etc. complete.

Providing & fixing complete servicing of pump chamber pulley moment of impeller unit with as per required fitting works.

Providing & fixing impullar unit as per required sample with new S.S. check nut, wiser etc. complete.

Providing & carefulley disconnecting of above motor pump at suction & delivery base plate i/c after repairing work complete alignment pump set connecting delivery and suction with required hardware material labor charge for laoding & unloading site at work shop to site.

Providing & complete repairing of 60 HP ATS starter for 2 nos. set at Juna somwariya pump house i/c labor charge for fitting with burn equipment & changing burn winding & lugs etc. as per required complete work.

Providing and fixing Alpha+ A type ELMEASURE multifunction relay with 80 to 300V AC showing all the parameters like Amp Volt and frequencey

Providing and fixing on delay timer relay for controling motor 0-10 time fraction, 3.5 SMF, 440V installed in starter panel

Providing and fixing GIC L &t make 440V three phase with 65±10VAC, operating time 2sec release time 7 sec single phasing preventer for Starter panel

Providing and fixing under voltage/over current relay 500V 50 Hz, 2 A L & T make for potection of motor

Providing & fixing of 145-30 or similar contactor in motor starter ATS panel no. 1 of Juna Somwariya water tank. Three contactors have a pole of 3 pole. They also comw tih auxiliary contacts of 2 no. + 2 nc. The contactors category includes all devices that contact or energize electrical conductors, such as swiches, relays and contacts with required wiring and lugs etc.

63 AMP, 10kA, TP MCB

RYB electric tap roll

Supplying and fixing knife type 120 Amp fuse link

Removing all the burnt wiring and fixing complete wiring of panel for removel of fault with required size of wire, cu lugs, farruls and number with tie

Providing and fixing Auxillary Contacts 2 NO + 2 NC for Contactors

Providing for complete replacing 250/300 amper , 415 volt 50Hz moulded case circuit breaker (MCCB) of any standard make for main power supply equipment.

Digital amp. meter 0-150 amp. for starter.

LED indacator lamp unit for starter

On/Off switch unit for starter

Labour charges for opening and refitting of following dia.(SV) valve for oiling & greasing work. I/C excavation of pit as per site requirement or cleaning work of chamber and cutting of old rusted nut bolt with by chisel or gas cutter opening refitting of spindle rod, GM check nut gate etc. providing and fixing of new nut bolt with washer gland rope, rubber packing etc. fixture, check nut guide work. Continuous dewatering by pump during the work trial and testing after the completion of work i/c the cost of grease, transportation of the T&P and all labour with risk cover. Complete job work.

150 m.m. dia s/v

300 m.m. dia s/v, Butterfly

Providing & Supplying the ductile iron mechanical joint collar with following glands confiring ti IS 9523/2000 in nominal diameter sized with external bitumen coating and internal cement motor lining i/c rubber ring and nut-bolt as per requirement

150 mm dia

300 mm dia

Providing and fixing i.e. replacement of G.M. check nut in following size of sluice valve made out by single piece.

150 mm dia

300 mm dia

Repairing of following dia sluice valve Ci fixture chek nut catcher(guide) both side i/c welding, boring, threading & clamping finishing cutting as per size of chek nut

150 mm dia

300mm dia

Supply of SS 410 Spindle Rod for following dia sluice valve

150 mm dia

300 mm dia

Please Enable Macros to View BoQ information